Rural Engineering Department - Uttar Pradesh

37970092 tender for construction of computer lab / room at g.g.i.c. manpurhari, mainpuri 1 excavation in foundation in ordinary soil (loam, clay, or sand ) includinglift upto 1.50 m and lead upto 30m including filling watering and raming of excavated earth into the trenches or into the space between the building and the sides of foundation tranches or into the plinth and removal and disposal of surplus earth as directed by the engineer incharge upto a distance of 30m from the foundation trenches. sino.251 2 antitermite treatment of soil under floors using chemical emulsion @ one litre per hole, 300 mm apart @ 100 nos holes per 9.00 sqm. including drilling 12 mm diameter holes and plugging also to match the floor properly : with chlorpyriphos / lindane e.c. 20% with 1 3 providing and laying cement . concrete in 1:6:12 (1 cement : 6 fine sand : 12 graded brick ballast aggregate 40 mm nominal size ) includingsupply of all materials , labour and t & p etc. required for completion of work and curing complete , including cost of form work . in foundation and floors. s.i. no. 273(a) 4 providing and laying cement . concrete in 1:4:8 (1 cement : 4 coarse sand : 8 graded brick ballast aggregate 40 mm nominal size ) includingsupply of all materials , labour and t & p etc. required for completion of work and curing complete , including cost of form work . in foundation and floors. s.i. no.3/4.1 5 class m 150 brick work in 1:6 cement and coarse sandmortar in foundation and plinth including supply of all material labour and t&p etc. required for proper completion of work. s.i. no. 1/6.1 6 earth work in cutting or in embankment in ordinary soil excavation to be in the form of a regular pits not exceeding 0.50m in depth and earth work in embankment to be in 20cm layers including ramming and dressing the surface to required levels and slopes and also including 1.5 m lift and 3 km lead. the earth in form of cutting to be used as spoil banks within 50m distance as directed by the engineer in charge. si no.253+253(d) 7 rcc work providing and laying in position specified grade of reinforced cement concrete in raft foundation, including the cost of centering, shuttering, finishing and excluding reinforcement all work up to plinth level in :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size).si no.10/5.1 8 rcc work providing and laying in position specified grade of reinforced cement concrete,slab including the cost of centering, shuttering, finishing and excluding reinforcement above plinth level upto fifth floor level in :1:1.5:3 (1 cement : 1.5 coarse.si no.11/5.1 9 mild steel or iron work in plain work such as reinforced concrete or rinforced brick work ( when not included in and an over all rates) brought to required shape as necessary including bending for proper completion of the work and including the suplly of steel and its wastage bend. hooks and authorized over lapping shell be muasured upto floor to level. (for12 mm.) s.i no 504 10 class m 150 brick work in 1:6cement and coarse sand mortar in super structureincluding supply of material labour and t&p etc. required for proper complition of work. s.i.no.6.1+6.8a 11 class 150 (non modular) brick work in 1:4 cement and coarse sand mortar in foundation and plinth including supply of all materials, labour and t&p etc. required for proper completion of the work.si no.6.1+6.8a 12 15mm cement plaster with cement mortar in proportion of 1:4 cement & coarse sand of single coat for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm in girth and finished even and smooth.si no.7/13.5 13 12 mm. cement plaster in (1:4) cement and coarse sand in singlecoat onfairside of single or half brick wall for interior plastring upto floor to level including internal rounded angles chamfers , and/ or rounded angles not exceeding 80mm in girth and finished even and smooth. no extra mixing any additive. s.i. no. 2/13.4 14 mild steel and iron work of small size and section such as holding down woods, hold fasts tierods, grating, etc. (when not included in and over all rates) brought to required form including supply of steel and its wastage including cost of bolts, nuts if required for proper completion of work including fabrication of holes in door chaukhats and nosing.si no.502 15 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes.110 mm diameter. 16 supply and fixing of flush doors, commercial quality conforming of i.s. 2202 part 1 (1983) including isi marked oxidized iron fitting with screws, bolt hinges,handles,siliding bolt, door stopper and tower bolt etc.32 mm thick. 17 supply and fixing fly and mosquitos proof stainless steel grade 304 wire mesh gauge with 0.50mm dia wire and 1.40mm wide aperture and including supply of c.p. teakwood batten 8cmx1cm (3x3/8)/flat iron 25mmx4mm and including supply of necessary screws all materials, labour, t&p etc. required for proper completion of work.ch.9,si no.18/455(a) 18 cementconcreteflooring1:2:4(cement ,c/sand and 12.5 mm stone grit) lai in one layer finished with floating coat of neat cement .(25 mm thick floor) 19 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone of size 20mm nominal size) laid in one layer finished with floating coat of neat cement (40mm thick floor).ch.14,si no.5/665 20 providing and fixing glass strips of 4mm thick in joints of floor and skirting at the time of laying including labour, t&p etc. complete in all respect.(2.2mm thick)si no.25/631 21 finishing walls with pop approved brand and manufacture and of required shade on undacorated wall surface to give even shade over including curing and cost of all material, labour, t&p etc. required for proper completion of work.ch.15,si no.30 22 distemperring with oil bond distemper of approved brand(three coats) and of required shade on undecorated wall surface to give an even shade over and including priming coat whiting after thoroughly brushing the surface free from dropping andother foreign matter including preparing the surface even and sand papered smooth.s.i. no. 13/649.+650 23 distemperring with oil bond distemper of approved brand(two coats) and of required shade on undecorated wall surface to give an even shade over and excluding priming coat after thoroughly brushing the surface free from dropping andother foreign matter including preparing the surface even and sand papered smooth.s.i. no. 14/650 24 painting two coat over priming coat on newsteel and other metal surfaces upto 10cm width or girth or small articles not exceeding 0.10 sq.m. in area with superior synthetic enamel such as luxol 3, hi gloss apcolite, superlac, dulux specified brushing to give and even shade and including the cleaning the surface of all dirt, dust and other foreign matter sand papering and scrapping including cost of all materials, labour, tools and plants etc. required for proper completion of work.si no.641+19.29+642 25 painting two coats on new surface of wood with superior synthetic enamel such as luxol3, hi gloss apcolite,superlac,dulux spesified brusing to give and even shade and including the cleaning the surface of all dirt, dust and other foraign matter sand papering and scraping including cost of all materials, labour and t & p etc. required for proper complition of work. s.i. no.641+19.73+642 26 making grooves 10 to 12mm wide x 8mm deep in plaster of the wall or in ceiling vertically or horizontally as required. 27 s/f marble stone patiya etc. all complete. 28 wiring point for light with 1.5 sq.mm.frlshpvcinsulated multistrand single core copper conductor cablein pvc conduit partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 1.5 sq. mm.frlsh pvc insulated multistrand copper conductor cable as earthwire drawn inside,gp box, piano type switch & ceiling rose/angle/batten holder on 3mm thickphenolic laminated backalite sheet etc complete in all respect as directed including matching colour wash.si no. 138 c 29 wiring point for fan / fresh air fan (light duty exhaust fan) with 1.5 sq.mm.frlsh pvc insulated multistrand single core copper conductor cable in pvc conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting,complete with 1.5 sq. mm.frlsh pvc insulated multistrand copper conductor cable as earthwire drawn inside,gp box , piano type switch & ceiling rose on 3 mm. thick backelite sheet etc., complete in all respect including matching colour wash.si no. 140 c 30 wiringpointforplugwith 1.5 sq. mm.frlsh pvc insulated multistrand single core copper conductor cable inpvc conduit partly concealed in wall and partly laid in slab alongwith the reinforcementbefore concreting, complete with 1.5 sq. mm.frlsh pvc insulatedmultistrandcopperconductorcable asearthwire drawninside the conduit. and piano typeswitch and socket etc., complete in all respect including matching colour wash. si no. 141 c 31 supply and fixing of power plug with 20 amp./250 voltflush type modular switch and 5 pin 20 a/250 volt flush type universal modular socketswitch on concealed m.s boxincluding supply of all material, labour t&p etc. required for proper completion of work. si no. 1139 a 32 s/f ofcomputer point with2 no. 5amp. 5 pin plug with switch and socket on concealed m.s. box including supply of all material, labour t&p etc, required for proper completion of work for computer. si no. 2 *(141c) 33 supply and fixing of electronic fan regulator( modular) 120 280 v. isi marked, on the existing switch board including making connections, required material, labour t&p etc. for proper completion of work to the satisfaction of engineer in charge of work. si no. 1203 c 34 supply and fixing ofled tube light with batten suitable for up to 1 x 22 watt led tube light fittingincluding tube on surface complete in all respect. si no. 1413a cat a 35 supply and wiring of submain with two number2.5sq.mm. frlsh pvc insulated 1100 v grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2mm thick) pvc conduit partly laid in slab alongwith reinforcement before concreting and partly concealed in wall, with 1 nos. 1.5 sq. mm. frlsh pvc insulated 1100 v grade multistrand single core copper conductor cable as earth continuity wire drawn inside the conduitetc, complete in all respects including matching colour wash. si no. 1307 c 36 s & f surface/flush mounting 12 ways spn distribution board with additional metal doorwithout mcb complete in all respect, asdirect by engineer in charge. s.i. no. 1025 a cat b 37 s&f of 6 amp to 32 amp. spmcb (10 ka) c curve si no. 1002 cat a 38 s&f of 32amp. dp mcb (10 ka) c curve si no. 1009 cat a 39 supply and fixing hexagonal/roundg.p.fan box of approved make made up of 1.0 mm thickisi marked g.p.sheet spot welded four to eightholes of 25.4 mm for pipe entryof the box. holes should be semi shuttered type with 0.5 mm g.p. sheet made upper & lower cover duly screwed fitted with 300 mmround zink coted m.sbar x 12 mm& brand name should be embossed. fixing with wiring conduit laid in the r.c.c. roof before concretingalongwith supply of all material, labour, t&p etc. required for proper completion of the work. si no. 1149 40 supply of bee 5 star rated 1200mm sweep ceiling fans with fan motor of a.c permanent insulation,capacitor rating confirming bee 5 star rating and is:374/79 and also comply with is:1709/1984 with latest amendment. the rated voltge 220/240 volts, 50hz, 1 ph ac the fan assemble should consists of down rod blades, shackle canopies etc and with double ball bearing system. si no. 1501 (i) 41 erection and testing of ceiling fan and regulator for room height upto 3.5 metres including supply of 3mm thick g.i.pipe19mm dia. duly painted, complete in all respect. si no. 1116 42 add for invertor wiring in wiring point for light/ fan/ plug with 1.5 mm cu wire si no. 189 ...

Uttar Pradesh Jal Nigam - Uttar Pradesh

37275983 tender for rates for supply of materials & piece rated works ( labour rates ) at 08 nos additional class room in govt. girls inter college etawah ( nit no 306 / e nivida / 46 dt. 15 04 2023 ) 1 cement ( opc / ppc ) 2 coarse sand 3 fine sand 4 brick m 150 5 tor steel 8mm dia 6 tor steel 10 mm dia 7 tor steel 12mm dia 8 tor steel 16mm dia 9 tor steel 20mm dia 10 binding wire 11 stone grit 10 20mm 12 stone ballast 40mm 13 white cement 14 brick bats 15 flush door ( single leaf 35mm ) 16 flush door ( double leaf 35mm ) 17 angle iron ( 40x40x5 ) 18 10mm square bar 19 z section ( f4 & f7 ) 20 hold fast 21 sliding bolt ( 250x16 ) 22 tower bolt ( 250x10 ) 23 ms handle125mm 24 door stopper 25 obd paint ( 20 lt ) 26 exterior paint ( 20 lt ) 27 enamel paint ( black ) 20 lt 28 putty ( 40 kg ) 29 red oxide ( 20 lt ) 30 glass panes 4mm thick 31 glass strip 32 ss railing 33 pvc pipe 110mm ( 4 inch ) 34 pvc elbow 110mm 35 pvc socket 110mm 36 pvc tee 110mm 37 pvc solvent 38 ms clamp 110mm 39 moduler ms box ( 8x3 ) with sheet 40 conduit pipe 20mm 41 surface junction 20mm 42 pvc bend 20mm 43 pvc saddle 20mm 44 m.s. fan box 45 cico tapecrete p151 46 heptrachlor 47 earth work inexacavationin trenchesfor foundations and for pipes cables etc.inordinary soil ( loan clay orsand ) including lift upto 1.5 mand leadup to 30m.&including filling watering& ramming of excavated earth in to trenchesor into the space betweenthe building & the sides of foundation trenchesorinto the plinthandremoval&disposal of surplusexcavated earthas directed by the engineer i / c upto a distance of 30 m from the foundation trenches. 48 fillingof carted earth. 49 labour charge for laying cement concrete 1:4:8 ( 1 cement :4 fine sand :8 graded brick aggregate 40 mm nominal size ) and curing complete, in foundation and floors. 50 labour charge for post constructinal injecting antitermite treatment as per specification. 51 labour charge for r.c.c. workwith cement approved coarse sandand2cm. ( 3 / 4 ) guageapprovedstoneballastin the proportion 1:2:4, ( 1 cement :6 coarse sand :4 stone gritt. ) in lintels of doors and windows. including tools and plants etc, required forproper completion of the works. strength of the concrete shall not beless than m 15. 52 as in item 51 above but for f.f. add 1% for f.f 53 as in item 51 above but forslabs ( using 1:1.5:3 mix concrete ) 54 as in item 53 above but forslab f.f. add 1% for f.f 55 as in item 51 but for thelighterbeams i.e. havingspans upto 6 m. ( using 1:1.5:3 mix concrete ) 56 as in item 55 above but forbeam f.f. add 1% for f.f 57 as in item 51 abovebut inr.c.c.raft foundation and footing ( using1:1.5:3mix concrete ) 58 as in item 51 above but in r.c.c. columns in1:1.5:3having strength not less than m 200 59 as in item 58 above but forcolumn f.f. 60 labour charge for centering and shuttering including strutting, propping etc. and removal of form forfoundations, footings, bases of columns, etc. for mass concrete 61 labour charge for centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers 62 labour charge for centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts 63 labour charge for centering and shuttering including strutting, propping etc. and removal of form suspended floors, roofs, landings, balconies and accessplatform 64 labour chaege for brick work in1:6cement and coarsesandof1.25finenesmodulus mortar infoundation and plinth , including tools and plants etc. requiredforpropercompletion of the work. 65 same as in item no.59above but in super structureaboveplinth levelup to floor two level ( up to two storeys ) including necessarycutting andmouldingofbrickworkas requiredandalsoincludinghoney combed brick work in thickness of wall more than 12cms. 66 as in item no 60 above but forf.f. 67 same as in item no.59 but in1:3 cement and coarse sand mortar in superstructure for wall thickness 12 cms & below. 68 labour charge for layingdampproof coarse 25 mm thickwithcement concrete 1:1.5:3 ( 1 cement:1.5 coarsesand :3 graded stoneaggregates 13 mm nominalsize ) andcuring complete. 69 labour charge for paintingon d.p.c. withtwocoatsof airblown bitumen 85 / 50or 85 / 25 @ 1.7 kg / sqm approx. 70 labour charge for layingbrick coba 12mm thick laid with m.150 class brick bat coba 7.50cm. thick with gap of 15mm to each other. over 20mm. thick base of cement morter 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with aerelic cement concrete waterproofing compound filed gaps of coba & top of coba mortar mixed with water proofing compoond. in 1:4 cement & coarse & morter finished smooth & top mashed false square 30cmx30cm. & side wall parapet shall be mono tythic plaster wall up to 30cm.higher & junction & corner shall be rounded by brick ballast cement and coarse sand masonary coba with top finished mixed with acetic water proofing compound @ 2% by weight &including t & p etc. com.for proper completion of work. 71 labour charge forfixingof flushdoors commercialqualityconformingtoi.s. 2202 part i ( 1983 ) includingfixingofwoodencleats andstoppers and including ixing andadjustment of hinges, bolts, locks, handle, springs and other fittingsbut excludingtheir supply and including painting with two coats of black japan painton alliron fitting if necessary.fittingwith necessaryscrews to be supplied departmentally. ( a ) 35 mm thick 72 four double leaf shutters addextra in over all rates. 73 labour charge for fabrication of holdfastfordoor chaukhats and windows. 74 labour charge for fabrication of grill / staircase railing. 75 labour charge for fabrication ofz section steel windows. 76 labour charge for fabrication of angleiron doorchaukhat of 40*40*5 mm. 77 labour charge for fixingofsteelorwoodenchaukhats in position. door chaukhats 78 labour charge for fixingofsteelorwoodenchaukhats in position. window chaukhats 79 labour charge for mild steel or iron in plain work such as reinforced concrete or reinforced, brick work ( whennot includedin anover all rates ) wroughttorequired shapeas necessary including cutting, bending and binding for proper completion of the workupto floor two level. 80 labour charge for 12mm thick plaster onoutersurfacewalls consistingor 12mm thick backingcast of cement mortar. 1:6 ) 1 cement:6 coarse sand 81 labour charge for 12 mm cement plasterinsingle coat on rough sideofsingle orhalfbrick wall for interior plastering up to floor twolevelincludinginternalrounded angles not exceeding80mm ingirth and finshed even and smooth. ( 1 ) 1 cement:6 coarse sand 82 labour charge for plastering onceilingandsoffitsof stairs upto floor twolevelinsteed of plasteringonwall. ( 1:3 ) 83 labour charge for making grooves 10 to 12mmwidex 8mm deep in plaster of the wallor in ceiling vertically or horizontally as required. 84 labour charge for makingdrip courseinsun shadeor faciaasperdirectionof engineer in charge.required for proper completion ofthe work. 85 labour charge for cement concrete flooring 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal sizelaid in onelayer neat cement ( 25 mm thickfloor ) . 86 labour charge for 20 mmthickcementplasterindado / skirting in 1:2 consistingof onepartof cement and 2 partsof aprovedcoarsesand laid inpanels, finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 including t & p etc. required forpropercompletionofthe work. 87 labour charge for painting ist coat over priming coaton steel andothermetalsurfacesup to 10 cm. widthorgirthorsmall articles not exceeding 0.10sqm in area white superior synthetic enamelspecified brushingtogiveanevenshadeand including cleaningthe surfaceofall dirt, dust and other foreignmatter sand paperingand stoping , includingtoolsandplants etc. required forpropercompletion of the work. 88 same as item 87 abovebutonnew wood surface. 89 labour charge for finishing walls with water proofing cement paint of approved make and quality new on new work with two coats to give & even shade , includingt & p etc.required for completion of the work. 90 labour charge fordistempering ( two coat ) withoil bound distemper of approvedbrand and manufacture&ofrequired shadeon undecorated wall surface to give an even shade over &includingapriming coat with cement primer of approvedbrand& manufacture afterthoroughly brushing the surface free from mortar droppings & other foreign matters& alsoincluding preparing the surfaceeven with plaster of paris or approvedsynthetic material & sand papered smooth. 91 labour charge for white washing two coat includingt&p etc.required for proper completion of the work. 92 labour charge for fixingpanesofglasswithatulorequivalent i.s.i. marked quality putty, brads and springs complete. 93 labour charge of glass strips fixing for flooring.35mm wide & 3 mm thick 94 labour charge for fixing oxidised sliding bolts16 mm dia with nuts and 250 mm long. 95 labour charge for fixing oxidised towerbolt with 9 mm dia and screw. 96 labour charge for fixing oxidiseddoorhandleswith screws 150 mm long. 97 labour charge forfixing on wall face unplasticised rigid pvc rain water pipes conforming tos:13592 type a includng jointing with seal ring conforming to is:5382 leaving 10mm gap for thermal expansion. 98 labour charge forfixing on wall face unplasticised pvc clips of approved design tounplasticised pvc rain water pipe by means of 50mmx50mmx50mm hard wood rings screwed with m.s. screws of required lengthincluding cutting brick work and fixing in cement morter 1:4 ( 1cement:4coarse sand ) and making good the wall etc.complete. 99 labour charge for fixing 125mm dia c.p. grating in place of c.i. grating over floor traps. 100 labour charge forfixing and concealing of 20mm dia 2mm thick pvc conduit pipe with isimark embossed and with pvc acessories confirming to is no.3410 for drawing wires duly sealed at jointswithorginal resin / adhesive to makethe complete piping rigid plaster with cement sand morter finished to level with matching colour includingt&p etc.requiredfor proper completion of work. 101 labour charge for fixing of hexagonal fan box with hexagonal side of approx 80mm in lengthfabricated from 16swg m.s. sheetncorporating 10mm dia m.s. round barduly bent for supporting fan hanger dully painting with red oxide and screwing arrangementwith wiring. conduit laid in the r.c.c. roof before concreting along with t&p etc. for proper completion of work....

