40690195 supply of dual coated enamelled copper winding wirdual coated enamelled copper winding wir,dual coated enamelled copper winding wire size 22 swg [0.711mm] confirming to is/13730 1993/pt xiii.grade of covering shall be grade 2 [medium covering] [ warranty period: 30 months after the date of delivery ] => limited...
40680826 tender for repairing of borewell at main building; 1 opening of motor taking out old burnt wire & parts, cleaning of slots of stator & opening of pump with all labour etc. required for proper completion of work 2 rewinding of 10hp submersible motor with suitable size of insulated copper winding wire including winding charges. 3 s / f of upper & lower housing bush ( motor ) 4 s / f of thrust plate with segment 5 s / f of rubber bush ( pump ) 6 making interlocking arrangement with 1 ms iron strip. 7 s / f of nuts / bolts & rubber packing 8 lowering of repaired 10hp pumpset with column pipecomplete with all t / p & labour. => limited...
40620331 supply of supper enammelled round copper winding wire polyster basesupper enammelled round copper winding wire polyster base,supper enammelled round copper winding wire polyster base medium covering for elevated temperature confg,to is:13730 elevated temperature confg,to is:13730 (part 13) 1993. each reel should specn: sealed originally accompanied with wtc from the manufaturer size 16 swg. make. khaitan,milan,atalas,hwp,icc only. [ warranty period: 30 months after the date of delivery ] => limited...
40600495 auction sale of scrap copper brunt wire, copper coil, winding wire and other copper wire of sort and sizes. the approx metal content is as under copper 98%, tape varnish insulation cotton dust etc 2% note loading by purchaser. location: lying in godown b, near pole k...
40540095 tender for construction of floor under mudd shoot in factory; 2 earth filling in plinth including supply of necessary qty. of local earth from a distance not exceeding 8 km. from the site of work and including watering , ramming, and dressing etc. required for proper completion of the work 3 providing and laying in cement concrete 1:4:8 of not less than strength of m 150 stone ballast 40 mm. normal size and app. coarse sand and 1 cement and curing complete includig supply of all material. 4 rcc work with cement approved coarse sand and 2 cm. gauge approoved stone grit in the proporation 1:2:4 in rcc raft excluding supply of reinforcement and its banding the same with 24 b w g winding wire and necessary centring and shuttering etc. 5 mild steel or iron work in plain work such as reinforced concreat and overall steel brought to required shape as necessary including binding for proper completion of the work and excluding supply of steel....
40391468 tender for work of purchasing decentralized material for edd i azamgarh 2 0.81 s.e. alu. winding wire 3 11 kv tpmo switch 4 11 kv copper busbar 5 11 kv draw out fuse set 6 33 kv e clamp 7 33 kv f bracket for stp pole 8 alluminium crimpinglug 400 sqmm 9 alluminium crimping lug 185 sqmm 10 alluminium crimping lug 250 sqmm 11 alluminium jointing sleeves for dog 12 alluminium lug 50 mm 13 aluminium lug 120 mm 14 aluminium lug 240 mm 15 aluminium lug 70 mm 16 aluminium paint 17 barbed wire 18 cable end termination alu. lug 19 clamp holding hanging 150mm cable w. n&b 20 control cable copper 10x2.5 sq mm pvc 21 copper control cable 2x2.5 sq.mm. 22 copper control cable 4x2.5 sq.mm. 23 copper control cable 6x2.5 sq.mm. 24 copper z clamp 25 cross arm holding clampforpccpole 26 cross arm holding clamp st pole with n&b 27 danger board with clamp for 33 kv line 28 danger plate u / s 29 dcp ( fire extinguisher ) 5kg 30 dead end clamp 31 distribution box 3 phase 32 distribution box clamp 33 dropper channal clamp 34 e / f bracket 35 eye hook 36 f bracket for 33 kv line 37 f clamp for pcc pole8.5 meter 38 f clamp for stpwith n&b 39 f bracket 40 gaurding angle clamp 41 gi pipe 6 inch dia for xlpe cable 42 guarding clamp for pcc pole 43 hpsv lamp 250 watt 44 l.t.bracket 36 45 led 105 110 w 46 led 245 260 w 47 lt clamp for 8.5 mpole 48 lt clamp for stp 11 mpole 49 lt distribution box 50 lt shackle insulator 75x90 mm 51 lug. alu.240 sq.m.m. 52 lug. alu.300 sq.m.m. 53 lug. alu.400 sq.m.m. 54 lug. alu.630 sq.m.m. 55 lug. alu.70 sq.m.m. 56 lug. alu.120 sq.m.m. 57 lug. alu.50 sq.m.m. 58 m.s. clamp 6½ 50x6 m.m. 59 mcb 60 mccb 100a with enclosure 61 mccb 240a with enclosure 62 ms bolt & nut ( with 1 washer ) 1.25x3 / 8ø 63 ms nut & bolt off size 3x2.5 64 number plate 65 nut bolt with washer off size 66 pg clamp 67 red oxide paint 68 rubber mat 69 stay clampfor 11 mstp pole 70 stay insulator 71 suspension clamp 72 t off clamp for 8.5 mpcc pole 73 t off clamp for stp 74 t off clamp with n&b 75 top channel clamp for 8.5 mpcc pol 76 top channel clamp for 11 m stp 77 top channel / dropper chann. holding clamp 78 top clamp with nut & bolt 79 z clamp 80 z type copper strip 600 / 400 / 250 kva transformer 81 2x2.5 sq mm aluminium cable pvc 82 33 kv fuse set 83 33 kv cross arm holding clamps with n&b 84 brass cable gland for 3.5x120mm u / s 85 cableend termination brass gland 3.5x240 86 circuit l.t.500a / 500v 87 e bracket for 11 kv pin 88 fuse set 11 kv 89 lt stud for 10kva t / f to 100 kva transformer 90 oil seal packing for10kva transformer to 100 kva transformer 91 silica gel...
40354160 various electric work against additional business plan 2023 24 for quality power supply in aligarh city on semi turn key basis under the area eudd 1 aligarh 1 safe carriage of following material from store centre, sarsol, aligarh to the respective site of work including the work of its loading & unloading at the repective ends and its erection as per direction of supervising engineer, including the cost of arrangement of labour, t&p carrier etc. required for proper completion of work as per resspo norms: 2 11 mtrs. st pole 3 13 mtrs. st pole 4 earthing of pole 5 stay complete ( gi stay rod 16x1800mm, 5 kgs. stay wire 7 / 8, stay clamps, insulator, bolts, nuts & washers ) 6 33 kv xlpe cable 3x300 sq.mm. 7 acsr dog conductor 8 acsr weasel conductor 9 ab cable 3x120+1x95+x16 sq.mm. 10 distribution transformer 250 kva 11 distribution transformer 400kva 12 11 kv d.o. fuse set 13 11 kv tpmo 14 11 kv pin insulator with pin 15 11 kv polymer pin insulator with pin 16 11kv disc insulator 17 11kv disc fitting 18 11 kv f bracket 19 l.t. pvccable 1x400 mm. 20 l.t. xlpe cable 3.5x240 mm. 21 11 kv v type cross arm 22 gi wire 6 swg 23 gi wire 10 swg 24 33 kv control pannel ( double ) 25 33 kv cable jointing kit 3x300sq.mm. ( outdoor ) 26 stone pad 27 al lug 240 sqmm 28 al lug 400 sqmm 29 top channel size 125x65x2240 mm. 30 dropper channel size 100x50x2028 mm. 31 tee off chennal size 125x65x1300mm. 32 base angle size 75x75x6x2028 mm. 33 pole clamp 34 danger board with clamp 35 barbed wire 36 nut bolt & washer 37 number plate with clamp 38 gaurding angle 39 i bolt 40 aluminium winding wire 41 t / f end clamp 240 sqmm 42 t / f end clamp 400 sqmm 43 construction of plinth at various 11 / 0.4 kv sub station suitable for distribution transformer having size 5’x 5’ x 5’ out which 2’ below the ground. work will include digging of foundation 2’ deep & brick work with ist class bricks having cement and sand mortar of ratio 1:6 on all the walls, each of 9” thickness. the area inside the wall shall be duly filled by mud up to the height of appropriate level from ground level and shall be duly watered & rammed. above the filling c.c. of ration 1:6:12 ( cement sand and brick ballast ) giving 4” layer shall be provided. above c.c. layer rcc layer having 4” thickness and with ratio 1:2:4 of cement sand and stone ballast shall be provided re enforcement shall be provided by providing net of ( 8 nos. + 8 nos. ) m.s. rods of size 10 mm dia and each of 5’ length in the middle of the top of c.c. layer. the plinth shall be plastered with 12mm thick plaster in ratio 1:4 at all sides. this work will include cost of labour, t&p and all material required for construction of plinth which shall be provided by the contractor as per resspo norms. 44 providing and fixing of welded wire mesh fencing around transformer plinth with m.s. angle of size 35x35x6 mm. length and 1.20 meters height, such panels shall be supported on m.s. angle from of size 40x40x6 mm. having 04 nos. corner supports of height 1.65 meters including extended legs for grouting which will be used as a door for entry of the personnel or removal / shifting of transformer with welded hinges, sliding belt etc. for locking the arrangement as per drawing and specifications the fencing will be painted one coat of red oxide primer and then two coats of bus green synthetic enamel paint. the rates should be inclusive of all materials required for proper completion of above work ( length of each fencing approx. 11 meters ) 45 dismantling and removal of following material from the existing line and then stacking in the respective je’s ( store ) as per direction of supervising engineer. it includes the work of cartage, cost of labour, t&p carrier etc. required for proper completion of work. 46 dismentling of 63kva distribution transformer 47 dismentling of 250kva distribution transformer...
40352144 supply of supper enammelled round copper winding wire polyster basesupper enammelled round copper winding wire polyster base,supper enammelled round copper winding wire polyster base medium covering for elevated temperature confg,to is:13730 elevated temperature confg,to is:13730 (part 13) 1993. each reel should specn: sealed originally accompanied with wtc from the manufaturer size 16 swg. make. khaitan,milan,atalas,hwp,icc only. => limited...
40282926 supply of dual coated enamelled copper winding wire size 16 swg ( 1.626 ) confirming to is:13730 part 13.grade of covering shall be grade 2 ( medium covering ) . [ warranty period: 30 months after the date of delivery ] amm / tms / kanpur, ncr uttar pradesh 2793.00 kg...
40243192 supply of winding wire for 3 phase tm stator bare size 4.0 x 2.0 mm, specn. hife 650030 alt 4. note: this item is reserved for procurement from rdso approved suppliers only. as per specn. hife 650030 alt 4 [ warranty period: 30 months after the date of delivery ] ...
40210140 supply of decentralised material for district plan ( 20 cr. ) and additional business plan ( 16 cr. ) in azamgarh district supplyfollowing materials 2 0.81 s.e. alu. winding wire 3 11 kv tpmo switch 4 11 kv t off channel clamp for 8.5 m long 5 11kv f clamp for pcc pole 6 33 kv f bracket for stp pole 7 alluminium crimpinglug 400 sqmm 8 alluminium crimping lug 250 sqmm 9 alluminium lugs 90 mm 10 aluminium lug 120 mm 11 aluminium lug 35 mm 12 aluminium lug 70 mm 13 aluminium paint 14 barbed wire 15 copper control cable 2x2.5 sq.mm. 16 copper control cable 4x2.5 sq.mm. 17 copper z clamp 18 copper z clamp for 250 kva t / f 19 cross arm holding clamp 20 cross arm holding clampforpccpole 21 cross arm holding clamp pcc pole 8.5m 22 cross arm holding clamp st pole with n&b 23 danger board 24 dead end clamp 25 dead end clamp with eye hook 26 distribution box 1 phase 27 distribution box 3 phase 28 distribution box clamp 29 dropper channal clamp 30 eye hook 31 f bracket for pcc pole 32 f clamp for pcc pole8.5 meter 33 f clamp for stpwith n&b 34 f clamp for top insulator 35 f bracket 36 fuse wire no.14 swg 37 g.i. pipe bore earthing 60 feet deep 38 g.i.pipe 6 dia 39 gaurding angle clamp 40 guarding clamp for pcc pole 41 holding clamp for pcc pole 8.5 mtr. 42 j type hook 43 l.t. shackle insulator 44 l.t.bracket 36 45 lt clamp for 8.5 mpole 46 lt distribution box 47 lt shackle insulator 75x90 mm 48 lt shackle insulator clamp for pcc with 49 lug. alu.120 sq.m.m. 50 lug. alu.150 sq.m.m. 51 lug. alu.240 sq.m.m. 52 lug. alu.300 sq.m.m. 53 lug. alu.70 sq.m.m. 54 m.s. clamp 6½ 50x6 m.m. 55 m.s. dropper channel 100x50x5x2028 mm 56 ms bolt & nut ( with 1 washer ) 1.25x3 / 8ø 57 ms bolt with nut 16x165 mm 58 ms nut & bolt off size 3x2.5 59 pg clamp 60 pg clamp for weasel to weasel 61 pg clamp rabbit 62 pg connector 33 kv 63 pipe earthing 40mm dia gi pipe 3000 mm 64 plinth&foundation for 33 / 0.4 kv 400 t / f 65 red oxide paint 66 silica gel breather for power t / f 67 stay insulator 68 suspension clamp 69 suspension clamp with eyehook 70 t off channel 0.35 mtr for h.t. line tap 71 t off clamp for 8.5 mpcc pole 72 t off clamp for stp 73 t off clamp with n&b 74 t / f holding clamp 75 top channel clamp for 8.5 mpcc pol 76 top channel clamp for 11 m stp 77 top channel / dropper chann. holding clamp 78 top clamp with nut & bolt 79 top tee off clamp for 8.5 mtr pcc pole 80 z clamp 81 2x2.5 sq mm aluminium cable pvc 82 33 kv fuse set 83 circuit l.t.500a / 500v 84 fuse set 11 kv 85 lt shackle insulator 100x115 mm 86 l type cooper clamp for 250 kva t / f...
40102651 supply of supper enammelled round copper winding wire polyster basesupper enammelled round copper winding wire polyster base,supper enammelled round copper winding wire polyster base medium covering for elevated temperature confg,to is:13730 elevated temperature confg,to is:13730 (part 13) 1993. each reel should specn: sealed originally accompanied with wtc from the manufaturer size 16 swg. make. khaitan,milan,atalas,hwp,icc only. [ warranty period: 30 months after the date of delivery ] => limited...
39915180 supply of different materials for the substations, switchgear maintenance under eudc ii, prayagraj in the head of o and m. , supply of materials , 11 kv incomming vcb ct 800/400/5 amp (schinder make) , 11 kv outgoing vcb ct 400/200/5 amp(schinder make) , 11 kv vcb vaccum intrupter (schinder make) , 11 kv vcb spout (schinder make) , 11 kv vcb trally charging motor , silica gel power t/f , copper winding wire 8/10/12 swg , 11 kv vcb spring contact , 11 kv vcb male female contact , trolly spring charging moter (schinder make) 150watt , tripping and charging coil , pg clamp for power t/f bushing...
39889804 tender for double paper recovering of aluminium winding wire & strip of damaged transformer coil at various workshop under ewc, agra...
39849680 supply of corona resistant round enameled winding wire as per rdsos specification no.rdso / 2014 / el / spec / 0116 [ revision 0 ] size 19.5 swg. specn: rdsos specification no.rdso / 2014 / el / spec / 0116 [ revision 0 ] [ warranty period: 30 months after the date of delivery ] => limited...
39849606 supply of corona resistant round enameled winding wire as per rdsos specification no.rdso / 2014 / el / spec / 0116 [ revision 0 ] size 18 swg. specn: rdsos specification no.rdso / 2014 / el / spec / 0116 [ revision 0 ] [ warranty period: 30 months after the date of delivery ] => limited...
39849602 supply of corona resistant round enameled winding wire as per rdsos specification no.rdso / 2014 / el / spec / 0116 [ revision 0 ] size 20 swg. specn: rdsos specification no.rdso / 2014 / el / spec / 0116 [ revision 0 ] [ warranty period: 30 months after the date of delivery ] => limited...
39838136 supply of corona resistant round enameled winding wire as per rdsos specification no.rdso / 2014 / el / spec / 0116 [ revision 0 ] size 17 swg. specn: rdsos specification no.rdso / 2014 / el / spec / 0116 [ revision 0 ] [ warranty period: 30 months after the date of delivery ] , corona resistant round enameled winding wire as per rdsos specification no. rdso / 2014 / el / spec / 0116 [ revision 0 ] size 18.5 swg. specn: rdsos specification no. rdso / 2014 / el / spec / 0116 [ revision 0 ] [ warranty period: 30 months after the date of delivery ] ...
