Military Engineer Services - Uttar Pradesh

34895935 repair to all type of map furniture under ge ( west ) lucknow table dining 1200x900x760mm ( 4 pers ) drg no : fd / map / 03 ( for item no 1 to 6 ) : taking out old unserviceable top and s&f top of table shall be madeof 18 / 19 mm prelaminated mdf board ext grade , isi markedis 3087 1985 bonded with phyol pharmeldihide with one sideteak face and other side white of exterior grade quality including with 4 mm thick teak wood beading all round the top complete as specified and directed 2 taking down u / slegs and s&fnew legs1st class seasoned teak wood free from knots and cracks with permissible moisture contentsthroughout as per shape and size complete all as specified and shown on drawing. 3 all as per item no 1 above buttop long rail front or back complete all as specified andshown on drg. 4 all as per item no 1 abovebut top short rail for sides complete all as specified andshown on drg.. 5 provision of konia ( wooden bracket ) of size 4x3 seasoned teak wood 1 thick in between leg and short / long rail of the table fixed with screw to provide more strength complete all as specified and shown on drg. 6 preparation of surface with sand paper after scrubbing and apply two coat of melamine polish glossy finish to table withdrawers with and including to the parts repaired / replaced under item no 1 to 5 to the required gloss to match with the existing complete all as specified andshown on drg. 7 table dinning 1500 x 900 x 760 mm ( 6 pers ) drg no fd / map ii / 03 ( for item no 7 to 12 ) :taking out old unserviceable top and s&f top of table shall be madeof 18 / 19 mm prelaminated mdf board exterior grade, isi markedis 3087 1985 bonded with phyol pharmeldihide with one sideteak face and other side white of exterior grade quality including with 4 mm thick teak wood beading all round the top complete as specified andshown on drg 8 taking down u / s legs and s&f legs of size 90x45mm front / rear left / right made of 1st class seasoned teak wood free from knots and cracks with permissible moisture contentsthroughout as per shape and size complete all as specified on drawing and directed. 9 all as per item no 7 above buttop long rail front or back complete all as specified andshown on drg. 10 all as per item no 7 abovebut top short rail for sides complete all as specified andshown on drg. 11 provision of konia ( wooden bracket ) of size 4x3 seasoned teak wood 1 thick in between leg and short / long rail of the table fixed with screw to provide more strength complete all as specified andshown on drg. 12 preparation of surface with sand paper after scrubbing and apply two coat of melamine polish glossy finish to table withdrawers with and including to the parts repaired / replaced under item no 7 to 11, to the required gloss to match with the existing complete all as specified andshown on drg. 13 repair to chair dining: drg no fd / e6 / map / 10 ( for item no 13 to 20 ) taking out of old broken joints and removing of old ply from seat of chair and s&f new 12 mm bwr phenol formaldehyde resin bonded plywood with permissible moisture contents as per shape and size complete all as specified and shown on in drawing. 14 all as per item no 13 above but front and rear legssize 30x40 1st class teak wood complete all as specified and shown ondrawing. 15 all as per item no 13 abovebut stiffenersize 20x25 mm 1st class teak wood complete all as specified and shown on drawing. 16 all as per item no 13above but all side rail size 65x25 mm 1st class teak wood complete all as specified and shown on in drawing. 17 all as per item no 13above butnylon buffers complete all as specified and shown ondrawing. 18 taking out u / s foam of chair dining and s&f new 75 mm thick 40 density foam with fabric on seat of 12 mm thick plybwr grade duly coveredwith tapestry clothof approved qualityduly stichedcomplete all as specified andshown on drawing. note : cost of tapestry cloth shall not be less than rs 380 / per metre . 19 taking out u / s foam of chair dining and s&f new foam 40 density and 450mmx450mmx75mm and coveredwith tapestry clothof approved qualitycomplete all as specified and shown on drawing.note :cost of tapestry cloth shall not be less than rs 380 / per meter . 20 scraping of old polishing with sand paper / grinder and prepare surface to applying two coats of melamine polish glossy finish to complete chair repaired / replaced under item no 13 to 16 to the required gloss and colour complete all as specified and directed. 21 table computer drg no fd / e6 / map / 03: ( for item no 21 to 29 ) taking down u / s top and s & f newtop made of 18 / 19mm prelaminated mdf boardexterior grade quality, isi marked, including with 4 mm thick oval beading duly polished complete all as specified andshown on drg. 22 taking down u / s drawer with ss chanel and s & f drawer with ss channel 12 / 14, mdf board exterior grade, isi marked made of 18 / 19 mm thickwith 4 mm thick oval beading and drawer 75mm deep on telescope channels duly polished and complete all as specified and as shown on drg. 23 taking down u / s key board tray with ss chanel and s & f new key board tray ( 450 x 480 ) with ss channel 12 / 14 mdf board exterior grade, isi marked made of 18 / 19 mm thick with 4 mm thick oval beading and drawer 75mm deep on telescope channels duly polished complete all as specified andshown on drg. 24 taking out u / s bottom shelf and s & f bottom shelf made of 18 mm thick both side pre laminated mdf board exterior grade, isi marked with 4 mm thick oval beading duly polished and complete all as specified and shown on drg. 25 taking out u / s vertical board and s & f vertical board made of 18 mm thick both side pre laminated mdf board exterior grade, isi marked with 4 mm thick oval beading duly polished and complete all as specified andshown on drg. 26 taking downu / s mouse tray with ss channel and s & f mouse tray with 12 / 14 ss channelmade out of 18 mm thick both side pre laminated particle board, isi marked with 4 mm thick oval beading and 75mm deep on telescopic channels duly polished complete all as specified andshown on drg. 27 taking down u / s handle and s & f handle and shape exists complete all as specified and shown on drg. 28 provision of konia ( gi bracket ) of stainless steel in between of every jointof the table fixed with screw to provide more strength complete all as specified andshown on drg. 29 scraping of old painting with sand paper / grinder and prepare surface to applying two coats of synthetic enamel paint black and polishing glossy finish to complete table computer repaired / replaced under item no 21 to 28 to the required gloss and colour complete all as specified and directed. 30 chair computer drg no fd / map / 01: ( for item no 30 to 37 ) : taking downu / s up down lever and s & f up down adjustable lever with size and shape exists complete all as specified and shown on drg. 31 taking out u / s seat back and s & f seat back of computer chair with size and shape exists complete all as specified and shown on drg. 32 taking out u / s seat and s & f seat of computer chair with size and shape exists complete all as specified and shown on drg. 33 taking out u / s hydraulic jack for and s & f seat of computer chair with size and shape exists complete all as specified and shown on drg. 34 taking out u / s tapestry cloth of seat and s & f tapestry cloth on seat of computer chair approved quality duly sitched complete all as specified and shown on drawing. 35 taking out u / s coaster wheel and s & f coaster wheel of twin of computer chair with size and shape exists complete all as specified and shown on drg. 36 taking out u / s hand rest and s & f hand rest of twin of computer chair with size and shape exists complete all as specified as shown on drg. 37 taking out u / s pedestal assy and s & f of new pedestal assy injection moulded in black 30% glass filled nylon10.5mm dia forged bright zinc plated ms castor pin of press fitted to each prong for holding the castors complete all as specified and directed. 38 chair school with hand board drg no fd / e6 / map / 05: ( for item no 38 to 41 ) :taking out u / s hand board and s & f hand board made of 18 / 19 mm thick mdf board exterior grade, isi marked with size and shape exists complete all as specified and shown on drg. 39 taking out u / s seat and s & f one piece pvc back & seat size and shape exists including 4 nos of stainless steel screw of size 6 to 10x50mm long complete all as specified and shown on drg. 40 taking out u / s rubber shoe and s & f rubber shoe size and shape exists complete all as specified and shown on drg. 41 s & f 4 nos of stainless steel screw ofsize 6 to10x50mm long one side flat for fixing of shelf under the seat complete all as specified and directed 42 chair writingoffrs drg no fd / e6 / map / 12 : ( for item no 42 to 47 ) : taking down u / s seatand s & f new seat of chair writing with size and shape exists complete all as specified and shown on drg. 43 taking down u / s back seat and s & f new back seat of chair writing with size and shape exists complete all as specified and shown on drg. 44 taking out u / s tapestry cloth of seat and back same new s&f tapestry cloth on chair writing approved quality duly stitched complete all as specified on drawing and directed. 45 taking out u / s arms and s & f new armrest made of black internal with shin of chair writing with size and shape exists complete all as specified and shown on drg. 46 taking out u / s stiffener and s & f stiffener made 5mm thick ms flat iron size and shapecomplete all as specified and shown on drg. 47 preparation of surface and applying two coats of synthetic enamel paint black complete all as specified and shown on drg. 48 charpoy ip folding ply top drg no : fd 388 ( r ) ( for item no 48 to 50 ) : taking out u / s ply top and s & f ply top made of 8 mm thick bwr ply, isi marked size and shape exists complete all as specified and shown on drg. 49 welding of broken joints including legs which shall be fixed with frame by nut and bolts of size as exists and applying two coats of og enamel paint over a coat of red oxide primer after cleaning the surface complete all as specified and shown on drg. 50 preparation of surface and applying two coats ofsynthetic enamel paint black complete all as specified and shown on drg. 51 teapoy verandahdrg no : fd / e6 / map / 17: ( for item no 51 to 53 ) taking out u / s top and s & f top made of 18 mm thick pre laminated mdf board of exterior grade top with pvc edge around and size and shape as exists complete all as specified and shown on drg. 52 taking out bottom tray and s & f bottom tray made of 5 mm thick ms bar base tray with size and shape exists complete all as specified and as shown on drg. 53 preparation of surface and applying two coats of synthetic enamel paint black complete all as specified and shown on drg. 54 table bed sidedrg no : fd / e6 / map / 15 ( r ) : ( for item no 54 to 60 ) :taking down old unserviceable top and s&f new top of table bed side shall be madeof 18 / 19 mm prelaminated mdf board of exterior grade isi markedis 3087 1985with one sideteak colour and other side white exterior grade complete all specified and directed. 