S N Medical College And Hospital - Uttar Pradesh

35007688 tender for annual maintenance of medical gas pipeline system annual mantinance ofmedical gas pipe line system ( mgps ) , at ed, mch block, peadiatrics, tbcd, opthalmology, medicine, surgery & allied specilty, s.n.medical college and hospital, agra 2 pipe cu 76mm 3 pipe cu 54mm 4 pipe cu 42mm 5 pipe cu 28mm 6 pipe cu 22mm 7 pipe cu 15mm 8 pipe cu 12mm 9 pipe cu 10mm 10 isolation valve 76mm 11 isolation valve 54mm 12 isolation valve 42mm 13 isolation valve 28mm 14 isolation valve 22mm 15 isolation valve 15mm 16 isolation valve 10mm 17 regular mon 30 18 pressure adjusting screen mon 30 regulator 19 spring for mon 30 regulator 20 bonnet for mon 30 regulator 21 ring brass 22 plate diaphragm 23 o ring 24 diphragm mon30 25 seat nylon 26 intermediate regulator 27 diaphragm modified 28 tail pipe 02 / n20 29 shuttle valve 30 non return valve for manifold 31 seat neoprene 32 valve self sealing oxygen / n2o / ca / vac 33 brackest type 34 cover plasticoxygen / n2o / ca / vac 35 button chrome oxygen / n2o / ca / vac 36 hp tubing antistatic oxygen / n2o / ca / vac 37 metal component oxygen / n2o 38 adapter pipe line ( probe ) 39 adapter twin 40 flow meter bpc 41 ward vacuum unit 42 bottle theatre suction unit 43 theatre suction unit 44 gauge minimumn contract 45 blocker for manifold 46 gauge 0 250 47 seal bodak 48 piston lp 5&5.5 49 connecting rod gm 50 crank bush 51 cylinder 5x5.5 52 piston ring set 53 set of piston ring 54 finger valve for v 255 / v 244 55 valve assay, new 56 set of gas kit 57 bearing 6310 58 bearing 6380 59 connecting rod bush 60 filter pad 61 poston pin 62 crank nut 63 crank plate 64 allan bolt for crank 65 oil seal 66 crank shaft 67 piston lock 68 cylinder head 69 exhaust silencer 70 ms union 21 / 2 71 pipe ms 1 1 / 2 72 pipe ms 2 73 belt 74 lubricating oil per ltr 75 filter assay, for vacuum 76 rewinding of 10hp motor 77 rewinding of 5hp motor 78 bail bearing of 5 hp motor 79 bail bearing of 10hp motor 80 contractor 5hp motor mk 1 81 over load relay 5hp motor 82 indicator lamp 83 cylinder lp with flange 84 cylinder hp with flange 85 piston lp 86 piston hp 87 pin poston lp / hp 88 sealing ring lp 89 bearing ring lp 90 sealing ring hp 91 bearing ring hp 92 air filter 93 gasket 94 crank shaft 95 bearing housing ( flywheel end ) 96 bearing housing 97 bearing ( c.r ) 98 connecting rod 99 valve strip lp / hp 100 valve guide lp / hp 101 grease nipple 102 electrical gland 103 electrical cable per mt. 104 piston ring 1 set 105 7.5 hp motor winding 106 motor bearing 107 motor starter 108 motor contractor 109 overload relay ( 4 16 amp ) 110 single phase preventer 111 v belt 1 set 112 motor pulley 113 pressure switch 114 non return valve 3 / 4 115 nipple for nrv 116 grease gum 117 activated alumina 118 timer 119 solenoid valve 120 pre filter 121 after filter 122 coil ( sol.valve ) 123 pressure gauge 124 valve 125 bolt ( 12 nos ) 126 semi automatic control panel oxygen & n20 127 fully automatic control 128 diaphragm 2nd stage 129 seal tube 130 moulded tyre 131 wheel assay complete for anaesthesia machine 132 tyre for b / p 133 assay change over block 134 emergency know for b / f 135 lever 136 gauge oxygen 0 250 ) kg / cm2 for b / basic 137 gauge nitrous ( 0 200 ) kg / cm2 138 bar clamping 139 assay pin & screw 140 nrv for oxygen 141 nrv for n20 142 front panel 143 diaphragm pipeline 144 saddle 28mm 145 saddle 22mm 146 saddle 15mm 147 saddle 10mm 148 tube flow meter oxygen 149 humidifire flow mtr oxygen 150 plastic bracket for b / basic 151 top tray for b / basic 152 nrv cum now up valve 153 regulator oxygen 154 regulator nitrous oxide 155 yoke oxygen 156 yoke nitrous oxide 157 plug filter 158 beg mount 159 head brink expiratory valve 160 tube corrugated 161 adapter plug in house 162 angle mount 163 bag rebreathing 2lt 164 bag rebreathing 1lt 165 assy. control valve oxygen 166 shoulder screw 167 piece distance 168 mettalic tubing oxygen 169 mettalic tubing nitrous oxide 170 mettalic tubing for a / c 171 post gauge 172 bag rebreathing 0.5lt 173 humidefiere for head hood 174 angle 175 cylender key oxygen / n2o 176 oxygen nut 177 n20 nut 178 spanner 179 slyriner 180 alarm pipe 181 alarm albow 4mm / 6mm 182 fasia 183 changeover 184 alarm 185 saddle 56mm 186 saddle 42mm 187 genitic valve 188 flow meter oxygen cylinder 189 oxygen mask 190 tail pipe nut oxygen / n20 191 ward vacuum unit bottle 192 ward vacuum unit meter 193 handle 194 tie 195 screw 196 point oxygen / n2o / air / vacuum 197 clip 198 two way 199 adopter anesthesia trolley 200 point spring 201 alarm sheet 202 gress for pump & motor per kg 203 flow meter tube per mtr 204 flow meter battle ring 205 bpc flow meter complete 206 semi automatic control panel 207 fullyautomatic control panel 208 manifold with midle frame nrv & tailpipe 1+1 209 manifold with midle frame nrv & tailpipe 2+2 210 manifold with midle frame nrv & tailpipe 3+3 211 manifold with midle frame nrv & tailpipe 4+4 212 manifold with midle frame nrv & tailpipe 5+5 213 manifold with midle frame nrv & tailpipe 6+6 214 manifold with midle frame nrv & tailpipe 7+7 215 manifold with midle frame nrv & tailpipe 8+8 216 line alarm digital 1 line 217 line alarm digital 2 line 218 line alarm digital 3 line 219 line alarm digital 4 line 220 line alarm digital 5line 221 line alarm digital 6 line 222 valve box1 line 223 valve box 2 line 224 valve box 3 line 225 valve box 4 line 226 valve box 5line 227 valve box 6 line 228 nrv for manifold 229 outlet point oxygen 230 outlet point vacuum 231 outlet point air 4 232 outlet point air 7 233 outlet point n2o 234 outlet point agss 235 outlet point co2...

Northern Railway - Uttar Pradesh

34905341 supply of automatic star delta starter suitable for 15 hp 3 phase 415v 50n, with combined bimetal overload relay and single phasing preventor and with 415 volts ac 50 cycles coil, fabricated in sheet steel enclosure similar to bch type nasakle 415.the starter generally confirming to is 1822 1967automatic star delta starter suitable for 15 hp 3 phase 415v 50n, with combined bimetal overload relay and single phasing preventor and with 415 volts ac 50 cycles coil, fabricated in sheet steel enclosure similar to bch type nasakle 415.the starter generally confirming to is 1822 1967, automatic star delta starter suitable for 15 hp 3 phase 415v 50n, with combined bimetal overload relay and single phasing preventor and with 415 volts ac 50 cycles coil, fabricated in sheet steel enclosure similar to bch type nasakle 415.the starter generally confirming to is 1822 1967....

National Thermal Power Corporation Limited - Uttar Pradesh

34858067 procurement of cands make switchgear spares for ntpc rihand , 3 pole, 415 volt power contactor ac 3 , power contactor,18a,415v,ac3 , power contactor 3p 415v ac 110v ac 63 a , power contactor 3p 415v ac,110v ac,80 a , power contactor 3p 415v ac 110v ac 185 a , power contactor 3p 415v ac 110v ac 265 a , power contactor 3p 415v ac 230v ac 65a , power contr 3p 415v ac cv 415v ac 265 a , powercontactor 16a240vac lc1d173 a60 , pwr contactor 415v 16a 110vac coil tc , pwr contactor 415v 32a 110vac coil tc , thermal oload relay0.63 1a , thermal o/l relay,0.63 1.0a,c&s make , thermal overload relay:a1 1.6a:gen , thermal o/l relay,1.6 2.5a,c&s make , thermal o/l relay,2.5 4.0a,c&s make , direct mounting o/l relay 5.5 8.5a , thermal o/l relay,7.0 10.0 amp,c&s make , thermal oload relay9 13a , overload relay lr1 d16321 13 18amp , thermal o/l relay,23 32amp,c&s make , overload relay 28 40amp tc make , direct mounting o/l relay 30 40 a , thermal o/l relay,30 40 amp,c&s make , thermal o/l relay,38 50 amp,c&s make , thermal overload relay lrid63(48 57a) , overload relay auto/manual 45 65amp , o/lrelay65a 105a/480vaclri f105,tcmake , thermal o load relay63 80 a , swtch dis fuse:13947pt3:h duty tpn , switch fuse unit is:13947 250a 415 , mushroom head pb actuator , contact element 1no+1nc rear connection , handle for switch type cssf 200 400a , handle for switch type cssf 32a 125a , 240v ac coil for lc1 d503 a 60 ac3 tc , 110v ac coil for lc1 265 tc make , 110v ac coil for lc1 f185/lc1 f225 tc , main contact set for lc1 f265 tc make , addon block for c&s contactor 2no+2nc , thermaloverload relay lr1 d63361,57 66a , relay tca2 dn40,coil,240v,4no...

National Thermal Power Corporation Limited - Uttar Pradesh

34821750 procurement of spares of landt make lt switchgear for ntpc unchahar , power contactor type 3tf46 02 0afo,45a , pwr contr:3p 415ac:coil:110ac:225a:l&t , pwr contr:mnx265,coil volt 110v ac , mn400,400a,2no+2nc,110vac,ss94043,l&t , selector switch on / off16a,240v ac ,l&t , s/w sel:2:pos:25a,110vac:l & t , racking handle for l&t make cn cs , s/w sel:3:pos:16a,240vac:l&t , tpswitch,sk91000,l&t make 63a,type:ff , s/w sel:ammtr s/w:6a,240vac:l & t , l&t:arc chute 1600a,sl90855 , trpng coil 1600a cb l&t 110vdc sl92718 , power contctr.: 3p, 110vac, l&t mnx18 , pwr.contctr.: 3p,110vac,110vac,l&t mnx32 , powr contr:3p415vac:110vac:l&t:mnx32 , powr contr:3p415vac:110vac:l&t:mnx45 , powr contr:3p415vac:110vac:l&t:mnx70 , powr contr:3p415vac:110vac:l&t:mnx80 , powr contr:3p415vac:110vac:l&t:mnx140 , powr contr:3p415vac:110vac:l&t:mnx185 , powr contr:3p415vac:110vac:l&t:mnx225 , powr contr:3p415vac:110vac:l&t:mnx325 , powr contr 3p 415v ac cv 110v ac 80a , closing coil 220v,dc,ah 25c cs , power contactor 3p 415v ac 110v ac 25 a , thermal overload relay range : 4.5a, mn2 , thermal o load relay6 10a l & t , o/l relay l&t mn2; 9 15a singleeph.prot. , thermalo/lrelay mn2,9ato 15a,ss94131 l&t , o/l relay,mn 2 type,l&t make, 14 23a , o/l mn5 14 23a,l&t make , o/l relay,range:30 50 l&t make mn5 type , o/l relay,range:45 75 type:mn5 l&t make , thrm overlod rely amp 45 75al&t , thermal overload relay lrid63(48 57a) , thermal o/l relay60 100amp mn 12 type , 90 150amp over load relay l&t make , 135 225amp over load relay l&t make , l&t sw tpn type: fac 63a cat sk 95156 , s/w isol:hd 3 pole+neutral:100a:415v:l&t , s/w isol:hd 3 pole+neutral:125a:415v:l&t , thermalo/lrlymn2,2ato3.3a,ss94131,l&t , 3 pole power contactor,95a,type:mnx 95 , power contactor mnx225coil11o va l&t , s/w sel:volt mr selector s/w:6a 415v:l&t , isolting s/w:normal duty d p:16a:230v , s/w isol:hd 3 pole+neutral:630a:415v:l&t , s/w isol:hd 3 pole+neutral:320a:415v:l&t , s/w isol:hd 3 pole+neutral:200a:415v:l&t , l&t:s/w disconctr fuse:fnx63#sk95804 , add on block 2no+2nc for mn16,make:l&t. , operating handle:c&s make:sfu:250amp , thermal overload relay mn2 0.9 1.5amp , thermalo/lrlymn2,1.4ato2.3a,l&t , thermal bi metal relay,mn2,2 3.3a,l&t...

North Eastern Railways - Uttar Pradesh

34515686 supply of hv overload relayhv overload relay, hv overload relay ( qlm ) with mechanical interlocking arrangement having 2 nc interlock type di as per clw specification no. clw / es / r 27, alt. z or latest specn: clw specification no. clw / es / r 27, alt. z or latest...

National Thermal Power Corporation Limited - Uttar Pradesh

34410741 supply of c and s make spares for electrical maintenance works at ntpc supply of c and s make spares for electrical maintenance works at ntpcsingrauli , power contactor 3p 415v ac, 110v ac, 32 a , power contr 3p 415v ac cl 220v ac 16 a , pwr cntor:3p 415ac:coil:110ac:16a , acb single pole unit 800a, cond unit 8d , closng coil model avh c 116, 250vdc acb , position indicator switch for c&s acb , module incoming ( male ) moving contact 125 , comp module 10.1 12.0kw typ:dk2 mcc , powercontactor 16a240vac lc1d173 a60 , thermal o / l relay ct opd 100 160amp , relay cat no.ca2 dn140, 110v ac, 10a, , o / l rly2.5a to 4a, lr1d09308, tc make , thermal overload relay:a1 1.6a , thermal o load relay0.63 1a , o / l relay, type lr1 d09304 0.4 to 0.63 a , 110v ac aux. contactor la1, d22 , contactor, type:lc1d173f with 110v ac , powr contr:3p415vac:110vac:c&s:lc1fdp400 , powr contr:3p415vac:110vac:c&s:lc1fdp265 , pwrcontr;240vac265a;2no+2nc;telemec;lc1f , fixed contact set ( 1 set = 3 poles ) , spring charging motor, 220v a.c. , charging hook for c&s acbs. , auxiliary isolating contact block c&s , main fixed contacts for 2500a acb , lt acb shunt coil 220v dc, avh s 220md , main moving contct assy, movmain 06d 08d , acb main isolating contact ( jaw ) , mic 25d , l / mechnsm typ 6 16b / d p lowermech16b , position indi switch c&s acb up to 1600a , sfu 63a, tpn c&s make cssf63 , sfu 400a, tpn c&s make cssf400 , sfu: heavy duty tp 32a 415 v , switch fuse unit 250 amp , switch disconnector unit:tp:63a:415v , panel mounted switch 415v ac, 630a , motor protector circuit breaker , air circuit breaker rs is:10027 3200a , main contacts for lc1f265 la5 fh431 , main cont lc1f 185 contactor 185a c&s , spare kit;pwr contr;16a;tc;lc1d173;la5d , add on block with 2no+2nc type la1 d22 , :mcc / db:c&s:comp module pk21 110kw , main contact set for lc1 f265 tc make , pwr contctr:c&s:contactr ( d ) 63 a 1no 110v , main contact set for lc1 d803 tc make , arcing contact ( fix / moving ) , thermal overload relay lr1 d09310 ( 4 6a ) , thermal overload relay lr1 d16321 13 18a , thermal overload relay lr1d25322 ( 18 25a ) , thermal overload relay lr1 d32353 23 32a , thermal overload relay lr1 d63357 38 50a , thermaloverload relay lr1 d63361, 57 66a , aux cont set 7no+7nc for c&s acb , closing spring for c&s bkr2500amp...

Uttar Pradesh Power Transmission Corporation Limited - Uttar Pradesh

34137707 auto mode operation of marshalling box of 100 mva transformer ii at 220 kv s / s bhupiamau and 40 mva transformer i at 132 kv s / s lalganj, under electy. trans. division pratapgarh 1 work of designing the circuit with contractor / overload relay / fuse / mcb / selector switch for auto and manual mode operation of cooling fan & oil pump with wti & oti, testing and rectifying the faulty of wti / oti / buchholz / prv / mog / osr alarm and trip, including replacement of faulty cable of marshalling box following power transformer at 220 kv s / s pratapgarh and 132 kv s / s lalganj with all associated work. 2 suply and fixing of 3no+1nc three phase contractor for cooling fan / oil circulating pump ( pick up potential 250v / ac / 9a ) of standard make. 3 100 mva ( cgl make ) t / f ii at 220 kv s / s pratapgarh. 4 40mva ( imp make ) t / f i at 132 kv s / s lalganj. 5 suply and fixing of 3no+1nc three phase contractor for auto / manual mode selection ( pick up potentiol 250v / ac / 32a ) of standard make. 6 100 mva ( cgl make ) t / f ii at 220 kv s / s pratapgarh. 7 40mva ( imp make ) t / f i at 132 kv s / s lalganj. 8 suply and fixing of three phase mcb ( 4 pole / 415v ac / 32a ) . 9 100 mva ( cgl make ) t / f ii at 220 kv s / s pratapgarh. 10 40mva ( imp make ) t / f i at 132 kv s / s lalganj. 11 suply and fixing of over load relay for fan and motor ( 6 12a ) 12 100 mva ( cgl make ) t / f ii at 220 kv s / s pratapgarh. 13 suply and fixing of selector switch for auto / manual selection ( 2way / 2w / off, 415v ac 10a ) 14 100 mva ( cgl make ) t / f ii at 220 kv s / s pratapgarh. 15 40mva ( imp make ) t / f i at 132 kv s / s lalganj. 16 suply and fixing of terminal block ( 415v ac / 32a ) 17 100 mva ( cgl make ) t / f ii at 220 kv s / s pratapgarh. 18 40mva ( imp make ) t / f i at 132 kv s / s lalganj....

Uttar Pradesh Rajya Vidyut Utpadan Nigam Limited - Uttar Pradesh

33763785 supply of spares of eot crane for the o / h 0f #9, btps, obra spares of eot crane for the o / h 0f #9, btps, obra , master controller 5 steps 11 can spring return to off position, type: mc 16, 440 v, 10a , master controller 5 steps 14 can spring return to off position, type: mc 16, 440 v, 10a , timer 0.5 60 sec, coil voltage 110 vac , pvc tape ( is:7809 part ii ( sect 1 ) 1986 isi mark of size 1.9cmx10 mtr. make: steel grip / any std. make , rotary limit switch, type 2nc, 60:1 , rotary limit switch, type 2nc, 48:1 , limit switch, warm driver type wdls / p4 / 100 , limit switch, counterweight type 1nc , thermal overload relay, current setting range 90a to 150a, ( ct operated ) separate mounting , thermal overload relay, current setting range 53a to 99a, ( ct operated ) separate mounting...

North Eastern Railways - Uttar Pradesh

33645269 supply of power contactor 70 amps, triple pole with auxiliary contacts 2 no / 2nc, operating coil voltage 415 v ac, 50 hzpower contactor 70 amps, triple pole with auxiliary contacts 2 no / 2nc, operating coil voltage 415 v ac, 50 hz, power contactor 70 amps, triple pole with auxiliary contacts 2 no / 2nc, operating coil voltage 415 v ac, 50 hz to catalogue no. 3tf 47 72 0a with suitable overload relay siemens make or exactly equivalent ( including physical dimensions ) of abb make ( catalogue no. b75 30 00+ca7 22e ) or l&t make ( catalogue no. mnx70st19002 ) , confirming to is / iec60947, part 4 / sec 1. as per rcf specification no. edts 041 ( rev. b ) . accepted make: siemens, abb, l&t, schneider only general stores depot uttar pradesh 119.00 numbers...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32982839 18 / ecc ( d ) ag / 2022 23 18 / ecc ( d ) ag / 2022 23 , supply & installation, testing & commissioning of single girder e.o.t crane overhead ( out door / indoor type ) of 5.0 mt capacity suitable of 10 m approximate crane span and 6 m approximate lift and tested to 25% over load and comprising of electric motor / brake / gears, connectors overload relay features, wire rope hoist with all accessories pendant type controller, trailing cable etc of approved make and other safety features as specified in techincal specification as per direction of engineer in charge. , supply & erection of l.t. gantry girder of ismb 350 size with ismc 300 channel capping welded to top flange with 40 mm square bar welded on the top of the channel at 6m height approximate as per direction of engineer in charge. , supply & installation of shrouded insulated 4 pole bus bar capacity 100 amp. with g.i. conductor with all accessories as per direction of engineer in charge....

Indian Army - Uttar Pradesh

32693611 bids are invited for repair / maintenance of ac plant at awacs store 4 wing under ge ( af ) tech area 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 supply and fixing in replacement filter of existing capacity and size complete all as specefied. supply and fixing in expansion valve for 3 x 15 tr ac plant complete all as specefied and directed. s&f in replacement of v belt of existing size for air handling unit, complete all as specefied and directed. supply and fixing in replacement overload relay complete all as specefied and directed. s&finreplacementsinglephasepreventorforprotectionsystemfromsinglephasingcompleteallasspecefied and directed. supplyandfixinreplacementpressuregauge100mmdial0 21kg / cm2ratingcompleteallasspecefiedand directed. descalingoftheentirewatercirculationgsystemforcentralacplantwatercooledthreeunit3x15tracplantwatercooledalongwithcondensors, coolingtower / pipingpumpsetc.openingcondensorbydisconnectingnutboltsandcleaningwithdescalingsolutionwithhelpofdescalingpump / wirebrush, cleaning rod etc circulating above solution in condensor pipe lines as requried time, flushing out the gasleakagetestingandrepairof3x15trentirerefregerationsystemandflushingofoilfromcoolingcoilbynitrogengas, cleaning&washingfins, removingthealldustparticlesincludingsoldering / weldingetcfor sealing and testing complete all as specefied and directed supply&fixingofcompressorofcap7.5tr ( modelnosz185s4rcmake:danfoss ) afterdisconnection of old compressor from base frame and tesing complete all as specefied and directed supply and filling refrigerent gas r 407 c complete all as specefied. dismantlingandtakingdownelectricmotorofcapacity7.5hpandstripopeningandrewindingwithsuperenamelledcopperwindingwireofsamegaugewithproperclassofinsulationandapplyingvarnish, dryingetcincludingreplacementofbearingsreassemblingthemotor, reinstallationinsamepositingcompleteincluding testing complete all as specefied and directed. all as per item no 7 above but electric motor of capacity 3.0 hp s&f in replacement contactor 3 phase 32 amp 415 volt, complete all as specefied and directed. s&finreplacementwatertemperaturesensoer ( in&outwater ) of3x15tracplantcompleteallasspecefied and directed. s&finreplacementofbutterflyvalve ( 125mm ) , includingrubbergasket, nutboltwashercompleteallasspecefied and directed. s&f in replacement air release valve complete all as specefied and directed. s&f in replacement of lp / hp switch of 3 x 15 tr ac plant complete all as specefied and directed. s&finreplacementwatertemperaturegaugesuitablefor15tracplantcompleteallasspecefiedanddirected....

Indian Army - Uttar Pradesh

32693609 bids are invited for repair / maintenance of ac plant at tyre bay of 4 wing under ge ( af ) tech area supply and fixing in replacement overload relay complete all as specefied and directed., ...

