Urban Development Department - Uttar Pradesh

34207566 bids are invited for electrification work 1 supply & fixing of 9 mtr gi octagonal pole of approved make ( top dia 70mm, bottom dia 155 mm and base plate 12mm thik ) having 3mm thikness with single arm bracket ( 1 mtr length ) on rcc foundation including the cost of foundation, foundation bolts, excavation & back filling and required t&p completee in all respect. 2 supply and fixing of led street light fitting having die cast aluminium body and diffuser with driver set suitable for 110 to 130 watt. confirming to ip 66 protection complete in all respect. 3 supply and laying of aluminium conductor pvc insulated armoured served sheathed cables 1100 volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top.16 sq. mm 4 core 4 supply and fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn, complete in all respect. 5 supply and fixing of 80mm gi pipe for the protection of cable during road crossing parallel to road 6 supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. the armouring of the cable shall be properly connected with the earth as per direction of engineer incharge. 7 supply and fixing of pole fuse boxes with kit kat etc. complete in all respect. 8 s / b safe earthing electrode t 39 cu coated length upto 3000mm outer 76.3mm x 3.2mm inner pipe 42.4mm x 2.6mm for making suitable with crystalline conduvtive misture complete...

Urban Development Department - Uttar Pradesh

34173539 bids are invited for led street light 90 watt , led street light 60 watt , single arm bracket , d clamps of 50 mm x 5 mm , d clamps of 50 mm x 6 mm , 10 sq. mm 4 core power cable , 2 core 6 mm power cable , 2 core 10 mm power cable , shackle insulator , eletrification work control panel , 32 amp change over switch , 63 amp changeover switch , contractor , time switch , bed switch , tape , led flood light , xlpe cable for working voltages upto andincluding 1.1 kv is 7098 ( part 1 ) ( q2 ) total quantity : 6678...

Urban Development Department - Uttar Pradesh

33937054 bids are invited for xlpe cable for working voltages upto and including 1.1 kv is 7098 ( part 1 ) ( q2 ) , led street light 90 watt , led street light 60 watt , single arm bracket , d clamps of 50 mm x 5 mm , d clamps of 50 mm x 6 mm , 10 sq. mm 4 core power cable , 2 core 6 mm power cable , 2 core 10 mm powercable , shackle insulator , control panel , 32 amp changeover switch , 63 amp change over switch , contractor , time switch , bed switch , tape , led flood light total quantity : 6678...

Urban Development Department - Uttar Pradesh

33300786 bids are invited for item no 01 s/f of 10 mtr gi octagonal pole of approved make (top dia 100mm, bottom dia 200mm and base plate 16mm thik) having 3 mm thikness with single arm bracket etc complete as per estimate item no 02 supply & fixing of led street light fitting with madatory driver set dicast alluminium body and lences sutaible for 75watt to 140 150 watt and confirming ip 66 protection baving company logo infraved complete in all including labour with five year warranty. s.r no. 1425 item no 03 digging trouch 45 cm dept for cable including cc road cutting. item no 04 supply of 4x16 sq mm alluminum armard cable (s.i. no 501) item no 05 supply of 4x16 sq mm hdep 50mm dia. item no 06 supply and wiring of submain with two number 2.5 sq mm flash pvc insulated 1100 v grade muistrand single core copper conductor cable s.i. no 1301(a) 148 item no 07 laying of 4x16 sq mm armard cable with help of gi pipe 50mm dia blew the ground level after axcavation back filling including all labour. item no 08 supply& fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn, complete in all respect si no 807 (f) (ii) item no 09 writing and numbering work on pole as directed by ei/c. item no 10 supply & fixing of 3 strip radium sticker on pole for night visiblty etc all comp. item no 11 supply and fixing of crimping, solderless, copper tin electroplated lugs of dowells/ismail make suitable for 1.5 sq. mm to 2.5 sq. mm cables, including tapping with insulating tape, complete in all respect s.i. no 1129 item no 12 supply and burying of safe earthing eectrode t 19, (hot dip galvanized), length up to 3000 mm outer dia 50 mm inner dia 25mm, terminal dia 12mm, outer gi pipe of 16 swg and inner gi pipe of 12 swg with hot dip galvanization up to 100 mixture (cmm) having anti corrosive & condutive property with 50 kgs activeted soil (bfc) capable ofreducing the soil resistivity with good mixture of retaining capacity and one earthing lead of 25mmx300 gi strip, upto switch board (from apron to switch board, the cost of gi strip with be extra) along with 30 cm square c.i. frame with hinged cover & masonry housing make as approved in u.p. p.w.d. & c.p.r.i certified si no 725 (b) item no 13 supply and laying of 25mmx3mm f.i. strips from earth directly in the ground up to control pannel as required complete in all respect (m.r.) item no 14 supply & fixing of plain or pin type copper tin plated cable socket (lug), 16 sq mm to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the engineer incharge si no 504(d) item no 15 to install tricolor rope step lights on poles (22 poles at 18 meters per pole) for lighting on iti divider roads of the city area. ...

Public Works Department - Uttar Pradesh

33214705 bids are invited for item no1 , item no2 , item no 3 , item no 4 total quantity : 40 1 supply and fixing of 12.5 mtr hight mast pole of approved make with rising system, hot dip galvanized inside & outside, having pole sheet thickness 3mm.top dia minimum 150mm, bottom dia mimium 310 mm base plate 25 mm thick suitable for wind velocity as per is 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 6 luminaries & its control gear boxes, 0.75 hp power tool motor, required internal wiring, 3 point suspension system with steel wire rope 6mm dia, double drum winch including making suitable foundation as per manufacture drawing & site requirment along with foundation bolts, nuts, washers, anchor plates etc. complete in all respect as per direction and satisfaction to the engineer in charge 2 supply and fixing of factory wired integral led flood light luminaires with die cast aluminium housing built with direver set suitable for 170 to 200 watt. confirming to ip 66 protection complete in all respect complete in all respect cat aaa 3 supply and fixing of 40 amp mcb automatic out door cubicle type control pannel for eye mast with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors, isolating switch, metering instrument and instrument box with cts etc. complete in all respect. 4 supply and burring of safe earthing electrode t 19 (hot dip galvanized), length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal dia 12mm, outer gi pipe of 16 swg and inner gi pipe of 12 swg with hot dip galvanization up to 100 micron filled with crystalline conductive mixture (ccm) having anti corrosive & conductive property with 50kgs activated soil (bfc) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square c.i. frame with hinged cover & masonry husing (from electrode terminal to switch board, cost of 25 x 3 g.i. strip will be extra) make: as approved in u.p.p.w.d., & c.p.r.i. certified....

Ministry Of Power - Uttar Pradesh

33178264 bids are invited for procurement of different type electrical items 10 phenolic laminated bakelite hylum 10x12inch 20 phenolic laminated bakelite hylum 11x13inch 30 phenolic laminated bakelite hylum 8x10inch 40 phenolic laminated bakelite hylum 9x11inch 50 phenolic laminated bakelite hylum 8x5inch 3 60 phenolic laminated bakelite hylum 5x5inchx3 70 phenolic laminated bakelite hylum 4x4inch 3 80 phnolc lamnat baklt hylm 3inchdia 3mm thick 90 pvc casing caping 12 x 10 mm 100 pvc casing caping 25x12.5 mm 110 pvc junction box 4x4inch 120 bulkhead weatherproof fixture1oow 240v 130 daily analog time switch 240vac 140 150 mm2 al. inline connector. 150 70mm2.al.in line connector als 1 160 50 mm2 al in line connector als 12. 170 al inline connector 50 sqmm als12 dowell 190 4.0 mm2 al in line connector als 5. 200 alm.tubular in line connector 210 lug al 240sqmm h / d tube trmnl 220 cable lug inchalinchtube terminal 240sqmm 230 al lugs 150sqmmal tube terminalals232 240 al lugs 185sqmmal tube terminalals235 250 al lugs 120sqmmal tube terminalals 230 260 al lugs 95sqmmal tube terminalals227 270 70mm2.al.tube terminal lug als 226 280 50mm2.al.tube terminal lug als 224 290 35mm2.al.tube terminal lug als 222 300 25mm2.al.tube terminal lug als 218 310 al lugs 16sqmmal tube terminalals 216 320 lug cu 10sqmm l / d tub trmnl dowl cus08 330 lug cu 16sqmm ring trmnl dia 8.2mm 340 lug cu 25sqmm l / d tub trmnl dowl cus10 350 lug cu 35sqmm l / d tub trmnl dowl cus12 360 change over panel total quantity : 30423...

North Eastern Railways - Uttar Pradesh

33046047 supply of digital time switch 110 240 vacdigital time switch 110 240 vac,digital time switch 110 240 vac crono 25 on/off programs, no of operating mode 5 power reserve from factory 06 years, protection ip 20 for terminals, ip 40 for enclosure similar to model no. 67dd to make l&t or similar. => limited...

Uttar Pradesh Housing And Development Board - Uttar Pradesh

32651021 electrical / mechanical work in 50 bedded eye hospital at ramai patti tehsil sadar district mirzapur electrical / mechanical work in 50 bedded eye hospital at ramai patti tehsil sadar district mirzapur 1 wiring point for light with 1.5 sq. mm.frlsh pvc insulated multistrand single core copper conductor cable in pvc conduit partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 1.5 sqmm frlsh pvc insulated multistrand copper conductor cable as earth wire drawn inside the conduit with gp box, modular type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc complete in all respect as directed including matching colour wash. pwd sor 2018 si no 138(c)+187(a) 2 wiring point for two way light with 1.5 sq. mm. frls pvc insulated multistrand single core copper conductor cable in heavy guage pvc conduit. pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting complete with 1.5 sq. mm. frlsh pvc insulated multistrand copperconductor cable as earthwire drawn inside the conduit, gp box and 2no. two way modular type switches and ceiling rose /angle /batten holder on 3 mm. thick phenolic laminated backlite sheet etc. complete in all respects, as directed including matching colour wash.pwd sor 2018 si no 139(c) + 187(b) 3 wiring point for fan / fresh air fan (light duty exhaust fan) with 1.5 sq.mm.frlsh pvc insulated multistrand single core copper conductor cable in pvc conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 1.5 sq.mm.frlsh pvc insulated multistrand copper conductor cable as earth wiredrawn inside the conduit withmodular type switch & ceiling rose on 3 mm. thick backelite sheet etc., complete in all respect including matching colour wash. pwd sor 2018 sl no 140(c )+ 187(a) 4 wiring point for call bell with 1.5 sq. mm. frls pvc insulated multistrand single core copper conductor cable in heavy guage pvc conduit. pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting complete with 1.5 frlsh pvc insulated multistrand copperconductor cable as earthwire drawn inside the conduit, gp box and modular type bell push or 2 pin shocket etc complete in all respects, as directed including matching colour wash. pwd sor 2018 si no 142(c) + 187(e) 5 wiring point for plug with 1.5 sq. mm.frlsh pvc insulated multistrand copper onductor cable in pvc conduitpartly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 1.5 sq.mm.frlsh pvc insulated multistrand copper conductor cable as earth wiredrawn inside the conduit and modular type switch and socket etc., complete in all respect including matching colour wash.pwd sor 2018 sl no 141(c )+ 187(a) 6 supply and wiring of submain with two number 2.5 sq.mm. frlsh pvc insulated 1100 v grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2mm thick) pvc conduit partly laid in slab alongwith the reinforcement before concreting and partly concealed in wall with 1 nos. 1.5 sq. mm. frlsh pvc insulated 1100 v grade multistrand single core copper conductor cable as earth continuity wire drawn inside the conduit complete in all respect. including matching colour wash. pwd sor 2018 sl no 1307(c ) 7 supply and wiring of submain with two number 4 sq.mm. frlsh pvc insulated 1100 v grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2 mm thick) pvc conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting with one no. 2.5 sq. mm. frlsh pvc insulated multistrand copper conductor cable as earth continuity wire drawn in conduit including matching colour wash etc. complete in all respect. pwd sor 2018 sl no 221(c ) 8 supply and wiring of sub main with two number 6.0 sq.mm frlsh pvc insulated 1100 v grade multstrand single core copper conductor cable in 20 mm dia heavy duty(2mm thick) pvc conduit partly concealed in wall and partly laid in slab along with reinforcement before concretiing with 1 no. 4.0 sq.mm. frlsh pvc insulated multstrand copper conductor cable as earth continuity wire drawn iin conduit including matching colour wash. complete in all respect pwd sor 2018 si no 222(c) 9 supply and wiring of 4 number 6 sq. mm. frlsh pvc insulated 1100 v grade multistrand single core copper conductor cable in 32 mm dia heavy duty (2mm thick) pvc conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting with 2 nos 4 sq.mm. frlsh pvc insulated copper conductor cable as earth continuity wire drawn in conduitincluding matching colour wash etc. complete in all respect..pwd sor 2018 sl no 277(c ) 10 supply and wiring of 4 number 10 sq. mm. frlsh pvc insulated 1100 v grade multistrand single core copper conductor cable in 32 mm dia heavy duty (2mm thick) pvc conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting with 2 nos 6 sq.mm. frlsh pvc insulated copper conductor cable as earth continuity wire drawn in conduitincluding matching colour wash etc. complete in all respect..pwd sor 2018 sl no 278(c ) 11 supply and wiring of sub main with 4 number 16.0 sq.mm frlshpvc insulated 1100 v grade multstrand single core copper conductor cable in 40mm dia pvc conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting with two number 10 sq.mm. rlsh pvc insulated copper conductor cable as earth continuity wire drawn in conduitincluding matching colour wash etc. complete in all respect. pwd sor 2018 si no 279 (c) 12 supply and fixing hexagonal/round g.p. fan box of approved make made up of 1.0 mm thick isi marked g.p. sheet spot welded four to eight holes of 25.4 mm for pipe entry of the box. holes should be semi shuttered type with 0.5 mm g.p. sheet made upper & lower cover duly screwed fitted with 300 mm round zink coated m.s bar x 12 mm & brand name should be embossed. fixing with wiring conduit laid in the r.c.c. roof before concreting along with supply of all material, labor, t&p etc. required for proper completion of the work .pwd sor 2018 s.i.no. 1149 13 supply and fixing of led tube light with metal heavy duty box type batten light fitting 1 x 22 watt suitable for upto 1x22 watt led polycarbonate tube light complete including tube suitabe for both surface & suspended complete in all respect. 2420 system lumens, 110lm/watt pf>0.95, thd<10% cri>80, sheet thicknes 0.8mm, tube with aluminium heat with 5 year warrantee. pwd sor 2018 sl no 1413 cat aaa 14 supply and fixing of led tube light with metal heavy duty box type batten light fitting 2x 22 watt suitable for upto 2x22 watt led polycarbonate tube light complete including tube suitabe for both surface & suspended complete in all respect. 2420 system lumens, 110lm/watt pf>0.95, thd<10% cri>80, sheet thicknes 0.8mm, tube with aluminium heat with 5 year warrantee. pwd sor 2018 sl no 1414 cat aaa 15 supply and fixing of recess/surface mounting round 24 watt to 32 watt cut out min 150 mm height min 40 mm, led down lighter having powder coated die cast aluminium housing with heat sink diffuser/reflector and driver set suitable for 24 hr continuous operation, compelete in all respect. pwd sor 2640 3520 system lumens, 110lm/watt pf>0.95, thd<10% at full load, cri>80, with 5 year warrantee. si no. 1405 cat aaa 16 supply and fixing of water tight oblong 10 watt led bulkhead luminaire with driver set confirming to ip 65 and above protection . complete in all respect. si no. 1417 cat aaa 17 supply and fixing of 36 watt to 46 watt indoor recess mounting led square fitting for armstrong ceiling having powder coated die cast aluminium housing body with extended heat sink and diffuser of special polycarbonate meterial and driver set complete in all respect.pwd sor 2018 s.i.no. 1406 cat a 18 supply and erection of 300 mm sweep ac 230/250 volts, 50 hz exhast fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required connection etc. complete as required mr 19 supply and erection of 400 mm sweep ac 230/250 volts, 50 hz wall fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required connection etc. complete as requiredmr 20 supply and fixing of electronic fan regulator (modular) 120 280 v. isi marked, on the existing switch board including making connections, required material, labour t&p etc. for proper completion of work to the satisfaction of engineer in charge of work. pwd sor 2018 s.i.no. 1203 (c ) 21 supply and erection of ceiling fan with motor of ac permanent insulation, capacitor rating conforming bee 5 star rating and is:374/79 and also comply with is: 1709/ 1984 with latest amendment. the rated voltage 220/240 volts, 50hz 1 ph ac the fan assemble should consists of down rod, blades, shackle, canopies etc and with double ball bearing system .pwd sor 2018 si no 1501+ 1115 bee 5 star rated 1200 mm sweep 22 s/f of 3mm thick bakelite sheet cover round/hexagonal type for fan box complete with all material, labour t&p as per direction of e/i. 23 s/f of 3mm thickal. sheet junction box cover complete in all material labour t&p as per direction of e/i. 24 supply and fixing of surface/ flush mounting 8 way tpn distribution board with additional metal door without mcb complete in all respect and directed at site by e/i. pwd sor 2018 si no 1027(a)cat a 25 s&f of 6 amp to 32 amp. spmcb (10 ka) c curve pwd sor 2018 si no 1002 cat a 26 s&f of 63 amp. 4 pole mcb (10 ka) c curve pwd sor 2018 si no 1020 (a) 27 supply and fixing of power plug with 20 amp./250 voltflush type modular switch and 5 pin 20 a/250 volt flush type universal modular socketswitch on concealed m.s boxincluding supply of all material, labour t&p etc. required for proper completion of work. pwd sor 2018 si no 1139(a) 28 s & f sheet steel enclosure surface / flush mounting fitted with 30amp. 2pin and earth metal clad scraping earth plug and socket complete in all respect. as directed at site byengineer in charge.1031 (a) 29 s & f surface/flush mounting 4ways v tpn distribution board with additional metal door without mcb complete in all respect,as directed at site by engineer in charge.pwd sor 2018 si no 1026 (c ) 30 s&f of 80 to 100 amp 4 pole mccb (16 ka) thermal magnetic releasepwd sor 2018 si no 1021 31 supply and burring of safe earthing electrode t 39 zn zinc coated, length 3000mm, outer pipe 76.3mm x 3.2 inner pipe 42.4mm x 2.6mm, terminal dia 12mm, coating 80 100 micron filled with crystalline conductive mixture (ccm) having anti corrosive & conductive property with 50 kgs activated soil (bfc) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square c.i. frame with hinged cover & masonry housing. (from electrode terminal to switch board, cost of 25 x 3 g.i. strip will be extra make: as approved in u.p. p.w.d., & c.p.r.i. certified pwd sor 2018 si no 726 (d) 32 supply and laying of 25 mm x 3 mm g.i srtip form earth electrode directly in the ground as required complete in all respects. pwd sor 2018 si no 716 33 supply and laying of 32 mm x 6 mm g.i. strip from earth electrode directly in the ground as required complete in all respect. pwd sor 2018 si no 717 34 providing, laying and fixing 80 mm dia g.i. pipe (medium class) in ground complete with g.i. fittings including trenching (75 cm deep)and re filling etc as required. dsr 2018 si no 18.12.8 35 supplyandlayingof aluminiumconductorpvcinsulated armoured served sheathed cables 1100 volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. on surface the cable run shall be fixed on m.s. clamps etc. of suitable size or as directed by the engineer incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. pwd sor 2018 si no 501 36 10 sqmm 4 core 37 16 sq mm 4 core 38 70 sq mm 3.5 core 39 95 sq mm 3.5 core 40 240 sq mm 3.5 core 41 supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. the armouring ofthe cable shall be properly connected with the earth as per direction of engineer incharge.pwd sor 2018 si no 503 42 10 sqmm 4 core 43 16 sq mm 4 core 44 70 sq mm 3.5 core 45 95 sq mm 3.5 core 46 240 sq mm 3.5 core 47 supply and fixing of plain or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connection etc. complete in all respects as per direction of the engineer incharge.pwd sor 2018 si no 504 48 10 sqmm 49 16 sq mm 50 35 sq mm 51 50 sq mm 52 70 sq mm 53 95 sq mm 54 120 sq mm 55 240 sq mm 56 supply and fixing of call bell of approved make on polished mdfeg / teak ply board including making connections etc. complete in all respect. pwd sor 2018 si no 1101 57 supply of franklin france make advanced piezoelectric exciter device based lighting protection system suitable for protection of building against direct lightning strike complete with ealy streamer emission with piwezoelectric device for corona effect) stainlles steel lighting conductor air terminal with event counter with sensitivity 1 ka to 100 ka for 8.20 micro second impulse for 1 ka control over the release of ions positive or negative without additional power supplies requirement required complianece with ip53 enclosures) 58 saint elmo lightening conductor with discharge counter (sensitivity 1 ka, 8/20 microsecound with ip 53 enclosures) 59 elevation rod : 2m. afc2001 two elevation rods for are required for mounting a one lightening conductor mr 60 installation of franklin france make external lightening protection system. 61 supply and fixing of vertical down conductor of 32mm x 6mm g.i. strip etc. on approved clamps on surface for lightning conductor complete in all respects (for two storeyed buildings).p.w.d.s.o.r. 2018 s.i. no.713( c) 62 supply and fixing of testing joint of g.i. strip 32mm x 6mm and 150mm long with g.i. bolts and nut etc. complete in all respect.p.w.d.s.o.r. 2018 s.i. no.719 63 supplying and fixing following modular switch/ socket on theexisting modular plate & switch box including connections but excluding modular plate etc as required. (i)telephone socket outlet dsr no 1.24.6 64 supply and fixing of g.p. modular switch box for 1 / 2 module of approved make made up of 1.0 mm thick isi marked g.p.sheet including adjestable nakka and holes plugged with pvc nylon caps . two or more holes for pipe entry of 25.4 mm on upper and lower sides of the box. holes should be semi shuttered type and fitted with heavy brass earth piller duly screwed & brand name should be embossed. box flushed in wall including cutting of brick work, fixing it to the level with cement sand mortar, including matching colour wash with s/o all materials, labour and t&p required for proper completion of work as directed at site by the engineer in charge. p.w.d.s.o.r. 2018 s.i. no.1152(a)(i) 1 or 2 module (75mm x 75 mm) 65 supplying and drawing telephone wire following pair 0.5 sqmm fr pvc insulated annealed copper conductor, unarmoured telephone cable in the existing surface/recessed steel/pvc conduit as required. dsr no 1.18.22 pair 66 supply and fixing and concealing of 20 mm dia. 2mm thick pvc conduit pipe with isi mark embossed and with pvc accessories confirming to is no. 3419 for drawing wires duly sealed at joints with original resin / adhesive to make the complete piping rigid, plastering with cement sand mortar finished to the level with matching colour wash including cost of all material labour and t&p etc required for proper completion of the work as per directions and to the satisfaction of engineer in charge. sor 2018 si no. 148(a) 67 supply and laying of 1800mm x 900mm x 12mm thick chequered rubber matting of tested quality sor 2018 si no. 1136 68 fire fighting systemproviding, laying, testing & commissioning of c class heavy duty ms pipe conforming to is 3589/is 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : dsr & aor 2019 si no 7 69 150 mm dia 70 100 mm dia 71 80 mm dia 72 65mm dia 73 32mm dia 74 25 mm dia 75 providing laying, testing & commissioning of c class heavy duty ms pipe conforming to is 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per is 10221, refilling the trench etc. of following sizes complete as required. dsr & aor 2019 76 150 mm dia si no 6.2 77 supplying,fixing, testing and commissioning of manual swing typehose reel is:444 complete with heavy duty reel, 20 mm dia. x 30 mtr long, pvc pressure hose pipe , red coloured, ss jet nozzel, 25mm. isolating valve and all other neccessary fixing accesories complete in all respect. dsr no 17:1 78 supplying and fixing single headed internal hydrant valve with instantaneous gunmetal/stainless steel coupling of 63 mm dia with cast iron wheel isi marked conforming to is 5290 (type a) with blank gunmetal/stainless steel cap and chain as required :as per dsr & aor 2019 s.i. no. 9.1 79 supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to is 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : dsr & aor 2019si no. 18.1 80 supplying and fixing 63 mm dia, 15 m long rrl hose pipe with 63 mm dia male and female couplings duly bound with gi wire, rivets etc. conforming to is 636 (type a) as required : dsr & aor 2019 si.no.16.1 81 providing and fixinghose box (600x300x200)size of suitable size made out of 16/18 swg thick having central opening and 4 mm thick glazed glass double door including necessory rubber beading key pocket, handle locking arrengment painting with polyurethene based red paint etc. the words fire hose to be painted on the dooor as per approved drawing complete in all respect. mr 82 supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia ms pipe connection conforming to is 904 as required : 83 2 way 100 mm dia m.s. pipe si no. 19.1 84 supply, fixing, testing and commissioning of 25mm ball valve complete. mr 85 supplying and fixing air vessel made of 250 mm dia, 8 mm thick ms sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. dsr & aor 2019 si no. 20 86 supplying, installation, testing and commissioning of electric driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required: (main fire pump)(a) horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to is : 1520(b) suitable hp squirell cage induction motor tefc type suitable for operation on 415 volts, 3 phase, 50 hz, ac supply with ip55 class of protection for enclosure, horiziontal foot mounted type with class f insulation, conforming to is 325.