39717023 tender for 33 / 11 k, under the marginal power distribution sub division of godda, under the power distribution division hamirpur. b. 11 kb in electricity substation chhani. work of guarding ( 2 ) 33 / 11 k. v. 11 kb operated from power sub station chhanau. guarding work of road crossing babehta, mulpur etc. in various districts ( 3 ) 33 / 11 k.b. s.t. in dow parsani guhalla operated from power sub station chhani. line extension work ( 4 ) 33 / 11 kv. 1 kb powered by electric filter. which gogkandar is operated by lt in parsani guhalla? line extension work ( 5 ) 33 / 11 k.b. lt at dam garen in tichut sub centre, chhani. line expansion work 2 pcc pole 8.5 m long (provided by department) 3 stone pad 300x300x75 mm 4 cross arm holding clamps with bolt & nut (provided by department) 5 11 kv pin insulator with pin insulator (provided by department) 6 11 kv disc fitting 45 kn & t&c (provided by department) 7 11 kv disc insulator with pinc (provided by department) 8 ms angle 75x75x6x2028 mm 9 alluminium winding wire 6 swg 10 gi barbed wire 11 t off channel 12 top channel 125x65x2240 mm 13 dropper channel 100x50x2240 mm 14 gaurding angle 50x50x6x2500 mm 15 gi wire 6 swg 16 gi wire 8 swg 17 clamp with nut & bolt 18 clamp suitable for pcc pole 19 eye bolt 12x100 mm 20 jointing sleeves for acsr weasel conductor 21 danger board with clamps 22 dead end clamp 23 suspension clamp with eye hook (insulated) 24 pg (lt bare netural connector) 95/70, 70/35 sqmm 25 stay wire gi (7/3.15) 7/10 swg 26 stay set 16x1800 27 lt insulation piercing clamp of 3x120 & 3x95 & 3x50 for abc 28 lt insulation piercing connector 120 to 50 sqmm, 95 to 50 sqmm 29 25 kva transformer (provided by department) 30 acsr weasel conductor (provided by department) 31 lt abc cable 3x95+1x70+1x16 sqmm(provided by department) 32 distribution box 3 phase 33 three phase distribution box with clamp 34 11 kv tpmo 35 lug alu 25 sqmm 36 11 kv stay insulator 37 11 kv stay clamp for pcc pole 8.5 38 earthing complete 39 clamp with nut & bolt for gaurding angle 40 lt pvc cable 3.5x70/35 sqmm 41 grouting of stay 42 grouting of pole ...
39710995 work of 11 kv / lt line / vcb / transformer construction / installation in edsd – ii & ivsoron & amanpur in the edd ( rural ) , kasganj under the juridiction of edc, kasganj on semi turn key basis stone pad 3 concreating of st pole 4 f bracket 5 holding clamp 6 stay rod complete 7 earthing rod complete 8 megger (5000volt) 9 frp loader siddi 8 meter long 10 chain tader 3 ton 11 drowase(kmla clamp) for dog/rabbit (2type) 12 tool kit 13 roller(ab cable) 14 electrod earthing rod 15 11 kv switchgear 16 danger board 17 holding clamp for top channel , tpmo & fuse set 18 ms angel (t/ f base) 19 cabel jointing kit 11 kv 3x120 sqmm o/d 20 dead & clamp 21 cabel jointing kit 11 kv 3x 120sqmm i/d 22 11 kv al. 3x300 sqmm xlpe cabel 23 3x120 sqmm xlpe cabel 24 battery charger 12 volt 25 battery set 12 volt 26 t off channel 27 lt teeoff with bolt & nut 28 ms channel 125x65x1300 mm 29 11 kv tpmo 30 11 kv fuse set 31 3 phase distrubution box 32 piercing connector 33 m.s. angel iron 65x65x6mm, 2700 mm long bracing with 4 clamp 34 dead end assembly 35 suspension clamp with i hook 36 ms top channel 37 ms dropper channel 38 lt abccable 3x50 sqmm. 39 i hook 40 lt insulating piercing clamp 41 al. lug 400 sqmm. 42 lt pvc cable al. 3.5x150/70sqmm. 43 11 kv vcb incoming ctr 600/300/5a 44 11 kv vcb outgoing ctr 200/100/5a 45 acsr weasel conductor 46 alluminimum winding wire 06 swg 47 lt clamp 48 nut bolt & washers 49 painting number mark with paint 50 number of plate 51 red oxide paint 52 alluminimum paint 53 barbed wire 54 erection of material 55 extension of control room 56 dismentaling of old line isolater & erection / fixing of33 kv line isolater 57 laying & fixing of 3x300 sqmm xlpe cabel 58 erection of 11 kv vcb incoming ctr 600/300/5a/10a 350 mva 59 erection of 11 kv vcb outgoing ctr 200/100/5a 350 mva 60 fixing of 3 phase distrubution box 61 installation of 11 kv/ 33/11 kv jointing kit indoor/ outdoors 3x120/185/ 3x300 sq mm. 62 fixing of piercing connector 63 fixing of suspension clamp 64 fixing of lt insulating piercing clamp 65 installtion of 11kv fuse set 66 laying & fixing of11 kv lt xlpe cable 3x120 sqmm. 67 erection of single support including complete h.t/l.t fittings s.t. pole 11 mtr. sp 55 including earthing, grouting & muffing of pole. 68 erection of single support including complete h.t/l.t fittings pcc pole 8.5 mtrincluding earthing, grouting & muffing of pole. 69 erection ofdouble pole support including complete h.t/l.t fittings pcc pole 8.5 mtrincluding earthing, grouting & muffing of pole. 70 erection of single support including complete h.t/l.t fittings s.t. pole 13 mtr. sp 55 including earthing, grouting & muffing of pole. 71 installation & fixing battery charger 12 volt & battery set 12 volt 72 fixing of danger board 73 fixing of barbed wire 74 laying/ fixing of alluminimum winding wire 06 75 erection of double pole on s.t. pole including the work of complete lines.t. pole 11 mtr. sp 55including earthing, grouting & muffing of pole. 76 fixing of 11 kv tpmo set complete 77 erection/ fixing of 11 kv switchgear 78 erection of stay set complete including the work of nuzzling etc. 79 laying sagging stringing, binding and jumpering acsr weasel conductor 80 laying & fixing of abc cabel 3x50 sqmm. 81 painting of st pole with red oxide & ailunimum paintas per respo norms 82 laying & fixing of lt pvc cable al. 3.5 x150/70 sqmm. 83 carriage from store & installation of 25kva t/f 11/0.4 kva new in all respect 84 underground railway crossingpermission fees ...
39685128 work of construction and strengthening of 33 kv line under power distribution division ii, orai, capacity increase of 33 / 11 kv power sub station and other work related to the sub station. work of construction and strengthening of 11 kv line, installation of 11 / 0.4 kb distribution transformers and work of increasing the capacity, in which the amount will be paid by the executing agency as per requirement. 1 commissioning ofthe whole following work including carriage, commissioning with all required material as per resspo norms. please read the boq carefully then quote the rates. 2 abc bunch 3x120 with all fitting 3 m.s t off channel with all fitting 4 11 kv pin with nut with all fitting 5 33 kv pin with nut with all fitting 6 11 kv disc & fitting with all fitting 7 energization of 100 kva t/f with all fitting as per resspo norms. 8 energization of 250 kva t/f with all fitting including earthing, plinth & fancing as per resspo norms. 9 energization of 400 kva t/f with all fitting including earthing, plinth & fancing as per resspo norms. 10 base angle t/f with all fitting 11 stay set complete 12 earthing complete 13 tpmo with all fitting 14 11 kv fuse set with all fitting 15 33 kv fuse set with all fitting 16 stp 11 m with earthing, grouting & concreating of support & stay as per resspo norms. 17 pcc 8.5 m with earthing, grouting & concreating of support & stay as per resspo norms. 18 11 kv f clamp with all fitting 19 11 kv x arm with clamp 20 weasel conductor with all fitting 21 33 kv control panel single t/f with all fitting 22 dcp al winding wire with all fitting 23 installation/replacement of 33 kv ct with all fitting as per resspo norms 24 installation/replacement of 33 kv pt outdoor with all fitting as per resspo norms 25 outdoor switchyard with all fitting 26 installation/replacement of 33 kv vcb with all fitting 27 installation/replacement of 11 kv vcb i/c with all fitting 28 installation/replacement of 11 kv vcb o/g with all fitting 29 energization of 10 mva t/f with all fitting as per resspo norms. 30 11 kv 3x300 xlpe cable with cable laying charge as per resspo norms 31 installation/replacement of h/s cable j kit 3x300 mm o/d for 33 kv with all fitting 32 installation/replacement of h/s cable j kit 3x300 mm i/d for 33 kv with all fittng 33 installation/replacement of cable box 3x185 mm i/d for 33 kv with all fitting 34 installation/replacement of cable box 3x240 mm i/d for 33 kv with all fitting 35 in the works related to 33/11 kv power substation, all the old materials (power t/f, 11/0.4 kv t/f, 33 and 11 kv cables, steel scrap, conductors, ct/pt, vcb, control panel etc.) will be dismantled by the contractor and the old dismantled material will be taken from the pit site and deposited in the store. 36 clearing of the line route by cutting of tree branches during erection of line and also upto the time of energisation of site incharge ...
39684945 the work of 11 kv / lt line / vcb / transformer construction / installation in edsd – i & iiiganjdundwara &patiyali in the edd, kasganj under the juridiction of edc, kasganj on semi turn key basis.= 1 supply of material 2 stone pad 3 09 mtr pcc pole 4 concreating of st pole 5 f bracket 6 holding clamp 7 stay rod complete 8 earthing rod complete 9 danger board 10 gi pipe 6 dia 11 megger (5000volt) 12 frp loader siddi 8 meter long 13 chain tader 3 ton 14 drowase(kmla clamp) for dog/rabbit (2type) 15 tool kit 16 roller(ab cable) 17 electrod earthing rod 18 holding clamp for top channel , tpmo & fuse set 19 ms angel (t/ f base) 20 cabel jointing kit 11 kv 3x185 sqmm o/d 21 dead & clamp 22 lt pvc cable 3.5x400 sqmm. 23 copper l piece 50x225x10mm 24 copper l piece62x225x10mm 25 4 core lt mcb with box (ls) 26 al leg long barrel off size l.s. 27 lt pvc cabel 1x200 sqmm 28 lt pvc cabel 1x400 sqmm 29 lt pvc cabel 1x600 sqmm 30 lt pvc cabel 1x1000 sqmm 31 cabel jointing kit 11 kv 3x 185sqmm i/d 32 3x300 sqmm xlpe cabel 33 3x185 sqmm xlpe cabel 34 battery charger 24 volt 35 battery set 24 volt 36 t off channel 37 lt teeoff with bolt & nut 38 ms channel 125x65x1300 mm 39 alluminimum joiting sleeves 40 11 kv tpmo 41 11 kv fuse set 42 3 phase distrubution box 43 piercing connector 44 m.s. angel iron 65x65x6mm, 2700 mm long bracing with 4 clamp 45 suspension clamp with i hook 46 ms top channel 47 ms dropper channel 48 lt abccable 3x120 sqmm. 49 transformer bus complete set 50 bus coupler 350 mva 51 lt pvc cable al. 3.5x150/70sqmm. 52 11 kv vcb incoming ctr 600/300/10a 53 11 kv vcb outgoing ctr 200/100/5a 54 4x2.5 sqmm control cabel 55 2x2.5 sqmm control cabel 56 alluminimum winding wire 06 swg 57 g.i. wire 04 mm 08 swg 58 g.i. wire05 mm 06 swg & 10 swg 59 irag bolt 60 indoor equipment (earthmat) for 05 mva t/f 61 pg clamp 62 33 kv fuse set 63 armour rod with females 64 nut bolt & washers 65 160 mm o/d pn 4 pe 80 grade uvstblised hdpe pipe 66 painting number mark with paint 67 number of plate 68 red oxide paint 69 alluminimum paint 70 barbed wire 71 number of plate with clamp for pcc pole 72 90 ibs rail pieces (44.64 kh/m) for t/f 73 33 kv vcb with double t/f control pannel ct 200/100/a with structure (i) 33 kv vcb (ii) control pannel 1/c for 33 kv single t/f (iii) ct 200/100/1 1a (iv) steel structure 74 erection of material 75 tree cutting compensation 76 erection & fabrication of structure with all material for 33 kv line isolater 77 erection & fixing of33 kv line isolater 78 erection & fabrication of structure with all material for transformer bus complete set 79 erection & fabrication of bus coupler 350 mva 80 erection & fabrication of structure with all material for bus isolator 81 erection & fabrication of structure with all material for 33 kv fuse set 82 erection & fabrication of structure with all material for post insulator 83 erection & fabrication of structure with all material for 33 kv lightening arresters. 84 erection & fabrication of structure with all material for of 90 lbs rail pieces for transformer)44.64 kg/m) 85 fabrication of structure with all materialof plinth foundation of5 mva transformer in all respect at vendors cost. 86 fabrication of structure with all materialof plinth foundation ofvcb in all respect at vendors cost. 87 erection & fixing of indoor equipment (earthmat) for 05 mva t/f 88 laying & fixing of 3x300 sqmm xlpe cabel 89 laying oflt pvc cabel 1x200 sqmm 90 laying of lt pvc cabel 1x400 sqmm 91 laying of lt pvc cabel 1x600 sqmm 92 laying of lt pvc cabel 1x1000 sqmm 93 laying of lt pvc cable 3.5x400 sqmm. 94 fixing of copper l piece 50x225x10mm 95 fixing of copper l piece62x225x10mm 96 fixing of 4 core lt mcb with box (ls) 97 fixing of al leg long barrel off size l.s. 98 laying & fixing of 3x185 sqmm xlpe cabel 99 erection of 11 kv vcb incoming ctr 600/300/5a/10a 350 mva 100 erection of 11 kv vcb outgoing ctr 200/100/5a 350 mva 101 fixing of 3 phase distrubution box 102 fabrication of structure with all material laying of 11 kv cable including cost of sand and bricks at vendors cost. 103 fabrication of structure with all material for making of 11 kv cable boxes mounted with switchgears and transformers at vendors cost. 104 installation of 11 kv/ 33/11 kv jointing kit outdoors 3x120/185/ 3x300 sq mm. 105 laying of4x2.5 sq mm (control cable) 106 laying of2x2.5 sq mm (control cable) 107 fabrication of structure with all material for painting of indoor equipments at vendors cost. 108 fabrication of painting & s/s structure at vendors cost. 109 fabrication of structure with all material for sundries at vendors cost. 110 laying & fixing hdpe pipeunder ground through hdd method 111 installtion of 11kv fuse set 112 erection of single support including complete h.t/l.t fittings s.t. pole 11 mtr. sp 55 including earthing, grouting & muffing of pole. 113 erection of single support including complete h.t/l.t fittings pcc pole 8.5 mtrincluding earthing, grouting & muffing of pole. 114 erection ofdouble pole support including complete h.t/l.t fittings pcc pole 8.5 mtrincluding earthing, grouting & muffing of pole. 115 erection of single support including complete h.t/l.t fittings pcc pole 09 mtrincluding earthing, grouting & muffing of pole. 116 erection of single support including complete h.t/l.t fittings s.t. pole 13 mtr. sp 55 including earthing, grouting & muffing of pole. 117 installation & fixing battery charger 24 volt & battery set 24 volt 118 fixing of danger board 119 fixing of barbed wire 120 laying/ fixing of alluminimum winding wire 06 121 fixing of 11 kv tpmo set complete 122 erection of stay set complete including the work of nuzzling etc. 123 laying sagging stringing, binding and jumpering acsr weasel conductor 124 laying sagging stringing, binding and jumpering acsr dog conductor 125 laying sagging stringing, binding and jumpering acsr rabit conductor 126 fixing of alluminimum jointing sleeves 127 fixing of guarding angel with clamp 128 laying & fixing of g.i. wire 04 mm 06/08/10swg 129 painting of st pole with red oxide & ailunimum paintas per respo norms 130 laying & fixing of lt abccable 3x120 sqmm. 131 laying & fixing of lt pvc cable al. 3.5 x150/70 sqmm. 132 carriage from store & installation of 100 kva t/f 11/0.4 kva new in all respect 133 connecting ht cabel connection from 33 kv side & 11 kv side of 05 mva power transformer 134 water level earthing by boring and lowering of g.i. pipe size 40 mm dia & thickness 2 mm into the ground at 20 mtr depth or upto the water level with the lower end of solid copper cone approx 225 mm long and 750 gm in weight shall be provided and screwed in pipe as well as bringing out a continuous copper wire 6 swg from the cone up to the ground surface where it will be bolted to the m.s. earth strip for transformer body & neutral connection, the earth strip will be welded to the g.i. pipe and neutral earthing support. all required material provided/ supply by the contractor own his cost. 135 making of m.s. angle ladder type frame of angle (75x75x8mm) & gi strip (50x6mm) near power transformer for power cable with concreting of the same in the ground and proper clamping (50x6mm) of the same with transformer cable. 136 making of m.s. angle frame of (75x75x8mm) in l shape to connect t/f neutral by flexible copper strip including cost of copper strip & wll be connected to newly constructed well type earthing for power t/f neutral as per respo norms. 137 underground railway crossingpermission fees 138 charges for dismantling work: work includes dismantling from site and cartage of same materails from site/location to central store/any other place as per instruction of je/sdo/ee concerned. 139 11 kv vcb incoming ctr 600/300/10a 140 old & damage isolator set 141 11 kv vcb outgoing ctr 200/100/5a 142 g.i. wire (scrap) 143 acsr dog /conductor (scrap) ...