Medical College - Uttar Pradesh

32677779 gas pipe line repair work at svbp hospital, meerut 2 oxygen pipeline with manifold, control panel & outlet [rates for amc(including minimum 3 services and when required)] 3 nitrous oxide pipeline with manifold control panel & outlet. [rates for amc(including minimum 3 services and when required)] 4 vacuum pipeline with vacuum pump including all its attachment and electrical accessories & outlet. [rates for amc(including minimum 3 services and when required)] 5 air pipeline with vacuum pump including all its attachment and electrical accessories & outlet. 6 description of spare part(s) 7 pipe cu 76mm 8 pipe cu 54mm 9 pipe cu 42mm 10 pipe cu 28mm 11 pipe cu 22mm 12 pipe cu 15mm 13 pipe cu 12mm 14 pipe cu 10mm 15 isolation valve 76mm 16 isolation valve 54mm 17 isolation valve 42mm 18 isolation valve 28mm 19 isolation valve 22mm 20 isolation valve 15mm 21 isolation valve 10mm 22 regular mon 30 23 pressure adjusting screw mon 30 regulator 24 spring for mon 30 regulator 25 bonnet for mon 30 regulator 26 ring brass 27 plate diaphragm 28 “o” ring 29 diaphragm mon30 30 seat nylon 31 intermediate regulator 32 diaphragm modified 33 tail pipe 02/n20 34 shuttle valve 35 non return valve for manifold 36 seat neoprene 37 valve self sealing 02/n20/ca/vac 38 bracket s type 39 cover plastic 02/n2o/ca/vac 40 button chrome 02/n2o/ca/vac 41 hp tubing antistatic 02/n2o/ca/vac 42 metal component 02/n2o 43 adapter pipe line. 44 adapter twin 45 flow meter bpc 46 ward vacuum unit 47 bottle theatre suction unit 48 theatre suction unit 49 gauge minimum contact 50 blocker for manifold 51 gauge 0 250 52 seal bodak 53 piston lp5&5.5 54 connecting rod gm 55 crank bush 56 cylinder 5x5.5 57 piston ring set 58 setof piston ring 59 finger valve for v 255/v 244 60 valve assay, new 61 set of gas kit 62 bearing 6310 63 bearing 6380 64 connecting rod bush 65 filter pad 66 poston pin 67 crank nut 68 crank plate 69 allan bolt for crank 70 oil seal 71 crank shaft 72 piston lock 73 cylinder head 74 exhaust silencer 75 ms union 2”/ 1/2” 76 pipe ms 1 ½” 77 pipe ms 2” 78 belt 79 lubricating oil 80 filter assay, for vacuum 81 rewinding of 10hp motor 82 rewinding of 5hp motor 83 ball bearing of 5hp motor 84 ball bearing for 10hp motor 85 contractor 5hp motor mk 1 86 over load relay 5hp motor 87 indicator lamp 88 cylinder lp with flange 89 cylinder hp with flange 90 piston lp 91 poston hp 92 pin poston lp/hp 93 sealing ring lp 94 bearing ring lp 95 sealing ring hp 96 bearing ring hp 97 air filter 98 gasket 99 crank shaft 100 bearing housing (flywheel end) 101 bearing housing 102 bearing (c.r) 103 connecting rod 104 valve strip lp/hp 105 valve guide lp/hp 106 grease nipple 107 electrical gland 108 electrical cable per mt. 109 piston ring 1 set 110 7.5 hp motor winding 111 motor bearing 112 motor starter 113 motor contactor 114 overload relay (4 16 amp) 115 single phase preventer 116 v belt 1 set 117 motor pulley 118 pressure switch 119 non return valve ¾” 120 nipple for nrv 121 grease gum 122 activated alumina 123 timer 124 solenoid valve 125 pre filter 126 after filter 127 coil (sol. valve) 128 pressure gauge 129 valve 130 bolt (12nos.) 131 semi automatic control panel o2 &n2o 132 fully automatic control 133 diaphragm 2nd stage 134 seal tube 135 moulded tyre 136 wheel assay complete for anaesthesia machine 137 tyre for b/p 138 assay change over block 139 emergency khow for b/f 140 lever 141 gauge oxygen (0 250) kg/cm2 for b/basic 142 gauge nitrous (0 200) kg/cm2 143 bar clamping 144 assay pin & screw 145 nrv for o2 146 nrv for n20 147 front panel 148 diaphragm pipeline 149 saddle 28mm 150 saddle 22mm 151 saddle 15mm 152 saddle 10mm 153 tube flow meter oxygen 154 tube flow meter oxygen 155 plastic bracket for b/basic 156 top tray for b/basic 157 nrv cum now up valve 158 regulator oxygen 159 regulator nitrous oxide 160 yoke oxygen 161 yoke nitrous oxide 162 plug filter 163 beg mount 164 head brink expiratory valve 165 tube corrugated 166 adapter plug in hose 167 angle mount 168 bag rebreathing 2lt 169 bag rebreathing 1lt 170 assy. control valve oxygen 171 assy. control valve nitrous oxide 172 shoulder screw 173 piece distance 174 metallic tubing oxygen 175 metallic tubing nitrous oxide 176 metallic tubing for a/c 177 post gauge 178 bag rebreathing 0.5lt 179 humidefiere 180 angle 181 cylender key o2/n2o 182 oxigen nut 183 n2o nut 184 spanner 185 slyriner 186 alarm pipe 187 alarm albow 4mm/6mm 188 fasia 189 chang over 190 alaram 191 saddle 56mm 192 saddle 42mm 193 genitic valve 194 flow meter oxygen 195 oxygen mask 196 tail pipe nut o2/n2o 197 ward vacuumunit bottle 198 ward vacuum unit meter 199 handle 200 tie 201 screw 202 point o2/n2o/air/vacuum 203 clip 204 two way 205 adopter anesthesia trolly 206 point spring ...

Northern Railway - Uttar Pradesh

32560486 supply of poly carbonate cover for overload relaypoly carbonate cover for overload relay,poly carbonate cover for overload relay panel of demu & memu car bhel drg. no. 2583183001 v00....

Uttar Pradesh Jal Vidyut Nigam Limited - Uttar Pradesh

32543128 supply of heavy duty exhaust fan and dol starter for rihand hydro power station pipri sonebharda supply of heavy duty exhaust fan and dol starter for rihand hydro power station pipri sonebharda , supply of 600 mm heavy duty exhaust fan (900 rpm) , dol starter(2.4 3.8 amp overload relay, 12 amp contractor)...

Uttar Pradesh Rajya Vidyut Utpadan Nigam Limited - Uttar Pradesh

32448914 950 / pd ii / btps / anp / 2022 23 supply of magnetic contactors and mccbs for ventilation system of 2x500mw, btps, anpara , magnetic contactor type c12a, jem ac3 1.0, nke 8931, coil voltage 110 volt with 2no + 2nc contact with overload relay, type t11a t, jem iec bs , magnetic contactor type c35a, jem ac3 1.0, nke 8934, coil voltage 110 volt with 2no + 2nc contact with overload relay, type t35a t, jem iec bs , magnetic contactor type c20a, jem ac3 1.0, nke 8932, coil voltage 110 volt with 2no + 2nc contact & overload relay, type t20a t, jem iec bs , mccb ( ss50, 3 pole, 220vac, 25ka, 30a, 41 17963 ) , mccb ( sh50, 3 pole, 220vac, 85ka, 50a, 41 19466 ) ...

Firozabad Municipal Corporation - Uttar Pradesh

32383081 supply of electrical related material connection plate, panel starter, condenser, lugs, overload relay, meter, change over, main switch, cut out, single core pvc auto wire, aluminum cable, copper cable, kit set, rthermal timer, coil, contactor, motor pump set, pump set, pump, battery, starte switch, mccb, single indicator, joint patti, sand, oil, s.r no. 147 to 160 jyoti make for statrar set of base plate i.s.i set of terminal links abc i.s.i set of overload relay i.s.i set of connection links between contact and realy i.s.i terminal block with links i.s.i megnet coil rated 415v / ac i.s.i megent coil ( small loop ) i.s.i set of push button assly i.s.i type rz 11 having actualing time rang 3 to 12 secc i.s.i auxililary switch type 01 1 no+nc contacts i.s.i set of terminal serew and washer i.s.i full wairing starter i.s.i set of moving power contacts i.s.i set of fixed power contact i.s.i s.r no. 161 to 174 kilvarn make for statrar set of base plate i.s.i set of terminal links abc i.s.i set of overload reay i.s.i set of connection links between contact and realy i.s.i terminal block with links i.s.i megnet coil rated 415v / ac i.s.i mgenet coil ( small loop ) i.s.i set of push button assly i.s.i type rz 11 having actualing time rang 3 to 12 secc i.s.i set of terminal serew and washer i.s.i full wairing starter i.s.i auxililary switch type 01 1 no+nc contacts i.s.i set of fixed power contact i.s.i set of moving power contacts i.s.i s.r no. 175 to 188 bentax make for statrar set of base plate i.s.i set of overload reay i.s.i set of terminal links abc i.s.i set of connection links between contact and realy i.s.i terminal block with links i.s.i megent coil rated 415v / ac i.s.i megent coil ( small loop ) i.s.i set of push button assly i.s.i type rz 11 having actualing time rang 3 to 12 secc i.s.i auxililary switch type 01 1 no+nc contacts i.s.i set of fixed power contact i.s.i set of moving power contacts i.s.i set of terminal screw and washer i.s.i full wairing starter i.s.i s.r no. 189 to 201 advance make for statrar set of base plate i.s.i type rz 11 having actualing time rang 3 to 12 secc i.s.i set of terminal links abc i.s.i megnet coil rated 415v / ac i.s.i megnet coil ( small loop ) i.s.i set of connection links between contact and realy i.s.i terminal block with links i.s.i on / off push button assly i.s.i set of terminal serew and washer i.s.i loose oil leemered contract 25 amp i.s.i set of wairing full starter i.s.i set of fixed power contacts i.s.i set of moving power contacts i.s.i s.r no. 202 to 214 mug 30 make for statrar set of base plate i.s.i set of terminal links abc i.s.i set of overload relay i.s.i terminal block with links i.s.i megent coil rated 415v / ac i.s.i megnet coil ( small loop ) i.s.i set of moving power contacts i.s.i set of fixed power contacts i.s.i full wairing starter i.s.i type rz 11 having actualing time rang 3 to 12 secc i.s.i auxililary switch type 01 1 no+nc contacts i.s.i set of terminal and serew washer i.s.i on / off push button assly i.s.i s.r no. 215 to 229 bch make for statrar set of base plate i.s.i set of terminal links abc i.s.i set of overload reay i.s.i terminal block with links i.s.i megenet coil rated 415v / ac i.s.i megenet coil ( small loop ) i.s.i on / off push button assly i.s.i type rz 11 having actualing time rang 3 to 12 secc i.s.i auxililary switch type 01 1 no+nc contacts i.s.i plunger pir 60 amp aux switch i.s.i set of moving bridge i.s.i set of moving power contacts i.s.i set of fixed power contacts i.s.i set of terminal and serew washer i.s.i full wairing starter i.s.i...

Bharat Heavy Electricals Limited - Uttar Pradesh

32346660 e5920002 supply of star delta starter as per enquiry , star delta starter, suitable for 22kw ( 30 hp ) ac motor. relay 20 33a, 3 ph. with single phase preventer. note: 1 ) all components should be fixed in a sheet steel enclsure with front o pening. 2 ) enclosure should be suitably pain ted & have sufficient space inside the box to accomadate incoming / outgoing cables. 3 ) contractor: suitable rating should be 3 ph., 415v. 4 ) coil voltage 415v.ac. 5 ) fixing arrangement of starter should be suitable for wall / structure. 6 ) suitable earthing studs should be provided. make bch / c&s / l&t / seimens only. , fully automatic star delta starter, suitable for 50 hp ac motor, panel eith ammeter, voltmeter+vss, motor on & trip indicator, single p hase preventer having auto manual spp manual selection mode, as per is / iec60947 4 1, # pole 73a citation contractors rated at 415 vac, ct oprated thermal overload relay 37.6 to 60 a setting, rate voltage 415vac. note: 1 ) all components should be fixed in a sheet steel enclsure with front opening. 2 ) enclosure should be suitably painted & have sufficient space inside the box to accomadate incoming / outgoing cables. 3 ) contractor: suitable rating should be 3 ph., 415v. 4 ) coil voltage 415v.ac. 5 ) fixing arrangement of starter should be suitable for wall / structure. 6 ) suitable earthing studs should be provided. make bch / c&s / l&t / seimens only....

Uttar Pradesh Power Transmission Corporation Limited - Uttar Pradesh

32291702 retrofitting / repairing of marshalling box of 132 / 11 kv 20 mva t / f ii ( jeo mount make ) installed at 132 kv s / s gyanpur, under electy. trans. division i, prayagraj 1 the following work is requried for smooth operation of cooling fan installed on 20 mva t / f ii at 132 kv substation gyanpur, prayagraj. the details of work listed below : 2 supply and fixing of 01 no. main switch of 3p / 1w, 415 v, 16 a rating and 01 no. mcb of 4 pole, 415 v, 16a rating for 3 phase incoming supply for cooling fans. 3 supply and fixing of 01 no. 415 volt, 16a, 4 no. contactor for main supply of cooling fans installed on 20 mva t / f i work includes proper connection of contactor with acdb or ac cubical installed in the switchyard. 4 supply and fixing of fan control contactors of rating 230 v, 9a, 08 no. for auto function of cooling fans and relays of rating 230 v, 9a, 02 no+02nc for supply monitoring for cooling fans. 5 supply and fixing of 3 pole mcb of rating 230 v, 2a, on the rail fixed on the front side of marshaling box. 6 supply and fixing overload relay ( type 3us5000 ) of rating ( 0.5 2a ) for cooling fan of transformers on the front side of the marshaling box. 7 wiring of all interconnection with proper ferrules and lugs of suitable size with 4 mm2 flexible insulated copper conductors for power connection and with 2.5mm2 flexible insulated copper conductor for control connection in the marshaling box work. work includes supply and fixing of cable gland ( 19mm dia ) , wire, rail base, ferrule, lugs as required for proper operation of marshaling box. 8 supply and fixing of time delay relay ( on delay ) , of rating 230 volt, 1co for fan failure indication and stand by fan on indication of standard make. 9 supply and fixing of fan control switches for on / off control of fans ( on / off ) of ratings 415v, 10a of standard make. 10 supply and fixing of fan control contactors of type 3ts30 and rating 230 v, 9a, 6no+2nc for control operation of cooling fans of standards make. 11 prepartation of interconnection drawing & modification in marshaling box, wiring for new control and switching equipment to be installed in the cubical box. the work includes submission of drawing, connection / termination as approved by department ( in 3 copy ) 12 providing and fixing of terminal block ( b3 / m3 stud type ) of rating 415 v, 32a, for interconnection of fan control circuit, auxiliary protection ( oti, wti, buchhoize, oti, prv ) from field to relay panel and also for annunciation for indication of type of faults. all material provided by contractor at his own cost. 13 supply and fixing of 01 no. door switch of push off type with rating 230 v, 2a and 01 no. panel lamp ( led ) of 230 v, 8 w for proper illumination inside the marshaling box. 14 supply and fixing of 01 no. 5 pin socket switch box, 01 no. heater switch on / off type of 230 v, 40 w heater with metal glad and 01 no. thermostat of rating 230 v, ( 0 100c0 ) in side of marshaling box. work includes proper wiring of given sockets and switches....

Northern Railway - Uttar Pradesh

32229085 supply of design as per specificationdesign as per specification,design as per specification, supply, installation and commissioning of test bench for overload relays & olp relays for memu coaches, specifications as per annexure a. (note drawing to prepared as per specifications in annexure a and to be got approved by consignee befor manufacturing/supply. )...

North Eastern Railways - Uttar Pradesh

32193941 supply of supply of submersible pump set, isi marked motor rating 20 hp, discharge capacity 900 1200 lpm, discharge head 71 81 mtrs, nos of stage 05, outlet dia 100 mm, minimum 3 star rated, conforming to is: 8034 latest, motor is: 9283 latest, suitable for 415 volts(6 percent , 15 percent volts,), 50 hz/ 3 percent hz ,3 phase a.c supply.with control panel 20 hp, heavy duty 4 pole contractor type, overload relay, auto manual, with tripled indicator and single phase pror.supply of submersible pump set, isi marked motor rating 20 hp, discharge capacity 900 1200 lpm, discharge head 71 81 mtrs, nos of stage 05, outlet dia 100 mm, minimum 3 star rated, conforming to is: 8034 latest, motor is: 9283 latest, suitable for 415 volts(6 percent , 15 percent volts,), 50 hz/ 3 percent hz ,3 phase a.c supply.with control panel 20 hp, heavy duty 4 pole contractor type, overload relay, auto manual, with tripled indicator and single phase pror.,supply of submersible pump set, isi marked motor rating 20 hp, discharge capacity 900 1200 lpm, discharge head 71 81 mtrs, nos of stage 05, outlet dia 100 mm, minimum 3 star rated, conforming to is: 8034 latest, motor is: 9283 latest, suitable for 415 volts(+6 %, 15% volts,), 50 hz+/ 3%hz ,3 phase a.c supply.with control panel 20 hp, heavy duty 4 pole contractor type, overload relay, auto manual, with tripled indicator and single phase preventor....

Medical Stores Department - Uttar Pradesh

32140404 maintenance work of medical equipments and furniture of district rampur 1 servicing of h.p. sterilizer ( horizontal ) including leakage testing & removing steam leakage & cleaning and de scaling of water tank , pipe line with all materials, gasket etc. and giving trial at 30 p.s.i. at 120 c including calibration of all gauges & gadgets complete with all material labour t & p etc. 2 supply & replacementof 6 kw heatiing element of isi / escort or other reputed make. 3 supply & replacement of safety pressure valve of superior quality. 4 supply & replacement of 4 pole air contractor of reputed make 5 s / r of door rubber gaskit of superior quality. 6 supply & replacement of brass nickle brass plated outlet / inlet valve of superior quality 7 supply & replacement of door lock , dia pharam plate of brass with gasket and nut 8 supply & replacement of glass tube water lavel indicator with glass tube ( water lavel glass gauge ) of superior quality. ( as per dirc ) 9 supply & replacement pressure gauge / compound gauge of superiour quality. ( as per dirc. ) 10 s / r of 70 / 0076 heavey duty copper lead of 3 core with flexible pipe appx.4 mtr long with adopter and plug top of superior quality. 11 repair of sterlizer body complte with replacement of heavey thickness sheet patches by welding able to resist steam / water leakage etc. complete with material, labour and t&p etc. 12 servicing of h.p sterlizer ( ver ) including leakage testing & removing steam leakage, cleaning , descaling of water tank pipe line with all material gaskit etc. and giving trail at 30 psi and 120?c including calibration of all gauges and gadgets, complete with material, labour, t&p etc. 13 supply & replacement of 4.0 kw heatiing element of isi / escort or other reputed make. 14 supply & replacement of door rubber gaskit of superior quality. 15 supply & replacement of brass nickle plated fly nut & bolts of superior quality. 16 supply & replacement of safety pressure gauge of superior quality. 17 supply & replacement of safety valve spring type of superior quality. 18 supply & replacement of glass tube water lavel indicator ( water lavel glass gauge ) of superior quality. 19 supply & replacement of 40 / 0076 heavey duty copper lead of three core with flexible pipe appx.4 mtr long with adopter and plug top of superior quality. 20 repair of sterlizer body complte with replacement of heavey thickness sheet patches by welding able to resist steam / water leakage etc. complete with material, labour and t&p etc. 21 supply & replacement of 1.5 kw heating element of isi / escort or other reputedd make of electric auto clave 22 supply & replacement of steam pressur gauae of superior quality 23 supply & replacement of safety pressure valve type of superior quality. 24 supply & replacement of brass nickle plated fly nut & bolts of superior quality. 25 supply & replacement of door rubber gaskit of superior quality. 26 supply & replacement of 3 core copper wire lead with thre pin 15a plugtop and round adopter of sup. quality. 27 repair of instrument sterlizer including repair of body, cover and removing of leakage etc. with gas welding complete with mateia, labour, t&p etc. 28 supply & replacement of 1.5 kw heating element of isi / escort or other reputedd make ( cattl type ) 29 supply & replacement of round adopter / heating element connector of anchor / bajaj / crompton make. 30 supply & replacement of drain tap 31 supply & replacement of 23 / 0076 copper lead 4 mt long with 15 a, 3 pin top. 32 servicing of suction m / c complete with servicing of suction unit , and motor including leakage removing etc. complete with material , labour, t&p etc. 33 rewinding of suction motor, stator coil, complete with replacement of ball / bush bearing & condensor. 34 rewinding of compressor motor and overhauling of compressor, omplete wit material, labour, t&p etc. 35 s / r of brass bush of suction unit. 36 s / r of clutch plate assembly for motor. 37 s / r of suction bottle of superior quality. 38 s / r of haevy thickness rubber suction pipe of superior quality. 39 s / r of vaccume gauge of superior quality 40 s / rof toggle swith 41 s / r of filter 42 s / rof overload relay of sealed compressor unit. 43 s / rof 23 / 0076 copper lead 4 mtr. with 3 pin 15a plug top. 44 supply & replacement of shadowless bulb mercury coated of superior quality of shadowless lamp. 45 supply & replacement of shadowless bulb halogen of superiour quality 46 s / r glass cover of single bulb type of shadowless lamp. 47 s / r bulb holder of shadowless lamp. 48 s / r of transformer in 4 bulb type of of shadowless lamp / cealing light shadowless 49 s / r of transformer in 7 bulb type of of shadowless lamp / cealing light shadowless 50 checking / testing of internal wiring of shadow less lamp including repair if any adjustment of focuss replacement of burn copper lead with plug top. 51 nickle polishing of shadowless lamp shade copmlete with material, labour, t&p etc. 52 repair of single bulb shadowless lamp including replacement bulb holder, cable & top glass cover. 53 s / r of single bulb type shadowless lamp glass cover of reqd. size. 54 s / r of coil / strip type element etc for hot case / incubator. 55 s / r of thermostate switch of hot case incubator. 56 s / r of indicating lamp ( neon type ) of hot case incubator. 57 s / r of glass wood of door etc. of hot case incubator. 58 rewinding of motor stator coil complete with varnihing & replacement of carbon brush with spring & motor colot etc of cenrifuge machine. 59 repair of rotor and commutator etc complete in all res. of cenrifuge machine. 60 s / r of speed regulator of centrifuge m / c. 61 s / r of rubber gutka heavy thickness of centrifuge m / c. 62 repair of radiant warmer with change of temperature probe, heater, celling light, copper lead etc. complete in all respect. 63 servicing of hydrolic operation table including replacement of hydrolic oil, greasing of pump, wheel breake etc.complete with material, labour and t&p etc. 64 major repair of hydrolicoperation table including overhauling of hydrolic pump repair & replacement of required mech. component etc. complete with materiallabour t&p etc. 65 minor repair of non hydrolic operation table including replacement of sheet patches / pipe complete cutting, fixing and welding etc. 66 repair of non hydrolic operation table including of sheet pipe existing size of heavy thickness work include cutting and fixing with nut & bolts. 67 supply & fixingof new sealed compressure penumatic ( sealed ) for dental unit. 68 supply & fixingof new sealed compressure ( sealed ) for dental unit. 69 servicing of dental unit including leakege removing, including all material labour t&p etc. 70 supply & replacement of relay of compressor for dental unit. 71 supply and replacement of starting capacitorfor dental unit. 72 supply and replacement of runninging capacitor 80 / 120 mfd for dental unit. 73 supply and replacement of foot regulator switch. 74 repairing of compressure ( penumatic ) complete in all respect. 75 replacement of pressure switch. 76 replacement of pressure safety valve. 77 servicing of dental chair including replacement of hydrolic oil welding broken foot rest handle etc. 78 major repair of dental chair including overhauling of hydrolic pump repair of locking system & repair of other mechanical component etc. complete with material , labour t&p etc. 79 supply & fixing of new sealed compresure of window ac 80 servicing of window ac incuding leakage removing and replacement of filter complete with gas charging including material, labour, t&p.etc 81 supply & repair of relay of window ac 82 supply & repair starting capacitor of window ac 83 supply & repair running capacitor 80 / 120 mfdof window ac 84 rewinding of exhaust fan of window ac 85 supply & over load protection of window ac 86 cleaning of of window ac by chemical liquid. 87 repair of pcb complete in all respect. 88 supply & fixing of new sealed compresure of spilit ac 89 servicing of spilit ac incuding leakage removing and replacement of filter complete with gas charging including material, labour, t&p.etc 90 supply & repair of relay of spilit ac 91 supply & repair starting capacitor of spilit ac 92 supply & repair running capacitor 80 / 120 mfd of spilitw ac 93 rewinding of exhaust fan of spilit ac 94 supply & over load protection of spilit ac 95 cleaning of of window ac by chemical liquid. 96 supply & fixing of coper capillary 1 / 4 size. 97 supply & fixing of coper capillary 3 / 4 size. 98 repair of pcb complete in all respect. 99 servicing & repaire of refrigerator including leakage removing replacement of filter complete with gas & gas charging system with material, labour, t&p etc. 100 rewinding / overhauling sealed unit compressor of refrigeratior complete with material , labour, t&p etc. 101 s / r relay of compressor. 102 s / r of thermostate switch. 103 s / r of door switch. 104 s / r of 15 watt bulb. 105 s / r of door freezer spring of refrigerator. 106 s / r of door gas kit of refrigerator. 107 s / r of newsealed compresure. 108 s / r of newsealed compresure of water cooler. 109 servicing ofwater cooler incuding leakage removing and replacement of filter complete with gas charging including material, labour, t&p.etc 110 supply & repair of relay ofwater cooler 111 supply & repair starting capacitor ofwater cooler 112 supply & repair running capacitor80 / 120 mfd ofwater cooler 113 rewinding of exhaust fan ofwater cooler 114 supply & over load protection of water cooler 115 cleaning of of water cooler by chemical liquid. 116 supply & replacement of water tap. 117 repair of weighing m / c including replacement of spairing etc.complete with material, labour, t&p etc. 118 repairing of dressing drum including welding and replacement of kundli , kabza complete with material , labour, t&p etc. 119 s / r of arm pad rubber of bp instrument . 120 s / r of arm pad cloth of bp instrument . 121 s / r of air valve pressure of bp instrument . 122 s / r of mercury containr of bp instrument . 123 s / r of glass tube of bp instrument . 124 s / r of hinging pin ofbp instrument . 125 s / r of mercury triple refine complete with mercury & labour, t&p. etc. 126 servicing of room cooler including greasing ofexhaust fan & pump with leakage removing of water tank with soldering including replacement of perforated tape nozel complete with reveting etc. 127 rewinding of 18 / 20 stator coil of exhaust fan motor comp. with varnishing. 128 rewinding of 24 stator coil of exhaust fan motor comp. with varnishing baking. 129 s / rball bearing of 18 / 20 exhaust fan. 130 s / rball bearing of 24 exhaust fan. 131 s / r of condensor 4.0 mfd 18 / 20 exhaust fan. 132 s / r of condensor 8.0 mfd 24 exhaust fan. 133 rewindig of pump motor ( hor. ) complete with varnishing & leakage removing of pump. 134 s / r of ball bearing for horizental motor pump. 135 s / r of wood woolin cooler pads ( 3 nos ) including greasing and replacement of split pin, chuck nut etc.complete with material , labour, t&p etc. 136 supply & fixing of water lifting pump ( submersible type ) superiour quality complete in all respect. 137 servicing / checking / testing of ceiling / wall fan including greasing & replacement of split pin, check nut etc.complete with material , labour, t&p etc. 138 rewinding of 48 / 56, 60 watt, ceiling / wall fan statorcoil complete with varnishing & backing etc. 139 s / r of ball bearing for 48 / 56 60 w, ceiling fan . 140 s / r of condensor 2.5 mfd for 48 / 56, 60 w ceiling fan. 141 repaire of 1.0 / 0.5 kva voltage stablizer including replacement of relay, volt meter, socket and repair of transformer coil etc. with lead and 5a 3 pin top. 142 repaire of 4 / 5 kva voltage stablizer including replacement of relay, and electical circuit, volt meter, socket and repair of transformer complete with wire lead three core coper 40 / 0076 appx. 4 mtr with 3 pin top. 143 repaire of 10 kva servo stablizer including replacement of relay, and electical circuit, volt meter, socket and repair of transformer complete with wire lead three core coper 40 / 0076 appx. 4 mtr with 3 pin top. 144 repaire of 15 kva servo stablizer including replacement of relay, and electical circuit, volt meter, socket and repair of transformer complete with wire lead three core coper 40 / 0076 appx. 4 mtr with 3 pin top. 145 repair of iron bed including welding straightning, tightning, of iron jal withits repairing complete with material, labour, t&p etc. 146 repair of iron bed including replacement of heavy gauge pipe legs, cutting welding of req.size with material. 147 s / r of bed spring. 148 s / r of new jal strip type complete with welding complete with, labour, t&p etc. 149 supply & replacement of rubber shoes for iron bed 150 supply & fixing of hook with welding etc. 151 repair of fowler bed / hard bed with miner repair. 152 repair of fowler bed including replacement of damage pipe heavy gauge & repair of jaal wire ( g.i wire ) complete in all resp. 153 repair of hard bed with replacement of sheet patches & welding etc. 154 repair of bed side locker including welding & replacement of kabja, kundli, complete in all respect. 155 major repair of bed side locker including replacement of damage sheet heavy thickness locker complete in all resp. with fixing & welding. 156 s / r leg of bed side locker with welding. 157 s / r shoes of locker. 158 miner repair of strature including replacement of sheet pathes with welding etc. 159 major repair of strature includind replacement of full sheet heavy thickness complete withmaterial labour, t&p etc. 160 repair of strature trolly including replacement of condute pipe heavy gauge complete with welding etc. 161 s / r of caster wheel 6 dia complete with fixing. 162 s / r of caster wheel 4 dia complete with fixing. 163 repair of iron stool including replacement of damage sheet , pipe & welding etc. 164 repair of screen stand including replacement of damage condute pipe & fixing with welding etc. 165 repair of i.v stand including replacement of damage pipe with labour, t&p etc. 166 repair of spitoon stand including replacement of damage pipe with welding etc. 167 miner repair of instrument / medicine / dressing trolly including welding with req. pipe etc. 168 major repair of instrument / medicine / dressing trolly complete with replacement of glass sheet of appx.30x18 size & 6mm thick complete etc. 169 miner repair of instrument cabinet including welding & replacement of sheet patches / handle etc. 170 repair of inst.cabinet including replacement of glass with cutting & fixing etc. sheet patches / handle etc.reqd. pipe copmlete in all resp. 171 s / r of iron legs of instrument cabinet. 172 s / r lock of instrument cabinet of superior quality. 173 repair trolly of oxygen cylender including replacement of damage pipe / sheet / strip / with weld. etc. 174 miner repair of examination table including replacement of sheet patches / pipe with welding etc. 175 repair of examination table including replacement of full sheet complete with fixing etc. 176 miner repair of labour table including replacement of sheet patches / pipe with welding etc. 177 repair of labour table including replacement of full sheet complete with fixing etc. 178 repair of wheel chair including repair of foot rest with welding & oiling, greasing, of main wheel etc. replacement of sheet patches / pipe with welding etc. 179 repair of wheel chair including replacement of main wheel with rubber and other repair work complete with material labour t&p etc. sheet patches / pipe with welding etc. 180 repair of foot step including replacement of sheet patches / pipe with welding etc. 181 repair of iron bench including replacement of sheet patches / pipe with welding etc. 182 repair of iron bench 3 seater including replacement of sheet patches / pipe with welding etc. 183 repair of steel almirah ( big ) including replacement of damage sheetwith welding etc.complete with material, labour t&p etc. 184 s / r handle of almirah. 185 repair of steel almirah ( small ) ) including replacement of damage sheetwith welding etc.complete with material, labour t&p etc. 186 s / r leg of almirah. 187 reapair of steel tableincluding replacement of sheet patches / pipe , repair of lock etc. complete with material, labour t&p etc. 188 repair of steel chair including replacement of pipe with welding etc. 189 repair of steel reckincluding replacement of sheet patches & angle iron with nut and boltwith welding etc. 190 spray painting of operation table with two coats of synthetic enamel paint ( burger or any equivalent superior quality ) work include with complete scrapping, surface making smooth complete with material, labour, t&p etc. 191 as same abovebut for shadowless lamp. ( ceilling type ) 192 as same abovebut for shadowless lamp. ( 4 bulb type ) 193 as same as above but for refrigerator with stand. 194 as same as above but for refrigerator ( full size. ) with stand. 195 as same as above but for desert room cooler 18 exhaust fan room cooler cabinet. 196 as same as above but for ceilling fan 56 comp. with down rod & regulator. 197 as same as above but for suction m / c mtp. 198 as same as abovebut for water cooler. 199 as same as above but for exhaust fan. 200 spray painting of iron bed with two coats of synthetic enamel paint ( burger or any equivalent superior quality ) work include with complete scrapping, surface making smooth complete with material, labour, t&p etc. 201 as same as above but for bed side locker. 202 as same as above but for instrument cabinet ( big ) 203 as same as above but for instrument cabinet ( small ) 204 as same as above but for iron stool. 205 as same as above but for bed side screen stand. 206 as same as abovebut for strature with trolly. 207 as same as abovebut for iron bench. 208 as same as above but for examination table. 209 as same as above but for medicine / dressing / ins. trolly. 210 as same as above but for i.v stand. 211 as same as abovebut for spitoon stand. 212 as same as abovebut for trolly of oxygen cylender. 213 as same as above but for wash basin stand. 214 as same as above but for steel almirah ( big ) . 215 as same as above but for steel almirah ( small ) . 216 as same as abovebut for steel reck. 217 as same as above but for steel table. 218 as same as above but for steel chair. 219 as same as above but for wheel chair. 220 as same as abovefor foot step. 221 as same as abovefor labour table....