55 taking out u / s upper drawer and s & f drawer made of 12 mm thick ply, bwrgrade, isi marked complete all as specified andshown on drg. 56 taking out u / s legs and s & f legs of size and shape exists complete all as specified and shown on drg. 57 all as per item no 54 above but lower drawer complete all as specified and shown on drg 58 fixing of new stiffener made of 1st class seasoned teak wood free knots and cracks with permissible moisture contents size 400mmx50mmx25mm complete all as specified and directed 59 taking down u / s handle and s & f handle and shape exists complete all as specified and shown on drg. 60 scraping of old painting with sand paper / grinder and prepare surface for applying two coats of synthetic enamel paint black under item no 54 to 59 to the required gloss and colour complete all as specified and directed. 61 table peg drg no fd / map / 11: ( for item no 61 to 65 ) taking out unserviceable legs and s&f new legs made of 1st class seasoned teak wood free from knots and cracks with permissible moisture contents throughout as per shape and size complete all as specified and shown ondrawing. 62 all as per item no 61 above but long rail / short rail complete all as specifiedand shown on drawing. 63 taking out old unsv stiffenerand supply & fixing of same 1st class teak wood complete all as specified and shown on drawing. 64 taking out old unservicable top and s&f top of table shall be madeof 18 / 19 mm prelaminated mdf boardof exterior grade isi markedis 3087 1985 bonded with phyol pharmeldihide with one sideteak colour and other side white exterior grade complete all as specified and directed. 65 scraping of old polishing with sand paper / grinder and prepare surface for applying two coats of melamine polish glossy finish to complete table peg repaired / replace under item no 61 to 64 to the required gloss and colour complete all as specified and directed. 66 table dressing ladies with mirror drg no fd / map ii / 07: ( for item no 66 to 78 ) taking out old unserviceable mirrorwith frame and supply and fixing looking mirror of size 1200x380mm, 5mm thick duly framed with 1st class hard wood teak ( mp ) and back of mirror covered with 6mm thick bwr ply wood, is 303 grade complete all as specified and shown on drawing 67 taking out old broken glass and s & f 5 mm thick glass pane duly slottedfor sliding purposewith size & shape as exists complete all as specified and shown on drgs. 68 taking down oldlegs and s & f new leg of 1st class hard wood teak ( mp ) free from knots, cracks etc. with permissible moisture with shape and sizeas exists complete all as specified andshown on drawing. 69 all as per item no 66 above but frontside of drawer complete all as specified andshown on drawing. 70 taking down old back & sides of drawers ands & fback & sides of drawer made of 12mm ply woodbwr grade, is 303 with size and shape as existscomplete all as specified andshown on drgs 71 all as per item no 66 above butback of drawer short rail complete all as specified and as shown on drawing. 72 taking down unserviceable bottom ply wood 6mm of drawers and s&f new ply wood 6mm bwr grade isi marked, is 303 gradeas per required size complete all as specified and directed. 73 taking down old top and s & f new top of table of 18 / 19mm thick prelaminated mdf board of exterior grade, isi marked one side teak face and other side balancing white with shape and sizeas exists complete all as specified andshown on drawing . 74 all as per item no, 66 but bottom of table dressing ladiescomplete all as specified and as shown on drawing. 75 all as per item ser no, 66 but sides of table dressing ladies complete all as specified and as shown on drawing. 76 taking down old unserviceable bottom frame and s & f new frame with legs made of 1st class hard woodteak ( mp ) free from knots , cracks etc with permissible moisture contains as per shape and size as exists complete all as specified andshown on drawing . 77 taking down unserviceable shutter and s & f new shutter made of 18 / 19 mm thick pre laminated mdf board exterior grade, isi marked of size and shape as existing complete all as specified andshown on drg. 78 scraping of old polishing with sand paper / grinder and prepare surface forapplying two coats of melamine polish glossy finish to complete table dressing ladies repaired / replace under item no 66 to 77 to the required gloss and colour complete all as specified and directed. 79 tv trolly drg no : fd / e6 / map / 04: : ( for item no 79 to 85 ) taking out u / s top and s & f top made of 18 / 19 mm thick both side pre laminated mdf board exterior grade, isi marked top with edge moulded all around and size and shape as exists and complete all as specified and shown on drg. 80 m&l preparation of surfaces by sand papering and cleaning and polishing with french polish upto the required finish complete all as specified on drawing and directed. 81 taking out u / s side board and s & f side board made of 18 mm thick both side pre laminated mdf board exterior grade top with edge moulded all around and size and shape as exists complete all as specified and shown on drg. 82 taking out u / s back board and s & f back board made of 18 mm thick both side pre laminated mdf board exterior grade, isi marked top with edge moulded all around and size and shape as existscomplete all as specified andshown on drg. 83 taking out u / s glass shutter and s & f glass shutter made of 5.5 mm thick openable with magnetic catcheras existscomplete all as specified andshown on drg. 84 taking out u / s coaster wheel and s & f coaster wheel of twin of tv trolley with size and shape exists complete all as specified and shown on drg. 85 taking out u / s magnetic catcher and s & f magnetic catcher of tv trolley with size and shape exists complete all as specified and shown on drg. 86 hard bed steel drg no fd / map / e6 / 08 ( r ) : ( for item no 86 to 93 ) : taking down old unserviceable ply top and s & f new ply top made of 12 mm thick commercial bwr ply isi : 303 complete all as specified andshown on drg. 87 taking out unserviceable head board and s & f new head board made of 18 / 19 mm thick both side prelaminated mdf board of exterior grade isi marked and including 4mm thick teak wood beading all round with size and shape complete all as specified shown on drg 88 taking out unserviceable foot board and s & f new foot board made 18 / 19 mm thick both side pre laminated mdf board of exterior grade isi marked and including 4mm thick teak wood beading all round with size and shape complete all as specified and shown on drg. 89 taking out unserviceable long rails of bed hard steel and supply and fixing new longrails made of 25 x65 mmms rectangular 18 gauge welded with short rails on bed hard steel size and shape complete all as specified andshown on drg. 90 taking unserviceable short rails of bed hard steel and supply & fixing new short rails made of 25x65 mm ms rectangular 18 gauge welded with long rail on bed hard steel size and shape complete all as specified and shown on drg. 91 taking out unserviceable legs and s & f new legs made of 38 x 38 mm ms square pipe 18 gauge welded with frame of bed hard steel complete all as specified and shown on drg. 92 taking out u / s hard rubber shoe and s & f rubber shoe of size and shape complete all as specified and shown on drg. 93 preparing of surface with sand paper after scrubbing paint to bed hard steel including all parts repaired / replaced under item no 86 to 91 applying two coats of synthetic enamle paint after cleaning te surface complete all as specified and as shown on drg. 94 charpoy with hard top drg no fd / map ii / 01 : ( for item no 94 to 99 ) :taking down old unserviceable ply top and supply and fixing new ply top made of 12 mm thick bwr grade ply isi : 303 complete all as specified andshown on drg 95 taking out unserviceable long rails of bed hard steel and supply and fixing new longrails made of 25 x65 mmms rectangular 18 gauge welded with short rails on bed hard steel size and shape complete all as specified andshown on drg. 96 taking unserviceable short rails of bed hard steel and supply & fixing new short rails made of 25x65 mm ms rectangular 18 gauge welded with long rail on bed hard steel size and shape completeall as specified and shown on drg. 97 taking out unserviceable legs and supply and fixing new legs made of 38 x 38 mm ms square pipe 18 gauge welded with frame of bed hard steel complete all as specified and shown on drg. 98 taking out u / s hard rubber shoe and supply and fixing rubber shoe of size and shape complete all as specified and shown on drg. 99 preparing of surface with sand paper after scrubbing paint to bed hard steel including all parts repaired / replaced under item no 94 to 97 applying two coats of synthetic enamel paint after cleaning te surface complete all as per specified andshown on drg. 100 hat stand with mirror ( drg no fd 233 & fd 3622 ) : ( for item no 100 to 105 ) :taking down old unserviceable frame and supply and fixing frame of size 710x1000mm with 4mm thick teak face ply in front side and shall be covered with 4mm thick commercial ply on back side complete all as specified and as shown on drgs. 101 taking down of u / s mirror and teak wood beading and s&f new mirror of size 300x460x5mm and teak wood beading 10x12mm provided vertically top / bottom vertically ( side ) shall be fixed on right hand complete all as specified andshownon drg. 102 taking down of u / s hanging ms plate and s&f new ms plate of best quality complete all as specified and directed. 103 taking down of u / s brass peg and s&f new brass peg of size 75x120mm best quality complete all as specified and directed. 104 taking down of u / s aluminium peg and s&f new aluminiumpeg of size 75x120mm best quality complete all as specified and directed. 105 preparation of surface with sand paper after scrubbing and french polishing to hat stand , with and including to the parts repaired / replaced under item no 100 to 102 to the required gloss to match with the existing complete all as specified and as shown on drg. 106 bin linen multipurpose :drg no fd / e6 / map / 09: ( for item no 106 to 116 ) :taking down u / s legs and s&f new legsof size 50x50x75mm madeof 1st class hw ( teak ) well seasoned free from knots and cracks with permissible moisture through out shape and size applying duly two coat of french polishedto match existing surface complete all as specified and shown on drg. 107 all as per item no 106 above butbottom frame of size 1060x 290x 25x 45mm complete all as specified and shown on drg. 108 taking down old unserviceable drawers and supply and fixing new drawer made of 12mm thick ply bwr grade, isi marked with size and shape as exists complete all as specified andshown on drg. 109 taking down old unserviceable top and supply and fixing new top made of 18 / 19 mm thick prelaminated mdf board, exterior grade, isi marked. complete all as specified andshown on drg. 110 taking down u / s partition and s&f new partition of mdf board, isi marked of size 610x460mm x18mm complete all as specified andshown on drg. 111 all as per item ser no. 110but top or bottom of size 1220x455mmx18mm complete all as specified and shown on drg. 112 taking down old unserviceable back ply and supply and fixing new ply of size 1220x635mm, 6mm thick commercial bwr grade, is 303 grade complete all as specified andshown on drg 113 allas peritem no 112 above but side of size645 x 455mm complete all as specified and shown on drg. 114 all as per item no 112 abovebutshelf of size 425x770 complete all as specified and shown on drg. 115 taking down old unserviceable handle and supply and fixing newhandle 75mm, brass, chromium plated complete all as specified and as shown on drg. 116 preparation of surface with sand paper after scrubbing and french polishing to side board, with and including to the parts repaired / replaced under item no 106 to114to the required gloss, to match with the existing complete all as specified and as shown on drg....