(c) m.s.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.(d) suitable cement concrete foundation duly plastered and with anti vibration pads.supplying and fixing air vessel made of 250 mm dia, 8 mm thick ms sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.1620 lpm at 70 m head dsr & aor2019 si no. 1.8 87 supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (diesel driven pump)horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to is 1520. suitable hp, 1500 rpm water cooled with radiator, diesel engine conforming to relevant is standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. m.s fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. suitable cement concrete foundation duly plastered and with anti vibration pads.make : kirloskar/ other standard make.dsr no. 2.81620 lpm at 70 m head 88 supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (jockey pump) a) horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to is : 1520.b) suitable hp squirell cage induction motor tefc type suitable for operation on 415 volts, 3phase 50 hz ac supply with ip 55 class of protection for enclosure, horizontal foot mounted type with class f insulation, conforming to is : 325.c) m.s.fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. suitable cement concrete foundation duly plastered and with anti vibration pads. make kirloskar/other standard make dsr no. 3.2180 lpm at 70 m head 89 supplying, installation, testing and commissioning of electric driven terrace pump suitable forutomatic operation and consisting of following, complete in all respects, as required: (terrace pump)(a) horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to is : 1520 b) suitable hp squirell cage induction motor tefc type suitable for operation on 415 volts, 3 phase, 50 hz, ac supply with ip55 class of protection for enclosure, horiziontal foot mounted type with class f insulation, conforming to is 325. (c) m.s.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) suitable cement concrete foundation duly plastered and with anti vibration pads.450 lpm at 35 m head 90 automatic control panel(s) fabrication, supply, insallation testing & commissioning of electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick crca sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, inter connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per cpwd specification with following in coming and outgoings, suitable for operation on 415v, 3 phase, 50hz ac supply with enclosure protection class ip 42 as required : incoming 250a, 50ka 4 pole mccb, ics=100% icu rating digital voltmeter 0 500v with selector switchdigital ammeter (0 250 a) with selector swtich & cts etc.outgoing main fire pump : 125 a 50ka tpn mccbjockey pump : 63 a , 50ka tpn mccb, diesel engin control complete in all respect dsr no. 5.1 91 providing & fixing of pressure switch in m.s. pipe line including connection etc. as required. dsr & aor 2019 si no. 22 92 providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required dsr 2018 si no. 16.8 93 sitc of foot valves with strainer at the suction pipe of fire pumps (in case of negative suction only). make kalpana/kartarsir/advance or equivalent 94 150mm dia 95 100mm dia 96 supplying, fixing, testing and commissioning of butterfly valve of pn 1.6 rating with bronze/gunmetal seat duly isi marked complete with nuts, bolts, washers, gaskets conforming to is 13095 of following sizes as required : dsr & aor 2019 si no 11 97 150 mm dia 98 100 mm dia 99 80 mm dia 100 providing, installation, testing and commissioning of non return valve of following sizes confirming to is: 5312 complete with rubber gasket, gi bolts, nuts, washers etc.as required : dsr & aor2019 si no. 14 101 150 mm dia 102 100 mm dia 103 supply and fixingof c02 type fire extinguisher 4.5 kg. capacity (isi marked is : 2878 & tac approved) complete with initial charge and wall bracket, along with supply of all materials and labourfor proper completionof work.pwd sor 2018 si no 1132 104 supply and fixingof fire extinguisher,abc type 6.00 kg. capacity(isi marked is : 15683 & tac approved) complete with initial charge and wall bracket, along with supply of all materials and labourfor proper completionof work.pwd sor 2018 si no 1131(a) 105 supply and fixing of self glow type exit sinage. 106 sitc ofsprinkler 68° deg, complete in all respects. (make: omex/ life guard/safex) dsr 2019 si no. 21.1pendent type 107 fire alarm system worksupplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card,minimum 320 character graphics/ lcd display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (eprom), power supply unit (230± 5% v, 50 hz), 48 hrs back up with 24 volt sealed maintenance free batteries with automatic charger. the panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under sh: pa system) and shall be complete with all accessories . the panel shall be compatible for ibms system with open protocol bacnet/ modbus over ip complete as per specifications. dsr 2018 si no 17.2.1.1two loop panel. 108 supplying, installation, testing & commissioning of intelligent analog addressable photo thermal detector complete with mounting base complete as required. dsr 2018 si no 17.2.4 109 supplying, installation, testing & commissioning of response indicator on surface/recessed ms box having two led, metallic cover complete with all connections etc as required.dsr 2018 si no 17.2.5 110 supplying, installation, testing & commissioning of addressable phone control module complete as required. dsr 2018 si no 17.2.11 makeinnel/simplex/tyco 111 supplying, installation, testing & commissioning of addressable manual call point complete as required. dsr 2018 si no 17.2.14 112 supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. dsr 2018 si no 17.2.15 113 supplying, installation, testing & commissioning of addressable fire control module complete as required. dsr 2018 si no 17.2.10 114 supplying, installation, testing & commissioning of faultisolator complete with base as required. dsr 2018 si no 17.2.7 115 supplying, installation, testing & commissioning of repeater panel wih 320 character/ touch screen lcd display with inbuilt reset ackowledge and silence switches complete as required.dsr 2018 si no 17.2.3 116 supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000v rated with annealed copper conductor having xlpe insulation, steel wire armouring & frls outer sheath complete as required.. dsr 2018 si no. 17.5.2 117 supplying, installation, testing & commissioning of 6 zone,voice alarm controller with usb, mp3 player (including 6 zonebutton paging station) with seamless integration facility withmain fire alarm panel for voice evacuation complete asrequired dsr 2018 si.no.17.3.1 118 supplying, installation, testing & commissioning of 1.5/3/6w metal box ceiling/wall speakers complete as required.dsr 2018 si.no.17.3.3 119 supplying, installation, testing & commissioning of digital audio amplifier 50 watt, 25v rms operating at 240 volt ac supply complete as required.dsr 2018 si.no.17.3.6 120 supplying, installation, testing & commissioning of voice command keypad 6 zone, with microphone assembly complete as required.dsr 2018 si.no.17.3.9 121 tubewell workboring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in is: 2800 (part i), including collecting samples from different strata, preparing and submitting strata chart! bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90 metre depth below ground level. dsr 2019 sino. 23.1.1 122 350 mm dia upto 60 msino. 23.1.1.2 123 60 90 msi no. 23.1.1.1 124 90 150 msi no. 23.2.1.1 125 supplying, assembling, lowering and fixing in vertical position in bore well, erw (electric resistance welded) fe 410 mild steel screwed and socketed/plain ended casing pipes of required dia, conforming to is: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of engineer in charge. dsr 2019 si no. 23.10 126 150 mm nominal size dia having minimum wall thickness 5.00 mm si no. 23.10.2 127 200 mm nominal size dia having minimum wall thickness 5.40 mm si no. 23.10.3 128 supplying, assembling, lowering and fixing in vertical position in bore well, erw (electric resistance welded) fe 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed / plain bevel ended pipe (type a) of required dia, conforming to is: 8110, of reputed and approved make, having wall thickness not less than 5.40 mru, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fitting & accessories, all complete, for all depths, as per direction of engineer in charge. dsr 2019 si no. 23.11 150 mm nominal size dia si no. 23.11.2 129 providing and fixing bail plug/ bottom plug of required dia to the bottom of pipe assemblv of tube well as oer is:2800 (dart n.dsr 2019 si no. 23.15 150 mm dia si no. 23.15.2 130 providing and fixing m.s. clamp of required dia to the top of casing! housing pipe of tube well as per is: 2800 (part i), including necessary bolts & nuts of required size complete. dsr 2019 si no. 23.14(i) 200 mm clamp si no. 23.14.3 131 supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of engineer in charge. dsr 2019 si no. 23.6 132 development of tube well in accordance with is : 2800 (part 1) and is: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by v notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, ilc disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of engineer in charge dsr 2019 si no. 23.12 133 providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing! casing pipe, rmovable as per requirement, all complete for borewell of: dsr 2019 si no. 23.13 200 mm dia si no. 23.13.3 134 500 lpm 52 m head of k s b make submersible pumping plant sitc submersible pump set suitable for clear and cold water with bronze impellers and built in non return valve and suitable to run on 400 volts, 3 phase 50 hz a.c. supply at 2900 rpm (nominal) speed and complete with 3 mts. submersible cable. 135 sitc of sheet steel fabricated cubical type wall mounting type panel with front opening door. the panel will be complete with internal wiring and will have 3 nos. instruments fuses and 3 nos. toggle switches. 136 main piping and valves (01 no ci df reflux valve, 02 no ci df sluice valve, 01 no ci df bend, 01 no enlarger of necessary size, if required, 01 no ci af tee, 01 no ci df pipe 1.0 mt long, 02 nos ms df pipe 1.5 mt long, 30 mts ms column pipe flanged type in lenghts of 3.0 mts each, 02 pairs column pipe clamps) 137 pressure & depth gauge (01 no 100 mm dial size pressure gauge feibiq make, 01 no 100 mm dial size depth gauge feibiq make, 01 no control cock for pressure gauge, 35 mts. steel air line with sockets, 01 sets union joints, schraeder valve, hand air pump and gauge board etc.) 138 lifting tackle indef make spur geared lifting tackle of capacity 02 tonnes tested to 03 tonnes with load and hand chain for 4.5 mts lift. 139 special tools and spanners (01 no wooden tool board with l hooks, 01 no hammer with handle, 01 set de spanners consisting of 06 pcs, 02 nos screwdrivers, 01 no 350 mm size pipe wrench, 01 no combination plier) 140 installation of one complete pump set with switchgear material, main piping and valves and do the power wiring work. 141 commissioning of one pumping plant as and when the department arranges the power connection at the site. 142 painting of the switchgear material and delivery pipes and special inside the pump house with 02 coats of enamel paints. 143 testing of the pump at site and the test will be subject to tolerences as provided in the relevant iss. 144 chlorinatorsupply of aquas make electronic chlorinator of 6lph capacity complete accessories and 100 ltr, pvc solution tank. 145 installation charges (1/2 socket fixed in pipe line to provide by the department, 146 street lightsupply and fixing of 7.0 meter long g.i. octogonal pole top dia 70 mm bottom dia 130 mm andbase plate 12 mm thick having3 mm thickness with single arm braclet (1 meter length ) on rcc foundatoion including the cost of foundation ,foundation bolts, excavation & baack filling and required t&p complete fn all respect pwd sor 2018 s.i. no 641 147 supply and fixing of led street light fitting having dia cast aluminium body and diffuser with driverset suitable for 75 to 90 watt. confirming to ip 65 and above protection complete in all respect. pwd sor 2018s.i.no. 1423 cat aaa 148 providing, laying and fixing following dia g.i. pipe (medium class) in ground complete with g.i. fittings including trenching (75 cm deep)and re filling etc as required80 mm dia sor aligarh 2020 149 supply and fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors , hrc fuses, isolatingswitch metering intrument & instrument box with cts etc. in case of tpn, comp;ete in all respect pwd sor 2018 s.i.no. 807 40 a tpn 150 supply and laying of 25mm x 3mm g.i. strip from earth electrode directly in the ground as required complete in all respect. pwd sor 2018 s.i.no. 716 151 supply and burring of safe earthing electrode t 19 (hot dip galvanized), length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal dia 12 mm, outer gi pipe of 16 swg and inner gi pipe of 12 swg with hot dip galvanization up to 100 micron filled with crystalline conductive mixture (ccm) having anti corrosive & conductive property with 50 kgs activated soil (bfc) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square c.i. frame with hinged cover & masonry husing (from electrode terminal to switch board, cost of 25 x 3 g.i . strip will be extra) make: as approved in u.p. p.w.d., & c.p.r.i. certified. pwd sor 2018 s.i.no. 725 (a) 152 solar water heaterspecial system featuresevacuated tube collectorno. pressurized tankgi tank with special passivation coating & magnesium anode to prevent corrosioninner tank with 100 mm puf insulation including cost of gi frame structure, earthing and other required civil work complete all respect as per direction of e/i. 153 solar power system including cost of gi frame structure, earthing and other required civil work complete all respect as per direction of e/i. 154 main lt panel: design, manufacturing, supply installation, testing & commissioning of lt switchgear panels suitable for 433 v, 3 phase, 4 wire, 50 hz power distribution system. the panel shall be indoor, free standing, floor mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type compartmentalised design fabricated out of 14 swg crca sheet steel, complete with colour coded, heat shrinkable pvc insulated, aluminium bus bars and separate earth bus bar of adequate cross section through out the length of the panel. the incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable alley, bus bar alley/chamber. the panel shall be complete with name plate, earthing, numbering, danger plate etc. as required and as per specifications and drawings. the panel shall withstand the fault level of 25ka as per single line diagram.a) 1 no. incoming 320a fp 35ka mccb with with o/c, s/c& e/f release, , spreaders & extended roary handle along ct, metering, compelete with all fuses wiring etc and. for 160kva css incomer.b) 1 nos. outgoing 160a 25ka tp mccb with extended rhom along with o/c & s/c protection, along with ammeter with ammeter selector switch, ct etc.c) 1 nos. outgoing 125a 25ka tp mccb with extended rhom along with o/c & s/c protection, along with ammeter with ammeter selector switch, ct etc. c) 8 nos. outgoing 63a 25ka tp mccb with extended rhom along with o/c & s/c protection, along with ammeter with ammeter selector switch, ct etc. 155 emergency cum amf paneldesign, manufacturing, supply installation, testing & commissioning of emergency cum amf panels suitable for 433 v, 3 phase, 4 wire, 50 hz power distribution system. the panel shall be indoor, free standing, floor mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type compartmentalised design fabricated out of 14 swg crca sheet steel, complete with colour coded, heat shrinkable pvc insulated, aluminium bus bars and separate earth bus bar of adequate cross section through out the length of the panel. the incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable alley, bus bar alley/chamber. the panel shall be complete with name plate, earthing, numbering, danger plate etc. as required and as per specifications and drawings. the panel shall withstand the fault level of 25ka as per single line diagram. 156 a) 1 no. mains supplyincoming 125a tp 25ka mccb with o/c & s/c release, ct, metering, compelete with all fuses wiring etc.b) 1 no. dg supplyincoming 125a tp 25ka mccb with o/c & s/c release, ct, metering, compelete with all fuses wiring etc. logic control wiring with required relays, timers etc. with trickle/boost battery charger with dc ammeter & voltmeter etc. compelete with all fuses wiring etc and.c) 2 nos. outgoing 100a 25ka tp mccb with extended rhom along with o/c & s/c protection, along with ammeter with ammeter selector switch, ct etc. d) 6 nos. outgoing 63a 25ka tp mccb with extended rhom along with o/c & s/c protection, along with ammeter with ammeter selector switch, ct etc. e) 4 no. outgoing 40a 25ka tp mccb with extended rhom along with o/c & s/c protection, along with ammeter with ammeter selector switch, ct etc. 157 apfc paneldesign, manufacturing, supply installation, testing & commissioning of lt apfc panel as under suitable with incomer bus bar for 433 v, 3 phase, 4 wire, 50 hz power distribution system. the panel shall be indoor, free standing, floor mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type compartmentalised design fabricated out of 14 swg crca sheet steel, complete coded, heat shrinkable pvc insulated, aluminium bus bars and separate earth bus bar of adequate cross section through out the length of the panel. the incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable alley, bus bar alley/chamber. the panel shall be complete with name plate, earthing, numbering, danger plate etc. as required and as per specifications and drawings. the panel shall withstand the fault level of 25ka. the panel shall be completed in all respect as per below mentioned boq and.a) 100kvar 10 stage with 160a tp, 25ka mccb incomer with metering &individal mcb/mccb for feeder protection alongwith microprocessor based apfc relay 158 normal floor vertical tpn db (double door)supply installation, testing & commissioning of normal vtpn db suitable for 433 v, 3 phase, 4 wire, 50 hz. the db shall be indoor double door type, sheet metal clad, cubicle, dead front, dust and vermin proof fabricated out of crca sheet steel, complete with colour coded, bus bars and separate earth connection of adequate capacity. the incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable box/ alley. the db shall be complete with name plate, earthing, numbering, danger plate etc. as required and as per specifications and drawings. the panel/ db shall withstand the fault level of 10ka as per single line diagram. 159 stilt floor vertical tpn db 4 way (double door) normal supply sor 2018 si no. 1026(c ) +1021+1016a) 1no. incoming 63a (16ka) fp mccbb) 4 nos. outgoing 40a tp mcb (10ka) 160 first &fourth floor vertical tpn db 6 way (double door) normal supply a) 1no. incoming 63a (16ka) fp mccbb) 5 nos. outgoing 40a tp mcb (10ka) si no. 1027 (c )+102+1016 161 second floor vertical tpn db 8 way (double door) normal supplya) 1no. incoming 63a (16ka) fp mccbb) 5 nos. outgoing 40a tp mcb (10ka) si no.1028 © +121+1016+101c) 3 nos. outgoing 32a tp mcb (10ka) 162 third floor vertical tpn db 6 way (double door) normal supplya) 1no. incoming 63a (16ka) fp mccbb) 1 no. outgoing 50a tp mcb (10ka) c) 5 nos. outgoing 40a tp mcb (10ka)si no. 1027 (c )+1021+1017+1016 163 emergency floor vertical tpn db (double door)supply installation, testing & commissioning of emergency vtpn db suitable for 433 v, 3 phase, 4 wire, 50 hz. the db shall be indoor double door type, sheet metal clad, cubicle, dead front, dust and vermin proof fabricated out of crca sheet steel, complete with colour coded, bus bars and separate earth connection of adequate capacity. the incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable box/ alley. the db shall be complete with name plate, earthing, numbering, danger plate etc. as required and as per specifications and drawings. the panel/ db shall withstand the fault level of 10ka as per single line diagram. 164 stilt, floor vertical tpn db 4 way (double door) emergency supplya) 1no. incoming 40a (16ka) fp mccbb) 4 nos. outgoing 32a tp mcb (10ka)si no. 1026 (c )+1021+1013 165 first, second, thirdfloor vertical tpn db 8 way (double door) emergency supplya) 1no. incoming 63a (16ka) fp mccbb) 2 nos. outgoing 40a tp mcb (10ka) c) 4 nos. outgoing 32a fp mcb (10ka)si no. 1028 (c )+1021+1016+1013 166 fourth floor vertical tpn db 6 way (double door) emergency supplya) 1no. incoming 40a (16ka) fp mccbb) 5 nos. outgoing 32a tp mcb (10ka)si no. 1027 (c )+1021+1013 167 11kv switch gear (incoming cum outgoing vcb panel)supply of single panel (incoming cum outgoing) set 11kv, 500mva indoor type metal clad floor mounted vermin proof horizontal drawout fully interlocked vertical/horizontal isolation vacuum circuit breaker panel board fabricated out of minimum 2mm thick crca sheet as per specifications. the panel shall be complete with all accessories / fitting / wiring like insulated copper busbar, cable termination boxes suitable for upto 3c x 300 sqmm xlpe armoured, aluminium conductor cable for incoming and outgoing feeder, foundation bolts etc. complete as required and as specified below : incoming cum outgoing : 1 set (each consisting of) 168 one (1) nos. 11kv 630 amps. 500mva, 26.3ka for 3sec. electrically/ manually operated draw out type vacuum circuit breaker complete with trip free spring charged closing mechanism, necessary auxiliary relays, control switches, emergency hand trip devices and mechanical on / off indicator etc. one (1) multifunction meter showing all electrical paramaterie volt, ampere, kw, kva, p.f., kwh etc.one (1) digital type ammeter with 11kv cast resin cts for metering (50/25 /5 5a, cl1, 15va) with ass and 2 amp sp mcb.one (1) voltmeter (0 15kv) with vss.one (1) set of phase indication lamps with 2amp sp mcb for protection (red, yellow and blue).one (1) set of red/ green indicating lamp for close and open position.one (1) no. amber indicating lamp for auto trip.one (1) no. clear indicating lamp for trip circuit healthy. one (1) blue indicating lamp for spring charged.one (1) strip heater to prevent absorption of moisture.one (1) set of 3 o/c + 1e/f (with high set) neumerical relay with 3 nos. 11kv resin cast cts 50/25/5 5a, cl 10p10, 15va.master trip relay.trip circuit supervision relayone (1) no. potential transformer 11kv/v3/110/v3 100va burdenone (1) set of 3element 24v dc aux. relay with h/r flag for tripping of transfomerfault ie. oti, wti & buchholz tripping. one (1) set of 3element 24v dc aux. relay with h/r flag for alarm of transfomerfault ie. oti, wti & buchholz alarm. one (1) set of 8 stage 24v dc annunciator with builtin test/accept/ reset push button along with 24v dc hooter. master trip relay.12 window annunciatorauxiliary switch/relay, master trip, anti pumping relay trip circuit supervision relay and other control relays etc. as per requirements.power pack :one (1) set 230v a.c, / 24v dc, 42ah battery backup, power pack to operate atlease 3nos. operation without ac supply. 169 125 kva 11kv / 0.415kv transformer:design, manufacture, supply, installation, testing and commissioning of 11kv/0.415kv, 125kva transformer with percentage impedance 5% (approx.) (without negative tolerance), 3 phase, 50 hz delta/star connected, outdoor, oil filled, onan type transformer, complete with all fittings such as marhslling box thermometers (oti), wti, buchholz relay, off load tapp changer with + 5 % to –12.5%, tapping at the step of 2.5% bi directional roller, diagrams & rating plate & winding temperature indicator, oil temperature indicator, lifting lugs, h. t. cable box/ lt cable box suitable for termination of cable. transformner shall confirm to latest is : 1180 energy efficiensy level i including making of rcc foundation of size suitable for 125kva transformer.complete in all respect. 170 supply and laying of 3 core standered aluminium conductor xlpe (cross linked polyethylene) insulated pvc bedded, galvanised flat steel strip armoured cables confirming to i.s. 7098 (part ii with latest amendments) ii kv grade at a depth of 900 mm below ground level over a cushion of 100 mm thick fine river sand all around and protected with well burnt bricks on sides and on top put across. the armouring of cable shall be properly connected with earth conductor by clamps etc. pwd sor 2018 si no. 50670 sq. mm 3 core 171 supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, xlpe aluminium conductor cable of 11 kv grade as required dsr 2018 si no. 10.4.170 sqmm 172 supply of 62.5 kva three phase silent dg set comprising of cummins make engine model 4btaa3.3 g11 developing 84 bhp and 62.5 kva, 415 v stamford make alternator mounted on a common base, complete with fuel tank, batteries and leads, residential silencer, standard panel, first fill of lube oil, avm pads, acoustic enclosure 173 amf panel suitable for 62.5 kva dg set 174 pcc foundation mixing ratio 1:2:4 cement, morang, concrete suitable size of dg set 175 gi pipe chemical earthing 50x3000mm complete with back filled compound 176 installation: like unloading & shifting at site, cable aluminium 70x3.5 c 20 meter, control wiring for amf panel, end termination of cabletesting, commissioning withdiesel. ...