National Thermal Power Corporation Limited - Uttar Pradesh

31983906 procurement of 240v dc battery charger spares for chp stage 2 area forntpc tanda. , cap fltr:450v:4700 micro farad , choke, 0.78mh at 80a dc, make:hblnife , synch.transformer: 10va, 230 / 0 10v, 1a , control transformer , mains transformer , control xymr:250va, 415v 230v , thyrstr / scr: 445a, 1200v piv , heat sink eia1717, 225mm , blocking diodes forbattery chargers , thyrstr:156a 1800v:wth h / snk eia1717 150 , selector switch in 4position 10a, 250vac , power contactor 150a lc1 f115 , coil 415 v ac for cont. cat 3tya 24 150a , isolat swtch 3p neutrl, 200a 415v general , bc:chhabi:rotary switch 2p , 1p 2way on off cam type s / w 240v ac 16a , toggle sw 16a for make up wtr cntrl pnl , rotary cam switch 2pole on / off 2t 26b , selector switch 1 p 2 way 16a, 240v ac , selectr swtch:4pos:10a 110ac:kaycee , ac voltmeter ( is:1248 ) range: 0 500v , ammeter 0 150a ct ratio 150 / 1a class 1.5 , dc voltmeter: 0 400v, cl 0.5, 96x96 sqmm , dc ammeter range: 0 250a, class:unspec , relay base pnl 11pin 3c / o , boost relay with base 6a, 24vdc , ct for i / p current meas.150a / 0.1a, 1va , trimpot, multiturn, 20k?, for 60 kva ups , shunt 300a / 75mv , rc card for batt.chrgr#69 00003; hbl , bc:hbl ps 24v 32a:pulse transmitter card , dc dc converter for batt.chrgr#69 00076 , connector card for batt.chargr;hbl power , overload relay 85 135 amp , bc:hbl ps 24v 32a:control card , fuse fail card#69 00123, make: hbl power , sub led card for batt.charger; hbl pwr , misc elect device &comp rc card 69 00001 , multi alarm card for batt.charger; hbl , relay card for batt.charger, make: hbl , analog output card, model no.;140aco13000 , comm. card for battery charger; hbl , led display card 69 00084 ( rev 0 ) , frc connector 14 pin , frc connector 26 pin , frc connector 34 pin , aux.multi alarm card for batt.chargr;hbl => limited...

North Eastern Railways - Uttar Pradesh

31420959 supply of electrical itemelectrical item,thermal overload relay contactor mounted type without adopter f series within built single phase protection range 2.2 to 3.1 amp as per cat no mc 318 ana 3j of m/s bch, cat no. cs96355ooqo of m/s l&t ,type code reference no ta 25du3.1m (order code isaz211201r2031) of m/s abb or equivalent make siemens ,conf. to rdso spec no elps/spec/ac/04 (rev 3) with amendment no.1 suitable for blower fan motor of rmpu ac coaches....

North Eastern Railways - Uttar Pradesh

31420630 supply of electrical itemelectrical item,thermal overload relay contactor mounted type without adopter f series with built in single phase protection range 7.5 to 11 amp. as per cat no mc 318 ana 3p of m/s bch or equivalent make l&t ,abb and siemens ,conf. to rdso spec. no. elps/spec/ac/04 (rev 3) with amndt no. 1 suitable for compressor protection of rmpu type ac coaches....

North Central Railway - Uttar Pradesh

31367488 supply of hv overload relay(qlm).hv overload relay(qlm).,hv overload relay(qlm) with mechanical interlocking arrangement having 2 nc interlock type di as per clw specn.no. clw.es.r 27 alt z....

Bharat Heavy Electricals Limited - Uttar Pradesh

31363058 supply and supervison of etc of 10ton double girder eot crane for sjvnl arun3, nepal project supply and supervison of etc of 10ton double girder eot crane for sjvnl arun3, nepal project , supply cranes : eot crane double girder 10t ( 10t double girder eot alongwith all accessories as per technical specification ) , supply cranes : eot crane – tools & tackles ( as per annexure m of technical specification ) , services cranes : supervision of erection testing and commissioning of 10t double girder eot crane of 10t double girder eot crane supervision of erection testing & commissioning on per day basis for the days present at site on certification by bhel site incharge. price shall be inclusive of charges for lodging, boarding, medical, insurances etc. , services cranes : to & fro travel charges to & fro travel charges on per visit basis for all visits as per site requirement. local transportation between hotel and site to be arranged by contractor. , spares cranes : eot crane pair of brake shoe with lining for each size of brake used viz. d.c. operated e.m, or hydraulic thruster operated , spares cranes : eot crane pair of brake linings with rivets for each size of brake used , spares cranes : eot crane main springs for each size of brake used , spares cranes : eot crane brake coils for each size of brake used , spares cranes : eot crane thruster of each size used , spares cranes : eot crane pair of oil seals for each gear box used on crane , spares cranes : eot crane contactors of each size used , spares cranes : eot crane fixed & moving contacts of each size contactor used , spares cranes : eot crane 3 nos. coils for each size of contactor used , spares cranes : eot crane overload relay for each motor , spares cranes : eot crane 3 no. fuse links of each sizes used on crane , spares cranes : eot crane 1 printed circuit breaker of each size and type , spares cranes : eot crane complete set of lamps for lightning and signals , spares cranes : eot crane fuse links of each size used , spares cranes : eot crane segment of dsl including fitting, jointing, clamping etc. ( remark: equivalent to 1 phase installed length for each location ) , spares cranes : eot crane lt bearings ( remark: 50% of installed bearings in each crane ) , spares cranes : eot crane ct bearings , spares cranes : eot crane motor of each type and rating , spares cranes : eot crane flood light illumination ( remark:50 % of installed at each location ) , spares cranes : eot crane load cell , spares cranes : eot crane indication lamp of dsl , spares cranes : eot crane mccb and fuses ( remark:1 set each ) , spares cranes : eot crane auxiliary relay, contactor and timers ( remark:5 nos. each ) , spares cranes : eot crane communication card / cable ( remark:one set for one complete crane ) , spares cranes : eot crane i / o card ( remark:one set for one complete crane ) , spares cranes : eot crane processors ( remark:one set for one complete crane ) , spares cranes : eot crane indicating lamps ( remark:one set for one complete crane ) , spares cranes : eot crane vvvf drive ( remark:one set for one complete crane ) ...

Ministry of Housing and Urban Affairs - Uttar Pradesh

31239791 bids are invited for energy meter, , 32a mcb, , 6a mcb , 63a mcb , 10a mcb , indicator lights or lamps ( led ) , minimum ip 40 ingress protection , indicator lights or lamps ( led ) , minimum ip 65 ingress protection , current transformer dual purpose 10 100 / 50 / 5 5a , 16a mcb , electronic timer relay, , relay module , 230v, 40a, 4 pole power contractors , punchingmachine, , astronomical timer , tools storagecabinet ( almirah ) , thermal capacitor , cylindrical cell , thermal overload relay , mild steel vacuum pump , thermaloverload relay. spare parts of panels for failure rectification total quantity : 1436...

National Thermal Power Corporation Limited - Uttar Pradesh

31219915 procurement of c and s make spares for lt switchgears of ntpc rihand andsingrauli , direct mounting o / l relay 30 40 a , thermal o / l relay, 23 32amp, c&s make , power contactor 3p 415v ac 230v ac 65a , 18 25amp over load relay c&s make , thermal o / l relay, 12.0 18.0a, c&s make , thermal o / l relay, 10 13 amp, o&s make , thermal o / l relay, 7.0 10.0 amp, c&s make , addon block for c&s contactor 2no+2nc , main contact set for lc1 f400 tc make , main contact set for lc1 f150a tc make , thermal o / l relay, 5.5 8.0amp, c&s make , thermal o / l relay, 4 6 amp, c&s make , swtch dis fuse:13947pt3:h duty tpn , aux contacts block 800a , thermal overld relay:a 2.5 4.0a , thermal o / l relay, 2.5 4.0a, c&s make , thermal o / l relay, 1.6 2.5a, c&s make , fuse unit 32 a , switch fuse unit 250 amp , thermal o / l relay, 0.63 1.0a, c&s make , thermal overload relay:a1 1.6a , thermal o / l relay, 1.0 1.6a, c&s make , o / l relay lr1 d09 306 c&s make 1 1.6 a , led indicating lamp.col red <3w , indicat lmp led yellow 22.5mm 240v ac1w , switch fuse unit 32a, cssf32d3, c&s make , power contactor 400a, 415 volt cv 110vac , operating handle:c&s make:sfu:400amp , power contactor 3p 415v ac 110v ac 63 a , overload relay lr1 200 315amp tc make , 160 250amp over load relay c&s make , 125 200amp over load relay c&s make , power contactor 3p 415v ac, 110v ac, 80 a , 100 160amp over load relay c&s make , power contactor 3p, 115 acv110 ac, tc , 66 80amp over load relay c&s make , pwr contactor 415v 330a 110v ac tc , thrm overlod rely amp 65 105ac&s , power contactor 3p 415v ac 110v ac 185 a , overload relay auto / manual 45 65amp , thermal o / l relay, 30 40 amp, c&s make , power contactor 3p 415v ac 110v ac 265 a , thermal o / l relay, 38 50 amp, c&s make , 200a moving outgoing power contacts , 200a fixed outgoing power contacts , 100a moving outgoing power contacts , front drawout type modules, 0.25kw , position indi switch c&s acb up to 1600a , incoming male power contact of 250a , sfu:c&s:spare s / w cssf250d3 , spare kit;pwr contr;16a;tc;lc1d173;la5d , main cont lc1f 185 contactor 185a c&s , main contacts for lc1f265 la5 fh431 , main contacts for lc1f185 la5 fh431 , pwr cont;3p 415vac;115a;coil:240vac;tele , powercontactor 16a240vac lc1d173 a60 , pwrcontr;240vac265a;2no+2nc;telemec;lc1f , power contactor coil:110vac, lc1d80 80a. , aux. contactor cv 110v ca2dn1229 , front drive with door interlock8uc62 , bim o / l;200 315a;telemech:lr1 f315 , thermal o load relay18 25 a , thermal o load relay2.5 4.0a , thermal overld relay:a1.6 2.5a , thermal o load relay0.4 63 a , rely th o / l:0.63 1a:tr2d09305 , bim o / l;75 105a;660vac;telemech lr1f105 , thermal o load relay0.63 1a , thermal overload relay:a1 1.6a , contactor, type:lc1d173f with 110v ac , air break switch 400a type cssdf400d3n , air break switch type cssdf125d3n 125a , main fixed contacts for 2500a acb , air break switch 32a type cssdf32d3n , air break switch type cssdf63d3n 63a , pwr contctr:c&s:m contct set lc1d323f , l / mechnsm 2000 2500a typacb lowermech25c , l / mechnsm typ 6 16b / d p lowermech16b , acb main isolating contact ( jaw ) , mic 25d , acb main isolating contact ( jaw ) , mic 08d , ckt / drawout terminals, ckttml 25d , ckt / drawout terminals, ckttml 08d , lt acb shunt coil 220v dc, avh s 220md , lt acb closing coil 220v dc, avh c 220md , acb single pole unit 2500a, cond unit 25d , acb single pole unit 800a, cond unit 8d , spring charg motor;acb ah30dcs;3200a;c&s , closng coil model avh c 116, 250vdc acb , position indicator switch for c&s acb...

East Central Railway - Uttar Pradesh

30798407 supply of hv overload relay etchv overload relay etc,over load for rectifier (qrsi) di type relay as per clw spec.no. clw/es/r 27 alt.z aal pt.no. ka210013r00181...

Department Of Heavy Industry - Uttar Pradesh

30576333 bids are invited for boqauto extension if any seller submits price in last 15 minutes, the rawill be auto extended by 15 minutes ( a maximum of300 times ) total quantity : 1 1 supply cranes : eot crane double girder 6t 2 supply cranes : eot crane – tools & tackles 3 spares cranes : eot crane long travel axle bearings 4 spares cranes : eot crane long travel gearbox bearings with sleeves 5 spares cranes : eot crane long travel end shaft bearings 6 spares cranes : eot crane long travel coupling 7 spares cranes : eot crane long travel seals for gear box 8 spares cranes : eot crane long travel brake shoes 9 spares cranes : eot crane long travel brake springs 10 spares cranes : eot crane long travel brake shoe liners 11 spares cranes : eot crane cross travel axle bearings 12 spares cranes : eot crane cross travel gearbox bearings with sleeves 13 spares cranes : eot crane cross travel end shaft bearings 14 spares cranes : eot crane cross travel coupling 15 spares cranes : eot crane cross travel seals for gear box 16 spares cranes : eot crane cross travel brake shoes 17 spares cranes : eot crane cross travel brake springs 18 spares cranes : eot crane cross travel brake shoe liners 19 spares cranes : eot crane main hoist pulley bearings 20 spares cranes : eot crane main hoist bearings for rope drum 21 spares cranes : eot crane main hoist bearings for gear box 22 spares cranes : eot crane main hoist seals 23 spares cranes : eot crane main hoist brake shoes 24 spares cranes : eot crane main hoist brake springs 25 spares cranes : eot crane main hoist brake shoe liners 26 spares cranes : eot crane disc pad for disc brake 27 spares cranes : eot crane power contactor of each rating 28 spares cranes : eot crane overload relays of each rating 29 spares cranes : eot crane mccb/mpcb of each rating 30 spares cranes : eot crane push button of each type 31 spares cranes : eot crane vvvf drive module card 32 spares cranes : eot crane bearings for main hoist motor 33 spares cranes : eot crane bearings for cross travel motor 34 spares cranes : eot crane bearings for long travel motor 35 spares cranes : eot crane motor of each type and rating 36 etc eot crane erection, testing & commissioning at site ...

Meja Urja Nigam Private Limited - Uttar Pradesh

30561491 procurement of cands make overloads, cradle terminals and sfu procurement of cands make overloads, cradle terminals and sfu , thermal bmr, 0.40 0.63a, c&s, lr1 d09304. , thermal bmr, 0.63 1.0a, c&s, lr1 d09305. , thermal bimetallic relay , thermal overload relay 2.5 4 a , 4 6 amp, over load relay, lr1 d09310, c&s. , bimetallic overload relay 5.5 8 a , thermal bmr, 10 13a, c&s, lr1 d12316. , thermal bmr, 13 18a, c&s, lr1 d16321. , thermal overload relay , thermal bmr, 23 32a, c&s, lr1 d32353. , thermal bmr, 30.0 40.0 a, c&s, lr1 d40355. , 38 50 amp, over load relay, lr1 d63357, c&s , thermal bmr, 57 66a, c&s, lr1 d63361. , 66 80 amp, over load relay, lr1 d80363, c&s , thermal overload relay 65 105 a , cradle terminal, rating 8n 10n , cradle terminal , rating 25d , 400a, tp, sfu, make c&s, model cssdf400d3. => limited...

Department Of Atomic Energy - Uttar Pradesh

30477606 bids are invited for 1 bimetallic relay/thermal overload relay 0.3 0.5a (3ru2116 0fb0) , 2 bimettalic relay/thermal overload relay 0.5 1a/ 0.63 1a (3ua5000 oj) , 3 bimetallic relay/thermal overload relay 1.0 2a (3ua5200 1b) , 4 bimetallic relay/thermal overload relay 1.6 2.5a (3ua5200 1c) , 5 bimetallic relay/thermal overload relay 12.5 20a (3ua5200 2b) , 6 bimetallic relay/thermal overload relay 16 25a new (3ua5800 2cz2) , 7 bimetallic relay/thermal overload relay 25 40a (3ua5800 2ez2) , 8 bimetallic relay/thermal overload relay 2.5 4a (3ua5200 1e) , 9 bimetallic relay/thermal overload relay 3.2 5a (3ua5000 1f) , 10 bimetallic relay/thermal overload relay 32 50a (3ua5800 2fz1) , 11 bimetallic relay/thermal overload relay 5.0 8a new (3ua5200 1h) , 12 bimetallic relay/thermal overload relay 8.0 12.5a (3ua5200 1k) , 13 bimetallic relay/thermal overload relay 10 16a (3ua5500 2a) total quantity : 1...

North Eastern Railways - Uttar Pradesh

30436496 supply of 1 thermal overload relay, current setting range 66 amp.2 thermal overload relay, current setting range 45 amp.3 thermal overload relay, current setting range 30 amp.4 thermal overload relay, current setting range 24 amp. 5 thermal overload relay, current setting range 20 amp. 6 thermal overload relay, current setting range 14 amp.7 thermal overload relay, current setting range 09 amp.1 thermal overload relay, current setting range 66 amp. 2 thermal overload relay, current setting range 45 amp. 3 thermal overload relay, current setting range 30 amp. 4 thermal overload relay, current setting range 24 amp. 5 thermal overload relay, current setting range 20 amp. 6 thermal overload relay, current setting range 14 amp. 7 thermal overload relay, current setting range 09 amp.,thermal overload relay, current setting range 66 amp. to 110 amp. as per l&t type mn5 & cat no. ss94137ooko conforming to is/iec 60947 , thermal overload relay, current setting range 45 amp. to 75 amp. as per l&t type mn5 & cat no. ss94137oojo conforming to is/iec 60947 , thermal overload relay, current setting range 30 amp. to 50 amp. as per l&t type mn5 & cat no. ss94136oogo conforming to is/iec 60947 , thermal overload relay, current setting range 24 amp. to 40 amp. along with mounting kit as per l&t type mn2 & cat no. ss94145oofo & ss94700oooo conforming to is/iec 60947 , thermal overload relay, current setting range 20 amp. to 33 amp. along with mounting kit as per l&t type mn2 & cat no. ss94145ooeo & ss94700oooo conforming to is/iec 60947 , thermal overload relay, current setting range 14 amp. to 23 amp. along with mounting kit as per l&t type mn2 & cat no. ss94144oodo & ss94700oooo conforming to is/iec 60947 , thermal overload relay, current setting range 09 amp. to 15 amp. along with mounting kit as per l&t type mn2 & cat no. ss94142oobo & ss94700oooo conforming to is/iec 60947 => limited...