Uttar Pradesh Jal Nigam - Uttar Pradesh

37275262 tender for invitation of rates for supply of rates for civil, electrical, sanitary and other materials for ggic shahabad, distt hardoi 1 cement ( opc / ppc ) 2 coarse sand 3 fine sand 4 brick m 150 5 tor steel 8mm dia 6 tor steel 10 mm dia 7 tor steel 12mm dia 8 tor steel 16mm dia 9 binding wire 10 stone grit 10 20mm 11 stone ballast 12 white cement 13 brick bats 14 vitrified tiles ( 600x600 ) 15 floor tiles ( 300x300 ) @.8sqm 16 wall tiles ( 300x450 ) mm 17 kota stone 25mm thick 18 granite 19 flush door ( single leaf 32mm ) 20 flush door ( double leaf 32mm ) 21 angle iron ( 40x40x5 ) 22 10mm square bar 23 z section ( f4 & f7 ) 24 hold fast 25 sliding bolt ( 250x16 ) 26 tower bolt ( 250x10 ) 27 ms handle 125mm 28 door stopper 29 obd paint ( 20 lt ) 30 exterior paint ( 20 lt ) 31 enamel paint ( black ) 20 lt 32 putty ( 40 kg ) 33 red oxide ( 20 lt ) 34 glass panes 4mm thick 35 glass strip 36 ss railing 37 chequred tile 38 collapsile shutter 39 mosquito proof jali 40 wc pan ( orissa pan ) 580x440 41 european sheet with cover & zed 42 l.l. cistern ( 10 lt ) 43 wash basin ( 550x440 ) 44 pillar cock 15mm 45 kitchen sink ( 1050x510x250 ) 46 pvc waste pipe 32mm 47 pvc waste pipe 40mm 48 beveled mirror ( 600x450 ) 49 urinal ( 580x380x350 ) 50 pvc connection pipe 15mm 51 cp brass bib cock 15mm 52 cp brass long body 15mm 53 cp brass angle valve 15mm 54 cp brass shower 15mm 55 cp brass stop cock 56 pvc pipe 90mm ( 3inch ) 57 pvc elbow 90mm 58 pvc socket 90mm 59 pvc tee 90mm 60 pvc pipe 110mm ( 4 inch ) 61 pvc elbow 110mm 62 pvc socket 110mm 63 pvc tee 110mm 64 pvc pipe 160mm ( 6 inch ) pipe 65 pvc elbow 160mm 66 pvc socket 160mm 67 pvc tee 160mm 68 cpvc 20mm pipe 69 cpvc bend 20mm 70 cpvc tee 20mm 71 cpvc socket 20mm 72 cpvc 25 pipe 73 cpvc elbow 25mm 74 cpvc tee 25mm 75 cpvc socket 25mm 76 pvc solvent 77 cpvc solvent ( 100gm ) 78 water storage tank 79 tank nipple 25mm 80 tank nipple 20mm 81 ball valve 25mm 82 gate valve 20mm 83 gate valve 25mm 84 union 25mm 85 union 20mm 86 cp brass towel rail 87 nahni trap 88 pvc p trappe 89 cp west coupling 40mm 90 cp jali 91 ms clamp 110mm 92 moduler ms box ( 3x3 ) with sheet 93 moduler ms box ( 4x4 ) with sheet 94 moduler ms box ( 5x3 ) with sheet 95 moduler ms box ( 8x3 ) with sheet 96 moduler ms box ( 9x3 ) with sheet 97 moduler ms box ( 5x5 ) with sheet 98 moduler ms box ( 8x6 ) with sheet 99 moduler ms box ( 8x8 ) with sheet 100 switch 6amp 101 socket 6amp 102 switch 16amp 103 socket 16amp 104 ceiling fan 1200mm ( havells, bajaj etc. ) 105 fan regulator 106 exhaust fan 300mm 107 led tube 20w 108 distribution board 12way 109 isolator 40amp 4p 110 isolator 63amp 4p 111 mcb 6 32amp sp 112 copper wire 0.75sqm 113 copper wire 1.00sqm 114 copper wire 1.50sqm 115 copper wire 2.50sqm 116 copper wire 4.00sqm 117 copper cable 10mm 3 fase 04 core 118 conduit pipe 25mm 119 surface junction 25mm 120 pvc bend 25mm 121 pvc saddle 25mm 122 holder 123 led bulb 9 w 124 ceiling rose 125 fan sheet 126 round sheet 127 china screw 1 inch 128 screw 1.5 inch 129 machnery screw 1 inch 130 machnery screw 1 .5 inch 131 flixble pipe 132 cut out 63 amp 133 royal plug ( 100 pcs ) 134 royal screw 1 inch 135 tape roll 136 electric pannle 137 fire fighting cylinder 9ltr co2 138 street light 40 watt 139 tubular pole 7mtr 140 excavation in foundations in ordinary soil 141 filling of carted earth 142 sand filling in plinth 143 laying cement concrete 1:4:8 144 l / c for r.c.c. work in the proportion of 1:1.5:3 ( m 20 ) in slab including necessary centering and shuttering etc.and also including , labour and tools and plants etc, required for proper completion of the works. binding wire cost being inluded in the item. 145 same above item but for beam 146 same above item but for collumn 147 brick work in super structure above plinth level up to floor two level ( up to two storeys ) 148 same as in item no. 10 but in 1:4 cement and coarse sand mortar in superstructure for wall thickness 12 cms & below brick work. 149 laying brick coba work 150 fixing isi marked flush door shutters 151 hold fast for chaukhats of doors / windows. 152 door / windows & staircase grill. 153 z section windows ( openable ) 154 angle iron door chaukhat 40*40*5 155 fixing fly proof galvanized m.s. wire gauge to windows 156 labour for mild steel or iron in plain work such as reinforced concrete 157 fixing of door, windows / ventilators chaukhats in position. 158 12 mm cement plaster including necessary centering and shuttering etc 159 12 mm cement plaster including necessary centering and shuttering etc 160 forming groove of uniform size 12x12 mm and upto 25x25 mm in plastered surface as per approved pattern using wooden battens nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing of groove complete as per specification and direction of the engineer in charge. 161 making drip coarse 162 fixing of glazed tile 163 l / c cement concrete flooring 1:2:4 ( 40mm thick ) 164 l / c cement concrete flooring 1:2:4 ( 25mm thick floor ) 165 l / c for fixing of vitrified tile 166 l / c for fixing of 25 mm thick kota stone with polish 167 l / c for fixing of granite 168 l / c for painting two coat over priming coat 169 l / c for same as above but wooden painting. 170 finishing wall with water proofing cement paint two coat. 171 l / c for distempering ( two coat ) 172 l / c for applying putty 173 l / c for fixing of glass pan 174 l / c making drain along apron 175 p / f aluminiam sheet for bathroom door 176 fixing of chequerred tile 177 cinder filling 178 making & fixing ss railing 179 fixing of collapsible shutters 180 chase cutting in brick work or r.c.c work & fixing of pvc conduct pipe repared all surface. 181 l / c wiring point for fan, light, plug etc all labour work complete 182 fixing of distribution board of all sizes including cutting of brick work providing lintel of suitable size &thickness plastering etc 183 fixing of all size factory fabricated m.s. box in existing sunk of all material, labour and t & p etc. required for proper completion of the work. 184 fixing of tubelight 185 fixing of ceiling fan 186 fixing of exhaust fan 187 fixing of swith / socket 188 fixing of w.c pan with all lbour & t&p 189 fixing of e.w.c pan with all lbour & t&p 190 fixing of wash basin, including cutting and making good the walls wherever require : 191 fixing of urinal , including cutting and making good the walls wherever require : 192 fixing of white vitereous china laboratory sink with including cutting and making good the wall walls wherever required : 193 fixing of flexible p.v.c. waste pipe for sink, wash basin & urinal basin 194 fixing / laying of pvc pipe 90mm including all fitting etc labour work complete 195 fixing / laying of pvc pipe 110 including all fitting etc labour work complete 196 fixing pvc p traps including cost of cutting & making good the walls & floors. 197 fixing of stainless steel jali ( grating ) 198 fixing / laying of cpvc pipe 20mm including all fitting etc labour work complete 199 fixing / laying of cpvc pipe 25mm including all fitting etc labour work complete 200 fixing isi marked cp brass bib cock 15mm with flange of approved quality including threading the pipe etc. for completion of work. a ) short body bib cock 201 fixing isi marked cp brass bib cock 15mm with flange of approved quality including threading the pipe etc. for completion of work. b ) long body bib cock 202 fixing isi marked c.p. brass angle valve 15 mm with flange of approved quality including threading the pipe etc. for completion of work. a ) 15 mm nominal bore 203 fixing 45 cm long unplasticised pvc connection pipe with brass unions. a ) 15 mm nominal bore 204 fixing / laying of rain water pvc pipe 110 including all fitting etc labour work complete 205 e / w in trenches 206 providing, laying p.c.c 1:4:8 207 fixing / laying of pvc pipe 160mm including all fitting etc labour work complete 208 placing on terrace ( at all floor levels ) polyethylene water storage tank isi : 12701 marked indicating the bis license no. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes 209 earthwork in excavation in foundation lift upto 1.5m and disposal of surplus excavation soil as directed with in a lead of 50 mts. 210 laying of cement concrete 1:4:8 211 brick work foundation and plinth in cement mortar 1 : 4 ( 1 cement : 4 coarse sand ) 212 reinforced cement concrete work in beams, suspended floors, roofs having slope upto 150, landings. balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement with 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size. ) 213 ms work 214 12mm cement plaster 215 cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate ) 216 making soak pit 2.5 m diameter 3.0 m deep ith 45x45 cm dry brick honey comb shaft with bricks and s.w. drain pipe 100 mm diameter 1.8 m long complete as per standerd design 217 drilling of 200 mm dia bore hole. 218 supply of 160mm dia 8kg / cm2 p v c pipe 219 supply of 160 mm dia 8 kg / cm2 slotted pvc pipe 220 lowering of 160 mm dia pvc pipe 221 supply and fixing of nylon jali around the slotted pipes complete as required 222 providing and packing of coarse sand / pea gravel around the pipe. 223 transport of boring tools other required equipements and installation at site. 224 supply of submersible pump of make ksb ( cora ) for 200 lit / min discharge at 35 meter head with control panel, support wire etc complete. 225 providing 3 core pvc insulated submersible cable. ( from pump panel to submersible pump ) 226 providing and fixing 65 mm dia. g.i. pipe complete with fittings and clamps including cutting and making good the wall etc. ( from submersible pump to ground level ) 227 providing and fixing65 mm dia. brass gate valve with ci wheel of approved quality. 228 supply and fixing of tube well accessories i.e. well cap, clips, clamps, etc. to complete the job in all respect. 229 fixing, testing and commissioning for erection and lowering of submersible pump, 65mm dia gi column pipe, 3 core submersible copper cable upto the control panel, supporting clamps, cable clips, pressure gauge, connection line and all other accessories required for the proper completion of the work. 230 testing and development of tube well....

Rural Engineering Department - Uttar Pradesh

37266524 construction of development block chatta road in village shergarh development block chatta mathura village shergarh from ramabus kiln to shernagar village. 1 construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of tables 300.1 and 300.2 as per technical specification clause 301.5 2 construction of granular sub base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavatorat omc, and compacting with smoothwheelroller to achieve thedesired density, complete as per specification contained in para 2.2, 3.6, and 3.7 of irc sp 77 2008 a on roadb in 350 mm dia gule 3 providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with threewheel 80 100 kn static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per technical specification clause 405. 4 providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with threewheel 80 100 kn static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405. 5 brick edging on both sides on the road of m 150 bricks 8cm wide and 12 cm deep laid with mud mortar including all labour and supply of bricks finished to required template & ramming the excavated earth as directed by the engineer in charge.as per ch no 20 pwd si no 765. 6 providing and applying primer coat with bitumen emulsion ( ss 1 ) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70 1.0 kg / sqm using mechanical means as per technical specification clause 502 7 providing and applying tack coat with bitumen emulsion ( rs 1 ) using emulsiondistributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with hydraulic broom as per technical specification clause 503. 8 providing, laying and rolling of open graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80 100 kn static roller capacity, finished to required level and grades to be followed by seal coat of either type a or type b or type c as per technical specification clause 508. 9 providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using type a, type b and type c as per technical specification clause 510 10 supply & laying of i shaped precast interlocking tiles of thickness 80 mm levelling and dressing of surface to required level and slope , filling joints with local sand all complete work. 11 supplying and fixing of informatory sign board i / c all charge 12 earth work excavation in foundation in ordinary soil as per si no 251 a in drain b in 350 mm dia gule 13 p / l c.c in 1:5:10 with cement , c / sand & 40 mm nominal size stone ballast in foundation as per ch no 5 s.i. no.1 d.s.r. specification no 4.1.10 14 class 150 ( non modular ) brick work in 1:4 cemen & c / sand mortar in foundation and plinthas per s.i.no.2 d.s.r.specification no.6.1.1 15 cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate ) complete 25 mm thick with 20 mm nominal size stone aggegate. 16 12 mm thick cement plaster with cement mortar in proportion of 1:4 cement&coarse sand in all comp. of work 17 r.c.c. work in 1:1.5:3 with stone grit , c / sand and cement i / c supply of material , labour and t&p etc.ch n0si n0 18 s / f of ms bars for rcc work i / c supply of material , labour and t&p etc.ch n0si n0 19 providing and laying reinforced cement concrete pipe 350mm dia np3 for culverts on first class bedding of granularmaterial in single row includingfixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets clause 1106....

Firozabad Municipal Corporation - Uttar Pradesh

37070211 tender for item rate tender for civil work. 2 earth work in cutting and cartage up to 8 k.m with all complete ( item no. 251+253 ( d ) +253 ( e ) 3 earth work in filling ordinary soil all complete. ( as per analysis ) 4 sand filling in plinth including all complete. ( item no. 255 ) 5 p / l cement concrete in 1:6:12 etc all complete. ( dsr pwd si no. 273 ) 6 p / l cement concrete in 1:5:10 etc all complete. ( dsr pwd si no. 274 ) 7 p / l cement concrete in 1:2:4 etc all complete. ( dsr pwd si no. 4.1 ) 8 p / l cement concrete in 1:1.5:3 etc all complete. ( dsr pwd si no. 4.1 ) 9 rcc work p / l in position specified grade of reinforced cemet concrete in 1:2:4 etc all complete. ( dsr / pwd si no. 5.1 ) 10 rcc work p / l in position specifled grade of reinforced cement concrete in raft foundation in 1.1.5.3 etc all complete. ( dsr / pwd si no. 5.1 ) 11 m 150 class brick work on 1:4 cement and fine sand mortor with all complete. ( dsr si.no. 6.1 ) 12 m 150 class brick work on 1:6 cement and fine sand mortor with all complete. ( dsr si.no. 6.1 ) 13 m 150 class brick work on 1:3 cement and fine sand mortor with all complete. ( dsr si.no. 6.8 ) 14 2 cm thick d.p.c with cement and approved coarse sand 1:2 etc all complete. ( dsr pwd si. no. 360 ) 15 32 mm thick supply and fixing of flush doors etc all complete. ( pwd / dsr si no. 470 ) 16 providing & fixing 1.00 mm thick decorative high pressure laminated sheet of plain wood grain in gloss etc all complete. ( pwd / dsr si no. 9.127 ) 17 mild steel and iron work of small size etc all complete. ( pwd / dsr si no. 502 ) 18 mild steel and iron work of heavy size etc all complete. ( pwd / dsr si no. 503 ) 19 providing gi barbed wire ( hot dip ) iron wire fencing in three rows including fixing it to post after stretching it including labour and tools and plants etc. required for proper completion of the work also including supply of wires ( 14x14 swg ) with 100mm barb spacing ( @11.66m per kg wt ) and excluding supply of posts. 20 steel wok in built up tubular ( round, square orrectangular hollow tubes etc. ) truses etc. including cutting. hoisting fixing in position and applying apriming coat of approved steel primer, includingwelding and bolted with special shaped washers etc.complete. ( hot finised welded type tubes. 21 mild steel or iron work in plain work etc all complete. ( as per analyisis ) 22 mild steel iron z section windows and ventilators excluding cost of glass panes of but including supply of all materials, its fabrication, nuts and bolts, holdfast, labour and t&p required for proper completion of work as per direction of engineer incharge and also including cost of handles, stays etc, in all respect at site of work. 23 mild steel iron grill & staircase railing of a approved qualitiy and drawing including supply of all materials, fabrication, labour, t&p in all respect as per direction of engineer in charge for proper completion of work at site. 24 supply and fixiing ward robe shutters made of 18 gauge ( 1.25 mm ) m.s sheets including cold rolling of required shape and including supply & fixing of approved qualitiy locks handle etc. complete including supply of all material labour and t&p spray painting etc. complete 25 providing and fixing stainless steel ( grade 304 ) etc all complete. ( pwd / dsr si no. new ) 26 providing and fixing stainless steel ( grade 202 ) etc all complete. ( pwd / dsr si no. new ) 27 providing of 1.00 mm thick with zine coating not less then 275 gm / sqm corrugated g.s sheet roofing including vertical. / curved surface fixed with ploymerr coatedetc all complete. ( pwd / dsr si no. 12.1 ) 28 providing and fixing on wall face unplasticised rigid pvc rain water pipers conforming etc all complete. ( pwd / dsr si no. 12.41 ) 29 12 mm thick plastering work on 1:3 cement and course sand mortor with all comoplete. ( pwd dsr si no. 13.9 ) 30 12 mm thick plastering work on 1:4 cement and course sand mortor with all comoplete. ( pwd dsr si no. 13.4 ) 31 12 mm thick plastering work on 1:6 cement and course sand mortor with all comoplete. ( pwd dsr si no. 13.4 ) 32 making grooves 10 to 12 mm wide x 8mm deep in plaster of the wall or in celling vertically or horizontally as required. ( pwd dsr si no. 598 ( 1 ) . 33 repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters etc all complete. with cement mortal 1:4 ( 1 cement : 4 fine sand ) ( pwd dsr si no. 14.1 ) 34 cement concrete flooring 1:2:4 ( 40 mm thick floor ) etc all complete. ( pwd dsr si no. 665 ) 35 supply & laying tack coat of bitumin @1 / 4kg per sqm with all complete 36 providing and layingdbm 50mm thick compacted with hmp &pavour finisher with all comp. 37 providing and layingsdbc 25mm thick compacted with hmp &pavour finisher with all comp. 38 providing and fixing 18 mm thick granite ( gang saw cut ) , 20 mm thick base cement morrtal 1:4etc all complete. ( pwd / dsr si no. 11.23 ) 39 providing and laying ceramic glazed floor tiles of size 300x300 mm etc all complete. ( pwd / dsr si no. 11.37 ) 40 providing and laying vitrified tiles in floor with lean concrete of 500x500 sizes ( thickness 10mm ) etc all cmomplete. ( pwd / dsr si no. 11.27a ) 41 s / f chequerred precast cement concrete tiles 22 mm thick in footpath 20 mm thick bed of cement mortar 1:4 including preparation of 50 mm thick base with concrete 1:4:8 40 mm b / b complete. ( pwd / dsr si no. 11.2 ) 42 applying priming coat over steel and other metal surface up to 10 cm etc all complete. ( pwd / dsr si no. new 641 ) 43 applying priming coat new wood surface up to 10 cm etc all complete. ( pwd / dsr si no. 19.61 ) 44 painting 1st coat over priming coat on steel and otherr metal surface up to 10 cm etc all complete ( pwd / dsr si no. 19.29 ) 45 painting 1st coat over priming coat on new wood surface up to 10 cm etc all complete ( pwd / dsr si no. 19.29 ) 46 distempering ( first coat ) with oil bound distemeper of approved brand etc all complete ( pwd / dsr si no. 649 ) 47 removing oil paint or varnish from steel and other metal surface of from wood based surface etc all complete ( pwd / dsr si no. 657 ) 48 finishing walls with water proofing cement paint of approved mak such as super snowcem durocem, robiance, guttucem, supercem quality and of required etc all complete ( pwd / dsr si no. 660 ) 49 finishing walls with sandlex matt. coat over a priming coat of water proof cement paintetc all complete ( pwd / dsr si no. new ) 50 well painting ( one coat ) with plastic emulsion pain of approved brand etc all complete. ( pwd / dsr si no. 18.58 ) 51 finishing walls with putty approved brand and etc all complete. ( pwd / dsr si no. new ) 52 finishing walls with textured exterior paint approved brand and etc all complete. ( pwd / dsr si no. new ) 53 dismeantling brick work or stone work in lime or cement etc all complete. ( pwd si no. 692 ) 54 dismeantling reinforced cement of reinforced brick worrk including stacking etc all complete. ( pwd si no. 694 ) 55 dismeantling cement concrete or brick or granolithic floors includingg etc all complete. ( pwd si no. 697 ) 56 dismeantling existing plaster including disposal of refuse as directed etc all complete. ( pwd si no. 706 ) 57 scrapping old white or colour wash includingetc all complete. ( pwd si no. 708 ) 58 dismentaliing of b.o.e soling / inter locking tiles stacking etc all complete. ( pwd si no. new ) 59 red sand stone work for wall lining etc. 30 mm thick in 1:3 etc all complet. ( pwd / dsr si no. 7.23 ) 60 construction of granular sub base ( gsb ) etc all complee. ( ase per analysis ) 61 brick soling with straight over burnt brick laid flat and dry brick edging on both side including etc all complete. sch pwd no. 762 ( b ) 62 supply and laying of i shaped precast 80 mm ( ordinary grey ) interlocking tiles etc all complete. sch pwd no. new 63 supply and laying of i shaped precast 80 mm ( ordinary coloured ) interlocking tiles etc all complete. sch pwd no. new 64 supply and laying of i shaped precast 80 mm ( rubber molded ) interlocking tiles etc all complete. sch pwd no. new 65 consolidation of stone ballast in patch repair by hand rammer including patch rectangular shape including blinding the entire consolidated surface with local earth as directed by ei / c. 66 providing and laying of hot applied thermoplastic compound 2.5mm thick including reflectrorising glass beeds @ 250gms per sqm. area, thiclness of 2.5mm is exclusive of surface applied glass beeds as per irc:35. the finish surface to be lavel, uniform and free fromstreaks and holes. composition of thermoplastic meterial shall be as per table 800 3 of clause 803 of morth including cost of all meterial, labour, t&p etc. require for proper completion of work as directionby engineer in charge. 67 constructing brick masonry manhole etc all complete. inside size 900x800 mm and 500 mm deep including c.i cover frame ( dsr si no. 19.7 ) 68 constructing brick masonry chamber for underground c.i inspection chamber and bendsetc all complete. inside dimensions 455x610 mm and 45 cm deep for single pipe : with common burnt clay f.p.s ( non modular ) brick of class designation m 150 ( dsr si no. 19.30 ) 69 providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from m.s. sheets and galvanized with zinc coating of 120 gms / sqm ( both side inclusive ) as per is : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate g.i. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to g.i. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long g.i wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall / partition with the help of rawl plugs12.5 mm thick tapered edge gypsum moisture resistant boarddsr no. 12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board 70 providing and fixing, in position concealed g.i. section for wall panelingusing board of required thickness fixed on the w profile ( 0.55 mm thick ) having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm c / c in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm. perimeter channel is fixed on thefloor and the ceiling with the nylon sleeves @ 610 mm c / c with fully threaded self tapping dry wall screws. board is fixed to the w profilewith 25 mm countersunk ribbed head screws @ 200 mm c / c., all complete as per the drawing & directions of engineer in charge, the joints of the boards are finished with specially formulated jointing compound and 48mm wide jointing tape to provide seamless finish.9.133.2.1 8 mm thick cement fibre board as peris : 14862 71 material 72 supply of m150 class bricks 73 supply of fine sand . 74 supply ofcourse sand . 75 supply ofstone grite 20mm gauge . 76 supply ofstone grite 10mm gauge . 77 supply of ordinary portland cement ( j.p, a.c.c, birla, j.k or equivalent ) opc 78 supply ofppc cement ( j.p, a.c.c, birla, j.k or equivalent ) 79 supply ofwhitecement ( j.k, or birla brand or equivalent ) 80 supply of 45 63 mm gauge stone ballast etc all complete. ( ase per analysis ) 81 supplyof 22.4 53 mm gauge stone ballast etc all complete. ( ase per analysis ) 82 supply of quary dust 83 supply of 80 mm thick c.c interlocking tiles ( gray ) with all complete. ( sor no. 8 ) 84 supply of 80 mm thick interlocking tiles ( coloured rubber moulded ) with all complete. ( pwd. 4 ( a ) 85 supply of 100 mm thick interlocking tiles ( grey ) with all complete. ( pwd. 4 ( a ) 86 supply gsb. ( as per anaylisis ) 87 head load per chainges ( 30m / cum ) 88 supply of red sand stone 89 supply of r.c.c main hole cover 90 supply of r.c.c main hole ring 91 supply of m.s iron tmt bar 8 mm dia 92 supply of m.s iron tmt bar 10 mm dia 93 supply of m.s iron tmt bar 12 mm dia 94 supply of r.c.c 900x450x100 mm ( precast ) 95 supply of r.c.c 1200x450x100 mm ( precast ) 96 supply of r.c.c 1500x450x100 mm ( precast ) 97 supply of r.c.c 600 mm dia manhole cover ( precast ) 98 supply of ballies ( 100mm ) avrage dia 99 supply of plain glass 5mm thick 100 labour 101 mistri 102 mason ( for floor & tites work ) 103 painter ( for polishing work ) 104 painter ( for painting work ) 105 mazdoor 106 gardener...

