Development Authority - Uttar Pradesh

34091186 supply of brick, brick ballast, interlocking brick, sand, cement, gravel, rod, paint, wiring, tiles, cartridge, plumber, cement chair, rod, aluminium, steel door, plastic fiber net, green frame, wooden furniture, bench, chair, maze, stool glass board, solar light, street light, door, windows, hume pipe....

Canal Division - Uttar Pradesh

33902687 construction of switch room, r.c.c. foundation. earth work. cement concrete road work. brick work. providing of steel bar. providing and fitting of steel doors, window. cement plaster work. painting of switch room. fixing of r.c.c. outlet pipe. brick work. mechanical work. dismantling of old ms pipeline. painting of ms pipeline....

Indo Tibetan Border Police - Uttar Pradesh

33548305 bids are invited for stainless steel butt hinges of length 100mm , stainless steel butt hinges of length 125mm , stainless steel door stopper of standard size , aluminium tower bolt of length 100mm , aluminium door handle of size 150mm , aluminium door handle of size 125mm , hydraulic door closer , sliding door bolt of size 300mm , tarelt roll bitumen , synthetic enamel paint , tarpentine oil , green paint for roof , red oxide primer , jumper washer light duty , jumper washer heavy duty , c.p waste coupling 32mm , c.p health faucet hand shower , cp spindle heavy duty , cp towel rail , c.p toilet paper stand , c.p soap stand , g.i union of size 20mm dia , g.i union of size 25mm dia , g.i union of size 32mm dia , g.i tee of size 15mm dia , g.i tee of size 20mm dia , g.i tee of size 25mm dia , gi socket of size 15 mm dia , gi socket of size 20mm dia , gi socket of size 25mm dia , g.i elbow of size 15mm dia , g.i elbow of size 20mm dia , g.i elbow of size 25mm dia , g.i plug of size 15mm dia , g.i plug of size 20mm dia , g.i plug 25mm , g.i plug 32mm , g.i reducer socket of size 25mmx20mm , g.i reducer socket of size 25mmx32mm , glass putty , looking mirror of size 600x450mm , glass shelf of size 600x120x5 mm with cp brackets , iron nails mix , oil bounded distemper , white cement , pvc low level cistern 10ltr capacity , pvc flushing cistern kit , hdpe water tank 500ltr of not less than 3 layers , plain float glass 4mm thick , ply board 6mm , ply board 12mm , safeda , plumber thread , m sel of 100gm pkt , vitreous china flat back wash basin of size 630x450 mm , wire mesh stain less steel of wire diameter 0.7mm and aperture 4.5mm , star screw 20mm of 1000nos per pkt , star screw 25mm of 1000nos per pkt , star screw 32mm of 1000nos per pkt , star screw 40mm of 1000nos per pkt , pozzolana portland cement of 50kg , adhesive for wood , wall putty , pvc pipe of 4inch dia and 3m length , pvc bend 4 inch dia , cgi sheet 3 inch x 10 inch of minimum thickness 0.5mm , paint brush of size 3 inch , paint brush of size 4 inch , roler painting of size 4 inch , iron putty blades 4 inch x 4 inch , self screw 1.5inch , self screw 2 inch , self screw 2.5 inch , self screw 3 inch , pvc tank cover for 500ltr tank of standard size , pvc tank covern for 750 1000ltr tank of standard size , cement fibre sheet for ceiling of size 2 inch x2 inch...

Urban Development Department - Uttar Pradesh

33500043 provide of construction material brick, gitty, interlocking, balu, cement, morang, rod, paint, wiring, stone, tiles, cartridge, ro, atm, flower, plumber, cement bench, iron, aluminum, steel door, plastic fiber jali, grill, frame, wood, furniture bench, chair, table, stool, solar light, street light, door, window, hume pipe....

East Central Railway - Uttar Pradesh

33483734 auction sale of scrap misc. items ferrous(1)local lot no 2507202201,unserviceable scrap boxn door (mild steel),200nos,12mt(2)local lot no 2507202202, unserviceable scrap stainless steel door(hl),200nos, 13.20mt(1 2)location near dry office right side of pathway(3)local lot no 2507202204, unserviceable scrap knuckle,50nos, 1.75mt(4)local lot no 2507202205, unserviceable scrap adaptor(narrow jaw), 500nos, 5.875mt(5)local lot no 2507202206,unserviceable scrap bolster spring(broken), 1.0mt(6)local lot no 2507202207, misc scrap,10mt(3 6)near dry office...

Department Of Urban Development - Uttar Pradesh

33384029 provide of construction material brick, gitty, interlocking, balu, cement, morang, rod, paint, wiring, stone, tiles, cartridge, ro, atm, flower, plumber, cement bench, iron, aluminum, steel door, plastic fiber jali, grill, frame, wood, furniture bench, chair, table, stool, solar light, street light, door, window, hume pipe....

Development Authority - Uttar Pradesh

33336584 tender for supply of brick first class, interlocking brick, sand, cement, morang, rod, paint, wiring, stone tiles, stone ballast, cartage, r. o.atm, flowers, flower petal, plumber, cement bench, aluminum, iron, steel door, plastic fiber jar, jungla, grill, frame wod, furniture bench, chair, mess, stool, glass board, solar light, door, hum pipe etc. materials....

Uttar Pradesh Housing And Development Board - Uttar Pradesh

33143736 construction of remaining work at p.h.c., kapsad, meerut. 1 excavation in foundation in ordinary soil ( loan clay ot sand ) including lift upto 1 50 meters and lead upto 30 mitr. including filling watering and tranming of excavated earth in the trenches of the building between the building and the sides of foundati trenches or in the plinth and extraction of disposal; as directed by the engineer incharge, the foundation trenches from 30m ( including royality ) 2 fillingof carted earth incide the plinth including cartage from a distance not less than 8 kms also including levelling dressing watering & ramming complete & cost of earth & royality etc. 3 sand filling in plinth including supply of necessary quantity of sand from a distance not excluding 8km from the site of work and including watering dressing etc. rate to include cost of all materials, labour and t&p etc.required for proper completion of the work. 4 providing and layingin cement concrete 1:4:8 ( 1 cement :4 coarse sand :8stone ballast 40 mm nominal size ) and curing complete, including cost ofform work, in foundation and floors complete including cost of all materials, labour and t&p etc.required for proper completion of the work. 5 cement concrete 1:1.5:3 ( 1 cement : 1.5coarse sand : 3 graded stone aggregate 20 mm nominal size ) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete. 6 providing and laying in position bitumen hot sealing compound for expansion joints etc. dsr 16.46.1using grade a sealing compound. 7 contruction of apron drain ( 150*150 mm size, for 1.00m. length ) 8 providing and injecting chemical emulsion for constructional antitermite treatment and creating a chemical barrier under and alround the column pits. wall trenches basement excavation top surface of plinth fillingjunction wall and floor along the external perimeter of binding expansion joints, surrounding of pipes and conduit etc complete ( plinth area of building at ground floor only, shall be measured as per 6313 ( part ii 1981 ) excluding gst. aldrine emulsifiable concen trate any other approved material such as heptrachlor or chlordance will be used. the rate of application of chemical emulsion shall be as follows: ( 1 ) treatment for masonry 8 foundation 5 liters per sqm. ( 2 ) , back fill in immediate contact with foundation 7.50 liters per sqm. ( 3 ) treatment of top surface of plinth fillings 5 ??liters / sqm. ( 4 ) .treatment ofsoil along external perimeter of building 7.50 liters / sqm. ( 5 ) . treatment of soil under apron along with external perimeter 5 liters / sqm. 9 first class brick work in 1:4 cement and coarse sand ( fm 1.50 to 2.20 ) mortar infoundation & plinth including supply of all materials, labour and t & p etc. 10 first class / class 150 brick work in1:6cement and coarsesand ( fm 1.50 to 2.20 ) mortar in foundation and plinth including supply of all materials, labour and tools and plants etc. required for propercompletion of the work. 11 r.c.c. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 bwg binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than m 20. 12 same as in above item but for slabs ( using 1:1.5:3 mix concrete ) 13 same as in above item but for the lighterbeams i.e. having spans upto 6 m. ( using 1:1.5:3 mix concrete ) 14 same as in above item but for footing ( using 1:1.5:3 mix concrete ) 15 same as in above item but for column ( using 1:1.5:3 mix concrete ) 16 cast cement concrete door sills, chaukhats, boundary posts shelves and similar small work with cement, approvedcoarse sand and 2 cm gauge stone grit in proportions of 1:2:4 excluding its fixing and binding the same with 24 b.w. g.g.i., binding wire, moulds, all materials labour, tools & plants etc. required for proper completion of the work. the rateexcludes making of drip course which shall be paid extra. 17 first class / class 150 brick work in1:6cement and coarsesand ( fm 1.50 to 2.20 ) mortar in super structureincluding necessary cutting and moulding of brick work as required and also includinghoney combed brick work in thickness of wall more than 12cms.including supply ofall materials, labourand tools and plants etc. requiredforpropercompletion of the work. 18 first class / class 150 brick work in1:4cement and coarsesand ( fm 1.50 to 2.20 ) mortar in super structureincluding necessarycutting and mouldingofbrickworkas required andalsoincludinghoney combed brick work in wall thickness 12 cms & below..including supply ofall materials, labourand tools and plants etc. requiredforpropercompletion of the work. 19 painting on d.p.c. with two coats of air blown bitumen vg 10 grade @ 1.70 kg / sqm approximate including cost of fuel if any. 20 providing and laying brick koba 12 mm thick laid with m 150 class brick bat coba 7.50 cm thick with gap of 15 mm to each other over 20 mm thick base of cement mortar 1:4 cement and course sand mixed with water proofing compound preading cement slurry mixed with aereclic cement concrete water proofing compound filled gaps of coba & top of coba mortar finished smooth & top mashed false square 30 cm xcm and side wall parapet shall be mono tythic plaster wall upto 30 cm higher and junction and corner shall be rounded by brick ballast and course sand masonary coba with top finshed plaster mixed with acetic water proofing compound @ 2% by weight & including s / o all material, labour, t&p etc complete for proper comletion of the work. 21 supply and fixingof flushdoors commercialqualityconformingtoi.s.2202 part i ( 1983 ) includingfixingof wooden cleats and stoppers and including fixing and adjustment of hinges, bolts, locks, handle, springs and other fitting with necessary screws complete. 35 mm thick 22 mild steel or iron workofsmall sizes and sections suchand holding down bolts, holdfasttierods, gratings etc. ( when notincludedinan overall rates ) wroughttorequiredfromincluding supply ofsteel anditswastage includingcostof bolts, nuts if required forandwelding, grinding and making holes as required completion of workfabricationofholesdoors, chaukhats nosing. ( a ) fabrication of holdfast & door chaukhat. 23 ( b ) same as in above item but for fabrication of grill / stairscase railing / gate. 24 ( c ) same as in above item but for fabrication of z section steel windows.openable 25 providing and fixing fly proof galvanized m.s. wire gaugeto windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete with 12 mm mild steel u beading 26 providing and fixing wire gauge shutters using galvanized m.s. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :35 mm thick shutters with isi marked m.s. pressed butt hinges bright finished of required size kiln seasoned and chemically treated hollock wood 27 supply and fixing of 24 guage aluminium sheet on toilet door shutters bottom including fixing with aluminium greves, labour including labour t&p etc required for proper completion of the work 28 mild steel or iron in plain work such as rcc or r.b. work wrought to required shape as necessary including bending for proper competition of the work and including supply of all steel & wastage and over lapping and hooks. 29 fixingofsteelorwoodenchaukhats in position. ( a ) door chaukhats window chaukhats above 1.5 sqm. and upto 3.0 sqm. 30 ( b ) same as in above item but for window chaukhats up to 1.5 sqm 31 ( c ) same as in above item but for ventilator chaukhats 32 12mm thick plaster with 1 cement : 6 course sand over brick work, minimum thickness not to be less than 3 / 8 ( 10mm ) thick including supply of all materials, labour and tools and plants etc required for completion of the work. 33 12 mm cement plaster on rough side with 1 cement : 6 course sandover brick work, minimum thickness not to be less than 3 / 8 ( 10mm ) thick including supply of all materials, labour and tools and plants etc required for completion of the work. 34 12 mm bearing plaster 1 cement:6 coarsesand 35 making grooves 10 to 12 mm wide x 8 mm deep in plaster of the wall or in celling vertically or horizontally as required. 36 making drip course in sun shade facia as per direction of engineering charge including supply of all material labour etc. required for proper completion of the work. 37 supply and fixing 6 mm ( 1 / 4 ) thick china white glazedtiles inflooringorin skirting or dado laid with1:3 cement and approved coarse sand mortar finished with whitecement slurry jointing and polishing complete includingsupplyof allmaterials, labour and tool sand plantsetc.required forproper completion of the work. excluding gst. 38 2.5 cm thick 1:2:4 plain cement concretefloor with cement approved coarse sand and 2cm. graded approved stone ballast laid in planels finished with 3mm ( 1 / 8 ) floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified over and including 8 cm. ( 3 ) local sand and brick ballast 4 cm. gause in proportion of 1:4:8 and removing any giving then a uniform finish, including supply of all materials, labour, t&p etc. required for proper completion of the work. but without base concrete. 39 cement concrete flooring 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size ) laid in one layer finished with a floating coats neat cement ( 40 mm thickfloor ) . 40 2 cm. ( 3 / 4 ) thick cement plaster in dedo or skirting in 1:2 consisting of one part of cement and 2 parts of approved coarse sand laid in pannels, finished with 3 mm ( 1 / 8 ) floating coat of neat cement or cement and marble dust in ratio of 5 1 including supply of all materials labour and t & p etc. required proper completion of the work 41 providing and laying 25 mm kota stone flooring over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid over jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete. 42 providing& laying of vitrified tiles of 600 mm x 600 mm size ( thickness 10 mm ) with water absorption less than .08% and conforming to is: 15622, of approved brand & manufacturer, in desired colours and shades, laid with cement based high polymer modified quick set tile adhesive ( water based ) conforming to is15477 including grouting of joints. 43 18 mm thick marble tiles in rises of step skirting dado wall and pillars laid on 10mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) jointed with gray cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete. 44 painting or varnishing work in small areas or new wood work with one coat ( upto one sqm of ready mixed priming paint and one coat of approved superior quality ready mixed paint or varnish including supply of all materials, labour toolsandplants etc. required forpropercompletion of the work. piant to be used isi marked. ( for two coat ) 45 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade :new work ( two or more coats applied @ 1.43 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm ) ( apex ultima, weather coat all guard ) assian, berger. 46 finishingwallswith water proofing on cementpaint of approvedmakesuch as super snowcem, durrocem, robiacem, guttucem supercem qualityandof required shade on undecorated wall surfaces ( two coat ) overone andincludingonecoatwhite cementprimertogiveaneven shade after thoroughly brushing the surface to powdered materialsincluding curing and cost of all materials. 47 one priming coat and one coat oil distemper on new work incliding supply of all materials, labour and t&p required for proper completion of the work ( for two coat ) 48 finishing wall with acrylic emulsion paint of approved brand and manufacture and of required shade and undecorated wall surface to give an even shade over including curing and cost of all material, labour, t&p etc. required for proper completion of the work for two coat. 49 providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : with 4.0 mm thick glass panes. 50 providing and fixing glass strips in joints of terrazo / cement concrete floors. 51 providing stainless steelsliding bolts16 mm dia with nuts and 250 mm long. 52 providingstainless steel towerboltwith10 mmdia and screw.300 mm long 53 providing and fixing stainless steel handle with screws etc. complete ( a ) 150 mm 54 providing and fixing oxidised sliding door bolts isi marked anodisedwith nuts and screws etc. complete : 300x16 mm 55 providing and fixing oxidised tower bolts isi marked anodisedwith necessary screws etc. complete :250x10 mm 56 providing and fixing oxidised handles isi marked anodisedwith necessary screws etc. complete : 100 mm 57 providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of t iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer 58 providing and laying 80mm thick factory madeinter locking c.c. paver block of m 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer in charge. 59 water supply and sanitary : providing and fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with isi marked white solid plastic seat and lid, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) , conforming to is : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. 60 providing and fixing water closet squatting pan ( indian type w.c. pan ) with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) conforming to is : 7231, with all fitting and fixtures completed including cutting and making good the walls and floors wherever required.white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests. 61 providing & fixing white viterous china wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standardpattern, including painting of fitting and brackets, cutting & making good the walls wherever required. flat back wash basin size 550x400 mm with single 15mm c. p. brass pillar tap 62 providing and fixing flexible p.v.c. waste pipe for sink or wash basin including pvc waste fittings complete.32 mm dia ( for wash basin ) 63 same as in above item but for 40 mm dia ( for sink and urinal ) 64 providing & fixing 600 x 450 mm bevelled edge mirror of superiorglass ( of approved quality ) complete with 6mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. 65 providing & fixing stainless steel a isi 304 ( 18 / 8 ) kitchen sink as per is:13983 with c.i. bracketsandstainless steel plug 40 mm including painting of fittings and brackets cutting and making good the walls wherever required. 610 x 460 bowl depth 200 mm 66 s / f of upvc swr pipe type b confirming to is 13592 incluiding jointing the pipes with rubber ring lubricant and upvc swr cuplar confirming to is 14735 also inluiding excavation of treches cutting of walls and holes and repairing of walls , floors and refilling the trenches as before cut including cost of other fittings such as door band, t and yt including supply of all materials labour and t&p required for prper complition of the work.110mm dia swr pipe 67 same as above item but for 90mm dia swr pipe 68 same as above item but for 160mm dia swr pipe 69 s / f of upvc swr nahani trap size100 / 90mm confirming to is 14735 self cleaning design fixed in pcc 1:2:4 and supply and fixing of 125 mm dia heavy duty cp brass jali. 70 laying cement concre 1:5:10 in haunching s.w. pipes including concrete for bedding necessary form work and during complete.100 mm dia 71 same as above item but for 150mm dia 72 s / f of upvc swr cowel confirming to is 14735 110 mm 73 providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 74 providing and fixing of chlorinated polyvinyle chloride ( cpvc ) pipes, having thermal stability for hot and cold water supply, including all cpvc plain and brass threaded fittings, inluding fixing the pipe with clamps at 1 m. spacing . this includes jointing of pipes and fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. internal work exposed on wall.25mm dia nominal bore 75 same as in above item but for 32mm dia nominal bore 76 providing and fixing of chlorinated polyvinyle chloride ( cpvc ) pipes, having thermal stability for hot and cold water supply, including all cpvc plain and brass threaded fittings, inluding fixing the pipe with clamps at 1 m. spacing . this includes jointing of pipes and fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. concealed work including cutting chases and making good the wall etc.20mm dia nominal bore 77 same as in above item but for 25mm dia nominal bore 78 providing and fixing of chlorinated polyvinyle chloride ( cpvc ) pipes, having thermal stability for hot and cold water supply, including all cpvc plain and brass threaded fittings. this includes jointing of pipes and fittings with one step cpvc solvent cement, trenching , reifilling and testing of joints complete as per engineer in charge. external work.25mm dia nominal bore 79 same as in above item but for 32mm dia nominal bore 80 providing & fixing gun metal gate valve with c.i. wheel of approvedquality ( screwed end ) 25 mm nominal bore 81 providing and fixing ballvalve ( brass ) of approved quality complete. ( high or low pressure with plastic floats ) .15 mm nominal bore 82 providing&fixing15 mm nominal bore45 cm long unplasticised pvc connection pipewith brass unions. 83 providing & fixing 15 mm nominal bore cp brass bib cockof approved quality conformingtois 8931. 84 providing and fixing 15 mm nominal bore c.p brass long nose bib cock of approved qualityconforming to is standardsandweighing notlessthan 810 gms. 85 providing & fixing 15 mm nominal bore c.p. brassstop cock ( concealed ) of standard designandof approvedmakeconforming to is : 8931. 86 providing & fixing 15 mm nominal bore c.p brass angle valve for basin mixer and geyser points of approved quality conformingto is8931. 87 providing & fixing 100 mm dia c.p brass shower rose with 15mm inlet. 88 suppling and hoisting of sintex or equivalent high density polythylene seamless of piece moulded tanks and placing the same in proper position including all materials, lbours and t & p etc. for proper completion of the work. tank should be isi marked, sintex or equivalent and i / c all taxes.500litrescapacity 89 providing and fixing square mouths. w. gully trapgrade `a complete with c.i. gratingbrickmasonry chamber with f.p.s bricks and water tight ci cover with frame of 300 x 300 mm size ( inside ) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design. 150 x 110 mm. size p type 90 providing & fixing 450 mm long c. p. brass towel railcomplete with c.p. brass bracketsfixedtowoodencleats with c.p. brass screw. 91 providing & fixing isi marked ( is : 778 ) brass gatevalve ( class 1, pn 1 mpa ) with wheel of approvedquality ( screwed end ) . 15 mm nominal bore 92 same as in above item but for 20 mm nominal bore 93 providing & fixing of medium class pvc spout up to 300 mm. length including cutting and making good the walls and floors etc. as required. 50 mm dia 94 providing and fixing of chlorinated polyvinyle chloride ( cpvc ) pipes, having thermal stability for hot and cold water supply, including all cpvc plain and brass threaded fittings. this includes jointing of pipes and fittings with one step cpvc solvent cement, trenching , reifilling and testing of joints complete as per engineer in charge. external work.40mm dia nominal bore 95 same as in above item but for 50mm dia nominal bore 96 providing & fixing gun metal gate valve with c.i. wheel of approvedquality ( screwed end ) .50 mm nominal bore 97 construction of sewer connecting chamber having internal size 60 x 60 x 60 cm constructed in class 150 brick work in 1:6 cement and coarse sand mortar, 10 cm thick pcc 1:4:8 in base and internal side plasterred with 1:3 cement and coarse sand mortar including a floating coat of neat cement and 2.5 cm thick pcc 1:2:4 flooring of chamber and 5 cm thick top cover in rcc 1:1.5:3 including reinforcement steel ( analysis rate ) 98 internal electrificationwiring point for light with 1 sq. mm fr pvc insulated multistrand single core copper conductor cable in heavy guage pvc conduit pipe partly concealed in the wall and partly laid in slab with 1.5 sq. mm fr pvc insulated multistrand copper conductor cable as earth wire drawn inside of pipe, piano type switch and ceiling rose / angle / batten holder on 3 mm thick phenolic paminated backalite sheet etc. switches shall be fixed on suitable size ms box shunked in wall with 3 mm thick phenolic paminated backalite sheet and brass screws and washers complete in all respect as directed by engineering in charges including matching colour wash. 99 same as above item but for fan and fresh air fan. 100 same as above itembutfor 5ampplug point with piano type switch & socket etc. 101 same as above item but for call bellwith piano type switch or socket etc. 102 supply and fixing of power plug with 15a / 240v flush type switch and 5 pin 15a / 250 v flush type universal socket in suitable ms box of 175 mm x 100 mm x 50 mm size with henolic laminated bakelite sheet cover 3 mm thick fixed with brass machine screw and cup washer. 103 suppply and wiring of submain 2 number 2.5 sqmm fr pvc insulated 1100 v grade multisterilizationanded single core copper conductor cable in heavy duty 20 mm dia pvc conduit partly concealed in wall and partly laid in slab along with one number 1.50 sqmm fr pvc insulated multisterilization and copper conductor cable as earth contunity wire etc. complete in all respects. 104 suppply and wiring of submain 2 number 4 sqmm fr pvc insulated 1100 v grade multisterilizationanded single core copper conductor cable in heavy duty 20 mm dia pvc conduit partly concealed in wall and partly laid in slab along with one number 2.50 sqmm fr pvc insulated multisterilization and copper conductor cable as earth contunity wire etc. complete in all respects. 105 suppply and wiring of submain 2 number 6 sqmm fr pvc insulated 1100 v grade multisterilizationanded single core copper conductor cable in heavy duty 20 mm dia pvc conduit partly concealed in wall and partly laid in slab along with one number 4 sqmm fr pvc insulated multisterilization and copper conductor cable as earth contunity wire etc. complete in all respects. 106 suppply and wiring of submain with 4 number 10 sqmm fr pvc insulated 1100 v grade multisterilizationanded single core copper conductor cable in heavy duty 32 mm dia pvc conduit partly concealed in wall and partly laid in slab along with two number 6 sqmm fr pvc insulated multisterilization and copper conductor cable as earth contunity wire etc. complete in all respects. 107 s / f of surface / flush mountingspn distribution board without mcbcompletein all respects as directed at site.4 ways 108 s&f and making connection of 25a 2 pole 30ma elcb / rccb of din rail mounting complete in all respect as per direction and satisfaction to the engineer in charge. 109 s&f and making connection of 63a 2 pole 30ma elcb / rccb of din rail mounting complete in all respect as per direction and satisfaction to the engineer in charge. 110 supply, installation, testing and commissioningof main distributionboard suitable for required size incomer and single / three phase outgoing mcbs, ip 42 protection, double metal door, factory fabricated, wall mounting type in surface / recess, powder coated, 415 v / 250 amp copper bus bar, earth and neutral bar, removable gland plates, cable glands including connection with outgoing feeders completeinall respect. 111 s / f of surface / flush mountingspn distribution board without mcbcompletein all respects as directed at site. 12 ways 112 supply & fixingof 6 / 10 / 16 / 20 / 25 / 32 amp. sp mcb ( 10 ka ) 113 s / f of consumer unit flush / wall mounting type controlled by incoming 32 amp / 240 v spn switch fuse with outgoing circuits of 4 way 16 amp 240 v rewireable type distribution fuse boardcompletewith complete in all respects. ( cat. b ) 114 supply&burryingof 600mm x 600mm x 6.0mm g.i. plate, vertically for earthing with its top at least 3 m below ground level complete 20mm dia. g.i.pipe and funnelforwatering and one earthing lead ofno. 8swgg.i. wirein 15 mm dia. gi pipe uptoswitch board ( from apron to switch boardthecost of gi pipe & gi wire willbeextra ) 300mm square c.i. box with hinged cover, masonary housing alternate layer of charcoal / coke and salt atleast 150mm thick alround etc. as per the direction of engineer in charge complete in all respect . 115 supplying & laying of one number 8 to6 swg g. i. wirein 15 mm. dia. g. i.pipefor earthing, laidin groundor inwall duly concealedincludingthecostofcement, sand, labour, t&pandothermaterial required for proper completion ofthework as directed at site. 116 s / f of single light wall bracket on matching m.d.f.e.g. board base etc. completeinall respects. category a. 117 supply and fixing of recess / surface / pendent mounting round 10 to 15 watt led down lighter having powder coated die cast aluminium housing with heat sink, diffuser / reflector and driver set complete in all respect cat aaa 118 supply and fixing of led tube light with batten suitable for up to 1 x 22 watt led tube light complete including tube etc on surface complete in all respect.cat aaa 119 supply and fixing of electronic fan regulator 120 280 v isi marked on the existing switch board including making connection, required material, labour t&p etc. for proper completion of work to the satisfaction on engineer in charge of work. 120 s / f of hexagonal fan box with hexagonal side of approx. 80 mm.in lengthfabricatedfrom 16 swg m.s. sheet incorporating with10 mm. dia. m.s. round bar duly bent for supporting fan hanger duly painted with redoxideand screwingarrangementwithwiringconduit laid in the r.c.c.roofbeforeconcreting along with supply of all materials, labour, t&p etc. for proper completion of work. 121 s / f of doorchimeonpolishedm.d.f.e.g. board includingmakingconnectionsetc. complete in all respects. 122 supply of ceilling fans with fan motor of a.c. permanent insulation, capacitor rating conforming bee 5 starr rating and is:374 / 79 and also comply with is: 1709 / 1984 with latest amendment. the rated voltage 220 / 240 volts, 50hz, 1 ph ac the fan assemble should consits of down rod blades, shackle canopies etc. and with double ball bearing system. ( i ) bee 5 star rated 1200 mm sweep 123 supply of ac230 / 250 volts, 50 hz exhaust fansincluding providingnuts, bolts, mounting frame and other accessories etc. complete. ( make : bajaj / usha / newtek / havells ) 300 mm sweep...