Uttar Pradesh Rajya Vidyut Utpadan Nigam Limited - Uttar Pradesh

30249313 procurement of 180kw and 37kw dk 21t type module of seal air fan and faph for htps, kasimpur. procurement of 180kw and 37kw dk 21t type module of seal air fan and faph for htps, kasimpur. , 180kw complete module ( in two separate parts ) type dk21tmotor rated 180kwmodule consisting of following components 100% interchangable with corresponding existing modules of m / s c&s mcc part 1 separate sfu module consisting of following components ( a ) one ( 1 ) 630 a, triple pole complete sfu with on / off switch, raotary handle ; ith 630a, ue 415v 50hz, ui 750v; ( b ) three ( 3 ) numbers hrc power fuses ( c ) one ( 1 ) 1no+1nc aux contact, part 2; separate control module consisting of following components ( a ) one ( 1 ) triple pole power contactor, 440 / 415 vac, 50 hz, 630a, coil voltage 110v ac; ( b ) one ( 1 ) ct operatedthermal overload relay with ct, range 315 500a; ( c ) three ( 3 ) indicating lamps with resistors and coloured lenses.; ( d ) three ( 3 ) hrc control fuses 6a, 415v ac ch type withbakelite fuse holder for size 14x51 mm fuse carrier & base conforming to is:1300, is:13703 / iec 269, bs:771, ; ( e ) two ( 2 ) auxiliary contactors, coil voltage 110v ac, 2no+2nc, ; ( f ) two ( 2 ) coupling relays ( o / e / n type ) with base suitable for 24v dc 500o; ( g ) one ( 1 ) digital energy meter suitable accordingly; ( h ) one ( 1 ) earth leakage relay suitable accordingly; ( i ) three ( 3 ) current transformers for metering, 350 / 1a, class 1, insu class b, ; ( j ) one ( 1 ) , current transducer, aux :110vac, input: 0…1a, 50hz, output 1: 4…20ma, 50hz, rmax 750 ohms, output 2: 4…20ma, 50hz, rmax 750o; ( k ) one ( 1 ) , add on blocks, 2no+2nc, ( other specifications as enclosed in tender document ) , 37kw complete module ( type dk21 non reversible motor rated 37kwmodule ) consisting of following components ( 100% interchangable with corresponding existing modules of m / s ge mcc ) ( a ) one ( 1 ) 160a, triple pole mccb ( technical specification attached ) ; ( b ) one ( 1 ) triple pole power contactor, 440 / 415 vac 45kw rated current 140a, ie 80a, ith 140a, ui 1000v, ac 3ph ( c ) one ( 1 ) electronic motor protection relay , din rail mounted, aux supply ( control power ) :44 to 300 vac / dc, conforming to as per iec 60947 withfollowing protections, over current, thermal over load, locked rotor, earth fault, under current, short circuit, phase reversal, phase lock, phase loss ( d ) three ( 3 ) indicating lamps with resistors and coloured lenses. ( e ) three ( 3 ) hrc control fuse with base, link, carrier. ns 4, 415v ac, 80ka gg ( f ) two ( 2 ) auxiliary contactors rl4r22e, 2no+2nc, ( g ) two ( 2 ) coupling relays ( o / e / n type ) with base suitable for 24v dc. ( h ) one ( 1 ) digital energy meter suitable accordingly, ( i ) three ( 3 ) current transformers for protection 150 / 5a, va 2.5 class 1, insu class b, ( j ) one ( 1 ) current transformers for metering. 100 / 1 a, va 5.0, insu class b ; ( k ) one ( 1 ) , current transducer, aux :110vac, input: 0…1a, 50hz, output 1: 4…20ma, 50hz, rmax 750 ohms, output 1: 4…20ma, 50hz, rmax 750 ohms; ( l ) four ( 4 ) add on blocksith 10a, 2no+2nc ( other specifications as enclosed ) ...

Bharat Heavy Electricals Limited - Uttar Pradesh

30215538 supply and etc of 10t eot crane for arun 3 (sapdc), nepal project supply and etc of 10t eot crane for arun 3 (sapdc), nepal project , supply cranes : eot crane double girder 10t (10t double girder eot alongwith all accessories as per technical specification) , supply cranes : eot crane – tools & tackles (as per annexure m of technical specification) , spares cranes : eot crane pair of brake shoe with lining for each size of brake used viz. d.c. operated e.m, or hydraulic thruster operated , spares cranes : eot crane pair of brake linings with rivets for each size of brake used , spares cranes : eot crane main springs for each size of brake used , spares cranes : eot crane brake coils for each size of brake used , spares cranes : eot crane thruster of each size used , spares cranes : eot crane pair of oil seals for each gear box used on crane , spares cranes : eot crane contactors of each size used , spares cranes : eot crane fixed & moving contacts of each size contactor used , spares cranes : eot crane 3 nos. coils for each size of contactor used , spares cranes : eot crane overload relay for each motor , spares cranes : eot crane 3 no. fuse links of each sizes used on crane , spares cranes : eot crane 1 printed circuit breaker of each size and type , spares cranes : eot crane complete set of lamps for lightning and signals , spares cranes : eot crane fuse links of each size used , spares cranes : eot crane segment of dsl including fitting, jointing, clamping etc. (remark: equivalent to 1 phase installed length for each location) , spares cranes : eot crane lt bearings (remark: 50% of installed bearings in each crane) , spares cranes : eot crane ct bearings , spares cranes : eot crane motor of each type and rating , spares cranes : eot crane flood light illumination(remark:50 % of installed at each location) , spares cranes : eot crane load cell , spares cranes : eot crane indication lamp of dsl , spares cranes : eot crane mccb and fuses(remark:1 set each) , spares cranes : eot crane auxiliary relay, contactor and timers(remark:5 nos. each) , spares cranes : eot crane communication card/cable(remark:one set for one complete crane) , spares cranes : eot crane i/o card(remark:one set for one complete crane) , spares cranes : eot crane processors(remark:one set for one complete crane) , spares cranes : eot crane indicating lamps(remark:one set for one complete crane) , spares cranes : eot crane vvvf drive(remark:one set for one complete crane) , etc work at site for 10t double girder eot crane...

Uttar Pradesh Metro Rail Corporation - Uttar Pradesh

30136506 bids are invited for energy meter, supply of energy meter, accuracy class 0.2s, 440v having minimum measuring value kwh, kva, kvar, md etc. model no. elite 440, make secure or equivalent , 32a mcb, supply of 32a mcb, 4 pole with 3pp 415 volt, model no. fp c32, make abb or equivalent , 6a mcb supply of 6a mcb, 1 pole with 1pp 240 volt, model 3. no. sb201m c6, make abb or equivalent , 63a mcb supply of 63a mcb, 4 pole with 3pp 415 volt, model no. 1sys274012r0634, make abb or equivalent , 10a mcb supply of 10a mcb, 1 pole with 1pp 415 volt, model no. sh201m c10, make abb or equivalent , indicator lights or lamps ( led ) , minimum ip 40 ingress protection supply of indicator lights or lamps ( led ) , minimum ip 40 ingress protection, operating voltage ac / dc 220v, color blue 100 pcs, red 200 pcs, green 100 pcs, yellow 100 pcs, amber 100 pcs, make any popular brand, colour blue , indicator lights or lamps ( led ) , minimum ip 65 ingress protection supply of indicator lights or lamps ( led ) , minimum ip 65 ingress protection, , operating voltage ac / dc 9 220v, model no. 3eplbr8l220ac or equivalent, color blue 10pcs, red 20 pcs green 10 pcs, yellow 10 pcs, protection class ip65, colour yellow , current transformer dual purpose 10 100 / 50 / 5 5a supply of current transformer dual purpose 10 100 / 50 / 5 5a, accuracy class c, 230 / 415v, winding copper, cooling medium oil immersed, no. of secondary two, standard accuracy class of measuring 1 , standard accuracy class of measuring of special application 0.55 , 16a mcb supply of 16a mcb, 415 volt single pole with 1pp, intantaneous tripping range c, model no. sb201m c16, make abb or equivalent , electronic timer relay, supply of electronic timer relay, model no. 12 d1etm1, make minilec or equivalent , relay module supply of relay module, model no. my4n gs, make omron or equivalent. , 230v, 40a, 4 pole power contractors supply of 230v, 40a, 4 pole power contractors with 1 no+1 nc auxiliary contact, model no. my4n a 40 30 1080, make abb or equivalent, warranty 1 year , punching machine, supply of punching machine, operating manually, a4 spiral binding, no. of punch ( min ) 36 nos., punching capacity 12nos. model no. fs spiral, make gmp or equivalent. , astronomical timer supply of astronomical timer, operating voltage 230v, 50hz, power rating 1phase, 6 kw / 43a, model no. t2ddt7, make gic or equivalent, warranty 1year , tools storage cabinet ( almirah ) supply of tools storage cabinet ( almirah ) , size 1150x760x430mm, shelves 3no., material m s sheet, sheet thickness of locker .07 mm, length of glass sheet 400 mm, width of glass sheet 305 mm, material of lock brass & steel finish, material of keys steel, waaranty 1 year , thermal capacitor supply of thermal capacitor, 55+6 mfd for air conditioner, make concap or equivalent. , cylindrical cell supply of cylindrical cell, size aa ( r6 ) , 1.2v, 1.5ah, make duracell or equivalent, warranty 3 year , thermal overload relay supply of thermal overload relay, operating voltage 415v, rating 40 70a, warranty 2 year , mild steel vacuum pump supply of mild steel vacuum pump, air tank capacity 10 liter, rating 1 hp, vaccum ( hg ) 100 ( mmhg ) , power supply single phase, make crompton, model no 15876, or equivalent, warranty 1 year , thermal overload relay. supply of thermal overload relay, operating voltage 415v, rated current 10 16a, make l&t or equivalent. warranty 1 year total quantity : 1...

Indian Air Force - Uttar Pradesh

29841528 bids are invited for relay 24v dc108a (q3) , control relay (aux contractor) (q3) , phase sequence relay (q3) , bridge rectifier (q3) , relay socket type (q3) ,overload relay (q3) , selector switch (q3) total quantity : 23...

Ministry Of Petroleum And Natural Gas - Uttar Pradesh

29647745 bids are invited for sply and instln of cable tie size:150mm , suply and instln of cable tie size:100mm , supply and instln of cable tie size:300mm , sply and instaln of cable tie size:250mm , sply and installation of cable tie size:200mm , pvc tape steel grip , earthing wire,cu,6mm2 pvc,1100v, havells/polycab , smf battery 65ah exide , flp jb, 170x170 fcg, heavy duty, with tc & peso appr , flp junction boxb, 100x100,4way fcg, heavy duty, with tc & peso appr , led tube light, 4feet rat:20w , led light tube 2 feet rat:18w , six ampere nh type fuse link,6a 415vac,siemens , ten ampere nh type fuse link,10a 415vac,siemens , sixteen ampere nh type fuse link,16a 415vac,siemens , thirty two ampere nh type fuse link,32a 415vac,siemens , sixty three a nh type fuse link,63a 415vac,siemens , two a hf type fuse link, 2 a 415vac,siemens , four a hf type fuse link, 4 a 415vac,siemens , ten a hf type fuse link,10 a 415vac,siemens , six a hf type fuse link, 6 a 415vac,siemens , sizteen a hf type fuse link,16 a 415vac,siemens , thirty two a hf type fuse link, 32a 415vac,siemens , twenty five a hf type fuse link,25 a 415vac,siemens , twenty ampere nh type fuse link,20a 415vac,siemens , twenty five ampere nh type fuse link,25a 415vac,siemens , twenty a hf type fuse link,20 a 415vac,siemens , sixty three a hf type fuse link,63 a 415vac,siemens , sply of thermal overload relay upto 50 a , four pole mcb,lexic,legrand 415v,63ap,10ka,4p , three pole mcb,lexic,legrand 415v,32ap,10ka,3p , two pole mcb,lexic,legrand 240v,10ap,10ka,1p+n , single pole mcb,lexic,legrand 240v,16ap,10ka,1p+n , 11kv rubber hand gloves with tc , lt rubber gloves with tc , lt insulation mat,rubber wide:900mm,1.1kv , ht insulation mat,rubber wide:900mm,11kv , 415v, caution board caution board, acrylic , 11kv, danger/caution board acrylic board , sup 15 w led false ceiling havells/syska , sup 50x6 mm gi strip gi flat strip , gi flat 25x3...