Uttar Pradesh Rajkiya Nirman Nigam Limited - Uttar Pradesh

33485840 invitation of rates for supply of plywood, block board, door shutter, commercial door and jali door etc invitation of rates for supply of plywood, block board, door shutter, commercial door and jali door etc , supply of boiling water resistant ( bwr ) as per is 303 multi layer, termite & borer proof plywood with glue line protection ( glp ) and glue sheer strength ( gss ) 145 , 6mm , 12mm , 18 / 19mm , supply of 12mm shuttering ply isi bwp , supply ofboiling waterproof ( bwp ) as per is 710 multi layer termite & borer proof plywood with glue line protection ( glp ) and glue sheer strength ( gss ) 145 , 6mm , 12mm , 19mm , supply of boiling water proof ( bwp ) as per is 1659 termite and borer proof block board, with glue line protection. , 19mm , supply of both side laminated flush door shutters with 1mm mica both side as per is 2202 ( part 1 ) bwp ( boiling water proof ) borer and termite proof, glue line protected with organic chemicals. , 30mm , 32mm , 35mm / 37mm , do but one side laminated , 30mm , 32mm , 35mm / 37mm , do but double color laminated flush door shutter , 30mm , 35mm , supply of commercial flush door shutters confirming to is 2202, isi marked with borer & boiling water proof, phenol formaldehyde resin bonded. , do but 25 mm thick , do but 30 mm thick , do but 32 mm thick , do but 35 mm thick , supply of laminated door glass panel / jali panels commercial finish. ( without glass & jalli ) , 30mm thick , 32mm thick , 35mm thick , supply of laminated window glass panel / jali panels commercial finish. ( without glass & jalli ) , 30mm thick , 35mm thick , supply of decorative design doors one side design & one side plain teak finish veneer as isi 2202 door shutter. , 30mm thick , 35mm thick...