Uttar Pradesh Jal Nigam - Uttar Pradesh

32922512 supply of materials for various modification and renovation works under “sugamya bharat abhiyan” at board of revenue, lucknow board of revenue ( remaining items ) board of revenue ( remaining items ) , dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead for thickness of tiles 10 mm to 25 mm , 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 ( 1 cement: 4 coarse sand ) , dismantling doors and windows, chowkhats with holdfast and including stacking of materials as directed by engineer in charge with in adistance of 60 metre. , dismantling doors and windows leaves and including stacking of dismantled materials as directed by engineer in charge with in adistance of 60 metre. , repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.metersand under, including cutting the patch in proper shape, raking out joints andpreparing and plastering the surface of the walls complete, including disposalof rubbish to the dumping ground, all complete as per direction of engineerin charge. ground floor , 6 mm cement plaster 1:3 ( 1 cement : 3 fine sand ) finished with a floating coat ofneat cement and thick coat of lime wash on top of walls when dry for bearingof r.c.c. slabs and beams ground floor . , making grooves 10 to 12 mm wide x 8mm deep in of the wails or in ceiling vertically or horizontallyas required , providing and laying ceramic glazed floor tiles of size 300x300 mm ( thicknessto be specified by the manufacturer ) of 1st quality conforming to is : 15622 ofapproved make in colours such as white, ivory, grey, fume red brown, laid on20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with greycement slurry @ 3.3 kg / sqm including pointing the joints with white cementand matching pigment etc., complete. , providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineerin charge, in skirting, risers of steps and dados, over 12 mm thick bed of cementmortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matchingshade complete. , cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stoneaggregate ) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate. , providing and fixing isi marked flush door shutters conforming to is : 2202 ( parti ) non decorative type, core of block board construction with frame of 1st classhard wood and well matched commercial 3 ply veneering with vertical grains orcross bands and face veneers on both faces of shutters: 35 mm thick including isi marked stainless steel butt hinges with necessary screws , providing and fixing m.s. rivets of sizes in position. , providing and fixing of hold fast for chaukhats of door sin addition, windows. , providing of door / windows grill , z section steel windows ( open able ) , angle iron door chaukhats 40x40x5 , fixing of door, window / ventilator chaukhats in position , one priming coat & one coat oil distemper on new work including supply of all materials, labour and t& p etc. required for proper completion of the work.as in item no.649 above but for every coat after the first coat ground floor , finishing walls with premium acrylic smooth exterior paint with siliconeadditives of required shade: new work ( two or more coats applied @ 1.43 ltr / 10 sqm over and includingpriming coat of exterior primer applied @ 2.20 kg / 10 sqm ) ground floor , one priming coat & one coat oil distemper on new work including supply of all materials, labour and t& p etc. required for proper completion of the work.as in item no.649 above but for every coat after the first coat ground floor , providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface toprepare the surface even and smooth complete.ground floor , painting or vanishing on iron works in small areas or new wood work with one coat of ready mixed priming paint & one coat of approved superior quality ready mixed paint of clear synthetic varnish including supply of all materials, labour and t & p etc. required for proper completion of work. paint to be used should confirm to the i.s.i. no. 103 1950.same as in item 641 above but for every coat after 1st coat. details of cost for 650 sft. area , wood surface. , providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes , ramp with slope 1:12 & width of 1.8 m & plinth height of 300 mm from ground level with steel handrails & chequred tiles. , supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. , providing and laying in position cement concrete of specified grade excludingthe cost of centering and shuttering all work up to plinth level : 1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) : 8 graded stone aggregate 40 mmnominal size ) , centering and shuttering including strutting, propping etc. and removal of formfor foundations, footings, bases of columns, etc. for mass concrete , providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all workup to plinth level : 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) : 3 graded stone aggregate 20 mmnominal size ) , brick work with common burnt clay f.p.s. ( non modular ) bricks of classdesignation 7.5 in foundation and plinth in: cement mortar 1:6 ( 1 cement : 6 coarse sand ) b / w in foundation , brick work with common burnt clay f.p.s. ( non modular ) bricks of classdesignation 7.5 in superstructure above plinth level up to floor v level in all shapesand sizes in : cement mortar 1:4 ( 1 cement : 4 coarse sand ) b / w up to plinth lvl. , steel reinforcement for r.c.c. work including straightening, cutting, bending, placingin position and binding all complete upto plinth level. thermo mechanically treated bars of grade fe 500d or more. , cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stoneaggregate ) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. , chequered precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cementslurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 10 mm thick bed of cement mortar 1:4 ( 1 cement: 4 coarse sand ) . ordinary cement without any pigment , providing and laying tactile tile ( for vision impaired persons as per standards ) of size 300x300x9.8mm having water absorption less than 0.5% and conforming to is: 15622, of approved make in all colors and shades in outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of engineer in charge. , providing and fixing stainless steel ( grade 304 ) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, i / c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer in charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. ) . , pathway marking , parking , internal electrical ( toilet ) , internal sanitary ( toilet ) , drinking water ( civil work ) , w / s for drinking water , cost of stainless steel handrail in stairs , cost of stainless steel handrail in corridors , cost of fire extinguisher , corridor marking , cost of reflector and anti skid nosing on staircase , cost of signage and general boards , supply, installation, testing & commissioning of lift ( 13 persons, 884 kg., 2 stops, 2 openings, car size 2000mm wide x 2400mm deep, ) as per specification attached etc. of orient, thyssenkrupp, johnson, otis, concourse or equivalent. , supply and fixing of structuralsteel frame ( such as tees, angles, channels etc ) & outer glazing with acp ( acp covering ) , each additional floor , providing and fixing of water cooler , providing of reception counter , supply and providing of wheel chair for disabled person at each floor , side table 1500*750*750mm with 3 drawer , reception chairs , bench ( stainless steel ) for blind , mess table for disabled , evacuation chairs to be available in every floor...

Uttar Pradesh Jal Nigam - Uttar Pradesh

32628364 addition work in special stadium at dr. shakuntala mishra national rehabilitation university mohan road lucknow addition work in special stadium at dr. shakuntala mishra national rehabilitation university mohan road lucknow , epabx system i.s.d.n , p.r.i, ip gatway system with facility to connect, 08 digital extns, 03p&t line & 16 analog extns with ip gatway expandable up to 96 extns, make: nec , operator console w/o. make: nec , digital phone 12 key . make: nec/ beetel / panasonic , analog phone.make: beetel / panasonic , telephone cable pvc 10pair make: delton/ finolex/ rr , telephone cable pvc 2 pair 0.5 mm make: delton/ finolex/ rr , idf with kron 30 pair , mdf with kron 30 pair , kron box10 pair , pvc casing/pipe . isi mark , equipment 9u rack (800x600)make top rack / comrack , 1 kva online ups make numeric / apc / microtek , supply, installation, testing & commissioning of a complete range of ceiling loudspeakers suitable for both speech and music reproduction in departmental stores, schools, sports halls, hotels, restaurants, public address applications and for any other general features: power handling capacity 6 watts, excellent frequency response, high sound pressure level, wide opening angle, in built 100v line matching transformer, contemporary aesthetic grill design, compact size, optimised for music & speech applications, ideal for mounting on false ceilings. item weight 1.03 kg, package dimensions 23.6 x 21.6 x 8.4 cm, speaker connectivity wired. make bosch / jbl / beeta3 , supply, installation, testing & commissioning of premium sound wall mount loudspeakers are intended for clear reproduction of speech, foreground and background music to be used in general indoor and outdoor applications. he premium sound cabinet loudspeaker is a 30 watt in a dark colour. the loudspeakers have selectable 8 ohm, 70 v and 100 v inputs. high fidelity music and speech reproduction , compact yet robust abs enclosure. make bosch / jbl / beeta3 , supply, installation, testing & commissioning of 250 watt amplifire rugged & reliable professional stereo power amplifier. input: balanced xlr & 1/4” jack. eq processing, low cut, subwoofer selection options on rear panel. stereo, bridge & parallel mode selection switch. protection: temperature ,dc short circuit. led indicators on front panel for power, signal, clip, bass boost & protect. mains voltage operation 220v ac 240v ac as well as low voltage operation (150v ac). output: speakon & binding post connectors. 19” rack mountable. make studiomaster / crown /jbl , supply, installation, testing & commissioning of 120 watt amplifire 180a, 280a and 1160a, ideal for commercial and industrial use, balanced phoenix type line inputs; touch proofed screw terminal speaker outputs, advanced protection system includes output current limiting, dc protection, circuit breaker/fuse, and thermal protection.make studiomaster / crown / jbl , supply, installation, testing & commissioning of two transducers two way full range,high spl and sensitivity speaker, one 15” big power low frequency transducer, one compression driver with 1.75” titanium diaphragm, driven by one amplifier with the possibility to drive a second 8 ohm monitor, (55° 100°) x 50° width direction to get more widely enlarged capability, system built in crossover two way full range speaker, cabinet plywood covering black toast painting, drivers quantity 15 x 1 (bass) 1 x ø44mm driver, frequency response ( 3db) 50hz 18khz, frequency response ( 10db) 45hz 20khz, sensitivity (db/1m/1w) 95db, impedance 8o, recommendatory power (rms/w) 250w, max sound level (db/1m) 120db,tweeter dispersion (hxv) (55° 100°) x 50°,harmonic distortion = 1%, connectors 2xnl4, 1+/1 ,dimensions (wxdxh) 430mm x 429mm x 621mm, packing dimensions (wxdxh) 712mm x 517mm x 541mm, net weight (kg/pcs) 18 kg, gross weight (kg/pcs) 20 kg. make bosch/ jbl / beta3 , supply, installation, testing & commissioning of 16 channel mixer air series mixers are the answer for budget conscious users who refuse to sacrifice sound quality and reliability. 16 mic / line, 3 band eq per channel. 1 aux send. pfl (cue) switch with individual channel control, l/r pan pot and clip led per channel. stereo rca cd input with control. delay efx on board & fx send per channel. 8 segments l/r led meter for master level. headphone output with level control. balanced xlr & ¼” jack master output. make studiomaster / sound craft /bosch , supply, installation, testing & commissioning of the driverack® pa2 provides all the processing you need between your mixer and amplifiers to optimize and protect your loudspeakers. with the latest advancements in dbx’s proprietary autoeq™ and afs™ algorithms, a new input delay module for delaying the foh system to the backline, ethernet control via an android®, ios®, mac®, or windows® device, and updated wizards, the driverack pa2 continues the driverack legacy of great sounding, powerful, and affordable loudspeaker management processors, for a whole new generation. make dbx / peavey , supply, installation, testing & commissioning of high quality uhf band frequency duel wireless microphone system,distance up to 100 feet(between receiver and microphone), ndividual channel output with level control & mix output. display on transmitter & receiver for frequency indication, two microphones can be used at the same time. make studiomaster / jbl /bosch , supply, installation, testing & commissioning of lapel mic variable frequency : 2 x 100 ( 100 per channel ).ultra high frequency wireless microphone system. plug & play. crystal clear sound. perfect choice for karaoke party, dj, wedding host, church, business meetings, public speaking, classroom activities, outdoor or onstage performances. make shure / maxcart , supply, installation, testing & commissioning of wired mic cardioid pickup pattern ensure excellent on axis pickup, designed for higher gain & less feedback, natural & fuller tone, suspended cartridge shock mount system minimizes handling noise, ideal microphone for vocals, choirs, instruments, speech programs & various pa applications, make studiomaster / jbl /bosch , supply, installation, testing & commissioning of microphone stand 1/2 size has been specifically designed & made high premium, the lightweight mini tripod design collapses into a compact shape and can be easily slipped, adjustment from the tripod, easily be adjusted to desired angle. make customise , supply, installation, testing & commissioning of microphone stand full size has been specifically designed & made high premium, the lightweight mini tripod design collapses into a compact shape and can be easily slipped, adjustment from the tripod, easily be adjusted to desired angle. make customise , supply, installation, testing & commissioning of podium providing & fixing of the wooden podium for speech approx size 52x30x21 made out of 19mm thick ply and 25mm wooden board(isi mark) fixing to the 4mm thick ply/sun mica on the wooden board on top complete as required (customised made) model no. make: customised. , supply, installation, testing & commissioning of podium mic cardioid pickup pattern ensure excellent on axis pickup, designed for higher gain & less feedback, natural & fuller tone, suspended cartridge shock mount system minimizes handling noise, ideal microphone for vocals, choirs, instruments, speech programs & various pa applications, make studiomaster / jbl /bosch , supply, installation, testing & commissioning of audio recorder four microphone inputs with 64db of smooth gain and phantom power, select four track recording mode of dual recording a distortion proof safety track, clear audio quality and a/d converters capture every whisper and shout of a performance, records up to 96jz/24 bit wav or bwav audio to sd card media, low cut filter and limiter to avoid noisy, distorted recordings. make tascam / zoom , supply, installation, testing & commissioning of dvd player hdmi one cable connection 1080p upscale, record to usb and usb content playback multi disc and format playback, phototv hd ; power requirements 110 240v, 50 / 60hz and power consumption (standby) less than 0.5 w, fast and slow playback with sound ; speaker surround sound channel configuration is 5.1, media type dvd video/cd/video cd/svcd, cd r/rw, mp3 (cd r/rw) (usb), jpeg (cd r/rw), kodak, (usb), aac (cd r/rw) (usb), wma (cd r/rw) (usb), lpcm (cd r/rw) (usb), mpeg 1 (cd r/rw) (usb), dvd/cd text. make sony / panasonic / ibell , sitc of24u floor mount rack 800 mm(w)/1000 mm(d) with front glass door and rear steel door, castor wheel with front brake (set of 4 nos). (make comrack / star) , sitc ofi7 pc with touch screen moniter, keyboard & mouse. make dell / hp / acer , sitc of smart ups 1kva 230v,30 minutes backup with batteryfor harsh envirotnment (make numeric/ resq / microtek , sitc ofspeaker cable make : crystal , sitc ofmicro phone cable , make : crystal , sitc oflxr connector male/female make : crystal , sitc ofrca socket , make : crystal , sitc ofelectric cable 3 core , sitc ofphono connector make : crystal , accessories for installation sound system , table (i shape) admire 5(w 1200 x d 600 x h 450) geeken. , executive chair gm 214 {high back chair, pu adjustable arm, gaslift, nylon base, fabric tapestry synchro knee tilt} geeken. , visitor chair gm 216 {visitor chair, wooden arm, chrome plated pipe frame, fabric tapestry powder coated} geeken. , steel almirah gms 37 steel almirah, 2 doors, 1 adjustable shelf, 1 locker, 1 hanging rod, thickness 0.8mm 915 x 530 x 2000 geeken. , 3 seater sofa (lider 3) geeken. , corner table(admire) geeken. , executive table (stelo 2) l1800xb1800xh750 geeken. , bed(hostel 1) geeken. , mattress , chair 3 seater geeken. , spectra – 3 , 3 seater sofa, chrome plated metal arm & legs, black powder coated rectangular tube cross beam, powder coated perforated shell, seat & back fabric tapestry. size:1820(l) 690(d) 790(h) geeken. , table alice centre table, ss pipe frame chrome finish, toughened glass top 12mm thick, lower glass 6mm thick, centre table, ss pipe frame chrome finish, toughened glass top 12mm thick, lower glass 6mm thick, 1200 x 600 geeken. , 3 seater sofa vegas 3 sofa with wooden frame, ss pipe legs, seat back leatherite tapestry size in mm 1800(l) 720(d) 790(h) geeken. , 2 seater sofa vegas 2 sofa with wooden frame, ss pipe legs, seat back leatherite tapestry size in mm 1300(l) 720(d) 790(h) geeken. , executive table (numero 9) geeken. , storage almirah (storage 10) geeken. , executive table (stelo 1) geeken. , stretcher deluxe gk 8004(size 2050x560) geeken. , wheel chair rigidgk 8006 geeken. , examination table gk 7007 geeken. , revolving stoolgk 4000 geeken. , cost of dinning table 4 capacity (geeken) gc 9008 (cafe table, s.s. 202 grade pipe frame, corian top size 1200 x 750, without top (only frame) geeken. , chairs (geeken) gc 919 {café chair, pipe frame,wooden seat chrome plated} geeken. , locker gms – 27 steel personal locker ( 16 locker ) geeken. , spectra 2 geeken. , table tennis table(made with 25 mm thick laminated board with 4 wheel, with heavy iron frame stucture) metco/kataki , badminton pole( movable posts for badminton: net wire tightening mechanism system very easy to operate as per new international standard base plate channel sheet ms round pole length: 1.55 mtr base wait ci casting one side wait 100kg pprox.w.t.3mm and other accessories like: bolt etc ss) , volley ball pole top quality (volleyball posts (heavy duty steel pipe power volleyball posts heavy duty steel pipe epoxy paint finish, wheels attached for easy movement) metco/kataki , volleyball poles sleeve’s cover made of stainless steel with sleeves cap metco/kataki , volleyball poles padding. , volleyball net plastic coated steel ware net (brand: garware). metco/kataki , volleyball net wire steel p.v.c. coated metco/kataki , foot ball goal post(football goal post (moveable) made of 4“ & 2” diameter pipe outer size: 20’x 7’ moveable with wheels.) metco/kataki , football net metco/kataki , basket ball pole(moveable basketball posts 25mm(foldable & roll able) transparent acrylic ckboards with international standard double die made frame with built in brackets for mounting dunking rim with three spring mechanism 3.2mtrs projection from the base pole with polyurethane wheels height adjustable with state of the art spring/ hydraulic operation technology. all system based on european pattern indigenously made with the help of best material. total weight 750 kg per pcs (1500 kg per pair)30mm basket ball board a grade malaysian board with angle frame 100% virgin monomer dunking ring with net) metco/kataki , cost of weight lifting platforms , trademill with screen metco/kataki , wheelchair treadmill metco/kataki , stair machine metco/kataki , cycles (spin bike with back support) metco/kataki , cycles (spin bike) metco/kataki , elliptical metco/kataki , rowing machne metco/kataki , chest press metco/kataki , shoulder press metco/kataki , lat pull down metco/kataki , pec dec fly metco/kataki , abdominal machine metco/kataki , leg curl and extension metco/kataki , leg press metco/kataki , leg press seated metco/kataki , bicep/triceps metco/kataki , cable crossover metco/kataki , adjustable abs bench metco/kataki , smith machine metco/kataki , rubber coated fixed barbells with straight and curl handle bar metco/kataki , viva fitness tpr solid dumbbells metco/kataki , rubber coated hexagon dumbbell metco/kataki , competition kettle bell metco/kataki , neoprene kettle bell dumbbell metco/kataki , viva fitness bumper plated metco/kataki , viva fitness tpr solid olympic plates metco/kataki , viva force olympic hole plates metco/kataki , coloured rubber coated olympic plates metco/kataki , 60 olympic bar ir 94051 metco/kataki , 47 ez curl bar ir 94047 metco/kataki , 20 olympic bar ir 94045 metco/kataki , chain link fencing to barricate the buildings , construction ofc.c. road , supply & fixing of 30m high mast with 12 nos.of led flood light 200w...