Uttar Pradesh Rajkiya Nirman Nigam Limited - Uttar Pradesh

29601808 tender for electrical work &p 2 fire fighting work fire pumps and accessories: supplying, installation, testingand commissioningof electric driven main fire pump suitablefor automatic operationandconsistingoffollowing, completeinall respects, as required :a ) horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to is 1520.b ) suitable hp squirrel cage induction motor, tefc, synchronousspeed1500rpm, suitableforoperation on415volts, 3phase50hz, acsupplywithip55 protectionforenclosure, horizontalfootmountedtype with class f insulation, conforming to is 325.c ) suitable hp squirrel cage induction motor, tefc, synchronousspeed1500rpm, suitableforoperation on415volts, 3phase50hz, acsupplywithip55 protectionforenclosure, horizontalfootmountedtype with class f insulation, conforming to is 325.d ) m.s. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. e ) suitablecementconcretefoundationdulyplastered with anti vibration pads. f ) 2850 lpm at 70 m headnote: * the head of the pump is selected in a manner soastogivea minimum 3.5kgf / cm 2 pressureat the highest / farthest point. 3 supplying, installation, testingandcommissioningof diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : ( diesel driven pump ) a ) horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to is 1520.b ) suitablehp, 1500rpmwatercooledwithradiator, diesel engine conforming to relevant is standard completewithautostartingmechanism, 12 / 24volts electricstartingequipment, dieseltank, exhaustpipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. c ) m.s fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. d ) suitablecementconcretefoundationdulyplastered and with anti vibration pads.2850 lpm at 70 m headnote: * the head of the pump is selected in a manner soastogivea minimum 3.5kgf / cm 2 pressureat the highest / farthest point. 4 supplying, installation, testingandcommissioningof electricdrivenpressurisationpumpsuitablefor automaticoperationandconsistingoffollowing, complete in all respects, as required : ( jockey pump ) a ) .horizontaltype, multistage, centrifugalpumpofcast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to is : 1520. b ) .suitablehpsquirellcageinductionmotortefctype suitableforoperationon415volts, 3phase50hz ac supply with ip 55 class of protection for enclosure, horizontalfootmountedtypewithclass finsulation, conforming to is : 325. c ) .m.s.fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required.d ) .suitablecementconcretefoundationdulyplastered and with anti vibration pads.180 lpm at 70 m head 5 control panels: fabrication, supply, insallation testing & commissioning of electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick crca sheet, compartmentalisedwithhingedlockabledoors, dustandverminproof, powdercoatedofapproved shade after 7 tank treatment process, cable alley, inter connection with suitable sizecopperconductor cable / solidcopper strip, havingswitchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitableformainfirepump, pressurisationpump& dieselpumpsetcompleteaspercpwdspecification withfollowingincomingandoutgoings, suitablefor operationon415v, 3phase, 50hzacsupplywith enclosure protection class ip 42 as required :incomings:a ) 630a, 50ka4 pole mccb, ics=100% icu rating digital voltmeter 0 500v with selector switch ammeter ( 0 630 a ) with selector swtich & cts etc.b ) ledtyperybphaseindicatinglamps, on, off, trip indicating lampsset of copperbus bar 800ampsoutgoings: main fire pump :200amp, 50katpnmccb, ics=100%icu, withfully automatic star / delta starter suitable for 75 hp pump with overloadprotection, currentsensingtypesinglephase preventorcompletewithallacceessoriesandinternal wiringrequiredforautomaticoperation, selectorswitch for local / remote, auto / manual / off operation. 2 setsjockey pump:100 amp, 50ka tpn mccb, ics=100% icu, with suitable hp fully automatic star / delta starter with overload protection, currentsensingtypesinglephasepreventor complete with all acceessories and internal wiring requiredforautomaticoperation, selector switchfor local / remote, auto / manual / off operation. 2 setsdiesel engine controla ) control for diesel engine comprising automatic / manualselctorswitch&3attemptsstarting device, timersandrelaysasrequired, pushbuttons, start / stop in manual modeb ) indicatinglampforhigh / lowlub.oilpressure, high water temp and engine on indicationc ) batterychargersuitbalefor12v / 24vdcwithboost and trickle selector switch, 0 30 v dc volt meter, and 020 a dc ammeter all standard relays and accessories for automatic operation of diesel engine.system controller: designing, supply, installation, testingand commissioning of system controller to control operation of main electric fire pump, diesel pump, pressurization pump, terrace pump in sequence as per specification consisting of relays, timers. sensors, annunciation windowforfaultindication, complete as per specification 6 providinglaying, testing&commissioningofcclass heavydutymspipeconformingtois1239 / 3589i / c fittingslikeelbows, tees, flanges, tapers, nutsbolts, gasketsetc.ingroundincludingwelding, excavation& providingcementconcreteblocksassupports, anticorrosivetreatmentwithcoaltar / asphalttapeasper is10221, refillingthetrenchetc.offollowingsizes complete as required. 200 mm. dia ( wall thickness = 6.3 mm ) 7 150 mm. dia 8 providing, laying, testing&commissioningof cclass heavydutymspipeconformingtois3589 / is1239 includingwelding, fittingslikeelbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall / ceiling with suitable clamp / support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25 mm dia 9 32 mm dia 10 40 mm dia 11 50 mm dia 12 65 mm dia 13 80 mm dia 14 100 mm dia 15 150 mm dia 16 providing, laying, testing&commissioningofbclass heavydutyg.i.pipeconformingtois1239including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall / ceiling with suitable clamp / support frame and painting with two ormorecoatsofsyntheticenamelpaintofrequired shade complete as required: 25 mm 17 32 mm 18 40 mm 19 50 mm 20 65 mm 21 80 mm 22 100 mm 23 150 mm 24 supplyingandfixingsingleheadedinternalhydrant valve with instantaneous gunmetal / stainless steel coupling of 63 mm dia with cast iron wheelisi marked conformingtois5290 ( type a ) withblank gunmetal / stainless steel cap and chain as required :single headed gunmetal 25 supplying and fixing single headed external yard hydrant valve with 1 no. 63 mm dia instantaneous fm gunmetal / stainlesssteel couplingand cast iron wheel, isimarked, conformingtois5290 ( typea ) withblank gunmetal / stainless steel cap and chain as required :single headed gunmetal 26 supplying, fixing, testing and commissioning of butterfly valve of pn 1.6 rating with bronze / gunmetal seat duly isi markedcompletewithnuts, bolts, washers, gaskets conforming to is 13095 of following sizes as required :80 mm dia 27 100 mm dia 28 150 mm dia 29 supplying, fixing, testing&commissioningofdouble flangedsluicevalveofratingpn1.6withnonrising spindle, bronze / gunmetalseat, isimarkedcomplete with nuts, bolts, washers, gaskets and conforming to is 780 of following sizes as required : 80mm dia 30 100mm dia 31 150mm dia 32 200mm dia 33 250mm dia 34 supplyingandfixingorificeplatemadeoutof6mm thick stainless steel ( grade 304 ) with orifice of required sizetobefitted betweenflange&landingvalveof externalandinternalhydrantstoreducepressureat the outlettothe levelof 3.5kg / cm2 complete as required. 35 providing, installation, testingandcommissioningof non returnvalveoffollowingsizesconfirmingtois: 5312 complete with rubber gasket, gi bolts, nuts, washers etc.as required.100mm dia 36 150mm dia 37 200mm dia 38 providing, installation, testingandcommissioningof stainlesssteely strainerfabricatedoutof1.6mm thickstainlesssteel, grade304, sheetwith3mmdia holes with stainless steel flange.150mm dia 39 200mm dia 40 supplying and fixing 63 mm dia, 15 m long rrl hose pipewith63mmdiamaleandfemalecouplingsduly boundwithgiwire, rivetsetc.conformingtois636 ( type a ) as required : gun metal 41 supplying andfixing first aidhosereelwithms constructionspraypaintedinpostofficered, conformingtois884completewiththefollowingas required. a ) . 20mmnominalinternaldiawaterhosethermoplastic ( textile reinforced ) type 2 as per is: 12585 b ) .20mmnominalinternaldiagunmetalglobevalve& nozzle. c ) .drum and brackets for fixing the equipmets on wall.d ) .connections from riser with 25 mm dia stop gun metal valve & m.s. pipe and socket. e ) .40 m 42 supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter sizenozzle conforming to is 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : gun metal 43 supplyingandfixingoffirebrigadeconnectionof cast iron body with gun metal male instantaneous inlet couplingscompletewithcapandchainasreqd.for suitabledia ms pipe connectionconforming to is 904 as required :2 way 100 mm dia m.s. pipe 44 4 way 150 mm dia m.s. pipe 45 3 way 150 mm dia m.s. pipe 46 supplying and fixing air vessel made of 250 mm dia, 8 mm thick ms sheet, 1200 mm in height with air release valveontopandflangedconnectiontoriser, drain arrangementwith25mmdiagunmetalwheelvalve withrequiredaccessories, pressuregaugeand paintingwith synthetic enamel paint of approved shade as required. 47 providing, fixing, testing & commissioning of 15mm dia quartzoidbulbtypesprinklersofrating68degree centigrade with required accessories :pendent sprinkler 48 upright sprinkler 49 horizontal side wall sprinkler 50 concealed sprinkler 51 providing & fixing of pressure switch in m.s. pipe line including connection etc. as required. 52 providing& fixingflowswitchinfollowingsizesm.s. pipe including connection etc as required. 53 100mm dia 54 150mm dia 55 providing, fixing, testing & commissioning of installationcontrolvalveofcastironbody, brass / bronzeworking partscomprisingofwater motor alarm, bronzeseatclapper, clapperarmand hydraulicallydrivenmechanicalgongbelltosound continuousalarmwhenthewetriser / sprinklersystem activates, pressuregauges, emergencyreleases, strainer, pressureswitch, cockvalvecompletewith drainvalveandbypass, testcontrolbox, ballvalves, ms pipe of required size, flanges, orifice plate, gasket etc of follwing sizes asrequired : 150mm dia 56 supplying, installation, testing & commissioning of sprinklerflexiblepipe ( ullisted ) ofstainlesssteel complete with 15 npt on reducer thread with maximum working pressure of 175 psi test pressure of 875psi ( burst ) withbranchline ( inlet ) 25mmnpt malethreadtosprinklerhead ( outlet ) 15mmnpt femalethreadwithreducer, nipple, 2sidebrackets, center bracket, stockbar of following sizes complete as required.700mm 57 1000mm 58 1200mm 59 1500mm 60 providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required ( e&m ) 61 providing and fixing ms cabinet ( size 750x600x250 mm ) fabricated from 16 gauge ms sheet with full front glass door & locking arrangement for pad lockwith suitable shelves for keeping 25 nos. spare sprinklers & one no. spanner properly fixed in shelves. cabinet shall be painted with enamel paint of approved shade. ( cost shall include 20 nos. spare sprinklers ( 5 nos side wall 20nos pendent, one no. spanner and 5 rolls of teflon tape ) . note: all valves shall be of pn16 rating 62 portable fire extinguishers: providing & fixing of isi marked ( is:15683 ) portable fire extinguisher, carbondioxide type flat base including valve, discharge hose of not less than 10 mm dia. 1 m long & complete in all respects including initial fill with co2 gas confirming to is:307 1966 filled to a filling ratio of not more than 0.667 of not more than 0.667 and wall suspension bracket capacity 4.5 kg 63 6 kg. abc powder type fire extinguishers are manufactured and marked to indian standard is: 15683. suitable first aid appliance for fighting fires in class a, b & c fire that is wood, textile, flammable liquids & gases. 64 providing and fixing mechanical foam type fire extingushers consisting of welded m.s. trolley mounted cylindrical body, squeeze lever discharge valve fitted with pressure discharge hose, discharge nozzle, trolley etc., isi marked as per is:is:13386 finished externally with red enamel paint.capacity 50 lit ( d.g.room ) 65 providing and fixing carbon di oxide fire extingushers trolley mounted with all accessories internal discharge tube, high pressure discharge hose, discharge nozzle, isi marked as per is:2878 finished externally with red enamel paint. capacity 22.5 kg. 66 boq d: plumbing pump & equipmentswater supply, drainage, pumps & equipment :providingand fixing centralized water level controller cum indicator system, as per the following details:centralised plc control panel : along with touch screen display board ( min. 8 diag. size ) along with all accessories for complete controls & indication. panel shall be made out of crca sheet min. 2mm thick having necessary interlocks, i / os, required number of repeater amplifiers, all audio visual alarms as required specifications as listed below. an emergency stop push button shall be provided in the panel. the panel shall have modbus compatibility for seamless bms / bas integration and shall be of approved make. the complete system control matrix, wiring diagram, slds and technical details shall be submitted by the vendor and gotten approved before commencement of execution of works. water level indicators cum controllers :working on hydrostatic pressure measurement principle made of stainless steel for installation on storage tanks, and capable of providnig 4 to 20 ma analog signal compatiblewith plc signal inputs and completeas per working requirements for details of equipment below. all control outputs to mcc panel shall be included as per requierments. a ) .fire static underground tanksb ) .real time water level indication monitoring 67 v. low level audio visual alarm at less than 25% total capacity.raw water underground tanksreal time water level indication monitoring v. low level audio visual alarm at less than 30% total capacity. v. high level audio visual alarm at more than 100% total capacity.auto cut in of tubewell pumps at 35%auto cut out of tubewell pumps at 95% 68 auto cut out of raw water pumps at 35%domestic water underground tanks real time water level indication monitoring v. low level audio visual alarm at less than 30% total capacity. v. high level audio visual alarm at more than 100% total capacity. auto cut in of raw water pumps at 35% 69 auto cut out of domestic water pumps at 35% flushing water underground tanks at stpreal time water level indication monitoringv. low level audio visual alarm at less than 30% total capacity.v. high level audio visual alarm at more than 100% total capacity.auto cut in of raw water pumps ( from stp ) at 35% 70 auto cut out of flushing water pumps at 35% domestic water overhead tanksreal time water level indication monitoring v. low level audio visual alarm at less than 30% total capacity. 71 v. high level audio visual alarm at more than 100% total capacity. flushing water overhead tanksreal time water level indication monitoring v. low level audio visual alarm at less than 30% total capacity. 72 v. high level audio visual alarm at more than 100% total capacity. 73 providing complete testing kit with all chemicals complete suitable for conducting test on water quality.the test kit shall be suitable to measure tds, ph, hardness, iron content and other parameters 74 hydro pneumatic pumping system for domestic supply to fixture ( toilet kitchen ) : providing, fixing and testing of packaged type skid mounted hydropneumatic system with variable frequency drive type comprising of : ( i ) vertical, inline multistage centrifugal pumping set with stainless steel ss 304stage casing and ss 304 impellers with stainless steel ss 304 shaft as per iecstandards and gjl250 cast iron suction& discharge casing, connected to tefc ventilated induction motor of2 pole, 2900rpm, suitable for 400 / 440 volts, 3 phase, 50 hz a.c. supply. ( ii ) pressure vessel of non corrosivefrp composite construction lined with nsf and / or fda listed material, likehigh density polyethylene with fully replaceable polyurethane. air cell burstpressure of minimum of 5 times the vessel operating pressure and cycle tested for 2, 50, 000 cycles. ( iii ) control panel with programmable logic controller ( plc ) for cyclic operation of pumps + variable frequency drive. the pump workingsequence should change after every operation.contractor overload relays and mcbs should confirm to iec 898 – 1995 / specifications. blinking indications for pumps start, trip, low level trip, health supply should be provided in the panel along with the ammeter& voltmeter. control panel should also consist of cooling fan. ( iv ) pressure switches bellowtypefittedwithmicro switch and having maximum pressure and differentialscaleshould confirming bs 6134 standards and ip55 protection class. ( v ) all required ball valves, non return valves, flexible connectors etc. and all required accessories, heavy duty s.s 316 manifold to make the system completely operational as a skid mounted system. ball valves tobe used should be hot pressed brass ot 58withstainless steelballand p.t.f.eseal and o ring. nrvs to be used shouldbewithspringsando ring arrangement. ( vendor to submit performance curves and technical catalog of the proposed model for review & information ) complete manifold system shall be factory aasembled & totally mounted on a common base frame with following duties:note: contractor to note that the suction header is required to have inlet connection from the puddle flange @ water tanks and to the pump suction. provision of delivery header is required to have outlet connection from the pumps. suitable outlet flanges from the delivery mainfold / header shall be provided as required.a.for domestic water supply for club & benquet hall: no. ofpumps :1 ( 1 working +1 standby ) capacity: 350 lpm each pump head: 55 meters apx. hp ( motors ) : 3 hp location : plumbing plant room 75 for flushing water relift pump :no. ofpumps :1 ( 1 working +1 standby ) capacity: 250 lpm each pump head: 55 metersapx. hp ( motors ) : 2 hplocation : stp plant room 76 garden hydrents & floor washing relift pump:providingand fixing vertical, inline multistage centrifugalpumpingset ( complete manufactured skid mounted arrangement with manifold and accessories ) withstainlesssteelss 304stage casingandss 304impellerswith stainless steel shaft as per iec standards and gjl250 cast iron suction & discharge casing, connected to tefc ventilated induction motor of 2 pole, 2900 rpm, suitablefor 400 / 440 volts, 3 phase, 50 hz a.c. supply with pressure gauge and with gunmetal isolationcocks, vibrationelimination pads etc. complete with base and frame, nuts and boltsandnecessary rcc foundations as per requirementasper instructionsandpumpshallhave following duty:no. ofpumps :2 ( 1 working +1 standby ) capacity: 200 lpm each pumphead: 45 metersapx. hp ( motors ) : 4 hplocation : stp plant room 77 supply, installation, testing & commissioning of continuous duty submersible centrifugal non clogging drainage pumps of efficiency of approved make complete with 3 phase motor with all necessary protection and mechanical seal etc. complete with all ancillaries including float type level controllers, electrical control panels fabricatd from 14 gauge crca sheet volt meter ammeter with selector switch, tpmcb, 5 va cl : cts, phase indicating lamps protected by 2 amp sp mcb, dol starter, necessary wiring, cable alleys, earthing, interlocking, starter with automatic float type level controller, providion of high level alarm, sequence timer, potential free contact to starter for connection to bas, both pumps may run simultaneously at pre determind level. ( 1 working + 1 standby ) vendor to submit proposed pump model with duty curve.a ) . for wtp & stp plant room drainage :flow rate : 450 lpm head : 15 mtssolid handling : 100 mmlocation : sump of basement purpose : plant room & general area drainage moc : ss body ss impeller & shaft 78 b ) .for basement drainage : flow rate : 450 lpm head : 15 mts solid handling : 100 mmlocation : sump of basement purpose : basement area drainage moc : ss body ss impeller & shaft 79 c ) .manhole cover for u.g tanks and sumps :supplying and fixing c.i. cover without frame for manholes :560mm diameter c.i cover ( heavy duty ) the weight of the cover to be not less than 108kg. 80 f ) .providing and fixing stainless steel ladder, wall mounted of 4m height ( app ) for underground tanks complete with flanged ends and inserts ( removable type ) made of 38mm / 42mm dia 16 g s / s 304 quality pipe made as per international quality standards of approved shape and size with non skidding stepsat 300mm vertical spacing, completeas directed by the engineer in charge. 81 water treatment plant: providing & fixing vertical, inline multistage centrifugalpumping set ( complete manufactured skid mounted arrangement with manifold and accessories ) with stainlesssteel ss 304 stage casing and ss 304 impellers with stainless steel shaft as per iec standards and gjl250 cast iron suction & discharge casing, connected to tefc ventilated induction motor of 2 pole, 2900 rpm, suitable for 400 / 440 volts, 3 phase, 50 hz a.c. supply with pressure gauge and with gunmetal isolation cocks, vibration elimination pads etc. complete with base and frame, nuts and bolts and necessary rcc foundations as per requirement as per instructions and pump shall have following duty:a ) .for club building only : no. ofpumps: 2 ( 1 working + 1 standby ) flow rate :150 lpm each head : 30 mtsrequired for : filter feed pump in plumbing plant room ( 1working + 1standby ) 82 providing and fixing vertical pressure filter with dual media filter ( comprising of 600mm bed depth of graded sand gravel and 600mm bed depth of anthracite ) fabricated from high performance m.s plate of minimum 8mm thick for shell & 10mm thickfor dished ends with top and bottom flanged openings including top and bottom hub and lateral distribution and collection system complete with initial charge of filter media, face piping, valves, accessories, painting, testing and commissioning complete. ( tested to 6 kg / m2 ) discharge : 150 lpm filtration rate: 17500 lit. / m2 / h discharge : 150 lpm suggested dia app.: 0.90 m 83 activated carbon filter ( domestic water ) : providing and fixing vertical activated carbon filter comprising ofactivated carbon filter media fabricated from high performance m.s plate of minimum 8mm thick for shell & 10mm thickfor dished ends with top and bottom flanged openings including top and bottom hub and lateral distribution and collection system complete with initial charge of filter media, face piping, valves, accessories, epoxy painting, testing and commissioning complete. ( tested to 6 kg / m2 ) discharge :100 lpm filtration rate: 15000 lit. / m2 / h suggested dia app.: 0.60 m 84 providing, fixing, testing & commissioning of msep water softening plant ( suitable for 3 kg / sqcm workingpressure ) complete with initial charge with t 40 na resin, multiport valve with built in ejector for controlling all operations ) , regeneration system and hdpe tank, pressure gauge at inlet, outlet and back wash ( each with isolation cock ) , valves, fittings and water hardness testing kit & associatedworks. softener shall be suitable for the following duty:note:the successful contractor will have to carry out a test of raw water from all the sources of water for the commercial, residential & apartment at their own cost from a reputed lab as approved by the engineer in charge / consultant. on the basis of these results the contractor has to submit his shop drawings, design calculations and specifications accordingly.please note that it is ultimately the responsibility of the contractor to provide treated water for different use as per international standard as given in the attached guidelines. raw water hardness: 500 mg / ltreated water hardness:100 mg / l regeneration period:12 hrs.capacity : 100 lpm 85 supplying, installing, testing and commissioning of dosing system ( for domestic water treatment plant ) consisting of one hdpe tank of 100 litres capacity with a positive displacement diphragm dosing pump having variable flowrate of 0 6 lph. the motor shall be suitable for operation at 240 v / single phase / 50 hz. supply. the pump shall be supplied complete with necessary polypropylene piping, valves, strainers, low level switch andinjection fittings. the pump shall be speed & stroke control asialmi / equivalent make. the cost shall be inclusive of providing salt for the testing and operation of system before handover to the owner. 86 plumbing panel: design, manufacture, assembly, wiring, testing at works and supply to site of following panels / distribution boards / switch boards. the boards shall be designed and fabricated as per general specifications, technical details, specifications and notes as part of this tender / boq and relevant bis codes. ( any load veriation in system as technical document of manifactureno cost shall be paid extra for system requirments ) ip rating: ip 54 incomer:1 no. 250 a 25 ka, 3p mccb of motor duty only magnetic release. ( adjustable magnetic release upto 250a mccb or micro processor based release above 250a mccb ) .incomer metering & indication: a ) .415v / v3 / 110v / v3pts, cast resin type, 3 phase for metering & indications, suitable rated 6a, tp mpcb of the fault withstand capacity as of the panel on the primary side of pt & suitable rated 6a, tp mcb on the secondary side of pt.b ) .r, y, b phase indication lamps ( 110v ) led type c ) .cast resin metering cts for each phase of class 1 accuracy & of suitable burden & ratio d ) .1 no. digital vaf + pf meter ( 110v ) ( *with / without rs 485 port ) bus bars : 400a, tp, aluminium bus bars of electrolytic grade with heat shrinkable sleeves 25 ka. control transformer & control circuiting for starters / contactors & indication lamps : a ) .1 no. 415v / 55 0 55vcast resin dry type control transformer of adequate va burden to take care of load of all the contactor coils. ( transformer with primary taps at ± 2.5%, ± 5%, 50 hz, centre tap earthed ) .b ) .suitable rated 6a, dp, mpcb of the fault withstand capacity as of the panel for control circuiting for contactors coils on the primary side of control transformer & suitable rated 6a, dp mcb on the secondary side of control transformer.c ) .110v control circuiting d ) .110v control supply healthy indication ( led type ) .outgoings: a ) .dol starter comprising the following ( for upto 2 hp motors ) for raw water pumps / treated water transfer pump / flushing water transfer pump / borewell / soft water transfer pump / for pump room fresh air fan / for pump room exhaust air fan:a ) . for 1hp. ( 2 nos. ) ( chamical dosingpump ) b ) .type 2 co ordinationc ) . 1 no. suitable rated tp mpcb, 10ka, with inbuilt o / l relay & inbuilt spp feature ( site adjustable ) d ) .suitable sized 3p contactor with 2 no & 2 nc auxiliary contactse ) . on / off / trip indication lamps ( 110v ) ( led type ) f ) .on / off push buttons g ) star delta timerh.2 pole a / m selector switch for bms application i ) .suitable rated single cast resin ct for metering on y phase, of class 1 accuracy & of suitable burden & ratio. j ) .digital ammeter k ) .on / off trip / a / m potential free contacts for bmsl ) .control wiring terminals for auto operation through potential free contacts ofwater tank level controllers.b ) .dol starter comprising the following ( for 3 hp to 5 hp motors ) for raw water pumps / treated water transfer pump / flushing water transfer pump / borewell / soft water transfer pump / for pump room fresh air fan / for pump room exhaust air fan :a ) for 4 hp. ( 2 nos. ) ( for pump room exhaust air fan ) b ) type 2 co ordination c ) 1 no. suitable rated tp mpcb, 25 ka, with inbuilt o / l relay & inbuilt spp feature ( site adjustable ) d ) suitable sized 3p contactor with 2 no & 2 nc auxiliary contactse ) on / off / trip indication lamps ( 110v ) ( led type ) f ) 2 pole a / m selector switch for bms application g ) suitable rated single cast resin ct for metering on y phase, of class 1 accuracy and of suitable burden & ratioh ) digital ammeter with inbuilt selector switch i ) digital ammeter j ) on / off trip / a / m potential free contacts for bmsk ) control wiring terminals for auto operation through potential free contacts ofwater tank level controllers.c ) .dol starter comprising the following ( for 7.5 hp to 10 hp motors ) for raw water pumps / treated water transfer pump / flushing water transfer pump / borewell / soft water transfer pump / for pump room fresh air fan / for pump room exhaust air fan:a ) for 7.5hp. ( 2 nos. ) ( raw water / filter feedpump ) b ) . for 6 hp. ( 2 nos. ) ( soft water reliftingpump ) c ) .type 2 co ordinationd ) .1 no. suitable rated tp mpcb, 10 ka, with inbuilt o / l relay & inbuilt spp feature ( site adjustable ) e ) .suitable sized 3p contactor with 2 no & 2 nc auxiliary contacts f ) .on / off / trip indication lamps ( 110v ) ( led type ) g ) .on / off push buttons ( with lockable off ) h ) . pole a / m selector switch for bms application i ) .suitable rated cast resin cts for metering on each phase, of class 1 accuracy and of suitable burden & ratioj ) .digital ammeter with inbuilt selector switch k ) on / off trip / a / m potential free contacts for bms l ) .control wiring terminals for auto operation through potential free contacts ofwater tank level controllers. d ) .star delta starter comprising the following ( for 12.5 hp to 25 hp motors ) for raw water pumps / treated water transfer pump / flushing water transfer pump / borewell / soft water transfer pump / for pump room fresh air fan / for pump room exhaust air fan:a ) .12.5 hp. ( 3 nos. ) ( tubewells pump ) b ) .type 2 co ordinationc ) .1 no. suitable rated tp mpcb, ka, without inbuilt o / l relay ( only magnetic ) d ) .suitable sized 3p contactors ( star, delta & run contactors ) with 2 no & 2 nc auxiliary contactse ) suitable o / l relay with inbuilt spp f ) .on / off / trip indication lamps ( 110v ) ( led type ) g ) .2 pole a / m selector switch for bms application h ) .suitable rated cast resin cts for metering on each phase, of class 1 accuracy and of suitable burden & ratioi ) digital h inbuilt selector switch j ) on / off trip / a / m potential free contacts for bms k ) control wiring terminals for auto operation through potential free contacts ofwater tank level controllers. feeders ( without starters ) for hydronumatic pump panels :1 no. suitable rated 15 ka, tp, mpcb without inbuilt o / l relay & with 1 no + 1 nc auxiliary contacts & on indication lamp 110v ( led type ) for 10 hp sump pump panel. suitable rated cast resin cts for metering on each phase, of class 1 accuracy and of suitable burden & ratio. digital ammeter with inbuilt selector switch. feeders ( without starters ) for sump pump panels : 2 no. suitable rated 15 ka, tp, mpcb without inbuilt o / l relay & with 1 no + 1 nc auxiliary contacts & on indication lamp 110v ( led type ) for 15 hp sewarage sump pump panel. suitable rated cast resin cts for metering on each phase, of class 1 accuracy and of suitable burden & ratio. digital ammeter with inbuilt selector switch. feeders ( without starters ) for r.o water booster pump panels : 1 no. suitable rated 10 ka, tp, mpcb without inbuilt o / l relay & with 1 no + 1 nc auxiliary contacts & on indication lamp 110v ( led type ) for 3 hp r.o waterbooster pump panel. suitable rated cast resin cts for metering on each phase, of class 1 accuracy and of suitable burden & ratio. digital ammeter with inbuilt selector switch.spare starter feeders ( without starters ) with same components as described in above written similar starter feeders:5 hp motors, dol starter ( 2 nos. ) ( spare feeders ) spare motor feeders ( without starters ) with same components as described in above written similar feeders: 2 no. suitable rated 15 ka, tp, mpcb without inbuilt o / l relay & 1 no + 1 nc auxiliary contacts & on indication lamp ( 110v ) led type for 10 hp feeder. suitable rated cast resin cts for metering on each phase, of class 1 accuracy and of suitable burden & ratio. digital ammeter with inbuilt selector switch. 