Uttar Pradesh Jal Nigam - Uttar Pradesh

32480729 invitation of rates for supply of rates for civil, electrical, sanitory and other materials as per bid document , electrical, sanitory & other material , providing m.s. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 ( 1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size ) as per standard design: with 20x20mm square bar , providing and fixing in position precast rcc manhole cover and frame of required shape and approved quality. m.d. 10 circular shape 500mm internal diameter , boring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in is: 2800 ( part i ) , including collecting samples from different strata, preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, beyond 90 metre & upto 150 metre depth below ground level. drilling of 300mm dia bore hole manually. , supplying, assembling, lowering and fixing in vertical position in bore well unplasticized pvc medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction ofengineer in charge. 150 mm nominal size dia , supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of engineer incharge. , gravel packing in tubewell construction in accordance with is: 4097, including providing gravel fine / medium / coarse, in required grading & sizes as per actual requirement, all complete as per direction of engineer in charge. , providing m.s. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 ( 1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size ) as per standard design: with 20x20mm square bar , excavating trenches in all kinds ofsoil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. up to 1.50 m depth, pipes 80 mm to 300 mmdiameter , a ) inside size 60x60 cm & 90 cm deep including c.i. cover with frame ( light duty ) total wt. of cover & frame to be not less than 38 kg ( wt. of cover 23 kg & wt. of frame 15 kg. , constructing of r.c.c. surface drain complete as per standard design: , drain 300 wide average.depth 45 cm , drain 450 wide average.depth 60 cm , 0.91 m deep with s.f.r.c. grating and frame ( heavy duty, hd 20 grade designation ) 560 mm internal diameter conforming to is : 12592, total weight of cover and frameto benot less than 182 kg., fixed in cement concrete 1:2:4 ( 1cement : 2 coarse sand : 4 gradded stone aggregate of 20 mm nominal size ) including centering shuttering all complete. ( excavation, footrest and 12 mm thick cement plaster at the external surface shall be paid for separately ) , 40 mm thick rubbed stone flooring over 20 mm ( average ) thick base of cement mortar 1:5 ( 1 cement : 5 coarse sand ) with joints 3 mm thick, side buttered with cement mortar 1:2 ( 1 cement : 2 stone dust ) admixed with pigment to match the shade of stone and pointing with same mortar. red sand stone , providing and stacking of nauclea cadamba ( kadam ) of height 150 165 cm. in big poly bag of size 25 cm as per direction of the officer in charge. , providing and stacking of nyctanthes arbor tristis ( hasingar ) of ht. 90 105 cm in earthen pots of size 20 cm as per direction of the officer in charge. , providing and stacking of terminalia arjuna of height 150 165 cm. in big polybags of size 25 cm as per direction of the officer in charge. , providing and stacking of plumeria alba dwarf dwarf of height 90 105 cm. with 3 4 branches and thick stem in big size hdpe bags as per direction of the officer in charge. , providing and stacking of plumeria rubra of height 120 150 cm. with 3 4 branches and thick stem in big size hdpe bags as per direction of the officer in charge. , providing and stacking of bassia latifolia ( mahua ) of height 90 105 cm. in big polybag of size 25 cm as per direction of the officer in charge. , providing and stacking of eugenia jambolana ( jamun ) of height 150 165 cm. in big poly bags of size 25 cm as per direction of the officer in charge. , providing and stacking of psidium guajava ( amrood ) of height 150 165 cm. in big poly bags of size 25 cm as per direction of the officer in charge. , providing and stacking of phyllanthus emblica ( amla ) of height 150 165 cm. in big hdpe bag as per direction of the officer in charge. , providing and stacking of mangifera indica ( mango grafted ) of height 60 75 cm. in big poly bag of size 25 cm as per direction of the officer in charge. , providing and stacking of azadirachta indica ( neem ) of height 120 130cm in big polybag of size 25 cm as per direction of the officer in charge. , providing and stacking of ficus racemosa ( goolar ) of height 150 165 cm. in big hdpe bag as per direction of the officer in charge. , providing and stacking of ficus religiosa ( peepal ) of height 150 165 cm. in big poly bags of size 30 cm as per direction of the officer in charge. , providing and stacking of ficus virens ( paakad ) of height 150 165 cm. in big poly bags of size 30 cm as per direction of the officer in charge. , providing and stacking of ficus bengalensis ( bargad ) of height 120 135 cm. in big poly bags of size 25 cm as per direction of the officer in charge. , providing and stacking of ficus panda of height 90 105 cm. with 10 12 branches and healthy foliage, well formed in cement pots of size 30 cm as per direction of the officer in charge.. , providing and stacking of ficus reginald well branched, bushy of height 60 75 cm. in earthen pots of size 25 cm as per direction of the officer in charge.. , providing and stacking of duranta golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of earthen pot / plastic pot & as per direction of the officer in charge.. , providing and stacking of tradescantia zebrina having in 15 cm size of earthen pot / plastic pot & as per direction of the officer in charge. , providing and stacking of wedelia trilobata, full of leaves in 15 cm size of poly bags & as per direction of the officer in charge. , providing and stacking of asparagus sprengeri of height 15 cm to 20 cm, full of leafy branches in 15 cm size of earthen pot / plastic pot & as per direction of the officer in charge.. , providing and stacking of ophiopogon jaburan ( variegated ) , full of variegated leaves in earthen pot / plastic pot of size 20 cm. as per direction of the officer in charge. , providing and displaying of croton petra bangalore variety having ht. 60 cm to 75 cm with 4 to 6 branches, well developed, fresh and healthy colorful leaves in 25 cm size of earthen pot / plastic pot & as per direction of the officer in charge. , making tree guard 53 cm dia and 1.3 m high as per design from empty coal tar drums, supplied free by the department, including providing and fixing 2 nos m.s. sheet rings 50 x 0.5 mm fixed with rivets complete in all respects including painting inside and outside of tree guard with: two or more coats of synthetic enamel paint of approved quality shade over a priming coat , trenching in ordinary soil up to required depth including removal and stacking of serviceable materials and then disposing of as directed and spreading earth & neatly levelling, breaking clods etc. and making the trenched area with designed mounds, paths and sitting spaces etc. to proper levels by filling with earth or earth mixed with manure and properly watering complete work in required topography as per drawing & specifications. , supplying and stacking of good earth at site including royalty but including carriage1km ( earth measusred in stacks will be reduced by 20% for payment ) . , supplying and stacking at site dump manure from approved source, including carriage up to 1 km ( manure measured in stacks will be reduced by8% for payment ) , mixing earth and manure in specified proportion or as directed. , rough dressing the trenched ground including breaking the clods. , fine dressing the ground , spreading ofmixed good earth and manure in specified proportions as above and in required thickness. , uprooting weeds from the trenched area after 10 to 15 days after flooding with water including disposal of uprooted vegetation. , providing & laying selection no. 1 grass turf with earth 50mm to 60mm thickness on existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same, as per direction of officer in charge , preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of officer in charge. , supply , installation , testing and commissioning oftwinkle lites make 3000mm long hybrid decorative pole humberto h pole with gravity casted cast aluminium base and ripped gi pole pipewith decorative post top lantern concord 1270mm long with polycarbonate diffuser in 60w led having lumen output not less than 110lmns / watt with 10kva surge protector designed as per architect in charge ( make twinkle lite / havells / neri / juvaas / orient / thor ) , supply , installation , testing and commissioning oftwinkle lites make gate light lantern concord 1270mm long with polycarbonate diffuser in 60w led having lumen output not less than 110lmns / watt with 10kva surge protector designed as per architect in charge ( make twinkle lite / havells / neri / juvaas / orient / thor ) , supply , installation, testing and commissioning oftwinkle lites make 1000mm longdecorative bracket tlb 69 wl with decorative post top lantern concord 1270mm long with polycarbonate diffuser in 90w led having lumen output not less than 110lmns / watt with 10kva surge protector designed as per architect in charge ( make twinkle lite / havells / neri / juvaas / orient / thor ) , supply and burring of safe earthing electrode t 19, ( hot dip galvanized ) , length up to 3000mrn, outer dia 50 mm inner dia 25mm, terminal dia 12mm, outer gi pipe of 16 swg and inner gi pipe of l2 swg with hot dip galvanization up to 100 micron filled with crystalline conductive mixture ( ccm ) having anti corrosive & conductive property with 50 kgs activated soil ( bfc ) capable of reducing the soil resistivity with good mixture of retaining capacity and one earthing lead of 20 x 3 c.i. strip, upto switch board ( from apron to switch board, the cost ol g.i. strip will be exrra ) along with 30 cm square c.l. frame with hinged cover & masonry housing. make: as approved in u.p. p.w.d., & c.p.r.i. certified. , supply & laying of 25mm x 3 mm g.i. strip from earth electrode directly in the ground as required complete in all respect. , supply and laying of aluminium conductor pvc insulated armoured served sheathed cables 1100 volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. on surface the cable run shall be fixed on m.s. clamps etc. of suitable size or as directed by the engineer incharge , complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. , 6.00 sqmm 4 core , 25.00 sqmm 3.5 core , 70.00 sqmm 3.5 core , supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting panel tpn switch board complete with the following hrc type heavy duty tpn fuse switches with fuses and instrument chamber etc. complete in all respects. the instrument chamber shall be separate and shall comprise of flush type ammeter, voltmerer, selector switches for ammeter and voltmeter, instrument fuses, current transormer etc. the board shall have suitable capacity electroytic alumininum busbars as per is8623 istulate with heat shrink sleeving and mountend on non hygroscopic supports such as cmc / dmc support with deteachable side covers and shall be suitable for extension on the sides.the switches shall be complete with suitable cable end boxes, reverse entery boxes in case of pedestaal type, cable sockets, compression glands and indicating lamp on incoming etc. the job includes the grounting of the board as per direction of engineer in charge. all coutgoing switches of 100 amp. and above will be provided with ampere metre current transformers and selector switches and instrument fuses etc. the switches board shall be fabricated with crca sheet with a minimum thickness of 1.6 mm / 2 mm. cubicle type switch board shall be of cat a b & b ii and pedestal type for cat b and c only incoming 200 amp. tpn 1 no outgoing 100 amp. tpn 1 no and 63 amp. tpn 3 nos. cat. b. cubicle type , supply and fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn, complete in all respect.40 a tpn , supplying and laying of following size dwc hdpe pipe isi marked along with all accessories like socket, bend, couplers etc.conforming to is 14930, part ii complete with fitting and cutting, jointing etc. in the existing trench, complete as required. , 63 mm dia ( od 63 mm & id 51 mm nominal ) , 90 mm dia ( od 90 mm & id 76 mm nominal ) , supply and fixing of factory wired integral led flood light luminaires with die cast aluminium housing built with dirver set suitable for 140 to 150 watt. confirming to ip 66 protection complete in all respect. ( make twinkle lite equvalent in : havells / neri / juvaas / orient / thor ) , supply & fixing of 16 mtr high mast shaft of approved make with rising system hot dip glavanized inside & out side dip, heaving pole sheet thickness 3 mm. top dia minium 150 mm, bottom dia 360 mm base plate 32 mm thick suitable for wind velocity as per is 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 6 to 12 luminaries & its control gear boxes 1.5 hp power tool moter, 3 point suspension system with steel wire rope 6 mm dia, double drum winch, including making suitable foundation as per manufature drawing / site reuiment along with foundation bolts nuts, washers, anchor plates etc completee in all respect. , supply, installation, testing and commissioning of led rgb / rgbw floodlighting luminaire for facade lighting with die cast aluminium housing, powder coated finish, of following wattage. luminaire shall be capable of producing dynamic color changing light for with 16 million colors by dmx / ethernet based control. the beam angle of the fitting shall be narrow, medium, wide or asymmetric as per the requirement. luminaire shall be complete with driver and capable of operating at line voltage without any separate power supply from 100 270 v ac, 50 hz with power factor > 0.9 . fixture shall be suitable to operate at an ambient temperature range of 10°c to +50°c and shall be ip 65 and ik 06 rated. lifetime shall be at least l70:50000 burning hours at 50°c. luminaire shall be conforming to bis ( is 10322 ) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required. ( make twinklelites / neri / thorn / orient electric ) , 30 w , 45 w / 40 w , 130 w , supply, installation, testing and commissioning of led rgb / rgbw linear wall washer luminaire for facade lighting with aluminium extruded housing, of following wattage. luminaire shall be capable of producing dynamic color changing light with 16 million colors by dmx / ethernet based control. the beam angle of the fitting shall be narrow, medium, wide or asymmetric as per the requirement. luminaire shall be complete with driver and capable of operating at line voltage without any separate power supply from 100 to 270 v ac, 50 hz, power factor > 0.9 . fixture shall be suitable to operate at ambient temperature range of 10°c to +50°c and shall be ip 65 and ik06 rated. lifetime should be at least l70:50000 burning hours at 50°c. luminaire shall be conforming to bis and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required. ( make twinklelites / neri / thorn / orient electric ) , 25 w , 40 w , providing and fixing of signages, modular curved frame technology, of various widths and lengths, to form suggested usages, made of aluminium extruded sections , duly anodised , all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints, of appropriate size and approved make or equivalent. , providing and fixing of signages, customised to the architects design, the signage to be made of 10 mm casted clear acrylic sheet duly cut by laser, all text to be of 2 mm thick acrylic duly laser cut, partially housed and pasted on to engraved surface of the text in the clear acrylic base, the 10mm acrylic sheet to be fixed on 25x25mm section of teak wood with help of crafted ss pins, and further fixed to the priscribed location with the help of wooden dowels, and required adhesive, as per drawing. , providing and fixing prohibition signage, made of aluminium composite panel, and all text and pictograms as screen printed and malamine coated, all fixtures in 304 grade ss, all design as per architects approval. , providing and fixing of exterior signage, to be fixed on the roof top with the help of ms framework, signage to be made of ms pipe frame work, cladded with 3mm aluminium composite panel, duly cut by cnc router, and the letters to be laser cut, 10mm casted clear acrylic, inserted in a cut out fitted on 4 mm 040 casted acrylic, the letters front to be 3m day and night electrocut vinyl, the signage shall illuminated with back lit led, of phillips / ge make of atleast 5yrs gurantee, ( certificate to be provided, by the makers of led ) , complete in all respects , manufacturing, providing & fixing campus entrance signage as per design approved by architect & drawing enclosed, letters extruded on 50 mm. thick red sand stone dry cladding over brick column with varying perimeter 750x750 size with 150 mm. high sand stone pedestal with foundation ll complete as per the specification & directions of the architect. , manufacturing, providing & fixing directional signage vehicular as per design approved by architect & drawing enclosed, letters laser edged on 2 mm. aluminium plate in dark green enamel properly fixed on 6 mm. thick aluminium sheet 900x150 size fixed over 100 150 diameter aluminium dia cast post / ms pole placed over 450 diameter sand stone base 1380 high with foundation all complete as per the specification & directions of the architect. , manufacturing, providing &fixing directional signage pedestrian type a as per design approved by architect & drawing enclosed, letters laser edged on 2 mm. aluminium plate in dark green enamel properly fixed on 50 mm. thick red sand stone slab 1200x200 size fixed over 100 150 diameter aluminium dia cast post / ms pole placed over 2 nos. 150 diameter sand stone post 3000 high with foundation all complete as per the specification & directions of the architect. ) , manufacturing, providing & fixing directional signage pedestrian type b as per design approved by architect & drawing enclosed, letters laser edged on 2 mm. aluminium plate in dark green enamel, properly fixed 100 150 diameter aluminium dia cast post / ms pole 2 nos. properly fixed on 50 mm. thick red sand stone ( i ) slab 1200x200 size & ( ii ) slab 900x300 size placed over 2 nos. 150 diameter sand stone post 3000 high with foundation all complete as per the specification & directions of the architect. , manufacturing, providing & fixing directional signage pedestrian type c as per design approved by architect & drawing enclosed, letters laser edged on 2 mm. stainless steel plate in dark enamel properly fixed on 50 mm. thick red sand stone 900x200 size placed over 150 diameter sand stone post 3000 high with foundation all complete as per the specification & directions of the architect. , manufacturing, providing & fixing directional signage pedestrian type c as per design approved by architect & drawing enclosed, letters laser edged on 2 mm. stainless steel plate in dark enamel properly fixed on 50 mm. thick red sand stone 900x200 size placed over 150 diameter sand stone post 3000 high with foundation all complete as per the specification & directions of the architect. , providing & fixing of signages made on aluminium sheet by cnc cutting as per drawing & design architects approval including all necessary t&p etc all complete in direction of engineer in charge . , providing and fixing of ms gate including moulding, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary ms nuts and bolts complete, with suitable arrangement as per approval of engineer in charge, , providing and fixing bolts including nuts and washers complete. , supplying & filling of cinder asper drawing, design etc all complete in direction of engineer in charge. , labour rate forfilling of boulder pitching ( 40 60 kg ) including wire and necessary lead & lift including transportation etc all complete in direction of engineer in charge. , providing and laying at or near ground level factory made kerb stone of m 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 ( 1 cement: 3 coarse sand ) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5mm ) , including making drainage opening wherever required complete etc. as per direction of engineer in charge ( length of finished kerb edging shall be measured for payment ) . ( precast c.c. kerb stone shall be approved by engineer in charge ) , providing, laying and making kerb channel 30 cm wide and 50 mm thick with cement concrete 1:3:6 ( 1 cement: 3 coarse sand:6 graded stone aggregate 20 mm nominal size ) over 75mm bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth etc. complete and as per direction of engineer in charge. , precast terrazo tiles 22 mm thick with graded marble chips of size upto 12 mm, laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement:4 coarse sand ) : medium shade pigment using 50% white cement and 50% ordinary cement , providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm ( average ) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer in charge : flamed finish granite stone slab jet black, cherry red, elite brown, cat eye or equivalent. , dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with jamuna sand, with common burnt clay non modular bricks. , labour rate for makingfor trimixing on cc road with complete t&p , wiring points for light with 1 sqmm.fr pvc insulated multistrand single core copper condutor cable in pvc conduitpipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq. mm. fr pvc insulated multistrand copper earth contunity wire, piano type switch & ceiling rose / angle / batten holder on 3mm thick phenolic paminated backalite sheet etc.complete in all respects.as directed including matching colour wash. , wiring points for fan / fresh air fan ( light duty exhaust fan ) with 1 sqmm.fr pvc insulated multistrand single core copper condutor cable in pvc conduitpipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq. mm. fr pvc insulated multistrand copper earth contunity wire, piano type switch & ceiling rose on 3mm thick phenolic paminated backalite sheet etc.complete in all respects.as directed including matching colour wash. , wiring points for plug with 1 sqmm.fr pvc insulated multistrand single core copper condutor cable in pvc conduitpipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq. mm. fr pvc insulated multistrand copper earth contunity wire, piano type switch & socketsheet etc.complete in all respects.as directed including matching colour wash. , supply & wiring of submains with 2 nos. 2.5 sq.mm & with 1 no. earth wire of 1.5 sq.mm fr pvc insulated 1100 v grade single core multistrand copper conductor cable inpvc conduitpipe partly concealed including supply of all material, labourand t&p etc. required for proper completion of the work as directed by engineer i / c. , supply and wiring of submain with two number 4 sqmm . fr pvc insulated 1100 v grade multistranded single core copper conductor cable in20mm dia heavy duty ( 2mm thick ) pvc conduitpartly concealed in wall and partly laid in slab along with reinforcement befor concreting with one number 2.5 sqmm fr pvc multistand copper earth contunity wire including colour wash etc. complete in all respects. , supply and wiring of submain 2 number 6 sqmm . fr pvc insulated 1100 v grade multistranded single core copper conductor cable in20mm dia heavy duty ( 2mm thick ) pvc conduit partly concealed in wall and partly laid in slab along with reinforcement befor concreting with one number 4.0 sqmm fr pvc multistand copperearth contunity wire including colour wash etc. complete in all respects. , s / f of hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16swg ms. sheet incorporating 10mm dia, m.s. round bar duly bent for supporting fan hanger dully painted with red oxide and screwing arrangement with wiring conduit laid in the r.c.c roof before concreting along with supply of all materials, labour. t& petc. required for proper completion of the work. , supply and fixing of flush / surface mounting distribution boardswith additional metal door without mcbcomplete in all respects.6 way tpn , supply and fixing of 6 amp to 32 amp mcb ( 10ka ) c curve, 6 32 amps.cat. a , supply and fixing of 40 / 63 amp mcb ( 10ka ) c curve, 63 amp. 4 pole mcb c curve cat. a , supply and fixing of power plug with 15 amp. / 250 volt flush type universal switch and 5 pin 15 a / 250 vflush type universal socket switch on concealed m.s. box including supply of all material, labour t&p etc. required for proper completion of work. , supply and fixing of power plug with 20 amp. / 250 volt flush type universal switch and 5 pin 20 a / 250 vflush type universal socket switch on concealed m.s. box including supply of all material, labour t&p etc. required for proper completion of work. , supply & fixing of single wall bracketon matching m.d.f.e.g.boardbase etc. complete in all required. cat. aa , supply and fixing of led tube light batten fitting suitable for up to 1 x 22 watt led tube light on surface complete in all respect. , supply and fixing of led tube light with batten suitable for up to 1x22 watt led tube light complete including tube etc. on surface complete in all respect. , 1 x 22 w cat aaa , 2 x 22 w cat aaa , supply and fixing of recess / surface / pendent mounting round 10 to 15 watt led down lighter having powder coated die cast aluminium housing with heat sink, diffuser / reflector and driver set complete in all respect . ( category aaa ) , supply and fixing of recess mounting round 15 to 18 watt led down lighter having powder coated die cast aluminium housing with heat sink, diffuser / reflector and driver set complete in all respect. , supply and fixing of 55 watt indoor recess mounting led square fitting for armstrong ceiling having powder coated die cast aluminium housing with body with extended heat sink, diffuser of polycarbonate meterial and driver set complete in all respect. cat aaa , supply &fixingofwater tight oblong 10 watt led bulkhead luminaire with driver set confirming to ip 65 and above protectioncomplete in all respect. , supply of ceilling fans with fan motor of a.c. permanent insulation, capacitor rating conforming bee 5 star rating and is: 374 / 79 abd also comply with is: 1709 / 1984 with latest amendment. the rate voltage 220 / 240 volts, 50hz, 1 ph ac the fan assemble should consist of down rod blades, shackle canopies etc and with double ball bearing system. , supplyfixingofelectronic fan regulator ( modular ) 120 280 v. isimarked, on the existing switch board including making connetion, required material, labour t / p etc for proper completion of work to the satisfaction of engineer in charge of work. , supply & erection ofa.c 230 / 250 volts, 50 hz wall mounted fans including providing m.s bolts, mounting frame and other acessories including connections etc.complete as required300mm sweep as per directionof e / i makebajaj, cromption or equivalent. , supply & fixingof sheet steel enclosure surface / flush mounting fitted with 20 / 32 amp. 2pin and earth metal clad scraping earth plug and socket complete in allrespects as per direction and satisfaction of engineer in charge. cat. a , supply and fixing of 63 a 415 v metal clad tpn cfs complete with hrc fuse etc. on angle iron frame complete in all respect . , supply and burying of 600mm x 600 mmx6mm g.i. plate, vertically for earthing with its top atleast 3 mts. below ground level complete with 20mm g.i.pipe and funnel for watering and two earthing leads of no.8to10swg g.i.wire in 15mm diag.i. pipe upto switch board ( from apron to switch board the cost of g.i. pipe and g.i. wire will be extra ) 30cm. square c.i. frame with hinged cover, masonary housing, alternate layers / of charcoal / coke and salt at least 150mm thick alround etc. complete in all respects. , supply & fixing of two number 8 swg g.i. wire for earthing purpose as required complete in all respects. , supply, installation, testing and commissioning of electrical pane, modular type, front accessible only, free floor standing confirming to minimum ip:43 degree of protection.the panel sheet structure shall undergo seven tank pre treatment process before painting.the sheet steel shall be all of 2.2mm thick crca sheet.all the openable compartments of the panel shall be completely shrouded and provided with padlocking arrangement on all compartments including bus bar and cable alley chambers.the panel height shall not exceed 2200mm and the maximum operating height for any switchgear shall not be more than 1700mm.the panel shall be provided with minimum 75mm base channel frame fabricated from ismc sections.all bus bar links in the panel shall be solid bus bars with coloured pvc shrinkable sleeves, no wires will be acceptable.continuous earth bus shall run alround the panel with earthing studs provided at minimum 2 places.the control wiring shall be carried out with minimum 1.5 / 2.5 sqmm copper wires and adequate number of no / nc, potential free contacts incorporated for remote operation of the starters.proper sized cable termination gland plates shall be provided oncable alleys and knockouts for same shall be provided during fabrication stage itself.the panel shall be provided with a thermostatically controlled heating arrangement ( 200 w ) to take care of high humidity conditions.a 5a socket service outlet ( single phase ) shall be provided in one of the compartments as ervice outlet in the panel.panel shall be so designed at to have minimum 20% spare feeders / space.panel shall undergo epoxy powder coated paint, colour as per is:5 requirement.all cable terminations shall be from top.the complete panel shall be fuse less type, for control circuits 2a / 6a mcbs to be used.all bus bars shall be of aluminium, electrolytic grade only.maximum design density shall not exceed 1 amps / sqmm.all bus bars shall be insulated with coloured heat shrinkable pvc sleeved.all bus bar supports shall be non hygroscopic dmc / smc supports. , the panel shall be manufactured in conformance to requirements of local electrical inspector and it shall be contractors responsibility to get initial approval of drawings and also final approval of complete electrical works related to this section.the minimum clearances between bus bars shall be as follows : phase to phase minimum 20mmphase to neutral minimum 15mma ) 63 amp tnp 2 nos. , or outgoing as per site requirment , providing & fixing m.s. holder bat clamps of approved design to sand cast iron / centrifugally cast ( spun ) iron s & s pipe embeded in & including cement concrete blocks 10x10x10cm. of 1:2:4 mix ( 1 cement : 2 coarse : 4 graded stone aggregate 20mm nominal size ) .including cost of cutting holes & making good the walls etc. , a ) for 100mm dia pipe. , b ) for 75mm dia pipe. , providing & fixingcast iron coller. , a ) 100mm dia. , b ) 75mm dia. , providing & fixing upvc swr bend confirming to is 14735 , 110mm dia , providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete. , a ) 100mm , b ) 75mm , providing and fixing centrifugaly cast iron single equal plain junction of required degree. , 100x100x100mm , 75x75x75mm , providing and fixingcast iron terminal guard. , 100 mm , 75 mm , providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, ( i ) single socketed pipes. , providing &applying high quality acrylic modified resin based texture of dholpur / red sand stone pattern with anti algae and uv resistance properties to be applied as intermediate finish in desired pattern @43.04 kgs / 10 sqm to form film of 1 1.5 mm thickness after scrapping and properly cleaning the surface to remove loose particles from the plaster surface, followed by top coating with premiumacrylic smooth exterior paint with silicone additives of required shade by two or more coats @ 1.43 litres / 10 sqm, complete as the direction of engineer in charge. , structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete , providing and fixing isi marked m.s. pressed butt hinges bright finished with necessary screws etc. complete :125x65x2.12 mm , providing and fixing isi marked oxidised m.s. tower bolt black finish, ( barrel type ) with necessary screws etc. complete 200x10 mm , providing and fixing isi marked oxidised m.s. handles conforming to is:4992 with necessary screws etc. complete 100 mm , providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. , providing and laying pressed clay tiles ( as per approved pattern 20 mm nominal thickness of approved size ) on roofs jointed with cement mortar 1:4 ( 1 cement : 4 coarse sand ) mixed with 2% integral water proofing compound, laid over a bed of 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) and finished neat complete. , wiring point for light with 1.0 sq.mm fr p.v.c. insulated multistrandsingle core copper conductor cable in heavy gauge rigid steel conduit pipepartly concealedin wall&partlylaidin slab along with the reinforcement before concreting complete with 14 s.w.gcopper earth continuity wire&piano typeswitchetc. complete in all respects. , same as in item no. 1 but for fan. and light duty exhaust fan , same as in item no. 1butfor 5ampplug point with piano type switch & socket etc. , add for light / fan points with modular type switches in place of piano type switches , add for plug point with modular switch & socket in place of piano type switch & socket , supply & fixing of power plugwith20amp 250 volts flush type modular switchand 5 pin 20 amp 250 volts flush type universal modular socket on concealed ms box including supply of all material, labour t&p etc. required for proper completion of work , mains & submains supply & wiringofsubmainwithfr p.v.c. insulated1100 volts grade singlecorecopper conductorcable in heavygaugerigid steel coduit partly concealedinwall and partly laid inslab alongwith the reinforcement before concreting complete withone no. 14 swgcopperearth continuity wire complete in all respects. , 2 x 4 sq. mm.in 20 mm dia conduit. , 2 x 10 sq. mm.in 25 mm dia conduit. , s / f of surface / flush mounting spn distribution board ( legrand lexic ) without mcb complete in all respects as directed at site by engineer in charge. 12 ways , supply & fixingof 6 / 10 / 16 / 20 / 25 / 32 amp. sp mcb ( 10 ka ) ( legrand lexic ) , s / f of 40 amp dp mcb ( 10 ka ) ( legrand lexic ) , s / f of sheet steelenclosure for dp / tp / fp mcb with neutral link and earth terminal. , supply&burryingof 600mm x 600mm x 6.0mm g.i. plate, vertically for earthing with its top at least 3 m below ground level complete 20mm dia. g.i.pipe and funnelforwatering and one earthing lead ofno. 8swgg.i. wirein 15 mm dia. gi pipe uptoswitch board ( from apron to switch boardthecost of gi pipe & gi wire willbeextra ) 300mm square c.i. box with hinged cover, masonary housing alternate layer of charcoal / coke and salt atleast 150mm thick alround etc. as per the direction of engineer in charge complete in all respect . , supplying & laying of one number 8 swg g. i. wirein 15 mm. dia. g. i.pipefor earthing, laidin groundor inwall duly concealedincludingthecostofcement, sand, labour, t&pandothermaterial required for proper completion ofthework as directed at site. , supply andlayingofisi marked aluminiumconductor pvc / xlpe insulated armoured, served, sheathed cable 1100volts gradeat 750mmbelow ground level overacushion of 75 mm thick sand around & protected with brick onsides & top on surfacethecablerunshallbe fixed on m.s. clamps etc. of suitablesize completeinallrespect. the armouring of the cable shall be properlyconnectedwith the earth conductor by clamps etc. 10 sqmm 2core , supplyfixing of plam orpintypecopper tin plated cable socket ( lug ) tothecable leads, insulating with tapeand making connections etc. complete in all respects as per direction of engineer in charge. 10 sq.mm. , supply andfixing brass nickle plated compression glandsfor pvc insulated armoured, served, sheathed cable including rubber ring etc.completeinallrespect. the armouring of the cable shall be properlyconnectedwith the earth conductor. 10 sqmm 2core , erection and testing of exhaust fan on the existing hole with suitable size of rag bolts nuts and washers etc complete in all respects. , supply and fixing of 16 gauge ms drum duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respect. , supply & fixing of recess / surface / pendent mounting round10 to 15 watt led down lighter having powder coated die cast aluminium housing with heat silk, diffuser / reflector and driver set complete in all respect. , supply & fixing ofled tube light with batten suitable for upto 1x22 watt led tube light fittings including tube on surface complete in all respect cat aaa , supply & fixing of recess / surface mounting round 24 watt to 32 watt led down lighter having powder coated die cast alumnium housing with extended heat sink, diffuser / reflector and driver set completed in all respect. , supply, laying, jointing, testing and commissioning ofisi marked ( is : 14930, part 2 ) h.d.p.e. ( dwc ) double wall corrugated pipe for cable layinghaving corrugation on outer wall and plain smooth surface at inner side including transportation upto the site, jointing, providing and fixing all fittings i.e. sockets, couplers, reducers, end caps etc including excavation in all kind of soil upto 1 meter depth of suitable width with back filling of soil into trenches tocomplete the works in all respects. ( make : duraline / jain / akg ) 63 mm. id / 78mm od , supply ofac230 / 250 volts, 50 hz fresh airfansincluding providingnuts, bolts, mounting frame and other accessories etc.complete . ( make : bajaj / usha / newtek / havells ) 300 mm sweep , drilling of 200 mm dia bore hole including all necessary t&p etc all complete in direction of engineer in charge. , supply of 125 mm dia mspipe as per is1239including all necessary t&p etc all complete in direction of engineer in charge. , supply of 125 mm dia slotted mspipeincluding all necessary t&p etc all complete in direction of engineer in charge. , supply and fixing of nylon jali around the slotted pipes complete as required including all necessary t&p etc all complete in direction of engineer in charge. , providing and packing of coarse sand / pea gravel around the pipeincluding all necessary t&p etc all complete in direction of engineer in charge. , transport of boring tools other required equipements and installation at site including all necessary t&p etc all complete in direction of engineer in charge. , supply of submersible pump of make ksb ( cora ) for 200 lit / min discharge at 50 meter head with control panel, support wire etc complete including all necessary t&p etc all complete in direction of engineer in charge. , providing 3 core pvc insulated submersible cable. ( from pump panel to submersible pump ) including all necessary t&p etc all complete in direction of engineer in charge. , providing and fixing 65 mm dia. g.i. pipe complete with fittings and clamps including cutting and making good the wall etc. ( from submersible pump to ground level ) including all necessary t&p etc all complete in direction of engineer in charge. , providing and fixing 65 mm dia. brass gate valve with ci wheel of approved qualityincluding all necessary t&p etc all complete in direction of engineer in charge. , lowering of 125 mm dia ms pipe in bore hole including cutting, jointing etc completeincluding all necessary t&p etc all complete in direction of engineer in charge. , supply and fixing of tube well accessories i.e. well cap, clips, clamps, etc. to complete the job in all respectincluding all necessary t&p etc all complete in direction of engineer in charge. , fixing, testing and commissioning for erection and lowering of submersible pump, 65 mm dia gi column pipe, 3 coresubmersible copper cable upto the control panel, supporting clamps, cable clips, pressure gauge, connection line and all other accessories required for the proper completion of the work. , testing and development of tube wellincluding all necessary t&p etc all complete in direction of engineer in charge. , mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods, gratings etc. ( when not included in an over all rates ) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of z section , mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods, gratings etc. ( when not included in an over all rates ) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. , mild steel or iron work of small sizes and sections such as trusses built up gates, door frames, record racks , roof work, gates etc etc.wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of grills , providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including isi marked stainless steel butt hinges with necessary screws , providing and fixing factory made upvc white colour casement / casement cum fixed glazed door comprising of upvc multi chambered frame, sash and mullion ( where ever required ) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length ( shape & size according to upvc profile ) , upvc extruded glazing beads of appropriate dimension, epdm gasket, zinc alloy ( white powder coated ) 3d hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, g.i fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion ( if required ) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of engineer in charge. ( single / double glass panes and silicon sealent shall be paid separately ) . note: for upvc frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. three track three panels sliding window with fly proof s.s wire mesh ( two nos. glazed & one no. wire mesh panels ) made of ( big series ) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. ( area of window above 1.75 sqm , providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing epdm gasket, perforated aluminium spacers, desiccants, sealant ( both primary and secondary sealant ) etc. as per specifications, drawings and direction of engineer in charge complete. ( make saint gobain / asahi / modigardian ) , providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3kg / sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm , providing and fixing stainless steel ( grade 304 ) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, i / c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer incharge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. ) . , providing and laying integral cement based waterroofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a ) applying a slurry coat of neat cement using 2.75 kg / sqm of cement admixed with water proofing compound conforming to is. 2645 and approved by engineer in charge over the rcc slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b ) laying brick bats with mortar using broken bricks / brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 ( 1 cement : 5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge over 20 mm thick layer of cement mortar of mix 1:5 ( 1 cement :5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c ) after two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed jointless cement mortar of mix 1:4 ( 1 cement :4 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e ) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. all above , providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. , providing and fixing bright finished brass door latch with necessary screws etc. complete : 250x16x5 mm , providing and fixing bright finished brass tower bolts ( barrel type ) with necessary screws etc. complete : , ( a ) 250 mm x 10mm , ( a ) 200 mm x 10mm , providing and fixing bright finished brass handles with screws etc. complete:125 mm , providing and fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ) , with necessary accessories and screws etc. complete. , add for plaster drip course in plastered surface or moulding to r.c.c. projections. , providing and fixing panic bar / latch ( double point ) fitted with a single body, trim latch & lock on back side of the panic latch of reputed brand and manufacture to be approved by the engineer in charge, all complete. , providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from m.s. sheets and galvanized with zinc coating of 120 gms / sqm ( both side inclusive ) as per is : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate g.i. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to g.i. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long g.i. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall / partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c / c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the engineer in charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to is: 2095 ( part i ) : 2011 ( board with bis certification marks ) , providing & fixing armstrong or equivalent vertical linear baffle ceiling made out of aluminum extrusion in aluminum alloy grade 6063. the baffle blade shall be in size of 100x25x3600mmin cherry / red oak finish with spacing of 100mm. the baffle blade shall be suspended using slotted u profile at on center spacing in multiples of 25mm. longer lengths of baffle to be connected by baffle joiner and the ends to be fixed with end caps. installation of u grid: the u profile to be suspended at every 1200mm on centre using 6mm threaded rod from the structural soffit using u profile hanger. u profile splice to be used to join more than one u profiles of length 3.75m. 1st u grid channel must be no more than 400mm from the perimeter. installation of armstrong baffles: locate the slot for baffle hangers in slot of baffle section at 1200mm centres. hangers are inserted into the slot, then rotated 90° and fixed into position by tightening the grub screw. baffle to be lifted into position and hangers engage over lip of u grid channel. each hanger to be secured into position by inserting the locking clip. baffles blades to be connected at ends with baffle joiner, which are inserted into the top and bottom slots of the , providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to is:3614 ( part ii ) , tested and certified as per laboratory approved by engineer in charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 swg g.i.sheet ( zinc coating not less than 120 gm / m2 ) duly filled fr insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of engineer in charge , providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete. fixed to steel windows by welding , providing and fixing partition upto ceiling height consisting of g.i. frame and required board, including providing and fixing of frame work made of special section power pressed / roll form g.i. sheet with zinc coating of 120 gms / sqm ( both side inclusive ) , consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. the boards are to be fixed to the frame work with joints staggered to avoid through cracks, m.s. fixing channel of 99 mm width ( 0.9 mm thick having two flanges of 9.5 mm each ) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners ( 25 mm x 25 mm x 0.5 mm ) , joint finisher and two coats of primer suitable for board as per manufactures specification and direction of engineer in charge all complete. 66mm overall thickness partition using 8mm thick double skin multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process ( high pressure steam cured ) as per is : 14862 with suitable fibre cement screws , providing and fixing factory made upvc door frame made of upvc extruded sections having an overall dimension as below ( tolerance ±1mm ) , with wall thickness 2.0 mm ( ± 0.2 mm ) , corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. the hinge side vertical of the frames reinforced by galvanized m.s. tube of size 19 x 19 mm and 1mm ( ± 0.1 mm ) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of engineerin charge extruded section profile size 48x40 mm , 24 mm thick factory made pvc door shutters made of styles and rails of a upvc hollow section of size 59x24 mm and wall thickness 2 mm ( ± 0.2 mm ) with inbuilt edging on both sides. the styles and rails mitred and joint at the corners by means of m.s. galvanised / plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. the styles of the shutter reinforced by inserting galvanised m.s. tube of size 20x20 mm and 1 mm ( ± 0.1 mm ) wall thickness. the lock rail made up of h section, a upvc hollow section of size 100x24 mm and 2 mm ( ± 0.2 mm ) wall thickness, fixed to the shutter styles by means of plastic / galvanised m.s. u cleats. the shutter frame filled with a upvc multi chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ( ± 0.1 mm ) wall thickness. the panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised m.s. rod and fastened with nuts and washers, complete as per manufacturers specification and direction of engineer in charge. ( for w.c. and bathroom door shutter ) , wiring points for light with 1 sqmm.fr pvc insulated multistrand single core copper condutor cable in pvc conduitpipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq. mm. fr pvc insulated multistrand copper earth contunity wire, piano type switch & ceiling rose / angle / batten holder on 3mm thick phenolic paminated backalite sheet etc.complete in all respects.as directed including matching colour wash. , wiring points for fan / fresh air fan ( light duty exhaust fan ) with 1 sqmm.fr pvc insulated multistrand single core copper condutor cable in pvc conduitpipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq. mm. fr pvc insulated multistrand copper earth contunity wire, piano type switch & ceiling rose on 3mm thick phenolic paminated backalite sheet etc.complete in all respects.as directed including matching colour wash. , wiring points for plug with 1 sqmm.fr pvc insulated multistrand single core copper condutor cable in pvc conduitpipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq. mm. fr pvc insulated multistrand copper earth contunity wire, piano type switch & socketsheet etc.complete in all respects.as directed including matching colour wash. , supply & fixing ofbuzzer on polished mdfeg / teak ply board including making connections etc. complete in all respect. , supply & wiring of submains with 2 nos. 2.5 sq.mm & with 1 no. earth wire of 1.5 sq.mm fr pvc insulated 1100 v grade single core multistrand copper conductor cable inpvc conduitpipe partly concealed including supply of all material, labourand t&p etc. required for proper completion of the work as directed by engineer i / c. , supply and wiring of submain with two number 4 sqmm . fr pvc insulated 1100 v grade multistranded single core copper conductor cable in20mm dia heavy duty ( 2mm thick ) pvc conduitpartly concealed in wall and partly laid in slab along with reinforcement befor concreting with one number 2.5 sqmm fr pvc multistand copper earth contunity wire including colour wash etc. complete in all respects. , supply and wiring of submain 2 number 6 sqmm . fr pvc insulated 1100 v grade multistranded single core copper conductor cable in20mm dia heavy duty ( 2mm thick ) pvc conduit partly concealed in wall and partly laid in slab along with reinforcement befor concreting with one number 4.0 sqmm fr pvc multistand copperearth contunity wire including colour wash etc. complete in all respects. , s / f of hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16swg ms. sheet incorporating 10mm dia, m.s. round bar duly bent for supporting fan hanger dully painted with red oxide and screwing arrangement with wiring conduit laid in the r.c.c roof before concreting along with supply of all materials, labour. t& petc. required for proper completion of the work. , supply and fixing of flush / surface mounting distribution boardswith additional metal door without mcbcomplete in all respects.6 way tpn , supply and fixing of 6 amp to 32 amp mcb ( 10ka ) c curve 6 32 amps.cat. a , supply and fixing of 40 / 63 amp mcb ( 10ka ) c curve 63 amp. 4 pole mcb c curve cat. a , supply and fixing of power plug with 15 amp. / 250 volt flush type universal switch and 5 pin 15 a / 250 vflush type universal socket switch on concealed m.s. box including supply of all material, labour t&p etc. required for proper completion of work. , supply and fixing of power plug with 20 amp. / 250 volt flush type universal switch and 5 pin 20 a / 250 vflush type universal socket switch on concealed m.s. box including supply of all material, labour t&p etc. required for proper completion of work. , supply & fixing of single wall bracketon matching m.d.f.e.g.boardbase etc. complete in all required. cat. aa , supply and fixing of led tube light batten fitting suitable for up to 1 x 22 watt led tube light on surface complete in all respect. , supply and fixing of led tube light with batten suitable for up to 1x22 watt led tube light complete including tube etc. on surface complete in all respect. , 1 x 22 w cat aaa , 2 x 22 w cat aaa , supply and fixing of recess / surface / pendent mounting round 10 to 15 watt led down lighter having powder coated die cast aluminium housing with heat sink, diffuser / reflector and driver set complete in all respect . ( category aaa ) , supply and fixing of recess mounting round 15 to 18 watt led down lighter having powder coated die cast aluminium housing with heat sink, diffuser / reflector and driver set complete in all respect. , supply and fixing of 55 watt indoor recess mounting led square fitting for armstrong ceiling having powder coated die cast aluminium housing with body with extended heat sink, diffuser of polycarbonate meterial and driver set complete in all respect. cat aaa , supply &fixingofwater tight oblong 10 watt led bulkhead luminaire with driver set confirming to ip 65 and above protectioncomplete in all respect. , supply of ceilling fans with fan motor of a.c. permanent insulation, capacitor rating conforming bee 5 star rating and is: 374 / 79 abd also comply with is: 1709 / 1984 with latest amendment. the rate voltage 220 / 240 volts, 50hz, 1 ph ac the fan assemble should consist of down rod blades, shackle canopies etc and with double ball bearing system. , supplyfixingofelectronic fan regulator ( modular ) 120 280 v. isimarked, on the existing switch board including making connetion, required material, labour t / p etc for proper completion of work to the satisfaction of engineer in charge of work. , supply & erection ofa.c 230 / 250 volts, 50 hz exhaust fans including providing m.s bolts, mounting frame and other acessories including connections etc.complete as required300mm sweep as per directionof e / i makebajaj, cromption or equivalent. , supply & fixingof sheet steel enclosure surface / flush mounting fitted with 20 / 32 amp. 2pin and earth metal clad scraping earth plug and socket complete in allrespects as per direction and satisfaction of engineer in charge. cat. a , supply and fixing of 63 a 415 v metal clad tpn cfs complete with hrc fuse etc. on angle iron frame complete in all respect . , supply and burying of 600mm x 600 mmx6mm g.i. plate, vertically for earthing with its top atleast 3 mts. below ground level complete with 20mm g.i.pipe and funnel for watering and two earthing leads of no.8to10swg g.i.wire in 15mm diag.i. pipe upto switch board ( from apron to switch board the cost of g.i. pipe and g.i. wire will be extra ) 30cm. square c.i. frame with hinged cover, masonary housing, alternate layers / of charcoal / coke and salt at least 150mm thick alround etc. complete in all respects. , supply & fixing of two number 8 swg g.i. wire for earthing purpose as required complete in all respects. , providing and placing on terrace ( at all floor levels ) polyethylene water storage tank isi : 12701 marked with cover and suitable locking arrangement and makingnecessaryholes for inlet, outlet and overflow pipes but without fittingandbasesupportfor tank. 750 litres capacity , s / f of 100 mm dia g.i pipe b class for cable completed with supports by 3 nos. clamp made for 20x30 mm ms flat and suitable size of nutbolt & washer required for proper completion of worh as per direction of e / i. , supply and laying of aluminium conducter pvc insulated armoured served sheathed cables 1100 volts grate at a depth of below ground lvl overa cusion of 75 mm thick sand alroundand protected with burnt on side and on top , on surface the cable run shallbe fixed on m.s clamps etc. of suitable size or as directed by e / i complete in all respects, the armouring of the cable shall be properly connected with the earth conductor by clamps atc. , ( i ) 10 sq. mm 2core , ( ii ) 16 sq. mm 4 core , ( iii ) 70 sq. mm 3.5 core , ( iv ) 120 sq. mm 3.5 core , supply 7 fixing of plain or pin type copper tin plated cable socket to the cable leads, insulated with tape and making connection etc. complete in all respect as per direction of e / i , ( i ) 10 sq. mm , ( ii ) 16 sq. mm , ( iii ) 35 sq. mm , ( iv ) 70 sq. mm , ( iv ) 120 sq. mm , providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre / 6 litre ( adjustable to 4 litre / 8 litres ) , including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. water closet of size 780x370x690 mm , providing and fixing white vitreous china pedestal type water closet ( european type ) with seat and lid, 10 litre low level white vitreous china flushing cistern & c.p. flush bend with fittings & c.i. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : w.c. pan with isi marked white solid plastic seat and lid , providing and fixing water closet squatting pan ( indian type w.c. pan ) with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) conforming to is : 7231, with all fitting and fixtures completed including cutting and making good the walls and floors wherever required. white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests , providing and fixing wash basin with c.i. brackets, 15 mm dia cp brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required: ( a ) white vitreous china wash basin size 550x400 mm with a 15 mm cp brass single hole basin mixer , providing and fixing flexible p.v.c. waste pipe for sink or wash basin including pvc waste fittings complete. , 32 mm dia ( for wash basin ) , 40 mm dia ( for sink and urinal ) , providing & fixing stainless steel aisi 304 ( 18 / 8 ) kitchen sink with drain board as per is :13983 with c.i. bracketsandstainless steel plug 40 mm including painting of fittings and brackets cutting and making good the walls wherever required. 510x1040 mm bowl depth 200 mm , providing & fixing 600 x 450 mm bevelled edge mirror of superiorglass ( of approved quality ) complete with 6mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. , providing & fixing viterous china toilet paper holder. , providing & fixing white vitreous china water less urinal of size 600 x 330 x 315 mm having antibacterial / germs free ceramic surface, fixed with cartridge having debris catcher and hygiene seal , providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size ) as per direction of engineer in charge and finished smooth. granite stone of approved shade , providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand ) , joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. granite of any colour and shade area of slab over 0.50 sqm , providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms , providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. , providing and fixing ptmt grating of approved quality and colour. circular type:125 mm nominal dia with 25 mm waste hole , providing & fixing soil, waste and vent pipes. , a ) 100mm dia centrifugally cast iron s & s pipe. , b ) 75mm dia centrifugally cast iron s & s pipe. , providing lead caulked joints to sand cast iron / centrifugally cast ( spun ) iron pipes & fittings of diameters. , 100 mm , 75 mm , providing & fixing m.s. holder bat clamps of approved design to sand cast iron / centrifugally cast ( spun ) iron s & s pipe embeded in & including cement concrete blocks 10x10x10cm. of 1:2:4 mix ( 1 cement : 2 coarse : 4 graded stone aggregate 20mm nominal size ) .including cost of cutting holes & making good the walls etc. , a ) for 100mm dia pipe. , b ) for 75mm dia pipe. , providing & fixingcast iron coller. , a ) 100mm dia. , b ) 75mm dia. , providing & fixing upvc swr bend confirming to is 14735 , 110mm dia , providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete. , a ) 100mm , b ) 75mm , providing and fixing centrifugaly cast iron single equal plain junction of required degree. , 100x100x100mm , 75x75x75mm , providing and fixingcast iron terminal guard. , 100 mm , 75 mm , providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, ( i ) single socketed pipes. , providing and fixinggi pipes complete with gi fittings and clamps, including cutting and making good walls etc. ( internal work ) . internal work exposed on wall , 15mm dia nominal bore , 20mm dia nominal bore , 25mm dia nominal bore , 32mm dia nominal bore , painting gi pipes and fittings with synthetic enamel paint over a ready mixed priming coat, both of approved quality for new work. , 15mm dia nominal bore , 20mm dia nominal bore , 25mm dia nominal bore , 32mm dia nominal bore , concealed pipe including painting with anticorrosive bitumatic paint, cutting chases and making good the wall. ( internal work ) exposed on wall , a ) 15mm dia nominal outer dia pipes , a ) 20mm dia nominal outer dia pipes , providing & fixing gun metal gate valve with c.i. wheel of approvedquality ( screwed end ) , 25 mm nominal bore , 32 mm nominal bore , providing and fixing ballvalve ( brass ) of approved quality complete. ( high or low pressure with plastic floats ) . 25 mm nominal bore , providing&fixing15 mm nominal bore45 cm long unplasticised pvc connection pipewith brass unions. , providing & fixing 15 mm nominal bore cp brass bib cockof approved quality conformingtois 8931. , providing and fixing 15 mm nominal bore c.p brass long nose bib cock of approved qualityconforming to is standardsandweighing notlessthan 810 gms. , providing & fixing 15 mm nominal bore c.p brass angle valve for basin mixer and geyser points of approved quality conformingto is8931. , excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m.including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m. a ) pipes 80mm to 300mm diameter. , providing, laying and joining glazed stone ware pipes grade awith stiff mixture of cement mortar in the proportion of 1:1 ( 1 cement : 1 fine sand ) including testing of joints etc. complete.150mm diameter , providing & laying cement concrete 1:5:10 ( 1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size ) alround s.w. pipes including bed concrete as per standard design. 150mm diameter , constructing brick masonry manhole in cement mortar 1:4 ( 1 cement :4 coarse sand ) rcc top slab with 1:2:4 mix ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size ) , foundation concrete 1:4:8 mix ( 1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size ) inside plastering 12mm thick with cement mortar 1:3 ( 1 cement :3 coarse sand ) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size ) finished with a floating coat of neat cement complete as per standard design inside size 90x80cms and 45cms deep including ci cover with frame ( light duty ) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg ( weight of cover 23 kg and weight of frame 15kg ) . with fps bricks of class designation 75 , ( i ) for sewer line , extra for depth of man hole size 90x80 cm , providing and fixing square mouths. w. gully trapgrade `a complete with c.i. gratingbrickmasonry chamber with f.p.s bricks and water tight ci cover with frame of 300 x 300 mm size ( inside ) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 180 x 150 mm. size p type , providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per is : 10910 on 12mm dia steel bar conforming to is: 1786 having minimum cross section as 23 mm x25mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protruded legs having 2mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacturess permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size ) complete as per design. , providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including isi marked stainless steel butt hinges with necessary screws , providing and fixing carbon steel galvanised ( minimum coating 5 micron ) dash fastener of 10 mm dia double threaded 6.8 grade ( yield strength 480 n / mm2 ) , counter sunk head, comprising of 10 mm dia polyamide pa 6 grade sleeve, including drilling of hole in frame , concrete / masonry, etc. as per direction of engineer in charge. , frame anchor hrd c 10x140 , frame anchor hrd c 10x120 , frame anchor hrd c 10x120 , providing and fixing 1st quality ceramic glazed floor tiles conforming to is : 15622 ( thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. , providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. , kota stone slab flooring over 20 mm ( average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand ) : 25 mm thick , kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm ( average ) thick cement mortar 1:3 ( 1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. , providing and laying integral cement based waterroofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a ) applying a slurry coat of neat cement using 2.75 kg / sqm of cement admixed with water proofing compound conforming to is. 2645 and approved by engineer in charge over the rcc slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b ) laying brick bats with mortar using broken bricks / brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 ( 1 cement : 5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge over 20 mm thick layer of cement mortar of mix 1:5 ( 1 cement :5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c ) after two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed jointless cement mortar of mix 1:4 ( 1 cement :4 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e ) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. all above , providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. , providing and fixing bright finished brass door latch with necessary screws etc. complete : 250x16x5 mm , providing and fixing bright finished brass tower bolts ( barrel type ) with necessary screws etc. complete : , ( a ) 250 mm x 10mm , ( a ) 200 mm x 10mm , providing and fixing bright finished brass handles with screws etc. complete:125 mm , providing and fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ) , with necessary accessories and screws etc. complete. , supplying & intallation of tesnsile fabric canopy make serge ferrari / mehlar including all necessary t&p etc all complete in direction of engineer in charge. , providing and fixing wash basin with c.i. brackets, 15 mm dia cp brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required: ( a ) white vitreous china wash basin size 550x400 mm with a 15 mm cp brass single hole basin mixer , providing and fixing flexible p.v.c. waste pipe for sink or wash basin including pvc waste fittings complete. , 32 mm dia ( for wash basin ) , 40 mm dia ( for sink and urinal ) , providing & fixing stainless steel aisi 304 ( 18 / 8 ) kitchen sink with drain board as per is :13983 with c.i. bracketsandstainless steel plug 40 mm including painting of fittings and brackets cutting and making good the walls wherever required. 510x1040 mm bowl depth 200 mm , providing & fixing 600 x 450 mm bevelled edge mirror of superiorglass ( of approved quality ) complete with 6mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. , providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size ) as per direction of engineer in charge and finished smooth. granite stone of approved shade , providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws withconcealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms , providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. , providing and fixing ptmt grating of approved quality and colour. circular type:125 mm nominal dia with 25 mm waste hole , providing & fixing soil, waste and vent pipes. , a ) 100mm dia centrifugally cast iron s & s pipe. , b ) 75mm dia centrifugally cast iron s & s pipe. , providing lead caulked joints to sand cast iron / centrifugally cast ( spun ) iron pipes & fittings of diameters. , 100 mm , 75 mm , providing & fixing m.s. holder bat clamps of approved design to sand cast iron / centrifugally cast ( spun ) iron s & s pipe embeded in & including cement concrete blocks 10x10x10cm. of 1:2:4 mix ( 1 cement : 2 coarse : 4 graded stone aggregate 20mm nominal size ) .including cost of cutting holes & making good the walls etc. , a ) for 100mm dia pipe. , b ) for 75mm dia pipe. , providing & fixingcast iron coller. , a ) 100mm dia. , b ) 75mm dia. , providing & fixing upvc swr bend confirming to is 14735, 110mm dia , providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete. , a ) 100mm , b ) 75mm , providing and fixing centrifugaly cast iron single equal plain junction of required degree. , 100x100x100mm , 75x75x75mm , providing and fixingcast iron terminal guard. , 100 mm , 75 mm , providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, ( i ) single socketed pipes. , providing and fixinggi pipes complete with gi fittings and clamps, including cutting and making good walls etc. ( internal work ) . internal work exposed on wall , 15mm dia nominal bore , 20mm dia nominal bore , 25mm dia nominal bore , 32mm dia nominal bore , painting gi pipes and fittings with synthetic enamel paint over a ready mixed priming coat, both of approved quality for new work. , 15mm dia nominal bore , 20mm dia nominal bore , 25mm dia nominal bore , 32mm dia nominal bore , concealed pipe including painting with anticorrosive bitumatic paint, cutting chases and making good the wall. ( internal work ) i ) exposed on wall , a ) 15mm dia nominal outer dia pipes , a ) 20mm dia nominal outer dia pipes , providing & fixing gun metal gate valve with c.i. wheel of approvedquality ( screwed end ) , 25 mm nominal bore , 32 mm nominal bore , providing and fixing ballvalve ( brass ) of approved quality complete. ( high or low pressure with plastic floats ) . 25 mm nominal bore , providing&fixing15 mm nominal bore45 cm long unplasticised pvc connection pipewith brass unions. , providing & fixing 15 mm nominal bore cp brass bib cockof approved quality conformingtois 8931. , providing and fixing 15 mm nominal bore c.p brass long nose bib cock of approved qualityconforming to is standardsandweighing notlessthan 810 gms. , providing & fixing 15 mm nominal bore c.p brass angle valve for basin mixer and geyser points of approved quality conformingto is8931. , providing and placing on terrace ( at all floor levels ) polyethylene water storage tank isi : 12701 marked with cover and suitable locking arrangement and makingnecessaryholes for inlet, outlet and overflow pipes but without fittingandbasesupportfor tank. 750 litres capacity , excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m.including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m.a ) pipes 80mm to 300mm diameter. , providing, laying and joining glazed stone ware pipes grade awith stiff mixture of cement mortar in the proportion of 1:1 ( 1 cement : 1 fine sand ) including testing of joints etc. complete. 150mm diameter , providing & laying cement concrete 1:5:10 ( 1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size ) alround s.w. pipes including bed concrete as per standard design. 150mm diameter , constructing brick masonry manhole in cement mortar 1:4 ( 1 cement :4 coarse sand ) rcc top slab with 1:2:4 mix ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size ) , foundation concrete 1:4:8 mix ( 1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size ) inside plastering 12mm thick with cement mortar 1:3 ( 1 cement :3 coarse sand ) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size ) finished with a floating coat of neat cement complete as per standard design . inside size 90x80cms and 45cms deep including ci cover with frame ( light duty ) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg ( weight of cover 23 kg and weight of frame 15kg ) . with fps bricks of class designation 75 , ( i ) for sewer line , extra for depth of man hole size 90x80 cm , providing and fixing square mouths. w. gully trapgrade `a complete with c.i. gratingbrickmasonry chamber with f.p.s bricks and water tight ci cover with frame of 300 x 300 mm size ( inside ) the weight of cover to be not less than 4.50 k.g and frame to be not less than 2.70 kg as per standard design. 180 x 150 mm. size p type , providing & fixing of 50 mm thick grc jali including grout in brick wall as per drawing & design and approval of architect in charge. , poster frame ( f 1 ) size=0.45x0.55mt. providing teak wood frame around the poster with 6mmcommercial ply i.s. 5509 ( greenply / century, ) back, frame shall be pu polished and 6mm thick glass as cover with patch fittings etc all complete in direction of architect in charge. refer drg , frame ( f 2 ) size=0.24x0.34mt. providing teak wood frame around the poster with 6mmcommercial ply i.s. 5509 ( greenply / century, ) back, frame shall be pu polished and 6mm thick glass as cover with patch fittings etc all complete in direction of architect in charge. refer drg , false ceiling providing & fixing of armstrong false ceiling make armstrong sound scape hexagon shape traffic white scrim with embedded frames 1200x1200x 30mm including frame &panel etc all complete in direction of engineer in charge. , providing & fixing of armstrong false ceiling silhouette including frame & panel etc all complete in direction of engineer in charge. , gypsum partition providing and laying gypsum panel partitions 100 mm thick with water proof gypsum panels of size 666x500x100 mm, made of calcite phosphor gypsum fixed with tongue and groove, jointed with bonding plaster as per manufacturer’s specifications in superstructure above plinth level up to floor v level. gypsum blocks will have a minimum compressive strength of 9.3 kg / cm2 ( dsr 6.40 ) , suppying testing & commissioning of water coolar with water storage tank capcity 50 litre per hour including stabilizer with stand and water suuply pipe & copper cabling & drain pipe etc all complete in direction of engineer in charge. ( make blue star / eurekforbes ) , reception table with18 mm thick ply with veneer top of size 1.00 mtr x0.600 mtr the edge finish with corner bevelled as per the design specified in the drawing planks fixed on the frame of 18 mm thick ply also providing 3 nos. sliding storage shelf made with commercial ply i.s. 5509 ( greenply / century, ) of 12mm thick planks design as per drawing, shelf track of 25mm thick ply . &legs made in teak wood height 0.75 mtr size varying as per design. smooth edge finished all including moulding & carving as described in the drawing and pu polishedetc all complete in direction of architect in charge. , reception chair medium back rest chair without arm, back rest finish all in teak wood, chair have all finished in teak wood as per drawing . high quality linen fabric at least 800.00 rs. per rmt with cushion on both seat and back. legs all made in teak wood all edge smooth finished. all include moulding, carving and beadings as per design and pu polished etc all complete in direction of architect in charge. ( size=0.45x0.45x.045mt. ) , table lockertable with 18mm thickcommercial ply i.s. 5509 ( greenply / century, ) of size 2.10 mtr x0.60 mtr the edge finish with corner bevelled as per the design specified in the drawing planks fixed on the frame of 130x45mm thick teak wood also providing 10 nos. sliding storage shelf ( 325x450mm ) in two layers made with teak wood of 19mm thick planks design as per drawing, shelf track of 15mm thick teak wood . &legs made in teak wood height 1.00 mtr size30x45xmmvarying as per design. smooth edge finished all including moulding & carving & necessary fittings handle & locks etc, as described in the drawing. , size=1x0.45x1.5mt. almira as per drawing with 4mm veneerover 19 mm ply water proof plywood ( conforming to international formaldehyde emission standards ) and teak wood beading finished edgesandinner surface finished with 4mm veneeras / shade approved by the architect / in charge. the shuttershall be of teak woodwith glass / teakwood panel as per drawings. the almira shall be pu polished etc all complete in direction of architect in charge. , size=0.6x0.6x0.45mt. teak wood batten planter with 3mm brass metal case to hold clay pot and planter, planter shall be pu polished etc all complete in direction of architect in charge. refer drg , size=1.65x0.8x0.45mt. teak wood batten planter with 3mm brass metal case to hold clay pot and plantershall be pu polished etc all complete in direction of architect in charge. refer drg , size=3.00x0.75x1.35 mt. providing teakwood framing on the edge of shelf with shutter panels with glass. providing fittings ( dorma or equvellantglass to glass hinges 2 nos. 180*, door knob 1 no., glass to glass connector 180* 4 nos., glass to glass connector 90* 20 nos., glass to wall connector 90* 12 nos, 12mm thick toughened glass with silicone including installation etc all complete in direction of architect in charge. , providing and fixing of 8mm thick sun board panel, using 8 mmcommercial ply i.s. 5509 ( greenply / century, ) as base with teak beading on edge as per drawing. the display material has to be printed on vinyl film lg / garware / 3m film and pasted on the glass. etc all complete in direction of architect in charge. ref. drg. , providing and fixing of 12 mm thick toughened glass panel of specified size using hardware fittings namely steel studs as per drawing. the display material has to be printed on lg / garware / 3m film and pasted on the glass.etc all complete in direction of architect in charge. ref. drg. , size=3.0x0.75x1.35mt. tableas per drawing teak wooden plank tableand teak beading finished edges. providing fittings ( dorma or equvellant ) glass to glass hinges 2 nos. 180*, door knob 1 no., glass to glass connector 180* 4 nos., glass to glass connector 90* 20 nos., glass to wall connector 90* 12 nos, 12mm thick toughened glass with silicone including installation etc all complete in direction of architect in charge.refer drg. , size=3.3x0.6x1.52mt. diorama display boxteak wooden frameand teak beading finished edges. including providing & fixing of6mm glass on 1 side for display including patch fittings etc all complete in direction of architect in charge.. refer drg. , supply and fixing of gazeebo ( 3.50 mtr dia ) octagonal shape and 3.0 mtr height and tata blue scope roof with frame as per drawing including grouting of cast iron column in r.c.c block ( size 450mmx450mmx450mm ) and gazebo floor vitrified tile and cast iron railing 900 mm high with painting and entry in one side and including one coat primer & painting, polishing including all necessary t& p etc. all complete in direction of engineer in charge. , providing & fixingof sand stone single piece slab ornamental benches size 1500x500 mm and height 400 mm of approved design pattern ( shape ) and specifications includingcement concrete1 :2 :4 grouting, all materials, labor and t & p etc. required for proper completion of work as directed by architect in charge. , providing & fixingofmild steel benches size 1500x500 mm and height 400 mm of approved design andspecifications with paining polidhingincludingcement concrete1 :2 :4 grouting, all materials, labor and t & p etc. required for proper completion of work as directed by architect in charge. , fabrication and supply & fixing of stainless steel grade, sheet thickness = 1.2 mm, double dustin situable for air port, park, metor stations etc.with civil work including all necessary t&p etc all complete in direction of engineer in charge. ( model no. ozuf db bo lid, make ozone / jindal / j.c.decaux or equivalent ) , suppying testing & commissioning of water coolar with water storage tank capcity 50 litre per hour including stabilizer with stand and water suuply pipe & copper cabling & drain pipe etc all complete in direction of engineer in charge. ( make blue star / eurekforbes ) , suppying testing & commissioning of split a.c. 1.5 tonne including indoor & outdoor unitincluding stabilizer with stand & copper cabling & drain pipe etc all complete in direction of engineer in charge. ( make daikin / hitachi / o genral ) , supplying and fixing of duplex maps d03 outdoor playing equipment ( make arihant / kompain ) including necessaryfittings, t&p etc all complete in direction of engineer in charge. , supplying and fixing of four seater arc swing outdoor playing equipment ( make arihant / kompain ) including necessaryfittings, t&p etc all complete in direction of engineer in charge. , supplying and fixing of multi seater see saw outdoor playing equipment ( make arihant / kompain ) including necessaryfittings, t&p etc all complete in direction of engineer in charge. , supplying and fixing of cystal maze outdoor playing equipment ( make arihant / kompain ) including necessaryfittings, t&p etc all complete in direction of engineer in charge. , supplying and fixing of turbo tower outdoor playing equipment ( make arihant / kompain ) including necessaryfittings, t&p etc all complete in direction of engineer in charge. , supplying and fixing ofcurve loop climber outdoor playing equipment ( make arihant / kompain ) including necessaryfittings, t&p etc all complete in direction of engineer in charge. , supplying and fixing of balancing bridge ( model no pgth 03 ) outdoor playing equipment ( make arihant / kompain ) including necessaryfittings, t&p etc all complete in direction of engineer in charge. , supplying and fixing of four seater mgr outdoor playing equipment ( make arihant / kompain ) including necessaryfittings, t&p etc all complete in direction of engineer in charge. , supplying & laying of sand mixed gravels including all necessary lead & lift with compaction etc all complete in direction of engineer in charge. , supplying & laying of graced stone chips ( 22 4 53 gauge stone ) including all necessary lead & lift with compaction etc all complete in direction of engineer in charge. , supplying & laying of drainage composite for use behind walls, between two different fills, alongside drains of road, below concrete lining of canals etc. geocomposite for planar drainage, realized by thermobonding a draining core in extruded monofilaments with two filtering nonwoven geotextiles that may also be working as separation or protecting layers. the draining three dimensional core will have a “w” configuration as longitudinal parallel channels. minimum thickness to be 7.2mm, with two filtering uv stabilized polypropylene nonwoven geotextile of minimum thickness of 0.75mm charecteristic opening size ( o90 ) of 110 micron and tensile strength of 8.0 kn / m that will be working as separation or protecting layer, geocomposite having in plane flow capacity of 2.1 l / ( m.s ) at hydraulic gradient of 1.0 & 20 kpa pressure and tensile strength of 18 kn / m , with mass per unit area of 740 gsm, supplied in the form of roll for easy transportation to site of work as per detailed specification all complete as per directions of engineer in charge. , supply, installation, testing and commissioning of electrical pane, modular type, front accessible only, free floor standing confirming to minimum ip:43 degree of protection.the panel sheet structure shall undergo seven tank pre treatment process before painting.the sheet steel shall be all of 2.2mm thick crca sheet.all the openable compartments of the panel shall be completely shrouded and provided with padlocking arrangement on all compartments including bus bar and cable alley chambers.the panel height shall not exceed 2200mm and the maximum operating height for any switchgear shall not be more than 1700mm.the panel shall be provided with minimum 75mm base channel frame fabricated from ismc sections.all bus bar links in the panel shall be solid bus bars with coloured pvc shrinkable sleeves, no wires will be acceptable.continuous earth bus shall run alround the panel with earthing studs provided at minimum 2 places.the control wiring shall be carried out with minimum 1.5 / 2.5 sqmm copper wires and adequate number of no / nc, potential free contacts incorporated for remote operation of the starters.proper sized cable termination gland plates shall be provided oncable alleys and knockouts for same shall be provided during fabrication stage itself.the panel shall be provided with a thermostatically controlled heating arrangement ( 200 w ) to take care of high humidity conditions.a 5a socket service outlet ( single phase ) shall be provided in one of the compartments as ervice outlet in the panel.panel shall be so designed at to have minimum 20% spare feeders / space.panel shall undergo epoxy powder coated paint, colour as per is:5 requirement.all cable terminations shall be from top.the complete panel shall be fuse less type, for control circuits 2a / 6a mcbs to be used. all bus bars shall be of aluminium, electrolytic grade only.maximum design density shall not exceed 1 amps / sqmm.all bus bars shall be insulated with coloured heat shrinkable pvc sleeved.all bus bar supports shall be non hygroscopic dmc / smc supports. the panel shall be manufactured in conformance to requirements of local electrical inspector and it shall be contractors responsibility to get initial approval of drawings and also final approval of complete electrical works related to this section. the minimum clearances between bus bars shall be as follows : phase to phase minimum 20mm, phase to neutral minimum 15mm, , sub panel incoming :one ( 1 ) no 200a 4 pole mccb, metering : one ( 1 ) no. ( 0 500v ) 96 x 96 sqmm voltmeter with control fuse & selector switch, one ( 1 ) no. ( 0 200a ) 96 x 96 sqmm ct operated ammeter with selector switch, cts etc., one ( 1 ) set of phase indication lamp., bus bar : one ( 1 ) no.200 a, tpn aluminimum bus bar of suitable length.outgoing :phase indication lamps on each outgoing to be provided., 100amps tpn 2 nos , or outgoing as per site requirment, , incoming :one ( 1 ) no 315a 4 pole mccb, metering :one ( 1 ) no. ( 0 500v ) 96 x 96 sqmm voltmeter with control fuse & selector switch., one ( 1 ) no. ( 0 315a ) 96 x 96 sqmm ct operated ammeter with selector switch, cts etc., one ( 1 ) set of phase indication lamp., bus bar :one ( 1 ) no.315 a, tpn aluminimum bus bar of suitable length., outgoing :phase indication lamps on each outgoing to be provided.100amps tpn 3 nos , or outgoing as per site requirment...