Ground Water Department - Uttar Pradesh

32611082 bids are invited for 1 boq item 1 two seater sofa, wooden frame, ss pipe leg, size in mm 1300 ( l ) x 780 ( d ) x 755 ( h ) supplying and placing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa shall have spring attached and also be padded separately. the frame shall be padded with high resilience polyurethane foam in seat and in back. there shall be cushion arm provided padded with high resilience polyurethane foam. the structure shall be upholstered with leatherite tapestry 1±0.2 mm thick ( minimum ) . the understructure shall consist of pipe frame leg of ss having cross section area 30mm x 30mm. there shall be shoe provided at the bottom to avoid scratches on the floor. the seat size shall be 510±10 mm ( d ) x 1040±10 mm ( w ) , seat height = 420±10 mm, overall width = 1300±10 mm, overall minimum depth = 780±10 mm & overall height = 755±10 mm. 4 2 boq item 2 centre table, ss pipe frame chrome finish, plpb edge banded top, 18mm thick, marino 10858 colour ( 1200 x 600 ) supplying & placing center table with an overall size minimum 1200mm x 600mm x 450mm. the top shall be made up of 18mm thick pre laminated particle board of grade ii of is 12823. the profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine. the side clad of the table shall be 18mm thick particle board. the under structure shall consist of ss 202 grade pipe frame cross section area 50mm x 10mm. there shall be ppcp shoe provided at the base to avoid scratches on the floor. 2 3 boq item 3 medium back chair, pp arm, gas lift, chrome base, leatherite tapestry, swivel tilt supplying and placing ergonomically designed, comfortable & aesthetically appealing medium back chair. the seat shall be made of 18mm thick hot pressed plywood with hr polyurethane foam 40mm thick having density minimum 40kg / m³ upholstered with leatherite tapestry with 0.8mm thick and the back shall be made of hot pressed plywood 15mm thick with hr polyurethane foam 12mm thick having density minimum23kg / m³ upholstered with leatherite tapestry in tan colour with minimum 0.8mm thick . the armrest shall be used pp arm completely joint with seat and back. the chair shall have swivel tilt revolving mechanism with single position locking and tilt tension adjustment. the pneumatic seat height adjustable 80mm with bifma standard class 3 gaslift. the pedestal shall be made up of ms crca chrome plated having pitch circle dia 650 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with bifma standards. the seat size shall be 500±10 mm ( w ) x510±10 mm ( d ) and back size shall be 550±10 mm ( h ) from seat & overall height = 965±10 mm. 36 4 boq item 4 executive table, particle board top w1650 x d1900 x h750 supplying & placing executive table with credenza unit and pedestal unit in completely knock down conditions with an overall size minimum 1650mm x 1900mm x 750mm that is to be assembled at site. the construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. the worktop shall have the size 1650mm x 800mm made up of 50mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be enclosed with wire manager cap for electric provision. a pullout keyboard trey shall be provided of 18mm thick pre laminated particle board having size 550mm x 300mm. the trey shall be operated on sliding channel. the table top shall be supported on particle board base gable end. the end wall of the table on the side shall be topped by gable end. it should be made up of 25mm thick pre laminated particle board and profile shall be in linear shape with appropriate pvc edge banding. the table shall be clad with 18mm thick modesty panel which provide structural support for the table. it should be 18mm thick pre laminated particle board in linear shape with appropriate pvc edge banding connected with both end. there shall be buffers provided at the base to avoid scratches on the floor. the table shall have credenza unit for storage purpose with an overall size 1200mm x 450mm x 650mm. it should be made up of pre laminated particle board of grade ii of is 12823 with base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. it shall have atleast 2 box drawer, 1 filing drawer and 1 shutter. it should be operated with the assistance of ss handle, concealed crank hinge and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. it shall be mounted on injection moulded nylon castor. a mobile pedestal shall be provided with an overall size 400mm x 450mm x 650mm. the pedestal shall be made up of pre laminated particle board of grade ii of is 12823. pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. the pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. the drawer shall be operated with ss handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be locked with one single key. the pedestal shall be mounted over injection moulded nylon castor. all the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. 5 boq item 5 wooden storage, particle board structure w 1500 x d 450 x h 750 supplying & placing storage unit with an overall size 1500mm x 450mm x 750mm. it storage should be made up of pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. all profile i.e. side, back, top, shutter, facia, shelf, skirting shall be 18mm thick and base 9mm thick. the top and side shall be full round post form at front and other edges shall be sealed with thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at minimum 200 degree celsius. the storage shall have minimum 8 nos. of drawer, 1 nos. of adjustable shelf and 2 nos. of shutter. the drawer shall be operated with roller channel to enable smooth operation and concealed crank hinge with ss handle. the drawer shall have central locking mechanism in which all the drawer shall be synchronized lock with one single key and shutter shall have mp lock. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. there shall be buffers provided at the bottom to avoid scratches on the floor. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the boards used should meet international standards of quality and safety, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of elasticity bending tested as per is 2380. 20 6 boq item 6 curvilinear workstation [ sharing ] partition : 60mm thick of height 1200mm work top : 25mm thick pre laminated particle board gable end : 25mm thick pre laminated particle board pedestal : 18mm thick pre laminated particle board, 02 drawers + 01 filing , kbt . cpu trolley. supplying & placing workstation table in completely knock down conditions with an overall size 1560mm x 1410mm x 1200mm that is to be assembled at site. the worktop shall have the size 1500mm / 600mm x 1350mm / 600mm made up of 25mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the top profile shall be in curvilinear shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc. the top shall be supported on particle board base gable end. the end wall of the top shall be topped by gable end. it should be made up of 25mm thick pre laminated particle board and the profile shall be in linear shape with appropriate pvc edge banding. a pullout keyboard trey shall be provided of 18mm thick pre laminated particle board having size 550mm x 280mm. the trey shall be operated on keyboard channel. the workstation shall have panel based partition of 60 mm thick with overall height 1200mm. the partition shall be linear in profile and provided in front side of user. the top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions ( pre treated ) and duly powder coated with 40 60μ thick. the trims shall have the size 60mm x 19mm with 1.5mm thick covered with die cast end caps on joints 2 ways, 3 ways & 4 ways . the aluminium raceway shall be situated below the worktop with an overall size 116mm ( h ) x 60mm ( d ) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. the exposed vertical and horizontal faces of the frames shall be snap fitted with trims. there shall be soft board ( with fabric ) provided at front of the user. laminated bottom tile shall be situated below the work top. the partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data ( lan ) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. slots / cut outs should be given on raceways to fix all electrical and data points. zinc coated small top support brackets shall be fixed on the partition for table top support. . adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. mobile pedestal shall be provided with an overall size 400mm x 450mm x 680mm. the pedestal shall be made up of pre laminated particle board of grade ii of is 12823. pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. the pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. the drawer shall be operated with ss handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the pedestal shall be mounted on injection moulded nylon castor. a nylon castor based cpu unit shall be provided with an overall size 470mm x 286mm with 18mm thick pre laminated particle board. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. 7 boq item 7 linear work station [ sharing ] partition : 60mm thick of height 1200mm work top : 25mm thick pre laminated particle board gable end : 25mm thick pre laminated particle board pedestal : 18mm thick pre laminated particle board, 02 drawers + 01 filing kbpt & cpu trolley providing and placing workstation table in completely knock down conditions with an overall size minimum 1320mm x 600mm x 1200mm that is to be assembled at site. the work top shall have the size 1200mm x 600mm made up of 25mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the profile of the top shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc . a pullout keyboard trey shall be provided of 18mm thick pre laminated particle board having size 525mm x 300mm. the trey shall be operated on keyboard channel. the workstation shall have panel based partition of 60 mm thick with overall height 1200mm. the partition shall be linear in profile and provided in the front side of user. the top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions ( pretreated ) and duly powder coated with 40μ 60μ thick. the trims shall have the size 60mm x 19mm with 1.5mm thick covered with die cast end caps on joints 2 ways, 3 ways & 4 ways . the aluminium raceway shall be situated below the worktop with an overall size 116mm ( h ) x 60mm ( d ) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. the exposed vertical and horizontal faces of the frames shall be snap fitted with trims. there shall be soft board ( with fabric ) and marker board provided at front of the user. laminated top tile and bottom tile shall be situated at both sides of the user and below the work top respectively. the partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data ( lan ) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. slots / cut outs should be given on raceways to fix all electrical and data points. zinc coated small top support brackets shall be fixed on the partition for table top support. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. fixed type pedestal shall be provided with an overall size 400mm x 450mm x 725mm. the pedestal shall be made up of pre laminated particle board of grade ii of is 12823. pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. the pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. the drawer shall be operated with ss handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized lock with one single key. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. 21 8 boq item 8 low back chair, pu arm, pu moulded seat & back, gas lift, nylon base, fabric tapestry. swivel tilt providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick in seat and 40mm thick in back. the same shall be upholstered with fabric tapestry 1mm thick and 300 gsm. the back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with back support. the seat and back shall be arrested together with 50 60μ thick powder coated hr steel spine and the armrest shall be made of black integral metal insert polyurethane arm completely joint with seat and back. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standard. the pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 650±15 mm and fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black minimum 30% glass filled nylon, confirming to ansi / bifma x5.1 2011 standard tested to perform 98, 000 cycles with 250lbs load. the seat size shall be 460±10 mm ( w ) x 450±10 mm ( d ) and back size shall be 460±10 mm ( w ) x 400±10 mm ( h ) from seat. seat height = 460±10 mm, overall height shall be = 810±10 mm. 63 9 boq item 9 conference table table top, gable end made of 25mm thick pre laminated particle board, modesty in 18mm thick pre laminated particle board, metal wire carrier width 5700 depth 5400 height 750 ( as per layout supplying & placing conference table in completely knock down conditions with an overall size minimum 5400mm x 5700mm x 750mm that is to be assembled at site. the construction of the main table shall be with minifix dowels, pins and ms brackets. the top shall be made up of back to back 25mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the top profile shall be in racetrack rectangular shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc . the table top shall be supported on particle board base gable end. the end wall of the table on the side shall be topped by gable end. it should be made up of 25mm thick pre laminated particle board and the profile shall be in linear shape with appropriate pvc edge banding. the table shall be clad with 18mm thick modesty panel which provide structural support for the table. the modesty panel shall be 18mm thick pre laminated particle board with appropriate pvc edge banding connected with both end. wire carrier shall be provided below the table top for power connection having size 60mm x 125mm made of 0.8mm thick high yield strength of crca sheet of grade d confirming to is:513 with duly powder coated. there shall be buffers provided at the base to avoid scratches on the floor. the table connections have to be made in such a way that no gap should be seen in between. the manufacturer shall have quality and safety assurance like i0so 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. 10 boq item 10 high back chair, pp arms, gas lift, chrome base, leatherite tapestry, swivel tilt supplying and placing ergonomically designed high back chair. the seat shall be made of 18mm thick hot pressed plywood with hr polyurethane foam 40mm thick upholstered with leatherite tapestry in black colour with 0.8mm thick and 535 gsm and the back shall be made of hot pressed plywood 15mm thick with hr polyurethane foam 12mm thick upholstered with leatherite tapestry in tan colour with 0.8mm thick and 535 gsm. headrest shall be provided for comfort of head with leatherite tapestry. the armrest shall be used pp arm completely joint with seat and back. the chair shall have swivel tilt revolving mechanism with single position locking and tilt tension adjustment. the pneumatic seat height adjustable 80mm with bifma standard class 3 gaslift. the pedestal shall be made up of ms crca chrome plated having pitch circle dia 650 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with bifma standards. the seat size shall be 500±10 mm ( w ) x500±10 mm ( d ) and back size shall be 720±10 mm ( h ) from seat & overall height = 1135±10 mm. 1 11 boq item 11 steel almirah, 2 doors, 4 adjustable shelf, thickness 0.8mm, 915 x 485 x 1980 providing, supplying and placing steel almirah in perfectly upright and straight position. the overall size of the almirah shall be minimum 915mm ( w ) x 485mm ( d ) x 1980mm ( h ) including legs. it should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. door shall be made of 1mm thick and all other components shall be made of 0.8mm thick high yield strength crca sheet of grade ‘d’ confirming to is: 513. stiffeners shall be provided in shelf & door. the steel hinged door shall be provided with locking mechanism which is assembled with bolt arrangement. the shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. uniformly distributed load capacity per each shelf shall be 40kg maximum. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to be thickness 50 60μ. 24 12 boq item 12 steel almirah, 2 glass doors, 4 adjustable shelf, thickness 0.8mm providing, supplying and placing steel almirah. the overall size of the almirah shall be minimum 915mm ( w ) x 485mm ( d ) x 1980mm ( h ) . the almirah shall be supplied with 2 nos. of glass doors with 4 nos. of adjustable shelves i.e. 5 loading compartments. the glass used shall be 4mm thick clear. the shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. uniformly distributed load capacity of each shelf shall be 40 kg maximum. each rack shall be provided with stiffener at bottom for strength. the entire body panel and shelf shall be made of high yield strength 0.8mm thick and door 1mm thick crca sheet of grade ‘d’ confirming to is: 513. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40 50μ thick. 27 13 boq item 13 steel library rack ( single face ) , thickness 0.8mm ( w925 x d300 x h1800 ) providing, supplying and placing an open display book racks. the overall size of the rack shall be minimum 925mm ( w ) x 300mm ( d ) x 1800mm ( h ) . the rack shall be supplied with 4 nos. of adjustable shelves i.e. 5 loading levels. rack, side panel, skirting shall be made of 0.8mm thick high yield strength crca sheet of grade ‘d’ confirming to is: 513. side and top shall be covered with 18mm thick pre laminated particle board of grade ii of is 12823. the edges of the board shall be sealed with 2mm thick pvc edge banding. the add on units can be stacked width wise to form a bank of racks having common panel. back panel up to the bottom of third rack shall have additional rigidity. the shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. uniformly distributed load capacity per each shelf shall be 80 kg maximum. each rack shall be provided with stiffener at bottom for strength. label holder & range indicators on each main unit for inserting labels. all steel components shall be epoxy polyester powder coated to the thickness of 40 60μ. adjustable leveler shall be provided with metal insert to resist scratches on the floor and also level & support structure. 9 14 boq item 14 conference table, particle board edge banded top, 25 mm thick, w1800 x d900 x h750 supplying & placing conference table in completely knock down conditions with an overall size minimum 1800mm x 900mm x 750mm that is to be assembled at site. the worktop shall be made up of 25mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the profile shall be in rectangle shape with round front and back and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine. the table shall be supported on ms powder coated pipe frame having cross section area 40mm x 20mm. the understructure shall consist of crca powder coated 2 nos. vertical round pipe with dia. 110mm. the four legs shall be made up of ms chrome plated round pipe of dia. 38mm. a crca chrome plated round pipe of dia. 38mm shall be placed between legs for structural support. there shall be ppcp shoe provided to avoid scratches on the floor. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. 2 15 boq item 15 executive table, mdf veneer pu structure, top 2200 x 1000 x 750 eru 2200 x 600 x 600 supplying & placing modular table in completely knock down conditions with an overall size minimum 2450mm x 2200mm x 750mm that is to be assembled at site. the worktop shall have the size 2200mm x 1000mm x 76mm thick made up of medium density fibre board with approved veneer laminate and pu polish accordingly. the table top profile shall be in rectangle shape with round corners and full round post forming edges. the table top shall be supported on mdf board based gable end. the end wall of the table on the side shall be topped by gable end. it should be made up of 76mm thick medium density fibreboard and profile shall be in moulded construction with full round post forming edges and duly deco painted. the table shall be clad with 18mm thick modesty panel which provide structural support for the table. it should be 18mm thick medium density fibre board in linear shape with appropriate pvc edge banding and veneer laminate. there shall be buffers provided at the base to avoid scratches on the floor. the table shall have side unit for storage purpose with an overall size 2200mm x 600mm x 600mm. it shall have 2 nos. of drawer, 1 nos. of filling space with door and 1 nos of open space . the drawer shall be operated with profile handle and easily close & open with the assistance of sliding channels to enable smooth operation and sliding rail track and concealed crank hinge. drawer facai, sides and all other shall be made in min 18mm thick and drawer base shall be 9mm thick. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. the complete structure shall be supplied with approved veneer laminate, pu polish and deco painted. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. 2 16 boq item 16 back unit 1800 [ w ] x400 [ d ] x200 0 [ h ] mm [ storage facia & top veneer rest all laminated ] wooden storage plpb side glass door, veneer finish. supplying & placing storage unit with an overall size minimum 1800mm x 400mm x 2000mm. it should be made up of pre laminated particle board of grade ii of is 12823 with approved veneer laminate and finish as per approved shade. the top of the storage shall have minimum 50mm thick cantor top with full round post form. all other profile i.e. side, back, shutter, shelf, skirting shall be 18mm thick and base 9mm thick. the edges shall be sealed with thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the storage shall be supplied with 12 nos. of shelf, 2 nos. of drawer and 6 nos. of door shutter. the glass shutter shall be used with 4mm thick clear glass insert within plpb profile. the shutter and drawer shall be operated with concealed crank hinge and roller channel as well as ss handle. to protect the wall from kicks, abrasion and serve as a decorative molding skirting shall be provided at bottom. there shall be buffers provided at the bottom to avoid scratches on the floor. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the boards used should meet international standards of quality and safety, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of elasticity bending tested as per is 2380. 2 17 boq item 17 high back chair, metal chrome with cushion arms, knee tilt, gas lift, chrome plated base, leatherite tapestry providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. the seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam ( 30+25 ) mm thick and the back shall be made of ( 15+6 ) mm thick double layered moulded plywood padded with high resilience polyurethane foam 30mm thick . the same shall be upholstered with leatherite tapestry 1mm thick . the backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support & full back support as well as head support. the chair shall be supplied with chrome plated arm with cushion having leatherite covering top. for seating durability the chair shall have knee tilt 360 degree revolving mechanism having four position locking and tilt tension adjustment with anti shock feature which provides back strength for the chair. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal should have five legged ms crca chrome plated having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. the castors of the chair shall be injection moulded in black 30% glass filled nylon, confirming to ansi / bifma x5.1 2011 standards tested to perform 98, 000 cycles with 250lbs load. the seat size shall be 515±10 mm ( d ) x 545±10 mm ( w ) and back size shall be 560±10 mm ( w ) x 700±10 mm ( h ) from seat. overall height shall be = 1155±10 mm, overall depth / width = 760±10 mm. 2 18 boq item 18 visitor chair, metal chrome with cushion arm, chrome plated pipe stand, leatherite tapestry providing and supplying visitor chair with ergonomic design for user comfort & aesthetically appealing. the seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam ( 30+25 ) mm thick and the back shall be made of ( 15+6 ) mm thick double layered moulded plywood padded with high resilience polyurethane foam 30mm thick . the same shall be upholstered with leatherite tapestry 1mm thick and minimum 571 gsm. the backrest shall be made by keeping the natural curvature of the spine for back support. the chair shall be supplied chrome plated fixed arm with cushion having leatherite covering top and seat and back shall be arrested together with powder coated hr steel spine. the frame structure shall be cantilever support type made of ms crca chrome plated capsule pipe of size 40mm x 20mm with 1.6mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 510±10 mm ( d ) x 545±10 mm ( w ) and back size shall be 560±10 mm ( w ) x 520±10 mm ( h ) from seat. overall height shall be = 990±10 mm, overall depth = 660±10 mm & overall width = 680±10 mm. 19 boq item 19 three seater sofa, wooden frame, powder coated pipeleg, seat back leatherite tapestry, size in mm 2020 ( l ) x 750 ( d ) x 665 ( h ) supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa shall have spring attached and also be padded separately. the frame shall be padded with high resilience polyurethane foam having density minimum 40kg / m³ in seat and minimum32kg / m³ in back. there shall be cushion arm provided padded with high resilience polyurethane foam having density minimum40kg / m³. the structure shall be upholstered with leatherite tapestry 1±0.2 mm thick and minimum 571 gsm. the sofa shall be supported on ms powder coated pipe frame having size 40mm x 20mm. the under structure shall consist of ms powder coated round leg with upper dia. 38mm and lower dia. 30mm. there shall be shoe provided at the bottom to avoid scratches on the floor. the seat size shall be 570±10 mm ( d ) x 1660±10 mm ( w ) , seat height = 425±10 mm, overall width = 2020±10 mm, overall depth = 750±10 mm & overall height = 680±10 mm. 2 20 boq item 20 single seater sofa, wooden frame, powder coated pipe leg, seat back leatherite tapestry, size in mm 960 ( l ) x 750 ( d ) x 665 ( h ) supplying and placing single seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa shall have spring attached and also be padded separately. the frame shall be padded with high resilience polyurethane foam having density minimum40kg / m³ in seat and minimum32kg / m³ in back. there shall be cushion arm provided padded with high resilience polyurethane foam having density minimum 40kg / m³. the structure shall be upholstered with leatherite tapestry 1±0.2 mm thick and 571 gsm. the sofa shall be supported on ms powder coated pipe frame having size 40mm x 20mm. the under structure shall consist of ms powder coated round leg with upper dia. 38mm and lower dia. 30mm. there shall be shoe provided at the bottom to avoid scratches on the floor. the seat size shall be 570±10 mm ( d ) x , seat height = 425±10 mm, overall width = 960±10 mm, overall depth = 750±10 mm & overall height = 680±10 mm. 4 21 boq item 21 centre table, ss pipe frame, chrome finish, toughned black glass, top 12mm thick, lower glass 8mm thick 1200 x 600 supplying & placing center table with an overall size minimum 1200mm x 600mm x 450mm. the top shall be made up of minimum 12mm thick toughened glass. the profile shall be in rectangle shape with bevelled edges. the bottom storage shelf shall be provided with an overall size 1155mm x 280mm made of 8mm thick toughened glass with bevelled edges. the glass shall be supported on vacuum caps situated over ss 202 grade pipe frame. the under structure shall have ss pipe frame having size 67mm x 13.5mm. there shall be ppcp shoe provided to avoid scratches on the floor. 2 22 boq item 22 visitor chair, pu arm, powder coated pipe stand, leatherite tapestry providing and supplying visitor chair with ergonomic design for user comfort. the seat and back shall be made of metal insert pipe frame padded with high resiliance polyurethane foam ( 30+19 ) mm thick having density minimum ( 60+40 ) kg / m³ in seat 19mm thick having density minimum23kg / m³ in back. the same shall be upholstered with leatherite tapestry 0.8mm thick and minimum 535 gsm. the backrest of the chair shall be made by keeping the natural curvature of the spine with lumbar support. the armrest shall be used polyurethane arm completely joint with seat and back. the frame structure shall be cantilever support type made up of ms / crca powder coated round pipe of dia. 25.4mm with 2mm thick. there shall be co polymer polypropylene shoe provided at the base to avoid scratches on the floor. the seat size shall be 480±10 mm ( w ) x 470±10 mm ( d ) and back size shall be 460±10 mm ( h ) from seat & overall height = 870±10 mm. 2 23 boq item 23 wooden bed, particle board structure, powder coated pipe frame, ppcp shoes 2060 ( l ) x 1131 ( b ) x 930 ( h ) with mattress supplying and placing single bed with an overall size minimum 2060mm ( l ) x 1131 ( b ) x 930mm ( h ) . head and tail panel shall be made of minimum18mm thick pre laminated particle board and baton shall be made of minimum 32mm thcik mdf board duly bull nose shape. sides baton shall be made of 32mm thick mdf board ( one side full round post forming ) and 18mm thick particle board with 2mm thick pvc edge banding . mattress panel shall be made of minimum 18 mm thick particle board. the understructure shall consist of ms channles in 1mmm thickness. horizontal and bottom plinth shall be made of 25mm thick pre laminated particle board. 2 24 boq item 24 bedside table plpb board 400 x 400 x 415 supplying and placing in position of bed side tableof approved make colour with superior design and as per approved drawing & design of engineer incharge. minimum overall size : depth 461.0 mm width 460.0 mm height 510.0 mm material : body panels of bed side table are made of minimum 18 mm thick prelaminated particle board .all the exposed edges are edge banded with 0.8 mm thick pvc edge banding. drawer front & door are made of 18 mm thick prelaminated particle board with imported h.d.f. foil wrapped decorative trim fixed on to it as per direction of engineer in charge. hardware : the high quality hardware used like roller slides, hinges , minifix, dowels is of make hettich . construction : knock down construction. finish :. minimum18 mm thick prelaminated particle board is in maple shade.the participating brand must have all the prevalent quality & safety related certifications like iso:9001, iso:50001, iso:14001, iso 45001:2018, bifma, & aiota. one or more product shall be certified from green guard ul of usa. the participating brand must have all the prevalent quality & safety related certifications like iso:9001, iso:50001, iso:14001, iso 45001:2018, bifma, aiota for one or more product, green guard certificate for any one product atlest issued by ul of usa. . 25 boq item 25 executive table, particle board top w2250 x d2100 x h750 supplying & placing modular table in completely knock down conditions with an overall size minimum 2250mm x 2100mm x 750mm that is to be assembled at site. the work top shall have the size 1900mm x 900mm made up of 50mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the top shall be 50mm thick on edges, after 100mm from edges it should be 25mm thick. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel .. the table top shall be supported on ms powder coated pipe frame having cross section area 50mm x 25mm with 1.6mm thick. the end wall of the table on the side shall be topped by gable end. the gable end shall be made up of 50mm thick pre laminated particle board and profile shall be in linear shape with appropriate pvc edge banding. the table shall be clad with 18mm thick modesty panel which provide structural support for the table. it should be 18mm thick pre laminated particle board in linear shape with appropriate pvc edge banding connected with both end. the table shall have side unit for storage purpose with an overall size 2100mm x 600mm x 641mm. the side unit shall be made up of pre laminated particle board of grade ii of is 12823 with drawer base 9mm thick & other parts 18mm thick like shutter, back, facia, top etc. it shall have minimum 3 drawer, 1 shutter and 2 sliding shutter. the drawer shall be operated with ss handle and easily close & open with the assistance of roller channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be locked with one single lock. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet , indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. 4 26 boq item 26 wooden storage, particle board structurew 1200 x d 400 x h 1850 supplying & placing storage unit with an minimum overall size minimum 1200mm x 400mm x 1850mm. it should be made up of pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. all profile i.e. side, back, shutter, shelf, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable pvc. the storage shall have minimum 6 nos. of fixed shelf and 6 nos. of door shutter for ease of opening. . there shall be buffers provided at the bottom to avoid scratches on the floor. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the boards used should meet , indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of elasticity bending tested as per is 2380. 