Uttar Pradesh Jal Nigam - Uttar Pradesh

36877650 tender for invitation of rates for supply of civil, electrical, sanitary, other materials and piece rated works ( labour ) 1 earth work in excavation in trenches for foundation pipes, cable etc in ordinary sol ( loam clay or sand ) inlcuding lift upto 1.5 mt. lead upto 30mt. and dressing of sides and rammings of bottom and disposal of surplus excavated earth as directed by the engineer. 2 upto 1.50 m to 3.00 m deep 3 upto 3.00 m to 4.50 m deep 4 upto 4.50 m to 6.00 m deep 5 filling of carted earth 6 laying in position cement concrete of specifiedgrade including the cost of centring and shuttering all work upto plinth level. 7 in cement concrete 1:4:8 ( 1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size ) 8 in cement concrete 1:2:4 ( 1 cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size ) 9 coarse sand ( compacted ) filling in sides of foundation & floor 10 providing and injecting chemical emulsion for pre constructional antitermite treatment and creating a chemical barrier under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete. ( plinth area of the building at ground floor only shall be measured as per i.s.6313 ( partii 1981 ) alderine emulsifiable concentrate or any other approved material such as heptrachlor or chlordane will be used. the rate of application of chemical emulsion shall be as follows : ( 1 ) treatment for masonary & foundation 5 liters per sqm. ( 2 ) back fill in immediate contact with foundation 7.5 liters / sqm ( 3 ) treatment of top surface of plinth filling 5 liters / sqm ( 4 ) treatment junction of wall and the floor 7.5 liters / sqm ( 5 ) treatment of soil along external perimeter of building 7.5 liters / sqm ( 6 ) treatment of soil under apron along external perimter 5 liters / sqm. ( as per manufacturers standard dilution ) 11 r.c.c. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 bwg binding wire and including necessary centering and shuttering etc.and also excluding supply of all materials, and including labour and tools and plants etc, required for proper completion of the works. 12 ground floor 13 first floor 14 second floor 15 as in item no. 6 above but for slabs ( using 1:1.5:3 mix concrete ) . 16 ground floor 17 first floor 18 second floor 19 as in item 6 but for thelighterbeams i.e. having spans upto 6 m. ( using 1:1.5:3 mix concrete ) 20 ground floor 21 first floor 22 second floor 23 as in item 6 abovebut inr.c.c.raft foundation and footingwithapproved stone ballast. ( using1:1.5:3mix concrete ) 24 as in item 6 above but in r.c.c. columns in 1:1.5:3 having strength not less than m 20. 25 ground floor 26 first floor 27 second floor 28 m 150 brick work in 1:6 ( one cement and six coarse sand sand of 2.25 fineness modulus ) mortar infoundation & plinth includinglabour and t & p etc & excluding supply of all materials, required for proper completion of the work. 29 m 150 brick work in 1:4 ( one cement and six coarse sand sand of 2.25 fineness modulus ) mortar infoundation & plinth includinglabour and t & p etc & excluding supply of all materials, required for proper completion of the work. 30 laying damp proof course 40mm thick with cement concrete 1:2:4 ( 1 cement : 2 coarse sand ( zone iii ) : 4 graded stone aggregate 12.5mm nominal size ) 31 applying a coat of residual petroleum bitumen of grade of vg 10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 32 same as in item no. 11 abovebutin super structure above plinth level up to floor two level ( up to two storeys ) includingnecessarycutting and moulding of brick work asrequiredand also including honeycombed brick work in thickness of wall more than 12cms. ( 1:6 cement : coarse sand ) 33 ground floor 34 first floor 35 second floor 36 same as in item no. 14 but in1:4 cement and coarse sand mortar in superstructure for wall thickness 12 cms & below brick work. 37 ground floor 38 first floor 39 second floor 40 mild steel or iron in plain work such as reinforced concrete or reinforced, brick work ( when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and excluding supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. 41 ground floor 42 first floor 43 second floor 44 15 mm cement plaster on rough side of single or half brick wall of mix : 1:3 ( 1 cement: 3 coarse sand ) 45 15 mm cement plaster in single coat on rough side of single or halfbrick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. ( 1 ) 1 cement : 6 fine sand . 46 ground floor 47 first floor 48 second floor 49 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and / or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. ( 1 ) 1 cement : 6 finesand. 50 ground floor 51 first floor 52 second floor 53 engraving lines in the plaster of outer face well vertically & horizontally to display the surface as stone facing as directed by the engineer in charge including labpur, & t & p etc. required for proper completion of the work. 54 ground floor 55 first floor 56 second floor 57 add for plaster drip course / groove in plastered surface or moulding to r.c.c. projections. 58 laying 8 to 10 mm thick ivory or light shade vitrified tiles of 600 x 600 mm size with all colours and shades, laid on 20mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) finishing with cement slurry & with pigment grouting & polishing complete including supply of all labour, t & p etc. excluding the cost of materials required for proper completion the work. 59 ground floor 60 first floor 61 second floor 62 laying 8 to 10 mm thick ivory or light shade vitrified tiles of 600 x 600 mm size with all colours and shades, laid on 20mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) finishing with cement slurry & with pigment grouting & polishing complete including supply of all labour, t & p etc. excluding the cost of materials required for proper completion the work. 63 ground floor 64 first floor 65 second floor 66 kota stone slab flooring over 20 mm ( average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand ) : 25 mm thick 67 ground floor 68 first floor 69 second floor 70 kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm ( average ) thick cement mortar 1:3 ( 1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 71 ground floor 72 first floor 73 second floor 74 fixing of 6 mm thick approved china white / coloured glazed tiles in flooring or dado laid with 1:3 cement and approved coarse sand mortar finished and jointed with white cement slurry and pigment and polishing complete includinglabour and tool sand plants & excluding supply of all materials, etc. required for proper completion of the work. 75 ground floor 76 first floor 77 second floor 78 25 mm thick cement concrete flooring 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 12.5mm nominal size and below ) by laid over base concrete finished with floating coat of neat cement ( base concrete to be paid separately ) including fixing of glass strips. ( excluding cost of glass strips ) 79 supply of flush doors commercial qualityconforming to i.s.2202 part i ( 1983 ) including fixing of wooden cleats and stoppers 80 35 mm thick 81 ( a ) single leaf 82 ( b ) double leaf 83 32 mm thick 84 ( a ) single leaf 85 extra for providing and fixing flush doors with decorative veneering instead of non decorative isi marked flush door shutters conforming to is: 2202 ( part i ) 86 fixing of flush / pvc doors including fixing of wooden / pvc cleats and stoppers and includingfixing and adjustment of hinges, bolts, locks, handle, springs. fittings to be supplied departmentally. 87 supply of factory made panel pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. m.s. frame shall have a coat of steel primers of approved make and manufacture. m.s. frame covered with 5 mm thick heat moulded pvc ‘c’ channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide pvc sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide pvc sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. top, bottom and lock rails shall be provided both side of the panel. 10 mm ( 5 mm x 2 ) thick, 20 mm wide cross pvc sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side pvc sheet to be fitted in the m.s. frame welded / sealed to the styles & rails with 7 mm ( 5 mm+2 mm ) thick x 15 mm wide pvc sheet beading on inner side, and joined together with solvent cement adhesive. an additional 5 mm thick pvc strip of 20 mm width is to be stuck on the interior side of the ‘c’ channel using pvc solvent adhesive etc. complete as per direction of engineer in charge, manufacturer’s specification & drawing. 30 mm thick plain pvc door shutters 88 mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods, gratings etc. ( when not included in an over all rates ) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. 89 m.s. hold fast for doors and windows 90 m.s. grill 91 z section winodws ( openable ) 92 m.s. angle door chaukhat 40*40*5 93 fixing of door, windows / ventilators chaukhats in position. 94 ( a ) door chaukhats 95 ( b ) window chaukhats 96 ( c ) ventilator chaukhats 97 distempering ( two coat ) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as berger, j&n, shalimar, asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. ( inside walls ) 98 ground floor 99 first floor 100 second floor 101 finishing walls with two coat of acrylic smooth exterior paint of best quality including supply of all materials labour and tool sand plants etc. required for proper completion of the work. 102 ground floor 103 first floor 104 second floor 105 finishing wall with water proof cement paint of approved make and quality on new wood with two coat to give an even shade including supply of all materials, labour, tools and plant etc. required for proper completion of the work. ( two coat ) 106 wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : two or more coats on new work supply of all materials, labour, tools and plant etc. required for proper completion of the work. ( two coat ) 107 distempering ( two coat ) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as berger, j&n, shalimar, asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth excludingcost of all materials. ( ceiling ) 108 providing & applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 109 supply of 150 mm bright finished floor stainless steel door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete. 110 supply of stainless steel sliding door bolts isi marked anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade with nuts and screws etc complete. ( a ) 250mm x 16mm . 111 supply of stainless steel towerbolts ( barrel type ) with necessary screws etc. complete 112 ( a ) 300mm x 10mm 113 ( b ) 250 mm x 10mm 114 supply of bright / matt finished stainless steel handles of approved quality & make with necessary screws etc all complete. ( a ) 125 mm 115 providing and laying cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a ) applying a slurry coat of neat cement using 2.75 kg / sqm of cement admixed with water proofing compound conforming to is. 2645 and approved by engineer in charge over the rcc slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b ) laying brick bats with mortar using broken bricks / brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 ( 1 cement : 5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge over 20 mm thick layer of cement mortar of mix 1:5 ( 1 cement :5 coarse sand ) admixed with water proofing compound conforming tois : 2645 and approved by engineer in charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c ) after two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge. d ) finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 ( 1 cement :4 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e ) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. all above operations to be done in order and as directed and specified by the engineer in charge : with average thickness of 120 mm and minimum thickness at khurra as 65 mm. 116 painting or vanishing two coat on iron work in small areas or new wood work with one coat of ready mixed priming paint and one coat of approved superior ready mixed paint of clear synthetic varnish including supply of all materials, labour, t & p etc. required for proper completion the work. paint to be used should confirm to the i.s.i. no. 103 1950. 117 same as item above but on new wood surface. 118 fixing panes of glass with equal or equivalent i.s.i. marked quality putty, brads and springs including supply of all materials, labour etc. complete. 3.80 to 4.70 mm thick 119 chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing & excluding supply of all materials complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement :4 coarse sand ) : light shade pigment using white cement. 120 filling of light cinder filling under floor of toilets & other sunken roofs. 121 labour charges for wiring points for light with 1.5 sqmm.frlsh pvc insulated single core copper condutor cable in pvc conduit pipe partly concealed in wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sqmm.frlsh pvc insulated multistrand copper conductor cable as earth continuity wire and piano type switch etc. complete in all respects. 122 same as item no. ( 1 ) but for two way light points. 123 same as item no. ( 1 ) but for fanandlight duty exhaust fan. 124 same as item no. ( 1 ) but for5amp plug point with piano type switch and socket etc. 125 addition when modular type switches etc are used in place of piono type switches etc. in various wiring points. 126 addition for light / fan points with modular type switchin place of piono type switch. 127 addition for plugpointswith modular type switchin place of piono type switch. 128 addition for exhaust fanpointswith modular type switchin place of piono type switch. 129 wiring of submains with 2 nos. 2.5 sq.mm & with 1 no. earth wire of 1.5 sq.mm fr pvc insulated 1100 v grade single core multistrand copper conductor cable in 20 mm dia heavy duty ( 2mm thick ) pvc conduit complete, including supply of all material, labourand t&p etc. required for proper completion of the work as directed by engineer i / c. 130 wiring of submain 2 number 4 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 20mm dia pvc conduit partly concealed in wall and partly laid in slab along with one number 2.5 sqmm frlsh pvc insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects. 131 wiring of submain 2 number 6 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 20mm dia pvc conduit partly concealed in wall and partly laid in slab along with one number 4 sqmm frlsh pvc insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects. 132 wiring of submain 4 number 10 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 32mm dia pvc conduitalong with two numbers 6 sqmm frlsh pvc insulated multistranded copper conductorcable as earth contunity wire etc. complete in all respects. 133 wiring of submain 4 number 16 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 40mm dia pvc conduitalong with two numbers 10 sqmm frlsh pvc insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects. 134 wiring of submain 4 number 25 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 50mm dia pvc conduitalong with two numbers 16 sqmm frlsh pvc insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects. 135 fixing and concealing of20mm dia.2mm thick pvc conduit pipe with isi mark embossed and with pvc acessories confirming to is no. 3419 for drawing wires duly sealed at joints with original resin / adhesive to make the complete piping rigid, plastering with cement sand mortar finished to level with matching colour including cost of material labour and t & p etc required for proper completion of work ( fortelephone ) 136 erection and testing of ceiling fan and regulator for room height upto 3.5mts. including supply of 3mm thick g.i. pipe 19mm dia duly painted, complete in all respects. 137 erection and testing exhaust fan on the exhisting hole with suitable size of rag bolts nuts and washers etc. complete in all respects. 138 fixing of hexagonal / round g.p. fan box of approved make made up of 1.0mm thick isi marked g.p. sheet spot weeldeed four to eight holes of 25.4 mm for pipe entry of the box. holes should be semi shuttered type with 0.5mm g.p. sheet made upper & lower cover duly screewed fitted with 300mm round zink coted m.s bar x 12mm & brand name should be embossed.fixing with wiring conduit laid in the r.c.c roof before concreting alongwith supply of all material, labour, t&p etc. required for proper completion of the work. 139 supply of ceiling fan with fan motor of a.c permanent insulation, capacitor rating conforming bee 5 star rating and is:374 / 79 and also comply with is: 1709 / 1984 with latest amendment. the rated voltage 220 / 240 volts, 50hz, 1 ph ac the fan assemble should consists of down road blades, shackle canopies etc and with double ball bearing system. bee 5 star rated 1200mm sweep 140 fixingofelectronic fan regulator ( modular ) 120 280 v. isimarked, on the existing switch board including making connetion, required material, labour t / p etc for proper completion of work to the satisfaction of engineer in charge of work. 141 fixing of led tube light with metal heavy dutybox type batten light fitting 2 x 22 watt suitable for up to 2 x 22 watt led polycarbonate tube light complete including tube etc suitable for both surface & surface complete in all respects. ( cat: aaa ) 142 fixing of led tube light with metal heavy dutybox type batten light fitting 1 x 22 watt suitable for up to 1 x 22 watt led polycarbonate tube light complete including tube etc suitable for both surface & surface complete in all respects. ( cat: aaa ) 143 fixing of recess / surface mounting round 10 to 15 watt, cut out min 125mm, height min 40mm, led down lighter having powder coated die cast aluminium housing with heat sink, diffuser / reflector and driver set, suitable for 24hr continuous operation, complete in all respect. ( cat: aaa ) 144 fixing of single led light wall bracket on matching m.d.f.e.g board base etc. complete in all respect. ( cat: aaa ) 145 fixing of water tight oblong 10 watt led bulhead luminaire with driverr set confirming to ip 65 and above protection complete in all respect. ( cat: aaa ) 146 fixing of surface / flush mounting distribution boards with additional metal door withot mcb complete in all respects. ( cat a ) 147 4 way tpn 148 6 way tpn 149 8 way tpn 150 fixing of 6amp to 32 amp ( 10 ka ) sp mcb in existing mcb, db complete with connections as required. ( cat: a ) 151 fixing and making connection of following mcbs complete in all respects as per direction and satisfaction of engineer in charge. ( cat: a ) 152 40 amp. fp mcb ( cat: a ) 153 63 amp. fp mcb ( cat: a ) 154 fixing of surface / flush mounting v tpn distribution boards with additional metal door withot mcb complete in all respects. ( cat a ) 4 way v tpn 155 fixing and making connection of following mccbs complete in all respects as per direction and satisfaction of engineer in charge. ( cat: a ) 156 100 amp. fp mccb ( cat: a ) 157 125 amp. fp mccb ( cat: a ) 158 160 amp. fp mccb ( cat: a ) 159 fixing and making connection of following mcbs complete in all respects as per direction and satisfaction of engineer in charge. ( cat: a ) 160 40 amp. tp mcb ( cat: a ) 161 63 amp. tp mcb ( cat: a ) 162 fixing of power plug with 15a / 250 v flush type switch and 5 pin 15 a / 250v flush type universal socket in suitable m.s. box of 175mmx100x50mm size with phenolic laminated bakellite sheet cover 3mm thick fixed with brass machine screws and cup washer. 163 fixing of power plug with 20a / 250 v flush type switch and 5 pin 20 a / 250v flush type universal socket in suitable m.s. box including supply of all material, labor t&p etc. required for proper completion of work. 164 fixing of single pole mcbs blanking plate complete in all respects. ( cat: a ) 165 fixing and making connection of following mccbs complete in all respects as per direction and satisfaction of engineer in charge. 63 amp. fp mccb 166 supply and burying of 600mm x 600 mmx6mm g.i. plate, vertically for earthing with its top atleast 3 mts. below ground level complete with 20mm g.i.pipe and funnel for watering and two earthing leads of no.8to10swg g.i.wire in 15mm dia g.i. pipe upto switch board ( from apron to switch board the cost of g.i. pipe and g.i. wire will be extra ) 30cm. square c.i. frame with hinged cover, masonary housing, alternate layers / of charcoal / coke and salt at least 150mm thick alround etc. complete in 167 laying of 25mmx3mm g.i. strip for earthing purpose as required complete in all respects. 168 fixing of two number 8 swg g.i. wire in 15mm dia gi pipe for earthing purpose as required complete in all respects. 169 laying of aluminium conducter, pvc insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the 170 95 sqmm3.5 core 171 70 sqmm3.5 core 172 50 sqmm3.5 core 173 35 sqmm3.5 core 174 25 sqmm3.5 core 175 10 sqmm4 core 176 fixing of brass nickle plated compression gland for pvc insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respects. the armouring of the cable shall be properly connected with the earth as per dire 177 95 sqmm3.5 core 178 70 sqmm3.5 core 179 50 sqmm3.5 core 180 35 sqmm3.5 core 181 25 sqmm3.5 core 182 10 sqmm4 core 183 fixing of palm / pin type copper tin plated cables sockets ( lugs ) to the cable leads, insuslating with tape and making of connections etc. complete in all respects as per direction of engineer incharge. 184 95 sqmm 185 70 sqmm 186 50 sqmm 187 35 sqmm 188 25 sqmm 189 16 sqmm 190 10 sqmm 191 6 sqmm 192 fixing ofmodular boxes, base & cover plate 193 fixing of following size / modules, gi box along with modular base& cover plate for modular switches in recess etc as required. 1 or 2 module ( 75mm x 75 mm ) 194 fixing ofmodular type switch / socket : 195 fixing of following modular switch / socket on theexisting modular plate & switch box including connections but excluding modular plate etc as required. 196 telephone socket outlet 197 tv antenna socket outlet 198 bell push 199 fixing of call bell / buzzer suitable single phase, 230 v etc as required. 200 laying oftelephone wire following pair 0.5 sqmm fr pvc insulated annealed copper conductor, unarmoured telephone cable in the existing surface / recessed steel / pvc conduit as required. 2 pair 201 drawing of co axial tv cable rg 6 grade, 0.7 mm solid copper conductor pe insulated, shielded with fine tinned copper braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required. 202 drawing telephone wire following pair 0.5 sqmm fr pvc insulated annealed copper conductor, unarmoured telephone cable in the existing surface / recessed steel / pvc conduit as required. 203 20 pair 204 10 pair 205 fixing of 10 pair junction boxes for floors and building with krone connectors , with connection and punching of same 206 fixing of 20 pair junction boxes for floors and building with krone connectors , with connection and punching of same 207 fixing of 50 pair junction boxes for floors and building with krone connectors , with connection and punching of same 208 laying unplastisized rigid pvc pipe conforming to is:13592 type a including jointing , cuttingand making good the walls & floors as per requirement. 150mm 209 supply of ac 230 / 250 volts, 50 hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required 300mm sweep. 210 fixing of energy meter and other accessories including connections etc. complete as required 3 phase meter 211 erection of ac 230 / 250 volts, 50 hz wall fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required450mm sweep. 212 supply of ac 230 / 250 volts, 50 hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required450mm sweep. ( at labs ) 213 fixing of wired decorative mirror light on suiatable for 9 watt led with lamp complete in all respect. 214 fixing of factory wired integral led flood light luminaires with die cast aluminium housing built with driver set suitable for 40 to 50 watt conforming to ip 65 / 66 protection complete in all respect. ( cat aaa ) 215 providing and laying water proofing treatment in sunken portion of wcs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a ) first layer of slurry of cement @ 0.488 kg / sqm mixed with water proofing cement compound @ 0.253 kg / sqm. this layer will be allowed to air cure for 4 hours. b ) second layer of slurry of cement@ 0.242 kg / sqm mixed with water proofing cement compound @ 0.126 kg / sqm.this layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. the rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. 216 fixing of stainless steel ( grade 304 ) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, i / c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, excluding the cost of materials on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer in charge. 217 providing and fixing of expansion joint system related with floor location as per drawings and direction of engineer in charge. the joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per astm b221 02. the system shall be such that it provides floor to floor / floor to wall expansion control system for various vertical localtion in load application areas thatccommodates multi directional seismic movement without stress to its components. system shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. the cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre engineered self centering arrangement that freely rotates / moves in all directions.the self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. provision of moisture barrier membrane in the joint system to have watertight joint is mandatory requirement all as per the manufactures design and as approved by engineer in charge. ( material shall confirm to astm 6063 ) floor joint of 100 mm gap 218 providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of engineer in charge. the joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper astm b221 02. the system shall be such that it provides watertight roof to roof / roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. system shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. the cover plate shall be designed of width and thickness required to satisfy movement 219 and loading requirements and secured to base members by utilizing manufacturer’s pre engineered self centering arrangement that freely rotates / moves in all directions. the self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including verticalisplacement. the joint system shall resists damage or deterioration from the impact of falling ice, exposure to uv, airborne contaminants and occasional foot traffic from maintenance personnel. provision of moisture barrier membrane in the joint system to have water tight joint is mandatory requirement. ( material shall confirm to astm 6063. ) roof joint of 100 mm gap 220 providing and fixing of expansion joint systemelated with wall joint ( internal / external ) location as per drawings and direction of engineer in charge. the joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per astm b221 02. the material shall be such that it provides an expansion joints system suitable for vertical wall to wall / wall to corner application, both new and existing construction in office buildings & complexes with no slipping down tendency amongst the components of the joint system. the joint system shall utilize light weight aluminum profiles exhibiting minimalexposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. ( material shall confirm to astm 6063 ) .wall joint of 100 mm gap 221 fixing in position stainless steel grade 304 plate 1.0 mm thick as per design for expansion joints. 200 mm wide. 222 granite stone slab 18 mm thick mirror polished quarter rounded with anti skid lines in treads of staircase full length flooring over 20 mm ( average ) thick base laid over and jointed with cement slurry mixed with pigment to match the shade of including rubbing & polishing complete with base of cement mottar 1:4 ( 1 cement : 4 coarse snad ) etc. complete excluding the cost of materials. 223 ground floor 224 first floor 225 second floor 226 fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of t iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, ocking arrangement, stoppers, handles, including applying a priming coat of approved steel primer & excluding the cost of materials. 227 fixing rolling shutters of approved make of 80 × 125 mm ( 3 × 18 gauge ) cold rolled ml lath inter lockedthrough their eintire length and joined together at the end by locks and mountedon specially designed pipe shaft with brackets and wall bearing & excluding the cost of materials. 228 40mm thick cement concrete flooring 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size and below ) by laid over base concrete finished with floating coat of neat cement ( base concrete to be paid separately ) including fixing of glass strips. ( excluding cost of glass strips ) 229 fixing glass strips in joints of floors and skirting or dado add the item of laying floors flush with floor level including supply of all materials, labour, t & p etc. required for proper completion the work. ( a ) 37 mm wide and 3.15 mm thick 230 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) and top layer 12 mm thick cement hardener consisting of mix 1:2 ( 1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size ) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturers specifications.but excluding the cost of materials etc. complete. 231 supply of 80mm thick rubber moulded cement concrete interlocking pavers block. the compressive strength of concrete pavers blocks shall not be less than 30mpa & 4.5kg / no. 232 providing and laying of 80mm thick rubber moulded cement concrete interlocking pavers block. the compressive strength of concrete pavers blocks shall not be less than 30mpa & 4.5kg / no. 233 fixing of angle iron frame 40x40x6 mm in position. 