39665574 various electric work against additional business plan 2023 24 for quality power supply in aligarh city on semi turn key basis under the area eudd 1 aligarh 1 safe carriage of following material from store centre, sarsol, aligarh to the respective site of work including the work of its loading & unloading at the repective ends and its erection as per direction of supervising engineer, including the cost of arrangement of labour, t&p carrier etc. required for proper completion of work as per resspo norms: 2 11 mtrs. st pole 3 13 mtrs. st pole 4 earthing of pole 5 stay complete(gi stay rod 16x1800mm, 5 kgs. stay wire 7/8, stay clamps, insulator, bolts, nuts & washers) 6 33 kv xlpe cable 3x300 sq.mm. 7 acsr dog conductor 8 acsr weasel conductor 9 ab cable 3x120+1x95+x16 sq.mm. 10 distribution transformer 250 kva 11 distribution transformer 400kva 12 11 kv d.o. fuse set 13 11 kv tpmo 14 11 kv pin insulator with pin 15 11 kv polymer pin insulator with pin 16 11kv disc insulator 17 11kv disc fitting 18 11 kv f bracket 19 l.t. pvccable 1x400 mm. 20 l.t. xlpe cable 3.5x240 mm. 21 11 kv v type cross arm 22 gi wire 6 swg 23 gi wire 10 swg 24 33 kv control pannel (double) 25 33 kv cable jointing kit 3x300sq.mm. (outdoor) 26 stone pad 27 al lug 240 sqmm 28 al lug 400 sqmm 29 top channel size 125x65x2240 mm. 30 dropper channel size 100x50x2028 mm. 31 tee off chennal size 125x65x1300mm. 32 base angle size 75x75x6x2028 mm. 33 pole clamp 34 danger board with clamp 35 barbed wire 36 nut bolt & washer 37 number plate with clamp 38 gaurding angle 39 i bolt 40 aluminium winding wire 41 t/f end clamp 240 sqmm 42 t/f end clamp 400 sqmm 43 construction of plinth at various 11/0.4 kv sub station suitable for distribution transformer having size 5’x 5’ x 5’ out which 2’ below the ground. work will include digging of foundation 2’ deep & brick work with ist class bricks having cement and sand mortar of ratio 1:6 on all the walls, each of 9” thickness. the area inside the wall shall be duly filled by mud up to the height of appropriate level from ground level and shall be duly watered & rammed. above the filling c.c. of ration 1:6:12 (cement sand and brick ballast) giving 4” layer shall be provided. above c.c. layer rcc layer having 4” thickness and with ratio 1:2:4 of cement sand and stone ballast shall be provided re enforcement shall be provided by providing net of (8 nos. + 8 nos.) m.s. rods of size 10 mm dia and each of 5’ length in the middle of the top of c.c. layer. the plinth shall be plastered with 12mm thick plaster in ratio 1:4 at all sides. this work will include cost of labour, t&p and all material required for construction of plinth which shall be provided by the contractor as per resspo norms. 44 providing and fixing of welded wire mesh fencing around transformer plinth with m.s. angle of size 35x35x6 mm. length and 1.20 meters height, such panels shall be supported on m.s. angle from of size 40x40x6 mm. having 04 nos. corner supports of height 1.65 meters including extended legs for grouting which will be used as a door for entry of the personnel or removal/shifting of transformer with welded hinges, sliding belt etc. for locking the arrangement as per drawing and specifications the fencing will be painted one coat of red oxide primer and then two coats of bus green synthetic enamel paint. the rates should be inclusive of all materials required for proper completion of above work (length of each fencing approx. 11 meters) 45 dismantling and removal of following material from the existing line and then stacking in the respective je’s (store) as per direction of supervising engineer. it includes the work of cartage, cost of labour, t&p carrier etc. required for proper completion of work. 46 dismentling of 63kva distribution transformer 47 dismentling of 250kva distribution transformer ...
39665244 various electric work against municipal corporation for quality power supply in aligarh city on semi turn key basis under the area eudd 1 aligarh 1 safe carriage of following material from store centre, sarsol, aligarh to the respective site of work including the work of its loading & unloading at the repective ends and its erection as per direction of supervising engineer, including the cost of arrangement of labour, t&p carrier etc. required for proper completion of work as per resspo norms: 2 11 mtrs. st pole 3 13 mtrs. st pole 4 9 mtrs. st pole 5 earthing complete 6 stay complete ( gi stay rod 16x1800mm, 5 kgs. stay wire 7 / 8, stay clamps, insulator, bolts, nuts & washers ) 7 11 kv xlpe cable 3x70sq.mm. 8 11 kv xlpe cable 3x185sq.mm. 9 33 kv xlpe cable 3x300 sq.mm. 10 acsr dog conductor 11 distribution box with clamp 12 ab cable 3x120+1x95+x16 sq.mm. 13 distribution transformer 250 kva 14 distribution transformer 400kva 15 11 kv d.o. fuse set 16 11 kv tpmo 17 33 kv pin insulator 18 33 kv pin with nut 19 11 kv pin insulator with pin 20 11 kv polymer pin insulator with pin 21 33kv disc fitting 22 33kv disc insulator 70kn 23 33 kv f clamp 24 l.t. pvccable 1x400 mm. 25 33 kv v type cross arm 26 gi wire 6 swg 27 gi wire 10 swg 28 33 kv bus isolator 29 11 kv cable jointing kit 3x70sq.mm. ( outdoor ) 30 11 kv cable jointing kit 3x185sq.mm. ( outdoor ) 31 33 kv cable jointing kit 3x300sq.mm. ( outdoor ) 32 stone pad 33 abc connector ( piercing ) 34 suspension clamp with i hook 35 deadend clamp withi hook 36 al lug 240 sqmm 37 al lug 400 sqmm 38 top channel size 125x65x2240 mm. 39 dropper channel size 100x50x2028 mm. 40 tee off chennal size 125x65x1300 mm. 41 base angle size 75x75x6x2028 mm. 42 pole clamp 43 danger board with clamp 44 barbed wire 45 nut bolt & washer 46 number plate with clamp 47 gaurding angle 48 i bolt 49 800a fix type lt acb with microprocessor based release, breaking capacity 50ka 50 aluminium winding wire 51 t / f end clamp 240 sqmm 52 t / f end clamp 400 sqmm 53 neutral & body earthing of distribution transformer by digging of pit upto water level depth ( approx. 125 feet ) and then inserting 1 ¼” dia gi pipe of ‘a’ grade, conforming to the requirement of is specification and then connecting the top of the inserted pipe and transformer body through gi strip of size 40x6 mm with the help of nut and bolt or through gas welding, as per direction of supervising engineer. it includes the cost of all material labour, t&p, carrier etc. required for proper completion of work. the aforesaid work shall be carried out as per resspo norms. 54 construction of plinth at various 11 / 0.4 kv sub station suitable for distribution transformer having size 5’x 5’ x 5’ out which 2’ below the ground. work will include digging of foundation 2’ deep & brick work with ist class bricks having cement and sand mortar of ratio 1:6 on all the walls, each of 9” thickness. the area inside the wall shall be duly filled by mud up to the height of appropriate level from ground level and shall be duly watered & rammed. above the filling c.c. of ration 1:6:12 ( cement sand and brick ballast ) giving 4” layer shall be provided. above c.c. layer rcc layer having 4” thickness and with ratio 1:2:4 of cement sand and stone ballast shall be provided re enforcement shall be provided by providing net of ( 8 nos. + 8 nos. ) m.s. rods of size 10 mm dia and each of 5’ length in the middle of the top of c.c. layer. the plinth shall be plastered with 12mm thick plaster in ratio 1:4 at all sides. this work will include cost of labour, t&p and all material required for construction of plinth which shall be provided by the contractor as per resspo norms. 55 providing and fixing of welded wire mesh fencing around transformer plinth with m.s. angle of size 35x35x6 mm. length and 1.20 meters height, such panels shall be supported on m.s. angle from of size 40x40x6 mm. having 04 nos. corner supports of height 1.65 meters including extended legs for grouting which will be used as a door for entry of the personnel or removal / shifting of transformer with welded hinges, sliding belt etc. for locking the arrangement as per drawing and specifications the fencing will be painted one coat of red oxide primer and then two coats of bus green synthetic enamel paint. the rates should be inclusive of all materials required for proper completion of above work ( length of each fencing approx. 11 meters ) 56 dismantling and removal of following material from the existing line and then stacking in the respective je’s ( store ) as per direction of supervising engineer. it includes the work of cartage, cost of labour, t&p carrier etc. required for proper completion of work. 57 dismentling of 160kva distribution transformer 58 dismentling of 100kva distribution transformer 59 dismentling of 250kva distribution transformer...
39665113 tender for half yearly maintenance and repair works of residential colony at victoria park, meerut for the financial year 2023 24. 1 excavation in foundation in ordinary soil ( loam, clay or sand ) including lift upto 1.5 metreand lead upto 30 metreincluding filling, watering, and ramming of excavated earth into the trenches or into the space between the building and the side of the foundation or in to the plinth and removal & disposal of surplus earth as directes by the e / i up to a distance of 30m from the foundation trenches. csi no. 4.01 2 clearing jungle including uprooting of rank vegetations, grass, bush, wood, trees and saplings of girth upto 30cm measured at a height of 1.0m above ground level and removal of rubbish upto a distance of 50m outside the periphery of uppcl area cleared. csi no. 4.08 3 cleaning of grass and removal of rubbish upto a distance of 50 moutside the uppcl area cleaned. csi no. 4.09 4 earth filling under floors and / or sub station area including cost of earth when obtained from with in 8 kmoutside uppcl area including its roylty and carriage including watering, ramming in 20 cm layers and dressing of earth etc. all complete. csi no. 4.10 5 earth filling in bulk in open areas including cost of the earth when obtained from outside corporation’s area including its carriage, loading / unloading, spreading, watering and ramming in 20cm layers and dressing of earth etc. rates including cost of earth, labour, t&p and royality of earth etc. required for proper completion of the work.csi no. 4.11 ( as per old schedule 2020 21 ) 6 providing and injecting chemical emulsion for post constructional anti termite treatment treatment of soil under existing floors using chemical emulsion @ 1 liter / hole at 300mm interval including drilling 12mm dia holes and plugging them with cement mortar 1:2 ( 1 cement : 2 coarse sand ) after filling with chlorpyriphose / lindane e.c. 20% with 1% concentration.csi no. 4.15 ( as per old schedule 2020 21 ) 7 concrete with 4cm gauge i class brickballast, coarse sand ( f.m. 1.8 to 2.5 ) and cement in proportion of 12:6:1 in foundations and under floors including supply of all materials, labour and tools and plants etc. required for proper completion. csi no. 5.01 8 concrete with 4cm gaugestone ballast, coarse sand ( f.m. 1.8 to 2.5 ) & cement in proportion of 12:6:1 in foundations &under floors including supply of all materials, labour and tools and plants etc. required for proper completion. csi no. 5.02 9 concrete with 4cm gauge i class brickballast, coarse sand ( ( f.m. 1.8 to 2.5 ) and cement in proportion of 10:5:1 in foundations and under floors including supply of all materials, labour and tools and plants etc. required for proper completion. csi no. 5.03 10 cement concrete with 2cm gauge approved hard stone ballast, coarse sand ( f.m. 1.8 to 2.5 ) and cement in proportion of 4:2:1including supply of all materials, labour, side shuttering ifrequired and t&p etc. required for proper completion of work.csi no. 5.06 11 precast cement concrete door sills, chaukhats boundary posts, shelves and similar small work with cement, approved coarse sand ( f.m. 1.8 to 2.5 ) and 2 cm gauge graded approved hard stone ballast in the proportion 1:2:4, excluding reinforcement but including fixing the same in position including cost of all other material, labor and t&p.csi no. 5.09 12 rcc work with cement, approved coarse sand ( f.m. 1.8 to 2.5 ) and2 cm gauge graded approved hard stone ballast like granit, quartzite etc from dalla, jhansi or other quarries in proportion 1:2:4in lintels of doors and windows, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and t&p.csi no. 5.10 13 rcc work with cement, approved coarse sand ( f.m. 1.8 to 2.5 ) and2 cm gauge graded approved hard stone ballast like granite, quartzite etc from dalla, jhansi or other quarries in proportion 1:1.5:3inslab, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and t&p.csi no. 5.24 14 rcc work with cement, approved coarse sand ( f.m. 1.8 to 2.5 ) and2 cm gauge graded approved hard stone ballast like granite, quartzite etc from dalla, jhansi or other quarries in proportion 1:1.5:3inlighter beams i.e. having span upto6m, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and t&p.csi no. 5.25 15 rcc work with cement, approved coarse sand ( f.m. 1.8 to 2.5 ) and2 cm gauge graded approved hard stone ballast like granite, quartzite etc from dalla, jhansi or other quarries in proportion 1:1.5:3in rcc t beam slab and column, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and t&p.csi no. 5.29 16 first class brick work in 1:6 cement and coarse sand ( f.m.1.8 to 2.5 ) mortar in foundation and plinth including supply of allmaterials, labour & t&p etc. required for proper completion of work.csi no. 6.01 17 1st class brick work in 1:6 c.m. with cement and coarse sand of 2.25 f.m. mortar in super structure including necessary cutting and moulding of brick as required including honey comb brick work, thickness of wall one brick ( 230mm ) thick in super structure. csi no. 6.01+6.07+6.08 18 same as item no. 17 above but for wall of half brick 4.5” ( 115 mm ) thick but in 1:6 c.m. with cement and coarse sand of 2.25 f.m. mortar. csi no. 6.01+6.07+6.09 19 brick work in foundation & plinth with old dismantledbricks ( supplied by department free of cost ) and coarse sand of f.m. 1.8 to 2.5mortar in 1:6 including supply of all other materials, labour, removing mortar & cleaning of old & used bricks, t&p etc complete. csi no. 6.18 20 same as in item 6.18 above butin super structure for 230 mm thick wall. csi no. 6.19 21 supply and filling brick bat in soak pit including all labour, material and t&p etc complete. ( for 01 soak pit ) . csi no. 6.23 22 2.5 cm. thick damp proof course of cement concrete consisting of 1 part cement 1.5 parts approved coarse sand ( f.m.1.8 to 2.5 ) , and3 parts approved 12 mm. graded stone grit and also including liquidwater proofing material as approved by the engineer incharge in the proportions specified by the manufacturer.csi no. 7.02 23 indian sal wood wrought framed and fixed including simple, mouldings straight work as in chaukhats including supply of allmaterials, labour and t&p etc.required for proper completion ofthe work. csi no. 8.03 24 country wood wrought framed and fixed including simple, mouldings straight work as in chaukhats including supply of allmaterials, labour and t&p etc.required for proper completion ofthe work. csi no. 8.04 25 additional cost for fixing glass panes with 4.5 cm. thick c.p.teak wood fully panelledincluding cost of materials, labour andt&petc. required for proper completion of the work. csi no. 8.08 26 supply and fixing stopper with rubber pad of chromium polished iron fitting with screws for doors and windows etc. csi no. 8.17 ( l ) ( as per old schedule 2020 21 ) 27 s / f of 25mm dia decorative curtain rod with decorative and caps, matching curtain rings, including fixing with necessary clamps, pvc gully, steel screws etc. complete.csi no. 8.19 ( as per old schedule 2020 21 ) 28 providing and fixing 19mm thick ply board / block board for wardrobe shutter etc. of reliance or scorpio or equivalent make including teak wood beading around the shutter and including fixing and adjustment of hinges, bolts handle and other fittings but excluding their supply and including cost of all material labour, t&p etc. required forthe proper completion of the work.csi no. 8.25 ( as per old schedule 2020 21 ) 29 providing and fixing of 25×10mm size tapered shape teak wood beading of approved design and fixing with nails and screw as directed by e / i including cost of all material labour, t&p etc. required forthe proper completion of the work. csi no. 8.26 ( as per old schedule 2020 21 ) 30 providing and placing 6 mm thick a.c. plain sheet in false ceiling in proper level and alignment complete.csi no. 8.29 ( as per old schedule 2020 21 ) 31 p / fof 6.0mm thick water proof commercialquality plywood in partition work to make 5x4mm size groove at specified intervals. ply shall be fixed by means of glue and headless nailsat 100mm c / c complete. cost including all labour, material, t&p required for proper completion of work. csi no. 8.30 ( as per old schedule 2020 21 ) 32 supply and fixing of 4.0 cm thick c.p teak wood door and window jali shutters withpanels of heavy quality galvanized iron wire mesh of size 14 x 24 withnecessary beading including supply and fixing of wooden cleats and stopsand including fixing and adjustment of hinges. but excluding supply of fixtures. csi no. 8.37 33 s / f galvanized mosquitos proof heavy quality iron wire gauge ( 14x24 ) over window frames and including supply of c.p. teak wood battens 8cm x 1cm. and including supply and fixing of necessary screws, all materials, labour andt&p etc. required for proper complete. csi no. 8.43 34 fixing of departmental doors & windows shutters including supply& fixing of hinges and other fixtures. ( excluding their supply ) including all materials, labour & t&p etc. required for proper completion of work.csi no. 8.51 35 p / f fully anodized aluminium fixed glazing with hindalco or equivalent extruded standard sections14gauge ( 2.41mm thick ) of various cross sections and joints mitred and jointed as shown in drawingincluding providing & fixing 5.5 mm thick toughened glass with neoprene beading & aluminium glazing clips all around. the minimum thickness of anodizing on all aluminiumsections should be 20 microns with a ( + ) 2 microns tolerance . the rate should include the cost of fixing the aluminum frame on teak wood frame or finished wall ( rb / rcc / masonry ) surface by means of 80 mm long approved counter sunk screws provided at 500 mm c / c or part there of starting from 100 mm above the bottom in vertical member and 100 mm from both the ends of horizontal top and bottom member excluding cost of teak frame but including cost of all other material, labour, tools & plants etc. complete. csi no. 8.52 36 same as above item no. 8.52 but for openable window portion as shown in drawings, including cost of aluminium hinges and all other fittings like concealed towerbolts handles etc of approved quality and including cost of all other material, labour, tools & plants etc. complete. csi no. 8.53 37 s / fixing of double action floor springs including cutting in floors / rcc slabs and grouting the same with c.c. & finishing the surface properly as and where required under aluminium doors as per direction of engineer in charge.including cost of all other material, labour, tools & plants etc. complete. csi no. 8.52 38 supply and fixing of 32 mm thick single leaf flush door shutter ( boiled water resistance, phenol maldehide resin bonded, hot pressed factory made ) commercial quality to i.s.2202 part 1 ( 1983 ) isi marked including fixing of wooden cleats and stoppers and including fixing and adjustment of hinges, bolts.locks, handles, springs and other fittings but excluding their supply including all materials, labour & t&p etc. required for proper completion of work. csi no. 8.54 39 supply and fixing brass polished hydraulic door closure of approved make & quality its fixing and adjustment with the help of screws, nuts and bolts including supply of all labour, t & p etc. required for proper completion of the work. csi no. 8.57 40 supplying & fixing 24 gauge annodized aluminium sheet of approved quality including cutting, wastage and fixing the same over the wooden door shutters with nails with all material, labour and t&p.csi no. 8.60 41 providing and fixing in place a full height storage cabinet 600 mm deep made with 19 mm thick isi marked ply borad, all interior surfaces to finished with pasting of 0.8 mm thick mica and all exterior surfaces to be finshed with pasting of 1 mm thick mica of texture and colour as approved by engineer in charge including all labour, t&p, other items like ( but not limited to ) fevicol, nails screws, higes, sliders, door handles, multipurpose lock of godrej or equivalent rate etc. required for proper completion of works, to be measured interms of front area only. csi no. 8.64 ( sor 22 23 ) 42 mild steel or iron work in heavy sizes such as trusses built upgates, door frames, record, racks roof work gates etc. wrought torequired form including holes rivetting or welding where necessary and also fixing in proper position and alignment including cost of all materials supplied by contractor.csi no. 9.01 43 as in item 9.01 above but when steel is to be provided by the department. csi no. 9.02 44 tmt / tor steel in plain work such as reinforced concrete orreinforced brick work ( when not included in an over all rates ) wrought to required shape as necessary including bending forproper completion of the work and including supply of steel its wastage, bend, hooks and authorized overlapping shall be measured. ( steel shall be arranged by the contractor ) . csi no. 9.03 45 supply and fixing rolling shutter of approved make made of ( 18×125 ) mm m.s. laths interlocked through their entire length and joint together at the end by end locks and mounted on specially designed pipe shaft with brackets side guides and arrangement for inside and outside locking with push and pull operation complete but excluding the cost of top cover and spring.csi no. 9.05 ( as per old schedule 2020 21 ) 46 supply and fixing galvanised mosquito proof jali ( 16x24 gauge ) withm.s. flat of 20 x 3 mm. size, on both sides screwed or welded to windowor door frame.csi no. 9.18 47 p / f in position collapsible steel shutter with vertical channels 20 x 10 x 2 mm. ( 3 / 4 x 3 / 8x 1 / 12 ) and braced with flat iron diagonals 20 x 5 mm. ( 3 / 4 x 3 / 16 ) size with top and bottom rails of tiron 40 x 40 x 6 mm. ( 1 / 2 x 1 1 / 2 x 1 / 4 ) with 38 mm dia steel pullys with bolts, nuts, nuts locking arrangement, stoppers, handles complete including applying a priming coat of approved red oxide paints.csi no. 9.29 48 p / f concertina coilfencing with required dia. 600 mm upto 3 m height of wall between existing angle iron ‘y’ shaped placed 2.4 m or 3.0 m apart and with 6 horizontal r.b.t. stud tied with g.i. staples and g.i. clips to retain horizontal including necessary bolts or g.i. barbed wire tied to angle iron all complete ( no. of rounds will be 7 to 8 in one meter length ) as per direction of engineer i / c with reinforced barbed tape ( r.b.t. ) / spring core ( 2.5mm thick ) wire of high tensile strength of 165 kg / sqmm with tape ( 0.52 mm thick ) of supreme make or equivalent and weight 43.478 gm / meter ( cost of ms angle, c.c. blocks shall be paid separately ) . csi no. 9.37 49 supply and fixing 24 b.w.g , g.c. iron sheet roofing .fixed in position with j or u bolts 10 mm. dia with g.i. limpet & bitumen washers including supply of all materials, labour, wastage. and t&p etc. required for proper completion of the work.csi no. 10.01 50 supply and fixing 6 mm thick grey corrugated asbestos sheet. including supply of all materials, labour, wastage. and t&p etc. required for proper completion of the work. csi no. 10.03 51 supply and laying one layer of tar felt or any other equivalent approved material at the junction of wall & roof or at any place as per direction of the engineer incharge including necessary overlap, applying a coat of approved mastic paint below the tar felt & including supply of all materials, labour and t&p etc. required for proper completion of the work.csi no. 10.06 52 providing and laying polythene sheet of approved quality in double layer of wt. 0.120 kg / sqm with 100 mm over lapping along roof slope as per direction of e / i complete.csi no. 10.08 ( as per old schedule 2020 21 ) 53 12 mm thick plaster with cement mortar consisting of one part of cement & three part of coarse sand ( 1:3 ) , minimum thickness not to be less then 10 mm including supply of all materiallabour and t&p etc for proper completion of work. csi no. 11.06 54 12 mm thick plaster with cement mortar consisting of one part of cement & four part of coarse sand ( 1:4 ) , minimum thickness not to be less then 10 mm including supply of all material, labour and t&p etc for proper completion of work. csi no. 11.07 55 12 mm thick plaster with cement mortar consisting of one part of cement & six part of coarse sand ( 1:6 ) , minimum thickness not to be less then 10 mm including supply of all material, labour and t&p etc for proper completion of work. csi no. 11.09 56 add for extra labour to all items of plaster if done in ceiling.csi no. 11.10 57 2 cm. thick cement plaster in dado or skirting in 1:2 consisting of onepart of cement and two parts of approved coarse sand laid inpanels finished with 3mm.floating coat of neat cement or cementand marble dust in ratio of 5:1 including supply of all materials, labour & t&p etc. required for proper completion of the work.csi no. 11.13 58 providing ( 12x15 ) mm section groove in plasterincluding all material, labour andt&p etc. required for proper completion of the work.csi no. 11.16 59 making drip coarse ( 25x12 ) mm in 1:2 cement and coarse sandincluding supply of all materials, labour and t&p etc requiredfor proper completion of work. csi no. 11.19 60 3 mm thick floating coat of neat cement finish including supply of all materials, labour and t&p etc. required for proper completion of the work. ( cement consumption 0.044 bag / sq.m. ) . csi no. 11.20 61 2.5 cm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and t&p etc, required for proper completion of the work. csi no. 12.02 62 4.0 cm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and t&p etc, required for proper completion of the work. without base cc. csi no. 12.04 63 first class bricks on edge floor laid dry, joints sand filled, including preparation of base to proper slope and its rammingincluding supply of all material labour & t&p etc. required forproper completion of the work. csi no. 12.07 64 same as in item 12.07 above but bricks laid flat.csi no. 12.08 65 supply and laying 6 mm thickglazed tiles in skirting / dado laid with1:3 cement and approved coarse sand mortar finished with whitecement slurry, jointing and polishing complete, including supplyof all materials, labour and t&p etc. completion required for proper completion of the work.csi no. 12.12 66 providing and fixing glass strips of 3.15 mm thickness & 25mm depth in jointsof floor and skirting at the time of laying floors, flush withfloor level including supply of all materials, labour& t&p etc.required for proper completion of work. csi no. 12.13 67 providing and fixing glass strips of 3.15 mm thickness & 40mm depth in jointsof floor and skirting at the time of laying floors, flush withfloor level including supply of all materials, labour& t&p etc. required for proper completion of work.csi no. 12.14 68 providing and fixing 18mm thick polished baroda green stone of approved shade and pattern in floor or on top of kitchen slab etc. laid with 1:3 cement and coarse sand mortar and jointing with white cement mixed with pigment to match the shade including supply of all material, labour and t&p etc. required for proper completion of work.csi no. 12.14 ( as per old schedule 2020 21 ) 69 providing and laying18mm. thickkotastonein flooring or skirtingoverbasecementmortar 1:4 mix and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete and including supply of all materials labour and t&p etc required for proper completion of the work.csi no. 12.17 70 providing and laying floor of 8 mm thick vitrifiedtiles in flooring or skirting of approved brand ( bell, johnson or equi. make ) size of 600x600 mmof approved shade, colour and pattern , laid over base cement mortar 1:4 mix including finishing the joints with white cementmixed with pigment to match the shade of tile including cost of all material, labour and t&p required for proper completion of the work.csi no. 12.18 71 providing and laying of 16 mm thick granite ( black / brown ) inflooring or skirting , of approved shade, colour, size and pattern , laid over base cement mortar 1:4 mix including finishing the joints with white cementmixed with pigment to match the shade of granite floor including cost of all material, labour and t&p required for proper completion of the work, as per direction of engineer incharge. csi no. 12.20 72 s / f 10mm thick group 25 acid resisting tiles of “somany” or equivalent approved make in flooring or skirting ( confirming to i.s. 4457 1967 ) in ordinary portland cement and coarse sand in ratio 1:3 with the joints filled with acid resistant cement “accocide” of a.c.c. or equivalent make acid resistant cement and liquid supplied with cement, mixed in 1:3 ratio to make a workable paste in g.i. tray. the joints should be kept as 5mm and to be cured for 7 days with dilute hcl ( one part acid and three parts of water ) . rate should be including the cost of all materials, labour and t&p etc. required for proper completion of the work.csi no. 12.22 73 supply of 80 mm thick i shaped mechanically compressed inter locking cement concrete paver block manufactured by high pressure & controlled vibration machine having plan dimension 200x ( 160+120 mm ) with minimum 5 mm thick toping of o.p.cement mixed with 25% marble powder. the compressive strength of concrete pavers blocks shall not be less than 30 mpa & 4.5 kg / no. including cost of all material, labour, t&p etc. required for proper completion of work as directed by engineer in charge but excluding g.s.t. which shall be paid extra as per rules.csi no. 12.23 74 painting or varnishing new iron work in small areas or new woodwork with one coat of ready mixed priming paint and one coat ofapproved superior quality ready mix paint luxol or equivalentbrand or varnish including supply of all materials, labour and t&p etc. required for proper completion of the work. paint to be used should conform to the i.s. 103 1950. csi no. 13.01 75 same as in item 13.01 above but for every coat after first coat.csi no. 13.02 76 same as in item 13.01 above but for every coat on previously paintedold wood or iron work including its sand papering, rubbing andcleaning as required, for proper completion of work. csi no. 13.03 77 one priming coat and one coat oil bound distemper on new work includingsupply of all materials, labour and t&p etc. required for propercompletion of the work. csi no. 13.08 78 same as in item 13.08 but for every coat after the first coat. csi no. 13.09 79 same as in item 13.08 but for every coat on previously old oil bound distemper surface. csi no. 13.10 80 applying p.o.p plaster with minimum 6mm to 10mm thick plaster of paris putty on plastered surface of walls / ceilings for smooth finish including its preparation of surface after applying oil based primer and chalk putty over p.o.p. rates including cost of all labour, material, t&p etc. required for proper completion of work. csi no. 13.16 ( as per old schedule 2020 21 ) 81 same as above item no. 13.16but making p.o. p. cornice 100mm×100mm size approved shape and design at junction of ceiling and wall including cost of necessary centering and shuttering p.o.p., its wastage, t&p etc. required for proper completion of work.csi no. 13.17 ( as per old schedule 2020 21 ) 82 making p.o.p. fan ring / circle on ceiling of room of approved shape and design approved by e / i including cost of all materials, labour t&p complete.csi no. 13.18 ( as per old schedule 2020 21 ) 83 applying birla or equivalent putty on new interior or exterior surface over one coat of water based cement primer of ici or equivalent brand for smoothening and levelling of the surface as per requirement and direction of engineer i / c including cost of all material, labour, t & p etc required for proper completion of work. csi no. 13.20 84 applying birla putty or equivalent putty on previousaly bila putty smoothen surface over one cost of water base cement primer of ici or equivalent brand for smoothining and leveling of the surface as per requirement and direction of e / i including cost of all material , labour and t&p required for proper completion of work. csi no. 13.21 85 painting one coat with apex or equivalent brand weather coat paint on new wall surfaces ( well prepared with birla putty and one coat of primer ici or equivalent which shall be paid separately ) including through washing with water including cost of all materials, labour, t&p required for proper completion of work.csi no. 13.22 86 same as in item no 13.22 above but for every coat of additional apex or equivalent brand weather coat paint. csi no. 13.23 87 same as in item 13.22 but for each coat ofapex or equivalent brand weather coat paint .on previously treated surface.csi no. 13.24 88 spirit polish over new wood work after rubbing down the surface, withsand paper to give smooth and shining surface including cost ofall materials, labour, t&p required for proper completion of thework. csi no. 13.29 89 spirit polish over previously polished wood surfaceafter rubbing down the surface, withsand paper to give smooth and shining surface including cost ofall materials, labour, t&p required for proper completion of thework.csi no. 13.30 90 white washing one coat including supply of all materials, labour and t&p etc. required for proper completion of the work.csi no. 14.01 91 white washing two coat including supply of all materials, labour and t&p etc. required for proper completion of the work.csi no. 14.02 92 colour washing one coat, using approved colouring material and colourincluding supply of all materials, labour and t&p etc. required for proper completion of the work.csi no. 14.04 93 same as in item 14.04 above but for each coat after the first coat. csi no. 14.05 94 dismantling brick work or stone work in lime or cement mortar andincluding stacking of materials as directed by theengineer in charge within a distance of 60 metres. csi no. 15.01 95 dismantling reinforced cement concrete or reinforced brick work, including stacking of dismantled materials as directed by theengineer incharge within a distance of 60 metres. csi no. 15.03 96 dismantling cement concrete or brick or granolithic floorsincluding base concrete and including stacking of dismantledmaterials as directed by the engineer in charge within a distanceof 60 metres. csi no. 15.05 97 dismantling doors or window leaves including stacking ofmaterials as directed by the engineer i / c within a dist. 60 m. csi no. 15.09 98 dismantaling doors and windowschowkhatsincluding stacking of materials as directed by engg in charge within a distance of 60 meters. csi no. 15.10 99 dismantling existing plaster including disposal of refuse asdirected by the engineer i / c within a distance of 60 m.csi no. 15.11 100 scrapping old white or colour wash or distemper including disposal of refuseas directed by the engineer i / c within a distance of 60 m.csi no. 15.12 101 cleaning of existing w.b.m. surface & laying premix 20mm thick