5 27 boq item 27 high back chair, wooden cushion arm, torsion bar, gas lift, chrome base providing and supplying high back chair. the seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam ( 50+25 ) mm thick having density minimum ( 40, 32 ) kg / m³ and the back shall be made of double layered moulded plywood ( 12+6 ) mm thick padded with high resilience polyurethane foam ( 30+12 ) mm thick having density minimum ( 32, 23 ) kg / m³. the same shall be upholstered with leatherite tapestry 0.8mm thick and minimum 535 gsm. the backrest of the chair shall be made by keeping the natural curvature of the spine which helps to provide lumbar support as well as head support. the chair shall be supplied with cushion arm having leatherite covering top. for seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal should have five legged die cast aluminium having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. the castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ansi / bifma standards x5.1 2011 tested to perform 98, 000 cycles with 250lbs load. the seat size shall be 510±10 mm ( d ) x 500±10 mm ( w ) and back size shall be 515±10 mm ( w ) x 715±10 mm ( h ) from seat. overall height shall be = 1165±10 mm, base width / depth = 760±10 mm. 5 28 boq item 28 visitor chair, cushion arm, chrome plated pipe stand, leatheritte tapestry providing and supplying a visitor chair with ergonomic design for user comfort & shall have aesthetically appealing. the seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foamminimum ( 50+25 ) mm thick having densityminimum ( 40, 32 ) kg / m³ and the back shall be made of double layered moulded plywood minimum ( 12+6 ) mm thick padded with high resilience polyurethane foam minimum ( 32+12 ) mm thick having density minimum ( 32, 23 ) kg / m³. the same shall be upholstered with leatherite tapestry 0.8mm thick and 535 gsm. the backrest shall be made by keeping the natural curvature of the spine for back support. the chair shall be supplied with cushion arm having leatherite covering top. the frame structure shall be cantilever support type made up of ms crca chrome plated tubular pipe of size 40mm x 20mm with 1.6mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 500±10 mm ( d ) x 515±10 mm ( w ) and back size shall be 515±10 mm ( w ) x 540±10 mm ( h ) from seat. overall height shall be = 945±10 mm, overall depth = 690±10 mm & overall width = 580±10 mm. 29 boq item 29 three seater sofa, wooden frame, ss pipe leg frame, sear back leatherite tapestry, size in mm 1900 ( l ) x 770 ( d ) x 800 ( h ) supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa shall have spring attached and also be padded separately. the frame shall be padded with high resilience polyurethane foam having density minimum 40kg / m³ in seat and minimum 32kg / m³ in back. there shall be cushion arm provided padded with high resilience polyurethane foam having densityminimum 40kg / m³. the structure shall be upholstered with leatherite tapestry 1±0.2 mm thick and minimum 571 gsm. the understructure shall consist of pipe frame loop leg of ss shiny chrome finish having cross section area 40mm x 20mm. there shall be shoe provided at the bottom to avoid scratches on the floor. the seat size shall be 510±10 mm ( d ) x 1540±10 mm ( w ) , seat height = 435±10 mm, overall width = 1860±10 mm, overall depth = 770±10 mm & overall height = 780±10 mm. 1 30 boq item 30 ( as per layout room size : 16340x7870mm ) conf erence table table top, gable end made of 25mm thick pre laminated particle board, modesty in 18mm thick pre laminated particle board, metal wire carrier ( 13200 x4200x 750 ) mm supplying & placing conference table in completely knock down conditions with an overall size 13200mm x 4200mm x 750mm that is to be assembled at site. the construction of the main table shall be with minifix dowels, pins and ms brackets. the top shall be made up of back to back 25mm thick prelaminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the top profile shall be in racetrack rectangular shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel . the table top shall be supported on particle board base gable end. the end wall of the table on the side shall be topped by gable end. it should be made up of 25mm thick pre laminated particle board and the profile shall be in linear shape with appropriate pvc edge banding. the table shall be clad with 18mm thick modesty panel which provide structural support for the table. the modesty panel shall be 18mm thick pre laminated particle board with appropriate pvc edge banding connected with both end. wire carrier shall be provided below the table top for power connection having size 60mm x 125mm made of 0.8mm thick high yield strength of crca sheet of grade d confirming to is:513 with duly powder coated. there shall be buffers provided at the base to avoid scratches on the floor. the table connections have to be made in such a way that no gap should be seen in between. the manufacturer shall have quality and safety assurance like i0so 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. 1 31 boq item 31 high back chair, pipe frame, pu chrome arm, gas lift, chrome base, leatherite tapestry, swivel tilt supplying and placing ergonomically designed, comfortable & aesthetically appealing high back chair. the seat shall be made of 15mm thick hot pressed curved plywood upholstered with high resilience polyurethane foam 50mm thick having density minimum 40kg / m³ with khaki leatherite tapestry 0.8mm thick and 535 gsm and the back shall be supported by metal insert ms crca frame upholstered with high resilience polyurethane foam 12mm thick having density minimum 23kg / m³ with khaki leatherite tapestry 0.8mm thick and minimum 535 gsm with contoured lumbar support which helps to provide full back support and maintain the natural curvature of the spine. headrest shall be provided for comfort of head with leatherite tapestry. the armrest shall be used ms crca chrome plated with pu arm completely joint with seat and back. the chair shall have knee tilt 360 degree revolving mechanism with four position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height upto 100mm with bifma standard class 3 gaslift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal shall be made up of ms crca chrome plated having pitch circle dia 640 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with bifma standards. the seat size shall be 485±10 mm ( w ) x520±10 mm ( d ) and back size shall be 740±10 mm ( h ) from seat, overall height = 1150±10 mm and overall depth / width= 740±10mm. 4 32 boq item 32 medium back chair, pipe frame, pu chromearm, gas lift, chrome base, leatherite tapestry, swivel tilt providing and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. the seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be supplied with inserted pipe frame. the chair shall be padded with high resilience polyurethane foam 50mm thick having density 40kg / m³ in seat and 12mm thick having density 23kg / m³ in back. the same shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 gsm and breathable mesh tapestry behind the backrest. ms chrome plated pipe frame shall be provided on both side of seat and back with size 25mm x 10mm. the backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support. the armrest shall be used black integral polyurethane arm mounted on crca chrome plated pipe having size 40mm x 10mm completely joint with seat and back with the assistance of allen key screw. a chrome plated round bend pipe of dia. 9mm shall be provided behind the backrest of the chair and welded with main frame. for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal shall have five legged crca chrome plated having pitch circle dia. 650mm fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled, confirming to ansi / bifma standards x5.1 2011 tested to perform 98, 000 cycles with 250lbs load. the seat size shall be 490±10 mm ( w ) x 520±10 mm ( d ) and back size shall be 450±10 mm ( w ) x 535±10 mm ( h ) from seat & overall height = 980±10 mm, overall width = 560±10 mm & overall depth = 670±10 mm 33 boq item 33 visitor chair, pipe frame, pu chrome arm, chrome plated pipe stand, leatherite tapestry, chrome plated providing and supplying a visitor chair with ergonomic design for user comfort & shall have aesthetically appealing. the seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be supplied with metal pipe, inserted between backrest. the chair shall be padded with high resilience polyurethane foam 50mm thick having density 40kg / m³ in seat and 12mm thick having density 23kg / m³ in back. the seat and back shall be upholstered with leatherite tapestry 0.8±0.1mm thick, 535 gsm and breathable mesh tapestry behind the backrest. ms chrome plated pipe frame shall be provided on both side of seat and back with size 25mm x 10mm. the backrest shall be supplied by keeping the natural curvature of the spine which helps to provide back support. the armrest shall be used black integral polyurethane arm mounted on crca chrome plated pipe having size 40mm x 10mm completely joint with seat and back with the assistance of allen key screw. chrome plated round bend pipe of dia. 9mm shall be provided behind the backrest of the chair and welded with main frame. the frame structure shall be cantilever support type made of ms crca chrome plated round pipe of dia. 25.4mm with 2mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 500±10 mm ( w ) x 510±10 mm ( d ) and back size shall be 450±10 mm ( w ) x 540±10 mm ( h ) from seat & overall height = 980±10 mm, overall width = 560±10 mm. 20 34 boq item 34 three seater desk, plpb edge banded top, seat & back, powder coated pipe frame, top size 1500 x 400 x 18mm thick overall size 1500 x 980 x 750 providing and supplying desk cum bench ( three seater ) with an overall size 1560mm x 980mm x 750mm. the top of the desk shall be made up of 18mm thick pre laminated particle board of grade ii of is 12823 with approved laminate. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca rectangle pipe having cross section area 25mm x 25mm with 1.2mm thick. the shelf shall be made up of 18mm thick pre laminated particle board with 2mm thick pvc edge banding. it should be supported on crca rectangle pipe having cross section area 25mm x 25mm with 1.2mm thick. the side panel of the table shall be made of crca rectangle pipe having cross section area 40mm x 20mm with 1.2mm thick placed in vertical position at both side of the desk and bench. hooks should be provided on the vertical side frame on both side of the desk for hanging bags / bottles. the front of the desk shall be clad with modesty panel made up of 18mm thick pre laminated particle board hinged with front pipe frame. the seat and back shall be made up of 18mm thick pre laminated particle board and the edges shall be sealed with 2mm thick pvc edge banding. the seat and back shall be supported on crca square pipe having cross section area 25mm x 25mm with 1.2mm thick and 19mm x 19mm with 1.2mm thick respectively. 2 nos. footstep shall be provided for structural support of the desk having cross section area of the pipe 40mm x 20mm with 1.2mm thick. the complete steel structure shall be welded with base pipe having cross section area 40mm x 20mm with 1.2mm thick and also be epoxy polyester powder coated to the thickness 50 60μ thick. there shall be shoe provided at the base to avoid scratches as well as uneven surfacing. the size of the writing top shall be 1050mm ( w ) x 400mm ( d ) , seat size shall be 1050mm ( w ) x 300mm ( d ) , back size shall be 1050mm ( w ) x 200mm ( h ) . all the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification 14 35 boq item 35 high back chair, pu chrome arm, gas lift, chrome base, fabric tapestry, synchro tilt providing and supplying high back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of 15mm thick and ( 15+6 ) mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick having density minimum 40kg / m³ in seat and 25mm thick having densityminimum 32kg / m³ in back. the same shall be upholstered with fabric tapestry 0.6mm thick and minimum 235 gsm. the backrest of the chair shall be made by keeping the natural curvature of the spine with lumbar support as well as head support. the seat and back shall be arrested together with 40 60μ thick powder coated hr steel spine and the armrest shall be used polyurethane arm mounted on round pipe frame completely joint with seat. for seating durability the chair shall have synchro tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 80mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standard. the pedestal should have five legged ms / crca chrome plated having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. the castor of the chair should be injection moulded in black nylon 30% glass filled, confirming to ansi / bifma x5.1 2011 standard tested to perform 98, 000 cycles with 250lbs load. the seat size shall be 500±10 mm ( w ) x 485±10 mm ( d ) and back size shall be 710±10 mm ( h ) from seat & overall height = 1150±10 mm. 10 36 boq item 36 visitor chair, wooden arm, chrome plated pipe stand, fabric tapestry providing and supplying visitor chair with ergonomic design for user comfort. the seat and back shall be made of 15mm thick and ( 15+6 ) mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick in seat and 25mm thick having in back. the same shall be upholstered with fabric tapestry 0.6mm thick and 235 gsm. the backrest of the chair shall be made by keeping the natural curvature of the spine with lumbar support. the seat and back shall be arrested together with 50 60μ thick powder coated hr steel spine and the armrest shall be used wooden arm with melamine polish mounted on round pipe frame. the understructure shall consist of cantilever support frame made up of ms / crca round pipe having dia. 28.5mm with 2mm thick. the seat size shall be 480±10 mm ( w ) x 485±10 mm ( d ) and back size shall be 470±10 mm ( h ) from seat & overall height = 915±10 mm. 37 boq item 37 wooden storage, particle board structure w 900 x d 450 x h 750 supplying & placing storage unit with an overall size 900mm x 450mm x 750mm. the storage shall be made up of pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the top shall be 25mm thick and all other profile i.e. side, back, shutter, shelf, skirting shall be 18mm thick. the edges shall be sealed with thin strip of impermeable pvc. the storage shall have 1 nos. of adjustable shelf and 2 nos. of door shutters shall be provided for opening and closing the storage. . to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. there shall be buffers provided at the bottom to avoid scratches on the floor. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the boards used should meet international standards of quality and safety, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of elasticity bending tested as per is 2380. 2 38 boq item 38 partition : 60mm thick of height 1200mm work top : 25mm thick pre laminated particle board gable end : 25mm thick pre laminated particle board pedestal : 18mm thick pre laminated particle board providing and placing workstation table in completely knock down conditions with an overall size 1000mm x 600mm x 1200mm that is to be assembled at site. the work top shall have the size 880mm x 600mm made up of 25mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the profile of the top shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the workstation shall have panel based partition of 60 mm thick with overall height 1200mm. the partition shall be linear in profile and provided in the front side of user. the top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions ( pre treated ) and duly powder coated with 40μ 60μ thick. the trims shall have the size 60mm x 19mm with 1.5mm thick covered with die cast end caps on joints 2 ways, 3 ways & 4 ways ( l cover for corner, t cover for middle section wherever required ) . the aluminium raceway shall be situated below the worktop with an overall size 116mm ( h ) x 60mm ( d ) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. the exposed vertical and horizontal faces of the frames shall be snap fitted with trims. there shall be soft board ( with fabric ) and marker board provided at front of the user. laminated top tile and bottom tile shall be situated at both sides of the user and below the work top respectively. the partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data ( lan ) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. slots / cut outs should be given on raceways to fix all electrical and data points. zinc coated small top support brackets shall be fixed on the partition for table top support. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor.to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. 39 boq item 39 workstation table, panel based partition, w1320 x d660 x h1200 particle board edge banded top providing and placing workstation table in completely knock down conditions with an overall size 1320mm x 660mm x 1200mm that is to be assembled at site. the work top shall have the size 1200mm x 600mm made up of 25mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the profile of the top shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. a pullout keyboard trey shall be provided of 18mm thick pre laminated particle board having size 525mm x 350mm. the trey shall be operated on keyboard channel. the workstation shall have panel based partition of 60 mm thick with overall height 1200mm. the partition shall be linear in profile and provided in the front side of user as well as on the both sides of the user. the top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions ( pre treated ) and duly powder coated with 40μ 60μ thick. the trims shall have the size 60mm x 19mm with 1.5mm thick covered with die cast end caps on joints 2 ways, 3 ways & 4 ways ( l cover for corner, t cover for middle section wherever required ) . the aluminium raceway shall be situated below the worktop with an overall size 116mm ( h ) x 60mm ( d ) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. the exposed vertical and horizontal faces of the frames shall be snap fitted with trims. there shall be soft board ( with fabric ) and marker board provided at front of the user. laminated top tile and bottom tile shall be situated at both sides of the user and below the work top respectively. the partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data ( lan ) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. slots / cut outs should be given on raceways to fix all electrical and data points. zinc coated small top support brackets shall be fixed on the partition for table top support. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. fixed type pedestal shall be provided with an overall size 400mm x 450mm x 725mm. the pedestal shall be made up of pre laminated particle board of grade ii of is 12823. pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. the pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. the drawer shall be operated with ss handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized lock with one single key. to protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. a nylon castor based cpu unit shall be provided with an overall size 468mm x 284mm with 18mm thick pre laminated particle board. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. the board used should meet international standard of quality, indian standard is 12823 grade ii should meet long time load bending, screw withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per is 2380. 16 40 boq item 40 stool, without arm, chrome plated pipe frame with foot rest, nylon base, gas lift, seat & back leaherite tapestry supplying and placing bar stool. the seat shall be made of 15mm thick hot pressed commercial plywood upholstered with high resilience polyurethane foam 30mm thick and the back shall be made of metal insert pipe upholstered with high resiliance polyurethane foam 25mm thick leatherite tapestry 0.8mm thick and 535 gsm. the seat and back shall be fixed with metal pipe. the chair shall have 360 revolving mechanism. the pneumatic seat height adjustment for healthy seating, user can adjust seat height upto 240mm with bifma standard class 3 gaslift to suit them using the lever under the seat. footrest shall be provided of ms chrome plated round pipe of dia 16mm. the pedestal shall be made up of injection moulded black nylon having pitch circle dia 650 mm fitted with 5 nos. 50mm gliders which shall be made of injection moulded black nylon 30% glass filled. the seat shall be 440±10 mm ( d ) x 455±10 mm ( w ) and back size shall be 535±10 mm ( w ) x 260±10 mm ( ht ) from seat. overall height shall be = 875±10 mm. 16 41 boq item 41 steel almirah, 2 glass doors, 2 steel doors, adjustable shelf, thickness 0.8mm ( w900 x d450 x h1830 ) providing, supplying and placing steel almirah. the overall size of the almirah shall be 900mm ( w ) x 450mm ( d ) x 1830mm ( h ) . the almirah shall be supplied with 2 nos. of glass door and 2 nos. of steel door with adjustable shelves. the door shall be operated with aesthetically appealing snap fit abs plastic handle and concealed crank hinge. the glass shall be used 4mm thick clear. the shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. uniformly distributed load capacity of each shelf shall be 40 kg maximum. each rack shall be provided with stiffener at bottom for strength. the entire body panel, shelf shall be made of high yield strength 0.8mm thick crca sheet of grade ‘d’ confirming to is: 513. to protect the ball from kicks, abrasion and serve as a decorative moulding skirting shall be provided at the bottom. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40 60μ thick. 42 boq item 42 ( size as per layout ) lab table wall side ( 4575 x 750 x 900 mm ) overall size 4775mm l x 750mm d x 900mm h made up of c frame understructure. all sheet metal items shall be of crca as per is 513:1994. c frame made of rectangular pipe with cross section of 60mm x 30mm & 2 mm thick with feet tolerance of 5mm to +20mm & skirting at bottom side. horizontal members to connect c frame shall be made of rectangular pipes of crca ms 2mm thick of pipe dimension 60 x 30 x 2 mm. side cover panels, back panels should be made from crca ms panels of 0.8mm thick. electrical trunking having electrical switches 16a & 32 sockets 16a with six module plates. welded understorage cabinet with intersection of vertical and horizontal members having provision to be relocated anywhere easily as an independent unit. doors should be assembled with hinge assembly. intermediate horizontal channels should be provided between door and drawer. shelf should bebend panel with 20mm height. single piece drawer tray supported on lh and rh ball slide to be provided. knee space panel shall be in 22 gauge construction. 3understorages of size 600mm w x 530mm d x 635mm h should be supplied having 1 drawer & 2 shutters. thickness of storage unit lh / rh panels, shutter front, bottom panel, top front, drawer separator, alignement channel, back panel, shutter cover, fr. rack strip, top cover should be of 0.8mm thick. handle polypropylene recessed type. lock facility with 180° and 10 lever cam lock mechanism ( except for sink and corner unit ) . shutter should be of single type construction. ball slide: 500mm length ( required only for drawer unit ) . shutter should have provision of roller catch. worktop should be 19mm ( + / 2mm ) thick black granite worktop with exposed edges chamfered. all steel frame work is should be pretreated with superior epoxy powder coated finish. 2 43 boq item 43 ( size as per layout ) lab table with alternate understorage electrical fitting , reagent rack with sink overall size 3560mm l x 1500mm d x 900mm h made up of c frame understructure. all sheet metal items shall be of crca as per is 513:1994. c frame made of rectangular pipe with cross section of 60mm x 30mm & 2 mm thick with feet tolerance of 5mm to +20mm & skirting at bottom side. horizontal members to connect c frame shall be made of rectangular pipes of crca ms 2mm thick of pipe dimension 60 x 30 x 2 mm. side cover panels, back panels should be made from crca ms panels of 1.0mm thick. fixed type crca double sided ms reagent shelves consisting of 2 stage horizontal storage shelves having electrical switches 16a & 24 sockets 16a with six module plates. welded understorage cabinet with intersection of vertical and horizontal members having provision to be relocated anywhere easily as an independent unit. doors should be assembled with hinge assembly. intermediate horizontal channels should be provided between door and drawer. shelf should be bend panel with 20mm height. single piece drawer tray supported on lh and rh ball slide to be provided. knee space panel shall be in 22 gauge construction. 4 understorages of size 600mm w x 530mm d x 635mm h should be supplied. 2 having 1 drawer & 2 shutters and six having only 2 shutters. thickness of storage unit lh / rh panels, shutter front, bottom panel, top front, drawer separator, alignement channel, back panel, shutter cover, fr. rack strip, top cover should be of 0.8mm thick. handle polypropylene recessed type. lock facility with 180° and 10 lever cam lock mechanism ( except for sink and corner 503624 unit ) . shutter should be of single type construction. ball slide: 500mm length ( required only for drawer unit ) . shutter should have provision of roller catch. worktop should be 19mm ( + / 2mm ) thick black granite worktop with exposed edges chamfered. 2 pp sink of size 490mm x 405mm & depth 200mm. bowl size 430 mm x 350mm. all steel frame work is should be pre treated with superior epoxy powder coated finish. 1 boq item 44 microphone sytem : chairman supplying and placing microphone sytem : chairman appart from above delegate unit functions it also has priority switch with led when priority switch is pressed a tone is generated to seek attention and mute the active de;egate mics , highly sensitive and unidirectional condensor microphone provided with diffused led housing the built in speaker in each unit provides clear and crisp sound reinforcement the outputlevel of the speaker can be adjusted through voloume control each microphone has talk switch and talk led which flickers to indicate 2 2 boq item 45 microphone sytem : deligate supplying and placing microphone sytem : deligate highly sensitive and unidirectional condensor microphone provided with diffused led housing the built in speaker in each unit provides clear and crisp sound reinforcement the outputlevel of the speaker can be adjusted through voloume control each microphone has talk switch and talk led which flickers to indicate 23 3 boq item 46 microphone sytem : chairman supplying and placing microphone sytem : chairman appart from above delegate unit functions it also has priority switch with led when priority switch is pressed a tone is generated to seek attention and mute the active de;egate mics , highly sensitive and unidirectional condensor microphone provided with diffused led housing the built in speaker in each unit provides clear and crisp sound reinforcement the outputlevel of the speaker can be adjusted through voloume control each microphone has talk switch and talk led which flickers to indicate 4 4 boq item 47 microphone sytem : deligate supplying and placing microphone sytem : deligate highly sensitive and unidirectional condensor microphone provided with diffused led housing the built in speaker in each unit provides clear and crisp sound reinforcement the outputlevel of the speaker can be adjusted through voloume control each microphone has talk switch and talk led which flickers to indicate 5 boq item 48 microphone sytem : supplying and placing microphone sytem : controller for confrence systems 3 6 boq item 49 microphone sytem supplying and placing microphone sytem :patching cords and installation , testing and commisioning of full systems 3 7 boq item 50 display pannel led hd smart tv 42 inches supplying and placing led hd smart tv 42 inches, hdr enabled displays will expand the contrast ratio and colour space to offer a more realistic and natural image closer to the way your eyes actually see the real world. deep blacks are combined with very bright highlights to produce a level of reality not previously possible 3 8 boq item 51 display pannel led hd smart tv 65 inches supplying and placing led hd smart tv 65 inches, display pannel led hd smart tv 65 inches 65″ 4k uhd ( 3840 x 2160 ) resolution android led display with built in 2.4 ghz wifi, 1.1 ghz built in quad core processor, 2 gb ddr3 ram, 16 gb memory, built in triple core mali 600 mhz gpu 1 9 boq item 52 interactive screen for traning room 55″ 4k uhd ( 3840 x 2160 ) resolution interactive screen for traning room 55″ 4k uhd ( 3840 x 2160 ) resolution android led display with built in 2.4 ghz wifi, 1.1 ghz built in quad core processor, 2 gb ddr3 ram, 16 gb memory, built in triple core mali 600 mhz gpu, with hdr 10, dolby audio, built in wifi and cromecast, hdmi cec, hdmi arc, built in bluetooth ver.4, 20w built in speakers, hdmi 2.0 x 3, av x 1, usb 2.0 x 1, rj45 x 1 ( network connectivity only ) , headphone out x 1, spdif out x 1 boq item 53 roller blinds providing & supply of roller fabric designer blinds with head rail vista / vl / marvel or equivalent make & installation for window as per the approved design all complete as per drawing , specification and direction as approved by the arthitect / engineer in charge . 3.5x2.5 in squre meter 1 9.00 2 boq item 54 roller blinds providing & supply of roller fabric designer blinds with head rail vista / vl / vista / vl / marvel or equivalent make & installation for window as per the approved design all complete as per drawing , specification and direction as approved by the arthitect / engineer in charge .4x2.5 in squre meter 5.00 3 boq item 55 roller blinds providing & supply of roller fabric designer blinds with head rail vista / vl / vista / vl / marvel or equivalent make & installation for window as per the approved design all complete as per drawing , specification and direction as approved by the arthitect / engineer in charge .2x2.5 in squre meter 4.00 4 boq item 56 roller blinds providing & supply of roller fabric designer blinds with head rail vista / vl / make & installation for window as per the approved design all complete as per drawing , specification and direction as approved by the arthitect / engineer in charge .4.5x2.5 in squre meter 1 3.00 5 boq item 57 roller blinds providing & supply of roller fabric designer blinds with head rail vista / vl / vista / vl / marvel or equivalent make & installation for window as per the approved design all complete as per drawing , specification and direction as approved by the arthitect / engineer in charge .6x2.5 in squre meter 2.00 6 boq item 58 roller blinds providing & supply of roller fabric designer blinds with head rail vista / vl / vista / vl / marvel or equivalent make & installation for window as per the approved design all complete as per drawing , specification and direction as approved by the arthitect / engineer in charge .3x2.5 in squre meter 1 0.00 7 boq item 59 roller blinds providing & supply of roller fabric designer blinds with head rail vista / vl / vista / vl / marvel or equivalent make & installation for window as per the approved design all complete as per drawing , specification and direction as approved by the arthitect / engineer in charge .2.5x2.5 in squre meter 2.00 8 boq item 60 roller blinds providing & supply of roller fabric designer blinds with head rail vista / vl / vista / vl / marvel or equivalent make & installation for window as per the approved design all complete as per drawing , specification and direction as approved by the arthitect / engineer in charge . 1x2.5 in squre meter 9 boq item 61 roller blinds providing & supply of roller fabric designer blinds with head rail vista / vl / vista / vl / marvel or equivalent make & installation for window as per the approved design all complete as per drawing , specification and direction as approved by the arthitect / engineer in charge .11x2.5 in squre meter 1.00 10 boq item 62 roller blinds providing & supply of roller fabric designer blinds with head rail vista / vl / vista / vl / marvel or equivalent make & installation for window as per the approved design all complete as per drawing , specification and direction as approved by the arthitect / engineer in charge .5x2.5 in squre meter 2.00 11 boq item 63 roller blinds providing & supply of roller fabric designer blinds with head rail vista / vl / vista / vl / marvel or equivalent make & installation for window as per the approved design all complete as per drawing , specification and direction as approved by the arthitect / engineer in charge . 10.5x2.5 in squre meter 1.00 12 boq item 64 wooden finish metal curtain rod for door providing &supply of wooden finish metal curtain rod for door as per the approved desgin all complete as per drawing , specification and direction as approved by the architect / engineer in charge 1.2x2.5 in running meter 40.00 13 boq item 65 wooden finish metal curtain rod for door providing &supply of wooden finish metal curtain rod for door as per the approved desgin all complete as per drawing , specification and direction as approved by the architect / engineer in charge 1x2.5 in running meter 1.00 14 boq item 66 wooden finish metal curtain rod for door providing &supply of wooden finish metal curtain rod for door as per the approved desgin all complete as per drawing , specification and direction as approved by the architect / engineer in charge 1.8x2.5 in running meter 9.00 15 boq item 67 door curtain providing & supply of door curtain as per the approved design all complete as per drawing , specification and direction as approved by the architect / engineer in charge...