Banaras Hindu University - Uttar Pradesh

32383651 electrical miscellaneous work for bus bar chamber etc ewss, banaras hindu university, varanasi providing & fixing the 440v ac, 3 phase & neutral bus bar chamber etc.as detailed in scope of work & specification of nit(sr. no. 1.0 of page no. 12). 2 bus bar chamber with 100a copper bus bar size of bus bar chamber: 550(l) ×410 (h) × 130(d) mmsize of cu bas bar: 450(l) ×25(w) ×6(t) mm/phase & neutral 3 bus bar chamber with 200a copper bus barsize of bus bar chamber: 640(l) ×550(h) ×150(d) mm size of cu bas bar: 2×540(l)×25(w)×6(t) mm/phase1×540(l)×25(w)×6(t) mm neutral 4 providing and fixing of the following tpn/dp sheet steel clad cfs unit along with suitably rated rewirable fuses of hpl/indo asian make including supply of other installation accessories & consumables required for installation work. 5 16a/240v ac dp sheet steel clad cfs unit. 6 32a/415v ac dp do 7 63a/415v ac dp do 8 63a/415v ac tpn sheet steel clad cfs unit 9 125a/415v ac tpn sheet steel clad cfs unit 10 providing and fixing of the following tpn sheet steel clad switch disconnector fuse (sdf) unit along with suitably rated hrc fuses of l&t make including supply of other installation accessories & consumables required for installation work. 11 32a 415v tpn sdf unit type fn32tpn 12 63a 415v tpn sdf unit type fn63tpn 13 100a 415v tpn sdf unit type fn100tpn 14 125a 415v tpn sdf unit type fn125tpn 15 160a 415v tpn sdf unit type fn160tpn 16 200a 415v tpn sdf unit type fn200tpn 17 250a 415v tpn sdf unit type fn250tpn 18 315a 415v tpn sdf unit type fn315tpn 19 400a 415v tpn sdf unit type fn400tpn 20 630a 415v tpn sdf unit type fn630tpn 21 supply and fixing of the following four pole on load change over switches in sheet steel enclosure with operating handle coupling as per is 8623 and otheriec standardsof l&t make. supply of other installation accessories & consumables required for installation work are also in the contractor’s scope. 22 63a 415v fp on load change over switch 23 125 a 415v fp on load change over switch 24 160 a 415v fp on load change over switch 25 200 a 415v fp on load change over switch 26 250 a 415v fp on load change over switch 27 400 a 415v fp on load change over switch 28 630 a 415v fp on load change over switch 29 providing & fixing of the following items of legrand make. supply of installation accessories & consumables required for the installation work are in contractor’s scope. 30 mcb tpn db 4way cat. no. 507670 31 mcb tpn db 6way cat. no. 507671 32 mcb tpn db 8way cat. no. 507672 33 mcb spn db 8way cat. no. 507611 34 mcb spn db 12way cat. no. 507612 35 mcb spn db 16way cat. no. 507613 36 mcb sp10a – 32a ‘c’ curve 37 mcb dp 40a cat. no. 408637 38 mcb dp 63a cat. no. 408639 39 mcb fp 40a cat. no. 408700 40 mcb fp 63a cat. no. 408702 41 mcb fp 80a cat. no. 808703 42 isolator dp 40a cat. no. 406501 43 isolator dp 63a cat. no. 406502 44 isolator fp 63a cat. no. 406520 45 metal one way dp enclosure cat. no. 507791 46 metal one way tp enclosure cat. no. 507792 47 metal one way fp enclosure cat. no. 507814 48 providing & fixing of the following items of l&t make. supply of installation accessories & consumables required for the installation work are in contractor’s scope. 49 mcb spn db 6way cat no. dbspn006dd 50 mcb spn db 8way cat no. dbspn008dd 51 mcb spn db 12way cat no. dbspn012dd 52 mcb spn db 16way cat no. dbspn016dd 53 mcb tpn db 4way cat no. dbtpe004dd 54 mcb tpn db 6way cat no. dbtpe006dd 55 mcb tpn db 8way cat no. dbtpn008dd 56 mcb sp 6a 32a “c” curve 57 mcb dp 6a 32a “c” curve 58 mcb dp 40a cat no. bb20400c 59 mcb dp 63a cat no. bb20630c 60 mcb tp 40a 63a “c” curve 61 mcb fp 40a 63a “c” curve 62 isolator dp 40a cat no. bf204000 63 isolator dp 63a cat no. bf206300 64 isolator fp 40a cat no. bf404000 65 isolator fp 63a cat no. bf406300 66 isolator fp 80a cat no. bf408000 67 isolator fp 100a cat no. bf410000 68 vertical tpn db with 125a mccb incomer (mccb + outgoing modules) 8way, mccb + 24 modules cat no. dbvtl008dd 69 vertical tpn db with 250a mccb incomer (mccb + outgoing modules) 8way, mccb + 24 modules cat no. dbvth008dd 70 vertical tpn db with 250a mccb incomer (mccb + outgoing modules) 12way, mccb + 36 modules cat no. dbvth012dd 71 analog time switch 3 modules cat no. auts03ana00 72 providing & fixing of the following items of indo asian make. supply of installation accessories & consumables required for the installation work are in contractor’s scope. 73 mcb sp10a – 32a ‘c’ curve hsn code : 8536 74 mcb sp 40a cat. no. 811130 hsn code : 8536 75 mcb sp 63a cat. no. 811132 hsn code : 8536 76 mcb dp 20a cat. no. 811171 hsn code : 8536 77 mcb dp 40a cat. no. 811174 hsn code : 8536 78 mcb dp 63a cat. no. 811176 hsn code : 8536 79 mcb fp 40a cat. no. 811240 hsn code : 8536 80 mcb fp 63a cat. no. 811242 hsn code : 8536 81 dc cb sp 10a cat. no. 811410 hsn code : 8536 82 dc cb sp 16a cat. no. 811412 hsn code : 8536 83 dc cb sp 32a cat. no. 811415 hsn code : 8536 84 dc cb dp 16a cat. no. 811431 hsn code : 8536 85 dc cb dp 32a cat. no. 811434 hsn code : 8536 86 spn db 12way cat. no. 811808 hsn code : 8537 87 tpn db 12way cat. no. 811853 hsn code : 8537 88 tpn db 16way cat. no. 811854 hsn code : 8537 89 vertical tpn db (x250h3 mccb incomer) (mccb + outgoing modules).8way, mccb + 24 modulescat no. 811895 hsn code : 8537 90 vertical tpn db (x250h3 mccb incomer) (mccb + outgoing modules).12way, mccb + 36 modulescat no. 811896 hsn code : 8537 91 analog time switches model name : 3mod din daily cat. no. ta926453 hsn code : 9107 92 250a mccb 4 pole, 415v ac 50hz. 36ka, cat. no. 830112hsn code : 8536 93 250a mccb 3 pole, 415v ac 50hz. 36ka, cat. no. 830336 hsn code : 8536 94 spreaders 4p cat. no. 830619 hsn code : 8538 95 spreaders 4p cat. no. 830633 hsn code : 8538 96 providing & fixing of the following led light fittings of philips make. the supply of installation accessories & consumables required for complete installation/ fixing work are in contractor’s scope. 97 slimline next 20w led batten 98 bn100c led 40w batten 99 recess mounted square led luminaire – 17wmodel rc175 led 15s 100 recess mounted square led luminaire – 39wmodel rc375 led 30s 101 recess mounted round led luminaire – 22w model ultra slim 102 72w led street light luminaire 103 110w led street light luminaire 104 147w led street light luminaire 105 110w led flood light luminaire 106 150w led flood light luminaire 107 200w led flood light luminaire 108 providing & fixing of the following led light fittings of crompton greaves make. the supply of installation accessories & consumables required for installation / fixing work are also in the contractor’s scope. 109 surface mounted type led luminaire 22w – radiance ray. 110 recess mounted type led luminaire – 36w (stellux i/p model) 111 72w led street light luminaire 112 120w led street light luminaire model no. lstp 120 cdl 113 150w led street light luminaire 114 120w led flood light luminaire 115 150w led flood light luminaire 116 200w led flood light luminaire model no. lsfo 200 cdl/60 117 providing & fixing of the following led light fittings of wipro make. the supply of installation accessories & consumables required for installation / fixing work are also in the contractor’s scope. 118 garnet 20w slim led batten 119 garnet plus 36w led batten 120 recessed mounted round slim panel led down lighter – 15w. 121 recess mounted led luminaire with full diffuser – 31w 122 recess mounted square ship led luminaire – 24w 123 70w high performance ip66 led street light 124 110w high performance ip66 led street light 125 150w high performance ip66 led street light 126 120w led flood light luminaire 127 150w led flood light luminaire 128 200w led flood light luminaire 129 recessed/surfaced mounted led luminaries with higher efficacy, full diffuser providing uniform light 36 watt make: wipro cat. no. crco10r038hp57gl1 130 high efficient luminaire with 120 lm/w efficacy helps in power saving & cost saving. 36 watt make: wipro cat. no. crco10r036hp57heg2 131 recess mounted extruded aluminium housing slim luminaire suitable for standalone & continuous techzone ceiling. pmma diffuser for uniform homogeneous light. option in ugr diffuser available 30 watt make: wipro cat no. lm66 531 xxx 57 xx 132 surface mounted downlight with pressure die cast aluminium housing for effective thermal management and high transmission factor pmma diffuser for better performance 9 wattmake: wipro cat no.ld90 111 xxx 30 xx* 133 surface mounted downlight with pressure die cast aluminium housing for effective thermal management and high transmission factor pmma diffuser for better performance 12 wattmake: wipro cat no.ld90 141 xxx 30 xx* 134 surface mounted downlight with pressure die cast aluminium housing for effective thermal management and high transmission factor pmma diffuser for better performance 12 wattmake: wipro cat no.ld90 191 xxx 30 xx** 135 recess mounted, bottom opining cleanroom led luminaire 20 watt make: wipro cat no. lc20 191 xxx 57 gz* 136 ip65 luminaire for surface wall mounted applications 10 watt make: wipro cat no. lwg07 141 xxx 57 g1 137 surface/pendant mounted totally enclosed led luminaire ingress protection: ip65 40 watt make: wipro cat no. le20 491 xxx 57 g1 138 ip65 luminaire with aluminium die cast housing, toughened glass and unique lens system for enhanced illumination 80 watt make: wipro cat no. lf19 931 060 57 xx 139 bollard made of extruded aluminium housing to redefine landscapes with better light quality and enhance architectural design, rated ip65 7 watt make: wipro cat no. lb14 880 xxx 65 05 140 bollard made of extruded aluminium housing to redefine landscapes with better light quality and enhance architectural design, rated ip65 11 watt make: wipro cat no. lb14 131 xxx 65 05 141 providing & fixing of the following electrical items. the supply of installation accessories & consumables required for complete installation / fixing work are also in the contractor’s scope. 142 240v ac 1200mm. sweep ceiling fans with down rod up to 2 feet long. make – crompton greaves, model: high speed. fan color: white/ brown/ ivory. 143 240v ac 1200mm. sweep ceiling fans with down rod more than 2 feet and up to 5 feet long. make – crompton greaves, model: high speed. fan color: white/ brown/ ivory. 144 240v ac 1400mm. sweep ceiling fans with down rod up to 2 feet long. make – crompton greaves, model: high speed. fan color: white/ brown/ ivory. 145 240v ac 1400mm. sweep ceiling fans with down rod more than 2 feet and up to 5 feet long. make – crompton greaves, model: high speed. fan color: white/ brown/ ivory. 146 240v ac 1200mm. sweep ceiling fans with down rod up to 2 feet long. make – usha, model: striker plus (5 star 370 rpm)/technix 5 star fan color: white/brown. 147 240v ac 1200mm. sweep ceiling fans with down rod more than 2 feet and up to 5 feet long. make – usha, model: striker plus (5 star 370 rpm)/technix 5 star fan color: white/brown. 148 240v ac 1400mm. sweep ceiling fans with down rod up to 2 feet long. make – usha, model: striker/sonata fan color: white/brown. 149 240v ac 1400mm. sweep ceiling fans with down rod more than 2 feet and up to 5 feet long. make – usha, model: striker/sonata fan color: white/brown. 150 240v ac, 400 mm dia. wall fan with sweep feature make – crompton/ usha. 151 240v ac 300mm. impeller dia 900/1400 rpm heavy duty industrial exhaust fan complete with bracket louvers & shutter of crompton make. model – exhd 300 4 1/300 6 1. 152 240v ac 450mm. impeller dia 900 rpm heavy duty industrial exhaust fan complete with bracket louvers & shutter of crompton make. model – exhd 450 6 1 153 240v ac 450mm. impeller dia 1400 rpm heavy duty industrial exhaust fan complete with bracket louvers & shutter of crompton make. model – exhd 450 4 1 154 240v ac 300mm.impeller dia 900/1400 rpm heavy duty industrial exhaust fan complete with bracket louvers & shutter of usha make. model : s.ph turbo hdef. 155 240v ac 450mm. impeller dia 900 rpm.heavy duty industrial exhaust fan complete with bracket louvers & shutter of usha make.model : s.ph turbo hdef. 156 240v ac 450mm. impeller dia 1400 rpm.heavy duty industrial exhaust fan complete with bracket louvers & shutter of usha make.model : s.ph turbo hdef. 157 supply & installation including laying & dressing of the following lt power cables on ready cable trenches/in air/concrete wall etc. as detailed in scope of work & specification of nit(sr. no. 12.0 of page no. 15). 158 1.1kv grade 3 ½ core × 120 sqmm. pvc/xlpe cables. 159 1.1kv grade 3 ½ core × 95 sqmm.do 160 1.1kv grade 3 ½ core × 70 sqmm.do 161 1.1kv grade 3 ½ core × 50 sqmm.do 162 1.1kv grade 3 ½ core ×35 sqmm. do 163 1.1kv grade 3 ½ core ×25 sqmm. do 164 1.1kv grade 4 core × 16 sqmm.do 165 1.1kv grade 4 core × 10 sqmm.do 166 1.1kv grade 4 core × 6 sqmm. do 167 1.1kv grade 2 core × 6 sqmm. do 168 excavation of earth cable trench minimum 900mm deep and 450mm wide and supply & installation including underground laying/dressing of the following lt power cables etc. as detailed in scope of work & specification of nit(sr. no. 13.0 of page no. 16). 169 1.1kv grade 3 ½ core × 120 sqmm. pvc/xlpe cables. 170 1.1kv grade 3 ½ core × 95 sqmm. do 171 1.1kv grade 3 ½ core × 70 sqmm.do 172 1.1kv grade 3 ½ core × 50 sqmm. do 173 1.1kv grade 3 ½ core ×35 sqmm.do 174 1.1kv grade 3 ½ core ×25 sqmm.do 175 1.1kv grade 4 core × 16 sqmm. do 176 1.1kv grade 4 core × 10 sqmm. do 177 1.1kv grade 4 core × 6 sqmm.do 178 1.1kv grade 2 core × 6 sqmm.do 179 installation/ fixing of the following electrical items etc. as detailed in scope of work & specification of nit(sr. no. 14.0 of page no. 16 to 17). 180 630/400a tpn sheet steel clad cfs unit 181 300/250/200a tpndo 182 160/125/100a tpndo 183 63/32a tpn do 184 63a dp sheet steel clad cfs 185 32a/16a dp sheet steel clad cfs 186 mcb distribution board 230v ac spn 4/8/10 way 10a 32a 187 do 12/14/16 way 10a 32a 188 do4/8/10 way 40a 63a 189 do 12/14/16 way 40a 63a 190 mcb distribution board 440v ac tpn 4/6/8 way 10a 32a 191 do10/12/16 way 10a 32a 192 do4/6/8 way 40a 63a 193 do10/12/16 way 40a 63a 194 led 20/40w tube light fittings 195 led recess type fittings 2’x2’ 196 led recess type fittings 1’x1’ 197 led recess type fittings round 1’ dia. 198 led 70/80/90/110w street light fittings 199 led 150w/200w street light fittings 200 led 110w/150w flood light fittings 201 led 150/200w flood light fittings 202 fan regulator – electronic type 203 48”/56” sweep ceiling fans with down rod approx 2” long. 204 48”/56” sweep ceiling fans with down rod more than 2” long. 205 230v ac 9”/12” impeller dia 950/1450 rpm. heavy duty industrial exhaust fan complete with brackets, louver, shutter etc. 206 do 14”/18” impeller dia 950/1450 rpm. do 207 do 20”/24” impeller dia 700/950 rpm. do 208 erection of l.t. feeder pillar of approx dimension 1000 (l) x 1250/1450 (h) x 700 (d) mm etc. as detailed in scope of work & specification of nit(sr. no. 15.0 of page no. 17). 209 providing and fixing of the following tpn sheet steel clad switch disconnector fuse (sdf) unit along with suitably rated hrc fuses of c&s make including supply of other installation accessories & consumables required for installation work. 210 32a 415v tpn sdf unit type e cssdf32d3n 211 63a 415v tpn sdf unit type e cssdf63d3n 212 100a 415v tpn sdf unit type e cssdf100d3n 213 125a 415v tpn sdf unit type e cssdf125d3n 214 160a 415v tpn sdf unit type e cssdf160d3n 215 200a 415v tpn sdf unit type e cssdf200d3n 216 250a 415v tpn sdf unit type e cssdf250d3n 217 315a 415v tpn sdf unit type e cssdf315d3n 218 400a 415v tpn sdf unit type e cssdf400d3n 219 630a 415v tpn sdf unit type e cssdf630d3n 220 supply and fixing of the following four pole on load change over switches in sheet steel enclosure with operating handle coupling as per is 8623 and otheriec standardsof c&s make. supply of other installation accessories & consumables required for installation work are also in the contractor’s scope. 221 63a 415v fp on load change over switch 222 100a 415v fp on load change over switch 223 125 a 415v fp on load change over switch 224 160 a 415v fp on load change over switch 225 200 a 415v fp on load change over switch 226 250 a 415v fp on load change over switch 227 315 a 415v fp on load change over switch 228 400 a 415v fp on load change over switch 229 630 a 415v fp on load change over switch 230 providing & fixing of the following items of c&s make. supply of installation accessories & consumables required for the installation work are in contractor’s scope. 231 mcb tpn db 4way cat. no. csdbtpnhdd04 232 mcb tpn db 6way cat. no. csdbtpnhdd06 233 mcb tpn db 8way cat. no. csdbtpnhdd08 234 mcb spn db 4way cat. no. csdbspndd04 235 mcb spn db 8way cat. no. csdbspndd08 236 mcb spn db 12way cat. no. csdbspndd012 237 mcb spn db 16way cat. no. csdbspndd016 238 mcb sp6a – 32a ‘c’ curve 239 mcb sp40a ‘c’ curve cat. no. csmbs1c40 240 mcb sp63a ‘c’ curve csmbs1c63 241 mcb dp 25a cat. no. csmbs2c25 242 mcb dp 40a cat. no. csmbs2c40 243 mcb dp 63a cat. no. csmbs2c63 244 mcb fp 40a cat. no. csmbs4c40 245 mcb fp 63a cat. no. csmbs4c63 246 isolator dp 40a cat. no. csmbs2iso40 247 isolator dp 63a cat. no. csmbs2iso63 248 isolator fp 63a cat. no. csmbs4iso63 249 isolator fp 80a cat. no. csmbs4iso80 250 isolator fp 100a cat. no. csmbs4iso100 251 metal one way dp enclosure cat. no. csbdmcbedp 252 metal one way fp enclosure cat. no. csbdmcbefp => limited...

Banaras Hindu University - Uttar Pradesh

32332817 electrical miscellaneous work for bus bar chamber ewss, banaras hindu university, varanasi providing & fixing the 440v ac, 3 phase & neutral bus bar chamber etc.as detailed in scope of work & specification of nit ( sr. no. 1.0 of page no. 12 ) . 2 bus bar chamber with 100a copper bus bar size of bus bar chamber: 550 ( l ) ×410 ( h ) × 130 ( d ) mmsize of cu bas bar: 450 ( l ) ×25 ( w ) ×6 ( t ) mm / phase & neutral 3 bus bar chamber with 200a copper bus barsize of bus bar chamber: 640 ( l ) ×550 ( h ) ×150 ( d ) mm size of cu bas bar: 2×540 ( l ) ×25 ( w ) ×6 ( t ) mm / phase1×540 ( l ) ×25 ( w ) ×6 ( t ) mm neutral 4 providing and fixing of the following tpn / dp sheet steel clad cfs unit along with suitably rated rewirable fuses of hpl / indo asian make including supply of other installation accessories & consumables required for installation work. 5 16a / 240v ac dp sheet steel clad cfs unit. 6 32a / 415v ac dp do 7 63a / 415v ac dp do 8 63a / 415v ac tpn sheet steel clad cfs unit 9 125a / 415v ac tpn sheet steel clad cfs unit 10 providing and fixing of the following tpn sheet steel clad switch disconnector fuse ( sdf ) unit along with suitably rated hrc fuses of l&t make including supply of other installation accessories & consumables required for installation work. 11 32a 415v tpn sdf unit type fn32tpn 12 63a 415v tpn sdf unit type fn63tpn 13 100a 415v tpn sdf unit type fn100tpn 14 125a 415v tpn sdf unit type fn125tpn 15 160a 415v tpn sdf unit type fn160tpn 16 200a 415v tpn sdf unit type fn200tpn 17 250a 415v tpn sdf unit type fn250tpn 18 315a 415v tpn sdf unit type fn315tpn 19 400a 415v tpn sdf unit type fn400tpn 20 630a 415v tpn sdf unit type fn630tpn 21 supply and fixing of the following four pole on load change over switches in sheet steel enclosure with operating handle coupling as per is 8623 and otheriec standardsof l&t make. supply of other installation accessories & consumables required for installation work are also in the contractor’s scope. 22 63a 415v fp on load change over switch 23 125 a 415v fp on load change over switch 24 160 a 415v fp on load change over switch 25 200 a 415v fp on load change over switch 26 250 a 415v fp on load change over switch 27 400 a 415v fp on load change over switch 28 630 a 415v fp on load change over switch 29 providing & fixing of the following items of legrand make. supply of installation accessories & consumables required for the installation work are in contractor’s scope. 30 mcb tpn db 4way cat. no. 507670 31 mcb tpn db 6way cat. no. 507671 32 mcb tpn db 8way cat. no. 507672 33 mcb spn db 8way cat. no. 507611 34 mcb spn db 12way cat. no. 507612 35 mcb spn db 16way cat. no. 507613 36 mcb sp10a – 32a ‘c’ curve 37 mcb dp 40a cat. no. 408637 38 mcb dp 63a cat. no. 408639 39 mcb fp 40a cat. no. 408700 40 mcb fp 63a cat. no. 408702 41 mcb fp 80a cat. no. 808703 42 isolator dp 40a cat. no. 406501 43 isolator dp 63a cat. no. 406502 44 isolator fp 63a cat. no. 406520 45 metal one way dp enclosure cat. no. 507791 46 metal one way tp enclosure cat. no. 507792 47 metal one way fp enclosure cat. no. 507814 48 providing & fixing of the following items of l&t make. supply of installation accessories & consumables required for the installation work are in contractor’s scope. 49 mcb spn db 6way cat no. dbspn006dd 50 mcb spn db 8way cat no. dbspn008dd 51 mcb spn db 12way cat no. dbspn012dd 52 mcb spn db 16way cat no. dbspn016dd 53 mcb tpn db 4way cat no. dbtpe004dd 54 mcb tpn db 6way cat no. dbtpe006dd 55 mcb tpn db 8way cat no. dbtpn008dd 56 mcb sp 6a 32a “c” curve 57 mcb dp 6a 32a “c” curve 58 mcb dp 40a cat no. bb20400c 59 mcb dp 63a cat no. bb20630c 60 mcb tp 40a 63a “c” curve 61 mcb fp 40a 63a “c” curve 62 isolator dp 40a cat no. bf204000 63 isolator dp 63a cat no. bf206300 64 isolator fp 40a cat no. bf404000 65 isolator fp 63a cat no. bf406300 66 isolator fp 80a cat no. bf408000 67 isolator fp 100a cat no. bf410000 68 vertical tpn db with 125a mccb incomer ( mccb + outgoing modules ) 8way, mccb + 24 modules cat no. dbvtl008dd 69 vertical tpn db with 250a mccb incomer ( mccb + outgoing modules ) 8way, mccb + 24 modules cat no. dbvth008dd 70 vertical tpn db with 250a mccb incomer ( mccb + outgoing modules ) 12way, mccb + 36 modules cat no. dbvth012dd 71 analog time switch 3 modules cat no. auts03ana00 72 providing & fixing of the following items of indo asian make. supply of installation accessories & consumables required for the installation work are in contractor’s scope. 73 mcb sp10a – 32a ‘c’ curve hsn code : 8536 74 mcb sp 40a cat. no. 811130 hsn code : 8536 75 mcb sp 63a cat. no. 811132 hsn code : 8536 76 mcb dp 20a cat. no. 811171 hsn code : 8536 77 mcb dp 40a cat. no. 811174 hsn code : 8536 78 mcb dp 63a cat. no. 811176 hsn code : 8536 79 mcb fp 40a cat. no. 811240 hsn code : 8536 80 mcb fp 63a cat. no. 811242 hsn code : 8536 81 dc cb sp 10a cat. no. 811410 hsn code : 8536 82 dc cb sp 16a cat. no. 811412 hsn code : 8536 83 dc cb sp 32a cat. no. 811415 hsn code : 8536 84 dc cb dp 16a cat. no. 811431 hsn code : 8536 85 dc cb dp 32a cat. no. 811434 hsn code : 8536 86 spn db 12way cat. no. 811808 hsn code : 8537 87 tpn db 12way cat. no. 811853 hsn code : 8537 88 tpn db 16way cat. no. 811854 hsn code : 8537 89 vertical tpn db ( x250h3 mccb incomer ) ( mccb + outgoing modules ) .8way, mccb + 24 modulescat no. 811895 hsn code : 8537 90 vertical tpn db ( x250h3 mccb incomer ) ( mccb + outgoing modules ) .12way, mccb + 36 modulescat no. 811896 hsn code : 8537 91 analog time switches model name : 3mod din daily cat. no. ta926453 hsn code : 9107 92 250a mccb 4 pole, 415v ac 50hz. 36ka, cat. no. 830112hsn code : 8536 93 250a mccb 3 pole, 415v ac 50hz. 36ka, cat. no. 830336 hsn code : 8536 94 spreaders 4p cat. no. 830619 hsn code : 8538 95 spreaders 4p cat. no. 830633 hsn code : 8538 96 providing & fixing of the following led light fittings of philips make. the supply of installation accessories & consumables required for complete installation / fixing work are in contractor’s scope. 97 slimline next 20w led batten 98 bn100c led 40w batten 99 recess mounted square led luminaire – 17wmodel rc175 led 15s 100 recess mounted square led luminaire – 39wmodel rc375 led 30s 101 recess mounted round led luminaire – 22w model ultra slim 102 72w led street light luminaire 103 110w led street light luminaire 104 147w led street light luminaire 105 110w led flood light luminaire 106 150w led flood light luminaire 107 200w led flood light luminaire 108 providing & fixing of the following led light fittings of crompton greaves make. the supply of installation accessories & consumables required for installation / fixing work are also in the contractor’s scope. 109 surface mounted type led luminaire 22w – radiance ray. 110 recess mounted type led luminaire – 36w ( stellux i / p model ) 111 72w led street light luminaire 112 120w led street light luminaire model no. lstp 120 cdl 113 150w led street light luminaire 114 120w led flood light luminaire 115 150w led flood light luminaire 116 200w led flood light luminaire model no. lsfo 200 cdl / 60 117 providing & fixing of the following led light fittings of wipro make. the supply of installation accessories & consumables required for installation / fixing work are also in the contractor’s scope. 118 garnet 20w slim led batten 119 garnet plus 36w led batten 120 recessed mounted round slim panel led down lighter – 15w. 121 recess mounted led luminaire with full diffuser – 31w 122 recess mounted square ship led luminaire – 24w 123 70w high performance ip66 led street light 124 110w high performance ip66 led street light 125 150w high performance ip66 led street light 126 120w led flood light luminaire 127 150w led flood light luminaire 128 200w led flood light luminaire 129 630 / 400a tpn sheet steel clad cfs unit 130 300 / 250 / 200a tpndo 131 160 / 125 / 100a tpndo 132 63 / 32a tpn do 133 63a dp sheet steel clad cfs 134 32a / 16a dp sheet steel clad cfs 135 mcb distribution board 230v ac spn 4 / 8 / 10 way 10a 32a 136 do 12 / 14 / 16 way 10a 32a 137 do4 / 8 / 10 way 40a 63a 138 do 12 / 14 / 16 way 40a 63a 139 mcb distribution board 440v ac tpn 4 / 6 / 8 way 10a 32a 140 do10 / 12 / 16 way 10a 32a 141 providing & fixing of the following electrical items. the supply of installation accessories & consumables required for complete installation / fixing work are also in the contractor’s scope. 142 240v ac 1200mm. sweep ceiling fans with down rod up to 2 feet long. make – crompton greaves, model: high speed. fan color: white / brown / ivory. 143 240v ac 1200mm. sweep ceiling fans with down rod more than 2 feet and up to 5 feet long. make – crompton greaves, model: high speed. fan color: white / brown / ivory. 144 240v ac 1400mm. sweep ceiling fans with down rod up to 2 feet long. make – crompton greaves, model: high speed. fan color: white / brown / ivory. 145 240v ac 1400mm. sweep ceiling fans with down rod more than 2 feet and up to 5 feet long. make – crompton greaves, model: high speed. fan color: white / brown / ivory. 146 240v ac 1200mm. sweep ceiling fans with down rod up to 2 feet long. make – usha, model: striker plus ( 5 star 370 rpm ) / technix 5 star fan color: white / brown. 147 240v ac 1200mm. sweep ceiling fans with down rod more than 2 feet and up to 5 feet long. make – usha, model: striker plus ( 5 star 370 rpm ) / technix 5 star fan color: white / brown. 148 240v ac 1400mm. sweep ceiling fans with down rod up to 2 feet long. make – usha, model: striker / sonata fan color: white / brown. 149 240v ac 1400mm. sweep ceiling fans with down rod more than 2 feet and up to 5 feet long. make – usha, model: striker / sonata fan color: white / brown. 150 240v ac, 400 mm dia. wall fan with sweep feature make – crompton / usha. 151 240v ac 300mm. impeller dia 900 / 1400 rpm heavy duty industrial exhaust fan complete with bracket louvers & shutter of crompton make. model – exhd 300 4 1 / 300 6 1. 152 240v ac 450mm. impeller dia 900 rpm heavy duty industrial exhaust fan complete with bracket louvers & shutter of crompton make. model – exhd 450 6 1 153 240v ac 450mm. impeller dia 1400 rpm heavy duty industrial exhaust fan complete with bracket louvers & shutter of crompton make. model – exhd 450 4 1 154 240v ac 300mm.impeller dia 900 / 1400 rpm heavy duty industrial exhaust fan complete with bracket louvers & shutter of usha make. model : s.ph turbo hdef. 155 240v ac 450mm. impeller dia 900 rpm.heavy duty industrial exhaust fan complete with bracket louvers & shutter of usha make.model : s.ph turbo hdef. 156 240v ac 450mm. impeller dia 1400 rpm.heavy duty industrial exhaust fan complete with bracket louvers & shutter of usha make.model : s.ph turbo hdef. 157 supply & installation including laying & dressing of the following lt power cables on ready cable trenches / in air / concrete wall etc. as detailed in scope of work & specification of nit ( sr. no. 12.0 of page no. 15 ) . 158 1.1kv grade 3 ½ core × 120 sqmm. pvc / xlpe cables. 159 1.1kv grade 3 ½ core × 95 sqmm.do 160 1.1kv grade 3 ½ core × 70 sqmm.do 161 1.1kv grade 3 ½ core × 50 sqmm.do 162 1.1kv grade 3 ½ core ×35 sqmm. do 163 1.1kv grade 3 ½ core ×25 sqmm. do 164 1.1kv grade 4 core × 16 sqmm.do 165 1.1kv grade 4 core × 10 sqmm.do 166 1.1kv grade 4 core × 6 sqmm. do 167 1.1kv grade 2 core × 6 sqmm. do 168 excavation of earth cable trench minimum 900mm deep and 450mm wide and supply & installation including underground laying / dressing of the following lt power cables etc. as detailed in scope of work & specification of nit ( sr. no. 13.0 of page no. 16 ) . 169 1.1kv grade 3 ½ core × 120 sqmm. pvc / xlpe cables. 170 1.1kv grade 3 ½ core × 95 sqmm. do 171 1.1kv grade 3 ½ core × 70 sqmm.do 172 1.1kv grade 3 ½ core × 50 sqmm. do 173 1.1kv grade 3 ½ core ×35 sqmm.do 174 1.1kv grade 3 ½ core ×25 sqmm.do 175 1.1kv grade 4 core × 16 sqmm. do 176 1.1kv grade 4 core × 10 sqmm. do 177 1.1kv grade 4 core × 6 sqmm.do 178 1.1kv grade 2 core × 6 sqmm.do 179 installation / fixing of the following electrical items etc. as detailed in scope of work & specification of nit ( sr. no. 14.0 of page no. 16 to 17 ) . 180 630 / 400a tpn sheet steel clad cfs unit 181 300 / 250 / 200a tpndo 182 160 / 125 / 100a tpndo 183 63 / 32a tpn do 184 63a dp sheet steel clad cfs 185 32a / 16a dp sheet steel clad cfs 186 mcb distribution board 230v ac spn 4 / 8 / 10 way 10a 32a 187 do 12 / 14 / 16 way 10a 32a 188 do4 / 8 / 10 way 40a 63a 189 do 12 / 14 / 16 way 40a 63a 190 mcb distribution board 440v ac tpn 4 / 6 / 8 way 10a 32a 191 do10 / 12 / 16 way 10a 32a 192 do4 / 6 / 8 way 40a 63a 193 do10 / 12 / 16 way 40a 63a 194 led 20 / 40w tube light fittings 195 led recess type fittings 2’x2’ 196 led recess type fittings 1’x1’ 197 led recess type fittings round 1’ dia. 198 led 70 / 80 / 90 / 110w street light fittings 199 led 150w / 200w street light fittings 200 led 110w / 150w flood light fittings 201 led 150 / 200w flood light fittings 202 fan regulator – electronic type 203 48” / 56” sweep ceiling fans with down rod approx 2” long. 204 48” / 56” sweep ceiling fans with down rod more than 2” long. 205 230v ac 9” / 12” impeller dia 950 / 1450 rpm. heavy duty industrial exhaust fan complete with brackets, louver, shutter etc. 206 do 14” / 18” impeller dia 950 / 1450 rpm. do 207 do 20” / 24” impeller dia 700 / 950 rpm. do 208 erection of l.t. feeder pillar of approx dimension 1000 ( l ) x 1250 / 1450 ( h ) x 700 ( d ) mm etc. as detailed in scope of work & specification of nit ( sr. no. 15.0 of page no. 17 ) . => limited...