over a tack coat with graded approved grit, heating the paint to the required temperature & mixing either in mixture or hand drums including cartage of mixture or hand drums and, maintenance of side patries and watering them during operation and including supply of all materials, labour and t&p etc. required for proper completion of the work.csi no. 18.07 102 same as in item no. 18.07 above but in laying premix 4.0 cm thick.csi no. 18.08 103 laying seal coat with 6 mm size graded stone grit and bitumen including heating the bitumen paint to required temperature including cartage and cost of materials, labour, t&p etc. required for propercompletion of work.csi no. 18.09 104 boring with 150 mm dia casing pipe to a probable depth of 60 m from ground level with skilled and unskilled labour including all t&p and boring apparatus and supervision charges etc, required for proper completion of the work for submersible pump set.csi no. 18.41 ( as per old schedule 2020 21 ) 105 extraction of casing pipe 150mm. dia after completion of lowering of pipe assembly including all labour and t & p etc. complete.csi no. 18.42 ( as per old schedule 2020 21 ) 106 providing110mm dia plain pvc casing pipes ( aroma / supreme ) ( pressure10 kg. / sqcm. ) for making tubewell assembly and cartage to boring site, including cost of all labour, materials and t&p required for assembly making and proper completion of work.csi no. 19.08 107 edging with bricks laid dry lengthwise including excavation, refilling, consolidating with hand packing and spreading neatly surplus earth with in a lead of 50 m 75 class designation 1 fps bricks. csi no. 19.09 ( as per old schedule 2020 21 ) 108 providing 110mm dia slotted pvc casing pipes ( aroma / supreme ) ( pressure10 kg. / sqcm. ) for making tubewell assembly and cartage to boring site, including cost of all labour, materials and t&p required for assembly making and proper completion of work. csi no. 19.10 109 supply and plantation of following tree: ( a ) polyalthia pendula ( ashoka pendula ) / cut sagaun / ficus etc of height 100 150 cm. csi no. 19.11 ( a ) ( as per old schedule 2020 21 ) 110 same in item no. 19.11 ( a ) above but for ( b ) cassia fistula ( amaltash ) / delonix regia ( gulmouhar ) / bauhina purpurea ( kachnaar ) / mimusops elengi ( maulsri ) / shisham / neem etc. of height 100 150 cm. csi no. 19.11 ( b ) ( as per old schedule 2020 21 ) 111 supply & installation ofsubmersible pump of k.s.b / calama. or eqt. make including cost of labour, t&p and material required for completion of work. ( b ) 1.5 hp outlet 40mm dia. or more, head 71 / 36, discharge 2000 / 6000 lph csi no. 19.32 ( b ) 112 same as item no. 19.32 ( b ) but for ( e ) three phase 5 hp outlet 50 mm dia. or more, head 60 / 24, discharge 9000 / 24000 lphcsi no. 19.32 ( e ) 113 same as item no. 19.32 ( b ) but for ( h ) three phase 15 hp outlet 80 mm dia. or more, head 57 / 28, discharge 30000 / 65000 lphcsi no. 19.32 ( h ) 114 supply & installation of electrical control panel of l&t / havells or equivalent make for submersible pump / pumpset containing contractor relay condenser. ( b ) for 1.5 / 2 h.p pump set single phase.csi no. 19.31 ( b ) 115 renewing panes of 4.8 to 5.7 mm glass including supply of glass with putty and brads including supply of all materials, labour and t&p etc. required for proper completion of the work. ( a ) glass of 4 mm thick. csi no. 20.04 ( b ) 116 cleaning of septic tank including disposal of waste out side the uppcl area as per direction of the engineer in charge including cost of all labour, t&p etc.required for proper completion of the work. csi no. 20.12 117 same as in item no.20.12 above but for inspection chamber.csi no. 20.13 118 cleaning of main drain or width more than 300 mm.including disposal of waste refuses sludge out side the boards area including washing and cleaning by clean water completely as per direction of the engineer in charge including cost of all labour, t&p etc.required for proper completion of the work. csi no. 20.14 119 same as above in item no. 20.14 but for drain of width less than 300 mm. csi no. 20.15 120 supply and replacing of following chromium polished iron fittings including cost of nuts, bolts etc.complete.csi no. 20.17 ( a ) 121 same as item no. 20.17 ( a ) above but for ( b ) tower bolts 10 mm dia x 250 mm long.csi no. 20.17 ( b ) 122 same as item no. 20.17 ( a ) above but for ( d ) iron hinges 100 mm size.12 gauge.thick.csi no. 20.17 ( d ) 123 same as item no. 20.17 ( a ) above but for ( f ) m.s.handles 100 mm size.csi no. 20.17 ( f ) 124 leveling and dressing of land by cuttingfilling and upto 150 mm. depth complete with all labour, t&p etc. required for proper completion of the work.csi no. 20.18 125 cleaning and opening of chocked w.c. / bath / kithchen pipe line including opening and refixing of chamber cover including washing etc. complete. ( analysis based on nbo 11 25.020. csi no. 20.19 126 opening, cleaning, overhauling, oiling and greasing of defective rolling shutter and also re setting of its springs for its smooth functioning including cost of all materials, labour and t&p etc. ( approx. size of shutter 2x2.5 ) . csi no. 20.20 127 polishing of marble floor by cleaning with carborandum stone after washing with tartre cleaning powder etc. and finally with french mansion polish including supply of all materials, labour and t&p etc. required for proper completion of the work.csi no. 20.22 128 extraction of defective vt submersible pumps and motor with 60 x 90 column pipe and then lowering of the repaired pump and motor with pipe and testing the same including checking main cut out fuse and operation of tube well for 24 hours fo rits smooth working with all cost of materials, labour and t&p etc required for the proper completion of the work.csi no. 20.28 129 supply and mixing bleaching powder in over head tank as required or as directed by engineer in charge.csi no. 20.29 130 dismantling and resoling brick on edge / interlocking tile floor with existing old bricks / tile laid dry joints filled with sand including preparation of base to proper slope and camber, its ramming including supply of labour, t&p etc. ( labour only ) csi no. 22.03 ( as per old schedule 2020 21 ) 131 supply and laying 1.5sq.mm gauge copper wire of plaza orequivalent make of approved quality including connecting withexisting wiring in existingp.v.c.pipe. including allmaterials, labour and t&p complete.csi no. 22.06 ( a ) 132 supply and laying 2.5sq.mm gauge copper wire of plaza orequivalent make of approved quality including connecting withexisting wiring in existingp.v.c.pipe. including allmaterials, labour and t&p complete.csi no. 22.06 ( b ) 133 supply and laying 4.0sq.mm gauge copper wire of plaza orequivalent make of approved quality including connecting withexisting wiring in existingp.v.c.pipe. including allmaterials, labour and t&p complete.csi no. 22.06 ( c ) 134 supply and laying 6.0sq.mm gauge copper wire of plaza orequivalent make of approved quality including connecting withexisting wiring in existingp.v.c.pipe. including allmaterials, labour and t&p complete.csi no. 22.06 ( d ) 135 rewinding of burnt ceiling fan with approved copper wire including cost of all materials, labour and t&p etc. complete ( burnt wirewill not be taken back. ) . csi no. 22.08 136 providing and fixing 12 mm thick shuttering ply by replacing of panels including detaching the shutters, opening out and separating the frame members and panels and including reassembling the shutter in part and again re fixing the shutter including cost of all material, labour and t&p etc. required for proper completion of the work. csi no. 22.09 ( as per old schedule 2020 21 ) 137 replacing and fixing new galvanized mosquito proof heavy quality iron wire mesh ( 16×24 ) gauge over door / window with old beading and including supply and fixing necessary screws / nails and all material, labour and t&p etc. required for proper completion of the work.csi no. 22.10 ( as per old schedule 2020 21 ) 138 painting and printing house number on residence in circle of size 200 mm dia including preparation of base with enamel paint complete as directed by e / i including cost of all materials, labour and t&p etc. required for proper completion of work. csi no. 22.17 ( as per old schedule 2020 21 ) 139 printing name and designation of occupants in a plate of size ( 200×150 ) mm dia including preparation of the base with best quality synthetic enamel paint as directed by e / i including cost of all materials, labour and t&p etc. required for proper completion of work.csi no. 22.18 ( as per old schedule 2020 21 ) 140 supply and sprinkling of lime in all drains of colony and waterlogged area including cost of all labour, materials, and t&p etc, as required for proper completion of the work.csi no. 22.19 141 cleaning and sweeping of roof of residence as and when requiredincluding uprooting of rank vegetation and disposal of thegarbage upto 50 m. csi no. 22.20 142 cleaning of roads and their side patteries includingsweeping, removing garbage and vegetation from patteries, if anyand and its disposal to dust bins. csi no. 22.21 143 s / rstep type of regulator for ceiling fan of gecor equivalent make of approved quality including cost of all labour material, t&p etc. required for proper completion of the work.csi no. 22.60 ( b ) ( as per old schedule 2020 21 ) 144 s / r of element of geyser 1500 watts 250 volt including taking out damage element and refitting and testing including cost of all labour material, t&p etc. required for proper completion of the work.csi no. 22.65 ( as per old schedule 2020 21 ) 145 operation of tube well by a suitable experienced operator continuously or in different intervals as per schedule fixed by e / i including opening and closing valves, greasing of motor, changing of fuse wire etc. as required for proper running of tube well. csi no. 22.69 ( as per old schedule 2020 21 ) 146 repair of starter for 10 h.p. to 25 h.p. electric motor including its disconnection and opening out, checking & changing of its, coil, minor parts such as nuts, screws, washers, damaged contacts, etc, and its perfect setting, re fixing and testing for its smooth and normal working etc, including cost of all labour material, t&p etc. required for proper completion of the work. csi no. 22.73 ( as per old schedule 2020 21 ) 147 s / r of 10 sqm pvc flat 3 core cable suitable up to 25 hp submerssible motor of finolex / atlas or equivalent make of approved quality including cost of all labour material, t&p etc. required for proper completion of the workcsi no. 22.91 ( as per old schedule 2020 21 ) 148 s / r 63 amp, 415 volt of isi mark rewireable switch porciline fuse unit ( cut out ) ofssk or equivalent make including removing of old unit and reconnection, including cost of all labour material, t&p etc. required for proper completion of the work. csi no. 22.93 ( b ) ( as per old schedule 2020 21 ) 149 s / r of set of main contact of starter up to 25 hp motor l&t make including cost of all labour material, t&p etc. required for proper completion of the work. csi no. 22.95 ( as per old schedule 2020 21 ) 150 hiring charge of welding machine for 8 hours service in a day or part as per requirement for attending miner type welding work as and where required as per direction of e / i. csi no. 22.101 ( as per old schedule 2020 21 ) 151 providing hard rubber beading at bottom of door covered with aluminium strips for restoration of air conditioning and prolection from rats etc, as per direction of engineer in charge including cost of materials labour and t&p etc, required for proper completion of work.csi no. 22.108 ( as per old schedule 2020 21 ) 152 s / f of 24 gauge aluminium sheet of approved quality including cutting, wastage, fixing the same over wooden door shutters by nails including cost of all materials, labour and t&p etc.csi no. 22.113 ( as per old schedule 2020 21 ) 153 opening of aluminium door shutters and refixing the same after replacement of new rubber beading and screws complete excluding cost of al, pipe and glass but including cost rubber beading and screws. cost including all labour, materials and t&p etc, required for proper completion of work.csi no. 22.116 ( as per old schedule 2020 21 ) 154 maintenance of seasonal flower bed including digging the earth inbed ( minimum depth of bed 30 cm ) as per necessity whenevernecessary during replantation, plantation of seasonal flower, manuring, watering, mixing of manure with earth uprooting the expired plants after its expiry and replacement of the new seasonal plants like its seeds including cost of chaukidar, work assistant and miss. works as per directed by engg in charge ( cost of manure, good earth and sand mixture and its spreading shall be paidseparately ) and including fertilizers, pesticides and medicines etc complete. csi no. 23.03 ( a ) 155 same as item no.23.03 ( a ) but for permanentplants. csi no. 23.03 ( b ) 156 supply and stacking of compost manure at site including carriageupto 3 km ( manure measured in stacks will be reduced by 8% forpayment ) . csi no. 23.04 157 supply and plantation of approved 2 years old plants duly plantedin earthen gamla of approximate size 300x 300 mm nominal size, filled with compost manure and sand mixed in approved proportionincluding cost of approved quality earthen gamla, compost manure, sand all other materials, labour and t&p etc reqd. for proper completion of work. csi no. 23.08 158 supply and planting seasonal flower plants such as genda, rose, ostar, flox, guldawadi, gulmehndi, cochia etc. including digging hole of proper size, manure and treatment with proper chemical etc., including cost of fertilizer, manure, all materials, labour and t&p etc complete in allrespects. csi no. 23.10 159 supply and planting permanent ornamental plant like croten, varil pristal, glodulus, lily, fern, bogenbelia etc. including cost of plants, manure, pesticides, fertilizer, labour and t&p etc complete also including preparation of flower bed. csi no. 23.11 160 supply and plantingashoka, pendula, mango, neem, peepal, sheesham etc in pits including cost of all materials, labour and t&p etc complete in all respects. ( cost of digging pitshall be paid separetely as per item no. 23.08 ) . csi no. 23.12 161 supply and planting of garden grass ( australian ) . including cost of plants, manure, pesticides, fertilizer, labour and t&p etc complete also including preparation of bed. csi no. 23.14 162 arranging one mali for maintenance of lawn & plants, including cost of mali, required t&p and other miscellaneous work as per direction of engineer i / c.csi no. 23.15 163 hedge plantation in a row distance between two hedge 15 to 25 cm including digging hole 6” to 12” , manure and treatment with proper chemical etc., including cost of all materials, labour and t&p etc complete in all respects.csi no. 23.16 164 wiring point for light with 1.5 sq. mm. fr pvc insulated multistrand single copper conductor cable in pvc conduit pipe concealed in the wall, 14 swg copper pvc coated earth continuity wire, and approved quality, piano type switch ceiling rose / angle / batten holder as per approved sample on 3mm thick phenolic laminated bakelite sheet etc. of matching shade with wall colour complete in all respect. psi no. 121 ( b ) 165 wiring point for fan / fresh air fan ( light duty exhaust fan ) 1.5 sq. mm fr pvc insulated multistrand single core copper conductor cable pvc conduit pipe concealed in the wall, 14 swg copperearth continuity wire and approved quality, piano type switch & ceiling rose as per approved sample on 3mm thick phenolic laminated backelite sheet etc. of matching shade with wall colour complete in all respects as per direction of e / i. psi no. 123 ( b ) 166 wiring point for plug with 1.5 sq. mm fr pvc insulated multistrand single core copper conductor cable in pvc conduit pipe concealed in the wall 14 swg copper earth continuity wire and approved quality type switch and socket as per approved sample etc. of matching shade with wall colour complete in all repects as per direction of e / ipsi no. 124 ( b ) 167 supply and burring of safe earthing electrode t 39 cu copper coated, length 2000mm outer pipe 76.3mmx3.2 inner pipe 42.4mm x2.6mm terminal dia 12mm, coating 80 100 micron filled with crystalline property with 50 kgs activated soil ( bfc ) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm squre c.i. frame with hinged cover & massory housing. ( from electrode terminal to switch board, cost of 25x3 copper strip will be extra.psi no. 727 ( c ) 168 supply and fixing of power plug with 15a / 240v v flush type switch and 5 pin 15a / 250v flush type universal socket in suitable m.s. box of 175mmx 100mmx50mm size with phenolic laminated bakelite sheet cover 3mm thick fixed with brass machine screw and cup washer.csi no. 21.20 ( as per old schedule 2020 21 ) 169 s / r of bakelite angle holder of ssk or equivalent make of approved quality including cost of all labour material, t&p etc. required for proper completion of the work. csi no. 22.51 ( as per old schedule 2020 21 ) 170 s / r of piano type switch 6 amp 250 volt of havells or equivalent make of approved quality including cost of all labour material, t&p etc. required for proper completion of the work. ( a ) without framecsi no. 22.52 ( a ) ( as per old schedule 2020 21 ) 171 s / r socket 2 / 3 pin 6 amp 250 volt of havells or equivalent make of approved quality by e / i. including cost of all labour material, t&p etc. required for proper completion of the work. ( a ) without frame csi no. 22.53 ( a ) ( as per old schedule 2020 21 ) 172 add extra for using 12mm long c.p. brass heavy quality 15 mm dia extension nipple for bib / stop cock etc complete. csi no. 24.27 ( a ) ( as per old schedule 2020 21 ) 173 providing and fixing 80 / 100 mm dia c.i. d jonit with ring rubber packing nut, bolt and washer etc. complete as per direction of e / i. csi no. 24.50 ( as per old schedule 2020 21 ) 174 providing and fixing jet with pipe heavy quality including supply of all material, labour and t&p etc. required for proper completion of the work.csi no. 24.54 ( as per old schedule 2020 21 ) 175 providing and fixing glass shelf 7 / 32” ( 5.50mm ) thick of 600 mm × 130 mm size with c.p. brass guard rail of standard size and brackets fixed to wooden cleats with c.p. brass screws including supply of all materials, labourand t&p etc. required for proper completion of work .csi no. 25.22 ( as per old schedule 2020 21 ) 176 providing and fixing 15 mm dia b class jindal, jtc, isi marked g.i. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed gi fitting where required, cutting and making good the walls etc and all materials, labour and t&p complete.csi no. 26.01 ( a ) 177 same as item no. 26.01 ( a ) but for 20 mm dia.csi no. 26.01 ( b ) 178 same as item no. 26.01 ( a ) but for 25 mm dia.csi no. 26.01 ( c ) 179 same as item no. 26.01 ( a ) but for 32 mm dia.csi no. 26.01 ( d ) 180 same as item no. 26.01 ( a ) but for 40 mm dia.csi no. 26.01 ( e ) 181 same as item no. 26.01 ( a ) but for 100 mm dia.csi no. 26.01 ( i ) 182 providing & fixing half turn 15mm dia gate valve, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. csi no. 26.05 ( a ) 183 providing & fixing half turn 20mm dia gate valve, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work.csi no. 26.05 ( b ) 184 providing and fixing pvc ball float valve 15 mm dia. with brass & union complete, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. csi no. 26.06 ( a ) 185 providing and fixing pvc connection pipe, 450x15 with 2 brass units isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work.csi no. 26.09 ( b ) 186 p / f gi unions nominal bore 15 mm, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. csi no. 26.10 ( a ) 187 p / f gi unions 20 mm nominal bore, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work.csi no. 26.10 ( b ) 188 supply and fixing of syntex or equivalent make water storage tank including all materials, labours, t&p etc required for proper completion of work. csi no. 26.12 189 providing a.c. box with mcb, anchor / havells or equivalent make as per direction of e / i.csi no. 26.13 ( as per old schedule 2020 21 ) 190 p / fbrass bib cock, 15 mm dia ( 400 gsm ) isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. csi no. 26.13 ( a ) 191 same as item no. 26.13 ( a ) but for supply and fixing of 15 mm dia ci / pvc bib cock including replacing of old bibcock complete. csi no. 26.13 ( c ) 192 providing & installation of 5kva voltage stablizer of ( 110v 280v ) rating with copper wiring of blue bird or its equivalent price brand.the rate are inclusive of cartage, manpower, t&p etc required to complete the work in all respect.csi no. 26.16 ( as per old schedule 2020 21 ) 193 providing and fixing cp brass bib cock15 mm dia. heavy quality ( 400gm ) ( l & k and equi. ) fittings, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. csi no. 26.16 ( a ) 194 providing and fixing cp brass shower heavy quality ( > 225 gms ) fittings, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. csi no. 26.16 ( e ) 195 providing and fixing cp brass wash basin mixer heavy quality ( l & k and equi. ) fittings, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. csi no. 26.16 ( f ) 196 providing and fixingcp brass wall mixerheavy quality ( l & k and equi. ) fittings, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. csi no. 26.16 ( g ) 197 providing and fixingc.p.brass telephonic shower heavy quality ( l & k and equi. ) fittings, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. csi no. 26.16 ( h ) 198 providing and fixingcp brass angle valve heavy quality ( l&k or equi. ) fittings, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. csi no. 26.16 ( i ) 199 providing and fixingcp brass piller cock heavy quality ( l&k or equi. ) fittings, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. csi no. 26.16 ( j ) 200 providing and fixingconcealed stop cock heavy quality ( l&k or equi. ) fittings, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. csi no. 26.16 ( k ) 201 providing and fixing of 110 mm dia pvc pipe 6 kg / sq.cm forwith special such as tee, bend, socket, elbow etc including supply of all labour, material, t & p etc complete required for proper completion of work.csi no. 26.17 202 providing and fixing 15 mm dia isi approved cpvcpipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed gi fitting where required, cutting and making good the walls etc and all materials, labour and t&p complete. csi no. 26.19 203 providing and fixing 20 mm dia isi approved cpvcpipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed gi fitting where required, cutting and making good the walls etc and all materials, labour and t&p complete. csi no. 26.20 204 providing and fixing 25 mm dia isi approved cpvcpipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed gi fitting where required, cutting and making good the walls etc and all materials, labour and t&p complete. csi no. 26.21 205 s / f high tensile steel colour coated anti rust, high temp resistant sheet with tensile strength 550 pma hot dip metallic ( zinc aluminium ) alloy ( zn 55% ) al, ( 45% ) coating 70 gsm with total thickness not less than 0.50 mm ( tct ) durashine or equivalent make with necessary over lops incl s / f galvamized j / v hook with bolts, nuts, washer and bitumen washers etc. incl, cost of material, labour t&p etcincluding cost of material, labour t&p etc, required for proper completion of work as per direction of e / i confirming a.s. 1397:199. csi no. 26.60 ( as per old schedule 2020 21 ) 206 providing and fixing first quality white glazed orissa pattern w.c.pan hindustan, cera make. size 580 mm. ( hindustan, cera make ) with out p trapincluding supply of all materials, labour and t&p etc.complete.csi no. 27.01 207 same as in item no. 27.01 but of european type. csi no. 27.02 208 providing and fixing plastic seat covercomplete with plastic lid for european type wc isi markedincluding supply of all materials, labour and t&p etc.complete. csi no. 27.04 209 providing and fixing flat back 430x370x340 mm . size lipped front urinal basin of white glazed earthern ware first quality ( hindutan, neycer make ) i.s.i. marked including supply of all materials, labour and t&p etc. required for proper completion of the work. csi no. 27.06 210 providing and fixing 550x400 mm wash hand basin of white glazed earthern ware first quality i.s.i. marked ( hindustan, neycer / cera make ) including supply of all materials, labour and t&p etc. required for proper completion of the work. csi no. 27.08 211 same as in item 27.08 above but when wash hand basin of size 450x300 mm size is used. .csi no. 27.10 212 providing and fixing 10 litres low level pvc flushing cistern, complete with all fittings including supply of all materials, labour and t&p etc. required for proper completion of the work.csi no. 27.12 213 providing and fixing in position 32 mm. dia p.v.c. flush pipe. for w.c. with unions, bends etc. including supply of all materials, labour and t&p etc.required for proper completion of the work. csi no. 27.13 214 providing and fixing in position 32 mm. dia p.v.c.waste pipe for wash basin. including supply of all materials, labour and t&p etc.required for proper completion of the work. csi no. 27.14 215 providing and fixing 600 mm x 450 mm beveled edge mirror of atul, kiran makeglass with indian polish 6.50 mm thick complete with back of 600 mm x 450 mm x 6 mm hard board sheet fixed to wooden cieats with c.p. brass screws and washers including supply of all materials, labour and t&p etc.required for proper completion of the work.csi no. 27.15 216 providing and fixing 750 mm x 20 mm size c.p. brass towel rail of approved qualityincluding bracketsincluding supply of all materials, labour and t&p etc. required for proper completion of the work and cutting and making good the wall plaster etc. required for work.csi no. 27.16 217 providing and fixing soap dish chromium plated with brackets fixed to wooden cleats with brass screws including supply of all materials, labour and t&p etc.required for proper completion of the work.csi no. 27.19 218 supply and fixing 100 mm.pvc trap india make of heavy approved quality complete with ci grating, includingsupply of all materials, labour and t&p etc. required for proper completion of the work. csi no. 27.21 ( b ) 219 providing and fixing 100 mm dia white glazed p or s trap including cement concrete and all materials, labour cartage t&p etc.required for proper completion of the work. ( for w.c. ) .csi no. 27.23 220 providing and fixing stainless steel sink 610x450x200 mm heavy quality ( isi marked ) includingall materials, labour cartage t&p etc.required for proper completion of the work.csi no. 27.26 221 providing and laying75 mm dia.swr, pvc ( finolex or equivalent ) pipe including cost of excavation, c.c etc including its jointing and connection, all materials, labour and t&p etc. required for proper completion of the work.csi no. 27.29 ( a ) 222 same as in item 27.29 ( a ) above but for 90 mm dia.csi no. 27.29 ( b ) 223 same as in item 27.29 ( a ) above but for 110 mm dia.csi no. 27.29 ( c ) 224 providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. granite work.csi no. 28.19 225 providing and laying water proofing treatment in sunken portion of wcs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : ( a ) first layer of slurry of cement @ 0.488 kg / sqm mixed with water proofing cement compound @ 0.253 kg / sqm. this layer will be allowed to air cure for 4 hours. ( b ) second layer of slurry of cement @ 0.242 kg / sqm mixed with water proofing cement compound @ 0.126 kg / sqm. this layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. the rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. csi no. 28.26 226 providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: ( a ) applying a slurry coat of neat cement using 2.75 kg / sqm of cement admixed with water proofing compound conforming to is. 2645 and approved by engineer in charge over the rcc slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. ( b ) laying brick bats with mortar using broken bricks / brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 ( 1 cement : 5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineerin charge over 20 mm thick layer of cement mortar of mix 1:5 ( 1 cement :5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. ( c ) after two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge. ( d ) finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 ( 1 cement :4 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. ( e ) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“all above operations to be done in order and as directed and specified by the engineer in charge :with average thickness of 120 mm and minimum thickness at khurra as 65 mm. csi no. 28.28 227 providing and fixing false ceiling at all heights with integral densifiedr armstrong false ceiling tiles of size 595x595 x12 mm of approved texture, design and patterns having nrc ( noise reduction coefficient ) of 0.50 ( minimum ) as per is 8225:1987, light reflectance of 85% ( minimum ) . non combustible as per bs:476 ( part 4 ) , fire performance as perbs:476 ( part 6 &7 ) , humidity resistance of 100%, thermal conductivity < 0.043 w / m k as per astm 518:1991, in true horizontal level suspended on interlocking metal powder coated t grid of hot dipped galvanised iron section of 0.40 mm thick on silhouette profile, rotary stiched double webbed white with 6 sub head : 26 new technologies and materials 1632 mm reveal profilewhite / black ) , comprising of main t runners of size 15x42 mm of length 3000 mm, cross t of size 15x42 mm of length 1200 mm and secondary intermediate cross t of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items ( galvanizing @ 80 grams per sqm ) i.e. 50 mm long, 8 mm outer diameter m 6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and l shape level adjuster of size 85x25x2 mm. galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall s.s screws. the work shall be carried out as per specifications, drawing and as per directions of the engineer in charge. 26.23.1 with 12 mm thick armstrong miniralfobre sound absorbing sheetcsi no. 28.30 228 providing and fixingacp in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . ( cost of aluminium snap beading shall be paid in basic item ) : with acpof 4.0 mm thickness. csi no. 28.31 229 supply and fixing of 5 blade exhaust fan ventile air dx 225 mm of havellsor equivalent make including all material, t&p etc required for proper completion of work as approved by engineer in charge.csi no. 28.38 230 rewinding of 15 h.p sub merssiblemotor with 2.10sqmm. pvc insulated copper wire of finolex or equivalent make as per approved sample including cost of winding wire and pvc insulated sheet etc, including dismantling of sub mersible motor from pump and column pipe and taking out burnt copper wire from its slots and cleaning of slots with sand paper and rewinding including cost of its testing up to 24 hrs and guarantee for 6 months for its smooth and normal working including all cost of material, labour and t&p etc, required for proper completion of work. ( burnt copper wire cost is adjusted in given rate and shall be the properly of contractor.nsi 231 p / f openable steel glazed windows and ventilators of standard rolled z section conforming to is 7452 1974 and welded with ( 100×20×5 ) mm holdfast embedded in c.c. block ( 23×11.5×7.5 ) cm size of 1:2:4 proportion of cement, coarse sand, & 20mm graded stone ballast as per drawing etc. complete but excluding s / f of glass panes of 4mm thick with nuts glazing clips with special putty of approved make etc. the fabrication should conform to is 1038 1975. including cost of all materials, labour & t&p etc. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 232 same as item no. 230 abovebut for fixed portion. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 233 providing and fixing ist qaulity one piece european type white glazed floor mounted seat isi maked size 695x385x700mm as per approved sample including 10 lit capacity white glazed seat mounted air pressure with flushing cistern plastic seat cover with plastic lid c.p brass hings and rubber buffers with 15mm dia pvc connection 600mm long including supply all material labour t&p etc required for proper completion of the work. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 234 supply and fixing ist quality cera make white glazed wash hand basin with pedestal size ( 650x515x240 ) mm including its fixing with all labour & t&p etc. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 235 supply and fixing ist quality jaguar make 15mm dia c.p brass central hole basin sensor faucet ( model no. 51011 ) battery oprated includingits fixing with all labour & t&p. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 236 s / f best quality bamboo stick incl. with iron wire and fixing through fastener incl. all labour t&p etc. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 237 finishing of walls with three coats water proof exterior emulsion paint “ace” “out look” or equivalent make on new work including one priming coat ( 1 liter paint diluted including 0.75 liter of water ) to give an even shade complete including cost of all materials, labour and t&p etc, as per direction of e / i. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 238 two coat of ace on previously old treated surface on exterior walls. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 239 change thermo state and element in havells 11 fin electric oil filled radiator room heater 2900 w with all labour & t&p. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 240 s / r of brass spendil with washer of approved quality and make for bib / stop / pillar cock. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 241 s / r of syphone system of pvc cistern including all material, labour and t&p etc. complete. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 242 s / r of pvc tank cover of 500 200 liter tank including locking arrangement etc. complete. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 243 s / f of pvc handle of pvc cistern of approved quality etc. including all material, labour and t&p etc. complete. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 244 supply and fixing 1200mm size sweepceiling fan ( g.e.c. / polar / crompton / usha or equivalent approved make ) with double ball bearing, step type electronic regulator, necessary wire and 900 mm long hanging rod with double canopy etc. including testing and commissioning as per direction of engineer in charge. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 245 s / f soap dispenser make ist quality transparent vessel and c.p. brass nozel use for filling hand wash liquid including fixing. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 246 p / f 3mm thick fiber sheet including its cutting and fixing. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 247 supply and fixing ist qualty door loock rectangular and round shape including its fixing. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 248 supply and fixing stainless steel plate robe hook, 8 long including its fixing.nsi 249 hiring charges of hydra machine with fuel & driver for lifting, removing & disposal at proper place of fallen huge trees in campus at hydel colony victoria park, meerut including all labour & t&p etc required for completion of work as instructedby e / i. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 250 supply & fixing 1.5 h.p. submersible starter contact relay including its fixing. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 251 supply & fixing 15mm dia p.v.c. flexible pipe for uses in garden & plants water supply. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 252 supply & fixing 20mm dia p.v.c. flexible pipe for uses in garden & plants water supply. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 253 providing and lowering of 50mm dia p.v.c. flexible pipe make with coupling socket etc including cutting the pipe of required length and fixing including cost of all materials labour and t&p. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 254 service of 15 kva generator including changing all filters, oil, petty parts with all labour & t&p. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 255 supply and fixing 2mm thick transparent polythene heavy quality including its cutting of required size and fixing with 25mm long metro screw with all labour and t&p. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 256 supply and fixing m.s 16mm dia 150mlong anchor bolt fixing with hammer drill machine with all labour and t&p. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 257 supply and harrison cx 3000 0557 stainless steel 11 leaves pad lock with 3 key. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 258 supply of plastic body 12 lit capacity pedal dustbin with removal garbage bag. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 259 supply and fixing jaguar make 5 lit capacity wall mount cistern including its fixing with all labour and t&p. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 260 supply and fixing 200mm dia 26 watt circular led light with adaptor in lift including its fixing charge. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 261 supply and fixing 15mm dia c.p brass alton grace make 2 in 01 wall mixer with 40m long c.p brass extension pices including its fixing with all labour and t&p. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 262 repair of grass cutting machine including motor binding supply new blade, supply new condenser with all labour and t&p. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 263 supply and installation luminous rc 25000 200 ah tubular battery including its installation charge. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 264 supply of 2000w bajaj make blower with two heat setting and auto thermal cut out. ( rate already sanction by agr. no. 07 / 2020 21 ) nsi 265 supply and fixing of u.p.v.c 80mm dia 11 kg / cm2 coloumn pipes aashirvad make with coloumn coupling socket as required for proper completion of work including all labour material &t&p. ( rate already sanction by agr. no. 18 / 2022 23 ) nsi 266 roof treatment work with 2mm thick dr. fixit urpwith cement salary and fiber glass mesh 1mm thick ist coat urp and cement mixer ratio ( 1:1.5 ) on properly cleaned roofsurface and laying fiber glass cloths after once again 1mm thick 2nd coat urp and cement mixer in ratio ( 1:1.5 ) including all labour & t&p. ( already sanction by s.e ( c ) vide om. no. 779 / ecdc / mt / wt 1 dt. 01.07.2022 ) nsi 267 making & fixing flex board size ( 5x4 ) with 25mmx25mm light weight hollow pipe frame including writting as per required metter with all labour & t&p. ( rate already sanction by agr. no. 18 / 2022 23 ) nsi 268 supply and fixing 10mm dia supporting cable for support 15 h.p submersible pump in loweringincluding all labour & t&p. ( rate already sanction by agr. no. 18 / 2022 23 ) nsi 269 supply and fixing 10mm dia supporting cable for support 15 h.p submersible pump in loweringincluding all labour & t&p. ( rate already sanction by agr. no. 18 / 2022 23 ) nsi 270 supply and fixing 24 watt led tube light phillips, havells and equvalent make including its fixing & t&p. ( rate already sanction by agr. no. 18 / 2022 23 ) nsi 271 supply and fixing of under water flood light, recess mounting suitable for & with 50 watt lamp confirming to ip 68 protection including its installation. ( rate already sanction by s.e ( c ) vide o.m no. 472 / ecdc / mt / wt 1 dt. 20.04.2022 ) nsi 272 supply and fixing 9 watt led bulb bajaj, havells, phillips & equivalent make of approved quality by e / i including cost of all labour material & t&p etc. ( rate already sanction by agr. no. 18 / 2022 23 ) nsi 273 supply and fixing 15 amp 250 volt, socket of havells, anchor or equivalent make of approved quality by e / i including cost of all labour material & t&p etc. ( rate already sanction by agr. no. 18 / 2022 23 ) nsi 274 supply and fixing 15 amp 250 volt, socket of havells, anchor or equivalent make of approved quality by e / i including cost of all labour material & t&p etc. ( rate already sanction by agr. no. 18 / 2022 23 ) nsi 275 supply and fixing havells make 63 amp four pole change over including its fixing with all labour & t&p etc. ( rate already sanction by agr. no. 18 / 2022 23 ) nsi 276 supply and fixing door bell of anchor or equivalent make of approved quality by e / i including cost of all labour material & t&p etc. ( rate already sanction by agr. no. 18 / 2022 23 ) nsi 277 supply and fixing 12 watt led bulb bajaj, havells, phillips make of approved quality by e / i including cost of all labour material & t&p etc. ( rate already sanction by agr. no. 18 / 2022 23 ) nsi 278 supply and fixing acp sheet name plate with night refleted material including writing required name & degigration including its fixing. ( rate already sanction by agr. no. 18 / 2022 23 ) nsi 279 supply and fixing call bell of anchor or equivalent make of approved quality by e / i including cost of all labour material & t&p etc. ( rate already sanction by agr. no. 18 / 2022 23 ) nsi 280 engaging of carpenter for petty works of site etc. as per direction e / i.based on. csi no. 1.10 281 engaging of plumber for petty works of site etc. as per direction e / i.based on. csi no. 1.15 282 engaging of belder / majdoor for petty works of site etc. as per direction e / i.based on. csi no. 1.20 283 engaging of electrician with kit for petty repair of electrical works, etc. as per direction of e / ibased on. csi no. 1.36 284 circuit wiring / submain wiring:circuit wiring starting from distribution boxto point control box / switch box inpvc ( heavy ) 25mm dia conduits, using accessories such as bends, tees, saddles, draw boxes, mounting boxes, inner plates, cover plates, ceiling rose etc. ( including chase cutting & filling of chase where ever required ) with pvc insulated 1100v grade fr multi stranded copper conductor wire ( color code to be used ) . identification ferrules at both end to be provided.circuit wiring using 2 runs of 2.5 sq.mm+ 1 run of 1.5sqmm pvc insulated copper wire drawn in25mm dia 2 mm thick pvc conduits as lighting circuits being reckoned from distribution board to first light / fan control switch boards psi no. 1307 ( c ) up pwd sor 2009 285 circuit wiring using 2 runs of 4.0 sq.mm+ 1 run of 2.5 sqmm pvc insulated copper wire drawn in25mm dia 2 mm thick pvc conduitspower circuits being reckoned from distribution board to first power control switch boards. ( for power points 15 amp ) psi no. 221 ( c ) 286 circuit wiring using 2 runs of 6.0 sq.mm+ 1 run of 4.0 sqmm pvc insulated copper wire drawn in25mm dia 2 mm thick pvc conduits aspower circuits being reckoned from distribution board to first power control switch boards. ( for a.c. ) psi no. 222 ( c ) 287 supply and wiring of submain with two number 10 sqmm pvc insulated 1100 v grade single core aluminium conductor cable in 25mm dia heavy guage rigid steel conduit partly concealed in wall and partly laid in slab along with reinforcement before concerting with one number 8 swg gi earth continuity wire including matching colour wash etc complete in all respect.psi no. 123 288 supply and fixing 6a to 32a sp mcbc curve 10 ka psi no. 1002 289 d ) 63 amp. isolator psi no. 1005 ( b ) 290 surface flush mounted 8 ways s.p.n. distribution board.psi no. 1024...
39618685 work of 11 kv / lt line / vcb / transformer construction / installation in edsd – iv amanpur in the edd ( rural ) kasganj under the juridiction of edc, kasganj on semi turn key basis. 2 stone pad 3 f bracket 4 pg clamp for dog 5 stay rod complete 6 earthing rod complete 7 danger board 8 gi pipe 6 dia 9 cabel jointing kit 33 / 11 kv 3x / 300 sqmm i / d & o / d 10 cabel jointing kit 11 kv 3x185 sqmm id / & o / d 11 t off channel 12 clamp for lt ( t off ) with n / b 13 m.s. cross brassing angel 14 ms top channel 15 nut bolt & washer 16 cabel jointing kit 11 kv 3x120 sqmm id / & o / d 17 alluminimum winding wire 06 s.w.g. 18 guarding wire 06 s.w.g. 19 battery charger 24 volt 20 battery set 24 volt 21 guarding wire 08 s.w.g. 22 lt protection unit ( tail less unit ) 23 d / p clamp with n / b 24 33 kv post insulator 25 160 mm o / d pn 4 pe 80 grade uvstblised hdpe pipe 26 11 kv tpmo complete 27 number of plate 28 red oxide paint 29 alluminimum paint 30 guarding angel with nut & bolt 31 guarding clamp 32 33 kv lightening arrester set 33 33 kv ct 200 / 100 / 1 1 1a 34 33 kv pt 35 m.s. dropper channel 36 holding clamp for top channel 37 holding clamp with nut bolt 38 lt incoming pannel with metering equipment & fixing arrangement ( ls ) 39 copperl piece 50x225x10mm ( ls ) 40 copperl piece 62x225x12mm ( ls ) 41 lt pvc cable al. 3.5x400 sqmm. 42 al. leg long barrel, off size ( ls ) 43 4 core lt mcb with box ( ls ) 44 danger board barbed wire including jumper 45 erection of material 46 erection & fabrication of structure with all material for 33 kv line isolator. 47 erection & fabrication of structure with all material for 33 kv bus insulator. 48 installation of 33 kv lightening arresters. 49 fixing / erection of lt protection unit ( tail less unit ) 50 installation & erection of 33 kvcontrol pannel fort / f 51 installation & fixing battery charger 24 volt & battery set 24 volt 52 erection / installation of 33 kv vcb outdoor 800 a 53 erection of 11 kv vcb outgoing ctr 200 / 100 / 5a 350 mva 54 erection / installation of 11 kv vcb incoming ctr 600 / 300 / 5a / 10a 350 mva 24 volt 55 installation of 33 kv post insulator 56 installation of 11 kv / 33 / 11 kv jointing kit outdoors 3x120 / 3x185 / 3x300 sq mm. 57 earthing of 100 / 250 / 400 kvat / f body & neutral in all respect. 58 laying & fixing hdpe pipeunder ground through hdd method 59 laying & fixing of 11 kv xlpe cable 3x185 / 300 sqmm. 60 erection of single support including complete h.t / l.t fittings s.t. pole 11 mtr. sp 55 including earthing, grouting & muffing of pole. 61 erection of single support including complete h.t / l.t fittings pcc pole 8.5 mtrincluding earthing, grouting & muffing of pole. 62 erection of double pcc pole 8.5 mtr support including complete h.t / l.t fittings pcc pole 8.5 mtrincluding earthing, grouting & muffing of pole. 63 fixing of danger board 64 fixing of danger board barbed wire including jumper 65 erection of double pole on s.t. pole including the work of complete lines.t. pole 11 mtr. sp 55including earthing, grouting & muffing of pole. 66 fixing of 11 kv tpmo set complete 67 erection of stay set complete including the work of nuzzling etc. 68 laying sagging stringing, binding and jumpering acsr weasel conductor 69 laying sagging stringing, binding and jumpering acsr dog conductor 70 laying & fixing of lt pvc cable 3.5x400 sqmm. 71 painting of st pole with red oxide & ailunimum paintas per respo norms 72 laying & fixing of guarding wire 06 / 08 swg 73 carriage from store & installation of 100 kva / 63 kva / 25 kvat / f 11 / 0.4 kva new in all respect 74 installationoflt incoming pannel with metering equipment & fixing arragement ( ls ) 75 carriage from store & installation of 250 kvat / f 11 / 0.4 kv new & making the plinthin all respect 76 making / installation of plinth for 250 / 400 kva / other t / fin all respect. 77 making / installation of fencing for 250 / 400 kva / other t / fin all respect. 78 earthing of 100 / 250 / 400 kva & above distrubutiont / f body & neutral in all respect. 79 installation of fancing of 250 kvat / f 11 / 0.4 kv new in all respect 80 connecting ht cabel connection from 33 kv side & 11 kv side of 10 mva power transformer 81 water level earthing by boring and lowering of g.i. pipe size 40 mm dia & thickness 2 mm into the ground at 20 mtr depth or upto the water level with the lower end of solid copper cone approx 225 mm long and 750 gm in weight shall be provided and screwed in pipe as well as bringing out a continuous copper wire 6 swg from the cone up to the ground surface where it will be bolted to the m.s. earth strip for transformer body & neutral connection, the earth strip will be welded to the g.i. pipe and neutral earthing support. all required material provided / supply by the contractor own his cost. 82 making of m.s. angle ladder type frame of angle ( 75x75x8mm ) & gi strip ( 50x6mm ) near power transformer for power cable with concreting of the same in the ground and proper clamping ( 50x6mm ) of the same with transformer cable. 83 making of m.s. angle frame of ( 75x75x8mm ) in l shape to connect t / f neutral by flexible copper strip including cost of copper strip & wll be connected to newly constructed well type earthing for power t / f neutral as per respo norms. 84 ertection / installation of 33 kv ct 200 / 100 / 1 1 1a 85 ertection / installation of 33 kv pt 86 underground railwaycrossingpermission fees 87 charges for dismantling work: work includes dismantling from site and cartage of same materails from site / location to central store / any other place as per instruction of je / sdo / ee concerned. 88 11 kv vcb incoming ctr 600 / 300 / 10a 89 11 kv vcb outgoing ctr 200 / 100 / 5a 90 11 / 0.4 kv 25 / 100 / 160 kva t / f old...
39577331 work of construction and strengthening of 33 kv line under power distribution division ii, orai, capacity increase of 33 / 11 kv power sub station and other work related to the sub station. work of construction and strengthening of 11 kv line, installation of 11 / 0.4 kb distribution transformers and work of increasing the capacity, in which the amount will be paid as per requirement by the executing agency. 1 commissioning ofthe whole following work including carriage, commissioning with all required material as per resspo norms. please read the boq carefully then quote the rates. 2 abc bunch 3x120 3 m.s t off channel 4 11 kv pin with nut 5 33 kv pin with nut 6 11 kv disc & fitting 7 energization of 100 kva t/f with all fitting as per resspo norms. 8 energization of 250 kva t/f with all fitting as per resspo norms. 9 energization of 400 kva t/f with all fitting as per resspo norms. 10 base angle t/f 11 stay complete 12 earthing complete 13 tpmo 14 11 kv fuse set 15 33 kv fuse set 16 stp 11 m with earthing, grouting & concreating of support & stay as per resspo norms. 17 pcc 8.5 m with earthing, grouting & concreating of support & stay as per resspo norms. 18 11 kv f clamp 19 11 kv x arm with clamp 20 weasel conductor 21 33 kv control panel single t/f 22 dcp al winding wire 23 33 kv ct 24 33 kv pt outdoor 25 outdoor switchyard 26 33 kv vcb with all fitting 27 11 kv vcb i/c with all fitting 28 11 kv vcb o/g with all fitting 29 energization of 10 mva t/f with all fitting as per resspo norms. 30 11 kv 3x300 xlpe cable 31 h/s cable j kit 3x300 mm o/d for 33 kv 32 h/s cable j kit 3x300 mm i/d for 33 kv 33 cable box 3x185 mm i/d for 33 kv 34 cable box 3x240 mm i/d for 33 kv 35 in the works related to 33/11 kv power substation, all the old materials (power t/f, 11/0.4 kv t/f, 33 and 11 kv cables, steel scrap, conductors, ct/pt, vcb, control panel etc.) will be dismantled by the contractor and the old dismantled material will be taken from the pit site and deposited in the store. 36 clearing of the line route by cutting of tree branches during erection of line and also upto the time of energisation of site incharge ...
39577312 under power distribution division ii, orai, 33 / 11 kv power substation capacity increase and other substation related works, 11 kv line construction and strengthening work. 11 / 0.4 work of installation and expansion of kg distribution transformers in which all types of clamps, nuts bolts, stone pads, number plates, lugs are supplied as per requirement by the executing organization. 1 commissioning ofthe whole following work including carriage, commissioning with all required material as per resspo norms. please read the boq carefully then quote the rates. 2 earthing complete 3 33 kv tpmo 4 33 kv fuse set 5 lighting arrestor 6 33 kv control panel single t/f 7 dcp al winding wire 8 33 kv ct with all fitting 9 33 kv pt outdoor with all fitting 10 outdoor switchyard 11 33 kv vcb with all fitting 12 11 kv vcb i/c with all fitting 13 11 kv vcb o/g with all fitting 14 energization of 10 mva t/f with all fitting including earthing 15 11 kv 3x300 xlpe cable 16 33 kv control panel single t/f 17 h/s cable j kit 3x185 mm i/d for 11 kv 18 h/s cable j kit 3x185 mm o/d for 11 kv 19 h/s cable j kit 3x300 mm i/d for 33 kv 20 h/s cable j kit 3x300 mm o/d for 33 kv 21 cable box 3x185 mm i/d for 11 kv 22 cable box 3x240 mm i/d for 11 kv 23 gi pipe 2.5 dia 24 gi pipe 2.5 strip 25 gi pipe clamp 26 gi pipe socket 27 ms earthing rod 40 dia 28 gi pipe cap 29 gi lug 30 in the works related to 33/11 kv power substation, all the old materials (power t/f, 11/0.4 kv t/f, 33 and 11 kv cables, steel scrap, conductors, ct/pt, vcb, control panel etc.) will be dismantled by the contractor and the old dismantled material will be taken from the pit site and deposited in the store. 31 clearing of the line route by cutting of tree branches during erection of line and also upto the time of energisation of site incharge ...