Indian Army - Uttar Pradesh

32558954 bids are invited for ceiling fan , false ceiling board , ceilling aluminum chanel 2ft , led lights 12 wt , switch socket , 15 amp socket , pvc copper wire , obd paint white , obd paint o , synthetic enamel paint , turpentine oil , steel door frame , ply wood ,sliding bolt , door handle , tower bolt , hinges , windowglass , glass putty , asbestos sheet , window wire mesh ,nails , paint brush , paint roller total quantity : 146...

Northern Railway - Uttar Pradesh

32121528 auction sale of condemned and unserviceable released / abandoned staff quartersloc abandoned quarter no. l 59 ( a to z & a1 to n1, all type i, 40 nos & quarter no. l 58 ( a to x ) , all type i, 24 nos similar quarters of fateh ali colony & quarter no. e 7 ( a to o ) , e 9 ( a to o ) all type ii, 45 nos similar quarters of punjab nagar colony in the section of sse w loco under aden hq lko, total 109 units, with approximate 1 released bricks 1111380 nos2 scrap packing wood 8.55 mt3 scrap ferrous melting ?a ) steel door 9.951 mtb ) ms rod 16 mm dia.@ 1.58kg / m and 20 mm dia @ 2.47 kg / m 2.819 mtc ) islb 250 @27.9kg / m 31.95 mtd ) islb 150 @14.20 kg / m 2.763 mte ) islb 75 @6.1 kg / m 2.99 mtf ) ms angle 65x65x8mm@ 7.7kg / m 1.178 mtg ) ismc 225 @25.90kg / m 4.449 mth ) ismc 250@30.40kg / m 0.35 mti ) ms angle 60x60x5mm@ 4.50kg / m and ms angle 50x50x4mm@3.0kg / m 0.3 mtj ) ms flat 50x6mm@ 2.4kg / m 0.16 mtk ) ms angle 50x50x4mm@ 3.0kg / m 0.116 mtl ) ms flat 40x6mm@ 1.9kg / m 0.0445 mtm ) ms plate 6.0 mm thick @ 47.1 kg / m 0.0168 mt4 rail 75r@ 37.13kg / m 40.184 mt...

Public Works Department - Uttar Pradesh

32108347 maintenance work in government inter college, sector 12, noida, gautam budh nagar for project decoration under government secondary schools ( boys / girls ) scheme in district gautambudhnagar. 1 finishing with deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers specifications :two or more coats applied on walls @ 1.25 ltr / 10 sqm over and including one coat of special primer applied @ 0.75 ltr / 10 sqm. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / i dsr no. 13.48.1 2 provinding & applaying white cement based putty of average theckness 1 mm, of approved brand and manufacturer, over the plastered wall surface to propare the surface even and smooth complete. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / idsr 13.80 3 finishing walls with water proofing cement paint of required shade: old work ( one or more coats @ 2.20 kg / 10sqm ) complete. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / idsr. 13.109.2 4 painting with synthetic enamel paint of approved brand and manufacture: 13:99:1 one or more coats on old work. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / idsr 13.99 5 removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / i dsr 13.91 6 12 mm cement plaster of mix :1:4 ( 1 cement: 4 coarse sand. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / idsr no 13.4.1 7 dismantling old plaster or skirting raking out joints and cleaning thesurface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / i as per dsr each. 15.56 8 providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc., complete. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / ias per dsr item no. 11.41 9 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. including supply of all materials, labour, tools and plants etc. excluding gst as per e / i. complete.as per dsr each. 8.31 10 dismantling tile work in floors and wall laid in cement mortar including stacking material within 50 metres lead. for thickness of tiles 10 mm to 25 mm. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / idsr no. 15.23.1 sqm 54.85 11 providing and laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third and fifth course of blown bitumen 85 / 25 or 90 / 15 conforming to is : 702 applied hot @ 1.45, 1.20 and 1.45 kg per square metre of area respectively, second and fourth courses of roofing felt type 3 grade i conforming to is : 1322 ( hessian based self finished bitumen felt ) , sixth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per sqm including preparation of surface but excluding grading, complete. including suppply of all materials, labour, tools, & plants etc. required for proper completion of the work. excluding gst as per e / i. as per dsr no. 22.9 12 providing and placing on terrace ( at all floor levels ) polyethylene water storage tank, isi : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank and including supply of all materials, labour and t&p etc.but excluding g.s.t.required for proper completion of work..dsr 2018 18.48 13 prividing and fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / i. as per dsr 10.30.1 14 m 150 brick work in cement mortar in proportion of 1:4 ( 1cement and 4 coarse sand ) in foundation & plinthincluding all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / i sor no. 19 / 20 15 providing and fixing isi marked flush door shutters conforming to is :2202 ( part i ) eachn decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including isi marked stainless steel butt hinges with necessary screwsincluding all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / i. as per dsr each. 9.21.1 16 providing and fixing double scaffolding system ( cup lock type ) on the exterior side, up to seven story height made with 40 mm dia m.s. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with m.s. tubes, m.s. tube challies, m.s. clamps and m.s. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .the scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of engineerin charge .the elevational area of the scaffolding shall be measured for payment purpose .the payment will be made once irrespective of duration of scaffolding. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / idsr no.24.2 17 dismantling of flushing cistern of all types ( c.i. / pvc / vitrious china ) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / i dsr no. 15.52 18 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: white vitreous china wash basin size 630x450 mm with a pair of 15 mm c.p. brass pillar taps. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / idsr no. 17.7.1 19 providing and fixing mirror of superior glass ( of approved quality ) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :circular shape 450 mm dia. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / i dsr no 17.32.1 20 providing and fixing p.v.c. low level flushing cistern with manually controlled device ( handle lever ) conforming to is : 7231, with all fittings and fixtures complete. 10 litre capacity white. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst dsr no. 17.19.1 21 providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and c.p. brass spreaders with brass unions and g.i clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :one urinal basin with 5 litre white p.v.c. automaticflushing cistern dsr. each. 17.4.1 22 providing and fixing g.i. pipes complete with g.i. fittings including trenching and refilling etc. 20 mm dia nominal bore including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst dsr no. 18.12.2 23 providing and fixing white vitreous china pedestal type water closet ( european type ) with seat and lid, 10 litre low level white vitreous china flushing cistern & c.p. flush bend with fittings & c.i.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required and including supply of all materials, labour and t&p etc.but excluding g.s.t.required for proper completion of work. w.c. pan with isi marked white solid plastic seat and lid. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / idsr 17.3.1 24 providing and fixing c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931, 15mm eachminal boreincluding all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / i as per dsr 18.53.1 25 providing and fixing 600x450 mm beveled edge mirror of superior glass ( of approved quality ) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / i dsr 2018 17.31 26 flexible ( coil shaped ) pvc waste pipe for sink and wash basin 40 mm dia with length eacht less than 700 mm i / cpvc waste fittings. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / i. as per dsr each 17.28.2.2 27 providing and fixing c.p. brass long body bib cock of approved quality confirming to is standered and weighing eacht lass than 690 gm. including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / i dsr 18.51.115 mm eachminal bore. 28 providing and fixing c.p. brass bib cock of approved quality confirming to si.each:8931 including all taxes, material, t&p, machinary, royalty, labour cess all taxes complete. excluding gst as per e / idsr 18.49.1...

Department Of Technical Education - Uttar Pradesh

31677267 bids are invited for boqauto extension if any seller submits price in last 15 minutes, the rawill be auto extended by 15 minutes. ( for anunlimited time ) average turn over of last 3 years 1 lakh ( s ) mse exemption for turnover yesstartup exemption for turnover yes1. if the bidder is a micro or small enterprise as per latest definitions under msme rules, the biddershall be exempted from the requirement of bidder turnover criteria and total quantity : 1 1 pvc gitti ( 2 ) 2 self drilling screw ( 2” ) 3 curtain hook 4 left closer ( for clock wise door ) 5 butt hings ss ( 5” ) 6 jet spray 7 toilet seat covers 8 agmeco cast brass pillar taps 9 gate valve ( 3 / 4” ) 10 wash basins with flat back and oval 11 stainless steel connection pipewith nuts 450 mm 12 wash basin having push type tap 13 aluminium tower ( 8” ) 14 slotted raised countersunk head wood 15 flush system 10 ltr. 16 wash basin along with waste pipe 17 steel door handle 6 18 steel door handle nut & bolt ( length 150 mm and dia3 / 8 ) 19 connection pipe pvc ( 18” ) 20 cast brass pillar taps ( 2 in 1 ) 21 angle stop valve 15 mm 22 slotted raise dcounter sunk head wood screws ( 2” ) 23 brass hexagon hexreducing nipple 1 / 2 inch 24 brass hexagon hexreducing ( 15 mm x 65 mm ( 2.5” ) 25 ball valve ( cpvc 1” ) 26 brass splitwedge gate valve ( 25 mm ) 27 elbow 90° ( brass ) ( upvc 25 mm ) 28 female thread socketpipes fittings 25 mm ( upvc 25 mm ) 29 pvc elbow pipe fitting ( 1 / 2” ) 30 upvc equal tees ( 1” ) for portable water supplies 31 bathroom hand shower cast 32 centrifugal self priming monoblock pump ( 1 hp ) 33 multitec chrome vanadium steel combination plier insulated pliers 34 round m 4 electricians screw drivers ( 3.5x0.5mm ) 35 pvc connection pipe with nuts 450 mm 36 digital electrician tool kitupto 200 ma 37 pvc solvent 250ml 38 wastehole 125 mm 39 waste fittings for size 50 mm 40 m seal ( 1kg pack ) 41 plug steel pipes fitting ( 15 mm ) 42 plug steel pipes fitting ( 25 mm ) 43 plug steel pipes fitting ( 20 mm ) 44 union pipe fittingpvc 1 / 2 inch 45 iron elbowpipe fitting 1” 46 gi half coupling 1 / 2 47 ( aluminium slideing ladder 20ft ( heavy duty ) 48 nylons double sided polytetrauoroethylene ptfe thread sealing tape 49 steel square aperture wire mesh fabric or cloth ( per kg ) 50 iron detachable joints ( joint for pvc pipe ) 51 angle cutter ( 900 watt. ) 52 gi union 20mm 53 pvc elbow pipe 1 inch 54 d joint 6 inch 55 saddle 6 inch 56 j.i. pipe rinch 14 inch 57 pipe rinch 18 inch ( adjustable wrench tool ) 58 rinch 14x15mm 59 span tool 21 / 23 ( taparia 18 21x23cm ) 60 saw ( hand ) 61 hammer ( 1 kg ) 62 triangle file 63 screw driver set 64 glendar cutter machine...