234 fencing with r.c.c. post placed at required distance, embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side only, provided with horizontal lines and two diagonals of barbed wire weighing 9.38 kg per 100 metres ( minimum ) , between the two posts fitted and fixed with g.i. staples on wooden plugs or g.i. binding wire tied to 6 mm bar nibs fixed while casting the post ( cost of r.c.c. posts, struts, g.i. barbed wire, earth work and concrete to be paid for separately ) 235 mild steel or iron work in heavy sizes such as trusses built up gates, door frames, record racks, roof work gates etc. wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. 236 providing and fixing fly proof galvanized m.s. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. with 2nd class teak wood beading 62x19 mm. 237 providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 35 mm thick shutters with isi marked m.s. pressed butt hinges bright finished of required size 238 providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. extra for providing and fixing flush doors with decorative veneering instead of non decorative isi marked flush door shutters conforming to is: 2202 ( part i ) on one side only 239 p / f curtain rods of 1.25mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with c.p. brass screws and wooden plugs etc. wherever necessary complete ( a ) 25 mm dia. 240 fixing of g.i. pipe ( 80 mm dia ) as per design & drawing as per drection of eic 241 fabrication of angle iron door chaukhat of 40*40*6 mm 242 supply of concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m ) , having 50 nos rounds per 6 metrelength, upto 3 m height of wall with existing angle iron ‘y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal r.b.t. reinforced barbed wire, stud tied with g.i. staples and g.i. clips to retain horizontal, including necessary bolts or g.i. barbed wire tied to angle iron, all complete as per direction of engineer in charge, with reinforced barbed tape ( r.b.t. ) / spring core ( 2.5mm thick ) wire of high tensile strength of 165 kg / sq.mm with tape ( 0.52 mm thick ) and weight 43.478 gm / metre. 243 fixing of concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m ) , having 50 nos rounds per 6 metrelength, upto 3 m height of wall with existing angle iron ‘y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal r.b.t. reinforced barbed wire, stud tied with g.i. staples and g.i. clips to retain horizontal, including necessary bolts or g.i. barbed wire tied to angle iron, all complete as per direction of engineer in charge, with reinforced barbed tape ( r.b.t. ) / spring core ( 2.5mm thick ) wire of high tensile strength of 165 kg / sq.mm with tape ( 0.52 mm thick ) and weight 43.478 gm / metre ( cost of materialsshall be paid separately ) 244 supply of m.s. foot rest as per standard design with 20x20mm sq bars. 245 fixing of m.s. foot rest including fixing with 20x20x10 cm. cement concrete block 1:3:6 ( 1 cement : 3 coarse sand : 6 gradded aggregate of nominal size 20mm ) as per standard design with 20x20mm sq bars. 246 supply ofc.i. tee at the inlet and outlet of septic tank. 247 fixing c.i. tee at the inlet and outlet of septic tank. 248 supply of 75mm dia vent pipes. 249 fixing of 75mm dia vent pipes. 250 supply of 75mm dia cast iron terminal guard. 251 fixing of 75mm dia cast iron terminal guard. 252 supply ofprecast rcc manhole cover and frame of required shape and approved quality. 253 m.d. 10 circular shape 500mm internal diameter 254 m.d. 2.5 circular shape 450mm internal diameter 255 fixing in position precast rcc manhole cover and frame of required shape and approved quality. 256 m.d. 10 circular shape 500mm internal diameter 257 m.d. 2.5 circular shape 450mm internal diameter 258 excavating trenches in all kinds ofsoil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. 259 up to 1.50 m depth 260 pipes 80 mm to 300 mmdiameter 261 1.50 m to 3.00 m depth 262 pipes 80 mm to 300 mmdiameter 263 opentimbering in trenches including shuttering and shoring complete. ( measurement to be taken of the face area timbered ) 264 depth not exceeding 1.5 meter 265 depth 1.5 to3.00meter 266 supply of non pressurenp 2 class ( light duty ) rcc pipe with collars etc. complete. 267 150 mm.dia. rccpipes 268 250 mm.dia. rccpipes 269 100 mm dia rcc pipes 270 laying of nonpressurenp 2 class ( light duty ) rcc pipe with collars jointed withstiffmixtureofcement mortar in the proportion of 1:2 ( 1cement : 2 finesand ) includingtestingof joints etc. complete. 271 150 mm.dia. rccpipes 272 250 mm.dia. rccpipes 273 100 mm dia rcc pipes 274 laying cement concrete 1:5:10 ( 1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size ) upto the haunches of pipes including bed concrete as per standard design 275 150 mm.dia. rccpipes 276 250 mm.dia. rccpipes 277 100 mm dia rcc pipes 278 constructing brick masonry manhole in cement mortar 1:4 ( 1 cement :4 coarse sand ) rcc top slab with 1:2:4 mix ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size ) , foundation concrete 1:4:8 mix ( 1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size ) inside plastering 12mm thick with cement mortar 1:3 ( 1 cement :3 coarse sand ) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size ) finished with a floating coat of neat cement complete as per standard design. 279 inside size 90x80cms and 45cms deep including ci cover with frame ( light duty ) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg ( weight of cover 23 kg and weight of frame 15kg ) . 280 extra for depth for manholes: 281 inside size 90x120cms and 90cms deep including ci cover with frame ( medium duty ) 455x610mm internal diamensions total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58kg ) . 282 extra for depth for manholes: 283 supply of orange colour safety footrests of minimum 6 mm thick plastic encapsulated as per is:10910 on 12 mm dia steel bar conforming to is:1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm thread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing. 284 fixing of orange colour safety footrests of minimum 6 mm thick plastic encapsulated as per is:10910 on 12 mm dia steel bar conforming to is:1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm thread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size ) complete as per design. 285 supply of double flanged ( screwed / welded ) centrifugally ( spun ) ductile iron pipes of class k 9 conforming to is 8329 100mm dia ductile iron double flanged 286 fixing & laying double flanged ( screwed / welded ) centrifugally ( spun ) ductile iron pipes of class k 9 conforming to is 8329 100mm dia ductile iron double flanged 287 supply of ci specials such as bends, reducers, collars etc. including cartage, loading, unloading, taxes, excise etc. complete. 288 fixing of ci specials such as bends, reducers, collars etc. including cartage, loading, unloading, taxes, excise etc. complete. 289 supply of push on joints to centrifugally ( spun ) cast iron pipes or ductile iron pipes including testing of joints and including the cost of rubber gasket : 100mm dia pipes 290 fixing of push on joints to centrifugally ( spun ) cast iron pipes or ductile iron pipes including testing of joints and including the cost of rubber gasket : 100mm dia pipes 291 supply ofc.i. sluice valves ( with cap ) complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) : 100mm diameter 292 fixing of c.i. sluice valves ( with cap ) complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) : 100mm diameter 293 supply of c.i. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete ( the tail pieces, tapers etc. if required will be paid separately. a ) 50mm dia 294 fixing of c.i. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete ( the tail pieces, tapers etc. if required will be paidsaperately 50mm dia 295 supply of g.i. pipes ( medium ) complete with g.i. fittings 296 80mm nominal bore. 297 65mm nominal bore. 298 50mm nominal bore. 299 40mm nominal bore. 300 32mm nominal bore. 301 25mm nominal bore. 302 20mm nominal bore. 303 15mm nominal bore. 304 laying, jointing, testing & commisioning ofg.i. pipes complete with g.i. fittings includingtenching and refilling etc. ( external work ) 305 80mm nominal bore. 306 65mm nominal bore. 307 50mm nominal bore. 308 40mm nominal bore. 309 32mm nominal bore. 310 25mm nominal bore. 311 20mm nominal bore. 312 15mm nominal bore. 313 supplying of specials for pressure pipe. 314 fixing of specials for pressure pipe. 315 supply ofgate valve ( with cap complete with bolts, nuts, rubber insertion etc. 316 80mm nominal bore. 317 65mm nominal bore. 318 50mm nominal bore. 319 40mm nominal bore. 320 32mm nominal bore. 321 25mm nominal bore. 322 fixing of gate valve ( with cap complete with bolts, nuts, rubber insertion etc. 323 80mm nominal bore. 324 65mm nominal bore. 325 50mm nominal bore. 326 40mm nominal bore. 327 32mm nominal bore. 328 25mm nominal bore. 329 constructing masonry chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 ( 1 cement : 4 coarse sand ) for sluice valve, with c.i. surface box 100mm, top diameter, 160 mm bottom diameter and 180mm deep ( inside ) with chained lid and rcc top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i / c necessary excavation, foundation concrete 1:5:10 ( 1 cement :5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design : with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 330 constructing brick masonry chamber 600 x 600x750mm insidewithf.p.s. brickwork in cement mortar 1:4 ( 1 cement : 4 coarse sand ) for sluice valve / air valve, with c. i. surface box 100 mmtop diameter, 160 mm bottom diameter and 180mm deep ( inside ) with chained lid and rcc top slabwith 1 : 2 : 4 mix ( 1 cement : 2 coarsesand : 4 gradestone aggregate 20 mm nominal size ) ; necessary excavation, foundationconcrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size ) and inside plasteringwithcement mortar 1 : 3 ( 1 cement : 3 coarsesand ) 12mmthick finished with a floatingcoatofneat cementcomplete as per standarddesign 331 supply offire brigade inlet with 63 mm dia instantaneous inlet complete with all necessary fittings and ms enclosure with glass door made of 18 / 16 swg sheet. 4 way 332 fixing, installation, testing & commissioning offire brigade inlet with 63 mm dia instantaneous inlet complete with all necessary fittings and ms enclosure with glass door made of 18 / 16 swg sheet. 4 way 333 supply of sluice valve complete with flanges, gasket, nut bolts 150 mm 334 fixing, installation, testing & commissioning of sluice valve complete with flanges, gasket, nut bolts 150 mm 335 supply of nrv complete with flanges, gasket and nut bolts. 150 mm 336 fixing, installation, testing & commissioning of nrv complete with flanges, gasket and nut bolts. 150 mm 337 supply of ms pipes conforming to is:1239 ( medium b class ) including all fittings like anchor fasteners, brick masonry supports, couplings, bends, elbows, tees and flanges etc. welded or screwed joints as required ( for riser ) 338 150 mm dia 339 100mm dia 340 fixing of ms pipes conforming to is:1239 ( medium b class ) including all fittings like anchor fasteners, brick masonry supports, couplings, bends, elbows, tees and flanges etc. welded or screwed joints as required, cutting holes and chases in brick or rcc walls and making good complete. ( for riser ) 341 150 mm dia 342 100mm dia 343 supply of manual swing type first aid fire hose reel conforming to is: 444 complete with all other necessary fixing accessories. 344 fixing, installation, testing and commissioning of manual swing type first aid fire hose reel conforming to is: 444 complete with all other necessary fixing accessories. 345 supply of fire man axe. 346 fixing of fire man axe. 347 supply of singal headed hydrant landing valve comprising of 80 mm dia flanged bend 63 mm dia, with cap and chain conforming to is:5290 ( make : newage / minimax / safex / firex ) 348 fixing, installation, testing & commissioning of singal headed hydrant landing valve comprising of 80 mm dia flanged bend 63 mm dia, with cap and chain conforming to is:5290 ( make : newage / minimax / safex / firex ) 349 supply of rrl hose pipe 63 mm dia × 15 mtr. long with gm coupling conforming to is : 636 ( make newage / jayshree / crc ) 350 fixing, installation, testing & commissioning of rrl hose pipe 63 mm dia × 15 mtr. long with gm coupling conforming to is : 636 ( make newage / jayshree / crc ) 351 supply of short branch pipe as per is:903 ( make : newage / safex / firex ) 352 fixing, installation, testing & commissioning of short branch pipe as per is:903 ( make : newage / safex / firex ) 353 supply of butterfly valve complete with flanges, gasket, nut bolts 100 mm 354 fixing, installation, testing & commissioning of butterfly valve complete with flanges, gasket, nut bolts 100 mm 355 supply of hose cabinet box of 18 swg m.s.sheet with glass to accommodate hose reel drum with ruber pipe with nozzle. 2 nos. rrl hose and 1 no. branch pipe with nozzle 356 fixing, installation, testing & commissioning of hose cabinet box of 18 swg m.s.sheet with glass to accommodate hose reel drum with ruber pipe with nozzle. 2 nos. rrl hose and 1 no. branch pipe with nozzle 357 supply of air cushion tank ( 2000x1000 ) mm. 358 fixing, installation, testing & commissioning of air cushion tank ( 2000x1000 ) mm. 359 supply of air release valve. 360 fixing, installation, testing & commissioning of air release valve. 361 supply of nrv complete with flanges, gasket and nut bolts. 100 mm 362 fixing, installation, testing & commissioning of nrv complete with flanges, gasket and nut bolts. 363 supply of pressure gauge with gauge cock 364 fixing, installation, testing & commissioning of pressure gauge with gauge cock 365 supply of electrical motor driven fire pump suitable for automatic operation consisting of following : ( terrace pump ) ( make : kirloskar / mather+platt ) ( a ) horozontally mounted, split casing, centrifugal fire pump complete for delivery of under mentioned discharge against desired mentioned head so as to ensure a minimum pressure of 30 meter at the highest and farthest outlet at the specified flow cmplete with necessary strainers, pressure gauge including bypass arrangement for periodic testing of the working of the pumpset with required length and size of medium class gi pipe and control valves for proper completion of work.the pump shall be capable of giving 150% of rated discharge at head not less than 65% of rated head.the pump shall be provided with mechanical seals. the impeller shall be enclosed type and accurately blanced dynamically.the pump casing shall be of cast iron, impeller shall be of bronze and shaft shall be of stainless steel. ( b ) squirrel cage, tefc induction motor suitable for 415 v, 3 phase having ip 55 protection and class b insulation for the above pump and flexible coupling with the pump.the motor shall b rated for continuous duty and shall have hp rating necessary to drive th pump at 150% of its rated discharge at 65% of rated head. © common bed plate of fabricated mild steel channel or cast iron type. ( d ) suitable cement concrete pump foundation and vibration clamping arrangement as required with foundation bolts, anti vibration pads, washers etc. ( e ) pressure switch for automatic operation of motor including necessary wiring upto control panel. ( f ) electrical control panel with starter, 3 pole motor protection category current limiting type mccb, indicating light, ammeter, voltmeter, selector switches, cts protective fuses, single phasing protection, dry suction cut off etc as requrd as per standard details.discharge :450 liter per minute head : 35 meter 366 installation, testing and commisioning of electrical motor driven fire pump suitable for automatic operation consisting of following : ( terrace pump ) ( make : kirloskar / mather+platt ) ( a ) horozontally mounted, split casing, centrifugal fire pump complete for delivery of under mentioned discharge against desired mentioned head so as to ensure a minimum pressure of 30 meter at the highest and farthest outlet at the specified flow cmplete with necessary strainers, pressure gauge including bypass arrangement for periodic testing of the working of the pumpset with required length and size of medium class gi pipe and control valves for proper completion of work.the pump shall be capable of giving 150% of rated discharge at head not less than 65% of rated head.the pump shall be provided with mechanical seals. the impeller shall be enclosed type and accurately blanced dynamically.the pump casing shall be of cast iron, impeller shall be of bronze and shaft shall be of stainless steel. ( b ) squirrel cage, tefc induction motor suitable for 415 v, 3 phase having ip 55 protection and class b insulation for the above pump and flexible coupling with the pump.the motor shall b rated for continuous duty and shall have hp rating necessary to drive th pump at 150% of its rated discharge at 65% of rated head. © common bed plate of fabricated mild steel channel or cast iron type. ( d ) suitable cement concrete pump foundation and vibration clamping arrangement as required with foundation bolts, anti vibration pads, washers etc. ( e ) pressure switch for automatic operation of motor including necessary wiring upto control panel. ( f ) electrical control panel with starter, 3 pole motor protection category current limiting type mccb, indicating light, ammeter, voltmeter, selector switches, cts protective fuses, single phasing protection, dry suction cut off etc as requrd as per standard details.discharge :450 liter per minute head : 35 meter 367 ( a ) horozontally mounted, split casing, centrifugal fire pump complete for delivery of under mentioned discharge against desired mentioned head so as to ensure a minimum pressure of 30 meter at the highest and farthest outlet at the specified flow cmplete with necessary strainers, pressure gauge including bypass arrangement for periodic testing of the working of the pumpset with required length and size of medium class gi pipe and control valves for proper completion of work.the pump shall be capable of giving 150% of rated discharge at head not less than 65% of rated head.the pump shall be provided with mechanical seals. the impeller shall be enclosed type and accurately blanced dynamically.the pump casing shall be of cast iron, impeller shall be of bronze and shaft shall be of stainless steel. 368 fixing & placing on terrace ( at all floor levels ) polyethylene water storage tank isi : 12701 marked indicating the bis license no. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fitting and base support for tank. [ sintex, electroplast, star, lotus or equivalent having valid isi license ] . 369 supply of halon free portable fire extinguishers as described below: 370 4.5 kg carbon dioxide extinguisher, is marked, with high pressure discharge tube, horn, control valve, cce approved cylinder 371 6 kg mono ammonium phosphate ( abc ) type cartridge operated extinguishers 372 9 kg mono ammonium phosphate ( abc ) type cartridge operated extinguishers 373 providing, fixing, testing and commissioning of 50 litres ( trolley mounted ) mechanical foam type fire extinguisher. in hp mild steel cylinders isi marked tac approved fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully charged complete in all respects including wall suspension bracket / trolley mounted and confoming to is:910 . 374 providing, fixing, testing and commissioning of co2 type fire extinguisher of capacity 22.5 kg filled with co2 gas as per is 15222 with controll discharge mechanism fitted with hose, horn & trolleyconfirms to is 2878 bearing isi mark. co2 cylinder as per is 7285 375 fixing, storing, handling, shifting, installation, testing and commissioning of halon free portable fire extinguishers as described below: 376 supply of fire related signages printed on photoluminescent u1000 aluminium sheet of 1.0 mm ( + 10% ) containing lumigen ii as base chemical, covered under uv stablized coating and of appropriate size for fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete. 377 fixing of fire related signages printed on photoluminescent u1000 aluminium sheet of 1.0 mm ( + 10% ) containing lumigen ii as base chemical, covered under uv stablized coating and of appropriate sizeincluding fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete in all respects as directed by engineer in charge. 378 supply ofci cover with frame light weight complete as perdesign size 600x600 mm 379 supply ofci cover with frame light weight complete as perdesign size 900x900 mm 380 boring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in is: 2800 ( part i ) , including collecting samples from different strata, preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, beyond 90 metre & upto 150 metre depth below ground level.drilling of 250 mm dia bore hole manually. 381 supply of unplasticized pvc medium well screen ( rms ) pipes with ribs, conforming to is: 12818, fittings & accessories etc. all complete, for all depths, as per direction of engineer in charge.150 mm nominal size dia 382 assembling, lowering and fixing in vertical position in bore well unplasticized pvc medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer in charge.150 mm nominal size dia 383 supply of stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. 384 supply of gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of engineer in charge. 385 supply of coarse sand of size range 1.5mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of engineer incharge. 386 filling, spreading & leveling coarse sand, gravels & stone boulders of size range 1.5 mm to 20 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of engineer incharge. 387 transportation charges of drilling equipment including assembly and other material as required. 388 drilling of 675 mm. dia by rotary machine 389 supply of 350 mm. dia housing pipe ( 8 mm. thick ) 390 laying of 350 mm. dia housing pipe ( 8 mm. thick ) 391 supply of 200 mm. dia blind pipe ( 8 mm. thick ) 392 laying of 200 mm. dia blind pipe ( 8 mm. thick ) 393 supply of 200 mm. dia slotted pipe ( 8 mm. thick ) 394 laying of 200 mm. dia slotted pipe ( 8 mm. thick ) 395 supply of 350 mm. dia socket 396 fixing of 350 mm. dia socket 397 supply of 200 mm. dia socket 398 fixing of 200 mm. dia socket 399 supply of 200 mm. dia bail plug 400 fixing of 200 mm. dia bail plug 401 supply of 350 mm. dia well cap 402 fixing of 350 mm. dia well cap 403 supply of 350x200 mm. dia reducer. 404 fixing of 350x200 mm. dia reducer. 405 supply of 350 mm. dia housing clamp 406 fixing of 350 mm. dia housing clamp 407 supply of pee gravel 2 mm. 4 mm. in side of bore after lower and development as required as per direction of e / i. 408 filling of pee gravel 2 mm. 4 mm. in side of bore after lower and development as required as per direction of e / i. 409 development by air compressor including transportation. 410 development by o.p. unit including transportation. 411 supply of 7.5 hp ksb make submersible pump set model bpd 302 / 4+uami 150 / 6 / 22 203 ( s / d ) suitable for tube well capable of pumping clear and cold water free from chemical and directly coupled with ksb electric moter operating of 415 volt suitable for 3 phase 50 cycle a.c. supply of following duty condition 7.5 hp 6 stage pipe.a discharge of water in lpm 860 approx size of discharge outlet in 80 mm.b total head of pump set 45 m. 412 supply of finolex or equivalent isi marked submersible copper cable of size 2x3x2.5 sq. mm. 413 fixing of finolex or equivalent isi marked submersible copper cable of size 2x3x2.5 sq. mm. 414 supply of control panel cubical type wall mounted vermin proof with internal wiring duly enameled painted and mechanically finished having l&t of qul. male switch fuse unit with hrc fuses, ameter, boltmeter, selector switch, phase indicating lamp with bulbs, instrument fuses, power capcitor single phase preventor etc. complete set with supply of jyoti or eq. air break star delta motro starter suitable for above submersible pump set. 415 supply of 80mm dia m.s. column pipe of class c both and socketed with heavy sockets in 3 / 6 meter length and one end flanged complete with interlocking arrangements. 416 lowering of 80mm dia m.s. column pipe of class c both and socketed with heavy sockets in 3 / 6 meter length and one end flanged complete with interlocking arrangements. 417 supply of 80mm dia m.s. column pipe clamps with nut, bolts, packing etc. 418 lowering of 80mm dia m.s. column pipe clamps with nut, bolts, packing etc. 419 supply of 80mm dia c.i. double flanged isi mark reflex valve of updadhya or equ. make. 420 fixing ofc.i. double flanged reflex valve 421 supply of 80mm dia c.i. double flanged isi mark sluice valve with hand wheel of upadhya or equ. make. 422 supply of 100 mm dia c.i. double flanged isi mark sluice valve with hand wheel of upadhya or equ. make. 423 supply of 150mm dia c.i. double flanged isi mark sluice valve with hand wheel of upadhya or equ. make. 424 fixing of 80 / 100 / 150 mm dia c.i. double flanged isi mark sluice valve with hand wheel 425 supply of c.i. double flanged bend of 80mm dia 426 fixing of c.i. double flanged bend of 80mm dia i / c cost of labour. 427 supply of 80mm dia c.i. tee heavy quality i / c cost of material. 428 fixing of 80mm dia c.i. tee heavy quality 429 supply of guru / fibing or equivalent make pressure gauge. 430 fixing of pressure gauge. 431 erection & commissioning of pumping plants complete along with electric wiring. 432 supply of steel wire rope of 1 / 2 size 433 fixing of steel wire rope of 1 / 2 size 434 s / b of 600mm x 600 mm x 6.0 mm g.i. plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia g.i. pipe and funnel for watering and one earthing lead on one no. 8 to 10 swg gi wite in 15mm dia g.i. pipe up to switch board ( from appron to switch board the cost of g.i. , pipe and g.i. wire will be extra ) 30 cm square c.i. frame with hinged cover masonry housing alternate layers of charcoal. coke and salt at least 150mm thick alround etc. as per directions of e / i complete in all respects as per drawing. 435 s / f of one number 8 to 6 swg g.i. wire in 15mm dia g.i. pipe for earthing, laid in ground or in wall duly concealed includingn the cost of cement, sand labour. t&p other material required for proper completion of the work as directed at site. 436 s / f of aluminium conductor pvc insulated armoured, served, sheathed cable 1100 volts grade16 sqmm x 4 core 437 fixing of aluminium conductor pvc insulated armoured, served, sheathed cable 1100 volts grade at a depth of 750mmbelow ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and on top.on surface the cable run shall be fixed on m.s. clamps etc. of suitable size or as directed by e / i complete in all respects the armoring of the cable shall be properly connected with the earth conductor by clamps etc.16 sqmm x 4 core 438 supply of 500 kva. 11 / 0.433 kv, 3phase, 50hz, dyn 11, oil type, ( uppcl approved make ) copper wound transformer with off load tap changing arrangement on hv side in steps of + / 2.50%, + / 5% & 7.5% , having cable end boxes on hv sideand 800 amp. bus trunking arrangement on lv side complete with all accessories i / c first filling of filtered dehydrated oil and confirming to is 2026 ( part 1 to part 5 ) & as per specification attached complete in all respects as required at site. 439 installation, testing and commissioning of 500 kva. 11 / 0.433 kv, 3phase, 50hz, dyn 11, oil type, ( uppcl approved make ) copper wound transformer with off load tap changing arrangement on hv side in steps of + / 2.50%, + / 5% & 7.5% , having cable end boxes on hv sideand 800 amp. bus trunking arrangement on lv side complete with all accessories i / c first filling of filtered dehydrated oil and confirming to is 2026 ( part 1 to part 5 ) & as per specification attached complete in all respects as required at site. 440 supply of 3 core standered aluminium conduktor xlpe ( cross linked polyethylene ) insulated pvc bedded, galvanised flat steel strip armoured cables confirming to i.s. 7098 ( part ii with latest amendments ) 11 kv grade 150sq. mm 3 core 441 laying of 3 core standered aluminium conduktor xlpe ( cross linked polyethylene ) insulated pvc bedded, galvanised flat steel strip armoured cables confirming to i.s. 7098 ( part ii with latest amendments ) 11 kv grade at a depht of 900 mm below ground level over a cushion of 100 mm thick fine river sand all around and protected with well burnt bricks in sides and on the top put across. thearmouring of cable shall be properly connected with earth condutor by clamps etc.150sq. mm 3 core 442 supply of 3 core 240sq.mm. xlpe aluminium conductor cable of 11 kv grage as required. 443 making indoor cable end jointing with cast resin compound, including lugs and other jointing materials, for 3 core 240sq.mm. xlpe aluminium conductor cable of 11 kv grage as required. 444 making outdoor cable end jointing with cast resin compound, including lugs and other jointing materials, for 3 core 240 sq.mm. xlpe aluminium conductor cable of 11 kv grage as required. 445 supply and burying of 40mm dia x 4.5 metres long g.i. pipe vertically for earthing having 12mm dia. holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of no. 6 to 8 swg gi wire in g.i. pipe up to appron ( and from appron to switch board the cost of g.i. wire and pipe will be extra ) upto switch board, 30cm square c.i. box with hinged cover masonary enclosure, funnel at top, alternate layers of charcoal / coke and salt at least 150mm thick alround etc. as per directions of engineer in charge complete in all respects as per drawing. 