1 no. suitable rated 10 ka, tp, mpcb without inbuilt o / l relay & 1 no + 1 nc auxiliary contacts & on indication lamp ( 110v ) led type for 5 hp feeder. suitable rated cast resin cts for metering on each phase, of class 1 accuracy and of suitable burden & ratio. digital ammeter with inbuilt selector switch.vendor can also consider integrated total co ordinated starter upto 15hp.plumbing panel as described above. 87 sump pump panel ( upto 5.0hp motor ) : a ) .it shall control two pumps p 1 and p 2. the operation sequence will be as under :b ) .p 1 & p 2 to stop at l 1 c ) .p 1 to start at l 2 d ) .p 2 to start at l 3 ( at l 3 both pump will be running ) audible alarm at l 4 ( 50 mtr range ) .e ) .hooter for annunciation ( solid state buzzer ) f ) .where l 1 < l 2 < l 3 < l 4 ( level of water in the sump ) ( probes / sensors to control operation ) g ) .there shall be selector switch to interchange the starting sequence between p1 & p2. ( selection mode ) important features : sump pump panel shall have following essential features: r, y, b phase indicating lamps with backup. auto / manual selector switch. starter on / off & high level indications, digital ammeters for both pumps. mpcb with inbuilt o / l & spp, dol starter and dry run protection suitable for motors and as per details given below : incomer:1 no. suitable rated 35 ka, tp, mpcb without inbuilt o / l & with 1no + 1nc auxiliary contacts for total 10 hp of sump pumps ( both pumps working simultaneously ) .incomer metering & pts :415v / v3 / 110v / v3pts, cast resin type, 3 phase for metering & indications, suitable rated 6a, tp mpcb of the fault withstand capacity as of the panel on the primary side of pt & suitable rated 6a, tp mcb on the secondary side of pt. 3 nos. cast resin cts of adequate class, burden & ratio at the incomer metering.r, y, b ( 110v ac ) led lamp & on / off indications ( 110v ac ) led type.digital vaf meter at the incomer ( 110v ) . control transformer & control circuiting for starters / contactors & indication lamps : a ) .1 no. 415v / 55 0 55vcast resin dry type control transformer of adequate va burden to take care of load of all the contactor coils. b ) .suitable rated 6a, dp, mpcb of the fault withstand capacity as of the panel for control circuiting for contactors coils on the primary side of control transformer & suitable rated 6a, dp mcb on the secondary side of control transformer. ( transformer with primary taps at ± 2.5%, ± 5%, 50 hz, centre tap earthed ) . c ) .110v control circuitingd ) .110v control supply healthy indication ( led type ) .e ) .pt of adequate burden can also be used for powering contactor coils of starters and in that case control transformer can be eliminated. bus bars : 100a, tp, aluminium bus bars of required capacity & ka rating with heat shrinkable sleeves.outgoings:sump pump panel ( upto 5.0hp motors ) : 2 sets suitable rated 15 ka, tp, mpcbs with inbuilt o / l relay & inbuilt spp features ( site adjustable ) & with 1no + 1nc auxiliary contacts for 5hp each sump pump motor & each set with the following:a ) .suitable sized 3p contactor with 2no + 2nc auxiliary contacts b ) .on / off / trip led indications ( 110v ) c ) .on / off push buttons d ) .2 pole a / m selector switch for bms application e ) .suitable rated single cast resin ct for metering on y phase, class 1 accuracy & of suitable burden & ratio. f ) . digital ammeter g ) .on / off / trip / a / m potential free contacts for bmsh ) .3 nos. suitable water level controllers with three electrodes ( 110ac ) the sump pump control panel shall be complete with all interconnections, water level controllers & sensors / probes, risers, internal wiring, labels, terminal block etc complete as required. 88 sump pump panel ( for 7.5hp to 10.0hp motor ) : a ) .it shall control two pumps p 1 and p 2. the operation sequence will be as under :b ) .p 1 & p 2 to stop at l 1 c ) .p 1 to start at l 2 d ) .p 2 to start at l 3 ( at l 3 both pump will be running ) audible alarm at l 4 ( 50 mtr range ) .e ) .hooter for annunciation ( solid state buzzer ) f ) .where l 1 < l 2 < l 3 < l 4 ( level of water in the sump ) ( probes / sensors to control operation ) g ) .there shall be selector switch to interchange the starting sequence between p1 & p2. ( selection mode ) important features : sump pump panel shall have following essential features: r, y, b phase indicating lamps with backup. auto / manual selector switch. starter on / off & high level indications, digital ammeters for both pumps. mpcb with inbuilt o / l & spp, dol starter and dry run protection suitable for motors and as per details given below : incomer:1 no. suitable rated 35 ka, tp, mpcb without inbuilt o / l & with 1no + 1nc auxiliary contacts for total 10 hp of sump pumps ( both pumps working simultaneously ) .incomer metering & pts :a ) .415v / v3 / 110v / v3pts, cast resin type, 3 phase for metering & indications, suitable rated 6a, tp mpcb of the fault withstand capacity as of the panel on the primary side of pt & suitable rated 6a, tp mcb on the secondary side of pt. b ) .3 nos. cast resin cts of adequate class, burden & ratio at the incomer metering.c ) .r, y, b ( 110v ac ) led lamp & on / off indications ( 110v ac ) led type.d ) .digital vaf meter at the incomer ( 110v ) . control transformer & control circuiting for starters / contactors & indication lamps : a ) .1 no. 415v / 55 0 55vcast resin dry type control transformer of adequate va burden to take care of load of all the contactor coils. b ) .suitable rated 6a, dp, mpcb of the fault withstand capacity as of the panel for control circuiting for contactors coils on the primary side of control transformer & suitable rated 6a, dp mcb on the secondary side of control transformer. ( transformer with primary taps at ± 2.5%, ± 5%, 50 hz, centre tap earthed ) . c ) .110v control circuitingd ) .110v control supply healthy indication ( led type ) .pt of adequate burden can also be used for powering contactor coils of starters and in that case control transformer can be eliminated. bus bars : 100a, tp, aluminium bus bars of required capacity & ka rating with heat shrinkable sleeves.outgoings:sump pump panel ( for7.5hp to 10.0hp motor ) : 2 sets suitable rated 15 ka, tp, mpcbs with inbuilt o / l relay & inbuilt spp features ( site adjustable ) & with 1no + 1nc auxiliary contacts for 5hp each sump pump motor & each set with the following:a ) .suitable sized 3p contactor with 2no + 2nc auxiliary contacts b ) .on / off / trip led indications ( 110v ) c ) .on / off push buttons d ) .2 pole a / m selector switch for bms application e ) .suitable rated single cast resin ct for metering oneach phase of class 1 accuracy & of suitable burden & ratio. f ) . digital ammeter g ) .on / off / trip / a / m potential free contacts for bmsh ) .3 nos. suitable water level controllers with three electrodes ( 110ac ) the sump pump control panel shall be complete with all interconnections, water level controllers & sensors / probes, risers, internal wiring, labels, terminal block etc complete as required. 89 sewage treatment plant:sewage treatment plant based on mbbr ( moving bed bio reactor ) technology :supply, installation, testing and commissioning of package type pre fabricated sewage treatment plant based on mbbr technology ( moving bed aerobic bio reactor ) of 65 kld capacity including all ms structure, mechanical, electrical and instrumentation works as per technical specification mentioned in the document. the scope shall also include to provide the ss bar screen in grit screen chambers, grease separator, primary & secondary treatment of waste water, air blowers, all necessary interconnecting piping & valves, pumps, dmf and acf filters, chlorinator, ultravoilet dis infection unit, mcc for operation of all motors, all inter connecting power and control wiring, level controllers & other controls, ms puddle flange ( hot dip galvanized after fabrication ) , inlet, outlet, overflow, vent, manhole cover etc, completed in all respect in ready to use and easy to transport condition. ( the entire system tobe installed above ground ) .a ) .nature of effluent domestic sewage from toilets / kitchen.b ) .flow rate 65 kld c ) .sewage incoming characteristics d ) .ph 6.5 8.5 e ) .bod5 upto 250 400 mg / l f ) .s. solid 250 to 450 mg / lg ) .cod 5 upto 600 mg / l h ) .oil & grease 50 mg / l i ) .effluent discharge standard after treatment j ) .ph 6.5 7.5k ) .bod5 less than 10 mg / l l ) .s. solids less than 10 mg / l m ) .cod less than80 mg / l n ) .oil & grease less than 5 mg / l sewage treatment plant shall include the following items:a ) .oil & grease chamber b ) . sewage equalization tank c ) .mbbr tank ( moving bed bio reactor ) d ) .tube settling tanke ) .sludge holding tank f ) .chlorine contact tank g ) .filtration through mgf, acf, chlorinator & uv sterlizerh ) .air blowers, pumps & equipmenti ) .filter pressj ) .piping, valves etc k ) .electrical panel & cablingl ) .all piping, valves & level indicator / controller etc. within plant room. note: a ) .contractor shall ensure submission of detailed civil general arrangement drawings ( plan & section ) , p & i ( programming & instrumentation ) diagram, schematic diagram for the above mention component & additional component such as inserts, puddle flanges, vent pipes etc. if so required for the complete working of the stp and got it approved by the engineer in charge. b ) .only plateform for stp plant shall be in the scope of the owners. the sewerage treatment contractor shall co ordinate, supervise and get all the inserts installed. all supply of ms / insert plates shall be in the scope of the sewerage treatment contractor.supply, installation, testing & commissioning of 2 nos mild steel 5mm frp coatingperforated corrugated bar screen with vertical grating made by 3 mm thick stainless steel plate, spacing of plates 20 mm c / c both sides with suitable lifting arrangement ( size 750 mm wide x 600 mm high approx ) c ) .supply, installation, testing & commissioning of 2 nos mild steel 5mm frp coatingperforated corrugated bar screen with vertical grating made by 3 mm thick stainless steel plate, spacing of plates 20 mm c / c both sides with suitable lifting arrangement ( size 750 mm wide x 600 mm high approx ) d ) .supply, installation, testing and commissioning of the following tanks and chambers in hdpe / pvc as per approved drawings and directions of engineer incharge. the cost shall include all the required mswalking platform, handrail, staircase, manhole cover etc. all above quoted with minimum 10mm m.s tanks with 5mm frp coating protectiona ) .mbbr tank of capacity 25000 litersb ) .tube settler tank of m sc ) .sludge holding tank of capacity 5000 litresd ) .chlorine contact tank of capacity 10000 litrese ) .treated water tank of capacity 15000 litres quoted with minimum 10mm m.s tanks and all above item as per design requirments ( no extra payment shall be paid ) 90 supply, installation, testing & commissioning of horizontal type pumps, having cast iron body, c.i. impeller & shaft connected to tefc motor for 415 volts, 3 phase, 50 cycles a.c. power supply withmechanical / gland seal. protection complete in all respects including suction and delivery headers with upvc pipe of required dia, isolation valves, nrv & pumps shall have following duty: a ) .raw sewage transfer pump ( pumps to be suitable to handle solid handling capacity upto 40 mm size ) set of two pumps ( 1 working + 1 standby ) capacity 2.5 lps ( required 2.5m3 / hr ) head 10 12 mtr.h.p. 2 hp approx. 91 b ) .submersible sewage lifting pumpset of two pumps ( 1 working + 1 standby ) capacity 1.5 lpshead 10 12 mtr.h.p. 2 hp approx. ( solid handling capacity upto 40 mm size ) 92 supply, installation, testing & commissioning of electromagnetic type flow meter at the outlet point of raw sewage transfer pump of 50 mm size suitable for 0 15 klh flow. 93 supply, installation, testing & commissioning of twin type rotary air blower with acoustic encloser, driven through “v” belt or directly coupled through flexible coupling to a tefc motor of suitable hp suitable for 415 ± 10% volts, 3 phase, 50 cycles a / c supply. capable of delivering 70 cum / hr of free air at 0.5 kg / cm2. 94 supply, installation, testing & commissioning of air piping shall comprise of pipes droppers / laterals with ms ( epoxy coated ) header complete with all fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc including cutting holes in wall, makes chases in wall and making good the same. contractor to submit detailed p&i indicating their proposal. 95 supply, installation, testing & commissioning of fine air diffusers capable of delivering 10 12 cum / hr in mbbr tank for providing areation. 96 supply, installation, testing & commissioning of coarse air diffusers capable of delivering 3 6 cum / hr in equalization tank and sludge holding tank for providing areation. 97 supply, installation, testing and commissioning of high surface area @ 400 m2 / m3 at least ring type media to be used for bacterial growth installed in moving bed bio reactor tanks. 98 supply, installation, testing and commissioning of pvc tube deck settling media to be installed in tube settling tank. the media to be supported on msep frame with baffle plate & overflow launder. 99 supply, installation, testing and commissioning of single stage horizontal centrifugal self priming pump with with c.i body, bronze impeller, shaft of stainless steel, shaft sleeve of chrome steel and delivery casing in c.i with mechanical seal, connected to a tefc inductionmotor suitable for 415+ / 10%volts, 3phase50 cycles a.c. supply with 150mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundation, sequence running controller, dry running protection, 80x40 mm i section base plate bolted to cement concrete foundations complete includingisolation valves, nrv & vibration eliminators on both suction & delivery side of pumps .vendor to submit performance curves and technical catalogue of the proposed model for review and information. a ) .sludge feed / transfer pump ( pumps to be suitable to handle solid handling capacity upto 8 10 mm size ) b ) .set of two pumps ( 1 working + 1 standby ) c ) . capacity 1.5 lpsd ) .head 10.0 mtr. e ) .h.p. 1.5 hp approx. 100 supply, installation, testing and commissioning of horizontal centrifugal pumping set with cast iron body, bronze impeller, shaft of ss and c.i. base & head with mechanical seal, connected to a tefc inductionmotor suitable for 415 + / 10%volts, 3 phase 50 cycles a.c supply with 150mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundation, dry running protection, 80x40 mm i section base plate bolted to cement concrete foundations complete including isolation valves, vibration eliminators on both suction & delivery side of pumps and nrv on delivery side of pumps vendor to submit performance curves and technical catalogue of the proposed model for review and information.a ) .filter feed pumpsb.set of two pumps ( 1 working + 1 standby ) c ) .capacity 3.0 lps ( suggested and quoted for 5000lph ) d ) .head 30.0 mtr.e ) .h.p. 3.0 hp approx. 101 supply, installation, testing & commissioning of vertical self supporting filtration unit fabricated from ms sheet as per is: 2825 ( minimum thickness of shell 8 mm and dished ends 10 mm ) pressure gauges, sample cock, gi class c face piping, ci butterfly valves and all accessories, with initial charge of filter media including anthracite, painting inside with epoxy paint and outside with two coat of red oxide primer and two or more coat of synthetic enamel paint, testingand commissioning complete.a ) .mulitgrade pressure sand filtercapacity 5000 lph filtration rate 14000lph / sqm filter dia approx. 800 mm working pressure: 3.0 kg / sqcm. test pressure : 4. 5 kg / sq cm 102 b ) .activated carbon filter filtration rate 14000lph / sqm filter dia approx. 800 mm working pressure: 3.0 kg / sqcm.test pressure : 4. 5 kg / sq cm 103 supply, installation, testing & commissioning of metering pump type chemical doser with 100 lits. pvc / hdpe solution tank, injection fitting assembly, suction and delivery hose upto the point of injection, capacity 0 6 lph, complete in all respects. 104 supply, installation, testing & commissioning of ultravoilet dis infection unit. the unit shall have over 99.9 % bacterial reduction from inlet to outlet. the dis infection chamber shall be constructed of ss 316l on all welted parts. the uv lamp shall be of low pressure mercury vapour type with hard glass enclosure, the sockets shall be water tight & vibration resistant. the lamp life shall be rated for 6000 hours. the unit shall be complete with temperature safety control, lamp out alert circuit & uv radiometer with 4 – 20 ma output. the uv unit shall have with reactor, cabinet housing, cabinet cooling, treatment chamber, electrical panel, temperature safety control, lampout alert, uv radiometer along with uv monitoring system and uv monitoring readout panel.the uv dosage should be > 60, 000 uw – sec / sq.cm. the lamps should be selected based upon the flow requirement of respective unit.flow rate : 5 cum / hr 105 supply, installation, testing & commissioning of all pipings ( as described below ) and isolation control valves including all necessary fittings and clamps, supports, hangers as required i / c cutting and making good the walls wherever required complete in all respects for making the system complete.a ) .gi : submerged air piping ( we suggest upvc. gi is never used for submerged piping ) ms epoxy: air piping & pumped effluent riser ( non submerged ) upvc : interconnecting pipe line after delivery header of pump / filtercontrollers with low voltage relays, stainless steel probes and pvc shroud, control cabling as required length. ( no of probes as required for function of each controller ) . 106 b ) .filter feed pumps to cut off duty pump on low water level in the chlorine contact tank and high water level in the treated water tank and to start pump at low water level in the treated water tank. 107 supply, installation, testing & commissioning of filter press of plate size 18x 18x 12 nos. plate with screw feed pumps of 5 m3 / hr @ 40 m head capacity ( 1 working + 1 standby ) complete in all respects. 108 providing installing testing and commissioning of ultra filteration ( uf ) system for further polishing treated effluent and capable of producing 5, 000 litre / hour. the system shall be complete with uf feed pumps ( 1w+1s ) , backwash pumps ( 1w+1s ) , cartridge filters ( fabricated| ) , uf membranes flushing / cleaning system complete instrumentation for automation and monitoring rotameters pressure gauges interconnecting pipeword electrical cabling and switchgear, all complete electrical installation for stp 109 design, fabrication, assembling, wiring, supply, installation, testing and commissioning of motor control centre fabricated out of 14 gauge crca sheet steel. cable gland plates shall be provided on top as well as at the bottom of the panels. panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of red oxide primer and final approved shade of powder coated paint. 2 nos. earthing terminals shall be provided for 3 phase, 4 wire, 50 hz supply system. lifting hooks shall also be provided in case of large panels. approval shall be taken for each panel before fabrication. quoted rates shall be inclusive of cables ( in accordance to specification ) with earthing from panel to each motor / equipment.motor control centreincoming: a ) .200 amps tpn mccb with the following accessories:b ) .0 500 volts 96 x 96 mm square electronic voltmeter with selector switch shall be protected by 2 amps tp mcb. 1 set.c ) .0 100 volts 96 x 96 mm square electronic voltmeter with selector switch and shall be 100. / 5 amps 10 va cl: cts. 1 set. d ) .pharse indicating lamps shall be protected by 2 amp sp mcb 3 sets. bus bar:a ) .200 amps tpn ( 15 ka ) copper bus bar with heat shrinkable insulation sleeves.outgoing; a ) .10 nos. of 25 amp capacity tpn mcb with 10 nos. dol starters and out going feeders to all the pumps etc. ( including standbies ) . each compartment shall contain auto / manual selector switch andindicating lamp with mcb’s for ‘on / off / trip’ status of motor b ) .spare 25 amps tpnmcbs2 nos. c ) .spare 32 amps tpnmcbs2 nos. d ) .necessary cable alleys, internal / cabling, wiring, cabling from mcc to various pumps / equipment and interlocking, earthing for all equipment shall also included mcc for all stp equipments / pumps as described above.notes : a ) .all mccbs / mcbs shall be of 15 ka breaking capacity and suitable for motor duty application.b ) .all motor starters shall be provided with automatic level controller. c ) .dol starters shall be used for motors below 10hp and star delta starters for other motors . motor control centre incoming 200 amps tpn mccb with the following accessories:0 500 volts 96 x 96 mm square electronic voltmeter with selector switch shall be protected by 2 amps tp mcb. 1 set.0 100 volts 96 x 96 mm square electronic voltmeter with selector switch and shall be 100. / 5 amps 10 va cl: cts. 1 set.phase indicating lamps shall be protected by 2 amp sp mcb 3 sets.bus bar 200 amps tpn ( 15 ka ) copper bus bar with heat shrinkable insulation sleeves.outgoing10 nos. of 25 amp capacity tpn mcb with 10 nos. dol starters and out going feeders to all the pumps etc. ( including standbies ) . each compartment shall contain auto / manual selector switch andindicating lamp with mcb’s for‘on / off / trip’ status of motorspare 25 amps tpnmcbs2 nos. spare 32 amps tpnmcbs2 nos. necessary cable alleys, internal / cabling, wiring, cabling from mcc to various pumps / equipment and interlocking, earthing for all equipment shall also included notes : all mccbs / mcbs shall be of 15 ka breaking capacity and suitable for motor duty application.all motor starters shall be provided with automatic level controller.dol starters shall be used for motors below 10hp and star delta starters for other motors .provision shall be made for providing potential free contacts to all pumps starters.mcc for all stp equipments / pumps as described above. sub total of part a 110 part b ( o & m cost ) ( for 5 years ( 60 months ) from final handing over of all works. ) ( optional ) trained operator to operate the stp round the clockincluding operator and regular visit of supervisor. perannum including all charges like amc , monthly charges of water analysis and all consumables etc included. sub total of part b ( rate only ) 111 part:c providing & laying upvc pressure pipes of 6 kg / sq.cm pressure rating class 3 ( is : 4985 2000 ) including fittings, tees, bends, clamps, coupling and adaptors supports, and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of surplus earth with a lead up to 100m complete, compaction and consolidation including sand bedding all around upvc pipe & fittings and thrust blocks at bends as per standard design.200od 112 constructing rccchamber of holding capacity 10 m3 with grade of m25 including cost of centering , shuttering & pcc below foundation in 1: 5:10 & 75 mm thick and inside chamber of 75mm thick as per standard design including inside plastering with cement mortar 1:6 ( 1 cement :6 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design .rate to include cost of reinforcement , excavation and filling of earth. earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) , including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. the contractor has to detect different unilities like sewer line , water supply line , electrical cable , telephone cable , gas pipe line etc. using utility detecting machine before start of excavation and shall start excavation only after getting permission of engineer in charge.all kinds of soil.depth upto 1.5m from existing ground level 113 b ) filling available excavated earth ( excluding rock ) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 114 providing & laying cement concrete all works upto plinth level : c ) 1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) : 8 graded stone aggregate 40 mm nominal size ) 115 providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer in charge. ( note : cement content considered in this item is @ 330 kg / cum. excess / less cement used as per design mix is payable / recoverable separately ) . a ) uptoplinth 116 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.b ) thermo mechanically treated bars of grade fe 500d or more 117 centering and shuttering including strutting, propping etc. and removal of form for : c ) foundations, footings, bases of columns, etc. for mass concrete 118 d ) suspended floors, roofs, landings, balconies and access platform 119 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 10 in foundation and plinth in: a ) cement mortar 1:6 ( 1 cement : 6 coarse sand ) for 230mm thick brick work 120 b ) 12 mm cement plaster of mix :1:4 ( 1 cement: 4 fine sand ) 121 c ) 15 mm cement plaster on rough side of single orbrick wall of mix:1:4 ( 1 cement: 4 fine sand ) 122 d ) 6 mm cement plaster of mix :1:3 ( 1 cement : 3 fine sand ) 123 designing, preparation of shop drawings, supplying, erection, testing, commissioning of all mechanical, electrical and other components including getting approval of successful test results from approved / authorized agency from pollution & environmental authorities, operating & maintaining upto successful commissioning, for 5 m3 / day capacity sewage treatment plant sewage treatment plant near workshop area ( complete system to be compact type, skid mounted / cabinet enclosed, as per detailed shop drawings to be approved ) suprime / sintex maketotal c / f to summary 124 r.o water treatmentplant: supply, installation, testing and commissioning of r.o. plant capacity of 750 lph ( complete system to be compact type, skid mounted / cabinet enclosed, as per detailed shop drawings to be approved ) for the following parameters and consisting of ( but not limited to ) the following main components: ( i ) inlet quantity : as per detailing ( ii ) output quantity : 750 lph ( iii ) inlet tds : 600 ppm ( iv ) outlet tds : 75 ppm ( v ) inlet hardness : 350 ppm ) ( vi ) outlet hardness : 50 ppm ) raw water pumps of horizontal, centrifugal type suitable for a flow rate of 1500 lph at 25m head. the pump construction shall be of ss 304 & impeller shall be also ss 304. the motor shall be tefc suitable for a supply of 415v / 3 phase / 50hz supply. the pump shall be supplied complete with base channel coupling foundations, bolts, pressure gauge at inlet and outlet of each pump. 2 nos. ( 1w+1s ) special antiscalant dosing system consisting of one hdpe tank of 100 litre capacity with a positive displacement diaphragm dosing pump having variable flowrate of 0 6 lph. the motor shall be suitable for operation at 240v / single phase / 50hz supply. the pump shall be supplied complete with necessary polypropylene piping, valves, strainers & injection fittings. 1 set micron cartridge filter suitable for a flowrate of 1500 lph to achieve particle filtration of less than 5 microns. the unit shall be supplied complete with inlet and outlet branches removal cap for replacement of element, inlet and outlet pressure indicators. ( one for the pressure treatment & other for cip system ) moc: polypropylene 2 sets r.o high pressure feed pumps of vertical, multistage centrifugal type suitable for a flowrate of2000 lph at 14 kg / sq.cm. the pump construction shall be of ss 316 l & impeller shall be also ss 316 l. the motor shall be of tefc suitable for a supply of 415v / 3 phase / 50 hz supply. the pump shall be supplied complete with base channel coupling foundation, bolt, pressure gauge at inlet and outlet of each pump. 2 nos.r.o. modules made out of spiral wound thin film composite suitable to withstand pressure of 20kg / sq.cm. suitable bspt / npt connections shall be used for connecting feed & reject ends. the modules shall be supplied complete with all necessary instrumentation, valves for sampling, drain, reject & permeate, epoxy coated structural steel bases and supports, as per following system capacity requirements: ( i ) total net treated water output of system = 750 lph ( ii ) system recovery= 50 60 % ( iii ) filtration area per membrane = 85 sq.ft. ( iv ) number of membranes = the total number of membranes required shall beas per requirements, supported by calculations from the vendor. centralised plc control panelalong with touch screen digitial display board along with all digital sensors for tds & flow, made out of crca sheet min. 2mm thick having main contactors for all pumps ( listed above ) including spp, 3 phase thermal overload relay. the control panel for monitoring and control of p.o. system shall include all required signal lamps, hrc fuses, annunciation box with hooter. all control and power cabling along with double earthing between the panel shall be included in the scope of supply of the contractor. an emergency stop push button shall be provided in the panel. the mcc panel shall have the following interlocks: i ) high pressure pump unit trip in case of low suction pressure. ii ) high pressure pump unit trip in case of high discharge pressure.iii ) special anti scalant dosing pump trips in case high pressure pump trips and vice versa.iv ) high pressure pump trip in case of high conductivity in permeate.v ) shc dosing pump trips incase high pressure pump trips and vice versa. vi ) orp with dump valve. 1 seti ) first fill of all chemicals and lubricants to commission and operate the plants. 1lotj ) all interconnecting piping work with valves: i ) low pressure side till r.o. feed water pump. piping shall be of extra strong pvc and all valves shall be of extra strong pvc and all valves shall be pvc ball valves. 1 lotii ) high pressure side piping from the r.o. high pressure pumps to the reject stream control valves shall be of ss 304 using all ss fittings ball valves of suitable pressure rating shall be used till 25 mm size, above 25 mm, flanged globe / wafer butterfly valves in ss construction shall be used. rejects pressure control valves shall be globe valve and feed flow control valve shall be of ss 304. lotiii ) before procurement of material contractor should be get technical approval from consultants. ( all for above from a to j complete ) 125 r.o water storage complete 316 stainless steel treated water storage tank ( double wall ) of capacity 2000 litres including all inlet / outlet connections, accessories, valves, double seal manhole covers, insulation etc.the stainless steel tank must be ozone resistant and to be used as ozone contact tank. fabrication to be done as per approved shop drawing. ( make :nector ) 126 providing and placing on terrace ( at all floor levels ) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank.. 127 activated carbon filter ( automatic type for online installation before the micron filters ) suitable for a flow rate of 1500 lph. the material of construction shall be composite frp. the unit shall be supplied complete with multi port valves, inlet and outlet branches removal caps of replacement of elements inlet and outlet pressure indicators. 