Uttar Pradesh Rajkiya Nirman Nigam Limited - Uttar Pradesh

33384549 invitation of rates for supply of plywood, block board, door invitation of rates for supply of plywood, block board, door , supply of boiling water resistant ( bwr ) as per is 303 multi layer, termite & borer proof plywood with glue line protection ( glp ) and glue sheer strength ( gss ) 145 , 6mm , 12mm , 18 / 19mm , supply of 12mm shuttering ply isi bwp , supply ofboiling waterproof ( bwp ) as per is 710 multi layer termite & borer proof plywood with glue line protection ( glp ) and glue sheer strength ( gss ) 145 , 6mm , 12mm , 19mm , supply of boiling water proof ( bwp ) as per is 1659 termite and borer proof block board, with glue line protection. , 19mm , supply of both side laminated flush door shutters with 1mm mica both side as per is 2202 ( part 1 ) bwp ( boiling water proof ) borer and termite proof, glue line protected with organic chemicals. , 30mm , 32mm , 35mm / 37mm , do but one side laminated , 30mm , 32mm , 35mm / 37mm , do but double color laminated flush door shutter , 30mm , 35mm , supply of commercial flush door shutters confirming to is 2202, isi marked with borer & boiling water proof, phenol formaldehyde resin bonded. , do but 25 mm thick , do but 30 mm thick , do but 32 mm thick , do but 35 mm thick , supply of laminated door glass panel / jali panels commercial finish. ( without glass & jalli ) , 30mm thick , 32mm thick , 35mm thick , supply of laminated window glass panel / jali panels commercial finish. ( without glass & jalli ) , 30mm thick , 35mm thick , supply of decorative design doors one side design & one side plain teak finish veneer as isi 2202 door shutter. , 30mm thick , 35mm thick...

Uttar Pradesh Rajkiya Nirman Nigam Limited - Uttar Pradesh

33032828 invitation of rates for supply of plywood, block board, door shutter, commercial door and jali door invitation of rates for supply of plywood, block board, door shutter, commercial door and jali door , supply of boiling water resistant ( bwr ) as per is 303 multi layer, termite & borer proof plywood with glue line protection ( glp ) and glue sheer strength ( gss ) 145 , 6mm , 12mm , 18 / 19mm , supply of 12mm shuttering ply isi bwp , supply ofboiling waterproof ( bwp ) as per is 710 multi layer termite & borer proof plywood with glue line protection ( glp ) and glue sheer strength ( gss ) 145 , 6mm , 12mm , 19mm , supply of boiling water proof ( bwp ) as per is 1659 termite and borer proof block board, with glue line protection. , 19mm , supply of both side laminated flush door shutters with 1mm mica both side as per is 2202 ( part 1 ) bwp ( boiling water proof ) borer and termite proof, glue line protected with organic chemicals. , 30mm , 32mm , 35mm / 37mm , do but one side laminated , 30mm , 32mm , 35mm / 37mm , do but double color laminated flush door shutter , 30mm , 35mm , supply of commercial flush door shutters confirming to is 2202, isi marked with borer & boiling water proof, phenol formaldehyde resin bonded. , do but 25 mm thick , do but 30 mm thick , do but 32 mm thick , do but 35 mm thick , supply of laminated door glass panel / jali panels commercial finish. ( without glass & jalli ) , 30mm thick , 32mm thick , 35mm thick , supply of laminated window glass panel / jali panels commercial finish. ( without glass & jalli ) , 30mm thick , 35mm thick , supply of decorative design doors one side design & one side plain teak finish veneer as isi 2202 door shutter. , 30mm thick , 35mm thick...

Uttar Pradesh Jal Nigam - Uttar Pradesh

29921547 invitation of rates for supply of rmc tmt bar coarse sand bricks cement and stone grit and other materials as per bid document , supply raw material , supply of rate for coarse sand hamirpur fm not less 2.2 , supply of rate forghagra sandfm not less 1.2 , supply of rate forstone grit 12 to 20mm kabrai , supply of rate forstone grit25mm kabrai , supply of rate forstone grit10mm kabrai , supply of tmt bar 8mmdia fe 500 primary steel ( make tata, jindal , sail, rinl) , supply of tmt bar 10mmdia fe 500 primary steel ( make tata, jindal , sail, rinl) , supply of tmt bar 12mmdia fe 500 primary steel ( make tata, jindal , sail, rinl) , supply of tmt bar 16mmdia fe 500 primary steel ( make tata, jindal , sail, rinl) , supply of tmt bar 20mmdia fe 500 primary steel ( make tata, jindal , sail, rinl) , supply of tmt bar 25mmdia fe 500 primary steel ( make tata, jindal , sail, rinl) , supply of cement bags 50kg ppc (make jp, birla, mycem, altratech, prism) , supply of first class bricks m 150 class , construction of cast in situ single under reamed pile of specified 400mm dia and upto 7.00meter depth below pile cap in required grade of cement concrete m25 mix, to carry a safe working load not less than specified, excluding the cost of steel reinforcement, but includingcement, coarse sand, stone grit, all labour and t & p required for boring, concreting, cutting of loose concrete etc. (length of pile for payment shall be measured upto the bottom of pile cap). , extra over single under ream for providing additional bulbs in under reamed piles, under 1000mm diameter. , supply of 25mm thick pvc curing pipe , supply of nariyal gurra , supply of cotton waste , supply of shuttering oil,best quality , supply of pvc pipe for curing 25mm dia (threaded) wall thickness 3mm , supply of polythene sheet , supply of hessian cloth tat patti 1.2 mtr. wide , supply of nariyal broom , supply of old dhoti (3mtr. long) , supply of electrical cables 6mm, aluminumcable two core (make havells, seico, polycab, finolax) , supply of electrical cables ,10mm aluminumcable two core (make havells, seico, polycab, finolax) , supply of electrical cables ,16mm aluminumcable two core (make havells, seico, polycab, finolax) , supply of electrical cables 25mm aluminumcable four core unarmed cable , supply of electrical cables 10mm aluminumcable fourcore unarmed cable , supply of electrical cables 16mm aluminumcable fourcore unarmed cable , supply of 50 watt led halogen light , supply of electrical wire 1mm, copper wiretwo core (make havells, seico, polycab, finolax) insulated , supply of electrical wire ,1.5mm, copper wiretwo core (make havells, seico, polycab, finolax) insulated , supply of electrical wire 2mm, copper wiretwo core (make havells, seico, polycab, finolax) insulated , supply of electrical wire 40/76copper wiretwo core (make havells, seico, polycab, finolax) , supply and laying of sandfilledplastic cementbags (valume 0.035cum) excluding cost of sand and including cost of empty bags, labour, stitching sulely complete for making coffer dam in pond or river , supply of125mm dia 12 fit long wooden bally , s/fabrication of m.s. chahali made with flat iron and angle iron or required size and design. , s/fabrication of ms angle iron /chaukhat made with 35x35x5 , 40x40x6 mm of required size including ms tie rod of 12mm bar, isi ms hinges (100x14g) 3 no. fixed with screw arrangement isi marked 100 x14g fixed with frame with hold fast of flat iron 20x4mm 150 long including one coat of red oxide. , 30 mm thick both side commercial flush door shutters confirming to is 2202 isi marked with borar & boiling water proof phenol formaldehyde resin bonded (brad name assam timber (radium brand) corbett, ajay plywood industries, , supply of bamboos 3 to 4 inch dia and 20 to 25 long , supply of empty drum 200 ltr capacity , supply of studd safty helmate , supplyofsafty belt , supply of safty jacket for water , supply of gum boot , supply of saftyboot , supply ofcc cover blocks 20mm ( m 35 grade) , supply ofcc cover blocks 25mm ( m 35 grade) , supply ofcc cover blocks 30mm ( m 35 grade) , supply ofcc cover blocks 40mm ( m 35 grade) , supply ofcc cover blocks 50mm( m 35 grade) , supply of binding wire 25mm gause of tata make , supply of bentonite powder , supply of np 3 600mm dia hume pipewith one side coller , supply of np 3450mm dia hume pipewith one side coller , supply of np 3 300mm dia hume pipewith one side coller , supply of np 3 250mm dia hume pipewith one side coller , supply of np 3 200mm dia hume pipewith one side coller...