446 supply and burying of 600mm x 600 mmx6mm g.i. plate, vertically for earthing with its top atleast 3 mts. below ground level complete with 20mm g.i.pipe and funnel for watering and two earthing leads of no.8to10swg g.i.wire in 15mm diag.i. pipe upto switch board ( from apron to switch board the cost of g.i. pipe and g.i. wire will be extra ) 30cm. square c.i. frame with hinged cover, masonary housing, alternate layers / of charcoal / coke and salt at least 150mm thick alround etc. complete in all respects. 447 supply and burying of 600mm x 600mm x 3 mm copper plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia g.i pipe and funnel for watering and one earthing lead ofone no. 8swg copper wire in 15 mm dia g.i pipe up to switch board ( from appron to switch board the cost of g.i pipe and copper wire will be extra ) 30 cm square c.i frame with hinged cover masonry housingalternate layers of charcoal / coke and salt atleast 150mm thick alround etc. as per directions of engineer in charge complete in all respects. 448 supply and laying of 32mm x 6mm g.i. strip from earth electrode directly in the ground as required complete in all respects. 449 supply and laying of 32mm x 6 mm copper strip from earth electrode directly in the ground as required complete in all respects.. 450 supply and laying of 25mm x 3mm g.i. strip from earth electrode directly in the ground as required complete in all respects. 451 supply and fixing of one number 8 swg g.i wire in 15mm dia. g.i pipe for earthing laid in ground or in wall duly concealed including the cost of cement, sand, labour, t&p other material required for proper completion of the work as directed at site. 452 supply of aluminium conducter, pvc insulated armoured, served, sheeted cable 1000 bolts grade 453 300 sqmm3.5 core 454 185 sqmm3.5 core 455 150 sqmm3.5 core 456 35 sqmm3.5 core 457 25 sqmm3.5 core 458 16 sqmm4 core 459 10 sqmm4 core 460 16 sqmm2 core 461 10 sqmm2 core 462 6 sqmm2 core 463 laying of aluminium conducter, pvc insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the cable run shall be fixed on m.s. clamps etc. of suitable size. from 6 sqmm 2 core to 300 sqmm3.5 core 464 supply of brass nickle plated compression gland for pvc insulated & armoured served sheathed, underground cable including rubber ring etc. complete 465 300 sqmm3.5 core 466 185 sqmm3.5 core 467 150 sqmm3.5 core 468 35 sqmm3.5 core 469 25 sqmm3.5 core 470 16 sqmm4 core 471 10 sqmm4 core 472 16 sqmm2 core 473 10 sqmm2 core 474 6 sqmm2 core 475 fixing of brass nickle plated compression gland for pvc insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respects. the armouring of the cable shall be properly connected with the earth as per direction of eic. from 6 sqmm 2 core to 300 sqmm3.5 core 476 supply of palm / pin type copper tin plated cables sockets ( lugs ) to the cable leads, insuslating with tape 477 300 sqmm 478 185 sqmm 479 150 sqmm 480 95 sqmm 481 70 sqmm 482 35 sqmm 483 25 sqmm 484 16 sqmm 485 10 sqmm 486 6 sqmm 487 4 sqmm 488 fixing of palm / pin type copper tin plated cables sockets ( lugs ) to the cable leads, insuslating with tape and making of connections etc. complete in all respects as per direction of engineer incharge. from 4 sqmmto 300 sqmm 489 supply of 7 mtr gi octagonal pole of approved make ( top dia 70mm, bottom dia 130 mm and base plate 12 mm thik ) having 3mm thikness with single arm bracket ( 1 mtr length ) including the cost of foundation bolts, required t&p complete in all respect. 490 fixing of 7 mtr gi octagonal pole of approved make ( top dia 70mm, bottom dia 130 mm and base plate 12 mm thik ) having 3mm thikness with single arm bracket ( 1 mtr length ) on rcc foundation including the cost of foundation, foundation bolts, excavation & back filling and required t&p complete in all respect. 491 supply of led street light fitting having die cast aluminium body and diffuser with driver set suitable for 45 watt to 50 watt. confirming to ip 66 and above protection complete in all respect. 492 fixing of led street light fitting having die cast aluminium body and diffuser with driver set suitable for 45 watt to 50 watt. confirming to ip 66 and above protection complete in all respect. 493 supply of 6 amp to 32 amp dp mcb ( 10ka ) ( c curve ) for poles 494 fixing of 6 amp to 32 amp dp mcb ( 10ka ) ( c curve ) for poles 495 supply of decorative 40 to 45 watt led post top indirect light luminaire having pressure die cast aluminium body and clear glass with driver set confirming to ip 65 and above protection complete in all respect. 496 fixing of decorative 40 to 45 watt led post top indirect light luminaire having pressure die cast aluminium body and clear glass with driver set confirming to ip 65 and above protection complete in all respect. 497 supply offollowing capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contractors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn complete in all respect.25 amp spn 498 fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contractors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn complete in all respect.25 amp spn 499 supply of bakelite sheet 3 mm thick of suitable size & connector 500 fixing of bakelite sheet 3 mm thick of suitable size & connector 501 supply of m.s. pipe ( class b is : 1239 ) pole suitable for fixing 70 watt. hpsv post top including 4 pole cable junction box with 5 amp. rewireablefuse fitting and 5 amp. switch on laminated cover and m.s. box complete with water tight cover and 450x450x450mm base above ground and 2x4sqmm aluminium wire from cable box to lamp for connection including painting the pole on primer coats and necessary reducers on thetop of pole for fixing of post top lantern. 65mm dia 4m long ( 3m above ground and 1 m below ground ) . 502 fixing of m.s. pipe ( class b is : 1239 ) pole suitable for fixing 70 watt. hpsv post top including 4 pole cable junction box with 5 amp. rewireablefuse fitting and 5 amp. switch on laminated cover and m.s. box complete with water tight cover includingmasonary / pcc ( 1:3:6 ) work for erecting the pole and 450x450x450mm base above ground and 2x4sqmm aluminium wire from cable box to lamp for connection including painting the poleby an approved shade on primer coats and necessary reducers on thetop of pole for fixing of post top lantern.the work shall be complete as required up to the satisfaction of engg. in charge.65mm dia 4m long ( 3m above ground and 1 m below ground ) . 503 making of following size of cable chamber made of 230 mm thick brick work in cement mortar ( 1 cement : 6 sand ) with pcc 100 mm thick pcc base plastering of inner and outer surface with cement mortar including providing of heavy duty c.i cover complete with digging, refilling and removal of surplus soil complete as required. material cost will be paid saperately.900 mm x 900 mmx 1000 mm deep 504 supply of mv danger notice plate of 200 mm x 150 mm made of mild steel at least 2mmthick &vitreousenamelledwhiteon bothsides and withinscription insignalred colouronfront side as required. 505 supply of ht danger notice plate 250 mm x 200 mm made of mild steel at least 2mmthick &vitreousenamelledwhiteon bothsides and withinscription insignalred colouronfront side as required. 506 fixing of mv / ht danger notice plate 250 mm x 200 mm made of mild steel at least 2mmthick &vitreousenamelledwhiteon bothsides and withinscription insignalred colouronfront side as required. 507 supplying of fire buckets, round bottom made of g.i. sheet 9 11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of engineer in charge. 508 fixing of fire buckets, round bottom made of g.i. sheet 9 11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of engineer in charge. 509 supply of 1800 mm x 900 mm x 12 mm thick chequered rubber matting of tested quality 510 layingof 1800 mm x 900 mm x 12 mm thick chequered rubber matting of tested quality 511 supply of danger board fabricated from 10 gauge ms sheet as per ie rules 512 fixing of danger board fabricated from 10 gauge ms sheet as per ie rules 513 supply of shock treatment chart ( prescribed under i.e.rules ) duly framed with glass and supported from back with hard board or soft board. 514 fixing of shock treatment chart ( prescribed under i.e.rules ) duly framed with glass and supported from back with hard board or soft board with supply of all labour t & pfor proper completion of work. 515 supply of fire extinguishers, abc type 4.00 kg. capacity ( isi marked is : 15683 & tac approved ) complete with initial charges and wall bracket, 516 supply of co2 typefire extinguishers, 4.50 kg. capacity ( isi marked is : 2878 & tac approved ) complete with initial charges and wall bracket, 517 fixing of fire extinguishers, abc type 4.00 kg. & co2 type 4.5 kg. capacity complete with initial charges and wall bracket, along with supply of all labour for proper completion of work. 518 supply of water closet squatting pan ( indian type w.c. pan ) with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) conforming to is:7231, parryware / hindware / seabird / orient ( coral ) with all fittings and fixtures complete.white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests 519 fixing of water closet squatting pan ( indian type w.c. pan ) with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) conforming to is:7231, parryware / hindware / seabird / orient ( coral ) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests 520 supply of white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) , conforming to is : 7231, parryware / hindware / seabrid / orient ( coral ) with all fittings and fixtures complete.w.c. pan with isi marked black solid plastic seat and lid 521 fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) , conforming to is : 7231, parryware / hindware / seabrid / orient ( coral ) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : w.c. pan with isi marked black solid plastic seat and lid 522 supply of white vitreous china extended wall mounting water closet of size 780x370x690mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre / 6 litre ( adjustable to 4 litre / 8 litres ) , including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. 523 fixing of white vitreous china extended wall mounting water closet of size 780x370x690mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre / 6 litre ( adjustable to 4 litre / 8 litres ) , including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. 524 supply of white vitreous china wash basin with c.i. brackets painted white, 15 mm c.p. brass pillar taps, c.p. brass chain with rubber plug, 32mm c.p. brass waste of standerd pattern. 525 a ) white vitreous china wash basin size 630x450 mm with a pair of 15 mm c.p. brass pillar taps 526 b ) white vitreous china surgeon type wash basin of size 660x460 mm with single 15 mm c.p. brass pillar tapswith elbow operated levers isi marked 527 fixing of white vitreous china wash basin with c.i. brackets painted white, 15 mm c.p. brass pillar taps, c.p. brass chain with rubber plug, 32mm c.p. brass waste of standerd pattern including cutting & making good the walls wherever required. 528 a ) white vitreous china wash basin size 630x450 mm with a pair of 15 mm c.p. brass pillar taps 529 b ) white vitreous china surgeon type wash basin of size 660x460 mm with single 15 mm c.p. brass pillar tapswith elbow operated levers isi marked 530 supply of p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. 531 semi rigid pipe 532 32 mm dia 533 40 mm dia 534 fixing of p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. 535 semi rigid pipe 536 32 mm dia 537 40 mm dia 538 supply of 600x450mm bevelled edge mirror of superior glass ( of approved quality ) complete with 6mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. 539 fixing of 600x450mm bevelled edge mirror of superior glass ( of approved quality ) complete with 6mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. 540 supply of stainless steel aisi 304 ( 18 / 8 ) kitchen sink as per is : 13983 with c.i. brackets and stainless steel plug 40mm including painting of fittings and brackets, kitchen sink with drain board size 510x1040 mm bowl depth 250mm 541 fixing of stainless steel aisi 304 ( 18 / 8 ) kitchen sink as per is : 13983 with c.i. brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherrerever required.kitchen sink with drain board size 510x1040 mm bowl depth 250mm 542 supply of white vitreous china flat back half stall urinal of size 580*380*350mm with white pvc automatic flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps ( all in d.p. brass ) with waste fitting as per is : 2556, c.i. trap with outlet grating and other couplings in c.p. brass including painting of fittings. 543 range of three half stall urinals with 10 litre pv.c. automatic flushing cistern. 544 range of two half stall urinals with 5 litre pv.c. automatic flushing cistern. 545 range of single half stall urinals with 5 litre pv.c. automatic flushing cistern. 546 fixing white vitreous china flat back half stall urinal of size 580*380*350mm with white pvc automatic flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps ( all in d.p. brass ) with waste fitting as per is : 2556, c.i. trap with outlet grating and other couplings in c.p. brass including painting of fittings and cutting and making good the walls and floors wherever required: 547 range of three half stall urinals with 10 litre pv.c. automatic flushing cistern. 548 range of two half stall urinals with 5 litre pv.c. automatic flushing cistern. 549 range of single half stall urinals with 5 litre pv.c. automatic flushing cistern. 550 fixing of stone slab table rubbed, edges rounded and polished of size 75x50cm deep and 1.8cm thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 ( 1cement: 2coarse sand: 4graded stone aggregate 6mm nominal size ) as per direction of engineer in charge and finished smooth.granite stone of approved shade 551 supply of unplasticised pvc connection pipe with brass unions 552 45 cm length 553 15 mm nominal bore 554 fixing of unplasticised pvc connection pipe with brass unions 555 45 cm length 556 15 mm nominal bore 557 supply of c.p. brass bib cock of approved quality conforming to is:8931 a ) 15 mm nominal bore 558 fixing of c.p. brass bib cock of approved quality conforming to is:8931v a ) 15 mm nominal bore 559 supply of c.p. brass long body bib cock of approved quality conforming to is standards andweighing not less than 690 gms.a ) 15 mm nominal bore 560 fixing of c.p. brass long body bib cock of approved quality conforming to is standards andweighing not less than 690 gms.a ) 15 mm nominal bore 561 supply of c.p. brass angle valve for basin mixer and gyser points of approved quality conforming to is:8931a ) 15 mm nominal bore 562 fixing of c.p. brass angle valve for basin mixer and gyser points of approved quality conforming to is:8931a ) 15 mm nominal bore 563 supply of c.p. brass shower rose with 15 or 20mm inlet 150 mm diameter 564 fixing of c.p. brass shower rose with 15 or 20mm inlet150 mm diameter 565 supply of c.p. brass stop cock ( concealed ) of standard design and of approved make conforming to is:8931: 150 mm diameter 566 fixing of c.p. brass stop cock ( concealed ) of standard design and of approved make conforming to is:8931: 150 mm diameter 567 supply of ptmt bottle trap for wash basin and sink.bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms 568 fixing of ptmt bottle trap for wash basin and sink.bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms 569 supply of ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 570 fixing of ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 571 supply of ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms 572 fixing of ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms 573 supply of unplasticised pvc pipe clips of approved design to unplasticised pvc pipes by means of 50x50x50 mm hard wood plugs, screwed with ms screws 574 110mm 575 90mm 576 fixing of unplasticised pvc pipe clips of approved design to unplasticised pvc pipes by means of 50x50x50 mm hard wood plugs, screwed with ms screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand ) and making good the wall etc. complete. 577 110mm 578 90mm 579 laying of cement concrete 1:5:10 ( 1 cement : 5 coarse sand : 10 graded stone aggregate 20mm nominal size ) around p.v.c soil and waste pipe including bed concrete as per standard design ( embedded in the flooring / ground ) 580 100 / 75 mm dia 581 supply of wall face unplasticised rigid pvc rain water pipes conforming to is: 13592 type a110 mm 582 fixing on wall face unplasticised rigid pvc rain water pipes conforming to is: 13592 type a including jointing with seal ring conforming to is: 5382 leaving 10mm gap for thermal expansion. 110 mm 583 supply of wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is:13592. 584 bend 87.5 degree 585 110 mm bend 586 shoe ( plain ) 110 mm shoe 587 fixing of wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is:13592type a including jointing with seal ring conforming to is:5382 leaving 10mm gap for thermal expansion. 588 bend 87.5 degree 589 110 mm bend 590 shoe ( plain ) 110 mm shoe 591 supply of inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 592 fixing of the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 593 supply of unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with ms screws of required length. 110 mm 594 fixing of unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with ms screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand ) and making good the wall etc. complete.110 mm 595 making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size ) over pvc sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 ( 1 cement : 3 coarse sand ) and a coat of neat cement, punning, rounding the edges and making and finishing the outlet complete. 596 supply of chlorinated polyvinyl chloride ( cpvc ) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i / c fixing the pipe with clamps at 1.00m spacing. 597 20mm dia nominal outer dia pipes 598 25mm dia nominal outer dia pipes 599 32mm dia nominal outer dia pipes 600 fixing of chlorinated polyvinyl chloride ( cpvc ) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i / c fixing the pipe with clamps at 1.00m spacing.this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of engineer in charge. 601 concealed work including cutting chases and making good the walls etc. 602 20mm dia nominal outer dia pipes 603 25mm dia nominal outer dia pipes 604 32mm dia nominal outer dia pipes 605 supply of gi pipes complete with gi fittings and clamps. 606 15mm dianominal bore 607 20mm dianominal bore 608 25mm dia nominal bore 609 32mm dia nominal bore 610 40mm dia nominal bore 611 50mm dia nominal bore 612 65mm dia nominal bore 613 fixing of gi pipes complete with gi fittings and clamps, including cutting and making good walls etc. ( internal work ) . internal work exposed on wall 614 15mm dianominal bore 615 20mm dianominal bore 616 25mm dia nominal bore 617 32mm dia nominal bore 618 40mm dia nominal bore 619 50mm dia nominal bore 620 65mm dia nominal bore 621 painting of gi pipes and fittings with synthetic enamel paint over a ready mixed priming coat, both of approved quality for new work. 622 15mm dia nominal bore 623 20mm dia nominal bore 624 25mm dia nominal bore 625 32mm dia nominal bore 626 40mm dia nominal bore 627 50mm dia nominal bore 628 65mm dia nominal bore 629 supply of gi union in gi pipes 630 15mm dia nominal bore 631 20mm dia nominal bore 632 25mm dia nominal bore 633 32mm dia nominal bore 634 40mm dia nominal bore 635 50mm dia nominal bore 636 65mm dia nominal bore 637 fixing of gi union in gi pipes including cutting and threading the pipe and making long screws etc. complete ( new work ) . 638 15mm dia nominal bore 639 20mm dia nominal bore 640 25mm dia nominal bore 641 32mm dia nominal bore 642 40mm dia nominal bore 643 50mm dia nominal bore 644 65mm dia nominal bore 645 supply of gun metal gate valve with wheel of approved quality. 646 25mm dia nominal bore 647 32mm dia nominal bore 648 40mm dia nominal bore 649 50mm dia nominal bore 650 65mm dia nominal bore 651 fixing of gun metal gate valve with wheel of approved quality. 652 25mm dia nominal bore 653 32mm dia nominal bore 654 40mm dia nominal bore 655 50mm dia nominal bore 656 65mm dia nominal bore 657 supply of brass stop cock of approved quality. 658 b ) 20 mm nominal bore 659 fixing of brass stop cock of approved quality. 660 b ) 20 mm nominal bore 661 supply of terrace ( at all floor levels ) polyethylene water storage tank isi : 12701 marked indicating the bis license no. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fitting and base support for tank. [ sintex, electroplast, star, lotus or equivalent having valid isi license ] . 662 fixing & placing of terrace ( at all floor levels ) polyethylene water storage tank isi : 12701 marked indicating the bis license no. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fitting and base support for tank. [ sintex, electroplast, star, lotus or equivalent having valid isi license ] . 663 supply of glazed stoneware pipes grade a100mm dia sw pipe 664 laying and jointing glazed stoneware pipes grade a with stiff mixture of cement mortar in the proportion of 1:1 ( 1 cement : 1 fine sand ) including testing of joints etc. complete.100mm dia sw pipe 665 laying cement concrete 1:5:10 ( 1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size ) all rounds.w. pipes including bed concrete as per standard design 100mm dia sw pipe 666 supply of square mouth s.w. gully trap grade‘a’ complete with c.i. grating, water tight c.i. cover with frame of 300 x300 mm size ( inside ) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 150 x 100 mm size p type 667 fixing of square mouth s.w. gully trap grade‘a’ complete with c.i. grating, brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size ( inside ) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design150 x 100 mm size p type 668 supply of floor and wall face ringfit upvc astral ultradrain conventional system for soil and waste water pipes conforming to ( hsn code: 3917 ) type b ( i ) double socketed pipes. 669 a ) 110mm dia p.v.c. pipe 670 b ) 90mm dia p.v.c. pipe 671 fixing of floor and wall face ringfit upvc astral ultradrain conventional system for soil and waste water pipes conforming to ( hsn code: 3917 ) type b including jointing with seal ring. ( i ) double socketed pipes. 672 a ) 110mm dia p.v.c. pipe 673 b ) 90mm dia p.v.c. pipe 674 supply of upvc floor trap of self cleansing designwith cp jalicomplete in all respects. ( make : supreme / finolex / prince ) p trap type floor trap 110 x 90mm 675 fixing of upvc floor trap of self cleansing designwith cp jalicomplete in all respects. ( make : supreme / finolex / prince ) p trap type floor trap 110 x 90mm 676 supply of clean out plug ( astral ) 677 fixing of clean out plug ( astral ) 678 supply ofterminal guard. 679 a ) 110mm 680 b ) 90mm 681 fixing of terminal guard. 682 a ) 110mm 683 b ) 90mm 684 supply of wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes. 685 110mm bend 686 90 mm bend 687 110mm coupler 688 90mmcoupler 689 110x110x110 mm single tee with door 690 90x90x90 mm single tee with door 691 fixing of wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. 692 110mm bend 693 90 mm bend 694 110mm coupler 695 90mmcoupler 696 110x110x110 mm single tee with door 697 90x90x90 mm single tee with door 698 supply of 1.50 sqmm frlsh pvc insulated single core copper conductor cable 699 supply of 2.50 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable 700 supply of 4.00 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable 701 supply of 6.00 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable 702 supply of 10 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable 703 supply of 16 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable 704 supply of 25 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable 705 supply of hexagonal / round gp fan box of approved make made up of 1 mm thick isi marked gp sheet spot welded four to eight holes of 25.4 mm for pipe entry of the box duly screewed fitted with 300 mm round zink coated ms bar x 12 mm. 706 supply of ceiling fan with fan motor of ac permanent insulation, capacitor rating conforming to bee 5 star. the ratrd voltage220 / 240 volts, 50 hz, single phase, ac the fan assemble should consists of down road blades, shackle canopies with double ball bearing system – 1200 mm sweep 707 supply of electronic fan regulator ( modular ) 120 280 v isi marked 708 supply of led tube light with metal heavy duty box type batten light fitting 2x 22 watt suitable for 2x22 watt polycarbonate tube light including tube etc suitable for both surface. 709 supply of led tube light with metal heavy duty box type batten light fitting 1x 22 watt suitable for 1x22 watt polycarbonate tube light including tube etc suitable for both surface. 710 supply of recess / surface mounting round 10 to 15 watt, cut out 125 mm, height min 40 mm, led downlighter having powder coated die cast aluminium housing with heat sink, diffuser / reflector and driver set, suitable for 24 hr continuousoperation 711 supply of single led light wall bracket on matching mdfeg board base 712 water tight oblong 10 watt led bulkhead luminery with driver set conforming to ip 65 and above protection complete. 713 supply of surface / flush mounting distribution boards with additional metal door without mcb complete. ( cat a ) 714 4 way tpn 715 6 way tpn 716 8 way tpn 717 supply of 6 amp to 32 amp ( 10 ka ) sp mcb ( cat a ) 718 supply of following mcbs 719 40 amp. fp mcb ( cat a ) 720 63 amp. fp mcb ( cat a ) 721 40 amp. tp mcb ( cat a ) 722 63 amp. tp mcb ( cat a ) 723 supply of surface / flush mounting v tpn distribution boards with additional metal door without mcb complete. 4 way v tpn 724 supply of following mccbs 725 63 amp. fp mccb ( cat a ) 726 100 amp. fp mccb ( cat a ) 727 125 amp. fp mccb ( cat a ) 728 160 amp. fp mccb ( cat a ) 729 supply of power plug with 15 a / 250 v flush type switch and 5 pin 15 a / 250 v flush type universal socket in suitable ms box 175mmx100mmx50mm size ( modular ) 730 supply of single pole mcbs blanking plate complete 731 supply of gi plate for earthing size 600 mm x 600mm x 6 mm 732 supply of gi pipe 20 mm dia 733 supply of gi wire 8 to 10 swg 734 supply of ci frame ( 30 sqcm ) with hinged cover 735 supply of gi strip for earthing purpose 25 mmx 3 mm 736 supply of aluminium conductor pvc insulated armoured, served, sheeted cable 1000 volts 737 95 sqmm 3.5 core 738 70 sqmm 3.5 core 739 50 sqmm 3.5 core 740 35 sqmm 3.5 core 741 25 sqmm 3.5 core 742 10 sqmm 4 core 743 supply of brass nickle plated compression gland for pvc insulated and armoured served sheeted underground cable including rubber ring 744 95 sqmm 3.5 core 745 70 sqmm 3.5 core 746 50 sqmm 3.5 core 747 35 sqmm 3.5 core 748 25 sqmm 3.5 core 749 10 sqmm 4 core 750 supply of palm / pin type copper tin plated cable sockets ( lugs ) to the cable leads, insulating with tape 751 95 sqmm 752 70 sqmm 753 50 sqmm 754 35 sqmm 755 25 sqmm 756 16 sqmm 757 10 sqmm 758 6 sqmm 759 supply of gi box alonwith modular base and cover plate for modular switches in recess1 or 2 module ( 75 mmx75 mm ) 760 supply of telephone socket outlet ( modular ) 761 supply of tv antenna socket outlet ( modular ) 762 supply of bell push ( modular ) 763 supply of call bell / buzzer suitable single phase 230 v 764 supply of telephone cable following pair 0.5 sqmm fr pvc insulated annealed copper conductor, unarmoured 765 2 pair 766 10 pair 767 20 pair 768 supply of co axial tv cable rg 6 grade 0.7 mm solid copper conductor pe insulated sheeted with fine tinned copper braid and protected with pvc sheet 769 supply of 10 pair junction boxes for floors and building with krone connectors 770 supply of 20 pair junction boxes for floors and building with krone connectors 771 supply of 50 pair junction boxes for floors and building with krone connectors 772 supply of exhaust fan of ac 230 / 250 v, 50 hz including nuts & bolts, mounting frame and other accessories.300 mm sweep 773 supply of energy meter ( 3 phase ) and other accessories. 774 supply of wall fanof ac 230 / 250 v, 50 hz including nuts & bolts, mounting frame and other accessories. 450 mm sweep 775 supply of exhaust fan of ac 230 / 250 v, 50 hz including nuts & bolts, mounting frame and other accessories.450 mm sweep 776 supply of weired decorative mirror light suitable 9 watt led with lamp complete 777 supply of factory weired integral led flood light luminaries with die cast aluminium housing built with driver set suitable for 40 to 50 watt confoming to ip 65 / 66 protection complete. 778 supply of swiches ( modular ) 5 amp 779 supply of sockets ( modular ) 5 amp 780 supply of pvc conduit pipe 25 mm dia 781 supply of round sheet 782 supply of ceiling rose 783 supply of holder for bulbs 784 fixing of main lt panel 785 fixing of main em panel 786 fixing of sub panel 787 fixing of sub em panel 788 fixing of capacitor panel 150kvar 789 fixing of feeder piller 790 fixing of street feeder piller 791 supply of coarse sand 792 supply of cement50 kg 793 supply of brick m150 794 supply of stone grit 20 mm 795 supply of stone ballast 40 mm 796 supply of tor steel 8 mm dia 797 supply of tor steel 10 mm dia 798 supply of tor steel 12 mm dia 799 supply of tor steel 16 mm dia 800 supply of tor steel 20 mm dia 801 supply of tor steel 25 mm dia 802 supply of ms fabrication for door window and ventilator 803 supply of water proofing chemical cico tapecrete p151 804 supply of y shaped angle iron post 40x40x6 805 supply of kota stone 22 mm thick 806 supply of vitriried floor tile 8 to 10 mm thick in 600x600 mm size 807 supply of wall tile glazed / ceramic floor tiles 808 supply of ss railing 304 grade 809 supply of ms collapsible channel 810 supply of rolling shutter with ball bearing 811 supply of granite 812 supply of cinder 813 supply ofchequred tile 300x300 mm size 814 supply of ms gate made of ms hollow sections 815 supply of interlocking pavers 80 mm m30 mpa...