Uttar Pradesh Housing And Development Board - Uttar Pradesh

32092032 electrical / mechanical work at 100 bedded hospital gramsabha shivshat raniganj distt. pratapgarh 1 internal electrification workwiring point for light with 1.5 sq. mm.frlsh pvc insulated multistrand single core copper conductor cable in pvc conduit partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 1.5 sqmm frlsh pvc insulated multistrand copper conductor cable as earth wire drawn inside the conduit with gp box, modular type switch & ceiling rose / angle / batten holder on 3mm thick phenolic paminated backalite sheet etc complete in all respect as directed including matching colour wash. pwd sor 2018 si no 138 ( c ) +187 ( a ) 2 wiring point for two way light with 1.5 sq. mm. frls pvc insulated multistrand single core copper conductor cable in heavy guage pvc conduit. pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting complete with 1.5 sq. mm. frlsh pvc insulated multistrand copperconductor cable as earthwire drawn inside the conduit, gp box and 2no. two way modular type switches and ceiling rose / angle / batten holder on 3 mm. thick phenolic laminated backlite sheet etc. complete in all respects, as directed including matching colour wash.pwd sor 2018 si no 139 ( c ) + 187 ( b ) 3 wiring point for fan / fresh air fan ( light duty exhaust fan ) with 1.5 sq.mm.frlsh pvc insulated multistrand single core copper conductor cable in pvc conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 1.5 sq.mm.frlsh pvc insulated multistrand copper conductor cable as earth wiredrawn inside the conduit withmodular type switch & ceiling rose on 3 mm. thick backelite sheet etc., complete in all respect including matching colour wash. pwd sor 2018 sl no 140 ( c ) + 187 ( a ) 4 wiring point for call bell with 1.5 sq. mm. frls pvc insulated multistrand single core copper conductor cable in heavy guage pvc conduit. pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting complete with 1.5 frlsh pvc insulated multistrand copperconductor cable as earthwire drawn inside the conduit, gp box and modular type bell push or 2 pin shocket etc complete in all respects, as directed including matching colour wash. pwd sor 2018 si no 142 ( c ) + 187 ( e ) 5 wiring point for plug with 1.5 sq. mm.frlsh pvc insulated multistrand copper onductor cable in pvc conduitpartly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 1.5 sq.mm.frlsh pvc insulated multistrand copper conductor cable as earth wiredrawn inside the conduit and modular type switch and socket etc., complete in all respect including matching colour wash.pwd sor 2018 sl no 141 ( c ) + 187 ( a ) 6 supply and wiring of submain with two number 2.5 sq.mm. frlsh pvc insulated 1100 v grade multistrand single core copper conductor cable in 20 mm dia heavy duty ( 2mm thick ) pvc conduit partly laid in slab alongwith the reinforcement before concreting and partly concealed in wall with 1 nos. 1.5 sq. mm. frlsh pvc insulated 1100 v grade multistrand single core copper conductor cable as earth continuity wire drawn inside the conduit complete in all respect. including matching colour wash. pwd sor 2018 sl no 1307 ( c ) 7 supply and wiring of submain with two number 4 sq.mm. frlsh pvc insulated 1100 v grade multistrand single core copper conductor cable in 20 mm dia heavy duty ( 2 mm thick ) pvc conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting with one no. 2.5 sq. mm. frlsh pvc insulated multistrand copper conductor cable as earth continuity wire drawn in conduit including matching colour wash etc. complete in all respect. pwd sor 2018 sl no 221 ( c ) 8 supply and wiring of sub main with two number 6.0 sq.mm frlsh pvc insulated 1100 v grade multstrand single core copper conductor cable in 20 mm dia heavy duty ( 2mm thick ) pvc conduit partly concealed in wall and partly laid in slab along with reinforcement before concretiing with 1 no. 4.0 sq.mm. frlsh pvc insulated multstrand copper conductor cable as earth continuity wire drawn iin conduit including matching colour wash. complete in all respect pwd sor 2018 si no 222 ( c ) 9 supply and wiring of 4 number 6 sq. mm. frlsh pvc insulated 1100 v grade multistrand single core copper conductor cable in 32 mm dia heavy duty ( 2mm thick ) pvc conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting with 2 nos 4 sq.mm. frlsh pvc insulated copper conductor cable as earth continuity wire drawn in conduitincluding matching colour wash etc. complete in all respect..pwd sor 2018 sl no 278 ( c ) 10 supply and wiring of 4 number 10 sq. mm. frlsh pvc insulated 1100 v grade multistrand single core copper conductor cable in 32 mm dia heavy duty ( 2mm thick ) pvc conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting with 2 nos 6 sq.mm. frlsh pvc insulated copper conductor cable as earth continuity wire drawn in conduitincluding matching colour wash etc. complete in all respect..pwd sor 2018 sl no 278 ( c ) 11 supply and wiring of sub main with 4 number 16.0 sq.mm frlshpvc insulated 1100 v grade multstrand single core copper conductor cable in 40mm dia pvc conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting with two number 10 sq.mm. rlsh pvc insulated copper conductor cable as earth continuity wire drawn in conduitincluding matching colour wash etc. complete in all respect. pwd sor 2018 si no 279 ( c ) 12 supply and fixing hexagonal / round g.p. fan box of approved make made up of 1.0 mm thick isi marked g.p. sheet spot welded four to eight holes of 25.4 mm for pipe entry of the box. holes should be semi shuttered type with 0.5 mm g.p. sheet made upper & lower cover duly screwed fitted with 300 mm round zink coated m.s bar x 12 mm & brand name should be embossed. fixing with wiring conduit laid in the r.c.c. roof before concreting along with supply of all material, labor, t&p etc. required for proper completion of the work .pwd sor 2018 s.i.no. 1149 13 supply and fixing of led tube light with metal heavy duty box type batten light fitting 1 x 22 watt suitable for upto 1x22 watt led polycarbonate tube light complete including tube suitabe for both surface & suspended complete in all respect. 2420 system lumens, 110lm / watt pf>0.95, thd<10% cri>80, sheet thicknes 0.8mm, tube with aluminium heat with 5 year warrantee. pwd sor 2018 sl no 1434 cat aaa 14 supply and fixing of recess / surface mounting round 18 watt to 20 watt cut out min 150 mm height min 40 mm, led down lighter having powder coated die cast aluminium housing with heat sink diffuser / reflector and driver set suitable for 24 hr continuous operation, compelete in all respect. pwd sor 1980 2200 system lumens, 110lm / watt pf>0.95, thd<10% at full load, cri>80, with 5 year warrantee. si no. 1403 15 supply and fixing of water tight oblong 10 watt led bulkhead luminaire with driver set confirming to ip 65 and above protection . complete in all respect. si no. 1417 cat aaa 16 supply and fixing of 36 watt to 46 watt indoor recess mounting led square fitting for armstrong ceiling having powder coated die cast aluminium housing body with extended heat sink and diffuser of special polycarbonate meterial and driver set complete in all respect.pwd sor 2018 s.i.no. 1406 cat a 17 making hole in the wall for exhaust fan and finishingproperly complete in allrespect.pwd sor 2018 s.i.no. 1121 18 supply and erection of 300 mm sweep ac 230 / 250 volts, 50 hz exhast fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required connection etc. complete as required mr 19 supply and erection of 400 mm sweep ac 230 / 250 volts, 50 hz wall fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required connection etc. complete as requiredmr 20 supply and fixing of electronic fan regulator ( modular ) 120 280 v. isi marked, on the existing switch board including making connections, required material, labour t&p etc. for proper completion of work to the satisfaction of engineer in charge of work. pwd sor 2018 s.i.no. 1203 ( c ) 21 supply and erection of ceiling fan with motor of ac permanent insulation, capacitor rating conforming bee 5 star rating and is:374 / 79 and also comply with is: 1709 / 1984 with latest amendment. the rated voltage 220 / 240 volts, 50hz 1 ph ac the fan assemble should consists of down rod, blades, shackle, canopies etc and with double ball bearing system .pwd sor 2018 si no 1501+ 1115 bee 5 star rated 1200 mm sweep 22 s / f of 3mm thick bakelite sheet cover round / hexagonal type for fan box complete with all material, labour t&p as per direction of e / i. 23 s / f of 3mm thickal. sheet junction box cover complete in all material labour t&p as per direction of e / i. 24 supply and fixing of surface / flush mounting 8 way tpn distribution board with additional metal door without mcb complete in all respect and directed at site by e / i. pwd sor 2018 si no 1027 ( a ) cat a 25 s&f of 6 amp to 32 amp. spmcb ( 10 ka ) c curve pwd sor 2018 si no 1002 cat a 26 s&f of 63 amp. 4 polespmcb ( 10 ka ) c curve pwd sor 2018 si no 1007 27 supply and fixing of power plug with 20 amp. / 250 voltflush type modular switch and 5 pin 20 a / 250 volt flush type universal modular socketswitch on concealed m.s boxincluding supply of all material, labour t&p etc. required for proper completion of work. pwd sor 2018 si no 1139 ( a ) 28 s & f sheet steel enclosure surface / flush mounting fitted with 30amp. 2pin and earth metal clad scraping earth plug and socket complete in all respect. as directed at site byengineer in charge.1031 ( a ) 29 supply and burring of safe earthing electrode t 39 zn zinc coated, length 3000mm, outer pipe 76.3mm x 3.2 inner pipe 42.4mm x 2.6mm, terminal dia 12mm, coating 80 100 micron filled with crystalline conductive mixture ( ccm ) having anti corrosive & conductive property with 50 kgs activated soil ( bfc ) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square c.i. frame with hinged cover & masonry housing. ( from electrode terminal to switch board, cost of 25 x 3 g.i. strip will be extra make: as approved in u.p. p.w.d., & c.p.r.i. certified pwd sor 2018 si no 726 ( d ) 30 supply and laying of 25 mm x 3 mm g.i srtip form earth electrode directly in the ground as required complete in all respects. pwd sor 2018 si no 716 31 providing, laying and fixing 100mm dia g.i. pipe ( medium class ) in ground complete with g.i. fittings including trenching ( 75 cm deep ) and re filling etc as required. dsr 2018 si no 14.13.3 32 supplyandlayingof aluminiumconductorpvcinsulated armoured served sheathed cables 1100 volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. on surface the cable run shall be fixed on m.s. clamps etc. of suitable size or as directed by the engineer incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. pwd sor 2018 si no 501 33 10 sq mm 4 core 34 16 sq mm 4 core 35 70 sq mm 3.5 core 36 95 sq mm 3.5 core 37 240 sq mm 3.5 core 38 300 sq mm3.5 core 39 supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. the armouring ofthe cable shall be properly connected with the earth as per direction of engineer incharge.pwd sor 2018 si no 503 40 10 sq mm 4 core 41 16 sq mm 4 core 42 70 sq mm 3.5 core 43 95 sq mm 3.5 core 44 240 sq mm 3.5 core 45 300 sq mm3.5 core 46 supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respects as per direction of the engineer incharge.pwd sor 2018 si no 504 47 10 sq mm 48 16 sq mm 49 35 sq mm 50 50 sq mm 51 70 sq mm 52 95 sq mm 53 120 sq mm 54 240 sq mm 55 300 sq mm 56 supply and fixing of call bell of approved make on polished mdfeg / teak ply board including making connections etc. complete in all respect. pwd sor 2018 si no 1101 57 supply of franklin france make advanced piezoelectric exciter device based lighting protection system suitable for protection of building against direct lightning strike complete with ealy streamer emission with piwezoelectric device for corona effect ) stainlles steel lighting conductor air terminal with event counter with sensitivity 1 ka to 100 ka for 8.20 micro second impulse for 1 ka control over the release of ions positive or negative without additional power supplies requirement required complianece with ip53 enclosures ) 58 saint elmo lightening conductor with discharge counter ( sensitivity 1 ka, 8 / 20 microsecound with ip 53 enclosures ) 59 elevation rod : 2m. afc2001 two elevation rods for are required for mounting a one lightening conductor mr 60 installation of franklin france make external lightening protection system. 61 ssupply and fixing of vertical down conductor of 32mm x 6mm g.i. strip etc. on approved clamps on surface for lightning conductor complete in all respects ( for two storeyed buildings ) .p.w.d.s.o.r. 2018 s.i. no.713 ( c ) 62 supply and fixing of testing joint of g.i. strip 32mm x 6mm and 150mm long with g.i. bolts and nut etc. complete in all respect.p.w.d.s.o.r. 2018 s.i. no.719 63 supplying and fixing following modular switch / socket on theexisting modular plate & switch box including connections but excluding modular plate etc as required. telephone socket outlet dsr no 1.24.6 64 supply and fixing of g.p. modular switch box for 1 / 2 module of approved make made up of 1.0 mm thick isi marked g.p.sheet including adjestable nakka and holes plugged with pvc nylon caps . two or more holes for pipe entry of 25.4 mm on upper and lower sides of the box. holes should be semi shuttered type and fitted with heavy brass earth piller duly screwed & brand name should be embossed. box flushed in wall including cutting of brick work, fixing it to the level with cement sand mortar, including matching colour wash with s / o all materials, labour and t&p required for proper completion of work as directed at site by the engineer in charge. p.w.d.s.o.r. 2018 s.i. no.1152 ( a ) 65 1 or 2 module ( 75mm x 75 mm ) 66 supplying and drawing telephone wire following pair 0.5 sqmm fr pvc insulated annealed copper conductor, unarmoured telephone cable in the existing surface / recessed steel / pvc conduit as required. dsr no 1.18.2 67 2 pair 68 supply and fixing and concealing of 20 mm dia. 2mm thick pvc conduit pipe with isi mark embossed and with pvc accessories confirming to is no. 3419 for drawing wires duly sealed at joints with original resin / adhesive to make the complete piping rigid, plastering with cement sand mortar finished to the level with matching colour wash including cost of all material labour and t&p etc required for proper completion of the work as per directions and to the satisfaction of engineer in charge. sor 2018 si no. 148 ( a ) 69 supply and laying of 1800mm x 900mm x 12mm thick chequered rubbbber matting of tested quality sor 2018 si no. 1136 70 s & f sheet steel enclosure for t.p. / four pole mcb. sor 2018 si no. 1033 71 s&f of 63 amp. 4 pole mcb ( 10 ka ) c curve sor 2018 si no. 1020 ( a ) cat aaa 72 fire fighting systemproviding, laying, testing & commissioning of c class heavy duty ms pipe conforming to is 3589 / is 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall / ceiling with suitable clamp / support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : dsr & aor 2019 si no 7 73 200 mm dia 74 150 mm dia 75 100 mm dia 76 80 mm dia 77 65mm dia 78 50mm dia 79 40mm dia 80 32mm dia 81 25 mm dia 82 providing laying, testing & commissioning of c class heavy duty ms pipe conforming to is 1239 / 3589 i / c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar / asphalt tape as per is 10221, refilling the trench etc. of following sizes complete as required. dsr & aor 2019 83 200 mm dia si no 6.1 84 150 mm dia si no 6.2 85 supplying, fixing, testing and commissioning of manual swing typehose reel is:444 complete with heavy duty reel, 20 mm dia. x 30 mtr long, pvc pressure hose pipe , red coloured, ss jet nozzel, 25mm. isolating valve and all other neccessary fixing accesories complete in all respect. dsr no 17:1 86 supplying and fixing single headed internal hydrant valve with instantaneous gunmetal / stainless steel coupling of 63 mm dia with cast iron wheel isi marked conforming to is 5290 ( type a ) with blank gunmetal / stainless steel cap and chain as required :as per dsr & aor 2019 s.i. no. 9.1 87 supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to is 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : dsr & aor 2019si no. 18.1 88 supplying and fixing 63 mm dia, 15 m long rrl hose pipe with 63 mm dia male and female couplings duly bound with gi wire, rivets etc. conforming to is 636 ( type a ) as required : dsr & aor 2019 si.no.16.1 89 providing and fixinghose box ( 600x300x200 ) size of suitable size made out of 16 / 18 swg thick having central opening and 4 mm thick glazed glass double door including necessory rubber beading key pocket, handle locking arrengment painting with polyurethene based red paint etc. the words fire hose to be painted on the dooor as per approved drawing complete in all respect. mr 90 supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia ms pipe connection conforming to is 904 as required : 91 2 way 100 mm dia m.s. pipe si no. 19.1 92 supply, fixing, testing and commissioning of 25mm ball valve complete. mr 93 supplying and fixing air vessel made of 250 mm dia, 8 mm thick ms sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. dsr & aor 2019 si no. 20 94 supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: ( terrace pump ) ( a ) horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to is : 1520 ( b ) suitable hp squirell cage induction motor tefc type suitable for operation on 415 volts, 3 phase, 50 hz, ac supply with ip55 class of protection for enclosure, horiziontal foot mounted type with class f insulation, conforming to is 325. ( c ) m.s.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. ( d ) suitable cement concrete foundation duly plastered and with anti vibration pads.supplying and fixing air vessel made of 250 mm dia, 8 mm thick ms sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.1620 lpm at 70 m head dsr & aor2019 si no. 1.8 95 supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : ( diesel driven pump ) horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to is 1520. suitable hp, 1500 rpm water cooled with radiator, diesel engine conforming to relevant is standard complete with auto starting mechanism, 12 / 24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. m.s fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. suitable cement concrete foundation duly plastered and with anti vibration pads.make : kirloskar / other standard make.dsr no. 2.81620 lpm at 70 m head 96 supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : ( jockey pump ) a ) horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to is : 1520.b ) suitable hp squirell cage induction motor tefc type suitable for operation on 415 volts, 3phase 50 hz ac supply with ip 55 class of protection for enclosure, horizontal foot mounted type with class f insulation, conforming to is : 325.c ) m.s.fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. suitable cement concrete foundation duly plastered and with anti vibration pads. make kirloskar / other standard make dsr no. 3.2180 lpm at 70 m head 97 automatic control panel ( s ) fabrication, supply, insallation testing & commissioning of electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick crca sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, inter connection with suitable size copper conductor cable / solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per cpwd specification with following in coming and outgoings, suitable for operation on 415v, 3 phase, 50hz ac supply with enclosure protection class ip 42 as required : incoming 250a, 50ka 4 pole mccb, ics=100% icu rating digital voltmeter 0 500v with selector switchdigital ammeter ( 0 250 a ) with selector swtich & cts etc.outgoing main fire pump : 125 a 50ka tpn mccbjockey pump : 63 a , 50ka tpn mccb, diesel engin control complete in all respect dsr no. 5.1 98 providing & fixing of pressure switch in m.s. pipe line including connection etc. as required. dsr & aor 2019 si no. 22 99 providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required dsr 2018 si no. 16.8 100 sitc of foot valves with strainer at the suction pipe of fire pumps ( in case of negative suction only ) . make kalpana / kartarsir / advance or equivalent 101 150mm dia 102 100mm dia 103 supplying, fixing, testing and commissioning of butterfly valve of pn 1.6 rating with bronze / gunmetal seat duly isi marked complete with nuts, bolts, washers, gaskets conforming to is 13095 of following sizes as required : dsr & aor 2019 si no 11 104 150 mm dia 105 100 mm dia 106 80 mm dia 107 providing, installation, testing and commissioning of non return valve of following sizes confirming to is: 5312 complete with rubber gasket, gi bolts, nuts, washers etc.as required : dsr & aor2019 si no. 14 108 150 mm dia 109 100 mm dia 110 supply and fixingof c02 type fire extinguisher 4.5 kg. capacity ( isi marked is : 2878 & tac approved ) complete with initial charge and wall bracket, along with supply of all materials and labourfor proper completionof work.pwd sor 2018 si no 1132 111 supply and fixingof fire extinguisher, abc type 6.00 kg. capacity ( isi marked is : 15683 & tac approved ) complete with initial charge and wall bracket, along with supply of all materials and labourfor proper completionof work.pwd sor 2018 si no 1131 ( a ) 112 supply and fixing of self glow type exit sinage. 113 sitc ofsprinkler 68° deg, complete in all respects. ( make: omex / life guard / safex ) dsr 2019 si no. 21.1pendent type 114 fire alarm systemworksupplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices ( including detectors ) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics / lcd display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory ( eprom ) , power supply unit ( 230± 5% v, 50 hz ) , 48 hrs back up with 24 volt sealed maintenance free batteries with automatic charger. the panel shall have facility to connect printer to printout log and facility to have seamless integration with analog / digital voice evacuation system ( which is part of the schedule of work under sh: pa system ) and shall be complete with all accessories . the panel shall be compatible for ibms system with open protocol bacnet / modbus over ip complete as per specifications. dsr 2018 si no 17.2.1.1 115 ten loop panel. 116 supplying, installation, testing & commissioning of intelligent analog addressable photo thermal detector complete with mounting base complete as required. dsr 2018 si no 17.2.4 117 supplying, installation, testing & commissioning of response indicator on surface / recessed ms box having two led, metallic cover complete with all connections etc as required.dsr 2018 si no 17.2.5 118 supplying, installation, testing & commissioning of addressable phone control module complete as required. dsr 2018 si no 17.2.11 makeinnel / simplex / tyco 119 supplying, installation, testing & commissioning of addressable manual call point complete as required. dsr 2018 si no 17.2.14 120 supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. dsr 2018 si no 17.2.15 121 supplying, installation, testing & commissioning of addressable fire control module complete as required. dsr 2018 si no 17.2.10 122 supplying, installation, testing & commissioning of faultisolator complete with base as required. dsr 2018 si no 17.2.7 123 supplying, installation, testing & commissioning of repeater panel wih 320 character / touch screen lcd display with inbuilt reset ackowledge and silence switches complete as required.dsr 2018 si no 17.2.3 124 supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600 / 1000v rated with annealed copper conductor having xlpe insulation, steel wire armouring & frls outer sheath complete as required.. dsr 2018 si no. 17.5.2 125 supplyandlayingof aluminiumconductorpvcinsulated armoured served sheathed cables 1100 volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. on surface the cable run shall be fixed on m.s. clamps etc. of suitable size or as directed by the engineer incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. pwd sor 2018 si no 501 126 150 sqmm 3.5 core 127 supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. the armouring ofthe cable shall be properly connected with the earth as per direction of engineer incharge.pwd sor 2018 si no 503 128 150 sqmm 3.5 core 129 supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respects as per direction of the engineer incharge.pwd sor 2018 si no 504 130 70 sq mm 131 150 sqmm 132 supplying, installation, testing & commissioning of 6 zone, voice alarm controller with usb, mp3 player ( including 6 zonebutton paging station ) with seamless integration facility withmain fire alarm panel for voice evacuation complete asrequired dsr 2018 si.no.17.3.1 133 supplying, installation, testing & commissioning of 1.5 / 3 / 6w metal box ceiling / wall speakers complete as required.dsr 2018 si.no.17.3.3 134 supplying, installation, testing & commissioning of digital audio amplifier 50 watt, 25v rms operating at 240 volt ac supply complete as required.dsr 2018 si.no.17.3.6 135 supplying, installation, testing & commissioning of voice command keypad 6 zone, with microphone assembly complete as required.dsr 2018 si.no.17.3.9 136 street light worksupply and fixing of 7.0 meter long g.i. octogonal pole top dia 70 mm bottom dia 130 mm andbase plate 12 mm thick having3 mm thickness with single arm braclet ( 1 meter length ) on rcc foundatoion including the cost of foundation , foundation bolts, excavation & baack filling and required t&p complete fn all respect pwd sor 2018 s.i. no 641 137 supply and fixing of led street light fitting having die cast aluminium body and diffuser with driver set suitable for 110 to 130 watt. confirming to ip 66 protection complete in all respect pwd sor 2018s.i.no. 1424 cat aaa 138 providing, laying and fixing following dia g.i. pipe ( medium class ) in ground complete with g.i. fittings including trenching ( 75 cm deep ) and re filling etc as required dsr 2018 si no. 14.13.3 139 100 mm dia 140 supply and fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors , hrc fuses, isolatingswitch metering intrument & instrument box with cts etc. in case of tpn, comp;ete in all respect pwd sor 2018 s.i.no. 807 141 40 a tpn 142 supply and laying of 25mm x 3mm g.i. strip from earth electrode directly in the ground as required complete in all respect. pwd sor 2018 s.i.no. 716 143 supply and burring of safe earthing electrode t 19 ( hot dip galvanized ) , length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal dia 12 mm, outer gi pipe of 16 swg and inner gi pipe of 12 swg with hot dip galvanization up to 100 micron filled with crystalline conductive mixture ( ccm ) having anti corrosive & conductive property with 50 kgs activated soil ( bfc ) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square c.i. frame with hinged cover & masonry husing ( from electrode terminal to switch board, cost of 25 x 3 g.i . strip will be extra ) make: as approved in u.p. p.w.d., & c.p.r.i. certified. pwd sor 2018 s.i.no. 725 ( a ) 144 tubewell workboring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in is: 2800 ( part i ) , including collecting samples from different strata, preparing and submitting strata chart! bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90 metre depth below ground level. dsr 2019 sino. 23.1.1 145 350 mm dia upto 60 msino. 23.1.1.2 146 60 90 msi no. 23.1.1.1 147 90 150 msi no. 23.2.1.2 148 150 220 msi no. 23.2.1.2 149 220 300 m 150 supplying, assembling, lowering and fixing in vertical position in bore well, erw ( electric resistance welded ) fe 410 mild steel screwed and socketed / plain ended casing pipes of required dia, conforming to is: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of engineer in charge. dsr 2019 si no. 23.10 151 150 mm nominal size dia having minimum wall thickness 5.00 mm si no. 23.10.2 152 200 mm nominal size dia having minimum wall thickness 5.40 mm si no. 23.10.3 153 supplying, assembling, lowering and fixing in vertical position in bore well, erw ( electric resistance welded ) fe 410 plain slotted ( having slot of size 1.6 / 3.2 mm ) mild steel threaded and socketed / plain bevel ended pipe ( type a ) of required dia, conforming to is: 8110, of reputed and approved make, having wall thickness not less than 5.40 mru, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fitting & accessories, all complete, for all depths, as per direction of engineer in charge. dsr 2019 si no. 23.11 154 150 mm nominal size dia si no. 23.11.2 155 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assemblv of tube well as oer is:2800 ( dart n.dsr 2019 si no. 23.15 156 150 mm dia si no. 23.15.2 157 providing and fixing m.s. clamp of required dia to the top of casing! housing pipe of tube well as per is: 2800 ( part i ) , including necessary bolts & nuts of required size complete. dsr 2019 si no. 23.14 158 200 mm clamp si no. 23.14.3 159 supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of engineer in charge. dsr 2019 si no. 23.6 160 development of tube well in accordance with is : 2800 ( part 1 ) and is: 11189, to establish maximum rate of usable water yield without sand content ( beyond permissible limit ) , with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by v notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, ilc disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of engineer in charge dsr 2019 si no. 23.12 161 providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing! casing pipe, rmovable as per requirement, all complete for borewell of: dsr 2019 si no. 23.13 162 200 mm dia si no. 23.13.3 163 500 lpm 52 m head of k s b make submersible pumping plant 164 submersible pump set. 165 switch gear 166 main piping and valves 167 pressure & depth gauge 168 lifting tackle 169 installation 170 commissioning 171 painting 172 testing 173 supply of aquas make electronic chlorinator of 6lph capacity complete accessories and 100 ltr, pvc solution tank. 174 installation charges ( 1 / 2 socket fixed in pipe line to provide by the department, 175 sitc of 20 passenger stretcher lift 2 stop, 2 opening at same side with ss hairline finish fully automatic gate with side opening along with acv3 controller and gearless machine no. of lift speed 1.0 m / sload 1360 kgcapacity 20 passengerfloor g + 1car travel 7000 mmhoist way dimension 2400mm wide x 2800mm deep ( required ) overgead 4500 mmpit depth 1500 mmcar dimension 1300mm wide x 2400mm deep x 2200mm highdoor opening 1000mm wide x 2000mm highelectric supply 415 volts, 3 phase, 50hz, ac 176 main lt paneldesign, manufacturing, supply installation, testing & commissioning of lt switchgear panels suitable for 433 v, 3 phase, 4 wire, 50 hz power distribution system. the panel shall be indoor, free standing, floor mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type compartmentalised design fabricated out of 14 swg crca sheet steel, complete with colour coded, heat shrinkable pvc insulated, aluminium bus bars and separate earth bus bar of adequate cross section through out the length of the panel. the incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable alley, bus bar alley / chamber. the panel shall be complete with name plate, earthing, numbering, danger plate etc. as required and as per specifications and drawings. the panel shall withstand the fault level of 25ka.a ) 1 no. incoming 1250a fp 50ka manually operated drawout type acb with numerical o / c, s / c& e / f release, ct, metering, compelete with all fuses wiring etc and as per sld. for 630kva css incomerb ) 1 no. outgoing 630a 35ka tp mccb with extended rhom along with o / c & s / c protection along with ammeter with ammeter selector switch, ct etc. c ) 1 no. outgoing 400a 35ka tp mccb d ) 3 nos. outgoing 250a 25ka tp mccb e ) 4 nos. outgoing 200a 25ka tp mccb f ) 4 nos. outgoing 160a 25ka tp mccb g ) 1 no. outgoing 125a 25ka tp mccb h ) 2 nos. outgoing 100a 25ka tp mccb i ) 3 nos. outgoing 63a 25ka tp mccb 177 normal floor panels supply installation, testing & commissioning of normal floor panels suitable for 433 v, 3 phase, 4 wire, 50 hz. the panel / dbshall be indoor, sheet metal clad, cubicle, dead front, dust and vermin prooffabricated out of crca sheet steel, complete with colour coded, bus bars and separate earth connection of adequate capacity. the incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable box / alley. the panel / dbshall be complete with name plate, earthing, numbering, danger plate etc. as required and as per specifications and drawings. the panelshall withstand the fault level of 10ka. 178 ground floor panel ( wing a ) normal supplya ) 1no. incoming 160a ( 16ka ) fp mccb with standard incomer metering b ) 7 nos. outgoing 63a fp mcb ( 10ka ) 179 ground floor panel ( wing b ) normal supplya ) 1no. incoming 200a ( 16ka ) fp mccb with standard incomer meteringb ) 2 nos. outgoing 63a tp mccb ( 16ka ) b ) 6 nos. outgoing 63a fp mcb ( 10ka ) 180 ground floor panel ( wing c ) normal supplya ) 1no. incoming 250a ( 16ka ) fp mccb with standard incomer meteringb ) 1 nos. outgoing 100a tp mccb ( 16ka ) c ) 6 nos. outgoing 63a fp mcb ( 10ka ) 181 first floor panel ( wing a ) normal supplya ) 1no. incoming 160a ( 16ka ) fp mccb with standard incomer meteringb ) 7 nos. outgoing 63a fp mcb ( 10ka ) 182 first floor panel ( wing b ) normal supplya ) 1no. incoming 160a ( 16ka ) fp mccb with standard incomer meteringb ) 7 nos. outgoing 63a fp mcb ( 10ka ) 183 first floor panel ( wing c ) normal supplya ) 1no. incoming 200a ( 16ka ) fp mccb with standard incomer meteringb ) 2 nos. outgoing 63a tp mccb ( 16ka ) c ) 6 nos. outgoing 63a fp mcb ( 10ka ) 184 emergency floor panelsdesign, manufacturing, supply installation, testing & commissioning of emergency floor panels / vtpn db suitable for 433 v, 3 phase, 4 wire, 50 hz. the panel / dbshall be indoor, sheet metal clad, cubicle, dead front, dust and vermin prooffabricated out of crca sheet steel, complete with colour coded, bus bars and separate earth connection of adequate capacity. the incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable box / alley. the panel / dbshall be complete with name plate, earthing, numbering, danger plate etc. as required and as per specifications and drawings. the panel / dbshall withstand the fault level of 10ka 185 ground floor panel ( wing a ) & ( wing b ) emergency supplya ) 1no. incoming 100a ( 16ka ) fp mccb with standard incomer meteringb ) 7 nos. outgoing 40a fp mcb ( 10ka ) 186 ground floor panel ( wing c ) emergency supplya ) 1no. incoming 125a ( 16ka ) fp mccb with standard incomer meteringb ) 1nos. outgoing 63a tp mccb ( 16ka ) c ) 6 nos. outgoing 40a fp mcb ( 10ka ) 187 first floor panel ( wing a ) emergency supplya ) 1no. incoming 125a ( 16ka ) fp mccb with standard incomer meteringb ) 1 nos. outgoing 63a tp mcb ( 10ka ) c ) 6 nos. outgoing 40a fp mcb ( 10ka ) 188 first floor panel ( wing b ) & ( wing c ) emergency supplya ) 1no. incoming 160a ( 16ka ) fp mccb with standard incomer meteringb ) 2 nos. outgoing 63a tp mccb ( 16ka ) b ) 7 nos. outgoing 40a fp mcb ( 10ka ) ...

Urban Development Department - Uttar Pradesh

31657848 bids are invited for as per mention in spacification total quantity : 2 tender for 4.5 meter width ornamnetal arrangement supply and laying of aluminum conductor pvc insulated armoured served sheathed cables 1100 volts grade, providing and fixing 6 swg dia g.i wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain / wiring / cable, s / f and floowing capacity of automatic street light cubicle control pannel painted with anticorrosive alkali and acid proof paint consisting of time switch tso 100 series with contractors hrc fuse isolating switch metering instrument and instrument box with cts etc...

Urban Development Department - Uttar Pradesh

30590818 bids are invited for high mast complete supply & fixing of 16 mtr high mast shaft of approved make with rising system hot dip glavanized inside & out side dip,heaving pole sheet thickness 3 mm. top dia minium 150 mm, bottom dia 360 mmbase plate 32 mm thick suitable for wind velocity as per is 875 part 3 &having no circumferential weld, with accessories for high mast such as head frame suitable for 6 to 12 luminaries & its control gear boxes 1.5 hp power tool moter, 3 point suspension system with steel wire rope 6 mm dia, double drum winch, including making suitable foundation as per manufature drawing/ site reuiment along with foundation bolts nuts, washers, anchor plates etc complete in all respect. (pwd s.i. no. 652 / 2018) , led lights supply and fixing offactory wired integral led flood light luminaires with die cast aluminium housing built with dirver set suitable for 170 to 200 watt. confirming to ip 66 protection complete in all respect and high power led with lenses, > 110lm/w, pf>0.95, thd<10% at full load, cri>70, potted driver set (not circuitory), phase to phase protection at 440 v & > 300v auto cut and re start feature, with 5 year warranty.pwd sor 1455 , high mast aviation light supply of led type single dome aviation obstruction light. pwd sor 409 , earthing supply and burring of safe earthing electrode t 39 cu copper coated, length up to 3000mm, outer pipe 76.3mm x 3.2 inner pipe 42.4mm x 2.6mm, terminal dia 12mm, coating 80 100 micron filled with crystalline conductive mixture (ccm) having anti corrosive & conductive property with 50 kgs activated soil (bfc) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square c.i. frame with hinged cover & masonry housing. (from electrode terminal to switch board, cost of 25 x 3 copper strip will be extra). make: as approved in u.p. p.w.d., & c.p.r.i. certified.(s.i. no. 726d / 2018) , control panel supply and fixing of 63 amp. tpn of of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn, for the automatic switching of luminaries, power tool control with 2 no 9a contactors and raise lower push button, complete in all respect. m.r. , cable s/l of “al” conductor pvc insulated armoured, served, sheathed cable 1100 volts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround & protected with burnt bricks on sides & on top. on surface the cable run shall be fixed on ms clamps etc. of suitable size or as directed by the e/i, comp. in all resp. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. 50mm sq. mm 3.5 core.pwd sor 501 (l) , gi strip supply and laying of 32 mm x 6 mm g.i. strip from earth electrode directly in the ground as required complete in all respect. (s.i. no. 717 / 2018) , dwc pipe supplying and laying of 120 mm dia. (od 120 mm & id 103 mm nominal) dwc hdpe pipe isi marked along with all accessories like socket, bend, couplers etc. conforming to is 14930, part ii complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. (dsr no. 14.16.3 / 2018) (341 12% gst = 300.08) , lug supply and fixing of plain or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the engineer incharge. 16 sq. mm pwd sor 504 (d) total quantity : 1...

Urban Development Department - Uttar Pradesh

30574457 bids are invited for pole supply & fixing of 10 mtr gi octagonal pole of approved make ( top dia 100mm, bottom dia 200mm and base plate 16mm thik ) having 3 mm thikness with single arm bracket 1 mtr length in 1:2:4 rcc foundation bolt including the cost of foundation, excavation & back filling and required t&p completee in all respect. s.no. 649 , led flood light luminaires with die cast aluminium housing built with dirver set suitable for 140 to 150 watt. supply and fixing of factory wired integral led flood light luminaires with die cast aluminium housing built with dirver set suitable for 140 to 150 watt. confirming to ip 66 protection complete in all respect. cat aaa s.no.1454 , conductor supply and laying of aluminium conductor pvc insulated armoured served sheathed cables 1100 volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. on surface the cable run shall be fixed on m.s. clamps etc. of suitable size or as directed by the engineer incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. 16 sq. mm 2 core 501 ( i ) , gi pipe of 12 swg with supply and burring of safe earthing of safe earthing electrode t 19, ( hot dip galvanized ) , length up to 3000mm, outer dia 50 mm inner dia 25 mm, terminal dia 12mm, outer gi pipe of 16 swg and inner gi pipe of 12 swg with hot dip galvanization up to 100 micron filled with crystalline conductive mixture ( ccm ) having anti corrosive & conductive property with 50 kgs activated soil ( bfc ) capable of reducing the soid resistivity with good mixture of retaining capacity and one earthing lead of 25mm x 3mm g.i. strip, upto switch board ( from apron to switch board, the cost of g.i. strip will be extra ) along with 30 cm square c.i. frame with hinged cover & masonry housing. make: as approved in u.p. p.w.d., & c.p.r.i. certified. s.no.725 ( b ) , control panel supply and laying of 25mm 3mm strips from earth electro directly in the graund up to control pannel as required complete in all respect ( m.r. ) , single core copper conductor cable. supply and wiring of submain with two number 2.5 sq. mm frlsh pvc insulated 1100v grade multistrand single core copper conductor cable. s.i. no. 1301 ( b ) 148 , 25mm × 3mm g.i strip from earth electrode directly supply and laying of 25mm 3mm strips from earth electro directly in the graund up to control pannel as required complete in all respect ( m.r. ) , 1.5 sq. mm to 2.5 sq. mm cables, supply and fixing of crimping, copper tin electroplated lugs of dowells / ismail make suitable for 1.5sq. mm to 2.5 sq. mm cable, inclding tapping with insulating tape, comlete in all respect. s.i no. 1129 , pin type copper tin plated cable socket ( lug ) 16 sq. mm supp;y & fixingof plain or pin type copper tin plated cable socket ( lug ) 16 sq. mm to the cable, insulated with tape and making connection etc. complete in all respected as per direction of the engineer incharge. s.i. no. 504 ( d ) , automatic steet light cubicle control panel painted supply and fixing following capacity of automatic steet light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn, complete in all respect. s.no.807 ( f ) ( ii ) total quantity : 1...