Public Works Department - Uttar Pradesh

31458617 bids are invited for putty glass , aluminium door hndle 6 inch , looking mirror with polish , s s screw 35 x 5 100 nos per pkt , pillar cock prayag ptmt , bib cock prayag ptmt , angle valve prayag ptmt , cotton thread 6 nos per pkt , fastner wash besin 4 , connection washer pvc 100 nos , pvc connection 18 , pvc connection 24 , pvc connection 36 , pvc sheet 2mm , cpvc pipe 3 4 3m lenth , cpvc pipe 1 3m lenth , ball cock prayag complete ptmt , cistern siphon for 1 piece seat , cp pillar cock with brass spindle 15mm dia , aluminium beading , pvc cistern parryware , window glass 5mm 1 05 x 0.68 mt , window glass 5mm 1.05 x 0.66 mt , window glass 5mm 0.62 x 0.66 mt , window glass 5mm 0.68 x 0.62 mt , window glass 5mm 112 x 98 cm , plain glass 90 x 45 cm , bib cock long body prayag ptmt , china ware sink 24 x 18 , white cement 1kg per pkt , nipple gi 2 x half , nipple gi 3 x half , nipple gi 4 x half , hexa nipple gi 1 , socket 1 gi , union 1 gi , union 2 gi , union 3 4 gi , union cpvc 20mm dia , brass elbow cpvc20mm dia , elbow plain cpvc 20mm dia , m tee cpvc 20mmx15mm dia , plain tee 1 cpvc , plain socket 1 cpvc , ball valve 1 cpvc , ball valve 3 4 inch cpvc , plug pvc 15mm dia , camode sheet complete cera , glass self 600x130 with cp guard rail , towel rod 600mm long , cp bib cock heavy quality 15mm dia , cp angle valve two way heavy quality 15mm dia , cp pillar cock swan neck 15mm dia , wash besin bracket , cp shop dish , cp hand shower with lead , cp jet sprey complete isi mark including i mtr pipe , gi socket 1 2 , gi long screw 1b2 inch , screw steel 2inch 250 no per pk , screw steel 19 x 8 1000 no per pkt , screw steel 25 x 8 550 no per pkt , teflon tap , m seal 100gm per pkt , window lock , aluminiun sliding bolt 10 inch long 16mm dia , door handle 6 inch aluminium , cp bib cock two way heavy quality 15mm dia , cp angle valve heavy quality 15mm dia , round lock godrej for cup board , cp waste jali for wash besin , cp lattu curtain , cp towel ring , cp urinal spreader , pvc gulli 100 nos per pkt , cp wall to wall curtain bracket , cp curtain bracket , door closer godrej , binding wire , chapka kunda 4 inh , pvc waste pipe , pvc tap plasto , pvc angle valve plasto , wheel base for chair , bag for labour tools , screw driver 12 inch , screw driver 6 inch , plas player , hamer 300 gm mild steel , gait repair welder , garari for sliding channel , rubber thin for glass fixing , haidle section aluminium 2 inch x1 inch , section bottom aluminium 4x2 , screw 1 inch steel , door stoper aluminium , pvc waste jali prayag ptmt , prayag ball cockcomplete , nahani trap ci 4 inch x 3 inch , computer repair , door chawkhat 100 x 65 mm single rebate , cistern handle , maruti lock , window glass 0a60 x0a65 mtr , cp hand shower complete with 1a50m flixble tube , cpvc spreader , light cable 1mm for drill machine , light plug 16 amp , gi plug 1b2 inch , gi plug 3b4 inch , gi plug 1 inch , steel jali double hole 4 inch , steel jali single hole 4 inch , steel jali plain 4 inch , steel jali urinal , tap short body , door slider 1 set , l bihari kabja , white glazed earthen ware urinal basin , hammer bit 8mm , hammer bit 10mm , cilip 3b4 inch , solation 50gm , steel bracket for self , wash basin cera 550x400 , waste jali cut , coupling pvc dia 11b4 inch , godrej lock square for cup board , pvc cistern cera with all fitting , sheet cover lead for commode , brass gate valve 2 inch...

Technical Education Board - Uttar Pradesh

30620027 bids are invited for pvc gitti ( 2 ) as defined in specification document , self drilling screw ( 2” ) as defined in specification document , curtain hook as defined in specification document , left closer ( for clock wise door ) as defined in specification document , butt hings ss ( 5” ) as defined in specification document , jet spray as defined in specification document , toilet seat covers as defined in specification document , agmeco cast brass pillar taps as defined in specification document , gate valve ( 3 / 4” ) as defined in specification document , wash basins with flat back and oval as defined in specification document , stainless steel connection pipewith nuts450 mm as defined in specification document , wash basin having push type tap as defined in specification document , aluminium tower ( 8” ) as defined in specification document , slotted raised countersunk head wood as defined in specification document , flush system 10 ltr. as defined in specification document , wash basin along with waste pipe as defined in specification document , steel door handle 6 as defined in specification document , steel door handle nut & bolt ( length 150 mm and dia3 / 8 ) as defined in specification document , connection pipe pvc ( 18” ) as defined in specification document , cast brass pillar taps ( 2 in 1 ) as defined in specification document , angle stop valve 15 mm as defined in specification document , slotted raise dcounter sunk head wood screws ( 2” ) as defined in specification document , brass hexagon hexreducing nipple 1 / 2 inch as defined in specification document , brass hexagon hexreducing ( 15 mm x 65 mm ( 2.5” ) as defined in specification document , ball valve ( cpvc 1” ) as defined in specification document , brass splitwedge gate valve ( 25 mm ) as defined in specification document , elbow 90° ( brass ) ( upvc 25 mm ) as defined in specification document , female thread socketpipes fittings 25 mm ( upvc 25 mm ) as defined in specification document , pvc elbow pipe fitting ( 1 / 2” ) as defined in specification document , upvc equal tees ( 1” ) for portable water supplies as defined in specification document , bathroom hand shower cast as defined in specification document , centrifugal selfpriming monoblock pump ( 1 hp ) as defined in specification document , multitec chrome vanadium steel combination plier insulated pliers as defined in specification document , round m 4 electricians screw drivers ( 3.5x0.5mm ) as defined in specification document , pvc connection pipe with nuts 450 mm as defined in specification document , digital electrician tool kitupto 200 ma as defined in specification document , pvc solvent 250ml as defined in specification document , wastehole 125 mm as defined in specification document , waste fittings for size 50 mm as defined in specification document , m seal ( 1kg pack ) as defined in specification document , plug steel pipes fitting ( 15 mm ) as defined in specification document , plug steel pipes fitting ( 25 mm ) as defined in specification document , plug steel pipes fitting ( 20 mm ) as defined in specification document , union pipe fittingpvc 1 / 2 inch as defined in specification document , iron elbowpipe fitting 1” as defined in specification document , gi half coupling 1 / 2 as defined in specification document , ( aluminium slideing ladder 20ft ( heavy duty ) as defined in specification document , nylons double sided polytetrauoroethylene ptfe thread sealing tape as defined in specification document , steel square aperture wire mesh fabric or cloth ( per kg ) as defined in specification document , iron detachable joints ( joint for pvc pipe ) as defined in specification document , angle cutter ( 900 watt. ) as defined in specification document , gi union 20mm as defined in specification document , pvc elbow pipe 1 inch as defined in specification document , d joint 6 inch as defined in specification document , saddle 6 inch as defined in specification document , j.i. pipe rinch 14 inch as defined in specification document , pipe rinch 18 inch ( adjustable wrench tool ) as defined in specification document , rinch 14x15mm as defined in specification document , span tool 21 / 23 ( taparia 18 21x23cm ) as defined in specification document , saw ( hand ) as defined in specification document , hammer ( 1 kg ) as defined in specification document , triangle file as defined in specification document , screw driver set as defined in specification document , glendar cutter machine as defined in specification document total quantity : 1...

Department Of Agriculture - Uttar Pradesh

30590726 bids are invited for foh speaker 2way compositefoh speakerhaving 15”woofer, 2”voicecoil neodymium compressiondriver, equippedwith internalpassive crossover switchable tobiamp, rotatablecoverage pattern90°x 50°, 98dbsensitivity and 132dbmax spl.600watt continuous powerhandling , nominalimpedance8 o, freqresponse 60—17000 hzmadeof highimpactinjectionmoulded polypropylene structural foam, enclosure has locations for 5 single studattachmentplates and 10 forged steel eyebolts 2 on top, 2 on bottom, 2 on side, and 4 on rear of enclosure. , amplifier heavy duty high performance amplifier, class h design. distortion less than 1 percent maximumpower2 x 1200 wattsat 4 ohms, slew rate 30 v / micro sec, cross talk < 75 db, freqresponse 10 to 40000 hz. balanced input impedance 20 k ohms. s / n ratio 110 db.unit has 3 stage front torearfansfor coolingand has complete protection package forhigh temperature, dc, hf&back emf, unitisequippedwithaudio , peakcurrent& inrushcurrent , monitor poweredspeaker sitcofstage monitor poweredspeakerhavinga12woofer type:full range, two way, wedges woofer size: 304.8 mm ( 12 ) , nominal impedance: 8 o, power rating: 1000 w frequencyresponse ( 10db ) :50 20000hzinternalmax. spl / 1m ( calc ) :126 db. , commercial poweramplifier commercial poweramplifier having 2channels andgiving 450 watt power @ 4 ohms, slew rate 28at 1khz / v / ?s, freqresponse 10 40000 hz at 1db , inputimpedance > 20k ohms. bridge mono mode power is 900 wattat 8ohms amplifier gain 34.3db .three stage fronttorearfanswithcomplete protection package. , driver protectedcircuit 2wayfullrange 200 wattspeakerfullyweatherizeddriver protectedcircuit, trapezoidalshape, freqresponse : 48to20000 hz maxspl 123 db, longtermpowerhandling200 wattslf transducer8”, throat diameter1” and nominalimpedance8ohms equippedwithfourpindetach speak on connectors , sound cabinet speaker. bosch 30 watt premium sound cabinet speaker. , booster amplifier booster amplifier 120 watt, make. , mixer 24 channel mixer, make . , microphone gooseneck microphonecondenser typeunidirectionalwith flexiblestem, phantompowered, voltagerange12 48 volts, sensitivity 2.5 mv / pascal, freq 100 to 16000 hz, outputimpedance <200 ohms. for podium , microphone ( 2 ) gooseneck microphonecondenser typeunidirectionalwith flexiblestem, with on off switch and base , unidirectional mike car diode hand held wired unidirectional mike for general purpose, freq 80 to 12000 hz, sensitivity 1.7 mv / pascal, rugged body in dark grey finish. , loudspeaker dsp2in 6outdigital signal processor for loudspeaker management & optimization, unithas usbportfor advanceediting andcontrol, accurateinputmeasuringassurespropergain staging, rs232port for master slave connection, built in uniquedelay adjustment, a / d conversion 24 bitsigma deltasamplerate 48 khz & internal processing 32 bitfloating, outputimpedance 50 ohms, freq response10to22000hz, dynamic range111dbunweighted. , cordless handheldmicrophone cordless handheldmicrophone, fixed frequencycircuitfor stability and effortless frequency setup, advanced true diversity technology, frequencyrange480–934mhz, sensitivity8 dbµv at s / n > 80 db, s / n ratio > 106db ( a, frequency response 50 hz – 18 khz, handheld transmitter with receiver. , cordless lapel microphone cordless lapel microphone, fixed frequency circuit for stability and effortless frequency setup, advanced true diversity technology, frequency range 480 – 934 mhz, sensitivity 8 dbµv at s / n>80db, s / nratio>106db ( a, frequencyresponse50hz–18khz, body packtransmitterwithreceiver db, s / nratio>106db ( a, frequencyresponse50hz–18khz, , full floor full floor stand for microphone. , half desk half desk stand for microphone. , microphone lead microphone lead 15 mtr. with xlr connector at both end. , audio audio aux audio lead 3.5mm connector 15 mtr. , microphone cable supply and laying of microphone cable for powered speaker and microphone. , flexible speaker layingofflexible speaker cable 2.5sq mm 2core copper pvcsleeved , rack equipmentrack of 32uheight space, front andrear lockable door, front door transparent acrylic, and rear powder coated steel door with cooling fan, cassatas power socketpointandmcbprotected, completeinallrespect. , speaker clamp speaker clamp for in hall and monitor speaker. , speaker stand speaker stand for foh speaker. , patch cable patch cable, av face plate & connector , installation testing commissioning & installation charges , copper plate earthling copper plate earthling 600x600x6 mm with cabling, complete in all respect total quantity : 1...

Military Engineer Services - Uttar Pradesh

30209371 certain sanctioned work under age br i ge faizabad certain sanctioned work under age br i ge faizabad 1 dismantling floor, hearth or wall tiling including cm bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises , complete all as specified. 2 taking down chowkats or framesnexc1.5 sqm each ( without taking off shutters from the frames ) , complete all as specified. 3 taking down cement plaster from brick walls including raking out joints, hacking for key, scrubbing down with water to receive plaster removal of rubbish off the premises etc., complete all as specified. 4 m&l non skid ceramic coloured tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles and including 15mm thick screed bed in cm 1:6 , complete all as specified. 5 m&l glazed ceramic coloured tiles in vertical surface 350x250x 7 mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to matchwith the shade of tiles and including 10mm thick rendering in cm 1:3 to receive wall tiles , complete all as specified. 6 demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar, complete all as specified. 7 m & l 5mm thick rendering on fair faces of brick work or concrete surface in cm 1:3 as in ceiling to be finished even and smooth with out using extra cement, complete all as specified.. 8 m & l 10mm thick rendering on fair faces of brick work or concrete surface in cm 1:4 to be finished even and smooth withoutusing extra cement , complete all as specified.. 9 cutting chasesin brick walls , pinning in, making good to facings where required and pointing in cm 1 : 3 to ends, or edges of landings steps, cills, and cutting chases for concealed water tubing or conduit wiring etc and making good cutting n exc 10 cm girth , complete all as specified. 10 m&l for form work to sides and soffit of floor or roof beam, beam haunchings, girders, bressummers lintels, cantilevers, shelves including supports, overhangings etc., also splays between floor and beam as in fair finished, complete all as specified. 11 s & ftmt steelbars 6 to 8 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including ms wire annealed not less than 0.9 mm dia , complete all as specified. 12 m & lrcc 1 : 2 : 4 type b1 ( 20 mm graded crushed stone aggregate ) as in slabs supported on walls beam and colums in floors, roofs, landings, deck slabs and shelves and the like , complete all as specified. ( formwork and reinforcement shal be measured and paid separately ) 13 m&lfor 20mm thick machine cut granite stone, in skirting / dado laid over cement screed and jointed with gray cement slurry and pointed white cement with admixture of pigment to match the shade of granite stone including grinding and polishing and including 15mm thick screed bed in cm 1:6 , complete all as specified. 14 rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations , complete all as specified. 15 s&f wash hand basin of size 61x46x15mm and including sensor pillar tap and bottle trap complete all as specified .cat no : 91043 & cat no f240005cp or equivalent as approved by ge / 16 s&f10mm thick frosted toughened glass door swing type with 300 mm wide stainless steel handle andincluding floor spring and locking arrangement and necessary fittings, complete all as specified. 17 s&f ewc 500x360x300mm wall mounted water closet and including seat cover white and necessary fitting connection to trap etc., , complete all as specified. 18 s&f concealed neo flush tank 80mm full frame and accessories connetion to iron pipe, complete all as specified. 19 s&f ceramic urinal pot of size 37x39x61cm with with inbiult sensor type connection to iron pipe and waste pipe, complete all as specified. cat no : 60018 or quivalent as approved by ge. 20 s&f rectangular shaped urinal partition with forsted glass partition for urinal of 8mm thickof size 900x450mm and necessary cleats for fixing the glass, complete all as specified. 21 s & f aluminium door in lieu of wooden or steel door / window / ventilator, made out of extruded powder coated aluminium sections, with sliding or openable shutters including frame and necessary jointing cleats, glazing clips, powder coated aluminium snap beading, screws etc completerubber beading and handles including connected items with and including, making goodfor dismantling portion in pcc1:2:4 or cm 1:3 , complete all as specified.note : ( i ) minimum thickness of powder coating shall be 15 micron for windows and 25 microns for doors. 22 s & f aluminium window / ventilator in lieu of wooden or steel window / ventilator, made out of extruded powder coated aluminium sections, with sliding or openable shutters including frame and necessary jointing cleats, glazing clips, powder coated aluminium snap beading, screws etc complete and also including powder coated aluminium fittings such as cobra hinges, butt hinges, tower bolts, star lock, hooks & eyes peg stays, rubber beading and handles including connected items with and including, making goodfor dismantling portion in pcc 1:2:4 or cm 1:3 complete all as specified and directed.note : ( i ) minimum thickness of powder coating shall be 15 micron for windows and 25 microns for doors. 23 s & f sheet glass frosted of ordinary quality 3mm thick in panesnexc 0.5 sqm in each pane, complete all as specified. 24 s&f looking mirror of size 1000x600mm and including stainless steel nut & bolts wirh rubber washer , complete all as specified. 25 s&f towel rail 600mm long chorium plated , complete all as specified. make :cat nof450024cp or equivalent as approved by ge. 26 s&f towel ring chorium plated, complete all as specified.make :cat no f450023cp or equivalent as approved by ge. 27 s&f rain shower rose cp 200mm square rubbit cleaning system , complete all as specified. make :cat no f160041cp or equivalent as approved by ge. 28 s & f 75 mm bore, pvc ( swr ) single socketed rain water pipe in any length with rubber ring joints fixed to walls , complete all as specified. 29 m&l 75mm bore pvc ( swr ) floor trap , plain with grating including jointing with solvent cement , complete all as specified. 30 s& f bib tap two in one chorium plated , complete all as specified.make :cat no f160041cpor equivalent as approved by ge. 31 s& f angle cock chorium plated , complete all as specified.make :cat no f280004cp or equivalent as approved by ge. 32 s&f glass corner with chrome finish shelf of size 9 inch x 9 inch for bathroom , complete all as specified. 33 m & l2nd class hard wood, plain straight, solid chawkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, supplied and fixed, complete all as specified. 34 s & f 30 mm thickflush shutters, solid core construction, with block board core and plywood face panels, commericial type on both sides with decorative faces venner with lipping / frame to match , complete all as specified. 35 s & f 100mm long butt hings cast brass mild steel hinge pin, bright polished and fixed type b 11 medium weight & fixed to chowkats, complete all as specified. 36 s&f 150mm long brass handles, fabricated type polished bright , complete all as specified. 37 s&f 200mm long brass barrel tower bolt, but with extruded section polished bright, complete all as specified. 38 s&f mortice lock vertical type size 100mm brass 2 levers , complete all as specified. 39 m&l for interior wall texture paint match to wall and including making smooth finish , complete all as specified. 40 s&f wall mixer cpfancy type connection to iron pipe , complete all as specified. 41 s & f soap dish cp fancy type with brass screws , complete all as specified. 42 m & l for preparing newly plastered surfaces of ceiling and two coats of oil bound distemper ( smooth finish ) , complete all as specified. 43 m & l preparation of old decorated surfaces of walls including complete removal of existing treatment and applying two coats ofdistemper oil emulsionover 1mm thick wallcare putty complete as specified and directed. 44 m & l for bees wax on previously polished surfaces of any description width or girth including cleaning and preparing the surface , complete all as specified. 45 m&l for preparingold steel surface exc 10 cm in width or girth and applying one coats of synthetic enamel paint, complete all as specified. 46 m & l preparation of old wooden surfacesof any description , not other wise described, over 10cm width or girth including and applyingone coat of synthetic enamel paint, complete all as specified. 47 m & l preparing old decorated surfaces of ceilings and applying two coats of white wash, complete all as specified. 48 s & f steel windows with side hung shutters including projecting hinges with steel handle and steel peg stay, complete with glazing bars, both with and without sash bars dovetailed or welded including painting with one shop coat of zinc chromate primer, complete all as specified. 49 s & f sheet glass of ordinary quality 3.00 mm thick in panesnexc 0.5 sqm in each pane, complete all as specified. 50 s & f anodised aluminium door shutters, swing type aluminium sections weighing 0.55 kg / m including necessary joining cleats, glazing clips, rubber neoprene packing handles 2 nos in each door, hinges, anodised aluminium snap beading screws etc , complete all as specified. 51 s&f double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass other parts made of mild steel heavy duty and fixed , complete all as specified. 52 s&f 500 litres capacity rotational moulded polythene water storage tanks ( cylindrical vertical, with closed top ) , hoisted and fixed in position as specified in ssr part i and directed and including taking down old and kept in store , complete all as specified. 53 s&f 20mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed , complete all as specified. 54 s&f 20mm bore ball valves high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. ( min weight 15mm 142 gms / 20mm 210 gmsfixed to iron pipe , complete all as specified. 55 taking up or down steel tubing and connections, including cleaning for re fixing or removal to store 20 mm bore, complete all as specified. 56 taking up or down steel tubing and connections, including cleaning for re fixing or removal to store 15 mm bore, complete all as specified. 57 s & f 20 mm bore gi tubing medium grade with all fittings and fixed complete to walls or laid in floors, complete all as specified. 58 s & f 15 mm bore gi tubing medium grade with all fittings and fixed complete to walls or laid in floors, complete all as specified. 59 s & f sheet glass tinted of ordinary quality 5.00 mm thick or suitable for aluminium glass shutter in panesexc 0.5 sqm in each pane, complete all as specified. 60 complete removal of existing water proofing treatment upto concrete surface of roof slab of any description and of any thickness including removal of water tanks and replacing in same position, cleaning, wire brushing, watering, removal of debris all as specified and directed. ( a ) 10mm thick screed bed in cm 1: 4 with wpc. ( b ) m&l for applying primer @ 0.50 kg / sqm on prepared surface confirming to is 3384 1965. ( c ) a layer of hot blown bitumen grade 85 / 25 as per is 702 1988 @ 1.2 kg / sqm will be applied over primer. ( d ) laying of app membrane polymeric water proofing membrane 3mm thick and weight not less then 3kg / sqm with non woven polyster reinforcement andbonded completely to the substrate & the overlaps are then scale / fused by flame as per manufacture instruction and laying procudere. the minimum overlaps of 100mm shall be allowed at the ends and sides of strips polymeric membrane. ( e ) applying a layer of blown garde bitumen 85 / 25 @ 1.2 kg / sqm and blinding material such as sand in dry condition @ 0.5 to 1.0 kg / sqm shall be dusted over the bitumen ( f ) toping will be done with pcc tiles 25mm thick laid over 15mm screed bedding in layer of cm 1:4 and jointed & pointed in cm 1:4 linseed oil @ 5% by weight of cement shall be mixed with cm for screed and pointing to the brick tiles. after laying the curing shall be cured with water ponding complete all as specified and directed. 61 surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out in soil and loose soil , complete all as specified. 62 m & l 75 mm thick pcc 1:4:8 type d 2 ( 40 mm gradedcrushed stone aggregate ) as in sub base to floors, complete all as specified. 63 m & l 75 mm thick, plain cement concrete1:3:6, type c 2 ( using 40mm graded crushed stone aggregate ) as in plinth protection / hard standing etc, finishing cement concrete surface even and smooth without using extra cement, complete all as specified. 64 m & l sand filling under floors or in foundations including watering and consolidation, complete all as specified. 65 m & l machine pressed precast coloured concrete interlocking paver block rubber moulded any shape and size of 60mm thickness, m 35 grade conforming to is 15658 2006 with grey cement and pigment , complete all as specified. 66 m & lbrick work with sub class b bricks straight or curved on plan exc 6 m mean radius built incm1 : 6 , complete all as specified. 67 s & ftmt steel bars 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including ms wire annealed not less than 0.9 mm dia , complete all as specified. 68 m & l pcc 1 : 3 : 6type c 1 ( 20 mm graded crushed stone aggregate ) in lintel upto 1.5m clear span, cill, steps, seismic and other similiar bands, plinth courses, string courses, laacing courses parapets and railings upto 60 cm in height, bed plates, copings, kerbs, etc. water troughs and the like includind weathering, slightly rounded or chamfered angles and throating , complete all as specified. 69 taking downcarefully aluminiumpointwiring1.5sq mmof complete, switch socket 5amps& power point etc including switches andmakinggooddisturedsurfacesofwalls / ceilingetc , complete all as specified. 70 m & l point wiring for one light point / fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor, frlspvc insulated unsheathed cable in and including 20 mm dia or higer size pvc concealed conduit and fittings with 1.5 sqmm nominal cross sectional area used as continuous earth wire and connected to earth dolly including metal flush boxes with white cover plate andmaking neccessory electrical connection of modular type switches, sockets, regulators etc , complete all as specified. for one light pointor fanpointcontrolled by one switch . 71 all as per item no. 70 but for one 3 pinsocketoutlet5 ampson same board with other switches 72 all as per item no. 70 but for one 3 pinsocketoutlet5 amps socket outletindependent but belowthe switch board of light pointin the same vertical plane 73 m & l for point wiring with 2.5 sqmm ( nominal cross sectional area ) fr pvc insulated & unsheathed 1100 volts grade multi stranded copper conductor single core cable drawn through and including non metallic rigid pvc conduit / pvc casing caping of adequate size with all fittings and accessories including pvc sunk box with 3mm thick plastic laminated sheet top cover complete including fr pvc insulated & unsheathed single core multistranded copper conductor cable of size 1.5 sqmm green in colour as earth continuity conductor connected to common earth dollyfor one 16 amp socket outlet on independent board. 74 s & f switch piano flush type one way 6 amps , complete all as specified. 75 s&f switch piano, flush type, one way, 16 amps , complete all as specified. 76 s & f socket outlet 5 pin, 6 amp flush type, complete all as specified. 77 s&f socket2 in 1, 3 pin, 5 and 16 amps flush type , complete all as specified. 78 s & f ceiling rose surface bakelite three terminals , complete all as specified. 79 s&f led tube light fitting, 1x20 watt surface and wall mounted decorative ultra slim square profile with extruded polycarbonate, environmental friendly, energy efficient ready to use paclk fitting including provn of twin core multi stranded copper cable of size 1.5 sqmm from ceiling rose to tube light fitting , complete all as specified. 80 s&f led tube light fitting, 1x10 watt surface and wall mounted decorative ultra slim square profile with extruded polycarbonate, environmental friendly, energy efficient ready to use paclk fitting including provn of twin core multi stranded copper cable of size 1.5 sqmm from ceiling rose to tube light fitting , complete all as specified. 81 supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230v, 50 hz, rpm 1200, copper winding of sweep 300mm , complete all as specified. 82 s&f epoxy powder coated mcb, db, double door spn 4 way for mcbs with common bus bar at incoming end of outgoing mcbs grouted / flush to wall , complete all as specified. 83 m & l mcb spn 32 amps c series , 240 volts , complete all as specified. 84 m & l mcbsp 32 amps c series , 240 volts, complete all as specified. 85 s&f led spot light with a focused 36 degree beam angle 7 w, round, 3000k including provn of twin core multi stranded copper cable of size 1.5 sqmm from ceiling rose to tube light fitting , complete all as specified. 86 excavation in trenches, not exceeding 1.5 meter wide and not exceeding 1.5 meter in depth for foundation of poles, stays or for taking out / laying of cables and getting out in soft / loose soil , complete all as specified. 87 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in soft / loose soil, complete all as specified. 88 removing excavated materials ( soil ) n. exc 50m and depositing where directed at a level n.exc 1.5m above the starting point , complete all as specified. 89 m & l for sand cushioning to underground cable with clean dry river sand complete all as specified . note: punned thickness only shall be measured & paid. 90 supply & laying of sub class bbricks locally available best quality laid flat ( length of bricks laid across the length of cable ) in tranches for protection of u / g cable , complete all as specified. 91 supply, laying and testing cable xlpe insulated , screened, pvc bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty ) 1100 volts grade with stranded aluminium conductor of size 16 sq mm 2 core, complete all as specified. 92 supply, testing and fixing of new flood light luminaires led type with c clamps mounting and lm6 pressure die cast housing with high efficiency glass cover system, ip 66, power 120 watts and making necessary electrical connection with suitable size pvc insulated copper multi stranded 1100 volts grade cable with suitable size lugs etc , complete all as specified. 93 m&l earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in to ground ( earth pit ) not less than 2.25 meters deep below gl with top edge of earth plate not less than 1.50 m below ground level, connected to gilead wire of 4 mm dia. ( 7.50 m long ) by means of nuts, bolts and washers, check nuts of gi and protected by the gi pipe light grade 1.5 mm nominal bore ( 7.50 m long ) for earth plead wire, watering pipe light grade of 20 mm nominal bore, 0.63 mm thick ci funnel, wire mesh etc complete including necessary earth work and excavation in any type of soil, pcc 1:2:4 type b1 earth pit and precast rcc cover 50 mm thick dully reinforced with 6 mmdia, ms round bars @ 100 mm c / c both ways, earth testing point, making good to floor complete all as specified....