Indian Army - Uttar Pradesh

29766441 bids are invited for 30mm thick wire gauge, gauzed/skelton shutter of size 900x2100mm, factory made solid core, stainless steel 36 gauge fly mesh of 304 grades. 30mm thick wire gauge, gauzed/skelton shutter of size 900x2100mm, factory made solid core, stainless steel 36 gauge fly mesh of 304 grades.brand: 1.m/s luxmi doors, faizabad road, lucknow2.m/s choithi industries, 106/369, jeenat market, 1st floor, kalpi road, kanpur. 3.m/s oriental door mig 76, kda colony, jagmak, kanpur. 4.m/s goyaal industrial corp, 14/5, mathura road, faridabad, haryana. , flush door shutter factory made solid core teak 35 mm thick flush door shutter factory made solid core teak veneered facing on both sides isi marked of exterior grade/bonded with phenol formaldehyde resin bwp quality and door shutter shall be internally lipped/framed of size 900x2100mm.brand: 1.m/s luxmi doors, faizabad road, lucknow2.m/s choithi industries, 106/369, jeenat market, 1st floor, kalpi road, kanpur. 3.m/s oriental door mig 76, kda colony, jagmak, kanpur. 4.m/s goyaal industrial corp, 14/5, mathura road, faridabad, haryana. total quantity : 1...

Indian Army - Uttar Pradesh

29532320 bids are invited for 30mm thick wire gauge, gauzed/skelton shutter of size 900x2100mm, factory made solid core, stainless steel 36 gauge fly mesh of 304 grades. 30mm thick wire gauge, gauzed/skelton shutter of size 900x2100mm, factory made solid core, stainless steel 36 gauge fly mesh of 304 grades.brand: 1.m/s luxmi doors, faizabad road, lucknow2.m/s choithi industries, 106/369, jeenat market, 1st floor, kalpi road, kanpur. 3.m/s oriental door mig 76, kda colony, jagmak, kanpur. , wooden flush door shutter (solid core) 35 mm thick flush door shutter factory made solid core teak veneered facing on both sides isi marked of exterior grade/bonded with phenol formaldehyde resin bwp quality and door shutter shall be internally lipped/framed of size 900x2100mm.brand : as above total quantity : 1...