Urban Development Department - Uttar Pradesh

30535987 bids are invited for 9 mtr high mast pole supply & fixing of 9 mtr. gi octagonal pole of approved make ( top dia 70mm bottom dia155 mmandbaseplate12mmthik ) having 3mmthiknesswith single arm. sl. no. 645 , armoured cable 16x4 sq. mm supplyof armoured cable 16x4 sq. mm ( schedule item no. 501 ( 1 ) , laying installation cable laying chargesincluding brick and sandwith labourcharges. , copper wire1.5x3 core. supplyof copper wire1.5x3 core. , fues set &sonnector supplyforfusesetandconnector to functionbox. , led street light 75 to 90 w supply&fixingofledstreet light fitting havingdie cast aluminiumbodyanddiffuserwith driversetsuitablefor75to90 watt, confirmingtoip66and aboveprotection complete inall respect ( scheduleitemno.1423 ) . cat aaa , safe earthing electrode supply and burring of safe earthing electrode t 39 ( hot dip galvanized ) length up to 3000 mm, outerpipe 76mm inner dia38 mm terminaldia12 mmoutergi pipe of16swgandinnter gi pipe of 12 swg with hotdip galvanizationupto100micron filled with crystalline conductive mixture ( ccm ) havinganti corrosive&conductiveproperty with 50 kgs. activatedsoil ( bfc ) capable of reducing the soil resistivity with good ixture of retaining capacity along with 30 cm square c.i. frame with hinged cover & masonary housing ( from electrode terminal to switch board, cost of 25 x 3 g.i. strip will be extra ) ( sr. no. 725 ( d ) ] , automatic street light cubical control panel supply and fixing of 25 a spn capacity of automatic street light cubical control panel painted with anticorrosive alkali and acid proof paint consisting of time switch ts0 100 series with contractors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn complete in all respect s.i. no. 807 ( b ) ( 2 ) total quantity : 1...

Urban Development Department - Uttar Pradesh

30535912 bids are invited for s&f of7.0m gi octagonal pole with 70 to 90 watt. led light with all component. ( the competent authority may release 50% amountof the total cost after successfully supply of goods given in bid ) . 1. supply & fixing of 7 mtr. octagonal pole of approved make ( top dia 70mm ) , bottom dia 130mm and base plate 12 mm thickness with single bracket ( 1 mtr. length ) on rcc foundation including bolts, excavation & black filling and required t&p complete all respect. 100 nos 2. supply and laying of aluminium conductor pvc insulated armoured served cable 16sq mm x 2 core 2500 mtr 3. supply and fixing of led street light fitting having dia cast aluminium body and diffuser with driver set suitable for 70 to 90 watt. confirming to ip 66 protection complete in all respect. cat aaa 100 nos 4. supply and burring of safe earthing electrode t 39 ( hot dip galvanized ) , length up to 3000mm pwd sl no 725.b 100 nos 5. supply and fixing of following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof pint consisting of time switch with contractors hrc fuses isolation switch 40 amp. 4 nos 6. wiring point for light on pole 1.5 sq. mm copper wire. 100 nos 7. gi pipe b class. 50 mm. 100 mtr 8. supply and laying of aluminium conductor pvc insulated armoured served cable 35sq mm x 3½ core. 200 mtr , ict service ready to successfully work on each place ( the competent authority may release rest 50% amountof the total cost after successfully installation of goods given in bid ) installation of pole with light under the area of nagar palika parishad as per bid requirement total quantity : 1...

Urban Development Department - Uttar Pradesh

30532613 bids are invited for s&f of7.0m gi octagonal pole with 70 to 90 watt. led light with all component. ( the competent authority may release 50% amountof the total cost after successfully supply of goods given in bid ) . 1. supply & fixing of 7 mtr. octagonal pole of approved make ( top dia 70mm ) , bottom dia 130mm and base plate 12 mm thickness with single bracket ( 1 mtr. length ) on rcc foundation including bolts, excavation & black filling and required t&p complete all respect. 100 nos 2. supply and laying of aluminium conductor pvc insulated armoured served cable 16sq mm x 2 core 2500 mtr 3. supply and fixing of led street light fitting having dia cast aluminium body and diffuser with driver set suitable for 70 to 90 watt. confirming to ip 66 protection complete in all respect. cat aaa 100 nos 4. supply and burring of safe earthing electrode t 39 ( hot dip galvanized ) , length up to 3000mm pwd sl no 725.b 100 nos 5. supply and fixing of following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof pint consisting of time switch with contractors hrc fuses isolation switch 40 amp. 4 nos 6. wiring point for light on pole 1.5 sq. mm copper wire. 100 nos 7. gi pipe b class. 50 mm. 100 mtr 8. supply and laying of aluminium conductor pvc insulated armoured served cable 35sq mm x 3½ core. 200 mtr , ict service ready to successfully work on each place ( the competent authority may release rest 50% amountof the total cost after successfully installation of goods given in bid ) installation of pole with light under the area of nagar palika parishad as per bid requirement total quantity : 1...

Nagar Palika Nigam - Uttar Pradesh

30522104 bids are invited for supply and fixingof 12.5 mtr semi highmast atausanganj & bhadau chungi pole with assessories s/f of 12.5 mtr. high mast shift of approved make with rising system hot dip glavanized inside and outside dip heaving pole sheet thickness 3 mm. top dia minium 150mm, bottom dia 310 mm., base plate 25mm. thick suitable for wind velocity as per is 875 part 3 and having no circumferential weld with accessories for high mast such as head frame suitable for 6 luminaries & its control gear boxes 0.75 hp power tool motor, 3 point suspension system with steel wire rope 6mm dia, double drum winch including making suitable foundation as per manufacture drawing/site include reuiment along with foundation bolts, nuts, washers, anchor plates etc. complete in all respect having 05 years warranty & guaranty with replacement as per engineer incharge.(si no 651 year 2018) , led flood light with assessories s/f of factory wired integral led floold light luminaries with die cast aluminum housing and lenses built with mandatory driver sat suitable for200 watt. confirming to ip 66 protection. complete in all respect including labour. (si no 1455 year 2018) , earthing s/b of600mmx600mmx6mm gi plate vertically for earthling with its top at least 3metres below ground level complete with 20mm dia gi pipe and funnel for watering and one earthling lead of one no. 8 to 10 swg gi wire in 15 mm dia gi pipe up to switch board 30cm square ci frame with hinged cover masonry housing alternate layers of charcoal/ coke and salt at least 150mm thick all round etc. complete in all respect.(si no 702 year 2018) , control panel s/f of40a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors hrc fuses, isolating switch metering instrument and instrument box with cts etc. in case of tpn, complete in all respect.(si no 807f (ii) year 2018) , cable wire s/l aluminum conductor pvc insulated armored served sheathed cables 1100 volts rating 16sq mm x 4 core. complete in all respect. (si no 501 (i) year 2018) , signaboard s/f of innaugration stone brighter gold letter including all complete total quantity : 1...

Urban Development Department - Uttar Pradesh

30485013 bids are invited for s&f of7.0m gi octagonal pole with 70 to 90 watt. led light with all component. ( the competent authority may release 50% amountof the total cost after successfully supply of goods given in bid ) . 1. supply & fixing of 7 mtr. octagonal pole of approved make ( top dia 70mm ) , bottom dia 130mm and base plate 12 mm thickness with single bracket ( 1 mtr. length ) on rcc foundation including bolts, excavation & black filling and required t&p complete all respect. 100 nos2. supply and laying of aluminium conductor pvc insulated armoured served cable 16sq mm x 2 core 2500 mtr3. supply and fixing of led street light fitting having dia cast aluminium body and diffuser with driver set suitable for 70 to 90 watt. confirming to ip 66 protection complete in all respect. cat aaa 100 nos4. supply and burring of safe earthing electrode t 39 ( hot dip galvanized ) , length up to 3000mm pwd sl no 725.b 100 nos5. supply and fixing of following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof pint consisting of time switch with contractors hrc fuses isolation switch 40 amp. 4 nos6. wiring point for light on pole 1.5 sq. mm copper wire. 100 nos7. gi pipe b class. 50 mm. 100 mtr8. supply and laying of aluminium conductor pvc insulated armoured served cable 35sq mm x 3½ core. 200 mtr , ict service ready to successfully work on each place ( the competent authority may release rest 50% amountof the total cost after successfully installation of goods given in bid ) installation of pole with light under the area of nagar palika parishad as per bid requirement total quantity : 1...

Urban Development Department - Uttar Pradesh

30457970 bids are invited for highmast pole supply & fixing of 12.5 meter high mast lighting system pole of approved make with polygonal, tapered and flange mounted type, with rising system, totally hot dip galvanized inside and outside, having pole sheet thickness 3mm. bottom dia 310mm, base plate 25mm thick suitable for wind velocity as per is 875 part 3 & having no circumferential weld, with accessories for 12.5 meter high mast such as head frame, lighting arrester, 0.75hp power tool motor, 6mm wire rope made of stainless steel, double drum winch, winch bracket, power trailing cable, integral power tool, compensating disc, galvanized lantern carriagesuitable for mounting of 6 luminaries ofenergy efficient led flood light. foundation as per manufacturer drawing and along with foundation bolts, nits, washers, anchor plate, etc. complete in all respect. ( pwd srl. no. 651 ) , highmast cable etc supply & laying of 16 sq. mm. 4 core aluminium conductor pvc insulated armoured served sheathed cable, 1100 volts garde, at a depth of 750mm below ground level over a cushion of 75mm sand and all around protected with burnt bricks on sides and top. on surface the cable run shall be fixed on m.s. clamps etc. of suitable size or as directed by engineer in charge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clampsetc. ( pwd srl. no.501 i ) , highmast earthing electrod supply & burying of safe earthing electrod t 39 ( hot dip galvanized ) , length upto 3000mm, , outer pipe 76.3mm x 3.2mm inner pipe 42.4 x 2.6mm, terminal dia 12mm, coating 80 100 micron filled with crystalline conductive mixture ( ccm ) having anti corrosive and conductive property with 50 kgs activated soil ( bfc ) capable of reducing the soil restivity with good mixture of retaining capacity along with 30cm square c.i. frame with hinged cover and masonry housing. ( from electrode terminal to switch board, cost of 25x3mm copper strip will be extra ) . make: as approved in u.p.p.w.d. &c.p.r.i. certified. ( pwd srl no. 727 ( d ) ) , highmast flood light supply & fixing of factory wired integral led flood light luminaries with die cast aluminium housing and lenses built with mandatory driver set suitable for 120w. conforming to ip 65 / 66 protection complete in all respect. u.p.p.w.d. cat. reference aa / aaa approved. ( pwd srl. no. 1455 ) , highmast tpn supply and fixing of 40 amp. tpn of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contractors, hrc fuse, isolating switch metering instrument and instrument box with cts etc. complete in all respect. ( pwd ) srl. no. 807 ( f ii ) ) , highmast aviation supply and fixing of single unit ledaviation obstruction light complete with transformer and led spiral etc. , highmast foundtation making of concrete foundation & erection of high mast lights as per approved drawing or as per thedirection of engineer in –charge. total quantity : 1...

Nagar Palika Nigam - Uttar Pradesh

30457934 bids are invited for supply and fixingof 9.0 mtr. gi octagonal pole at police commissisner camp office / awas varanasi.pole with assessories s / f of 9.0 mtr. gi octagonal pole of approved make ( top dia 70mm bottom dia 155mm and base plate 12mm thik ) having 3mm thikness on rcc foundation including the cost of foundation, foundation bolts excavation and back filling and required t&p complete in all respects ( si no 645year 2018 ) , led flood light with assessories s / f of factory wired integral led floold light luminaries with die cast aluminum housing and lenses built with mandatory driver sat suitable for 120 watt. confirming to ip 66 protection. complete in all respect including labour. ( si no 1453 year 2018 ) , earthing s / b of600mmx600mmx6mm gi plate vertically for earthling with its top at least 3metres below ground level complete with 20mm dia gi pipe and funnel for watering and one earthling lead of one no. 8 to 10 swg gi wire in 15 mm dia gi pipe up to switch board 30cm square ci frame with hinged cover masonry housing alternate layers of charcoal / coke and salt at least 150mm thick all round etc. complete in all respect. ( si no 702 year 2018 ) , control panel s / f of40a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors hrc fuses, isolating switch metering instrument and instrument box with cts etc. in case of tpn, complete in all respect. ( si no 807f ( ii ) year 2018 ) , cable wire s / l aluminum conductor pvc insulated armored served sheathed cables 1100 volts rating 10sq mm x 4 core. complete in all respects. ( si no 501 ( h ) year 2018 ) , busbar fuse unit supply and fixing of busbar fuse unit. complete in all respects. ( market rate ) , factory made gi 40mm dia ring supply and fixing of factory made gi 40mm dia ring radious 1mtr. surrounding in all respects. ( market rate ) total quantity : 1...

Nagar Palika Nigam - Uttar Pradesh

30456368 bids are invited for supply and fixingof 9.0 mtr. gi octagonal pole at nawapura_chauhatta & alampura varanasi.pole with assessories s / f of 9.0 mtr. gi octagonal pole of approved make ( top dia 70mm bottom dia 155mm and base plate 12mm thik ) having 3mm thikness on rcc foundation including the cost of foundation, foundation bolts excavation and back filling and required t&p complete in all respects ( si no 645year 2018 ) , led flood light with assessories s / f of factory wired integral led floold light luminaries with die cast aluminum housing and lenses built with mandatory driver sat suitable for 120 watt. confirming to ip 66 protection. complete in all respect including labour. ( si no 1453 year 2018 ) , earthing s / b of600mmx600mmx6mm gi plate vertically for earthling with its top at least 3metres below ground level complete with 20mm dia gi pipe and funnel for watering and one earthling lead of one no. 8 to 10 swg gi wire in 15 mm dia gi pipe up to switch board 30cm square ci frame with hinged cover masonry housing alternate layers of charcoal / coke and salt at least 150mm thick all round etc. complete in all respect. ( si no 702 year 2018 ) , control panel s / f of40a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors hrc fuses, isolating switch metering instrument and instrument box with cts etc. in case of tpn, complete in all respect. ( si no 807f ( ii ) year 2018 ) , cable wire s / l aluminum conductor pvc insulated armored served sheathed cables 1100 volts rating 10sq mm x 4 core. complete in all respects. ( si no 501 ( h ) year 2018 ) , busbar fuse unit supply and fixing of busbar fuse unit. complete in all respects. ( market rate ) , factory made gi 40mm dia ring supply and fixing of factory made gi 40mm dia ring radious 1mtr. surrounding in all respects. ( market rate ) total quantity : 1...

Nagar Palika Nigam - Uttar Pradesh

30453394 bids are invited for supply and fixingof 9.0 mtr. gi octagonal pole at naya mahadev & nachani mai mandir varanasi.pole with assessories s / f of 9.0 mtr. gi octagonal pole of approved make ( top dia 70mm bottom dia 155mm and base plate 12mm thik ) having 3mm thikness on rcc foundation including the cost of foundation, foundation bolts excavation and back filling and required t&p complete in all respects ( si no 645year 2018 ) , led flood light with assessories s / f of factory wired integral led floold light luminaries with die cast aluminum housing and lenses built with mandatory driver sat suitable for 120 watt. confirming to ip 66 protection. complete in all respect including labour. ( si no 1453 year 2018 ) , earthing s / b of600mmx600mmx6mm gi plate vertically for earthling with its top at least 3metres below ground level complete with 20mm dia gi pipe and funnel for watering and one earthling lead of one no. 8 to 10 swg gi wire in 15 mm dia gi pipe up to switch board 30cm square ci frame with hinged cover masonry housing alternate layers of charcoal / coke and salt at least 150mm thick all round etc. complete in all respect. ( si no 702 year 2018 ) , control panel s / f of40a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors hrc fuses, isolating switch metering instrument and instrument box with cts etc. in case of tpn, complete in all respect. ( si no 807f ( ii ) year 2018 ) , cable wire s / l aluminum conductor pvc insulated armored served sheathed cables 1100 volts rating 10sq mm x 4 core. complete in all respects. ( si no 501 ( h ) year 2018 ) , busbar fuse unit supply and fixing of busbar fuse unit. complete in all respects. ( market rate ) , factory made gi 40mm dia ring supply and fixing of factory made gi 40mm dia ring radious 1mtr. surrounding in all respects. ( market rate ) total quantity : 1...

Nagar Palika Nigam - Uttar Pradesh

30406861 bids are invited for supply and fixingof 9.0 mtr. gi octagonal pole at police commissisner camp office / awas varanasi.pole with assessories s / f of 9.0 mtr. gi octagonal pole of approved make ( top dia 70mm bottom dia 155mm and base plate 12mm thik ) having 3mm thikness on rcc foundation including the cost of foundation, foundation bolts excavation and back filling and required t&p complete in all respects ( si no 645year 2018 ) , led flood light with assessories s / f of factory wired integral led floold light luminaries with die cast aluminum housing and lenses built with mandatory driver sat suitable for 120 watt. confirming to ip 66 protection. complete in all respect including labour. ( si no 1453 year 2018 ) , earthing s / b of600mmx600mmx6mm gi plate vertically for earthling with its top at least 3metres below ground level complete with 20mm dia gi pipe and funnel for watering and one earthling lead of one no. 8 to 10 swg gi wire in 15 mm dia gi pipe up to switch board 30cm square ci frame with hinged cover masonry housing alternate layers of charcoal / coke and salt at least 150mm thick all round etc. complete in all respect. ( si no 702 year 2018 ) , control panel s / f of40a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors hrc fuses, isolating switch metering instrument and instrument box with cts etc. in case of tpn, complete in all respect. ( si no 807f ( ii ) year 2018 ) , cable wire s / l aluminum conductor pvc insulated armored served sheathed cables 1100 volts rating 10sq mm x 4 core. complete in all respects. ( si no 501 ( h ) year 2018 ) , busbar fuse unit supply and fixing of busbar fuse unit. complete in all respects. ( market rate ) , factory made gi 40mm dia ring supply and fixing of factory made gi 40mm dia ring radious 1mtr. surrounding in all respects. ( market rate ) total quantity : 1...

Nagar Palika Nigam - Uttar Pradesh

30400896 bids are invited for supply and fixingof 9.0 mtr. gi octagonal pole at rohaniya vidhansabha different places varanasi.pole with assessories s / f of 9.0 mtr. gi octagonal pole of approved make ( top dia 70mm bottom dia 155mm and base plate 12mm thik ) having 3mm thikness on rcc foundation including the cost of foundation, foundation bolts excavation and back filling and required t&p complete in all respects ( si no 645year 2018 ) , led flood light with assessories s / f of factory wired integral led floold light luminaries with die cast aluminum housing and lenses built with mandatory driver sat suitable for 120 watt. confirming to ip 66 protection. complete in all respect including labour. ( si no 1453 year 2018 ) , earthing s / b of600mmx600mmx6mm gi plate vertically for earthling with its top at least 3metres below ground level complete with 20mm dia gi pipe and funnel for watering and one earthling lead of one no. 8 to 10 swg gi wire in 15 mm dia gi pipe up to switch board 30cm square ci frame with hinged cover masonry housing alternate layers of charcoal / coke and salt at least 150mm thick all round etc. complete in all respect. ( si no 702 year 2018 ) , control panel s / f of40a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors hrc fuses, isolating switch metering instrument and instrument box with cts etc. in case of tpn, complete in all respect. ( si no 807f ( ii ) year 2018 ) , cable wire s / l aluminum conductor pvc insulated armored served sheathed cables 1100 volts rating 10sq mm x 4 core. complete in all respects. ( si no 501 ( h ) year 2018 ) , busbar fuse unit supply and fixing of busbar fuse unit. complete in all respects. ( market rate ) , factory made gi 40mm dia ring supply and fixing of factory made gi 40mm dia ring radious 1mtr. surrounding in all respects. ( market rate ) total quantity : 1...

Nagar Palika Nigam - Uttar Pradesh

30400893 bids are invited for supply and fixingof 9.0 mtr. gi octagonal pole at cantt. vidhansabha different places varanasi.pole with assessories s / f of 9.0 mtr. gi octagonal pole of approved make ( top dia 70mm bottom dia 155mm and base plate 12mm thik ) having 3mm thikness on rcc foundation including the cost of foundation, foundation bolts excavation and back filling and required t&p complete in all respects ( si no 645year 2018 ) , led flood light with assessories s / f of factory wired integral led floold light luminaries with die cast aluminum housing and lenses built with mandatory driver sat suitable for 120 watt. confirming to ip 66 protection. complete in all respect including labour. ( si no 1453 year 2018 ) , earthing s / b of600mmx600mmx6mm gi plate vertically for earthling with its top at least 3metres below ground level complete with 20mm dia gi pipe and funnel for watering and one earthling lead of one no. 8 to 10 swg gi wire in 15 mm dia gi pipe up to switch board 30cm square ci frame with hinged cover masonry housing alternate layers of charcoal / coke and salt at least 150mm thick all round etc. complete in all respect. ( si no 702 year 2018 ) , control panel s / f of40a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors hrc fuses, isolating switch metering instrument and instrument box with cts etc. in case of tpn, complete in all respect. ( si no 807f ( ii ) year 2018 ) , cable wire s / l aluminum conductor pvc insulated armored served sheathed cables 1100 volts rating 10sq mm x 4 core. complete in all respects. ( si no 501 ( h ) year 2018 ) , busbar fuse unit supply and fixing of busbar fuse unit. complete in all respects. ( market rate ) , factory made gi 40mm dia ring supply and fixing of factory made gi 40mm dia ring radious 1mtr. surrounding in all respects. ( market rate ) total quantity : 1...

Nagar Palika Nigam - Uttar Pradesh

30398940 bids are invited for supply and fixingof 9.0 mtr. gi octagonal pole at naya mahadev & nachani mai mandir varanasi.pole with assessories s / f of 9.0 mtr. gi octagonal pole of approved make ( top dia 70mm bottom dia 155mm and base plate 12mm thik ) having 3mm thikness on rcc foundation including the cost of foundation, foundation bolts excavation and back filling and required t&p complete in all respects ( si no 645year 2018 ) , led flood light with assessories s / f of factory wired integral led floold light luminaries with die cast aluminum housing and lenses built with mandatory driver sat suitable for 120 watt. confirming to ip 66 protection. complete in all respect including labour. ( si no 1453 year 2018 ) , earthing s / b of600mmx600mmx6mm gi plate vertically for earthling with its top at least 3metres below ground level complete with 20mm dia gi pipe and funnel for watering and one earthling lead of one no. 8 to 10 swg gi wire in 15 mm dia gi pipe up to switch board 30cm square ci frame with hinged cover masonry housing alternate layers of charcoal / coke and salt at least 150mm thick all round etc. complete in all respect. ( si no 702 year 2018 ) , control panel s / f of40a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors hrc fuses, isolating switch metering instrument and instrument box with cts etc. in case of tpn, complete in all respect. ( si no 807f ( ii ) year 2018 ) , cable wire s / l aluminum conductor pvc insulated armored served sheathed cables 1100 volts rating 10sq mm x 4 core. complete in all respects. ( si no 501 ( h ) year 2018 ) , busbar fuse unit supply and fixing of busbar fuse unit. complete in all respects. ( market rate ) , factory made gi 40mm dia ring supply and fixing of factory made gi 40mm dia ring radious 1mtr. surrounding in all respects. ( market rate ) total quantity : 1...

Urban Development Department - Uttar Pradesh

30338609 bids are invited for pole supply & fixing of 12.5 meter high mast shaft of approved make with rising system hot dip glavanized inside & out side dip, heaving pole sheet thickness 4 mm. , led flood light luminaires with die cast aluminium housing built with dirver set suitable for 170 to 200 watt. supply and fixing of factory wired integral led flood light luminaires with die cast aluminium housing built with dirver set suitable for 170 to 200 watt. confirming to ip 66 protection complete in all respect. cat aaa s.no.1455 , conductor supply and lying of 16 sq.mm 4 core aluminum conductor pvc insulated armoured served sheathed cable 1100 volt grade at depth 750 mm below ground level over a cushion of 75 mm thik sand all around and protected with brunt bricks on sided and top complete in all respect as per pwd schedule no.501 ( 1 ) , gi pipe of 12 swg with supply and burring of safe earthing of safe earthing electrode t 19, ( hot dip galvanized ) , length up to 3000mm, outer dia 50 mm inner dia 25 mm, terminal dia 12mm, outer gi pipe of 16 swg and inner gi pipe of 12 swg with hot dip galvanization up to 100 micron filled with crystalline conductive mixture ( ccm ) having anti corrosive & conductive property with 50 kgs activated soil ( bfc ) capable of reducing the soid resistivity with good mixture of retaining capacity and one earthing lead of 25mm x 3mm g.i. strip, upto switch board ( from apron to switch board, the cost of g.i. strip will be extra ) along with 30 cm square c.i. frame with hinged cover & masonry housing. make: as approved in u.p. p.w.d., & c.p.r.i. certified. s.no.725 ( b ) , control panel supply and fixing following capacity of automatic steet light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn, complete in all respect. s.no.807 ( f ) ( ii ) , single core copper conductor cable. supply and wiring of submain with two number 2.5 sq. mm frlsh pvc insulated 1100 v grade multistrand single core copper conductor cable. s.i. no 1301 ( b ) 148 , 25mm × 3mm g.i strip from earth electrode directly supply and laying of 25mm × 3mm g.i strip from earth electrode directly in the ground as required complete in all respect. s.i. no 716 , 1.5 sq. mm to 2.5 sq. mm cables, supply and fixing of crimping, solderless, copper tin electroplated lugs of dowells / ismail make suitable for 1.5 sq. mm to 2.5 sq. mm cables, including tapping with insulating tape, complete in all respect. s.i. no 1129 , pin type copper tin plated cable socket ( lug ) 16 sq. mm supply & fixing of plain or pin type copper tin plated cable socket ( lug ) 16 sq. mm to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the engineer incharge. s.i. no 504 ( d ) total quantity : 1...

North Central Railway - Uttar Pradesh

30331402 supply of surface mounting type analoguesurface mounting type analogue,surface mounting type analogue time switch 24 hrs daily driprate, 50 hz, 16 amp, 250 volt ac, clock wise rotation cat no. fm/7648 fi. make minilac, l&t, c&s. => limited...

Moradabad Municipal Corporation - Uttar Pradesh

30322294 line 03 civil lines chorahe se jigar colony chorahe tak decorative pole va light lagane ka karye line 03 civil lines chorahe se jigar colony chorahe tak decorative pole va light lagane ka karye , supplying, erection & testing of 8.0 mtr. ( 8000mm ) height decorative classic scarlett pole made of gi with inbuilt cast aluminum embellishments, pu painted copper black mixed colour, suitable for single drop down decorative led street light fittings including drop down fixture. the bottom portion ( 2000 mm long ) should be with 140 mm dia., 4.80 mm thick pipe and the medimum portion ( 4000 mm long ) with 114 mm dia., min. 3.8 mm thick pipe and top portion ( 2000 mm long ) with 90 mm dia., min. 3.0 mm thick pipe & should have arrangement to fixed ornamental brackets. the pole has a service window at the bottom comprising four way 25 amp. connector terminal and a mcb, the base plate of pole etc. as required, including fixing of pole, including foundation work as per site requirement cc 1:2:4 .adequate thickness and fastner, nut bolt. , supply and fixing decorative ornamental led street light drop down lumanaries duly powder coated / pu panted with pc with 120 w led streetlight, high lumen. color of led should be warm white, led light should be ip67 / 66, lm79 / 80, bis approved driver, led etc with completefive year warrenty / gurantee at site / store, including cost of labour, t&p etc complete. , supply and fixing ofone number 1.5 sq. mm. frlsh pvc insulated 1100 v grade multistrand copper conductor cable. , ( 1 ) for decorative poles , supply and laying of aluminium conductor pvc insulated armoured served sheathed cables 1100 volts. , ( j ) 25 sq. mm 3 1 / 2 core , supply and fixing following 25 a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn, complete in all respect. , supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the engineer incharge. , ( a ) 4 sq. mm , ( e ) 25 sq. mm , add l.cess @1% , add gst @ 12%...

Moradabad Municipal Corporation - Uttar Pradesh

30321694 line 02 mahila thane se dayanand degree college tiraha sbi bank hote huye deputy ganj chorahe tak decorative pole va light lagane ka karye line 02 mahila thane se dayanand degree college tiraha sbi bank hote huye deputy ganj chorahe tak decorative pole va light lagane ka karye , supplying, erection & testing of 8.0 mtr. ( 8000mm ) height decorative classic scarlett pole made of gi with inbuilt cast aluminum embellishments, pu painted copper black mixed colour, suitable for single drop down decorative led street light fittings including drop down fixture. the bottom portion ( 2000 mm long ) should be with 140 mm dia., 4.80 mm thick pipe and the medimum portion ( 4000 mm long ) with 114 mm dia., min. 3.8 mm thick pipe and top portion ( 2000 mm long ) with 90 mm dia., min. 3.0 mm thick pipe & should have arrangement to fixed ornamental brackets. the pole has a service window at the bottom comprising four way 25 amp. connector terminal and a mcb, the base plate of pole etc. as required, including fixing of pole, including foundation work as per site requirement cc 1:2:4 .adequate thickness and fastner, nut bolt. , supply and fixing decorative ornamental led street light drop down lumanaries duly powder coated / pu panted with pc with 120 w led streetlight, high lumen. color of led should be warm white, led light should be ip67 / 66, lm79 / 80, bis approved driver, led etc with completefive year warrenty / gurantee at site / store, including cost of labour, t&p etc complete. , supply and fixing ofone number 1.5 sq. mm. frlsh pvc insulated 1100 v grade multistrand copper conductor cable. , ( 1 ) for decorative poles , supply and laying of aluminium conductor pvc insulated armoured served sheathed cables 1100 volts. , ( j ) 25 sq. mm 3 1 / 2 core , supply and fixing following 25 a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn, complete in all respect. , supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the engineer incharge. , ( a ) 4 sq. mm , ( e ) 25 sq. mm , add l.cess @1% , add gst @ 12%...

Urban Development Department - Uttar Pradesh

30298579 bids are invited for pvc insulated armoured serbed sheated cables 1100 volt 10 sq x 2core supply and laying of aluminium conductor pvc insulated armoured serbed sheated cables 1100 volt 10 sq x 2core pwd si no. 50 , 75 to 90 watt led street light confirming to ip66 protection complete in all respect cat aaa supply and fixing of led street light fitting having die cast aluminium body and diffuser with driver set suitable for 75 to 90 watt. confirming to ip66 protection complete in all respect cat aaa pwd si 1423 , pvc insulated armoured serbed sheated cables 1100 volt 25 sq x 4core supply and laying of aluminium conductor pvc insulated armoured serbed sheathed cables 1100 volt 25 sq x 4 core pwd si no. 501j , time switch ts0 100 series with contractors hrc fuses isolation switch 40 amp supply and fixing of following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proofpint consisting of time switch ts0 100 serieswith contractors hrc fuses isolation switch 40 amp , painting of the clectric pole painting of the clectric pole with 2 coats of aluminium paint over red oxide primer complete in all respect pwd si no. 634 , safe earthing electrode t 39 length 200 mm supply and burring of safe earthing electrode t 39 ( hot dip galvanized ) length 200 mm pwd si no. 725 , d damp of 50 mm x 6mm flat iron on pole supply & fixing of d damp of 50 mm x 6 mm flat iron on pole pwd si no. 623 , 1.5 sq.mm frlsh pvc insulated multistrand single core copper wire wiring point for light with 1.5 sq.mm frlsh pvc insulated multistrand single core copper wire pwd si no. 121 c , distribution box for for pole distribution box for for pole. 4 no. aluminium bus bar 1 no 6amp. mcb with 1.5 meter gi pipe 50mm complete lug and glanded complete in aall respects. , 50mm gi pipe. supply of fixing 50mm gi pipe. total quantity : 1...