Archaeological Survey Of India - Uttar Pradesh

36449912 mw(c) to provision for lime concrete flooring at bridge mess and sikh square at residency, lucknow (for material) as per tender documents , supply of materials , lime (unslaked) , surkhi , coarse sand , belgiri , dry gum , gud , san , old lakhauribrick , brick ballast (25mm nominal gauge)...

Indian Army - Uttar Pradesh

36159905 bids are invited for storage facility for grocery stores mse profile sheet work , brick work , concrete flooring , bricks ballast , electric work total quantity : 4625...

Nagar Palika Parishad - Uttar Pradesh

35304483 tender for construction work of material recovery facility ( murph ) center in nagar palika parishad sardhana 1 mrf work center 2 excavationinfoundationinordinarysoil ( loam clay or sand ) including lift upto 1.50 meter and lead upto 30 meter and including filling, watering and ramming ofexcavated earthintothetrenchesorintothespace between the building and sides of foundation trenches or into the plinth and removal and disposal of sur plus earth as directed by the engineerinchargeuptoadistanceof30 meters from the foundation trenches. 3 providing and laying in cement concrete 1:4:8 ( 1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size ) and curing complete, including cost of form work, in foundation and floors. 4 sand filling in plinth under floors nicluding watering ramming consolidating and dressing complete including lead up to 50m and lift up to 1.5 and including cost of sand 5 providing and injecting chemical emulsion for preconstructional antitermite treatment and creating a chemical barrier under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete ( plinth area of the building at ground floor only shall be measured as per i.s.6313 ( partii 1981 ) alderine emulsifiable concentrate or any other approved material such as heptrachlor or chlordane will be used. the rate of application of chemical emulsion shall be as follows : ( 1 ) treatment for masonary & foundation 5 liters per sqm. ( 2 ) back fill in immediate contact with foundation 7.5 liters / sqm ( 3 ) treatment of top surface of plinth filling 5 liters / sqm ( 4 ) treatmentjunctionofwallandthefloor7.5 liters / sqm ( 5 ) treatmentofsoilalongexternal perimeterofbuilding 5 liters / sqm ( 6 ) treatment of soil under apron alongexternal perimter 5liters / sqm. ( as per manufacturers standard dilution ) 6 r.c.c. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 bwg binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than m 200.same as above but for thelighterbeams i.e. having spans upto 6 m. ( using 1:1.5:3 mix concrete ) 7 same as above but for theslab i.e. having spans upto 6 m. ( using 1:1.5:3 mix concrete ) 8 as in item 6 abovebut inr.c.c.raft foundation and footingwithapproved stone ballast. ( using1:1.5:3mix concrete ) 9 as in item 6 abovebut incolumn withapproved stone ballast. ( using1:1.5:3mix concrete ) . 10 class m 150 brick work in 1:6 cement fine sand ( of 2.25 fineness modulus ) mortar infoundation & plinth including supply of all materials, labour, tools and plants etc. required for proper completion of the work. 11 class 150 brick work in 1:6 cementand fine sandmortar in super structure including supply of all materials, labour tools and plants, etc. required for proper completetion of the work. 12 class 150 half brick work in 1:4 cementand coarse sandmortar in superstructure including supply of all materials, labour tools and plants, etc. required for proper completetion of the work. 13 p / f mild steel or iron in plain work such as reinforced concrete or reinforced, brick work ( when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. 14 12 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. ( 1 ) 1 cement : 6 fine sand. 15 15mm cement plaster in single coat of rough side of single of half brick wall for exterior plastering upto floor two level including internal rounded angles chamfers, and / or rounded angles not exceeding 80mm. in girth and finished even and smooth no. extra for mixing any additive. 1 cement : 6 fine sand 16 cement concrete flooring 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 12 20mm nominal size laid in one layer neat cement ( 40 mm thick floor ) . 17 steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.electric resistance or induction butt welded tubes 18 supply and fixing galvanized corrugated iron roofing 24 b.w.g in position including supply of all amterial, labour, tools & plants etc.required for proper complletion of the work and including wastage, 19 providing and fixing 22 b.w.g ridges, vally and gutters for iron roofing fixed with j or u bolts 10mm ( 3 / 8 ) dia with g.i. limpet and bitumen washers complete including supply of all material, labour tools & plants etc required. 20 painting two coat over priming coat ( but including cost of priming coat ) on steel and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as luxol3, hi gloss apcolite superlac, dulux specified brushing to give an even shade and including cleaning the surface of all dirt, dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work. 21 painting two coat over priming coat ( but including cost of priming coat ) on steel and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as luxol3, hi gloss apcolite superlac, dulux specified brushing to give an even shade and including cleaning the surface of all dirt, dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work. for wooden surface. 22 mild steel or iron work in heavy sizes such as trusses, builts up gates, door, frame, record racksroof work, gates etc.wrought to required form including drilling holes, rivetting or welding where necessary and also including supply of all steel. 23 providing and fixing g.i. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of engineer in charge. made of g.i. wire of dia 4 mm 24 m.s. or iron work of small sizes and sections such as holding down bolts, hold fast tie rods, gratings etc. wrought to required from including supply of steel bolts, nuts wastage etc and fixing required for proper completion of the work. angle iron door chaukhats 40*40*5 25 z section with m.s. grill 26 fixing of door, windows / ventilators chaukhats in position. ( a ) door chaukhats 27 ( b ) window chaukhats 28 providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes 29 supply and fixing of 3.8cm ( 1.1 / 2 ) thick country wood door fully panneled shutter including supply and fixing of wooden cleats stops and including fixing & adjustment of hinges, bolt, locks handles spring or other fittings. ( a ) 38 mm thick including isi marked stainless steel butt hinges with necessary screws single leaf 30 providing and fixing aluminium sliding door bolts, isi marked anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) , transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm 31 providing and fixing aluminium tower bolts, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : ( a ) 250 mm x 10mm 32 providing and fixing aluminium handles, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125mm 33 finishingwallswithwater proof cement paint of approved make and quality on new work with two coat to given an even shed including supply of all materials, labour, tools & plant etc.required for proper completion of the work 34 supply andfixingof 7.5cm 6kg / per sq.cm internal dia ac / rain water down pipe everest or charminar make complete with bands with door at top plain at bottom and grating and including supply of necessary ms clamps 2.5cmx3mm fixed to wall with and including all complete of all work5 mm diameter 35 add internal electrification works 36 add extra for 6 water taps in washing unit 37 excavationinfoundationinordinarysoil ( loam clay or sand ) including lift upto 1.50 meter and lead upto 30 meter and including filling, watering and ramming ofexcavated earthintothetrenchesorintothespace between the building and sides of foundation trenches or into the plinth and removal and disposal of sur plus earth as directed by the engineerinchargeuptoadistanceof30 meters from the foundation trenches. 38 providing and laying in cement concrete 1:4:8 ( 1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size ) and curing complete, including cost of form work, in foundation and floors. 39 class m 150 brick work in 1:6 cement fine sand ( of 2.25 fineness modulus ) mortar infoundation & plinth including supply of all materials, labour, tools and plants etc. required for proper completion of the work. 40 providing and fixing in position chain linked steel wire fabric made of 4mm dia g.i wire of required width in mesh to concrete / wooden / angle iron posts including securing and screwing with 2mm dia g.i wire, g.i staples, g.i.u nails or steel pins etc. complete 41 mild steel or iron work in heavy sizesangle iron post and strut of required size including bottom to be split and bent at right angle in opposite direction for required length and drilling holes upto 10mm dia. as per requirement including priming coat with red oxide zinc chromate primer and placing the post / strut in cement concrete block. 42 providing and laying nominal mix plain cement concrete with crushed stone aggregate using concrete mixer in all works1:2:4 ( 1 cement:2 coarse sand 4graded stone aggregate 20mm nominal size ) 43 12mm thick cement plaster of mix: in cement mortar 1:6 ( 1 cement :6 fine sand ) 44 finishingwallswithwater proof cement paint of approved make and quality on new work with two coat to given an even shed including supply of all materials, labour, tools & plant etc.required for proper completion of the work 45 excavationinfoundationinordinarysoil ( loam clay or sand ) including lift upto 1.50 meter and lead upto 30 meter and including filling, watering and ramming ofexcavated earthintothetrenchesorintothespace between the building and sides of foundation trenches or into the plinth and removal and disposal of sur plus earth as directed by the engineerinchargeuptoadistanceof30 meters from the foundation trenches. 46 providing and laying in cement concrete 1:4:8 ( 1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size ) and curing complete, including cost of form work, in foundation and floors. 47 providing and injecting chemical emulsion for preconstructional antitermite treatment and creating a chemical barrier under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete ( plinth area of the building at ground floor only shall be measured as per i.s.6313 ( partii 1981 ) alderine emulsifiable concentrate or any other approved material such as heptrachlor or chlordane will be used. the rate of application of chemical emulsion shall be as follows : ( 1 ) treatment for masonary & foundation 5 liters per sqm. ( 2 ) back fill in immediate contact with foundation 7.5 liters / sqm ( 3 ) treatment of top surface of plinth filling 5 liters / sqm ( 4 ) treatmentjunctionofwallandthefloor7.5 liters / sqm ( 5 ) treatmentofsoilalongexternal perimeterofbuilding 5 liters / sqm ( 6 ) treatment of soil under apron alongexternal perimter 5liters / sqm. ( as per manufacturers standard dilution ) 48 r.c.c. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 bwg binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than m 200. 49 r.c.c. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 bwg binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than m 200. 50 class m 150 brick work in 1:6 cement fine sand ( of 2.25 fineness modulus ) mortar infoundation & plinth including supply of all materials, labour, tools and plants etc. required for proper completion of the work. 51 providing and laying damp proof course 25mm thick with cement concrete 1:2:4 ( 1 cement : 2 coarse sand ( zone iii ) : 4 graded stone aggregate 12.5mm nominal size ) 52 providing & applying a coat of residual petroleum bitumen of grade of vg 10 of approved quality using 1kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 53 same as in item no. 11 abovebutin super structure above plinth level up to floor two level ( up to two storeys ) includingnecessarycutting and moulding of brick work asrequiredand also including honeycombed brick work in thickness of wall more than 12cms. ( 1:6 cement : coarse sand ) 54 same as in item no. 9 but in1:4 cement and coarse sand mortar in superstructure for wall thickness 12 cms & below brick work. 55 p / f mild steel or iron in plain work such as reinforced concrete or reinforced, brick work ( when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. 56 15mm thick plaster with cement mortar in proportion of 1:4 cement & coarse sand of 2.25 f.m. 57 12 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. ( 1 ) 1 cement : 6 fine sand 58 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and / or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. ( 1 ) 1 cement : 6 finesand 59 supply and fixinmg 6 to 8mm thick ivory or light shades vitrified floor tiles size 600x600 mm ( thickness to be specified by themanufacturer ) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar1:4 ( 1cement:4coarsesand ) , jointing with grey cement slurry @ 3.3kg / sqm including pointing the joints with white cementandmatchingpigmentetc., complete.. ground floor 60 providing and fixing 6mm thick china glazed tiles of first quality in skirting or dado laid over 12 mm thick bedofcementmortar1:3 ( 1cement:3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in whitecementmixedwithpigmentof matching shade complete. ground floor 61 cement concrete flooring 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 12 20mm nominal size laid in one layer neat cement ( 25 mm thick floor ) . 62 supply and fixing of 3.8cm ( 1.1 / 2 ) thick country wood door fully panneled shutter including supply and fixing of wooden cleats stops and including fixing & adjustment of hinges, bolt, locks handles spring or other fittings. 63 m.s. or iron work of small sizes and sections such as holding down bolts, hold fast tie rods, gratings etc. wrought to required from including supply of steel bolts, nuts wastage etc and fixing required for proper completion of the work. providing & fixing of hold fast for chaukhatsof doors and windows. 64 providing & fixing of door / windows grill. 65 z section steel windows ( openable ) 66 angle iron door chaukhats 40*40*5 67 fixing of door, windows / ventilators chaukhats in position. ( a ) door chaukhats 68 ( c ) ventilator chaukhats 69 white washing two coat including supply of all materials, labour and t & p etc. required for proper completion of the work. ground floor 70 finishing wall with water proof cement paint of approved make and quality on new work with three coats to give an even shade including supply of all materials, labour and t & p etc. required for proper completion the work. two coat ground floor 71 white washing two coat including supply of all materials, labour and t & p etc. required for proper completion of the work. 72 providing & fixing stainless steel sliding door bolts isi marked anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade with nuts and screws etc complete. ( a ) 250mm x 16mm . 73 providing and fixing stainless steel handles with screws etc. complete ( a ) 125 mm 74 ( c ) after two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to is : 2645 and approved by engineerin charge. 75 providing & fixing stainless steel sliding door bolts isi marked anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade with nuts and screws etc complete. ( a ) 250mm x 16mm . 76 painting two coat over priming coat ( but including cost of priming coat ) on steel and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as luxol3, hi gloss apcolite superlac, dulux specified brushing to give an even shade and including cleaning the surface of all dirt, dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work. 77 same as item 27 above but on new wood surface. 78 providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes 79 cost for internal w / s and sanitatio 80 cost for soak pit 81 cost for internal electrification 82 providing, laying, spreading 22.5 53 mmstone ballast with fine sand including supply of all material, labour and t&p etc.required for proper completion of work for interlocking tiles pathway 83 providing and laying cement concrete 1:4:8 ( 1cement :4 coarse sand :8graded stone ballast 40 mm. nominal size ) including supply of all materials, labour and t&p etc. required for proper completion of the work and curing complete, also including cost of formwork in foundation. 84 supply & fixing 80mm thick precast cement concrete ( colour tileswith isi mark ) i shape interlocking paver block a with top layer of minimum 8 mm thickness having plan dimention 200x ( 160+120mm ) of op cement smooth high gloss finidh skid reditant manufactured from rubber moulds through vibro compression machanism.the compressive strength of concrete paver block shall not be less than 40mp ( m 30 ) and wight 4.5kg per no confirming to is 15658 2006 with a 4cm thick layer of fine sand including cost of material, labour, t & p taxes etc required for proper completion of the work as directed by engineer in charge 85 external w / s arrangement, t.w. boring of 150mm dia with 100mm dia p.v.c. pipe assembly, 1.5 h.p. submersible pump including supply of all accessories starter, panel etc. & pipe arrangement etc. 100mm dia pvc pipe of isi mark [ 14 kg pressure ] 86 p / f 2 pvc pipe 87 nylon mesh for filter 88 plastic dori 89 solvent dori 90 4 end cap 91 4 submersible cap 92 2 ms clamp ( heavy ) 93 2 gl elbow. 94 2*6 gi nipple 95 1.5 hp 9 stage submersible pump of isi mark with automatic pannel 96 2.5 sqm. submersible cable. 97 drilling charges for 6 dia tubewell. 98 pea gravel 99 2 ms socket. 100 cartage of material upto site. 101 mild steel or iron work in heavy sizes such as trusses built up gates, door frames, record racks, roof work gates etc. wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. 102 painting one coat over priming coat ( but including cost of priming coat ) on steel and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as luxol3, hi gloss apcolite superlac, dulux specified brushing to give an even shade and including cleaning the surface of all dirt, dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work. 103 preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re rolling the sub grade and disposal of surplus earth with lead upto 50 metres. 104 providing and laying of 22.4 53 mm stone layer in base of c. road complete item 105 providing and laying c.c. pavement of mix m 20 with ready mixed concrete in 1:1.5:3from batching plant. the ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of engineer incharge. ( the panel shuttering work shall be paid for separately ) . ( note: cement content considered in this item is @ 330 kg / cum. excess / less cement used as per design mix is payable / recoverable separately ) . 106 add cost of external electric connection 107 18% gst 108 add 2% for contengencies...