Kanpur Electricity Supply Co Limited - Uttar Pradesh

27896595 annual maintenance and repair works of bijlighar kesco kanpur 2 excavation in foundation in ordinary soil (loam clay or sand) including lift upto 1.5m and lead upto 30m and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of the foundation work. (csi no. 4.01) 3 clearing jungle including uprooting of rank vegetations,grass, bush, wood, trees and saplings of girth upto 30cm measured at a height of 1.0m above ground level and removal of rubbish upto a distance of 50m outside the periphery of uppcl area cleared. (csi no. 4.08) 4 local fine sand of 1.25 f.m. filling in plinth including supply of necessary quantity of sand from a river/canal nearest to the site of work including watering, ramming and dressing etc. rate to include cost of all materials, labour and t&p etc. required for proper completion of work. (kda apprd.) 5 concrete with 4 cm gauge brick ballast, coarse sand (f.m. 1.8 to 2.5) and cement in proportion of 12:6:1 in foundation and under floors including supply of all materials, labour and t & p etc. required for proper completion of the work. (pwd 5.01/273) 6 cement concrete with 2cm gauge approved hard stone ballast, coarse sand (f.m. 1.8 to 2.5) and cement in proportion of 4:2:1 including supply of all materials, labour,side shuttering if required and t&p etc. required for proper completion of work. (csi no. 5.06) 7 first class brick (class 150) work in 1:6 cement and coarse sand (f.m.1.8 to 2.5) mortar in foundation and plinth including supply of all materials, labour & t&p etc. required for proper completion of work. (csi no. 6.01) 8 first class brick (class 150) work in 1:6 cement and coarse sand (f.m.1.8 to 2.5) mortar in super structure of one brick thick wall including supply of all materials, labour & t&p etc. required for proper completion of work. (csi no. 6.01+6.08) 9 first class brick (class 150) work in 1:4 cement and coarse sand (f.m.1.8 to 2.5) mortar in super structure of 1/2 brick thick wall including supply of all materials, labour & t&p etc. required for proper completion of work (csi no. 6.03+6.09) 10 12 mm thick plaster with cement mortar consisting of one part of cement & four part of coarse sand(1:4),minimum thickness not to be less then 10 mm including supply of all material, labour and t&p etc for proper completion of work. (csi no. 11.09) 11 add for extra labour to all items of plaster if done in ceiling. (csi no. 11.10) 12 dismantling reinforced cement concrete or reinforced brick work, including stacking of dismantled materials as directed by the engineer incharge within a distance of 60 metres. (csi no. 15.03) 13 dismantling brick work or stone work in lime or cement mortar and including stacking of materials as directed by the engineer in charge within a distance of 60 metres. (csi no. 15.01) 14 dismantling cement concrete or brick or granolithic floors including base concrete and including stacking of dismantled materials as directed by the engineer in charge within a distance of 60 metres. (csi no. 15.05) 15 dismantling existing plaster including disposal of refuse as directed by the engineer i/c within a distance of 60 m. (csi no. 15.11) 16 supply of 80 mm thick i shaped mechanically compressed inter locking cement concrete paver block manufactured by high pressure & controlled vibration machine having plan dimension 200x(160+120 mm) with minimum 5 mm thick toping of o.p.cement mixed with 25% marble powder. the compressive strength of concrete pavers blocks shall not be less than 30 mpa & 4.5 kg/no. including cost of all material, labour, t&p etc. required for proper completion of work as directed by engineer in charge but execluding u.p.t.t. which shall be paid extra as per rules. (csi no.12.23) 17 mild steel or iron work of small sizes and sections such as holding down bolts, holdfasts tie rods, gratings etc. (when not included in an overall rates) wrought to required shape form including supply of steel bolts, nuts, wastage etc. and their fixing, required for proper completion of the work including cost of steel (which shall be arranged by the contractor). (csi no. 9.00) 18 tmt/tor steel in plain work such as reinforced concrete or reinforced brick work (when not included in an over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage, bend, hooks and authorized overlapping shall be measured. (steel shall be arranged by the contractor)(csi no. 9.03) 19 repairs to plaster of thickness (with cement mortar 1:4 (1cement: 4 coarse sand) 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per directions of engineer in charge (cpwd 14.1.2) 20 3 mm thick floating coat of neat cement finish including supply of all materials,labour and t&p etc. required for proper completion of the work. (cement consumtion 0.044 bag/sq.m.) (csi no. 11.20) 21 applying birla or equivalent putty on new interior or exterior surface over one coat of water based cement primer of ici or equivalent brand for smoothening and levelling of the surface as per requirement and direction of engineer i/c including cost of all material, labour, t & p etc required for proper completion of work. (csi no. 13.20) 22 applying birla putty or equivalent putty on previousaly bila putty smoothen surface over one cost of water base cement primer of ici or equivalent brand for smoothining and leveling of the surface as per requirement and direction of e/i including cost of all material , labour and t&p required for proper completion of work.(csi no.13.21) 23 one priming coat and one coat oil bound distemper on new work including supply of all materials,labour and t&p etc. required for proper completion of the work. (csi no. 13.08) 24 same as in item (13.08) but for every coat after the first coat. (csi no. 13.09) 25 as above in item no. (13.08) but for every coat on previously old oil bound distemper surface. (csi no. 13.10) 26 painting one coat with apex or equivalent brand weather coat paint on new wall surfaces (well prepared with birla putty and one coat of primer ici or equivalent which shall be paid separately) including thorough washing with water including cost of all materials, labour, t&p required for proper completion of work. (csi no. 13.22) 27 same as in item no 13.22 above but for every coat of additional apex or equivalent brand weather coat paint . (csi no. 13.23) 28 same as in item 13.22 but for each coat of apex or equivalent brand weather coat paint .on previously treated surface. (csi no. 13.24) 29 painting one coat with acrylic emulsion paint of berger/ asian/ ici or equivalent paint (paint and water in the ratio 1:1 by volume) over prepared and primed surface of cement concrete, cement plaster and bricks including all labour, material and t&p etc required for proper completion of the work, (preparation of base with birla putty etc. and a coating of primer shall be paid extra) . (csi no. 13.25) 30 same as above in item no. 13.25 but for every coat after first coat of acrylic emulsion paint of berger/ asian/ ici or equivalent paint. (csi no. 13.26) 31 same as above in item no. 13.25 but one coat of acrylic emulsion paint of berger/ asian/ ici or equivalent paint on previously painted surface. (csi no. 13.27) 32 4.0 cm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and t&p etc, required for proper completion of the work. without base cc (csi no. 12.04) 33 supply and laying 8 mm thick glazed floor tiles of somany, johnson or equivalent make, of size 300x300 mm, laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry, jointing and polishing complete, including supply of all materials, labour and t&p etc. completion required for proper completion of the work. (csi no. 12.11) 34 supply and laying 6 mm thick glazed tiles of size 200*300 or 450*300 mm in skirting / dado laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry, jointing and polishing complete,including supply of all materials, labour and t&p etc. completion required for proper completion of the work. (csi no. 12.12) 35 providing and laying floor of 10 mm thick vitrified tiles(premium quality) in flooring or skirting of approved brand (bell, johnson or equi. make) size of 600x600 mm of approved shade, colour and pattern , laid over base cement mortar 1:4 mix including finishing the joints with white cement mixed with pigment to match the shade of tile including cost of all material, labour and t&p required for pr (csi 12.18a) 36 providing and laying of 20 mm thick granite ( black/ brown) in flooring or skirting ,of approved shade, colour,size and pattern , laid over base cement mortar 1:4 mix including finishing the joints with white cement mixed with pigment to match the shade of granite floor including cost of all material, labour and t&p required for proper completion of the work, as per direction of engineer incharge. (csi no.12.20a) 37 extra for making edge moulding to 20mm thick granite stone counters, vanities etc in proper shape and size as per direction of e/i . including machine policing to give high gloss finish complete.(csi no.12.20b) 38 providing and fixing of 110 mm dia p.v.c. pressure pipe (6 kg/sq.cm.) for water supply mains with specials such as tee, bend, socket, elbow etc. including cutting of pipe wherever necessary and including excavation of trenches (450x600) mm for laying the pipe line and including its back filling after testing the pipe line including watering, ramming etc. complete including disposal of surplus earth from the site up to 100m as per direction of e/i including supply of all material, labour, t&p etc. required for proper completion of work. (csi no. 24.47 sor 2017) 39 s/f galvanized mosquitos proof heavy quality iron wire gauge (14x24) over window frames and including supply of shishum wood battens 8cm x 1cm. and including supply and fixing of necessary screws, all materials,labour and t&p etc. required for proper complete. (csi no. 8.44) 40 renewing panes of 4.8 t0 5.7 mm glass including supply of glass with putty and brads including supply of all materials, labour and t&p etc. required for proper completion of the work.(a) glass of 5 mm thick. (csi no. 20.04a) 41 indian shishum wood wrought framed and fixed including simple, mouldings straight work as in chaukhats including supply of all materials, labour and t&p etc.required for proper completion of the work . (csi no. 8.02) 42 supply and fixing of 3.5 cm. thick shisham wood fully panelled door and window shutter including supply and fixing of wooden cleats and stoppers and including fixing and adjustment of hinges bolts, locks, handles, springs and/or other fittings but excluding their supply and including fixing the glass panes with putty and necessary screws (glass panes to be 4 mm thick.). (csi no. 8.23) 43 providing and fixing 19.00 mm thick ply board/block board for wardrobe shutter etc. of reliance or scorpio or equivalent make including teak wood beading around the shutter and including fixing and adjustment of hinges, bolts handle and other fittings but excluidng their supply and including cost of all material labour, t&p etc. required for the proper completion of the work. (old csi 8.25) 44 p/f of 6.0mm thick water proof commercial quality plywood in partition work to make 5x4mm size groove at specified intervals. ply shall be fixed by means of glue and headless nailsat 100mm c/c complete. cost including all labour, material,t&p required for proper completion of work. (old csi 8.30) 45 providing and fixing 15 mm dia b class jindal,jtc, isi marked g.i. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed gi fitting where required, cutting and making good the walls etc and all materials, labour and t&p complete. (csi no. 26.01a) 46 same as in item no. (26.01 above but for 20 mm dia. (csi no. 26.01(b)) 47 same as in item no. (26.01 above but for 25 mm dia. (csi no. 26.01(c)) 48 same as in item no. (26.01 above but for 32 mm dia. (csi no. 26.01(d)) 49 supply & fixing of cpvc pipe 20mm (chlorinated polyvinyl chloride) having thermal stability for hot and cold water supply including all cpvc plan, bras thread fitting and required labour etc. complete in all respect. (dsr/pwd 18.8.2) 50 supply & fixing of cpvc pipe 15mm (chlorinated polyvinyl chloride) having thermal stability for hot and cold water supply including all cpvc plan, bras thread fitting and required labour etc. complete in all respect. (dsr/pwd 19/18.8.1) 51 providing and fixing full way 15mm dia g.m. gate valve with wheel, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. (csi no. 26.04a) 52 providing and fixing full way 20mm dia g.m. gate valve with wheel, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. (csi no. 26.04b) 53 providing and fixing full way 25mm dia g.m. gate valve with wheel, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. (csi no. 26.04c) 54 supply and fixing of syntex or equivalent make water storage tank including all materials, labours, t&p etc required for proper completioon of work. (csi no. 26.12) 55 providing and fixing pvc ball float valve 15 mm dia. with brass & union complete, isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. (csi no. 26.06) 56 supply and fixing pvc nahani trap of heavy quality over minimum 75 mm thick cement concrete in proportion of 1:2:4 including cost of cement concrete, all materials, labour, t&p etc. required for proper completion of work. (old csi 25.27) 57 providing and fixing 100mm. dia c.p. grating over nahani trap or drain holes including cost of all materials, labour and t & p etc. required for proper completion of the work. (old csi 25.24) 58 p/f 32 mm dia p.v.c. waste pipe. (csi no. 27.14) 59 providing and fixing 10 littres low level pvc flushing cistern, complete with all fittings including supply of all materials, labour and t&p etc. required for proper completion of the work. (csi no. 27.12) 60 roviding and fixing plastic seat cover complete with plastic lid for european type wc isi marked including supply of all materials,labour and t&p etc.complete. (csi no. 27.04) 61 providing and fixing 100 mm dia pvc p or s trap including cement concrete and all materials, labour cartage t&p etc.required for proper completion of the work.(for w.c.) (csi no. 27.24) 62 providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with c.p. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete (cpwd 17.33) 63 providing and fixing pvc connection pipe, 300x15 with 2 brass units isi mark heavy quality including supply of all materials, labour and t&p required for proper completion of work. (csi no. 26.09) 64 providing and fixing in position 32 mm. dia p.v.c. flush pipe. for w.c. with unions, bends etc. including supply of all materials,labour and t&p etc.required for proper completion of the work. (csi no. 27.13) 65 providing and fixing of 15 mm dia c.p.brass angle valve of heavy quality l&k or equiv. make including supply of all materials, labour and t&p etc. required for proper completion of the work. (csi no. 26.16 i) 66 providng and fixing 15 mm dia c.p. brass stop cock of l & k or equivalent make including supply of all materials, labour and t&p etc. required for proper completion of the work. (csi no 26.16d) 67 providing and fixing first quality white glazed orissa pattern w.c.pan hindustan, cera make. size 580 mm.