1 set 128 hydropneumatic system for r.o supply providing fixing and commissioning suitable complete composite hydropneumatic system consisting ofhorizontal / vertical multistage centrifugal pump having stainless steel impellers, stainlesssteel shaft, stainless housing and single mechanical seal and pressurised tankof required specifications and of non toxic rubber diaphragm, complete with all accessories including pressure switch, pressure gauge and electrical panel with all necessary protection and operational devices i.e alternate pumping operation and shut off during dry running conditions etc., and inclusive of ss 316 suction and delivery manifold of required size with non return valve and ball valveand withsuitableelectrical motor to be operated on 210 / 220 or 400 / 440 volt 50 cycle suitable for following duty and with total no. of pumps 2 nos. ( 1 working+ 1 standby ) complete with the approval of engineer in charge. before procurement of material contractor should be get technical approval from consultants.a ) discharge:150 lpmb ) head:45 m c ) app. capacity of thevessel ( frp ) : as requiredtotal c / o to summary 129 hot waterboilers and other related accessories electrical hot water generators system with solar back up.hot water mixing storage tank ( 2 sets for club and benquet hall ) supply, installation, testing and commissioningof solarwater heating system capable of generating 7500lpd of hot water per day at 60 oc along withinsulated horizontalhot watermixing tank capacityand design code i.s: 2825 fabricatedof 6 mm thick s.s. 304plateand 10 mmthickdishedend and nozzles complete with inlet, cold waterinlet / outlet chain connection withflanges, manhole with bolted cover with 72 kw electrical back up along with control panels . tankshall beinsulated with 50 mm thickresin bondedfibre glass ( density 24 kg / cum ) and covered with500gpolythene sheetand 24 gauge aluminumsheet cladding giving proper overlaps and sealing the joints with suitable adhesive compound, including the following additional accessories / specifications:working pressure : 7.5 kg / cm²i ) safety valveii ) dial type thermometer iii ) thermowell for thermostat elements cold water inlet valve 80 mm dia check valve in cold water inlet 80 mm dia.hot water inlet / outletsecondary side 50 mm dia valve plate type heat exchanger compleate with pumps required specification.hot water outlet connection valve to system 100mm diaplate type heat exchanger compleate with pumps required specification.hot water outlet connection valve to system 100mm dia hot water return inlet 65 mm dia drain valve 50 mm diaair release valve 25mm diahot water return nrv 65 mm dia solar pre heating working inlet 80 mm dia butterfly valvesolar pre heating working inlet 80 mm dia nrv electrical control panel as per approved apecification temp. controller 130 hot water returnpumps for domestic waterprovidingand fixing horizontal multistage centrifugal pumping set with stainless steel ss 304 stage casing and ss 304 impellers with stainless steel ss 304 shaft as per iec standards andss 304 suction & discharge casing, connected to tefc ventilated induction motor of 2 pole, 2900 rpm, suitable for 400 / 440 v phase, 50 hz a.c. supply with pressure gauge and with gunmetal isolation cocks, vibrationelimination pads etc. complete with base and frame, nuts & bolts and necessary rcc foundations as per requirement as per instructions and pump shall follow following dutynos : 2 ( 1 w +1 s ) capacity: app.100 lpm head :15 m 131 solar hot water re curculation pumps : providingand fixing horizontal multistage centrifugal pumping set with stainless steel ss 304 stage casing and ss 304 impellers with stainless steel ss 304 shaft as per iec standards andss 304 suction & discharge casing, connected to tefc ventilated induction motor of 2 pole, 2900 rpm, suitable for 400 / 440 v phase, 50 hz a.c. supply with pressure gauge and with gunmetal isolation cocks, vibrationelimination pads etc. complete with base and frame, nuts & bolts and necessary rcc foundations as per requirement as per instructions and pump shall follow following duty nos : 2 ( 1 w +1 s ) capacity: app100 lpm head :55 m 132 electrical panel providing motor control centres fabricated from 16 gauges m.s. sheet with powder coated finish. the control panels should be comparable with h.p. of the motor as specified.for hot water , steam genration systemshot water recuculation pumps, hot water supply pumps condensate pumps etc.a ) one incoming main isolation mccb of required rating.b ) fully taped aluminum bus bar ofrequiredcapacity in a separate bus bar chamber.c ) isolation switch units with mccbof required rating, for each unit.d ) fully automatic dol starter with pushbutton and on / off indicating lights for each unit, for following requirements:i ) hot water boilers 2 nos. of required 74 kw eachii ) hot water re circulation pumps 2 nos. ( 1 working+ 1 stand by ) of required hp iii ) solar hot water recirculation pumps 2 nos. ( 1 working+ 1 stand by ) of required hpiv ) one no. spare feeder required 5 hprotary switches for auto / manual on / off operations for each unit.rotary duty selector switches.panel type voltmeter 150mm with rotary selector switch for reading voltage between phases.neon phases indicating lights on the incoming mains. single phasepreventorfor each motor. ct operated relayall internal wiring colour coded from incoming mains to various switchgear, starter, meter, indicating lamp and bus bar. all the cable entry to the panel shall be from the top. ( all for above from item ( a ) to ( l ) complete set ) . ( the shop drawing to be preparedand approved before fabrication ) total c / o to summary 133 swimming pool filteration system recirculation pumps main pool + jacuzziarea : 550 m2 x 1.2 m balancing tank : 60 m3total pool volume : 660 m3 + 60 m3 = 720 m3filtration flow rate : 180m3 / hr filtration plant with pumpsupply, instalation, testing & commissioning of bobbin wound side mount sand filter manufactured with fiber glass and polyester resin, uv resistance surface, fitted with collector arms and diffuser made from unplasticised pvc and polypropylenewith lid in polyester resin and fibre glass, manual air purgeand 4 pvc flanged connection for inlet and outlet, pressure gauge, water drain / empty drain for filter etc.complete in all respects. including corse & fine silica sand media for filterapx. 7200kgcapacity 60000 ltrs / hrdesign @30000 ltrs / sqm / hr.diameter1600 mm working pressure4.0 kg / cm² 134 valve battery valve battery manifold made in pvc with flanges for connecting to filters consists of set of 5 buttterfly valves for carrying out filtration, back washing, rinsing and shut down of the filters. size : 4 inchsupply, instalation, testing & commissioning of self primingpumps with ci body, in built ci strainer basket, impeller in ci / bronge, motor shaft in stainless steel aisi 420, mechanical seal in sic sic / carbon ceramic, motor housing in aluminium, withmotor 2850rpm, f class insulation, protection ip 55. ( 3w+1s ) 135 supply, instalation, testing & commissioning of self primingpumps with ci body, in built ci strainer basket, impeller in ci / bronge, motor shaft in stainless steel aisi 420, mechanical seal in sic sic / carbon ceramic, motor housing in aluminium, withmotor 2850rpm, f class insulation, protection ip 55. ( 3w+1s ) capacity60000 ltrs / hrhead 16 mtrhp 7.5, three phase 136 swimming pool u.v. sterlizersupply, instalation, testing & commissioning of u.v. sterlizer with s.s. housing outside, u.v. lamp, glass tube and all other accessories with cleaning arrangement, supports, inlet outlet connection with bypass arrangement including s.s. cabinet with glass door of suitable size to house the u.v. sterlizer complete with required accessories. flow rate = 60000 ltr / hrworking pressure = 4.0 kg / sqm uv lamp wattage = 400 w 137 dosing pumpsupply, instalation, testing & commissioning of chemical dosing pumpfor chlorination with 200 ltrs. sintex tank and accessories capacity0 20 litres / hr.head35 m 138 stainless steel drain supply, instalation, testing & commissioning ofstainless steel drain grating plate made out of 316 quality s s plates with suitable supporting frame and of following sizes and having holes of required size for drainout chamber.size 400x400 mm 139 inlet nozzlesupply, instalation, testing & commissioning of flow adjastable abs inlet nozzles uv treated with s.s. screws to fit in the 2 pvc pipes 140 suction inlets ( vacuum points ) supply, instalation, testing & commissioning of abs white plastic suction port / vacuum nozzle with 2 inch solvent cement connection 141 supply, instalation, testing & commissioning of stainless laddersteel 316 ladders, width: 500mm wide, handrails dia 43mm stainless steel, non slip stepsprovided with anchoring socket.a ) 3 step standard ladder with anti skid steps 142 b ) 4 step standard ladder with anti skid steps 143 underwater led lights supply, instalation, testing & commissioning of 12volt 54 w under water stainless steel 316l led light fixture ( ip 68 ) including all required assessories & making connection as required. with 2 mtr power cord. 144 power supply supply, instalation, testing & commissioning oftransformer for led lights 12v dc, 30 amp 145 deck box supply, instalation, testing & commissioning of abs white plastic deck. 146 cleaning accessories a ) extensivetelescopic handle, ( 2.4 4.8 ) metres long &1.1mm thick for cleaning attachment in anodized almunium. 147 b ) transparent blue polyethylene hose 40mm ( 1 1 / 2 ) dia 30 m length. 148 c ) surface net skimmer made in polypropylne 149 d ) deep bag net skimmer made in polypropylne 150 e ) curved polybristle wall brush 450 mm 151 f ) test kit for ph and chlorine. 152 g ) hi grade stainless steel algae brush 10 153 h ) vacuum head with ss body, 1 1 / 2 connection size 900 mm long 154 i ) deluxe large vacuum head with 4 wheels, alu body, plastic handle, 1 1 / 2 connection size 445x130 mm 155 j ) polybristle wall brush 10 ( 26cm ) 156 k ) chemical tcca 90 ( 50 kg. ) & alum ( 30 kg. ) 157 l ) nylon rope 158 upvc pipesproviding and fixing upvc pressure pipes ( 10kg / cm2 ) with plain socket suitable for solvent cement jointing conforming to is:4985 / 2000 & fittings conforming to is 7834 / 87.cut to required lengths including all necessary fittings and specials such as bends, tees, unions, reducers, flanges and plugs etc. the pipes & fittings shall be tested to a pressure of 10 kg / sq.cm.a ) 32 mm dia 159 b ) 50 mm dia 160 c ) 63 mm dia 161 d ) 75 mm dia 162 e ) 90 mm dia 163 f ) 110 mm dia 164 g ) 160 mm dia 165 h ) 200 mm dia 166 i ) 250 mm dia 167 ball valveproviding and fixing pvc lever operated ball valve of full flow with setting and gland of superior quality having minimum working pressure of 10 kg / cm2 with union, flanges where as required.a ) 32mm dia 168 40mm dia ( rate only ) 169 50mm dia ( rate only ) 170 63mm dia 171 75mm dia ( rate only ) 172 90mm dia ( rate only ) 173 butterfly valve providing and fixing upvc butterfly valves. tested to a pressure not less than10 kg / sq.cm. including rubber gasket, flanges, nuts, bolts, washers complete as required. a ) 90 mm dia 174 b ) 110 mm dia 175 c ) 160 mm dia 176 d ) 200 mm dia 177 e ) 250 mm dia 178 non return valveproviding and fixing pvc ball type or spring loaded non return valve with setting and gland of superior quality having minimum working pressure of 10 kg / cm2 with union, flanges where as required.a ) 50mm dia 179 b ) 63mm dia 180 c ) 75mm dia 181 providing and fixing of upvc wafer check valve non return valves ( pn 10 ) complete with matching flanges, rubber insertion, nuts, bolts and washer etc. of following sizes.a ) 75mm dia 182 b ) 90 mm dia 183 c ) 110 mm dia 184 d ) 160 mm dia 185 e ) 200 mm dia 186 f ) 250 mm dia 187 puddles sleevesupply & fixing of following sizes of heavy duty pvc puddle flanges ( upvc pipe ( 10 kg / cm2 ) fixed with flanges, length 400 to 600 mm length ) on the wall of plantroom, balancing tank and the water body walls & slab ( as required ) . to be laid in between the steel reinforcement before rcc. does not include any civil work. a ) 32 mm dia 188 c ) 50 mm dia 189 d ) 63 mm dia 190 e ) 75 mm dia 191 f ) 90 mm dia 192 g ) 110 mm dia 193 h ) 160 mm dia 194 i ) 200 mm dia 195 j ) 250 mm dia 196 supply, laying, testing and commissioning of ss 304 grade 300mm dia pump suction header with 2 nos 200mm dia flange connection for balancing tank to pump suction header, 1 no. 90 mm dia flange connection for vacuum pipe & 1 no. 200 mm dia flange connection for pool drain pipe & 4no. 200mm dia & 2 no. 160mm diaflange connection for pump suction. 197 supply, laying, testing and commissioning of ss 304 grade 200mm dia pump delivery header with 1 nos 200mm dia flange connection for filter inlet header, 1 no. 160 mm dia flange connection for drain pipe & 4 no. 160mm dia flange connection for pump delivery. 198 supply, laying, testing and commissioning of following size pvc insulated sheathed copperconductor 1100 v grade unarmoured cable with required size of sleeves complete as required. a ) 4 x 16 sq.mm 199 c ) 4 x 6 sq.mm ( rate only ) 200 d ) 4 x 4 sq.mm ( rate only ) 201 e ) 4 x 2.5 sq.mm 202 f ) 4 x 1.5 sq.mm ( rate only ) 203 g ) 3 x 6 sq.mm ( rate only ) 204 h ) 3 x 4 sq.mm 205 i ) 3 x 2.5 sq.mm ( rate only ) 206 j ) 3 x 1.5 sq.mm ( rate only ) 207 k ) 2 x 6 sq.mm 208 l ) 2 x 4 sq.mm ( rate only ) 209 m ) 2 x 2.5 sq.mm 210 n ) 2 x 1.5 sq.mm 211 providing and fixing 6 swg dia g.i. wire on surface or in 6 gauge gi wire recess for loop earthing as required. 212 supplying and installing following size of perforated painted with powder coating m.s. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as required. a ) 300 mm width x 50 mm depth x 1.6 mm thickness 213 b ) 150 mm width x 50 mm depth x 1.6 mm thickness 214 providing & fixing m.s. structural work fabricated from standard section e.g. m.s rounds, angles, channels, plates including cutting to size, drilling, welding fixing and welding to insert plates in rcc structural members as directed by engineer in charge including cutting and making good the walls, ceilings and floors ( for pipe supports, clamps etc. ) 215 electrical control panel supply, installation, testing and commissioning of following swimming pool panel 415 v, 1 / 3 phase and 50 hz power distribution system. thepanel shall be free standing floor mounting sheet metal enclosed dust and vermin proof confirming to ip 54, compartmentalized design fabricated out of 16 swg sheet steel, painting earthing numbering, danger plate as per specifications and drawings. flush front with aluminium busbars, seperate earth bus bars to be provided throughout the length of the panel the incoming and outgoing feeder breakers, fuses, indicating lamps etc shall be accomadated in a modular multilier arrangement. the panel shall be powder coated through 9 tank process. adequate size cable alley shall be provided forcable termination.the outgoing feeders inside shall be connected through bus bars / flexible cable links. incoming: one ( 1 ) no. 200a tp 25 ka mccb with thermomagnetic digital flush mounted 0 200a ammeter with 3 way and off selection switch with 3 nos. 200 / 5 amp ct. 1 set ( 3 nos. ) of phase indication lamps 200a 25 ka tpn aluminium bus bar. it shall be insulated with heat shrinkable sleeves and shall be color coded. outgoing: recirculation pumpsix ( 6 ) nos. star delta starter complete with separate single phasing protection feature. on / off indicating lamps, relay, contractors, start / stop push button, auto / manual selector switch, sufficient nos of potential free spare contacts, etc for suitable hp3 nos. 6amp dp mcb of suitable rating with correct thermal range suitable for chemical dosing3 nos. toggle switch for doser3 nos. 6amp dp mcb of suitable rating with correct thermal range suitable for uv 3 nos. toggle switch for uv 1 nos.16amp dp mcb of suitable rating with correct thermal range suitable for underwater lights 1 nos. toggle switch for led pool lightstotal c / o to summary 216 entry water bodypressure sand filtersupply, instalation, testing & commissioning of bobbin wound top mount sand filter manufactured with fiber glass and polyester resin, uv resistance surface, non corrosive material, complete with 6 way 2 multiport valve with filter connection / inter connecting piping, pressure gauge, water drain / empty drain for filter.including corse & fine sand media for filter as per approved calculation capacity15000 ltrs / hr design @35000ltrs / sqm / hr. diameter750 mm 217 filter re circulation pumpsupply, instalation, testing & commissioning of self primingpumps with plastic body, in built strainer basket, impeller in ppo, motor shaft in stainless steel aisi 420, mechanical seal in sic / graphite and steatite, motor housing in aluminium, withmotor 2800rpm, f class insulation, protection ip 55. ( 1w+1s ) capacity15000 ltrs / hr head 12 mtrhp 2.0, three phase 218 fountain re circulation pump single stage high speed horizontal centrifugal monobloc with volute type delivery casing pool recirculation submersible pump, delivery casing & motor body in ci, motorshafts in carbon steel, impeller in ci withmotor hp7.5, three phase 219 single stage high speed horizontal centrifugal monobloc with volute type delivery casing pool recirculation submersible pump, delivery casing & motor body in ci, motorshafts in carbon steel, impeller in ci withmotor hp2.0, single phase 220 swimming pool u.v. sterlizer supply, instalation, testing & commissioning of u.v. sterlizer with s.s. housing outside, u.v. lamp, glass tube and all other accessories with cleaning arrangement, supports, inlet outlet connection with bypass arrangement including s.s. cabinet with glass door of suitable size to house the u.v. sterlizer complete with required accessories. flow rate = 20000 ltr / hrworking pressure = 2.5 kg / sqmuv lamp wattage = 40 w 221 chlorine tablet feedersupply, instalation, testing & commissioning of chlorine tablet feeder with accessories capacity = 4.5 kg 222 stainless steel drain supply, instalation, testing & commissioning ofstainless steel drain grating plate made out of 316 quality s s plates with suitable supporting frame and of following sizes and having holes of required size for drainout chamber.size 200x200 mm 223 fountain nozzlesupply, instalation, testing & commissioning of brass crome plated gyserjet nozzle with 1 connection with required accessories. 224 suction inlets ( vacuum points ) supply, instalation, testing & commissioning of abs white plastic suction port / vacuum nozzle with 2 inch solvent cement connection 225 supply of12volt 12w under water stainless steel 316 ring underwater led lightstype led warm white light ( ip 68 ) including all required assessories & making connection as required. with 2 mtr power cord.for fountain nozzle 226 power supplysupply, instalation, testing & commissioning oftransformer for led lights 12v dc, 30 amp 227 supply, instalation, testing & commissioning ofrgb programmer for led lights. 228 deck boxsupply, instalation, testing & commissioning of abs white plastic deck. 229 upvc pipes providing and fixing upvc pressure pipes ( 10kg / cm2 ) with plain socket suitable for solvent cement jointing conforming to is:4985 / 2000 & fittings conforming to is 7834 / 87.cut to required lengths including all necessary fittings and specials such as bends, tees, unions, reducers, flanges and plugs etc. the pipes & fittings shall be tested to a pressure of 10 kg / sq.cm.a ) 32 mm dia 230 50 mm dia 231 63 mm dia 232 75 mm dia 233 90 mm dia 234 110 mm dia 235 160 mm dia ( rate only ) 236 200 mm dia ( rate only ) 237 ball valve providing and fixing pvc lever operated ball valve of full flow with setting and gland of superior quality having minimum ball working pressure of 10 kg / cm2 with union, flanges where as required.a ) 32mm dia ( rate only ) 238 40mm dia ( rate only ) 239 50mm dia 240 63mm dia 241 75mm dia 242 90mm dia ( rate only ) 243 butterfly valveproviding and fixing upvc butterfly valves. tested to a pressure not less than10 kg / sq.cm. including rubber gasket, flanges, nuts, bolts, washers complete as required.a ) 90 mm dia ( rate only ) 244 110mm dia 245 160 mm dia ( rate only ) 246 200 mm dia ( rate only ) 247 non return valve providing and fixing pvc ball type or spring loaded non return valve with setting and gland of superior quality having minimum working pressure of 10 kg / cm2 with union, flanges where as required. 50mm dia ( rate only ) 248 63mm dia 249 75mm dia 250 providing and fixing of upvc wafer check valve non return valves ( pn 10 ) complete with matching flanges, rubber insertion, nuts, bolts and washer etc. of following sizes. a ) 75mm dia ( rate only ) 251 90 mm dia 252 110 mm dia 253 puddles sleeve supply & fixing of following sizes of heavy duty pvc puddle flanges ( upvc pipe ( 10 kg / cm2 ) fixed with flanges, length 400 to 600 mm length ) on the wall of plantroom, balancing tank and the water body walls & slab ( as required ) . to be laid in between the steel reinforcement before rcc. does not include any civil work. a ) 32 mm dia ( rate only ) 254 50mm dia ( rate only ) 255 supply, laying, testing and commissioning of ss 304 grade 200mm dia pump delivery header with 1 nos 200mm dia flange connection for filter inlet header, 1 no. 160 mm dia flange connection for drain pipe & 4 no. 160mm dia flange connection for pump delivery. 256 supply, laying, testing and commissioning of following size pvc insulated sheathed copperconductor 1100 v grade unarmoured cable with required size of sleeves complete as required. a ) 4 x 16 sq.mm 257 4 x 2.5 sq.mm 258 3 x 4 sq.mm 259 2 x 6 sq.mm 260 2 x 4 sq.mm ( rate only ) 261 2 x 1.5 sq.mm 262 providing & fixing m.s. structural work fabricated from standard section e.g. m.s rounds, angles, channels, plates including cutting to size, drilling, welding fixing and welding to insert plates in rcc structural members as directed by engineer in charge including cutting and making good the walls, ceilings and floors ( for pipe supports, clamps etc. ) 263 electrical control panelsupply, installation, testing and commissioning of 415 v, 1 / 3 phase and 50 hz motor. the switchboard cubical indoor type made of 16 swg crca sheet painted with powder coated paint of siemens grey shade. the cubical is wall mounted with dust & vermin proof construction with inter connection. it comprise with the following:a ) one incoming mains of 63 amps. mccb – tp, schneider b ) one no. 0 – 600 v digital voltmeter, mecon make 96 sq.mm with voltage selector switch. make. c ) three phase led type indicating lights for incoming mains. d ) one no. ct operated 0 – 60 / 5 a digital ammeter, mecon e ) two no. star delta starter schneider make with on / off push button and on / off indication light f ) two no. star delta starter schneider make with on / off push button and on / off indication light g ) four no. auto / manual selector switches, salzer make h ) one no. mcb dp 6 amps. for u / v system, schneider make. i ) one no. toggle switch for u / v system, hsd make. j ) one no. mcb sp 6 amps. for smps dc power supply for led light, schneider make. k ) one no. toggle switch for led pool lights, hsd make.total c / o to summary 264 pond aerationsupply, instalation, testing & commissioning of surface aerating fountain with pump, float, spray / fountain nozzle, conrtol, lights and cable, pump capacity 1 3 hp the aerator shall be a floating 265 supply, instalation, testing & commissioning of surface aerating fountain with pump, float, spray / fountain nozzle, conrtol, lights and cable, pump capacity 5 7.5 hp the aerator shall be a floating 266 supply, instalation, testing & commissioning of surface aerating fountain with pump, float, spray / fountain nozzle, conrtol, lights and cable, pump capacity 10 hp the aerator shall be a floating 267 supply, instalation, testing & commissioning of surface aerating fountain with pump, float, spray / fountain nozzle, conrtol, lights ss frame and cable, pump capacity 10 hp the aerator shall be a floating 268 miscellaneous item ( hanging wire etc ) total c / o to summary 269 golf course water bodies / ponds stpwater supply:making connection of g.i. distribution branch with g.i. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : a ) 25 to 40 mm nominal bore 270 b ) 50 to 80 mm nominal bore 271 fixing water meter and stop cock in g.i. pipe line including cutting and threading the pipe and making long screws etc. complete ( cost of water meter and stop cock to be paid separately ) . 272 brass fittings providing and fixing gun metal gate valve with c.i. wheel of approved quality ( screwed end ) :a ) 25 mm nominal bore 273 b ) 20 mm nominal bore 274 c ) 32 mm nominal bore. 275 d ) 40 mm nominal bore 276 e ) 50 mm nominal bore 277 f ) 65 mm nominal bore 278 g ) 80 mm nominal bore 279 providing and fixing ball valve ( brass ) of approved quality, high or low pressure, with plastic floats complete : a ) 15 mm nominal bore 280 b ) 20 mm nominal bore 281 c ) 25 mm nominal bore 282 providing and fixing gun metal non return valve of approved quality ( screwed end ) :a ) 25 mm nominal bore horizontal 283 vertical 284 b ) 32 mm nominal borehorizontal 285 vertical 286 c ) 40 mm nominal bore horizontal 287 vertical 288 d ) 50 mm nominal bore horizontal 289 vertical 290 e ) 65 mm nominal bore horizontal 291 vertical 292 f ) 80 mm nominal borehorizontal 293 vertical 294 providing and fixing brass ferrule with c.i. mouth cover including boring and tapping the main :providing and fixing brass ferrule with c.i. mouth cover including boring and tapping the main :15 mm nominal bore 295 providing and fixing brass ferrule with c.i. mouth cover including boring and tapping the main :providing and fixing brass ferrule with c.i. mouth cover including boring and tapping the main :15 mm nominal bore 296 25 mm nominal bore 297 c.i. / ductile iron pipes & specialsproviding and laying s&s c.i. standard specials such as tees, bends, collars, tapers, caps etc. ( heavy class ) : a ) up to 300 mm dia 298 b ) over 300 mm dia 299 providing and laying flanged c.i. standard specials such as tees, bends, collars, tapers, caps etc., suitable for flanged jointing as per is : 1538 :a ) up to 300 mm dia 300 b ) over 300 mm dia 301 providing and laying s&s centrifugally cast ( spun ) iron pipes ( class la ) conforming to is 1536 :a ) 100 mm dia pipe 302 b ) 125 mm dia pipe 303 c ) 150 mm dia pipe 304 d ) 200 mm dia pipe 305 e ) 250 mm dia pipe 306 providing lead caulked joints to spun iron or c.i. pipes and specials, including testing of joints but excluding the cost of pig lead : a ) 100 mm diameter pipe 307 b ) 125 mm diameter pipe 308 c ) 150 mm diameter pipe 309 d ) 200 mm diameter pipe 310 e ) 250 mm diameter pipe 311 providing flanged joints to double flanged c.i. / d.i. pipes and specials, including testing of joints : a ) 100 mm diameter pipe 312 b ) 125 mm diameter pipe 313 c ) 150 mm diameter pipe 314 d ) 200 mm diameter pipe 315 e ) 250 mm diameter pipe 316 c.i. sluice valves / fire hydrants & fixturesproviding and fixing c.i. sluice valves ( with cap ) complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) :a ) 100 mm diameterclass i 317 class ii 318 b ) 150 mm diameter class i 319 class ii 320 200 mm diameter class i 321 class ii 322 250 mm diameterclass i 323 class ii 324 300 mm diameter class i 325 class ii 326 constructing masonry chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 ( 1 cement : 4 coarse sand ) for sluice valve, with c.i. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside ) with chained lid and rcc top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i / c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 327 constructing masonry chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 ( 1 cement : 4 coarse sand ) for sluice valve, with c.i. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside ) with chained lid and rcc top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) , i / c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement 3 coarse sand ) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 ( rate only ) 328 constructing masonry chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 ( 1 cement : 4 coarse sand ) for sluice valve, with c.i. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside ) with chained lid and rcc top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) , i / c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 329 constructing masonry chamber 60x60x75 cm, inside in brick work in cement mortar 1:4 ( 1 cement : 4 coarse sand ) for fire hydrants, with c.i. surface box 350x350 mm top and 165 mm deep ( inside ) with chained lid and rcc top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) , i / c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 ( rate only ) 330 air valve & water meter ( bulk type ) : providing and fixing c.i. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete ( the tail pieces, tapers etc if required will be paid separately ) :50 mm dia 331 80 mm dia 332 100 mm dia 333 providing and fixing enclosed type water meter ( bulk type ) conforming to is : 2373 and tested by municipal board complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) :150 mm dia nominal bore 334 200 mm dia nominal bore 335 providing and fixing c.i. dirt box strainer for bulk type water meter with nuts, bolts, rubber insertions etc. complete conforming to is : 2373 :80 mm dia 336 100 mm dia 337 150 mm dia 338 200 mm dia 339 providingandlayings&sc.i.standardspecialssuitablefor mechanical jointing as per is : 13382 :up to 300 mm dia 340 filter feedpump :providingand fixing vertical, inline multistage centrifugalpumpingset ( complete manufactured skid mounted arrangement with manifold and accessories ) withstainlesssteelss 304stage casingandss 304impellerswith stainless steel shaft as per iec standards and gjl250 cast iron suction & discharge casing, connected to tefc ventilated induction motor of 2 pole, 2900 rpm, suitablefor 400 / 440 volts, 3 phase, 50 hz a.c. supply with pressure gauge and with gunmetal isolationcocks, vibrationelimination pads etc. complete with base and frame, nuts and boltsandnecessary rcc foundations as per requirementasper instructionsandpumpshallhave following duty: a ) .no. ofpumps: 3 ( 2 working + 1 standby ) b ) .capacity :2000 lpmc ) .head :35 md ) .capacity :2000 lpm e ) .hp ( motors ) : 75 hp 341 pressure filter ( domestic water ) :providing and fixing vertical dual media pressure filter ( comprising of minimum 300mm bed depth of anthracite and support media and minimum height on straight 2500mm ) fabricated from high performance m.s plate of minimum 10mm thick for shell & 12mm thickfor dished ends ( quality of steel as per is:2062 grade b, thickness as per asme section 8 ) internally treated with coal tar epoxy, complete with air scouring, collection system complete with initial charge of media, m.s facepiping, valves, accessories, external painting with 2 coats of red oxide primer and enamel paint, testing and commissioning complete. ( tested to 5.0 kg / m2 ) a ) .discharge : app.120000 lph ( each ) b ) .filtration rate : 24, 500 lit. / m2 / h c ) .each suggested dia app.:as per manifacture detail 342 water softener:providing and fixing ‘cation’ ion exchange water softener fabricated from minimum 10mm thick m.s. plateon min. shell and 12mm thick m.s. plate on dished ends ( quality of steel as per is:2062 grade b, thickness as per asme section 8 ) complete with initial charge of filter media and ion exchange resins, face piping accessories, diaphragm valves of approved specifications, hdpe brine tank of min. 500 liters, piping testing and commissioning complete with resins of approved quality and make and regeneration assembly complete with valves, ejector, brine suction valves and piping. ( bidder must indicate type and quantity of resin used and quantity of salt required per regeneration ) . all internal parts of the softener shall be rubber lined as per approved specifications.a ) .minimum expected rate of flow:app.32, 000 lph b ) .total soft water to be produced between two regenerations: app. 256 cu.m c ) .expected raw water hardness : app. 450 500 ppmd ) .expected treated water hardness: less than 5 ppm ( zero commercial hardness ) e ) .max. working pressure: 4 kg / cm2 343 cubical panel board plumbing : supply, installation, testing and commissioning of cubical type sectionalised floor standing switch board of 31 mva fault capacity at 415 v complete with 3.5 strip, 160 a capacity aluminium bus bar electrolytic grade, cable alley, switchgears of following capacity & as per specifications.incomer : 600 a tp mccb with heavy duty solid neutral link with ( 0 100a ) ammeter with 3 ct and selector switch, ( 0 500 v ) voltmeter with selector switch, phase indication light withprotection fuse. 01 setoutgoings : i ) for 5 x 75 hp domestic water fixed speed hydroneumatic pumps ( 1 duty + 1 stand by ) ii ) for 2 x 5 hp sump pump ( 1 duty + 1 stand by ) 150 a tp mcb with 40 a dol starter, overload relay, 96 mm ( 0 40a ) ammeter with single ct, start / stop push buttons, on / off / trip indication lights with protection fuse, single phase preventer. 01set. 40a tp mcb with 25 a dol starter, overload relay, 96 mm ( 0 25a ) ammeter with single ct, start / stop push buttons, on / off / trip indication lights with protection fuse, single phase preventer. 01 set....