Iti Ltd - Uttar Pradesh

29993035 labour rate for maintenance of steel door / window / shutter and carrying out welding labour rate for maintenance of steel door window shutter and carrying out welding...

Aligarh Muslim University - Uttar Pradesh

29695616 auction auction of condemned items at department of law 1 balance chainometric analytical 20 2 balance analytical 11 3 metrex rotary vaccum evaporator buchi type 01 4 compressor air ( khosla ) 01 5 orbital model kit 01 6 stabilizer 10 7 viscometer redwood no.1&2 01 8 gas analysis ( orset apparatus ) 01 9 heat convector 02 10 stop clock 11 11 nitrogen gas cylinder 03 12 acetylene gas cylinder 01 13 stirrer ( electric ) 01 14 chair easy 01 15 chair steel revolving 02 16 centrifuge 02 17 ph meter elico / philips 02 18 conductivity meter ( measuring bridge ) 02 19 water bath shaker 01 20 inverter 500 va 01 21 heating mental 03 22 ph meter digital elico 01 23 lubricant tester wheel bearing btl 01 24 spectrophotometer cl 24 01 25 microscope metallurgical student type 01 26 microscope metallurgical student type 01 27 microscope lietz panphot 01 28 microscope metallurgical vertical russian 01 29 ups offline, elnova 01 30 cloud & pour point apparatus 02 31 water stil 02 32 water bath electric 11 33 lpg small gas cylinder 04 & 05 kg 02 34 lpg small gas cylinder 04 & 05 kg 03 35 melting point apparatus ( metrex ) 01 36 balance sartorius analytical electronic 01 37 wall clock 01 38 table steel sunmica top ( size 4 ½ x 2 ½ x 2 ¼ ) 01 39 flame photometer ( systonic ) , type 121 01 40 hot air oven 01 41 inverter microtek 800 va 01 42 digital electrophorus power pack 01 43 scanner canon, model lide110 01 44 laser printer samsung, model no. hl 1610 01 45 laser printer konica minolta, model 1350w 01 46 laser printer hp, model p1007 01 47 columns for shimadzer hplc 48 hplc / tlc sample software, model as30 230vpc 01 49 balance physical 01 50 speaker steelscope 01 51 zeiss spectro colorimeter 01 52 elico naphelometer, model cl 52 01 53 hydrogen gas cylinder 02 54 atomic absorption spectrophotometer, gbc 902 01 55 polymer film making equipment with dry box and three dies, model pf a15 01 56 table office wooden ( two drawer ) 01 57 table steel sunmica top ( one shelf & three drawer ) , size 5 ½’ x 3’ x 2 ½’ 01 58 chair wooden armless 01 59 inverter mocrotek 800 va 01 60 potentiometer with two electrode elico 01 61 centrifuge hand operated machine 01 62 potentiometer digital make ei, model 118b 01 63 cd 60 densitometer / scanner for hplc with accessories 01 64 ph meter pan type 01 65 muffle furnace digital 1000 c 01 66 refrigerator 01 67 exhaust fan 01 68 leitz metallux 2 microscope, germany 01 69 enlarger photographic , model sonnar, size 2b 01 70 flash point apparatus abel’s 01 71 metrex temperature control unit 01 72 nanomat iv ‘camag’ used for hptlc 01 73 nanomat iv accessories used for hptlc 01 74 type writer, godrej 01 75 type writer, remington 01 76 computer p iii 01 77 computer compaq presario note book pentium h 715 01 78 computer ibn / lenova with printer & ups 01 79 computer imaging system 01 80 elico photo electric colorimeter, model cl 20a 01 81 elico spectro colorimeter model cl 23 01 82 ph meter 01 83 almirah with steel doors, size 6 ½’ x 3’ x 1 ½’ 01 84 almirah steel with glass pans, size 6 ½’ x 3’ x 1 ½’...

Uttar Pradesh Projects Corporation Limited - Uttar Pradesh

29628376 balance work for construction of multipurpose seed store and technology dissemination centre, nanauta, saharanpur balance work for construction of multipurpose seed store and technology dissemination centre, nanauta, saharanpur , earth work in exacavation in foundationsin foundations in ordinary soil (loam clay or sand) including lift upto 1.5 m and lead upto 30 mt. & including filling, watering and ramming of excavated earth into the trenches or into the space between building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the e/i upto a distance of 30 mt. from the foundation trenches. , earth work in exacavation in foundationsin foundations main building, septic tank & soak pit in ordinary soil depth from 1.5m to 3.0 m i/c all cost of material,labour, t&p etc comp , earth work in filling on inside & campus of building i/c carrige up to 5.00 km with ramming, dressing proper compactioni/c all cost of material,labour, t&p etc complete , sand fillingin plinth under floors including watering, ramming, consolidating and dressing complete including lead up to 50m and lift upto 1.5m and including cost of sand. , providing and laying in cement concrete1:4:8 (1 cement : 4 coarse sand : 8 graded stone ballast 40 mm nominal size) and curing complete, including cost of form work, in foundation of main building, septic tank & soak pit , providing and injecting chemical emulsion for preconstructional antitermite treatment and creating a chemical barrier under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete (plinth area of the building at ground floor only shall be measured as per i.s.6313 (partii 1981) alderine emulsifiable concentrate or any other approved material such as heptrachlor or chlordane will be used. the rate of application of chemical emulsion shall be as follows : (1) treatment for masonary & foundation 5 liters per sqm. (2) back fill in immediate contact with foundation 7.5 liters/sqm (3) treatment of top surface of plinth filling 5 liters/sqm (4)treatment junction of wall and the floor 7.5 liters /sqm (5) treatment of soil along external perimeter of building 7.5 liters/sqm (6) treatment of soil under apron along external perimter 5 liters/sqm. , r.c.c. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 bwg binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour, t & p etc. required for proper completion of the works. strength of the concrete shall not beless than m 20. but for lintel (using 1:1.5:3 mix concrete f.f) , r.c.c. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in slabg.floor excluding supply of reinforcement and its fixing and binding the same with 24 bwg binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour, t & p etc. required for proper completion of the works. strength of the concrete shall not beless than m 20. , r.c.c. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in slabfirst floor excluding supply of reinforcement and its fixing and binding the same with 24 bwg binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour, t & p etc. required for proper completion of the works. strength of the concrete shall not beless than m 20.(using 1:1.5:3 mix concrete) , r.c.c. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in lighter beam first floor excluding supply of reinforcement and its fixing and binding the same with 24 bwg binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour, t & p etc. required for proper completion of the works. strength of the concrete shall not beless than m 20.i.e. having spans upto 6 m. (using 1:1.5:3 mix concrete ) , r.c.c. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in column first floor excluding supply of reinforcement and its fixing and binding the same with 24 bwg binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour, t & p etc. required for proper completion of the works. strength of the concrete shall not beless than m 20..(using1:1.5:3mix concrete). , first class brick work in 1:6 cement and coarse sand of 2.25 fineness modulus) mortar infoundation & plinth including supply of all materials, labour, t & p etc required for proper completion of the work. , first class brick work in 1:6 cement and coarse sand of 2.25 fineness modulus) mortar but in super structure above plinth level up to floor two level ( up to two storeys ) including necessary cutting and moulding of brick work as required and also including honeycombed brick work in thickness of wall more than 12cms. , first class brick work in 1:4 cement and coarse sand of 2.25 fineness modulus) mortarin superstructure for wall thickness 12 cms , providing & filling of brick bats inside of upper layer in soak pit i/c all cost of material, labour, t&p etc comp , providing and laying brick coba 120 mm thick laid with m 150 class brick bat coba 7.50cm thick with gap of 15mm to each other, over 20 mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with acrelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement & coarse sand mortar finised smooth & top mashed false square 30 cm x 30 cm & side wall parapet shall be mono lythic plaster wall up to 30 cm higherand junction & corner shall be rounded by brick ballast cement & coarse sand masonany coba with top finised plaster mixed with acetic water proofing compound @ 2% by weight & including s/o all material, labour, t& p etc complete for proper completion of work. , p/f h.y.s.d.bars of grade fe 500conforming to is:1786 2006 work such as reinforced concrete to required proper shape as necessary &its wastage including straightening, cutting,bending,binding placing in position for proper completion of the work and including supply of steelbend hooks and authorised over lapping shall be measured upto floor two level. , providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters :(i)32 mm thick single leaf , (ii) 32 mm thick double leaf , mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods,gratings etc. ( when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. (i)fabrication of holdfast for door, chaukhats and windows. , providing & fabrication of m.s. grill ondoor / windows , providing & fabrication ofz section steel windows with openable panels, excluding glass panes. , providing & fabrication ofangle iron chaukhat (40x40x5mm) , supply and fixing galvanized mosquitos proof heavy quality s.s.wire gaugeheavy quality over windows and including supply of teak wood batten 8 cm.x1.cm. (3x3/8)/flat iron 25 mm.x4mm. and including supply of necessary screws all materials, labour, tools & plants etc. required for proper completion of the work. , fixing of door, windows / ventilators chaukhats in position. (a) door chaukhats , (b) window chaukhats , (c) ventilator chaukhats , 15 mm thick cement plaster with cement mortar in proportion of 1:4 cement & coarse sand. , 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or roundedangles not exceeding 80mm in girth and finished even and smooth. (1) 1 cement : 6coarse sand , 12 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80mm in girth & finshed even & smooth. (1) 1 cement : 6 coarse sand , 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or roundedangles not exceeding 80mm in girth and finished even and smooth.in 1:3 (septic tank) , making grooves 10 to 12mmwide 8mm deep in plaster of the walls or in ceiling vertically or horizontally as required. , providing and laying 6 to 8 mm thick ivory or light shade vitrified tiles of 600 x 600 mm size on floor with all colours and shades, laid on 20mm thick cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. , providing and laying 6 to 8 mm thick ivory or light shade vitrified tiles of 600 x 600 mm size on skirting with all colours and shades, laid on 20mm thick cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. , kota stone slab flooring over 25 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick , kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. , supply and fixing 6mm thick china white glazed tiles in flooring or in skirting or dado laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry jointing and polishing complete including supply of all materials, labour and tool sand plants etc. , painting two coat over priming coat (but including cost of priming coat) on steel and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as luxol3 apcolite superlac, dulux specified brushing to give an even shade and including cleaning the surface of all dirt,dust and other foreign matter sand papering and stoping including cost of all materials, labour, t & p etc. required for proper completion of the work. , painting two coat over priming coat (but including cost of priming coat) on wooden surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as luxol3 apcolite superlac, dulux specified brushing to give an even shade and including cleaning the surface of all dirt,dust and other foreign matter sand papering and stoping including cost of all materials, labour, t & p etc. required for proper completion of the work. , finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade: new work (two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). , distempering (two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as berger,j&n, shalimar, asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost of all materials. , providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. , providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : (a) 4 mm thick. , providing & fixing stainless steel sliding door bolts isi markedto required colour or shade with nuts and screws etc complete.(a) 250mm x 16mm , p/fixing stainless steel tower bolts isi marked to required colour or shade with necessary screws etc.(a) 250 mm x 10mm , providing & fixing stainless steel handles isi marked to required colour or shade with necessary screws etc. complete. 125 mm , providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete , providing and fixing stainless steel ( grade 304) railing made of hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer in charge. ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) , providing & laying water proofing treatment in sunken portion of wcs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. this layer will be allowed to air cure for 4 hours. b) second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. this layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. the rate includes preparation of surface, treatment & all corners, junctions of pipes with polymer mixed slurry. , chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).ordinary cement without any pigment , providingandfixingof iron(i)rolling shutter complete , (ii) spring wire 27.5 cm long grade 2 for shutter , (iii) top cover for rolling shutter , (iv)ball bearing for rolling shutter , providing and fixing water closet squatting pan (european type w.c. pan ) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: , providing & fixing white vitreous china wash basin with c.i. brackets painted white, 15mm c.p. brass pillar taps, c.p. brass chain with rubber plug, 32mmc.p. brass waste of standard pattern includingcutting & making good the walls wherever required. ( a)flat back wash basin size 550x400 mm with single 15mm c.p. brass pillar tap. , providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and c.p. brass spreaders with brass unions and g.i clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required one urinal basin with 5 litre white p.v.c. automatic flushing cistern , providing and fixing flexible p.v.c. waste pipe for sink or wash basin including pvc waste fittings complete.a) 32mm dia , (b)40mm dia , providing & fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick asbestos cement sheet ground fixed to wooden cleats with c.p. brass screws and washers. , providing and fixing 45 cm long unplasticised pvc connection pipe with brass unions.(a) 15mm nominal bore , providing & fixing cp brass bib cock of approved quality conforming to is 8931 (a) 15mm nominal bore , providing & fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gmsa) 15mm nominal bore. , providing & fixing c.p. brass angle valve for basin mixer and gyser points of approved quality conforming to is 8931a) 15mm nominal bore , providing and fixing c.p. brass shower rose with 15 or 20 mm inlet 150 mm diameter , providing and fixing c.p. brass stop cock (concealed) of standard design and of approved make conforming to is:8931 15 mm nominal bore , providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes 110 mm diameter , (ii) 75 mm diameter , providing and fixing on wall face unplasticised pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion coupler (i) 75 mm , (ii) coupler 110 mm , (iii) single tee with door 75x75x75 mm , (iv) single tee with door 110x110x110 mm , (v) single tee without door 75x75x75 mm , (vi)single tee without door 110x110x110 mm , (vii) bend 87.5°degree 75 mm dia , (viii) bend 87.5°degree 110 mm dia , providing and fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with ms screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. (i)110 mm dia , (ii) 75 mm dia , providing & fixing soil, wast and vent pipe.75 mm dia sand cost iron s&s pipe. , providing & fixing sand cost iron terminal guard 75 mm dia. , providing & fixing c.i. tee at the inlet & outlet of septic tank. , providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion,(i) single socketed pipes 110 mm diameter , providing and fixing on wall face unplasticised pvc moulded fittings/accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion bend 87.5°degree (i) 110 mm , (ii) shoe (plain)110 mm shoe , providing and fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with ms screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm , making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over p.v.c. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete , providing and fixinggi pipes complete with gi fittings and clamps, including cutting and making good walls etc. (internal work).exposed on wall (i)15mm dianominal bore , 20mm dianominal bore , 25mm dia nominal bore , painting gi pipes and fittings with synthetic enamel paint over a ready mixed priming coat, both of approved quality for new work. (i)15mm dia nominal bore , (ii) 20mm dia nominal bore , (iii) 25mm dia nominal bore , excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m.including getting out the excavated soil & then returning the soil as required,in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m. (a) pipes 80mm to 300mm diameter. , providing, laying and joining glazed stone ware pipes grade awith stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. a) 100mm diameter , (ii) 150mm diameter , providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround s.w. pipes including bed concrete as per standard design. a) 100mm diameters.w. pipe , 150mm diameters.w. pipe , providing and fixing square mouth s.w. gully trap grade a complete with c.i. grating brick masonry chamber with f.p.s. bricks of class designation 75 and water tight c.i. cover with frame of 300 x 300mm.size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design.(a) 150 x 100 mm. size p type , constructing brick masonry manhole with 75 class designation f.p.s. bricks in cement mortar 1:4 (1 cement : 4 coarse sand) rcc top slab with 1:2:4 mix (1 cement : 2 coarse sand: 4graded stone aggregate 20mm nominal size); foundation concrete 1:4:8 mix (1 cement :4coarse sand: 8 graded stone aggregate 40mm nominal size) inside plasstering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design.a) inside size 90x80 cm & 45 cm deep including c.i. cover with frame (light duty) total wt. of cover & frame to be not less than 38 kg (wt. of cover 23 kg & wt. of frame 15 kg. , supply & fixing of medium quality r.c.c. manhole coverwith frame complete.(i)hd. 20 circular shape ,560 int. dia. , (ii) m.d. 10 square shape ,450 int. dia. , supplyfixingand concealing of20mm dia.2mm thick pvc conduit pipe with isi mark embossed and with pvc acessories confirming to is no. 3419 for drawing wires duly sealed at joints with original resin/ adhesive to make the complete piping rigid,plastering with cement sand mortar finished to level with matching colour including cost of material labour and t & p etc required for proper completion of work .( for telephone/t.v.points) , s/f of hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16swgm.s. sheet incorporating 10mm dia, m.s. round barduly bent for supporting fan hanger dully painted withred oxide and screwing arrangement with wiring conduit laid in the r.c.c. roof before concreting along with supply of all materials, labour t & p etc., for proper completion of work , construction of recess distribution board of all sizes including cutting of brick work providing lintel of suitable size & thickness plastering etc. with supply of all materials, labours, t & p etc. required for proper completion of work.600x480x200 mm. size , supply and fixing of factory fabricated m.s. box in existing sunk with godrej type almirah cover with handle etc. fabricated from 18 swg m.s. sheet duly painted with red oxide primer followedby two coats of synthetic enamel paint complete with necessary conduit entry and dp/tpn; fixing arrangement and provision for compartment for loose wires, openable housing on the top and hold fast etc. including supply of all material, labour and t & p etc. required for proper completion of the work.600x480x200 mm. size , supply and fixing of flush/surface mounting distribution boardswithout mcb with additional metal doorcomplete in all respects.6 way tpn cat a...

Directorate of Training and Employment - Uttar Pradesh

29315756 bids are invited for boqauto extension if any seller submits price in last 15 minutes, the rawill be auto extended by 15 minutes ( a maximum of300 times ) average turn over of last 3 years 8 lakh ( s ) total quantity : 1 1 generator wheel 2 copper pipe ½ inch 3 ac wall stand 4 ac pvc 5 colin 6 steel door (7*21/4) 7 steel frame window 4x6 8 steel almirah 9 bag of cloth 10 stepler pin big 11 stepler pin small 12 a4 size paper 13 pin 14 rapper 15 tag 16 dustbin 25 litre 17 challan form 18 pen red 19 pen blue 20 highlighter 21 stamp pad 22 almirah rod (steel) 23 attendence register employee 24 floor tile 2x2 25 wall tile (15x18) 26 cement bag 27 maurang 28 rcc gitti 3/4 29 white cement 50 kg 30 r.o. motor 31 r. o. filter 32 r.o. filter sigment 33 r.o. water supply toti 34 aluminium cable 5 mm 3 core 35 aluminium cable 10 mm 4 core 36 rotary switch 63 amp 37 mcb 63 amp 38 door (7x3*1/4) 39 invertor 850 va 40 battery 150 ah 41 d link 110 box sel 42 d link switch 16 port 43 electric board two way switch circuit 16a 44 multi stant 2.5 mm 45 multi stant 4 mm 46 led bulb 15 watt ...