(hindustan,cera make) with out p trap including supply of all materials,labour and t&p etc.complete. (csi no. 27.01) 68 providing and fixing of ist quality white glazed earthen ware wash hand basin isi marked size 510mm x 400mm (hindware or equivalent make) with r.s. or c.i. brackets, c.p. brass pillar cock 15mm dia (weight not less than 400 gms) isi marked, 32mm dia c.p. brass chain with rubber plug, 32mm dia c.p. brass waste standard pattern with check nut, p.v.c. connection 15 mm dia including cutting and making good the walls and floor including cost of all required materials, labour and t& p etc. required for proper completion of work ( fittings to be used should be of superior quality as per approved sample). (old csi 25.08) 69 providing and fixing first quality white glazed european pattern w.c.pan hindustan, cera make. size 580 mm.(hindustan,cera make) with out p trap including supply of all materials,labour and t&p etc.complete. (csi no. 27.02) 70 providing and fixing 600 mm x 450 mm beveled edge mirror of atul,kiran makeglass with indian polish 6.50 mm thick complete with back of 600 mm x 450 mm x 6 mm hard board sheet fixed to wooden cieats with c.p. brass screws and washers including supply of all materials, labour and t&p etc.required for proper completion of the work. (csi no. 27.15) 71 thorough cleaning of pvc tank with bleaching powder and rubbing inside surface of oht with jute and wire brush including cleaning and washing the surface with water including operation of tubewell and valves if required as per direction of e/i including cost of all materials, labour and t&p etc. required for completion of wrok. (oldcsi 22.38a) 72 taking out unwanted weeds/trees from the wall/roof of residence and disposal the same outside the corporation area. (old csi 22.23) 73 supply and fixing of chromium polished iron fitting with screws for doors and windows etc. a to l (old csi 8.17 a to l) 74 l drop 16 mm dia 12 long 75 l drop 16 mm dia 10 long 76 l drop 12mm dia 8 long 77 tower bolt 10 long 78 tower bolt 8 long 79 tower bolt 6 long 80 handle 6 long 81 handle 4 long 82 m.s hinges 5 long 83 m.s hinges 4 long 84 m.s hinges 3 long 85 stopper with rubber pad 86 plastic/rubber cleat 87 s/f of 25 mm dia decorative curtain rod with decorative end caps, matching curtain rings, including fixing with necessary clamps, pvc gully, steel screws etc. complete. (old csi 8.19) 88 supply & fixing fresh air fan of 200mm of crompton or equivalent make including labour & tp etc. (nsi) 89 supply and fixing brass polished hydraulic door closure of approved make & quality its fixing and adjustment with the help of screws, nuts and bolts including supply of all labour, t & p etc. required for proper completion of the work. (csi no. 8.60) 90 cleaning and sweeping of roof of residence as and when required including uprooting of rank vegetation and disposal of the garbage upto 50 m.(csi no. 22.20) 91 attending to petty maintenance service like plumbing service, welder service, mason service and carpenter service required as below. 92 (b) job attending by one no. plumber/welder/mason/carpenter with two no. helper per hour or part of an hour. 93 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer in charge (cpwd 17.16a) 94 cleaning of septic tank including disposal of waste out side the uppcl area as per direction of the engineer in charge including cost of all labour,t&p etc.required for proper completion of the work.(csi no. 20.12) 95 cleaning of existing pipe line of different dia. ranging from 4 to 2 dia. including digging trenches and refilling, opening of pipes, cleaning of pipes, cutting, threading, if required fixing and including making good the road, wall etc as directed by the engineer i/c.(csi no. 20.26a) 96 cleaning of existing water pipe line of different dia up to 2 dia including digging trenches and refilling,opening and cleaning of pipes,cutting,threading,if required fixing and including making good the road and wall etc. as directed by the engineer in charge.(csi no. 20.26b) 97 cleaning of r.c.c. over head tank up to capacity of one lac. liters and chlorinating with bleaching power mixed to water as per direction of engineer in charge complete.(csi no. 20.27) 98 supply and mixing bleaching powder in over head tank as required or as directed by engineer in charge.(csi no. 20.29) 99 providing and fixing 12 mm thick shuttering ply by replacing of panels including detatching the shutters, opening out and seperating the frame members and panels and including reassembling the shutter in part and again refixing the shutter including cost of all material, labour and t&p etc. required for proper completion of work. (old csi 22.09) 100 providing and fixing sun film of gareware or equivalent make on glass panes of door and window shutters including cost of all materials,labour and t&p etc. required for proper completion of the work.(csi no. 22.14) 101 providing hard rubber beading at bottom of door covered with aluminium strips for restoration of air conditioning and prolection from rats etc. as per direction of engineer in charge including cost of materials,labour, t&p etc. required for proper completion of the work. (old csi 22.108) 102 opening of aluminium door shutter and refixing the same after replacement of new rubber beading and screws complete excluding cost of al. pipe and glass but including cost of rubber beading and screw. cost including all labour, material and t&p required for proper completion of work. (old csi 22.116) 103 providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by engineer in charge) 0.50 mm ( + 0.05 %), total coated thickness with zinc coating 120 gm per sqm as per is:277 in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by engineer in charge. the sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with epdm seal, complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (dsr 12.5) 104 dismantling corrugated iron roofs walls or partition including purlins battens and vertical support and including stacking of materials as directed by the engineerin charge with a distance of 60 metres. (200 feet). (pwd 17.11) 105 providing and fixing mineral fibre board modular false ceiling in usg or armstrong or equivalent make as approved by architect in regular edge mineral textured tiles with approved surface pattern of size 600mmx600mm having noise reduction co efficient 0.5 .06 , light reflaction over 75% relative humidity 95% , suspension system of true lock exposed grid system with 15mm wide flanges of white color , fixed to the structural soffit by butterfly clip hangers, suspenstion wires & anchor fastener as per the manufacturers specification. suspension wires to be provided at every 600mm c/c with two nos of ties on each anchor fastener , perimeter trim of truelock wall angle in white color secured to wall at 450mm maximum centre. the work to be completed as per direction e/i. (old csi 8.35) 106 removing and refixing galvanized iron corrugated or a.c. sheet roofing in position including cutting of old rusted bolts, if required, and including supply of bolts, nuts and hooks & j/u washer etc. required for proper completion of work. (old csi 22.14) 107 cleaning white glazed tiles with spirit and caustic soda including supply of all materials, labour and t&p etc. required for proper completion of the work. (old agr. rate based on c.s.i. no. 20.09/ sch rate 27.71) 108 providing and fixing double scaffolding system (cup lock type) on the exterior side, upto seven story hight made with 40 mm dia. m.s. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with m.s. tubes, m.s. tube challies, m.s. clamps and m.s. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. the scaffolding system shall be stiffened with bracings, runners, connection with the building etc. wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of engineer in charge. the elevational area of the scaffolding shall be measured for payment purpose. the payment will be made once irrespective of duration of scaffolding. (sch. rate 27.91/ 2014/nsi) 109 providing and fixing false ceiling with 12mm thick plain/semi perforated or with design ceiling tiles of bwp type phenol formaldehyde synthetic resin bonded pressed particle board conforming is:3087 finished with a coat of aluminium primer on both sides & edges and tow coats of synthetic enamel paint of approved quality on exposed face fixed to a grid made out of anodized aluminium (with 15 micron anodic coating) t sections 35x15x1.5mm size main runners and cross runners 23.5x19x1.5mm fixed to main runners placed 600mm square. the frame work shall be suspended from ceiling by level adjusting hangers of 6mm diameter m.s. rod fixed to roof slab by means of ceiling cleats. the suspenders shall be placed 600x1200mm center to center including fixing to the frame with c.p. brace screws and applying a priming coat of zinc chromate yellow primer (aluminium frame work shall be paid separately) (revsed rate 27.92/2014/old c.s.i. no. 16.03) n. 110 p/f fully anodized aluminium fixed glazing with hindalco or equivalent extruded standard sections14gauge (2.41mm thick) of various cross sections and joints mitred and jointed as shown in drawing including providing & fixing 5.5 mm thick toughened glass with neoprene beading & aluminium glazing clips all around. the minimum thickness of anodizing on all aluminium sections should be 20 microns with a (+) 2 microns tolerance . the rate should include the cost of fixing the aluminum frame on teak wood frame or finished wall (rb/rcc/masonry) surface by means of 80 mm long approved counter sunk screws provided at 500 mm c/c or part there of starting from 100 mm above the bottom in vertical member and 100 mm from both the ends of horizontal top and bottom member excluding cost of teak frame but including cost of all other material, labour, tools & plants etc. complete. (csi no. 8.52) n. 111 same as above item no. 8.52 but for openable window portion as shown in drawings, including cost of aluminium hinges and all other fittings like concealed tower bolts handles etc of approved quality and including cost of all other material, labour, tools & plants etc. complete. (csi no. 8.53) 112 shown in drawings including cost of hinges and aluminium fittings like tower bolts, handles, stoppers, push plates, brass body with brass component 6 levers cocealed lock etc of heavy & approved quality and including cost of all other material, labour, tools & plants etc. complete. (csi no. 8.54) 113 s/fixing of double action floor springs including cutting in floors / rcc slabs and grouting the same with c.c. & finishing the surface properly as and where required under aluminium doors as per direction of engineer in charge. including cost of all other material, labour, tools & plants etc. complete. (csi no. 8.55) 114 supplying & fixing 24 gauge annodized aluminium sheet of approved quality including cutting, wastage and fixing the same over the wooden door shutters with nails with all material, labour and t&p. (csi no. 8.63) 115 supply and fixing 24 b.w.g , g.c. iron sheet roofing .fixed in position with j or u bolts 10 mm. dia with g.i. limpet & bitumen washers including supply of all materials, labour,wastage. and t&p etc. required for proper completion of the work. (csi no. 10.01) 116 as in item 10.01 but 6 mm thick grey corrugated asbestos sheet. (csi no. 10.03) 117 spreading over leaky roofs with bitumen paints at 0.45 kg per sq.m. including sweeping, cleaning the roof with brushes, heating of the paints upto the required temperature,pouring it on the surface, spreading of necessary quantity of approved coarse sand 1 cft. per 100 sft. and including supply of all materials, labour and t&p etc. required for proper completion of the work. (csi no. 10.05) 118 supply and laying one layer of tar felt or any other equivalent approved material at the junction of wall & roof or at any place as per direction of the engineer incharge including necessary overlap, applying a coat of approved mastic paint below the tar felt & including supply of all materials, labour and t&p etc. required for proper completion of the work. (csi no. 10.06) 119 s/mixing approved water proofing compound (cico,dr fixit etc) in cement mortar in plaster or concrete work in the proportion as recommended by the manufacturer. (csi no. 11.15) 120 painting or varnishing new iron work in small areas or new wood work with one coat of ready mixed priming paint and one coat of approved superior quality ready mix paint luxol or equivalent brand or varnish including supply of all materials, labour and t&p etc. required for proper completion of the work. paint to be used should conform to the i.s. 103 1950. (csi no. 13.01) 121 as in item 13.01 above but for every coat after first coat. (csi no. 13.02) 122 as in item 13.01 above but for every coat on previously painted old wood or iron work including its sand papering,rubbing and cleaning as required, for proper completion of work. (csi no. 13.03) 123 supply and fixing 35mm thick factory made panel single leaf, hot pressed, phenol formaldehyde resin bonded, boiling water resistant, commercial quality sitapur ply wood or other isi marked factory made flush door shutters conforming to is: 2202 part 1 ( 1983) including fixing of wooden cleats and stoppers and including fixing and adjustment of hinges, bolts, locks, handles, springs and/or other fittings approved by engineer in charge but excluding their ( fittings) supply but including painting two coats of black japan on iron fittings if necessary.(csi no. 8.24 sor 2017) (csi no. 29.05d) 124 making expansion joints with 24 gauge aluminium sheet &8 inch wide tarfelt fixed with tarmastic in roof or floors fitting joints with approved bitumen as per direction of engg. in charge incl. supply of all material , labour & t&p etc. for proper completion of work.(csi no. 10.14 sor 2017) (csi no. 29.29) 125 flooring with p.v.c. tiles 1.5 mm. thick including cost of all materials,labour and t&p etc. required for proper completion of the work. (old c.s.i no. 12.31) 126 disposal of rubbish / debris out side the uppcl area as per direction of er/in charge including cartage, labour and materials, t&p etc. required for proper completion of the work. (no. deduction for voids shall be made). (csi no. 20.16) ...