Northern Railway - Uttar Pradesh

30269402 supply of analogue time switch.analogue time switch.,analogue time switch with battery backup, din rail mounted, 3 p module, 24 hours programme, programmable every 30 minutes, backup o 100 hours, current capacity 16 amps, with one change over, aux supply 220/415 volts ac, to cat no. ta 926453 of indoasion. the time switch should be fitted in flameproof, weather proof, front opening, single door metallic/ poly carbonate enclosure of ip 54 rating normal size 150 mm x 150 mm x 120 mm with cable entry. make: l&t/ c&s/ havells or similar....

Municipal Corporation - Uttar Pradesh

30255514 naurangilal inter college to kathpula to agrasen chauraha supply and installation of pole with single arm bracket total height of the pole with single arm bracket shall be 6500 mm nominal above the ground. the pole is made out of mild steel tube in two steps. the dimensions of the bottom section of the pole is 140mm dia x 1500mm long 4mm thick and top section is 125 mm dia, 4000 mm long x 3mm thick 1 mtr long ornamental bracket. cast aluminium embellishments are fitted with the help of grub screws .a square mild steel base plate of dimension 250mm x 250mm x18mm thick shall be welded at the bottom of the pole with the stiffners. a built in service window is provided to accommodate a 6 amp sp mcb and 32 amp heavy duty connector for mains connections in the bottom part of the pole. the different sections of the pole are joined together by means of welded joints. the decorative bracket is made out of mild steel fabrication. the mild steel parts part are joined together & are fabricated to get the desired design. the height of the bracket shall be 1000mm. the decorative single arm bracket should have the arrangement to fix the required luminaire. the single arm bracket should have the arrangement suitable to be fitted on the required pole. the decorative pole and single arm bracket shall be machined and polished properly to give it a smooth surface. the decorative pole with single arm bracket is duly pretreated by shot blasting process and painted in u.v. ray resistant p.u. coating in approved color shade. fixing of pole with hillt super fixture compound resign with fastener screen. 2 supply and fixing of ornamental 180 watt led drop down luminaire aluminium housing powder coated pu paint with acrelic clear diffuser for light, dia = 510mm and height = 600mm and above having suitable heat sink and philips driver. on site maintenance with material withlabour for 05 year. 3 supply and laying of 25 sq. mm 3 1 / 2 core aluminium conductor pvc insulated armoured served sheathed cables 1100 volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. on surface the cable run shall be fixed on m.s. clamps etc. of suitable size or as directed by the engineer incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. ( sor 501 j ) 4 foundation of 500×500×1500 mmof rcc mixture of 1?2?3 ratio having 8 no. 12mm iron of height 1800mm and 8 number rings of 200×200×200 mm size of dia 8mm iron base, casted on site. or erection of pole on railway bridge with fastner and hillt super compound resin. 5 supply and burying of 40mm dia x 4.5 metres long g.i. pipe vertically for earthing having 12mm dia. holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of no. 6 to 8swg gi wire in g.i. pipe up to appron ( and from appron to switch board the cost of g.i. wire and pipe will be extra ) upto switch board, 30cm square c.i. box with hinged cover masonary enclosure, funnel at top, alternate layers of charcoal / coke and salt at least 150mm thick alround etc. as per directions of engineer in charge complete in all respects as per drawing. ( sor 701 ) 6 supply and fixing following capacity of25 a tpnautomatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn, complete in all respect. ( sor 807 e ) 7 hdpe 50m dia pipe ( market value ) 8 connector 9 s & f of 6 amp to 32 amp. spmcb ( 10 ka ) c curve 10 road cutting & re filling with bitumens of concrete and repair of divider damaged during work. 11 copper lugs for wire ends. 12 route marker stone 13 trench less drilling for cable laying...

Urban Development Department - Uttar Pradesh

30177631 bids are invited for pole s / f of steel tubular pole11.00 meter long designated 410, sp 51 with 450x450x1800mm, 1:3:6 cement concrete foundation including excavation back filling etc. comp. in all resp. , reflector s / f of factory wired integral led flood light luminaires with die cast aluminium housing built with driver set suitable for 150watt confirming to ip65 protection complete in all respect. , bracket s / f six arm bracket made of m.s. channel fixed in, rectanguler shape with nut & bolt with support of m.s.channel on 1mtr.long m.s. pipe sylender with having arrangement of06nos. led flood light fitting to give unifrom light on road surface comp. in all resp. as per specifitacion & desigen & drawing of e / i. , painting painting of electric pole with two coats of alu paint over red, oxide primer complete in all respects. , plinthing provision of plinthing of pole base dia 1.5mm circular around pole with4angle iron 1 mtr length outer circular fiilling 1:3:6 cement concrete foundation incl.12”x15” stone as per direction of e / i. comp. in all resp. , earthing supply and burring of safe earthing electrode t 19 ( hot dip galvanized ) , length up to 2000mm, outer pipe 50mm inner pipe 25, terminal dia12 mm, outer gi pipe of 16 swg and inner gi pipe of 12 swg with hot dip galvanization up to 100 micron filled with crystalline conductive mixture ( ccm ) having anti corrosive & conductive property with 50 kgs activated soil ( bfc ) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square c.i frame with hinged cover & masonry husing ( from electrode terminal to switch board, cost of 25x3 g.i strip will be extra ) , cable s / l of 10sq.mm.4core conductor pvc insulated armoured served sheathed cable 1100 v grade at depth of 750mm below ground level over a cushionof 75mm thick & arround and protected with burnt bricks on, protected with burnt bricks on side and on top onsurface., the cable run shall be fixed on m. s. clamps etc.of suitable size or as per direction of e / i. comp. in all resp. the armouring of the cable, shall be properly connected with the earth conductor by clamps etc., , pipe s / l of 2.5” pvc / hdpe pipe , automatic switch s / f 25 amp. tpn capacity of automatic street light cubical control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contractors hrc fuses isolating switch metering instrument & instrument box with cts etc. in case of tpn, complete in all respect. total quantity : 1...

Nagar Palika Nigam - Uttar Pradesh

30074757 bids are invited for supply and fixingof 12.5 mtr semi highmast at durga kund gate no. 4 pole with assessories s / f of 12.5 mtr. high mast shaft of approved make with rising system hot dip glavanized inside and outside dip, heaving pole sheet thickness 3 mm. top dia minimum 150mm, bottom dia 310 mm. base plate 25mm. thick suitable for wind velocity as per is 875 part 3 and having no circumferential weld, with accessories for high mast such as head frame / carriage ring suitable for 6 luminaries & its control gear boxes 0.75 hp power tool motor, 3 point suspension system with steel wire rope 6mm dia, double drum winch, including making suitable foundation as per manufacture drawing / site include reuiment along with foundation bolts nuts, washers, anchor plates etc. complete in all respect having 05 years warranty & guaranty with replacement as per engineer incharge. ( si no 651 year 2018 ) , led flood light with assessories s / f of factory wired integral led floold light luminaries with die cast aluminum housing and lenses built with mandatory driver sat suitable for200 watt. confirming to ip 66 protection. complete in all respect including labour. 05 years warranty & guaranty with replacement as per engineer incharge. ( si no 1455 year 2018 ) , earthing s / b of600mmx600mmx6mm gi plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia gi pipe and funnel for watering and one earthling lead of one no. 8 to 10 swg gi wire in 15 mm dia gi pipe up to switch board 30cm square ci frame with hinged cover masonry housing alternate layers of charcoal / coke and salt at least 150mm thick all round etc.as per directions of engineer in charge complete in all respect as per drowing ( this will apply for earthing of poles also ) . ( si no 702 year 2018 ) , control panel s / f of40a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn, complete in all respect. ( si no 807f ( ii ) year 2018 ) , cable wire s / l of 16sq mm x 4 core. aluminum conductor pvc insulated armouredserved sheathed cables 1100 volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and top. on surface the cable run shall be fixed on m.s. clamps etc. of suitable size of suitable size or as directed by the engineer incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. ( si no 501 ( i ) year 2018 ) , signaboard s / f of signboard of black granite stone for foundation stone / inauguration including writing in golden letters in all respects as per engineer in charge total quantity : 1...

Nagar Palika Nigam - Uttar Pradesh

30015682 bids are invited for supply and fixingof 12.5 mtr semi highmast atshivajee nagar udyan mahmoorganj pole with assessories s / f of 12.5 mtr. high mast shift of approved make with rising system hot dip glavanized inside and outside dip heaving pole sheet thickness 3 mm. top dia minium 150mm, bottom dia 310 mm., base plate 25mm. thick suitable for wind velocity as per is 875 part 3 and having no circumferential weld with accessories for high mast such as head frame suitable for 6 luminaries & its control gear boxes 0.75 hp power tool motor, 3 point suspension system with steel wire rope 6mm dia, double drum winch including making suitable foundation as per manufacture drawing / site include reuiment along with foundation bolts, nuts, washers, anchor plates etc. complete in all respect having 05 years warranty & guaranty with replacement as per engineer incharge. ( si no 651 year 2018 ) , led flood light with assessories s / f of factory wired integral led floold light luminaries with die cast aluminum housing and lenses built with mandatory driver sat suitable for200 watt. confirming to ip 66 protection. complete in all respect including labour. ( si no 1455 year 2018 ) , earthing s / b of600mmx600mmx6mm gi plate vertically for earthling with its top at least 3metres below ground level complete with 20mm dia gi pipe and funnel for watering and one earthling lead of one no. 8 to 10 swg gi wire in 15 mm dia gi pipe up to switch board 30cm square ci frame with hinged cover masonry housing alternate layers of charcoal / coke and salt at least 150mm thick all round etc. complete in all respect. ( si no 702 year 2018 ) , control panel s / f of40a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors hrc fuses, isolating switch metering instrument and instrument box with cts etc. in case of tpn, complete in all respect. ( si no 807f ( ii ) year 2018 ) , cable wire s / l aluminum conductor pvc insulated armored served sheathed cables 1100 volts rating 16sq mm x 4 core. complete in all respect. ( si no 501 ( i ) year 2018 ) , signaboard s / f of innaugration stone brighter gold letter including all complete total quantity : 1...

Nagar Palika Nigam - Uttar Pradesh

29963162 bids are invited for supply and fixingof 12.5 mtr semi highmast at ward 70 hustali ke kabrishtan pole with assessories s / f of 12.5 mtr. high mast shift of approved make with rising system hot dip glavanized inside and outside dip heaving pole sheet thickness 3 mm. top dia minium 150mm, bottom dia 310 mm., base plate 25mm. thick suitable for wind velocity as per is 875 part 3 and having no circumferential weld with accessories for high mast such as head frame suitable for 6 luminaries & its control gear boxes 0.75 hp power tool motor, 3 point suspension system with steel wire rope 6mm dia, double drum winch including making suitable foundation as per manufacture drawing / site include reuiment along with foundation bolts, nuts, washers, anchor plates etc. complete in all respect having 05 years warranty & guaranty with replacement as per engineer incharge. ( si no 651 year 2018 ) , led flood light with assessories s / f of factory wired integral led floold light luminaries with die cast aluminum housing and lenses built with mandatory driver sat suitable for200 watt. confirming to ip 66 protection. complete in all respect including labour. ( si no 1455 year 2018 ) , earthing s / b of600mmx600mmx6mm gi plate vertically for earthling with its top at least 3metres below ground level complete with 20mm dia gi pipe and funnel for watering and one earthling lead of one no. 8 to 10 swg gi wire in 15 mm dia gi pipe up to switch board 30cm square ci frame with hinged cover masonry housing alternate layers of charcoal / coke and salt at least 150mm thick all round etc. complete in all respect. ( si no 702 year 2018 ) , control panel s / f of40a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors hrc fuses, isolating switch metering instrument and instrument box with cts etc. in case of tpn, complete in all respect. ( si no 807f ( ii ) year 2018 ) , cable wire s / l aluminum conductor pvc insulated armored served sheathed cables 1100 volts rating 16sq mm x 4 core. complete in all respect. ( si no 501 ( i ) year 2018 ) , signaboard s / f of innaugration stone brighter gold letter including all complete total quantity : 1...

Nagar Palika Nigam - Uttar Pradesh

29961464 bids are invited for supply and fixingof 12.5 mtr semi highmast at pahadiya churaha and aktha tiraha pole with assessories s / f of 12.5 mtr. high mast shift of approved make with rising system hot dip glavanized inside and outside dip heaving pole sheet thickness 3 mm. top dia minium 150mm, bottom dia 310 mm., base plate 25mm. thick suitable for wind velocity as per is 875 part 3 and having no circumferential weld with accessories for high mast such as head frame suitable for 6 luminaries & its control gear boxes 0.75 hp power tool motor, 3 point suspension system with steel wire rope 6mm dia, double drum winch including making suitable foundation as per manufacture drawing / site include reuiment along with foundation bolts, nuts, washers, anchor plates etc. complete in all respect having 05 years warranty & guaranty with replacement as per engineer incharge. ( si no 651 year 2018 ) , led flood light with assessories s / f of factory wired integral led floold light luminaries with die cast aluminum housing and lenses built with mandatory driver sat suitable for200 watt. confirming to ip 66 protection. complete in all respect including labour. ( si no 1455 year 2018 ) , earthing s / b of600mmx600mmx6mm gi plate vertically for earthling with its top at least 3metres below ground level complete with 20mm dia gi pipe and funnel for watering and one earthling lead of one no. 8 to 10 swg gi wire in 15 mm dia gi pipe up to switch board 30cm square ci frame with hinged cover masonry housing alternate layers of charcoal / coke and salt at least 150mm thick all round etc. complete in all respect. ( si no 702 year 2018 ) , control panel s / f of40a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors hrc fuses, isolating switch metering instrument and instrument box with cts etc. in case of tpn, complete in all respect. ( si no 807f ( ii ) year 2018 ) , cable wire s / l aluminum conductor pvc insulated armored served sheathed cables 1100 volts rating 16sq mm x 4 core. complete in all respect. ( si no 501 ( i ) year 2018 ) , signaboard s / f of innaugration stone brighter gold letter including all complete total quantity : 1...

Nagar Palika Nigam - Uttar Pradesh

29961165 bids are invited for new led fitting street light at pandeypur awas vikas colony. s / f of new led fitting 75 to 90 watt for blank pole , aluminium conductor pvc insulator armoured10 sq. mm 4 core s / l of aluminium conductor pvc insulator armoured served sheathed cable 1100 volts grade at a depth of 750 mm below ground level over a cushin of 75 mm thick sand all around and protected with burnt bricks on sides and on top. on surface the cable run shall be fixed on m.s clamps etc. of suitable size or as directed by engineer. incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. 10 sq. mm 4 core , aluminium conductor pvc insulator armoured 16 sq. mm 4 core s / l of aluminium conductor pvc insulator armoured served sheathed cable 1100 volts grade at a depth of 750 mm below ground level over a cushin of 75 mm thick sand all around and protected with burnt bricks on sides and on top. on surface the cable run shall be fixed on m.s clamps etc. of suitable size or as directed by engineer. incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. 16 sq. mm 4 core , control panal s / f of 15 amp spn following capicity of automatic street light cubicle control panal painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contractors, hrc fuse, isolating switch metering instrument &instrument box withcts etc in case of tpn complete in all respects. , factory wired integral led flood light luminaires s / f of cat aaa factory wired integral led flood light luminaires with die cast aluminium housing built with driver set suitable for 170 to 200 watt. confirming to ip 66 protectiom completein all respects total quantity : 1...

Urban Development Department - Uttar Pradesh

29862862 bids are invited for pole s/f of steel tubular pole 09.00 meter long designated 410, sp 28 in 1:3:6 cement concrete foundation including excavation back filling etc. comp. in all respect. , led fitting s/f of led street light fitting having die cast aluminium body and diffuser with driver set suitable for 70watt confirming to ip66 complete in all respects , cable s/e of 16mm2 single core p.v.c. insulated al conductor cable. incl. fixing of 50x6mm flat iron d clamps & 75x90mm shackle insulator with nuts & bolts comp. in all resp. (span approx. 30m) , painting painting of electric pole with two coats of alu paint over red , oxide primer complete in all respects. , earthing supply and burring of safe earthing electrode t 19 (hot dip galvanized), length up to 2000mm, outer pipe 50mm inner pipe 25, terminal dia12 mm, outer gi pipe of 16 swg and inner gi pipe of 12 swg with hot dip galvanization up to 100 micron filled with crystalline conductive mixture (ccm) having anti corrosive & conductive property with 50 kgs activated soil (bfc) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square c.i frame with hinged cover & masonry husing (from electrode terminal to switch board, cost of 25x3 g.i strip will be extra) make: as approved in u.p. p.w.d., & c.p.r.i. certified. , automatic control panel s/f of 15 amp. spn automatic street light cubical control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contractors hrc fuses isolating switch metering instrument & instrument box with cts etc. in case of tpn, complete in all respect. total quantity : 1...

Urban Development Department - Uttar Pradesh

29819824 bids are invited for supply and fixing of 12.5mtr high mast shaft with 170w 200w led flood light luminaries with all supporting component / parts etc. each quantity contains –a ) supply and fixing of 12.5mtr high mast shaft of approved make with rising system hot dip galvanized inside & outside dip hearing pole sheet thickness 3 mm.top dia minimum 150mm, bottom dia 310mm base plate 25mm.– 01 nosb ) led flood light luminaries with die cast aluminum housing built with driver set suitable for 170 200 watt. – 08 nosc ) supply and fixing of led type double dome aviation obstruction light. – 01 nosd ) supply and laying of aluminum conductor pvc insulated armored served sheathed cables 1100 volts grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on sides and on top. on surface the cable run shall be fixed on m.s. clamps etc. – 100 mte ) supply and burning of safe earthing electrode t 39 ( hot dip galvanized ) length upto 3000mm outer pipe 76 mm inner dia 38mm terminal dia 12mm outer gl pipe of 16 swg and inner gl pipe of swg with hot dip galvanization upto loo micron filled with crystalline conductive mixture ( ccm ) having anti corrosive & conductive property with 50 kgs. – 04 nosf ) plain or pin type aluminum lug to the cable leads included with tape connecting etc. – 08 nosg ) s / l of 2.5s mm core copper cable under pole m.r. – 60 mth ) supply and fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch ts0 100 series with contractors and all etc. – 01 nos , numbering of pole with radium sticker numbering of pole by letter writing ( number named, agency ) with cost of radium sticker & t & p ( size 12x 48 ) ps no. quote total quantity : 1...

Urban Development Department - Uttar Pradesh

29796034 bids are invited for supply and fixing of 12.5mtr high mast shaft with 170w 200w led flood light luminaries with all supporting component / parts etc. each quantity contains –a ) supply and fixing of 12.5mtr high mast shaft of approved make with rising system hot dip galvanized inside & outside dip hearing pole sheet thickness 3 mm.top dia minimum 150mm, bottom dia 310mm base plate 25mm.– 01 nosb ) led flood light luminaries with die cast aluminum housing built with driver set suitable for 170 200 watt. – 08 nosc ) supply and fixing of led type double dome aviation obstruction light. – 01 nosd ) supply and laying of aluminum conductor pvc insulated armored served sheathed cables 1100 volts grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on sides and on top. on surface the cable run shall be fixed on m.s. clamps etc. – 100 mte ) supply and burning of safe earthing electrode t 39 ( hot dip galvanized ) length upto 3000mm outer pipe 76 mm inner dia 38mm terminal dia 12mm outer gl pipe of 16 swg and inner gl pipe of swg with hot dip galvanization upto loo micron filled with crystalline conductive mixture ( ccm ) having anti corrosive & conductive property with 50 kgs. – 04 nosf ) plain or pin type aluminum lug to the cable leads included with tape connecting etc. – 01 nosg ) s / l of 2.5s mm core copper cable under pole m.r. – 60 mth ) supply and fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch ts0 100 series with contractors and all etc. – 01 nos , numbering of pole with radium sticker numbering of pole by letter writing ( number named, agency ) with cost of radium sticker & t & p ( size 12x 48 ) ps no. quote total quantity : 1...

Urban Development Department - Uttar Pradesh

29778376 bids are invited for high mast complete supply & fixing of 16 mtr high mast shaft of approved make with rising system hot dip glavanized inside & out side dip, heaving pole sheet thickness 3 mm. top dia minium 150 mm, bottom dia 360 mmbase plate 32 mm thick suitable for wind velocity as per is 875 part 3 &having no circumferential weld, with accessories for high mast such as head frame suitable for 6 to 12 luminaries & its control gear boxes 1.5 hp power tool moter, 3 point suspension system with steel wire rope 6 mm dia, double drum winch, including making suitable foundation as per manufature drawing / site reuiment along with foundation bolts nuts, washers, anchor plates etc complete in all respect. ( pwd s.i. no. 652 / 2018 ) , led lights supply and fixing offactory wired integral led flood light luminaires with die cast aluminium housing built with dirver set suitable for 170 to 200 watt. confirming to ip 66 protection complete in all respect and high power led with lenses, > 110lm / w, pf>0.95, thd<10% at full load, cri>70, potted driver set ( not circuitory ) , phase to phase protection at 440 v & > 300v auto cut and re start feature, with 5 year warranty.pwd sor 1455 , high mast aviation light supply of led type single dome aviation obstruction light. pwd sor 409 , earthing supply and burring of safe earthing electrode t 39 cu copper coated, length up to 3000mm, outer pipe 76.3mm x 3.2 inner pipe 42.4mm x 2.6mm, terminal dia 12mm, coating 80 100 micron filled with crystalline conductive mixture ( ccm ) having anti corrosive & conductive property with 50 kgs activated soil ( bfc ) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square c.i. frame with hinged cover & masonry housing. ( from electrode terminal to switch board, cost of 25 x 3 copper strip will be extra ) . make: as approved in u.p. p.w.d., & c.p.r.i. certified. ( s.i. no. 726d / 2018 ) , control panel supply and fixing of 63 amp. tpn of of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn, for the automatic switching of luminaries, power tool control with 2 no 9a contactors and raise lower push button, complete in all respect. m.r. , cable s / l of “al” conductor pvc insulated armoured, served, sheathed cable 1100 volts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround & protected with burnt bricks on sides & on top. on surface the cable run shall be fixed on ms clamps etc. of suitable size or as directed by the e / i, comp. in all resp. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. 50mm sq. mm 3.5 core.pwd sor 501 ( l ) , gi strip supply and laying of 32 mm x 6 mm g.i. strip from earth electrode directly in the ground as required complete in all respect. ( s.i. no. 717 / 2018 ) , dwc pipe supplying and laying of 120 mm dia. ( od 120 mm & id 103 mm nominal ) dwc hdpe pipe isi marked along with all accessories like socket, bend, couplers etc. conforming to is 14930, part ii complete with fitting and cutting, jointing etc. direct in ground ( 75 cm below ground level ) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. ( dsr no. 14.16.3 / 2018 ) ( 341 12% gst = 300.08 ) , lug supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the engineer incharge. 16 sq. mm pwd sor 504 ( d ) total quantity : 1...

Nagar Palika Nigam - Uttar Pradesh

29758291 bids are invited for 1 supply and fixing of 12.5 mtr semi highmast at imiliya ghat and vaurna vihar colony . pole with assessories s / f of 12.5 mtr. high mast shift of approved make with rising system hot dip glavanized inside and outside dip heaving pole sheet thickness 3 mm. top dia minium 150mm, bottom dia 310 mm., base plate 25mm. thick suitable for wind velocity as per is 875 part 3 and having no circumferential weld with accessories for high mast such as head frame suitable for 6 luminaries & its control gear boxes 0.75 hp power tool motor, 3 point suspension system with steel wire rope 6mm dia, double drum winch including making suitable foundation as per manufacture drawing / site include reuiment along with foundation bolts, nuts, washers, anchor plates etc. complete in all respect having 05 years warranty & guaranty with replacement as per engineer incharge. ( si no 651 year 2018 ) 2 led flood light with assessories s / f of factory wired integral led floold light luminaries with die cast aluminum housing and lenses built with mandatory driver sat suitable for 200 watt. confirming to ip 66 protection. complete in all respect including labour. ( si no 1455 year 2018 ) 3 earthing s / b of 600mmx600mmx6mm gi plate vertically for earthling with its top at least 3metres below ground level complete with 20mm dia gi pipe and funnel for watering and one earthling lead of one no. 8 to 10 swg gi wire in 15 mm dia gi pipe up to switch board 30cm square ci frame with hinged cover masonry housing alternate layers of charcoal / coke and salt at least 150mm thick all round etc. complete in all respect. ( si no 702 year 2018 ) 4 control panel s / f of 40a tpn capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors hrc fuses, isolating switch metering instrument and instrument box with cts etc. in case of tpn, complete in all respect. ( si no 807f ( ii ) year 2018 ) 5 cable wire s / l aluminum conductor pvc insulated armored served sheathed cables 1100 volts rating 16sq mm x 4 core. complete in all respect. ( si no 501 ( i ) year 2018 ) 6 signaboard s / f of innaugration stone brighter gold letter including all complete...

Urban Development Department - Uttar Pradesh

29737385 bids are invited for supply & fixing 1 supply & fixing of 8 mtr gi octagonal pole of approved make ( top dia 70mm, bottom dia 13mm and base plate 12mm thik ) having 3mm thickness with double arm bracket according to departmental design ( 1 mtr length ) on rcc foundation including th cost of foundation, foundations bolts, excavation & back filling and required t&p comlete in all respect pwd sor 2017 18 s.n 644 , supply & fixing of factory supply & fixing of factory wired integral led street light luminaries with die cast aluminium housing built with driver set suitable for 175 200 watt confirming to ip 66 protection complete in all respect cat aaa pwd sor 2017 18 s.n 1425 , dismatling of cc road dismatling of cc road sureface for laying of alluminimum conductor including shorting out of servesabile material and disspossel of unservesable metarial up to a distance of 50 mtr including supply of all labour t&p etc complete ( 450×0.6×0.15=40.5 ) , excavation of earth excavation of earth for aluminium coductor bulb work in soil mixed with moorum, kankar and shinjle etc including lift upto 1.5 mtr and lead upto 50 mtr and refiling watering and remming of exca or laying of pipe line withed earth into trench and disposel of serpulse earth of upto 50 mtr from th e center of the foundation trench ( 450×0.6×0.5=135 ) , supply & laying supply & laying of 16sq mm 4 core aluminium coductor pvc insulated armoured served sheathed cables 1100 volts grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burn bricks on sides and on top.on surface the cable run shall be fixed on m.s clamps etc of suitable size or as directed by the engineer incharge, complete in all respect.the armouring of the cable shall be properly connected with the earth conductor by clamps etc. pwd sor 2017 18 s.n 501 ( b ) , reinstatement of the cc reinstatement of the cc road by watring, ramming & consolidation of the trenches complete including all metarial, labour t&p etc complete as per required. ( 450×0.6×0.15=40.5 ) , supply & laying of following size dwc hdep pipe supply & laying of following size dwc hdep pipe isi mark along with all accessories like socket bend cuppler etc comfirming to is 14930 part second complete with fitting and cutting joining etc direct in ground ( a suitable desk below brown level ) etc complete as recuire 63 mm dia. , supply & fixing 2 supply & fixing of ( 450×450 ) mm size redium reflective sign board of nagar panchayat all complete as per direction , supply & laying of following supply & laying of followingsize capacity of aoutomatic street light cubicle control panel painted with anti corossive alkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering instrument & instrument box with cts etc.in case of tpn, complete in all respect.pwd sor 2017 18 s.n 807 ( c ) , supply & buring supply & buring of safe earthing electrode t 19, ( hot dip galvanized ) , length up to 3000 mm, outer dia 50 mm inner dia 25 mm, terminal dia 12 mm, outer gi pipe of 16 swg and inner gi pipe of 12 swg with hot dip galvanization up to 100 micron filled with srystalline conductor mixture ( c.c.m ) having inti corossive & conductive property with 50 kgs activated soid ( b.f.c ) capable of reducing the soil resistivity with good mixture of retaining capacity and one earthing lead of 25 mm× 3mm g.i strip , upto switch board ( from apron to switch board, the cost of g.i strip will be extra ) along with 30 cm square c.i frame with hinged cover & masonry housing.make: as approved in u.p.p.w.d & c.p.r.i certified. , providing and fixing ( 25×3 ) providing and fixing ( 25×3 ) mm gi strip in 40 mm dia gi pipe from earth electrode including connection with gi nut bolt spring warsher excavation and refillink etc as required. , supply and fixing 6mm supply and fixing 6mm 2crore all conductor pvc cable for light connections ( ps s.n. 501a ) total quantity : 1...

Urban Development Department - Uttar Pradesh

29582233 bids are invited for ( a ) 16sq.mm.4core s / l of alu conductor pvc insulated armoured served sheathed cable 1100 v grade at depth of 750mm below ground level over a cushionof 75mm thick & arround and protected with burnt bricks on, protected with burnt bricks on side and on top onsurface., the cable run shall be fixed on m. s. clamps etc.of suitable size or as per direction of e / i. comp. in all resp. the armouring of the cable, shall be properly connected with the earth conductor by clamps etc. , ( b ) 35sq.mm.3 1 / 2core ( b ) 35sq.mm.3 1 / 2core , gi pipe s / f of 1.50mtr long 50mm dia g.i pipe ( class b ) bracket with 120deg angle on 1.0m height fixing on rcc bridge pilor wall including s / fixing of suitable plate & six nos fastener, nuts & bolts etc comp in all resp as per dir by e / i. , earthing boring supply and burring of safe earthing electrode t 19 ( hot dip galvanized ) , length up to 2000mm, outer pipe 50mm inner pipe 25, terminal dia12 mm, outer gi pipe of 16 swg and inner gi pipe of 12 swg with hot dip galvanization up to 100 micron filled with crystalline conductive mixture ( ccm ) having anti corrosive & conductive property with 50 kgs activated soil ( bfc ) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square c.i frame with hinged cover & masonry husing ( from electrode terminal to switch board, cost of 25x3 g.i strip will be extra ) make: as approved in u.p. p.w.d., & c.p.r.i. certified. , junction box s / f of sintex smc junction box ( 300x200x100mm ) with channel, cable connector, fixing on wall with fastener with m / s clamp nut bolts etc.as per dir by e / i. , pipe s / f 1 pvc flexible pipe on wall with bend & strip with fixing of rcc wall with fastener etc. as per dir by e / i. , lug s / f of35sq.mm plain or pin type capper tin plated cable socket ( lug ) to the cable leads, insulating with top quality tape pvc and making all connection etc. comp. in all resp. as per direction of e / ic. , 35 sqmm lugs s / f of 35sq.mm.3 1 / 2core brass nickle plated compression gland for pvc insulated & armoured served sheathed, underground cable including rubber fing etc. complete in all respect. the armouring of the cable shall be properly connected with the earth as per direction of e / i. , bracket making connection of each double arm street lightpillerin box backelite sheet suitable size 4 no. of10amp. mcb, lug andhavey duty connector by 1.5sq.mm 3 core copper flexible cable ( 20mtr app ) from fitting. to d.b comp. in all resp. as ins.by e / i , hdpe pipe s / l of 4” pvc / hdpe pipe with fixing of rcc wall with fastener & nut bolts at every meter or side required as per direction of e / i. , road cutting provision of road cutting & repairing the same as per side requirement or as per dir by e / i. , tpn box s / f of 40a tpn following capacity of automatic street light cubicle control panel painted with anti corrosive slkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn complete in all respect.as per dir by e / i. , boring boring of the earth across the road at the depth of 3 4mtr. be low from the ground level incl. dip hdpe pipe with end cops.as per dir by e / i. , labour labour work using of tower / ladder / hydra, drilling machine & genset etc as per side requied as per dir by e / i. total quantity : 1...

Urban Development Department - Uttar Pradesh

29577668 bids are invited for post lantern s / fdecorative 8 to 15 watt led bollard luminaire with driver set confirming to ip 65protectioncomp.in all resp. ( s.i no 1442 ) , cable s / l of 10sq.mm.4core conductor pvc insulated armoured served sheathed cable 1100 v grade at depth of 750mm below ground level over a cushionof 75mm thick & arround and protected with burnt bricks on, protected with burnt bricks on side and on top onsurface., the cable run shall be fixed on m. s. clamps etc.of suitable size or as per direction of e / i. comp. in all resp. the armouring of the cable, shall be properly connected with the earth conductor by clamps etc., , pipe s / l of 2.5” pvc / hdpe pipe , automatic switch s / f 25 amp. tpn capacity of automatic street light cubical control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contractors hrc fuses isolating switch metering instrument & instrument box with cts etc. in case of tpn, complete in all respect. total quantity : 1...