Directorate of Training and Employment - Uttar Pradesh

29180837 bids are invited for generator wheel , copper pipe ½ inch , ac wall stand , ac pvc , colin , steel door ( 7*21 / 4 ) , steel frame window 4x6 , steel almirah , bag of cloth , stepler pin big , stepler pin small , a4 size paper , pin , rapper , tag , dustbin 25 litre , challan form , pen red , pen blue , highlighter , stamp pad , almirah rod ( steel ) , attendence register employee , floor tile 2x2 , wall tile ( 15x18 ) , cement bag , maurang , rcc gitti 3 / 4 , white cement 50 kg , r.o. motor , r. o. filter , r.o. filter sigment , r.o. water supply toti , aluminium cable 5 mm 3 core , aluminium cable 10 mm 4 core , rotary switch 63 amp , mcb 63 amp , door ( 7x3*1 / 4 ) , invertor 850 va , battery 150 ah , d link 110 box sel , d link switch 16 port , electric board two way switch circuit 16a , multi stant 2.5 mm , multi stant 4 mm , led bulb 15 watt total quantity : 1...

Directorate of Training and Employment - Uttar Pradesh

29173290 bids are invited for boq total quantity : 1 1 pipe 1 / 2 inch 2 brass tee 1 / 2 inch 3 elbow half inch 4 tee 1.5 inch 5 male tee brass 1 / 2 inch 6 brass f tee 7 socket 1 / 2 inch 8 reducer 1½ inch 9 tee 1 / 2 inch 10 teflon tape 11 english sheet 12 plus tank 13 lead connection 2 feet 14 hand corset 15 faucet 16 sulation 17 angle cock 18 toti long body 19 bracket for besin 20 besin fastner 21 besin toti ½ inch 22 elbow ½ inch 45 degree 23 ball cock ½ inch 24 brass valve ½ inch 25 pipe 3 inch 26 elbow 3 inch 27 tee 3 inch 28 socket 3 inch 29 pipe 4 inch 30 elbow 4 inch 31 tee 4 inch 32 short body tonti 33 socket 4 inch 34 c. p. v. c. solution 35 gas 134a 450 gram 36 ac outer pipe 37 copper wire1 mm 38 multi stand 1.5 mm 39 led bulb 30 watt 40 led 20 watt 41 steel door ( 7x4 ) foot...

Village Panchayat - Uttar Pradesh

28860809 provide of construction material brick, cement, morang, balu, stone, blast, gitty, rod, tiles, hume pipe, solar light, street light, electric equipment, handpump equipment, sanitary equipment, pen / pipe, cement concrete tiles, sand, steel door, window, floor tiles, steel with primer, community toilet construction, wall painting....

Uttar Pradesh State Construction and Infrastructure Development Corporation Limited - Uttar Pradesh

28673851 supply of material for balance work of main building, fire station samthar jhansi 2 supply of m.s. angle iron door, windows, ventilator frame made of approved m.s. angle iron wroght to required form including drilling hole, welding and reciting where necessary and also including supply of all materials, such as steel hinges of required size, nut & bolts etc. and also including all taxes, wastage and one coat of red oxide paint complete in all respect as per direction of engineer in charge for proper completion of work at site of work. 3 providing and fixing of m.s. angle iron z section window ( approved section ) with specified design of grill out side openable design of window and gril as per approved drawing 10mmsq bar 75mm c / cand 3no. bar group @ 75mm and four group in horizontal including providing stay and one coat of red oxide primer excluding glass pans. 4 supply and fixing of m.s. grill of approved quality and drawing made of flat iron including supply of all materials, labour and t&p etc also including one coat of red oxide paint comp. in all respect as per direction of engineer in charge ( s.i. no. new item 3 ) 5 s / f s.s. railing stair case 6 s / fixing of aluminium door frame / shutter glazed as per specification. 7 mild steel or iron in plain work such as reinforced concrete or reinforced brick work ( when not included in an over all rates ) wrougth to required shape as necessary including bending for proper completion of the work and including supply of all steel and wastage and over lapping and hooks. r.c.c. work 8 providing and laying of 20mm thick kota stone flooring over 20mm thick base of cement mortar 1:4 ( 1cement: 4 coarse sand ) laid over jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete. 9 supply and filling of sinder in sukan portion of toilet 10 making grooves 10 to 12mm wide x 8mm deep in plaster on the wall or in ceiling etc. 11 making of drip couars in same shade or faces i / x supply of all materials, labour etc. 12 supply and fixing of 35cm ( 1.1 / 4” ) thick commercial quality ( kanju ) sitapur ply or other approved ply wood flush shutters. add extra ( 4560.00+115.00+230.00 ) 13 supply and fixing of stainless steel door fitting. 14 putty two coated including all material t&p etc complete. 15 providing & laying “brick bat coba” 100 mm thick laid with m 150 class brick bat coba 7.50 cm thick with gap of 15mm to each other 20mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with aerelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand mortar finished smooth & top mashed false square 30cmx30cm and side wall parapet shall be monotypic plaster wall upto 30cm higher and junction and corner shall be rounded by brick ballast cement and coarse sand and masonry coba with top finishing plaster mixing with acetic water proofing compound @ 2% by weight & including supply of all materials labour t&p etc. required for proper completion of work and as per direction of e.i.c. 16 making khurra of size 450x450 mm 17 one priming coat and two coat oil bound distemper on new work including supply of all materials, labours and t&p etc. required for proper completion of the work ( s.i.no. 649.+650 ) 18 weather coat two coat coats finishing walls with acrylic smooth exterior paint of required shade 13.46.1 new work ( two or more coat applied @ 1.67 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm ) sqm 90.00 19 painting or varnishing on iron works in small areas or new wood work with one coat of ready mixed priming paint & one coat of approved superior quality ready mixed paint or clear synthetic varnish including supply of all materials labour and t&p etc. required for proper completion of the work. paint to be used should confirm to the isi no.103 1950 ( in two coat. ) wood work. 20 fixing panes of glass with equal or equivalent isi marked quality putty brads and springs and including supply of all materials and labour ete complete. ( 3.80 to 4.7mm thick ) 21 s / fixing of aluminium sheet 24 gauge in door shutter with b & snew toilet 22 supply and fixing 110mmø pvc pipe complete with rose heads bends m.s. clamps 2.5cmx3mm fixed to walls by 15cm long 6mmø nail and including repair of plaster pointing etc if damaged during fixing of the pipes including cost of all material labour, tools and plant etc. required for proper completion of work. 23 mild steel or iron in plain work such as reinforced concrete or reinforced brick work ( when not included in an over all rates ) wrougth to required shape as necessary including bending for proper completion of the work and including supply of all steel and wastage and over lapping and hooks. for r.c.c. work. 24 supply and fixing of 20 gague ward rob shutter in berige 25 supply and fixing of jali door shutter in teak wood 26 supply and fixing of stainless steel masqutio proof jali window. 27 supply and fixing 110mmø pvc pipe complete with rose heads bends m.s. clamps 2.5cmx3mm fixed to walls by 15cm long 6mmø nail and including repair of plaster pointing etc if damaged during fixing of the pipes including cost of all material labour, tools and plant etc. required for proper completion of work. 28 supply of 80mm interlocking concreat block paver 29 supply of stone dust stacking as per directed engineer in charge 30 sanitoryand water supply 31 supply and fixing of european type white glazed earthen ware w.c. pan indian approved 1st quality isi marked backlight seat cover and lit of c.p. brass hinges and rubber buffers. 32 providing and fixing ist quality w.c. orrisa pan white glazed earthen ware isi marked wc pan size 580mm ( hindustan, cera make ) including supply of all materials, labour and t&p etc. required for proper completion of work. 33 supply and fixing of wash hand basin size 550x400mm isi marked basin ( hindustan, cera, parrywere make ) 34 supply and laying of stanless steel sink of size 600x450x200mm with drainges board 35 supply and fixing of c.p. brass towel rail 600mm size together with pair of c.p. brass brackets to fit towel rail. 36 s / f of 600x400mm beveled edge mirror of superior glass mounted on 6mm thick a.c. sheet or plywood sheet and fixed to plastic sleeves with c.p. brass screws and washers. 37 supply and fixing of c.p. soap dise. 38 supply and fixing of pvc tank 1000 lits. 39 supply and fixing of angle cock 40 supply and fixing of 15mmø c.p. short body bib cock. 41 supply and fixing of 100x75mm pvc nahani trap. 42 supply and fixing of c.p.waste 32mmø 43 supply and fixing of c.p.waste 40mmø 44 supply and fixing of c.p. jali 100mmø 45 supply and fixing of c.i. door tee 100mmø 46 supply and fixing of c.i. door bend 100mmø 47 supply and fixing of c.i. door bend 75mmø 48 supply and fixing of m.s. clamp. 100mmø 49 supply and fixing of m.s. clamp. 75mmø 50 making lead joint 100mmø 51 making lead joint75mmø 52 providing and fixing of c.i.pipe isi mark c.i.pipe 100mmø 53 providing and fixing of c.i.pipe isi mark c.i.pipe 75mmø 54 supply and fixing of g.i.pipe 15mmø 55 supply and fixing of g.i.pipe 20mmø 56 supply and fixing of g.i.pipe 25mmø 57 supply and fixing of g.i.pipe 32mmø 58 supply and fixing of g.i.pipe 40mmø 59 supply and fixing of g.i.pipe 80mmø 60 supply and fixing of 15mm pvc connection 45mm long. 61 supply and fixing of gate valve. 25mmø 62 supply and fixing of gate valve. 15mmø 63 supply and fixing of gate valve.32mmø 64 supply and fixing of gate valve. 40mmø 65 supply and fixing of gate valve. 80mmø 66 supply and fixing of urinal 67 supply and laying of pvc sewer line 100mmø ( 317.05+817.00 ) 68 supply and laying of pvc sewer line 150mmø ( 500.20+999.15 ) 69 supply and fixing of c.i. plan bend 100mmø 70 supply and fixing of c.i. plan bend 75mmø 71 supply and laying of pvc 150mm dia line 72 supply of cement pcc 50kg / bag ( mycem / j.k / acc / ultratech ) 73 supply of course sand fm 1.25 2.32 above stacking as per directed engineer in charge 74 supply of 20mm. stone gritt stacking as per directed engineer in charge 75 supply of 40mm. sone ballast stacking as per directed engineer in charge 76 supply of 5mm thick china white glazed wall & floor tile ( size of tiles upto 200x300 mm ) 77 supply of brick m 150 i / c loading, unloading, stacking as per directed engineer in charge 78 supply of oil bound distemper 79 supply of putty 80 acrylic smooth exterior paint 81 supply of granite stone 82 providing & laying of 8 to 10mm thick ivory or light shade vitrified tiles of 600mmx600 mm size...

University Of Lucknow - Uttar Pradesh

28520185 name of work renovation work in the lab of professor vibhuti rai, department of geology (under centre of excellence project) university of lucknow. 1. providing and fixing of 12.5 mm thick gypsum moisture resistant board false ceiling including frame work all complete as per s.i. no. 12.45.3. 2. providing and laying of vitrified floor tiles 600mm x 600mm laid over 20mm thick 1:4 cement mortar as per s.i. no. 11.41.2. 3. providing and fixing of 35mm thick flush doors with all fittings s.i. no. 9.21.21 4. providing and fixing of mild steel door frame for flush doors s.i. no. 10.25.2. 5. providing and applying white cement based putty as per s.i. no. 13.80 6. wall painting with plastic emulsion paint one or more coats s.i. no. 13.98.1. 7. enamel painting in two coats s.i. no. 645, 646. 8. dismantling of brick work as per s.i. no. 692. 9. providing and fixing aluminum partition with glazing 5mm thick all complete s.i. no. 21.3.2. 10. providing and fixing aluminum tubular handle bar all complete s.i. no. 21.12.2 11. providing and fixing of brass 100mm mortice latch and lock as per s.i. no. 21.13...

Village Panchayat - Uttar Pradesh

28387555 supply of brick, brick ballast, cement, gravel, sand, stone ballast, rod, tiles, china tiles, marbles, c.c. interlocking tiles, hume pipe, p.v.c. pipe, solar light, led street light, dustbin, cleaning kit, trolley, electrical items, electric motor, sanitary items, ruler pen, pipes, angle, steel, door, ply, wall and floor tiles, bleaching powder, hypochlorite/insecticide, wall painting, snowcem, hand pump rebore items, sanitary items, fencing wire, iron angle, furniture/bench, dustbin, r.c.c. pillar, spray machine, fogging machine....

Village Panchayat - Uttar Pradesh

28376955 supply of brick, brick ballast, cement, gravel, sand, stone ballast, rod, tiles, china tiles, marbles, c.c. interlocking tiles, hume pipe, p.v.c. pipe, solar light, led street light, dustbin, cleaning kit, trolley, electrical items, electric motor, sanitary items, ruler pen, pipes, angle, steel, door, ply, wall and floor tiles, bleaching powder, hypochlorite/insecticide, wall painting, snowcem, hand pump rebore items, sanitary items, fencing wire, iron angle, furniture/bench, dustbin, r.c.c. pillar, spray machine, fogging machine....

Village Panchayat - Uttar Pradesh

28376712 supply of brick, brick ballast, cement, gravel, sand, stone ballast, rod, tiles, china tiles, marbles, c.c. interlocking tiles, hume pipe, p.v.c. pipe, solar light, led street light, dustbin, cleaning kit, trolley, electrical items, electric motor, sanitary items, ruler pen, pipes, angle, steel, door, ply, wall and floor tiles, bleaching powder, hypochlorite/insecticide, wall painting, snowcem, hand pump rebore items, sanitary items, fencing wire, iron angle, furniture/bench, dustbin, r.c.c. pillar, spray machine, fogging machine....

Village Panchayat - Uttar Pradesh

28318262 supply of brick, brick ballast, cement, gravel, sand, stone ballast, rod, tiles, china tiles, marbles, c.c. interlocking tiles, hume pipe, p.v.c. pipe, solar light, led street light, dustbin, cleaning kit, trolley, electrical items, electric motor, sanitary items, ruler pen, pipes, angle, steel, door, ply, wall and floor tiles, bleaching powder, hypochlorite/insecticide, wall painting, snowcem, hand pump rebore items, sanitary items, fencing wire, iron angle, furniture/bench, dustbin, r.c.c. pillar, spray machine, fogging machine....

Village Panchayat - Uttar Pradesh

28315525 provide of construction material brick, cement, morang, balu, stone blast, gitty, rod, tiles, hume pipe, solar light, street light, electric equipment, handpump equipment, sanitary equipment, pipe, cement concrete tiles, sand, steel, steel door, window, floor tiles, distemper, primer, community toilet construction equipment, wall painting....

Village Panchayat - Uttar Pradesh

28305354 provide of construction material brick, cement, morang, balu, stone blast, gitty, rod, tiles, hume pipe, solar light, street light, electric equipment, handpump equipment, sanitary equipment, pipe, cement concrete tiles, sand, steel, steel door, window, floor tiles, distemper, primer, community toilet construction equipment, wall painting...

Village Panchayat - Uttar Pradesh

28305108 supply of brick, cement, sand, stone ballast, rod, china tiles, hume pipe, solar and street light, hand pump materials, sanitary items, ruler pan/pipe, c.c. tiles, tore steel, steel door/windows, vitrified floor tiles, distemper, snowcem, primer, toilet construction materials, wall painting, brick....

Village Panchayat - Uttar Pradesh

28300862 provide of construction material brick, cement, morang, balu, stone blast, gitty, rod, tiles, hume pipe, solar light, street light, electric equipment, handpump equipment, sanitary equipment, pipe, cement concrete tiles, sand, steel, steel door, window, floor tiles, distemper, primer, community toilet construction equipment, wall painting....

Village Panchayat - Uttar Pradesh

28287692 provide of construction material brick, cement, morang, balu, stone blast, gitty, rod, tiles, hume pipe, solar light, street light, electric equipment, handpump equipment, sanitary equipment, pipe, cement concrete tiles, sand, steel, steel door, window, floor tiles, distemper, primer, community toilet construction equipment, wall painting....

Village Panchayat - Uttar Pradesh

28283892 provide of construction material brick, cement, morang, balu, stone blast, gitty, rod, tiles, hume pipe, solar light, street light, electric equipment, handpump equipment, sanitary equipment, pipe, cement concrete tiles, sand, steel, steel door, window, floor tiles, distemper, primer, community toilet construction equipment, wall painting....

Iti Ltd - Uttar Pradesh

28163678 repairing of wooden/steel doors and windows in factory area ” in iti ltd.,mankapur gonda (up)....

Iti Ltd - Uttar Pradesh

28034188 name of work: “repairing of wooden/steel doors and windows in factory area ” in iti ltd.,mankapur gonda (up)....

Iti Ltd - Uttar Pradesh

27951667 repairing of wooden/steel doors and windows in factory area ” in iti ltd.,mankapur gonda (up). ...

Iti Ltd - Uttar Pradesh

27854936 civil work repairing of wooden steel doors and windows in factory area iti limited mankapur distt gonda...

Uttar Pradesh Rajkiya Nirman Nigam Limited - Uttar Pradesh

26484439 invitation of rates for m . s . fabrication works 1 press steel door/window frame made with 1.25 mm crc sheet including hinges 3 no. isi marked (100x14g) fixed with screw, jams base tie or 20x40mm, ms flat with ms flat iron hold fast 20x40mm, 150mm long including 1 coat of approved zinc chromate anti corrosive paint including fixing of isi marked ms hinges 14 gauge 100mm. 2 85x50 without rebate 3 80x50 without rebate 4 100x50 with one rebate 5 100x50 without rebate 6 120x50 double rebate 7 extra for supply of isi hinges 100mmx14g including fixing in frame 8 do but welding with chaukhat 9 supply of fabricated ms glazed door windows /ventilator of standard steel roller isi z section of required size with ms flat iron hold fast 20x4 mm 150m long including one coast of approved red oxide primer & fitting arrangement complete (cost of fittings will be paid separately) 10 supply of fabricated ms crc sheet (bokaro essar, tata or equivalent) door shutter upto 18 gauge including locking arrangement, handles etc. as per approved design including one coat of red oxide primer. 11 supply of fabricated angle iron nosing made with 35x35x5 mm with red oxide approved primer 12 supply of fabricated ms grill/railing of made of flat/iron / sq. bar of approved pattern and design in required size including fixing with ms frame with one coat of red oxide primer. 13 supply of fabricated m.s. chahali made with flat iron and angle iron of required size and design. 14 supply of fabricated ms angle iron/chaukhat made with 35x35x5, 40x40x6 mm of required size including ms tie rod of 12 mm bar, isi ms hinges (100x14g) 3 no. fixed with screw arrangement isi marked 100 x14 g fixed with frame with hold fast of flat iron 20x4 mm 150 long including one coat of red oxide. 15 fabrication of tower bolt 150mm isi make. 16 fabrication of i hook 200x5mm 17 supply of rolling shutters of approved make made of 80x125 mm (3”x18g) cold rolled ms lath inter locked through their entire length jointed together at the end by locks and mounted on specially designed pipe shafts with brackets side guides , arrangements for inside and outside locking with push and pull operation complete but excluding the cost of top cover and spring. 18 supply of 27.5 cm. long wire spring grade 2 for rolling shutters. 19 supply of top cover for rolling shutters made 18 gauge ms sheet. 20 supply of ball bearing for rolling shutters. 21 supply of 8 mm ms round bar rolling shutter grill of required size with rolling shutter as approved design & pwd specification 22 supply of collapsible steel shutters with vertical channel 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rails of t iron 40x40x6 mm with 38 mm dia steel pulleys with bolts, nuts locking arrangement stoppers handles complete including one coast of primer of approved quality. 23 supply of ci/ms decorated ornamental main campus gate made with m.s. hollow pipe, m.s. sheet, m.s. iron, twisted bar caste iron, c.i. designer pieces as per approved design including cost of red oxide primer of approved quality. 24 supply of ms chahali made with 16 gauge conduit pipe upto 8’ long 1 ½ feet wide frame with 25x4 ms flat both end closed with angle iron and flat rebated as per approved design and drawing of one coat red oxide paints complete. 25 supply of fabricated cow catcher made with 65 to 100 mm g.i. pipe b class isi jindal/surya with ms girder channel as per approved design , drawing for all sizes 26 supply of fabricated rectangle/square hollow pipe /ms pipe /railing /gate/post of different sizes including one coat of red –oxide. 27 –do but ornamental in round, corner 28 supply of mechanical hinges 40 mm round bar with ball and socket joint 40x50 mm. 29 –do but 40x100 mm. 30 supply of m.s measuring box 1’x1’x1’x 25mm ms pipe handles. 31 supply of fabricated tubular trusses shade made with m.s. pipe of required dia as per structure design & drawing including foundation bolt, base plate, wind tie as required, including red oxide paint complete. 32 do but make with angle iron 33 labour charges for erection of above trusses shade including supply of all labour and t&p and required scaffolding, welding, fixing at site complete without civil work. 34 supply of fabricated 3’ x 5’ m.s. chhanna made of 35 x 35 x 5 angle iron frame and stand, g.i. screen of suitable size backing with 1’ x 1’ welded mesh and one coat red oxide primer. 35 supply of power loom 14x24 pure g.i. mosquito wire mesh frame 20x4mm m.s. flat rebated as required size and design including welding, supply & all labour material, t & p etc. required for proper completion of work. 36 supply, fabrication and erection of partition jali frame of 35x35x5 angle iron frame with 1x3x8 gauge welded mesh jali 25x5 flat iron beading cross beading 32x5 including priming coat, all material, labour etc. complete. ...

Village Panchayat - Uttar Pradesh

25522309 supply of cement bag, brick, fine sand, coarse sand, stone grit, ms steel door and window, ms iron steel, ms ramp ruiling, paint, white cement, distemper, supply and fixing of wc, wash hand wasin, pvc water tank, pipe, g.i. pipe, gi elbow, gi socket, pvc pipe, gi pipe outlet....

Village Panchayat - Uttar Pradesh

25416364 supply of cement bag, brick, fine sand, coarse sand, stone grit, ms steel door and window, ms iron steel, ms ramp ruiling, paint, white cement, distemper, supply and fixing of wc, wash hand wasin, pvc water tank, pipe, g.i. pipe, gi elbow, gi socket, pvc pipe, gi pipe outlet....

Village Panchayat - Uttar Pradesh

25381058 supply of cement , fine sand , coarse sand , brick ballast , stone grit , snowcem , bricks , iron steel , white cement , water proofing compound , ms steel door and windows , tiles , white glassed earthen ware pan , urinal seat , supply / fixing of wash hand wasin , pvc water tank , brick cock including fitting , gi pipe glass , gi elbow , gi t , socket , gi pie , pvc pipe , gi pipe outlet , etc...

Iti Ltd - Uttar Pradesh

25285439 subject : labour rate for maintenance of steel/door and window shutter & carry out welding job in iti township, mankapur gonda...