North Eastern Railways - Uttar Pradesh

29401462 supply of power contactor 70amps,triple pole with auxiliary contacts 2no and 2nc,operating coil voltage 415v a.c,50hzpower contactor 70amps,triple pole with auxiliary contacts 2no and 2nc,operating coil voltage 415v a.c,50hz,power contactor 70amps,triple pole with auxiliary contacts 2no and 2nc,operating coil voltage 415v a.c,50hz to catalogue no.3tf 47 72 0a with suitable overload relay siemens make or exactlyequivalent(including physical dimensions)of abb make(catalogue no.b75 30 00+ca7 22e)or l&t make(catalogue no mnx 70 st19002),confirming to is /iec60947,part4/sec1.as per rcf specification no.edts 041(rev. b).accepted make : siemens, abb,l&t,schneider only.general stores depot uttar pradesh 10.00 numbers...

Uttar Pradesh Jal Vidyut Nigam Limited - Uttar Pradesh

29364347 supply of electrical and mechanical spares required for annual maintenance in rihand hydro power station pipri supply of electrical and mechanical spares required for annual maintenance in rihand hydro power station pipri , buchholz relay 80nb with two micro switch ( one for alarm & one for trip ) , clear view type silica gel breather, 6 kg., flange mounting suitable for 60 mva gt., 11 kv bus duct & 10 mva transformers. , clear view type silica gel breather, 0.5 kg., flange mounting suitable for 500 kva transformers , junction box ( 800x800x300 ) mm, single door , hrc fuse 02 amp. cylindrical type hf , hrc fuse 04 amp. cylindrical type hf , hrc fuse 10 amp. cylindrical type hf , hrc fuse 16 amp. cylindrical type hf , hrc fuse 25 amp. cylindrical type hf , hrc fuse 32 amp. cylindrical type hf , hrc cylindrical 63 amps ( type hf ) , 100 amps ( din type fuse links type hn size 000 ) , 160 amps ( din type fuse links type hn size 00 ) , 200 amps ( din type fuse links type hn size 0 ) , 315 amps ( din type fuse links type hn size 1 ) , araldite packed in 36 gram. tube , locking shim cum pad of rotor fans make as per sample , aloxite resin metal cloth roll, 38 mm wide, 50 mtr long, grit size 400 make bosch / carborundum , dust and damp proof non ferrous pressure gauge for oil pressure, accuracy ± 1%, dial size 4”, range 0 30 psi, connection bottom entry, thread size 3 / 8 bsp, accuracy ± 1% make h guru / warree , dust and damp proof non ferrous pressure gauge for water pressure, accuracy ± 1%, dial size 4”, range 0 30 psi, connection bottom entry, thread size 3 / 8 bsp, accuracy ± 1% make h guru / warree , power contactor, ac3 current rating 16 amps, operating coil 415 volt ac, with 1 no auxiliary contact, make: siemens / abb / / l&t / c&s , microprocessor controlled overload relay with current rating 3 12 amps, size s0 make: siemens / abb / / l&t / c&s , dol starter , copper cable ( flexible ) 4cx 6.0 mm2 , copper cable ( flexible ) 2cx 2.5 mm2 , soft pvc hose with embedded steel wire reinforced, id 19 mm, od 25 mm , soft pvc hose with embedded steel wire reinforced, id 25 mm, od 32 mm , hand lamp set , carbon brush for slip ring , carbon brush holder...

Uttar Pradesh Power Transmission Corporation Limited - Uttar Pradesh

28827243 work of providing and fixing of auxiliary contactors and overload relays in marshalling box for auto operation of cooling fans of transformers at various substations under etd hamirpur work of providing and fixing of auxiliary contactors and overload relays in marshalling box for auto operation of cooling fans of transformers at various substations under etd hamirpur...

Kisan Sahkari Chini Mills Limited - Uttar Pradesh

28813990 supply of all type electrical goods, lighting goods and pvc cable etc supply of all type electrical goods, lighting goods and pvc cable etc , steelgrip make p.v.c. insulated tape size 19mm x 10 meter , cotton tape , firex tape , pendent holder ( white colour ) make arkalyte / anchor 5 amp. , hand lamp with glass cover , pendent holder , stag b paste ( 500 gram ) , wdg 40 ( 500 ml ) , lithium complex grease mobil unirex n3 , silica gel for transformer , taparia make tools for electrical work ( screw driver set ) , taparia make tools for electrical work ( pach tester set for wireman ) , multimeter p 3 make sanwa pocket type , digital multimeter make flukemodel 107 , tong tester ( digital ) fluke make model 305 , meggar motwani make for 440 v.model d2 km , meggar motwani make for 11 kv.model d2 km , p.v.c. copper wire ( 1.5 mm2× 1core ) ( national / polycab ) make , p.v.c.copper wire ( 2.5 mm2 × 1 core ) ( national / polycab ) make , p.v.c. copper wire ( 4 mm2 × 3core ) ( national / polycab ) make , p.v.c. copper wire ( 6 mm2 × 3core ) ( national / polycab ) make , p.v.c.copper wire ( 1.5 mm2 × 3core ) ( national / polycab ) make , p.v.c. copper wire ( 2.5 mm2 × 3core ) ( national / polycab ) make , p.v.c.copper wire ( 4 mm2 × 4 core ) ( national / polycab ) make , p.v.c.copper wire ( 4 mm2 × 2 core ) ( national / polycab ) make , p.v.c. copper wire ( 10 mm2 × 3 core ) ( national / polycab ) make , p.v.c. copper wire ( 6 mm2 × 3 core ) ( national / polycab ) make , p.v.c. copper wiresize 40 / 76, 2 core ( national / polycab ) make , p.v.c. wirecopper ( 4 mm2 × 3core ) ( national / polycab ) make , p.v.c. wirecopper ( 2.5 mm2 × 2core ) ( national / polycab ) make , single phase 230 / 24 volt step down transfermor 1 kva having on / off switch & 5 nos. plug base with switches 5 amp. in output , hrc fuse ( 63 et ) fuse , 690 v , bs 88:4bussmann make , 415 v a.c. 24 v dcrectifier for solenoid valve ( mic make ) , 16 amp rotary switch dp ( salzer make ) , led tubelight fitting 20 wbajaj make , led bulb 14 w ( orpat make ) bajaj make , led bulb 9 w ( orpat make ) bajaj make , hpmv fitting complete with choke 400 w bajaj make , hpsv fitting complete with choke 250 wbajaj make , hpsv fitting complete with choke 250 w bajaj make , hpmv fitting complete with choke 250 wbajaj make , hpmv fitting complete with choke 150 wbajaj make , hpsv lamp ( 250 w ) tubular ( bajaj ) , hpsv lamp ( 400 w ) tubular ( bajaj ) , mh lamp ( 150 w ) tubular ( bajaj ) , hpsv lamp ( 150 w ) ( bajaj ) , hpsv lamp ( 70 w ) ( bajaj ) , mh lamp ( 250w ) tubular ( bajaj ) , hpmv lamp ( 80 w ) es ( bajaj ) , hpmv lamp ( 400 w ) ( bajaj ) , hpmv lamp ( 400 w ) spherical ( bajaj ) , mh lamp ( 400 w ) tubular ( bajaj ) , hpsv choke ( 250w ) ( bajaj ) , hpmv choke ( 400 w ) ( bajaj ) , hpmv choke ( 80 w ) ( bajaj ) , hpmv choke ( 150 w ) ( bajaj ) , hpmv choke ( 70 w ) ( bajaj ) , hpsv choke ( 150 w ) ( bajaj ) , hpsv choke ( 400 w ) ( bajaj ) , bjbi / mbi400 w ( mv / mmh ) choke 240 volt. ( bajaj make ) , bjbi / mbi250 w ( mv / mmh ) choke 240 volt. ( bajaj make ) , mv / sv lamp holder ( 400 w ) , mv / sv lamp holder ( 250 w ) , mv / sv lamp holder ( 150 w ) , led flood light for street lighting ( 25w ) with complete fitting ( bajaj / surya / halonix ) , led flood light for street lighting ( 60w ) with complete fitting ( bajaj / surya / halonix ) , led flood light for street lighting ( 90w ) with complete fitting ( bajaj / surya / halonix ) , led flood light for street lighting ( 120w ) ( bajaj / surya / halonix ) , electronic choke for 36 / 40 w tubelight ( bajaj ) , electronic ignitor 240 v , glass holder for 70 / 80 w ( sv / mv ) lamp , c.t. 100 / 5a cl 1, 10va ( procom make ) , c.t. 125 / 5a cl 1, 10va ( procom make ) , c.t. 200 / 5a cl 1, 10va ( procom make ) , c.t. 250 / 5a cl 1, 10va ( procom make ) , c.t. 400 / 5a cl 1, 10va ( procom make ) , control t / f 1.0 kva ( logistatemake ) , control t / f 1.5 kva ( logistatemake ) , control t / f 2.0 kva ( logistatemake ) , direct type ammeter 0 20 / 120a ( ae make ) , direct type ammeter 0 25 / 150a ( ae make ) , direct type ammeter 0 30 / 180a ( ae make ) , direct type ammeter 0 50 / 300a ( ae make ) , direct type ammeter 0 60 / 360a ( ae make ) , electronics logo timer ( type 6ed1052 1fb00 obab ( siemens make ) , timer range 3 sec to 30 minute ( eapl electromic ) , rotary c / o switch 25a dp ( salzer make ) , start push button green with 1 no element, rcb2 ba3, rb2 be 101 ( rass make ) , stop pursh button red with 1 nc element, rcb2 ba4, rb2 be 102 ( rass make ) , volt. selector swithc ( salzer make ) , voltmeter 0 500vac ( ae make ) , 10a push button for grab complete assembly open / close ( mushroom ) ( sp make ) , 10a push button for hyd. on 7 off ( mushroom ) ( sp make ) , 23 32a overload relay for hydraulic motor ( l&t make ) , 415vac / 24vcd rectifier for solenoid valve ( mic ) , 7.5hp resistance box for l.t. motor ( soc / sns / sa ) , 0 60sec. timer forl.t. moror ( bch ) , 32a contactor for l.t. motor ( rotar ) ( c&s make ) , carbon brush grade be 22, size t 20, w 40, l 50mm ( leveller motors ) ( crompton greaves make ) , carbon brush grade be 22, size t 20, w 40, l 50mm ( chopper motors ) ( crompton greaves make ) , carbon brush grade c 80 x, size t 20, w 40, l 50mm ( fibrizer motor ) ( crompton greaves make ) , carbon brush size t 8, w 20, l 22mm ( cane unloader ) , carbon brush holders ( cane unloader lt motors ) bharat bijlee m / n m1509012 , slip ring for cane unloader motor ( lt & ct ) , fibrizor lrs contactor model no.3rt 1075 6, current 430a, 8kv ( siemens make ) , fibrizor lrs contactor model no.3rt 1064 6, current 275a ( siemens make ) , auxillary contactor, model 3th 30, 22 oa ( siemens ) , plc logo bm230 rce, 1p 6ed 1052 1fb00 obab ( siemens ) , holder screw typefor 70 watt light ( bajaj / crompton ) , glass for sv / mv lamp , capacitor 2.5 mfd , capacitor 4 mfd , capacitor 10 mfd , capacitor 20 mfd , capacitor 42 mfd , capacitor 3.15 mfd , capacitor 34 mfd , capacitor 8 mfd , capacitor 64 mfd , holder screw typefor 250 / 400 watt lamp ( bajaj / crompton ) , holder for 80 watt lamp ( bajaj / crompton ) , holder for 150 watt lamp ( bajaj / crompton ) , tube light ballast 36 / 40 watt ( bajaj / crompton ) , pin type bulb 60 watt , pin type holder , mcb ( 1 pole ) 6 amp ( siemens make ) , mcb ( 1 pole ) 10 amp ( siemens make ) , mcb ( 2 pole ) 16 amp ( siemens make ) , mcb ( 1 pole ) 16 amp ( siemens make ) , mcb ( 3 pole ) 10 amp ( siemens make ) , mcb ( 3 pole ) 16 amp ( siemens make ) , mcb ( 3 pole ) 25 amp ( siemens make ) , mcb ( 3 pole ) 32 amp ( siemens make ) , mcb ( 3 pole ) 63 amp ( siemens make ) , mcb ( 3 pole ) 100 amp ( siemens make ) , mcb ( 4 pole ) 25 amp ( siemens make ) , mcb ( 4 pole ) 32 amp ( siemens make ) , mcb ( 4 pole ) 63 amp ( siemens make ) , mcb ( 4 pole ) 100 amp ( siemens make ) , relay6 10 amp , 24 v power supply transformer 230 / 24v with enclosure ( 500va range ) , no contact with push button ( green ) , no contact with push button ( mushroom type ) , elemax ( ctb 04 sqmm ) tbconnectwell cts25un, iec60947 7 1, 1000v , elemax ( ctb 06 sqmm ) tbconnectwell cts25un, iec60947 7 1, 1000v , elemax ( ctb 10 sqmm ) tbconnectwell cts25un, iec60947 7 1, 1000v , elemax ( ctb 16 sqmm ) tbconnectwell cts25un, iec60947 7 1, 1000v , elemax ( ctb 25 sqmm ) tbconnectwell cts25un, iec60947 7 1, 1000v , elemax ( ctb 35 sqmm ) tbconnectwell cts25un, iec60947 7 1, 1000v , elemax ( ctb 50 sqmm ) tbconnectwell cts25un, iec60947 7 1, 1000v , elemax ( ctb 70 sqmm ) tbconnectwell cts25un, iec60947 7 1, 1000v , motor terminal ( 18.5 kw ) , motor terminal ( 3.7 kw ) , motor terminal ( 0.18 kw ) , motor terminal ( 15 kw ) , lug paste , pvc copper armoured cable ( 4 mm² x 4 core ) , pvc copper armoured cable ( 4 mm² x 3 core ) , pvc copper armoured cable ( 6 mm² x 3 core ) , pvc workshop flexible copper wire ( 40 / 76 x 3 core ) , safety hand gloves ( for ht line ) , industrial shoes for ht line , button type switch ( 5 amp ) , button type holder ( 5 amp ) , lugs aluminium 10 sq mmferrul type dowellsmake , lugs ( aluminium ) 25sq mmferrul type dowellsmake , lugs ( aluminium ) 35 sq mmferrul type dowellsmake , lugs ( aluminium ) 50 sq mm ferrul type dowellsmake , lugs ( aluminium ) 70 sq mm ferrul type dowells make , lugs ( aluminium ) 95 sq mm ferrul type dowellsmake , lugs ( copper ) 6 sq mmferrul type dowells make , lugs ( copper ) 10 sq mmferrul type dowells make , lugs ( copper ) 25 sq mmferrul type dowells make , lugs ( copper ) 16 sq mmferrul type dowells make , lugs ( copper ) 4 sq mm ferrul type dowells make , lugs ( copper ) 2.5 sq mmferrul type dowells make , lugs ( copper ) 1.5 sq mm ferrul type dowells make , lugs aluminium 10 sq mm ring type dowellsmake , lugs ( aluminium ) 25sq mmring type dowellsmake , lugs ( aluminium ) 35 sq mmring type dowellsmake , lugs ( aluminium ) 50 sq mm ring type dowellsmake , lugs ( aluminium ) 70 sq mm ring type dowells make , lugs ( aluminium ) 95 sq mm ring type dowellsmake , lugs ( aluminium ) 120 sq mm ring type dowells make , lugs ( aluminium ) 185 sq mm ring type dowells make , lugs ( aluminium ) 240 sq mm ring type dowellsmake , lugs ( copper ) 6 sq mmring type dowells make , lugs ( copper ) 10 sq mmring type dowells make , lugs ( copper ) 25 sq mmring type dowells make , lugs ( copper ) 35 sq mmring type dowells make , lugs ( copper ) 4 sq mm ring type dowells make , lugs ( copper ) 2.5 sq mmring type dowells make , lugs ( copper ) 1.5 sq mm ( ring type ) dowells make , lugs ( copper ) 6 sq mmpin type dowells make , lugs ( copper ) 10 sq mmpin type dowells make , lugs ( copper ) 25 sq mmpin type dowells make , lugs ( copper ) 16 sq mmpin type dowells make , lugs ( copper ) 4 sq mm pin type dowells make , lugs ( copper ) 2.5 sq mmpin type dowells make , lugs ( copper ) 1.5 sq mm ( pin type ) dowells make , semi conductor fuse 16 amp. , semi conductor fuse 250 amp. ( 170 m 3116 ) 690vbussmann denmark make , semi conductor fuse 400 amp. ( 170 m 4112 ) 690vbussmann denmark make , semi conductor fuse 630 amp. ( 170 m 4116 ) 690vbussmann denmark make , semi conductor fuse 800 amp. ( 170 m 4118 ) 690vbussmann denmark make , led indicator lamp red 110v , led indicator lamp yellow 110v , led indicator lamp blue 110v , led indicator lamp red 240v , led indicator lamp yellow 240v , led indicator lamp blue 240v , tia type hrc fuse 16 amp. , tia type hrc fuse 32 amp. , ns type hrc fuse 2 amp. , ns type hrc fuse 4 amp. , ns type hrc fuse 6 amp. , ns type hrc fuse 10 amp. , digital multimeter 1000volts , temperature gun 250 degree , digital meggar ( 0 500v ) 2.5 kv , rotary switch 3 pole salzer make , brushless fan ( 3.5x 3.5 ) , brushless fan ( 5x 5 ) , wire cutter , wire stripper , o / l relay ( phase failure relay ) 415v , o / l relay ( miniature relay ) rxm 2a b2ed , contactor ca 3kn 31fd 110volts , phase tester 816 taparia make , combination plier 8 , copper carbon brush ( 8x16x35 ) mm , auxillary contact block 3rh2911 , push button element no , push button element nc , exhaust fan heavy duty 1400rpm , doctor beck lufta 1a varnish for motors , bus bar300 amp 4 pole , change over switch 400 amp, 4 pole ) complete set , clamp tester ( meco make ) , digital tachometer ( microprocessor based ) , switch fuse unit with box 250 amp. , switch fuse unit with box 400 amp. , no contact siemens make , nc contactsiemens make , screw driver 8 with star set , tubular box spanner 24 x 27taparia make , armoured aluminium cable size 10 mm2 x 2 core ( polycab make ) , armoured aluminium cable size 25 mm2 x 3.5 core ( polyacabmake ) , armoured aluminium cable size 35 mm2 x 3.5 core ( polyacabmake ) , armoured aluminium cable size 50 mm2 x 3.5 core ( polyacabmake ) , armoured aluminium cable size 70 mm2 x 3.5 core ( polyacabmake ) , armoured aluminium cable size 95 mm2 x 3.5 core ( polyacabmake ) , armoured aluminium cable size 120 mm2 x 3.5 core ( polyacabmake ) , armoured aluminium cable size 150 mm2 x 3.5 core ( polyacabmake ) , armoured aluminium cable size 185 mm2 x 3.5 core ( polyacabmake ) , armoured aluminium cable size 240 mm2 x 3.5 core ( polyacabmake ) , armoured copper cable size 2.5 mm2 x 3 core ( polycab make ) , copper flexible cable 1.5 mm2 x 12 core ( polycab make ) ...

Firozabad Municipal Corporation - Uttar Pradesh

28721130 supply of electrical items connection plate , panel starter , condensor , terminal patti strip , lugs , bottle lugs , overload relay , valve meter , ampere meter , ct meter , base plate , coil , change over , main switch , cut out , single core pvc auto wirre coper , aluminum cable , flate copper cable , coooper lead , kit set , thermal timer , timer starter , moving contactor , magnet coil , contactor , sumbersible pump set , motor pump set , pump set , pump , gloves , battery , tape cello tape , plas plier , transformer oil , clamp meter digital meter , mcb , stop switch , start switch delta switch , preventor mini lake pump protection relay , minilake current sensor , 123 mccb 630 amp i.s.i 124 mccb 400 amp i.s.i 125 mccb 125 amp i.s.i 126 mccb 100 amp i.s.i 127 mccb 163 amp i.s.i 128 mccb 200 amp i.s.i push button , series 3 indicator, single indicator , indicator , tester , screw driver focus , 133 testar i.s.i 134 screw driver focus 808 / 400 i.s.i 135 joint patti i.s.i 136 tomy 8 no / 10 / 7v i.s.i efi starter cotton cloth , red green button , sand file half round , oil starter immersed 147 s.r no. 147 to 160 jyoti make for statrar set of base plate i.s.i 148 set of terminal links abc i.s.i 149 set of overload relay i.s.i 150 set of connection links between contact and realy i.s.i 151 terminal block with links i.s.i 152 megnet coil rated 415v / ac i.s.i 153 megent coil ( small loop ) i.s.i 154 set of push button assly i.s.i 155 type rz 11 having actualing time rang 3 to 12 secc i.s.i 156 auxililary switch type 01 1 no+nc contacts i.s.i 157 set of terminal serew and washer i.s.i 158 full wairing starter i.s.i 159 set of moving power contacts i.s.i 160 set of fixed power contact i.s.i 161 s.r no. 161 to 174 kilvarn make for statrar set of base plate i.s.i 162 set of terminal links abc i.s.i 163 set of overload reay i.s.i 164 set of connection links between contact and realy i.s.i 165 terminal block with links i.s.i 166 megnet coil rated 415v / ac i.s.i 167 mgenet coil ( small loop ) i.s.i 168 set of push button assly i.s.i 169 type rz 11 having actualing time rang 3 to 12 secc i.s.i 170 set of terminal serew and washer i.s.i 171 full wairing starter i.s.i 172 auxililary switch type 01 1 no+nc contacts i.s.i 173 set of fixed power contact i.s.i 174 set of moving power contacts i.s.i 175 s.r no. 175 to 188 bentax make for statrar set of base plate i.s.i 176 set of overload reay i.s.i 177 set of terminal links abc i.s.i 178 set of connection links between contact and realy i.s.i 179 terminal block with links i.s.i 180 megent coil rated 415v / ac i.s.i 181 megent coil ( small loop ) i.s.i 182 set of push button assly i.s.i 183 type rz 11 having actualing time rang 3 to 12 secc i.s.i 184 auxililary switch type 01 1 no+nc contacts i.s.i 185 set of fixed power contact i.s.i 186 set of moving power contacts i.s.i 187 set of terminal screw and washer i.s.i 188 full wairing starter i.s.i 189 s.r no. 189 to 201 advance make for statrar set of base plate i.s.i 190 type rz 11 having actualing time rang 3 to 12 secc i.s.i 191 set of terminal links abc i.s.i 192 megnet coil rated 415v / ac i.s.i 193 megnet coil ( small loop ) i.s.i 194 set of connection links between contact and realy i.s.i 195 terminal block with links i.s.i 196 on / off push button assly i.s.i 197 set of terminal serew and washer i.s.i 198 loose oil leemered contract 25 amp i.s.i 199 set of wairing full starter i.s.i 200 set of fixed power contacts i.s.i 201 set of moving power contacts i.s.i 202 s.r no. 202 to 214 mug 30 make for statrar set of base plate i.s.i 203 set of terminal links abc i.s.i 204 set of overload relay i.s.i 205 terminal block with links i.s.i 206 megent coil rated 415v / ac i.s.i 207 megnet coil ( small loop ) i.s.i 208 set of moving power contacts i.s.i 209 set of fixed power contacts i.s.i 210 full wairing starter i.s.i 211 type rz 11 having actualing time rang 3 to 12 secc i.s.i 212 auxililary switch type 01 1 no+nc contacts i.s.i 213 set of terminal and serew washer i.s.i 214 on / off push button assly i.s.i 215 s.r no. 215 to 229 bch make for statrar set of base plate i.s.i 216 set of terminal links abc i.s.i 217 set of overload reay i.s.i 218 terminal block with links i.s.i 219 megenet coil rated 415v / ac i.s.i 220 magnet coil ( small loop ) i.s.i 221 on / off push button assly i.s.i 222 type rz 11 having actualing time rang 3 to 12 secc i.s.i 223 auxiliary switch type 01 1 no+nc contacts i.s.i 224 plunger pir 60 amp aux switch i.s.i 225 set of moving bridge i.s.i 226 set of moving power contacts i.s.i 227 set of fixed power contacts i.s.i 228 set of terminal and serew washer i.s.i 229 full wiring starter i.s.i ampere meter ct coil , connection plate over load , connection plate or contactor jointing copper strip patti , contactor cm , mnx contactor , starter , main switch ampere etc...