North Central Railway - Uttar Pradesh

34923652 1 ) cmlr jhansi: industrial flooring in ward mlr for storing stock items cmlr workshop, jhansi. 2 ) jhs ( workshop ) :improvement of existing godowns by providing galvanized sheet over roof , concrete, flooring and storage system in gsd jhansi. 3 ) jhansi ( workshop ) :construction of new additional two bay adjoining with present ntws shed. 4 ) construction of road for pocket yard and nagra siding cutting yard inside wagon repair workshop jhansi....

Urban Development Department - Uttar Pradesh

34633351 bids are invited for open gym equipments horse rider , chest press , triple twister , air walker , cross walker , surf board , arm wheel , shoulder wheel , rowing machine , pull chair , abdominal board , leg press , bicycle , waist and back massager , chinup and dipping , elliptical cross trainer , earth work , cement concrete , brick work in , bed of dry brick aggregate of , local sand filling under floor , salt free earth , cement concrete flooring total quantity : 59324...

Cane Development and Sugar Industry - Uttar Pradesh

34361390 tender for farm machinery work in the pilibhit campus of cooperative sugarcane development society 1 excavation of foundation in ordinary soil ( loam clay or sand ) including lift upto 1.50 meter and lead upto 30 meter and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of foundation trenches or into the plinth and removal and disposal of sur plus earth as directed by the engineer in charge up to a distance of 30 meters from the foundation trenches. 2 filling of carted earth. 3 sand filling in plinth under floors including watering, ramming, consolidating and dressing complete including lead up to 50m and lift up to 1.5m and including cost of sand. 4 providing and laying in cement concrete 1:4:8 ( 1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size ) and curing complete, including cost of form work, in foundation and floors. 5 as in item 6 but for thelighterbeams i.e. having spans upto 6 m. ( using 1:1.5:3 mix concrete ) ground floor 6 as in item 6 abovebut inr.c.c.raft foundation and footingwithapproved stone ballast. ( using1:1.5:3mix concrete ) ( upto plinth ) 7 as in item 6 above but in r.c.c. columns in 1:1.5:3 having strength not less than m 20. ground floor 8 same as in item no. 10 abovebutin super structure above plinth level up to floor two level ( up to two storeys ) includingnecessarycutting and moulding of brick work asrequiredand also including honeycombed brick work in thickness of wall more than 12cms. ground floor 9 p / f mild steel or iron in plain work such as reinforced concrete or reinforced, brick work ( when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. ground floor 10 providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete.fixed to steel windows by welding 11 15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 ( 1 cement: 4 coarse sand ) 12 12 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. ( 1 ) 1 cement : 6 fine sandground floor 13 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and / or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. ( 1 ) 1 cement : 6 fine sand ground floor 14 cement concrete flooring 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 12 20mm nominal size laid in one layer neat cement ( 40 mm thick floor ) . 15 cement plaster skirting up to 30 cm height, with cement mortar 1:3 ( 1 cement : 3 coarse sand ) , finished with a floating coat of neat cement.18 mm thick ground floor 16 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade :new work ( two or more coats applied @ 1.43 ltr / 10sqm over and including priming coat of exterior primerapplied @ 2.20 kg / 10 sqm ) ground floor 17 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 18 distempering ( two coat ) with oil bound distemper of approved brand and manufacture & of required shade on ceiling to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as berger, j & n, shalimar, asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters including cost of all labour & materials. ground floor 19 applying putty base 20 mild steel or iron work in heavy sizes such astrusses, builtup gate, roof work etc., wrought to required formincluding cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.electric resistance or induction butt welded tubes 21 providing and fixing precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm ( + 0.05 % ) total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineerin charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55 mm ) with epdm seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 22 painting ist coat over priming coat ( butexcluding cost of priming coat ) on steelandothermetalsurfacesup to 10 cm. widthorgirthorsmall articles not exceeding 0.10sqm in area white superior synthetic enamel such as luxol3, hi glossapcolitesuperlac, dulux specifiedbrushingtogiveanevenshadeandincluding cleaningthe surfaceofalldirt, dust and other foreignmatter sandpaperingand stopingincluding cost ofall materials, labour toolsandplantsetc. required forpropercompletion ofthe work....

Rural Engineering Department - Uttar Pradesh

34067057 tender for pt. deendayal upadhyay r.m. inter college tenduakaji laboratory ( chemistry science ) development block dostpur 1 cleaning jungle i / c uprooting of rank vegitation, grass brush wood, tree and sapling of girth up to 30 cm measured at a height of 1 m above ground level and remoovel of rubbish upto distance of 50 mas per sl no 2.31 2 earth work in surface excavation not exceeding 0.30m and above in depth but exceeding 1.50 m in width as well as 10 sqm on plan i / c getting out and disposal of excavated earth upto 50m and lift upto 1.50m as directed by engineer in charge 2.1.1 all kind of soil as per si no 2.6.1 3 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto the plinth level 1:6:12 ( 1 cement: 6 c sand : 12 brick aggregate 40 mm nominal size ) as per sl no 273 4 brick work with common burnt clay ( non modular ) bricks of class 150 in foundation and plinth in cement mortar 1;6same as per sl no 6.1.2 5 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto the plinth level 1:1.5:3 ( 1 cement: 1.5 c sand : 3 stone aggregate 20 mm nominal size ) as per sl no 4.1.2 6 centering and shuttering i / c strulting, propping etc. and removal of form work for column, piers , aboutments, post, and struts same as per sl no 5.9.5 7 e / w in cutting and filling in mix soil i / c a cortage of 1 km distance including all complete of work. 8 brick work with common burnt clay ( non modular ) bricks of class 150 super structure in cement mortar 1;6same as per sl no 6.4.2& 6.5 9 brick work with common burnt clay ( non modular ) bricks of class 150 super structure in cement mortar 1:4same as per sl no 6.4.1& 6.5 10 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto the plinth level 1:1.5:3 ( 1 cement: 1.5 c sand : 3 stone aggregate 20 mm nominal size ) as per sl no 4.2.2 11 centering and shuttering i / c strulting, propping etc. and removal of form work for column, piers , aboutments, post, and struts same as per sl no 5.9.20 12 m.s. of iron workin plain work such as reinforcement concrete / brick work ( when not included in over all rates ) wrought to required shapes as necessary including bending for proper completion of the work and including supply of steel, its westage and hooks and authoriesed over lapping shall be measered ….as per rate analysis based on sail latest rate 13 steel work welded in built up sections / framed work, i / c cutting fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar , ladder, railings, brackets grates and similar works same as per sl no 10.25.2 14 providing & fixing 1 mm thk ms sheet doors &windows with frame of 40x40x6mm angle iron, and 3 mm gusset plates at the junctions and corners all necessary fittings complete i / c applying a priming coat of approved steel primer same as per sl no 10.5.1 15 providing and fixing isi marked flush door shutters confurming to is 2202 ( part 1 ) non decorative type core of block board construction i / c all etc. completed 30 mm thk i / c isi marked stainless steel but hingh with neccessorysl no 9.21.2 & 9.26 16 providing & fixing isi marked oxidised ms handle conferming to isi 4992 with neccessory screws etc completed 17 providing & fixing isi marked bright finish tower bolt with neccessory screws etc completed 18 12mm thick cement plaster of mix 1:6 cementc sand i / c al etc. required for proper comletion of work as per si no.13.4.2 19 cement concrete flooring in 1:2:4 ( 1 cement: 2 c sand : 4graded stone aggregate 20 mmsize ) finish with a floating coat of neat cement i / c cement slurry but excluding the cost of noising of steps etc completed 40 mm thk with 20 mm nominal size of stone aggregate as per sl no 11.3.1 20 fixing panesof glass2.8to 3.7mm with aual or equivalent isi marked quality putty brads and springs complete. 21 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto the plinth level 1:4:8 ( 1 cement: 4 c sand : 8 brick aggregate 40 mm nominal size ) as per sl no 4.1.8 22 finishing wall with premium acrylic smooth exterior paint with silicon additives or required shade, new work two or more coat applied @ 1.67 ltr / 10 sqm over and priming coat….as per pwd specification of ayodhya scheduled item no.13.46.1 23 paint or venishing new iron work or new wood work withone coat priming and two coat of approved paint i / c all material labour t&p ….as per pwd specification 15.1.1 scheduled item no. 641 & 642 24 providing and fixing of 110 mm outer dia . pvc pipe 6 kg / cm2 pressure i / c all etc completed 25 providing and layingrectified glazed ceramic floor tiles of size 300x300 mm or more ( thickness to specified by the manufacturar ) of ist quality conforming to is 15622 of the approved brand and manufacture in all colour and shade laidon 20mm thk cement mortar 1:4 joint with grey cement slurry @ 3.3 kg / sqm i / c grouting the joint with white cement with matching pigments etc. completed size of tile 600x600 mm same as per sl no 11.39 26 wiring point for light in pvc conduit with 1.5 sqm. fr pvc insulated multistarand copper conductor cable as earth wire drawn inside the conduit. si no. 131 © 27 wiring point for fan / fresh air fan in pvc conduit with 1.5 sqm. fr pvc insulated multistarand copper conductor cable as earth wire drawn inside the conduit. si no. 133 © 28 s / f of power plug with 15 a / 250 v flush type switch & 5 pin 15 a / 250 v flush type universal socket. si no. 1139 29 s / f hexagonal fan box. as si no. 1149. 30 s / f of switch box of 16 swg dully painted with red oxide primer and flushed with wall.1203 31 s / f of batten / angle holder complete. si no. 405 32 s / f suface / flush mounting 4 ways spn distribution board ( legrand lexic ) with additional metal door with out mcb complete in all respect. si no. 1022 b 33 s / f of 6 amp to 32 amp spmcb ( 10 ka ) ( legrand lexic ) si no 1002 ( a ) . 34 provide and fixing of cpvc pipe having thermal suitability for hot and cold water supply, i / c all cpvc plain & brass threaded fitting i / c the fixing of pipe with clamp at 1.0 m spacing this i / c the joint of pipes & fitting one steps cpvc solvent cement and testing of joints complete with direction of engineer in charge external work 15 mm nominal outer dia pipes 35 provide and fixing of cpvc pipe having thermal suitability for hot and cold water supply, i / c all cpvc plain & brass threaded fitting i / c the fixing of pipe with clamp at 1.0 m spacing this i / c the joint of pipes & fitting one steps cpvc solvent cement and testing of joints complete with direction of engineer in charge external work 20 mm nominal outer dia pipes 36 provide and fixing of cpvc pipe having thermal suitability for hot and cold water supply, i / c all cpvc plain & brass threaded fitting i / c the fixing of pipe with clamp at 1.0 m spacing this i / c the joint of pipes & fitting one steps cpvc solvent cement and testing of joints complete with cost of cutting chases and making good the same direction of engineer in charge internal work15 mm nominal outer dia pipes 37 provide and fixing of cpvc pipe having thermal suitability for hot and cold water supply, i / c all cpvc plain & brass threaded fitting i / c the fixing of pipe with clamp at 1.0 m spacing this i / c the joint of pipes & fitting one steps cpvc solvent cement and testing of joints complete with cost of cutting chases and making good the same direction of engineer in charge internal work20 mm nominal outer dia pipes 38 providing & fixing of brass bib cock of approved quality 15 mm nominal bore 39 providing & fixing of brass stop cock of approved quality 15 mm nominal bore 40 provide and fixing wash basin with ci bracket 15 mm cp brass pillar traps32 mm cp brass waste of standard pattern i / c painting of fitting and brackets cutting and making good the walls whereever required white vitreous china wash hand basin size 630x450 mm with asingle 15 mm cp brass piller tap....

Rural Engineering Department - Uttar Pradesh

34066990 tender for government inter college maharajganj laboratory ( biology science ) development block dubeypur 1 cleaning jungle i / c uprooting of rank vegitation, grass brush wood, tree and sapling of girth up to 30 cm measured at a height of 1 m above ground level and remoovel of rubbish upto distance of 50 mas per sl no 2.31 2 earth work in surface excavation not exceeding 0.30m and above in depth but exceeding 1.50 m in width as well as 10 sqm on plan i / c getting out and disposal of excavated earth upto 50m and lift upto 1.50m as directed by engineer in charge 2.1.1 all kind of soil as per si no 2.6.1 3 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto the plinth level 1:6:12 ( 1 cement: 6 c sand : 12 brick aggregate 40 mm nominal size ) as per sl no 273 4 brick work with common burnt clay ( non modular ) bricks of class 150 in foundation and plinth in cement mortar 1;6same as per sl no 6.1.2 5 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto the plinth level 1:1.5:3 ( 1 cement: 1.5 c sand : 3 stone aggregate 20 mm nominal size ) as per sl no 4.1.2 6 centering and shuttering i / c strulting, propping etc. and removal of form work for column, piers , aboutments, post, and struts same as per sl no 5.9.5 7 e / w in cutting and filling in mix soil i / c a cortage of 1 km distance including all complete of work. 8 brick work with common burnt clay ( non modular ) bricks of class 150 super structure in cement mortar 1;6same as per sl no 6.4.2& 6.5 9 brick work with common burnt clay ( non modular ) bricks of class 150 super structure in cement mortar 1:4same as per sl no 6.4.1& 6.5 10 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto the plinth level 1:1.5:3 ( 1 cement: 1.5 c sand : 3 stone aggregate 20 mm nominal size ) as per sl no 4.2.2 11 centering and shuttering i / c strulting, propping etc. and removal of form work for column, piers , aboutments, post, and struts same as per sl no 5.9.20 12 m.s. of iron workin plain work such as reinforcement concrete / brick work ( when not included in over all rates ) wrought to required shapes as necessary including bending for proper completion of the work and including supply of steel, its westage and hooks and authoriesed over lapping shall be measered ….as per rate analysis based on sail latest rate 13 steel work welded in built up sections / framed work, i / c cutting fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar , ladder, railings, brackets grates and similar works same as per sl no 10.25.2 14 providing & fixing 1 mm thk ms sheet doors &windows with frame of 40x40x6mm angle iron, and 3 mm gusset plates at the junctions and corners all necessary fittings complete i / c applying a priming coat of approved steel primer same as per sl no 10.5.1 15 providing and fixing isi marked flush door shutters confurming to is 2202 ( part 1 ) non decorative type core of block board construction i / c all etc. completed 30 mm thk i / c isi marked stainless steel but hingh with neccessorysl no 9.21.2 & 9.26 16 providing & fixing isi marked oxidised ms handle conferming to isi 4992 with neccessory screws etc completed 17 providing & fixing isi marked bright finish tower bolt with neccessory screws etc completed 18 12mm thick cement plaster of mix 1:6 cementc sand i / c al etc. required for proper comletion of work as per si no.13.4.2 19 cement concrete flooring in 1:2:4 ( 1 cement: 2 c sand : 4graded stone aggregate 20 mmsize ) finish with a floating coat of neat cement i / c cement slurry but excluding the cost of noising of steps etc completed 40 mm thk with 20 mm nominal size of stone aggregate as per sl no 11.3.1 20 fixing panesof glass2.8to 3.7mm with aual or equivalent isi marked quality putty brads and springs complete. 21 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto the plinth level 1:4:8 ( 1 cement: 4 c sand : 8 brick aggregate 40 mm nominal size ) as per sl no 4.1.8 22 finishing wall with premium acrylic smooth exterior paint with silicon additives or required shade, new work two or more coat applied @ 1.67 ltr / 10 sqm over and priming coat….as per pwd specification of ayodhya scheduled item no.13.46.1 23 paint or venishing new iron work or new wood work withone coat priming and two coat of approved paint i / c all material labour t&p ….as per pwd specification 15.1.1 scheduled item no. 641 & 642 24 providing and fixing of 110 mm outer dia . pvc pipe 6 kg / cm2 pressure i / c all etc completed 25 providing and layingrectified glazed ceramic floor tiles of size 300x300 mm or more ( thickness to specified by the manufacturar ) of ist quality conforming to is 15622 of the approved brand and manufacture in all colour and shade laidon 20mm thk cement mortar 1:4 joint with grey cement slurry @ 3.3 kg / sqm i / c grouting the joint with white cement with matching pigments etc. completed size of tile 600x600 mm same as per sl no 11.39 26 wiring point for light in pvc conduit with 1.5 sqm. fr pvc insulated multistarand copper conductor cable as earth wire drawn inside the conduit. si no. 131 © 27 wiring point for fan / fresh air fan in pvc conduit with 1.5 sqm. fr pvc insulated multistarand copper conductor cable as earth wire drawn inside the conduit. si no. 133 © 28 s / f of power plug with 15 a / 250 v flush type switch & 5 pin 15 a / 250 v flush type universal socket. si no. 1139 29 s / f hexagonal fan box. as si no. 1149. 30 s / f of switch box of 16 swg dully painted with red oxide primer and flushed with wall.1203 31 s / f of batten / angle holder complete. si no. 405 32 s / f suface / flush mounting 4 ways spn distribution board ( legrand lexic ) with additional metal door with out mcb complete in all respect. si no. 1022 b 33 s / f of 6 amp to 32 amp spmcb ( 10 ka ) ( legrand lexic ) si no 1002 ( a ) . 34 provide and fixing of cpvc pipe having thermal suitability for hot and cold water supply, i / c all cpvc plain & brass threaded fitting i / c the fixing of pipe with clamp at 1.0 m spacing this i / c the joint of pipes & fitting one steps cpvc solvent cement and testing of joints complete with direction of engineer in charge external work 15 mm nominal outer dia pipes 35 provide and fixing of cpvc pipe having thermal suitability for hot and cold water supply, i / c all cpvc plain & brass threaded fitting i / c the fixing of pipe with clamp at 1.0 m spacing this i / c the joint of pipes & fitting one steps cpvc solvent cement and testing of joints complete with direction of engineer in charge external work 20 mm nominal outer dia pipes 36 provide and fixing of cpvc pipe having thermal suitability for hot and cold water supply, i / c all cpvc plain & brass threaded fitting i / c the fixing of pipe with clamp at 1.0 m spacing this i / c the joint of pipes & fitting one steps cpvc solvent cement and testing of joints complete with cost of cutting chases and making good the same direction of engineer in charge internal work15 mm nominal outer dia pipes 37 provide and fixing of cpvc pipe having thermal suitability for hot and cold water supply, i / c all cpvc plain & brass threaded fitting i / c the fixing of pipe with clamp at 1.0 m spacing this i / c the joint of pipes & fitting one steps cpvc solvent cement and testing of joints complete with cost of cutting chases and making good the same direction of engineer in charge internal work20 mm nominal outer dia pipes 38 providing & fixing of brass bib cock of approved quality 15 mm nominal bore 39 providing & fixing of brass stop cock of approved quality 15 mm nominal bore 40 provide and fixing wash basin with ci bracket 15 mm cp brass pillar traps32 mm cp brass waste of standard pattern i / c painting of fitting and brackets cutting and making good the walls whereever required white vitreous china wash hand basin size 630x450 mm with asingle 15 mm cp brass piller tap....