Uttar Pradesh Rajkiya Nirman Nigam Limited - Uttar Pradesh

23313757 invitation of rates for supply of plywood , block board , door shutter , commercial door and jali door , supply of boiling water resistant ( bwr ) as per is 303 multi layer , termite & borer proof plywood with glue line protection ( glp ) and glue sheer strength ( gss ) 145 , 6mm , 12mm , 18 / 19mm , supply of 12mm shuttering ply isi bwp , supply of boiling water proof ( bwp ) as per is 710 multi layer termite & borer proof plywood with glue line protection ( glp ) and glue sheer strength ( gss ) 145 , 6mm , 12mm , 19mm , supply of boiling water proof ( bwp ) as per is 1659 termite and borer proof block board , with glue line protection . , 19mm , supply of both side laminated flush door shutters with 1mm mica both side as per is 2202 ( part 1 ) bwp ( boiling water proof ) borer and termite proof , glue line protected with organic chemicals . , 30mm , 32mm , 35mm / 37mm , do but one side laminated , 30mm , 32mm , 35mm / 37mm , do but double color laminated flush door shutter , 30mm , 35mm , supply of commercial flush door shutters confirming to is 2202 , isi marked with borer & boiling water proof , phenol formaldehyde resin bonded . , do but 25 mm thick , do but 30 mm thick , do but 32 mm thick , do but 35 mm thick , supply of laminated door glass panel / jali panels commercial finish . ( without glass & jalli ) , 30mm thick , 32mm thick , 35mm thick , supply of laminated window glass panel / jali panels commercial finish . ( without glass & jalli ) , 30mm thick , 35mm thick , supply of decorative design doors one side design & one side plain teak finish veneer as isi 2202 door shutter . , 30mm thick , 35mm thick...

Uttar Pradesh State Construction and Infrastructure Development Corporation Limited - Uttar Pradesh

18373746 supply of balance material at ats maniha govindaspur , main building and dormitory, dining type 3, 2, 1 , jaunpur. 1.01 both side commercial flush door shutters confirming to is 2202 ( part 1 ) 1999, isi marked with borar & boiling water proof, phenol formaldehyde resin bonded 30 mm thick flush door shutters ( single leat 1.19x2.08 ( 24 nos ) 1 02 30 mm thick flush door shutters ( single leaf ) o.99x2.08 ( 45 nos ) 1.03 30 mm thick flush door shutters ( double leaf ) 0.89x2.08 ( 4 nos ) 1.04 30 mm thick flush door shutters ( double leaf ) 0.99x2.08 ( 45 nos ) 1.05 30 mm thick flush door shutters ( single leaf ) 0.89x2.08 ( 24 nos ) 1.06 30 mm thick flush door shutters ( single leaf ) 0.74x2.08 ( 149 nos ) 1.o7 30 mm thick flush door shutters ( double leaf ) 1.78x2.08 ( 4 nos ) ...