39506363 tender for supply of super enameled alu. winding wire of different sizes super enameled alu. winding wire of different sizes (grade ii, class 130) , se aluminium wire 21.00 swg (grade ii, class 130) , se aluminium wire 20.00 swg (grade ii, class 130) , se aluminium wire 17.50 swg (grade ii, class 130) , se aluminium wire 16.50 swg (grade ii, class 130) , se aluminium wire 14.50 swg (grade ii, class 130) , se aluminium wire 13.00 swg (grade ii, class 130)...
39466476 processing & conversion of old damaged / burnt copper coils into etp grade ( is 191 part vth 1980 / any latest amendment ) d.p.c. & super enamled copper winding wire & l.t. strip. 1 processing & conversion of old damaged / burnt copper coils1.02 mm. super enameled cu. coil, 2.30 mm. / above size of dpc copper wire & l.t. strip into etp grade ( is 191 part vth 1980 / any latest amendment ) d.p.c. copper winding wire as per required sizes. 2 processing & conversion of old damaged / burnt copper coils1.02 mm. super enameled cu. coil, 2.30 mm. / above size of dpc copper wire & l.t. strip into etp grade ( is 191 part vth 1980 / any latest amendment ) d.p.c. copper l.t. strip as per required sizes....
39368503 supply of dual coated enamelled copper winding wire size 19 swg [ 1.000 mm ] confirming to is:13730 part 13 grade of covering shall be grade 2 [ medium covering ] . [ warranty period: 30 months after the date of delivery ] => limited...
39361037 tender for construction of rain water harvesting system; 1 rain water harvesting system 2 excavation in foundation in ordinary soil including lift upto 1.50m and lead upto 30m and including filling watring and ramming of excavated earth into the trenchess or into the space between the building and the side of foundation trenchess or into the plinth and removal and disposal of surplush earth as directedby the engineer in charge upto a distance of 30m from the foundation trenchess for foundation. 3 concrete with 4 cm gauge brick ballast fine sand of 1.25 fm and cement in proportion of 8:4:1 in foundations and under floors, including supply of all materials, labour, tools & plants etc required for proper completion of the work. 4 m 150 brick work in 1:4 ( one cement and four fine sand of 1.25 fm ) mortar in foundation and plinth including supply of all material labour t&p etc. required for proper completion of the work. 5 12 mm thick plaster with cement & fine sand of 1.25 fm in 1:4 over brick work minimum thickness not to be less than 1 cm including supply of all material labour t&p etc. required for proper completion of the work. 6 2.5 cm ( 1” ) thick 1:2:4 plain cement concrete floor with cement approved coarse sand and 2 cm. ( 1” ) graded approved stone grit, laid in panels finished with 3 mm. ( 1 / 8” ) floating coat of neat cement of cement and marble dust in ratio 5:1 as specified without base concrete and removing any overlapping mortar at the joints of the penal if any and giving them a uniform finish including supply of all material labour t&p etc. required for proper completion of the work. 7 r.c.c.work with cement approved coarse sand and 2 cm gauge approved stone grit.in proportion of 1:2:4 in slabs excluding supply of reinforcement and its bending but including its fixing and bindings the same with 24bwg.c.i. binding wire and including necessary centering and shuttering etc. and supply of all materials labour t & p etc. requiredfor proper completion of work including cost of winding wire. 8 m.s. ( tor steel or plain ) in plain work such as r.c.c. or r.b. work including bending for proper shape and excluding supply of steel and also including authorised overlapping shall be measured and including cost of binding wire. ( labour rate only ) 9 supply and filling bolder 100 150 mm including all labour t& p with all cartage etc. 5.00×4.00×0.30 = 6.00 m3 say 6.00 m3 10 same as item no. 08 but boulder size 50 60mm..... 5.00×4.00×0.30 = 6.00 m3 say 6.00 m3 11 same as item no. 08 but boulder size 20 30mm.....5.00×4.00×0.15 = 3.00 m3 say 3.00 m3 12 same as item no. 08 but boulder size 6 10mm..... 5.00×4.00×0.05 = 1.00 m3 say 1.00 m3 13 providing and laying cement concrete blcok size ( 400×100×100 ) mm in proportion of 1:2:4 in water storage tank flooring including all materials labour and t &p etc. required for proper completion of the work. area of water storage tank 5.00×4.00= 20.00 m2 area of one block 0.40×0.10 = 0.04 m2no of block 20.00 / 0.04= 500 nos 14 providing and laying 8’ dia with 6” pvc pipe including cost of all materials labor t&p etc. cost of two bore ( i ) drilling of two bore 2×190 ft @ 60 / feet 15 ( ii ) cost of pvc pipe 6” 2×140 feet @ 150 / feet 16 ( iii ) cost of jali 2×40 feet @ 150 / feet 17 ( iv ) cost of cloth for jail 2 nos. size @ 3000 / nos 18 ( v ) cost of development of lone 2×10 hr. @ 500 / hr 19 ( vi ) cost of p gravel 2×8 m3 = 16 m3@ 4000 / m3...
39361036 construction of shed store, scrap & lab for distillery construction of shed store, scrap & lab for distillery 2 m.s. work in heavy sizes includingtrusses, built up gates, door frames etc. including cost of welding rod, gas, drilling of holes and also higher charges of welding machine, labor, t& p etc. but excluding cost of ms steel. ( steel shall be provided by mill free of cost ) only labor rate 3 fixing of gci sheets from roof with screw and between washer / ruber washer / joru hook but excluding cost of gci sheets ( only labour rate ) required for proper completion of the work. 4 excavation in foundation in ordinary soil including lift upto 1.50m and lead upto 30m and including filling watering and ramming of excavated earth into the trenchess or into the space between the building and the side of foundation trenchess or into the plinth and removal and disposal of surplush earth as directedby the engineer in charge upto a distance of 30m from the foundation trenchess for foundation 5 cement concrete with 4cm gauge approved stone ballast coarse sand and cement in the proportion of 1:4:8 including s / o all materials labour t &p etc. required for proper completion of the work. 6 r.c.c.work with cement approved coarse sand and 2 cm gauge approved stone grit.in proportion of 1:2:4 in r.c.c. foundation excluding supply of reinforcement and its bending but including its fixing and bindings the same with 24bwg.c.i. binding wire and including necessary centering and shuttering etc. and supply of all materials labour t & p etc. requiredfor proper completion of work including cost of winding wire...
39035269 bids are invited for copper winding wire 0.965 mm , copper winding wire 0.863 mm , copper winding wire 0.762 mm , copper winding wire 0.660 mm total quantity : 74...
39020131 bids are invited for measurement tape , flex of rally decoration , pedestal fan , winding wire , chuna 40 kg , count board , wiper , broom , phenyl , harpic total quantity : 70...
38672368 auction sale of scrap copper burnt wire, copper coil, winding wire and other copper wire of sort and sizes. the approx metal content is as under copper 99%, tape warnish insulation cotton dust etc 1% note loading by purchaser. location: lying in godown b, near pole k...
38479962 bids are invited for copper winding wire 0.965 mm , copper winding wire 0.863 mm , copper winding wire 0.762 mm , copper winding wire 0.660 mm total quantity : 74...
38448734 processing and conversion of old damaged/ burnt copper coils into etp grade (is 191 part vth 1980/any latest amendment) dpc copper winding wire and dpc copper strips as per required sizes...
38405551 tender for for double paper recovering of copper winding wire and strip of damaged transformer coil at various workshop under ewc, agra...
38404714 tender for 21 swg super enamewl aluminium winding wire....
38390508 tender for alteration of dpc copper winding wire and dpc copper strip....
38346961 bids are invited for t b assembly as per drawing no 27183501207, var 00 (q3) , t b assembly as per drawing no 27183501207, var 01 (q3) , hand lamp with holder and 20 mtr wire (q3) , free weeling diode type by 127 (q3) , hylum plate 3tk x 125 x 125 lg to drg no. 47189101004 (q3) , pop revet size 34 (one packet should contain 500 nos revet) (q3) , gi locking wire(winding wire) dia 1.4 mm (q3) , chain assly (for dee shackle) to drg no 37193804000. var 00 (q3) total quantity : 11485...
38286616 bids are invited for winding wire total quantity : 383...
38266833 1. rewinding of 15hp submersible pump set with suitable size winding wire including winding charges. ( main building gate no.2 ) 2. rewinding of 2hp mono block pump ( at conservatory ) with suitable size of copper wire including rewinding charges.3. s / f of l&t make 15hp star delta starter with auto unit & single phasing preventer with all labour t / p etc. required for proper completion of work ( at nirala nagar csir colony ) .4. repairing of l&t & bch make starter by changing of relay, auto unit, contector & coil at tagore marg & nirala nagar csir colony.5. s / f of 6 dia sluice valve behind cpmb parking pump house including repairing of leakage in pipeline.6. s / f of 4dia sluice valve with nuts bolts rubber packing all labour tp required for proper completion of work at nbri main building pump house near parking area => limited...
38198833 auction sale of waste equipment burnt pvc winding wire, gun metal scrap, ms scrap....
38192948 auction sale of burnt pvc winding wire, gun metal scrap, ms scrap....
38183616 competitive ebidding for supply of general electrical items season 2023 24 , empire tape ¾” size. , do but 1” size. , pvc insulating tape steel grip bhore makes ¾” size. , glass varnish tape ¾” ( 50mm ) size. , do but 1” size. , phase tester “taparia” make. , heater element best quality isi marked 1000 watt. , do but 1500 watt. , do but 2000 watt. , cotton tape 1” size.50 mtr.roll , ctc 300 grams. bottle bharat bijli make. , do 400. –do , thinner 218 for above varnish. , dr. beck make varnish elmoluft 1 a. , megger 0 500 motwani make. , pvc batten ½” size. , do but ¾” size. , do but 1” size. , do but 1 1 / 4” size. , pvc gittiesof above sizes / any sizes , p.t. holder 60 watt. anchor / ssk / lica makes. , do but 100 watt. , s.c. holder 100 watt. jyoti make. , do but 300 / 500 watt. jyoti make. , flush type switches 5 amp. lica / anchor make , do but 15 amp.“ “ , 3 pin combined switch socket of 5amp. lica / anchor make. , do but 15 amp. , 3 pin plug top 5amp. lica / anchor make. , do but 15 amp. , button holder. , angle holder lica / anchor make , ceiling rose. , novex paper 7 and 10 mil.minimax make , do but 5 mil. , crc 2 26 in 400gm. packing imported. , do but bharat bijli make. , copper bus bar. , kit kat completes 32 amp. 240volt. , aluminium / copper lugs “dowells” make. ( please quote maximum discount on co.price list. , taparia make screw driver ¼”x6” size. , do but 5 / 16”x8” size. , do but 3 / 8” x 10” size. , pedestal type amp. mtr. in 4” dia 0 10 amp. , do but 0 20 amp. , do but 0 30 amp. , do but 0 40 amp. , do but 0 50 amp. , do but 0 60 amp. , vidyut make pvc insulated unsheathed wire copper conductor wires any sizes / cores on principal manufacturer prevailing price list. ( discount ) . , htp / atlas make different swg enamelled winding wires made of copper conforming to is13730 on co.prevailing price list discount. , bakalite sheet isi standard ¼” size. , do but ½” size. , do but ¾” size. , leathorised paper 5 miles. , do but 7 miles. , do but 10 miles. , capacitor 300kva oil filled javik make one capacitor 25kvar. , dowels paste tube. , insulating pliers tap aria make 8” , screw driver 10”x 3 / 8” , do but 12”x ½” , carbon brush holder 170hp , copper carbon brush / bush 22x32x40 for 250hp , do but for 400 hp , carbon brush 22x32x40 for 150hp , pure carbon bush 40x40x20 , proximity switches pnp 24vd , m.t.c. coils 220volt. , micro switch , semi conductors fuse 500amp.660volt. , m.c.b. 32 amp. havel’s / standard make.as per list less , pvc wire aluminum weather proof 2 core x 4m sq. plaza make. list less , dcr thruster 604se 1616. , carbon brush holder for 1.5mw jyoti alternator. , aluminum socket 35sq.mm , multi standard annealed tinned copper conductor ( seven std. ) pvc ( type e self ext. type ) insulated cores, two / three over all screened with allayer tape along with a drain with of 7 / 0.3mm of atc inner pvc ( type stj ) shielded, g.i. wire armored and overall pvc type stj fr ) sheathed cable: , a. copper shielded armored cable 6 core x 1.00mm sq. , b. –do but 4 core x 1.00mm sq. , c. –do but 2 core x 1.00mm sq. , push button station 1 no + 1 nc vaishno make , carbon brushes 50x40x20mm size. , hrc fuse link type 63amp. ee make. , carbon brush holder for 250h.p. motor.frame no tr 6 , cooling fan for centrifugal machine 6”, 2900rpm, 230v , pure carbon for cane unloaded 100x20x20mm size. , m 15e carbon brushes 20x40x40mm size. , fuse carrier bakelite 63amp. vaishnav make. , limit switch essen make 1 no + 1 nc , limit switch element eussion make 1 no + 1 nc , motor connection lead eussion 40 hp 16mm²glass braided , carbon brush for hand grinder dewalt makes. , slip ring 12.5hp crompton makes. , carbon brush holder 12.5hp , mushroom type push button with element. , carbon brush holder for 100hp electric motor. , grandly make pvc flat unarmored copper cable 3 core x 50sq. mm for unloader. , electronic control card for 50hp dynodrive eddy control make. , timer ( single mode ) 5 second 60 / 120 second bch makepc. , m.c.b. 25 amps. 4 pole 440volt havel’s make.as per list less , cradle terminal for 4000amp. acb.& jaw , fix bakelite for above. , slip ring assembly for 60hp / 250hp motor. , slip ring holder. small size 10hp motor , brassholder for 250hp motor. , techno generator dtg 4000 70 ma / 200v, 4000 rpm frame no tr 6 , semi conductor fuses 700amp. 690 v 3 str / 110 bushman denmark make. , copper carbon bushes 45x15x15mm size. , changeover switches 32amp. 240volt ben tax make. , semi conductor fuses500 amp.690v buss man , copper carbons brush 30x16x40mm size. , pvc copper cable 1.5sq. mm x 4 core. , jaw contacts 3200 amp. for acb l&t make. , do but 4000amp. , do but 1000amp. , techno generator required for 100hp dynodrive bore 75mm outside dia 200mm crompton greaves / eddy control make. , moving contact fbc 250amp.l&t make , do but fbc 400amp.l&t make , synchronous timer em 1000, 2 relay, 240volt 2no + 2 nc, 0 120 second. , carbon brush holder for 400hp slip ring , techogenerator 100v 1000rpm tdp 02 lt 3 hubner make. , carbon brush good quality 22x32x45mm size. , do but 20x38x42mm size. , carbon brush holder for 150hp , fuse carrier bakelite 63 / 32amp. , varnish insulating tape 1” size. , bectol red varnishes dr. beck. , bectol gray varnish dr. beck , all type ampere meter volt meter hour k.w.h. meter “automatic electric bombay. list less , all switch dp & tp switch standard makep on ppl list less , spare of switch fa / fac / fbc l&t make ppl list less. , moving copper contact for 250 a 500 v siemans make , do 400 a 500v siemens make , do 630a 500v siemans make , fix copper contact 250 a 500 vsiemens make , do 400a 500v siemens make , do 630 a 500 v siemens make , black tape 3 / 4 johanson make , do but 1 , multimeter fluke / me co , pvc scathed aluminium coonducto to wire all size as per price list , do copper conductor as per price list , pvc motor coding fan 3hp, 5hp, 10hp, 25 hp, 40hp...
38175453 procurement of fg copper under 3 months rate contract procurement of fgc opper conductor , double glass lapped polyesterimide varnish bonded rectangular copper winding wire to aa28113 rev03 and annexture a rev 00. 61 to 90 sq mm ( bare ) => limited...
38164875 auction sale of unserviceable scrap consists of submersible copper winding wire, copper pvc winding wire for submersible motor pumps, poly wrapped submersible wires of copper, and pvc insulated 3 core flexible copper wires & cables, 3 core flat or round cable, multi or single core wires such as 0.5, 1.0, 1.5, 2.0 and 2.5 sq mm etc. pvc content could be about 48 %and copper could be about 52 %. in various sorts of sizes. this scrap contains a variety of additional copper cables, both known and unknown. this is not appropriate for railway. appliedmoef condition.location: inside godown no. 91 / 06lbpl, dbaw, gst 18%, tcs 1% , hsn code 740400, allocation 20714208, moef condition will be applicable...
38038938 supply of dual coated enamelled copper winding wire size 19 swg [ 1.000 mm ] confirming to is:13730 part 13 grade of covering shall be grade 2 [ medium covering ] . [ warranty period: 30 months after the date of delivery ] => limited...