Rural Engineering Department - Uttar Pradesh

34066942 tender for pt. deendayal upadhyay r.m. inter college tenduakaji laboratory ( physics science ) development block dostpur 1 cleaning jungle i / c uprooting of rank vegitation, grass brush wood, tree and sapling of girth up to 30 cm measured at a height of 1 m above ground level and remoovel of rubbish upto distance of 50 mas per sl no 2.31 2 earth work in surface excavation not exceeding 0.30m and above in depth but exceeding 1.50 m in width as well as 10 sqm on plan i / c getting out and disposal of excavated earth upto 50m and lift upto 1.50m as directed by engineer in charge 2.1.1 all kind of soil as per si no 2.6.1 3 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto the plinth level 1:6:12 ( 1 cement: 6 c sand : 12 brick aggregate 40 mm nominal size ) as per sl no 273 4 brick work with common burnt clay ( non modular ) bricks of class 150 in foundation and plinth in cement mortar 1;6same as per sl no 6.1.2 5 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto the plinth level 1:1.5:3 ( 1 cement: 1.5 c sand : 3 stone aggregate 20 mm nominal size ) as per sl no 4.1.2 6 centering and shuttering i / c strulting, propping etc. and removal of form work for column, piers , aboutments, post, and struts same as per sl no 5.9.5 7 e / w in cutting and filling in mix soil i / c a cortage of 1 km distance including all complete of work. 8 brick work with common burnt clay ( non modular ) bricks of class 150 super structure in cement mortar 1;6same as per sl no 6.4.2& 6.5 9 brick work with common burnt clay ( non modular ) bricks of class 150 super structure in cement mortar 1:4same as per sl no 6.4.1& 6.5 10 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto the plinth level 1:1.5:3 ( 1 cement: 1.5 c sand : 3 stone aggregate 20 mm nominal size ) as per sl no 4.2.2 11 centering and shuttering i / c strulting, propping etc. and removal of form work for column, piers , aboutments, post, and struts same as per sl no 5.9.20 12 m.s. of iron workin plain work such as reinforcement concrete / brick work ( when not included in over all rates ) wrought to required shapes as necessary including bending for proper completion of the work and including supply of steel, its westage and hooks and authoriesed over lapping shall be measered ….as per rate analysis based on sail latest rate 13 steel work welded in built up sections / framed work, i / c cutting fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar , ladder, railings, brackets grates and similar works same as per sl no 10.25.2 14 providing & fixing 1 mm thk ms sheet doors &windows with frame of 40x40x6mm angle iron, and 3 mm gusset plates at the junctions and corners all necessary fittings complete i / c applying a priming coat of approved steel primer same as per sl no 10.5.1 15 providing and fixing isi marked flush door shutters confurming to is 2202 ( part 1 ) non decorative type core of block board construction i / c all etc. completed 30 mm thk i / c isi marked stainless steel but hingh with neccessorysl no 9.21.2 & 9.26 16 providing & fixing isi marked oxidised ms handle conferming to isi 4992 with neccessory screws etc completed 17 providing & fixing isi marked bright finish tower bolt with neccessory screws etc completed 18 12mm thick cement plaster of mix 1:6 cementc sand i / c al etc. required for proper comletion of work as per si no.13.4.2 19 cement concrete flooring in 1:2:4 ( 1 cement: 2 c sand : 4graded stone aggregate 20 mmsize ) finish with a floating coat of neat cement i / c cement slurry but excluding the cost of noising of steps etc completed 40 mm thk with 20 mm nominal size of stone aggregate as per sl no 11.3.1 20 fixing panesof glass2.8to 3.7mm with aual or equivalent isi marked quality putty brads and springs complete. 21 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto the plinth level 1:4:8 ( 1 cement: 4 c sand : 8 brick aggregate 40 mm nominal size ) as per sl no 4.1.8 22 finishing wall with premium acrylic smooth exterior paint with silicon additives or required shade, new work two or more coat applied @ 1.67 ltr / 10 sqm over and priming coat….as per pwd specification of ayodhya scheduled item no.13.46.1 23 paint or venishing new iron work or new wood work withone coat priming and two coat of approved paint i / c all material labour t&p ….as per pwd specification 15.1.1 scheduled item no. 641 & 642 24 providing and fixing of 110 mm outer dia . pvc pipe 6 kg / cm2 pressure i / c all etc completed 25 providing and layingrectified glazed ceramic floor tiles of size 300x300 mm or more ( thickness to specified by the manufacturar ) of ist quality conforming to is 15622 of the approved brand and manufacture in all colour and shade laidon 20mm thk cement mortar 1:4 joint with grey cement slurry @ 3.3 kg / sqm i / c grouting the joint with white cement with matching pigments etc. completed size of tile 600x600 mm same as per sl no 11.39 26 wiring point for light in pvc conduit with 1.5 sqm. fr pvc insulated multistarand copper conductor cable as earth wire drawn inside the conduit. si no. 131 © 27 wiring point for fan / fresh air fan in pvc conduit with 1.5 sqm. fr pvc insulated multistarand copper conductor cable as earth wire drawn inside the conduit. si no. 133 © 28 s / f of power plug with 15 a / 250 v flush type switch & 5 pin 15 a / 250 v flush type universal socket. si no. 1139 29 s / f hexagonal fan box. as si no. 1149. 30 s / f of switch box of 16 swg dully painted with red oxide primer and flushed with wall.1203 31 s / f of batten / angle holder complete. si no. 405 32 s / f suface / flush mounting 4 ways spn distribution board ( legrand lexic ) with additional metal door with out mcb complete in all respect. si no. 1022 b 33 s / f of 6 amp to 32 amp spmcb ( 10 ka ) ( legrand lexic ) si no 1002 ( a ) . 34 provide and fixing of cpvc pipe having thermal suitability for hot and cold water supply, i / c all cpvc plain & brass threaded fitting i / c the fixing of pipe with clamp at 1.0 m spacing this i / c the joint of pipes & fitting one steps cpvc solvent cement and testing of joints complete with direction of engineer in charge external work 15 mm nominal outer dia pipes 35 provide and fixing of cpvc pipe having thermal suitability for hot and cold water supply, i / c all cpvc plain & brass threaded fitting i / c the fixing of pipe with clamp at 1.0 m spacing this i / c the joint of pipes & fitting one steps cpvc solvent cement and testing of joints complete with direction of engineer in charge external work 20 mm nominal outer dia pipes 36 provide and fixing of cpvc pipe having thermal suitability for hot and cold water supply, i / c all cpvc plain & brass threaded fitting i / c the fixing of pipe with clamp at 1.0 m spacing this i / c the joint of pipes & fitting one steps cpvc solvent cement and testing of joints complete with cost of cutting chases and making good the same direction of engineer in charge internal work15 mm nominal outer dia pipes 37 provide and fixing of cpvc pipe having thermal suitability for hot and cold water supply, i / c all cpvc plain & brass threaded fitting i / c the fixing of pipe with clamp at 1.0 m spacing this i / c the joint of pipes & fitting one steps cpvc solvent cement and testing of joints complete with cost of cutting chases and making good the same direction of engineer in charge internal work20 mm nominal outer dia pipes 38 providing & fixing of brass bib cock of approved quality 15 mm nominal bore 39 providing & fixing of brass stop cock of approved quality 15 mm nominal bore 40 provide and fixing wash basin with ci bracket 15 mm cp brass pillar traps32 mm cp brass waste of standard pattern i / c painting of fitting and brackets cutting and making good the walls whereever required white vitreous china wash hand basin size 630x450 mm with asingle 15 mm cp brass piller tap....

Cane Development and Sugar Industry - Uttar Pradesh

33873476 farm machinery work in the pilibhit campus of cooperative sugarcane development society 2 filling of carted earth. 3 sand filling in plinth under floors including watering, ramming, consolidating and dressing complete including lead up to 50m and lift up to 1.5m and including cost of sand. 4 providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size) and curing complete, including cost of form work, in foundation and floors. 5 as in item 6 but for thelighterbeams i.e. having spans upto 6 m. (using 1:1.5:3 mix concrete) ground floor 6 as in item 6 abovebut inr.c.c.raft foundation and footingwithapproved stone ballast.(using1:1.5:3mix concrete) (upto plinth) 7 as in item 6 above but in r.c.c. columns in 1:1.5:3 having strength not less than m 20. ground floor 8 same as in item no. 10 abovebutin super structure above plinth level up to floor two level ( up to two storeys ) includingnecessarycutting and moulding of brick work asrequiredand also including honeycombed brick work in thickness of wall more than 12cms. ground floor 9 p/f mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. ground floor 10 providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete.fixed to steel windows by welding 11 15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand) 12 12 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 6 fine sandground floor 13 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. (1) 1 cement : 6 fine sand ground floor 14 cement concrete flooring 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 12 20mm nominal size laid in one layer neat cement (40 mm thick floor). 15 cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.18 mm thick ground floor 16 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade :new work (two or more coats applied @ 1.43 ltr/ 10sqm over and including priming coat of exterior primerapplied @ 2.20 kg/ 10 sqm) ground floor 17 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 18 distempering (two coat) with oil bound distemper of approved brand and manufacture & of required shade on ceiling to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as berger, j & n, shalimar, asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters including cost of all labour & materials. ground floor 19 applying putty base 20 mild steel or iron work in heavy sizes such astrusses, builtup gate,roof work etc., wrought to required formincluding cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.electric resistance or induction butt welded tubes 21 providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by engineer in charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineerin charge. the sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with epdm seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 22 painting ist coat over priming coat (butexcluding cost of priming coat) on steelandothermetalsurfacesup to 10 cm. widthorgirthorsmall articles not exceeding 0.10sqm in area white superior synthetic enamel such as luxol3,hi glossapcolitesuperlac,dulux specifiedbrushingtogiveanevenshadeandincluding cleaningthe surfaceofalldirt,dust and other foreignmatter sandpaperingand stopingincluding cost ofall materials, labour toolsandplantsetc. required forpropercompletion ofthe work. 23 add cost of electrical work ...

Cane Development and Sugar Industry - Uttar Pradesh

33873374 work of farm machinery in cooperative sugarcane development society, puranpur 1 excavation of foundation in ordinary soil ( loam clay or sand ) including lift upto 1.50 meter and lead upto 30 meter and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of foundation trenches or into the plinth and removal and disposal of sur plus earth as directed by the engineer in charge up to a distance of 30 meters from the foundation trenches. 2 filling of carted earth. 3 sand filling in plinth under floors including watering, ramming, consolidating and dressing complete including lead up to 50m and lift up to 1.5m and including cost of sand. 4 providing and laying in cement concrete 1:4:8 ( 1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size ) and curing complete, including cost of form work, in foundation and floors. 5 as in item 6 but for thelighterbeams i.e. having spans upto 6 m. ( using 1:1.5:3 mix concrete ) ground floor 6 as in item 6 abovebut inr.c.c.raft foundation and footingwithapproved stone ballast. ( using1:1.5:3mix concrete ) ( upto plinth ) 7 as in item 6 above but in r.c.c. columns in 1:1.5:3 having strength not less than m 20. ground floor 8 first class brick work in 1:6 cement and coarse sand of 2.25 fineness modulus ) mortar infoundation & plinth including supply of all materials, labour and t & p etc reqiored for proper completion of the work.butin super structure above plinth level up to floor two level ( up to two storeys ) includingnecessarycutting and moulding of brick work asrequiredand also including honeycombed brick work in thickness of wall more than 12cms. ground floor 9 p / f mild steel or iron in plain work such as reinforced concrete or reinforced, brick work ( when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. ground floor 10 providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete.fixed to steel windows by welding 11 15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 ( 1 cement: 4 coarse sand ) 12 12 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. ( 1 ) 1 cement : 6 fine sandground floor 13 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and / or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. ( 1 ) 1 cement : 6 fine sand ground floor 14 cement concrete flooring 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 12 20mm nominal size laid in one layer neat cement ( 40 mm thick floor ) . 15 cement plaster skirting up to 30 cm height, with cement mortar 1:3 ( 1 cement : 3 coarse sand ) , finished with a floating coat of neat cement.18 mm thick ground floor 16 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade :new work ( two or more coats applied @ 1.43 ltr / 10sqm over and including priming coat of exterior primerapplied @ 2.20 kg / 10 sqm ) ground floor 17 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 18 distempering ( two coat ) with oil bound distemper of approved brand and manufacture & of required shade on ceiling to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as berger, j & n, shalimar, asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters including cost of all labour & materials. ground floor 19 applying putty base 20 mild steel or iron work in heavy sizes such astrusses, builtup gate, roof work etc., wrought to required formincluding cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.electric resistance or induction butt welded tubes 21 providing and fixing precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm ( + 0.05 % ) total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineerin charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55 mm ) with epdm seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 22 painting ist coat over priming coat ( butexcluding cost of priming coat ) on steelandothermetalsurfacesup to 10 cm. widthorgirthorsmall articles not exceeding 0.10sqm in area white superior synthetic enamel such as luxol3, hi glossapcolitesuperlac, dulux specifiedbrushingtogiveanevenshadeandincluding cleaningthe surfaceofalldirt, dust and other foreignmatter sandpaperingand stopingincluding cost ofall materials, labour toolsandplantsetc. required forpropercompletion ofthe work. 23 add cost of electrical work...

Uttar Pradesh Housing And Development Board - Uttar Pradesh

33143736 construction of remaining work at p.h.c., kapsad, meerut. 1 excavation in foundation in ordinary soil ( loan clay ot sand ) including lift upto 1 50 meters and lead upto 30 mitr. including filling watering and tranming of excavated earth in the trenches of the building between the building and the sides of foundati trenches or in the plinth and extraction of disposal; as directed by the engineer incharge, the foundation trenches from 30m ( including royality ) 2 fillingof carted earth incide the plinth including cartage from a distance not less than 8 kms also including levelling dressing watering & ramming complete & cost of earth & royality etc. 3 sand filling in plinth including supply of necessary quantity of sand from a distance not excluding 8km from the site of work and including watering dressing etc. rate to include cost of all materials, labour and t&p etc.required for proper completion of the work. 4 providing and layingin cement concrete 1:4:8 ( 1 cement :4 coarse sand :8stone ballast 40 mm nominal size ) and curing complete, including cost ofform work, in foundation and floors complete including cost of all materials, labour and t&p etc.required for proper completion of the work. 5 cement concrete 1:1.5:3 ( 1 cement : 1.5coarse sand : 3 graded stone aggregate 20 mm nominal size ) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete. 6 providing and laying in position bitumen hot sealing compound for expansion joints etc. dsr 16.46.1using grade a sealing compound. 7 contruction of apron drain ( 150*150 mm size, for 1.00m. length ) 8 providing and injecting chemical emulsion for constructional antitermite treatment and creating a chemical barrier under and alround the column pits. wall trenches basement excavation top surface of plinth fillingjunction wall and floor along the external perimeter of binding expansion joints, surrounding of pipes and conduit etc complete ( plinth area of building at ground floor only, shall be measured as per 6313 ( part ii 1981 ) excluding gst. aldrine emulsifiable concen trate any other approved material such as heptrachlor or chlordance will be used. the rate of application of chemical emulsion shall be as follows: ( 1 ) treatment for masonry 8 foundation 5 liters per sqm. ( 2 ) , back fill in immediate contact with foundation 7.50 liters per sqm. ( 3 ) treatment of top surface of plinth fillings 5 ??liters / sqm. ( 4 ) .treatment ofsoil along external perimeter of building 7.50 liters / sqm. ( 5 ) . treatment of soil under apron along with external perimeter 5 liters / sqm. 9 first class brick work in 1:4 cement and coarse sand ( fm 1.50 to 2.20 ) mortar infoundation & plinth including supply of all materials, labour and t & p etc. 10 first class / class 150 brick work in1:6cement and coarsesand ( fm 1.50 to 2.20 ) mortar in foundation and plinth including supply of all materials, labour and tools and plants etc. required for propercompletion of the work. 11 r.c.c. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 bwg binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than m 20. 12 same as in above item but for slabs ( using 1:1.5:3 mix concrete ) 13 same as in above item but for the lighterbeams i.e. having spans upto 6 m. ( using 1:1.5:3 mix concrete ) 14 same as in above item but for footing ( using 1:1.5:3 mix concrete ) 15 same as in above item but for column ( using 1:1.5:3 mix concrete ) 16 cast cement concrete door sills, chaukhats, boundary posts shelves and similar small work with cement, approvedcoarse sand and 2 cm gauge stone grit in proportions of 1:2:4 excluding its fixing and binding the same with 24 b.w. g.g.i., binding wire, moulds, all materials labour, tools & plants etc. required for proper completion of the work. the rateexcludes making of drip course which shall be paid extra. 17 first class / class 150 brick work in1:6cement and coarsesand ( fm 1.50 to 2.20 ) mortar in super structureincluding necessary cutting and moulding of brick work as required and also includinghoney combed brick work in thickness of wall more than 12cms.including supply ofall materials, labourand tools and plants etc. requiredforpropercompletion of the work. 18 first class / class 150 brick work in1:4cement and coarsesand ( fm 1.50 to 2.20 ) mortar in super structureincluding necessarycutting and mouldingofbrickworkas required andalsoincludinghoney combed brick work in wall thickness 12 cms & below..including supply ofall materials, labourand tools and plants etc. requiredforpropercompletion of the work. 19 painting on d.p.c. with two coats of air blown bitumen vg 10 grade @ 1.70 kg / sqm approximate including cost of fuel if any. 20 providing and laying brick koba 12 mm thick laid with m 150 class brick bat coba 7.50 cm thick with gap of 15 mm to each other over 20 mm thick base of cement mortar 1:4 cement and course sand mixed with water proofing compound preading cement slurry mixed with aereclic cement concrete water proofing compound filled gaps of coba & top of coba mortar finished smooth & top mashed false square 30 cm xcm and side wall parapet shall be mono tythic plaster wall upto 30 cm higher and junction and corner shall be rounded by brick ballast and course sand masonary coba with top finshed plaster mixed with acetic water proofing compound @ 2% by weight & including s / o all material, labour, t&p etc complete for proper comletion of the work. 21 supply and fixingof flushdoors commercialqualityconformingtoi.s.2202 part i ( 1983 ) includingfixingof wooden cleats and stoppers and including fixing and adjustment of hinges, bolts, locks, handle, springs and other fitting with necessary screws complete. 35 mm thick 22 mild steel or iron workofsmall sizes and sections suchand holding down bolts, holdfasttierods, gratings etc. ( when notincludedinan overall rates ) wroughttorequiredfromincluding supply ofsteel anditswastage includingcostof bolts, nuts if required forandwelding, grinding and making holes as required completion of workfabricationofholesdoors, chaukhats nosing. ( a ) fabrication of holdfast & door chaukhat. 23 ( b ) same as in above item but for fabrication of grill / stairscase railing / gate. 24 ( c ) same as in above item but for fabrication of z section steel windows.openable 25 providing and fixing fly proof galvanized m.s. wire gaugeto windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete with 12 mm mild steel u beading 26 providing and fixing wire gauge shutters using galvanized m.s. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :35 mm thick shutters with isi marked m.s. pressed butt hinges bright finished of required size kiln seasoned and chemically treated hollock wood 27 supply and fixing of 24 guage aluminium sheet on toilet door shutters bottom including fixing with aluminium greves, labour including labour t&p etc required for proper completion of the work 28 mild steel or iron in plain work such as rcc or r.b. work wrought to required shape as necessary including bending for proper competition of the work and including supply of all steel & wastage and over lapping and hooks. 29 fixingofsteelorwoodenchaukhats in position. ( a ) door chaukhats window chaukhats above 1.5 sqm. and upto 3.0 sqm. 30 ( b ) same as in above item but for window chaukhats up to 1.5 sqm 31 ( c ) same as in above item but for ventilator chaukhats 32 12mm thick plaster with 1 cement : 6 course sand over brick work, minimum thickness not to be less than 3 / 8 ( 10mm ) thick including supply of all materials, labour and tools and plants etc required for completion of the work. 33 12 mm cement plaster on rough side with 1 cement : 6 course sandover brick work, minimum thickness not to be less than 3 / 8 ( 10mm ) thick including supply of all materials, labour and tools and plants etc required for completion of the work. 34 12 mm bearing plaster 1 cement:6 coarsesand 35 making grooves 10 to 12 mm wide x 8 mm deep in plaster of the wall or in celling vertically or horizontally as required. 36 making drip course in sun shade facia as per direction of engineering charge including supply of all material labour etc. required for proper completion of the work. 37 supply and fixing 6 mm ( 1 / 4 ) thick china white glazedtiles inflooringorin skirting or dado laid with1:3 cement and approved coarse sand mortar finished with whitecement slurry jointing and polishing complete includingsupplyof allmaterials, labour and tool sand plantsetc.required forproper completion of the work. excluding gst. 38 2.5 cm thick 1:2:4 plain cement concretefloor with cement approved coarse sand and 2cm. graded approved stone ballast laid in planels finished with 3mm ( 1 / 8 ) floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified over and including 8 cm. ( 3 ) local sand and brick ballast 4 cm. gause in proportion of 1:4:8 and removing any giving then a uniform finish, including supply of all materials, labour, t&p etc. required for proper completion of the work. but without base concrete. 39 cement concrete flooring 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size ) laid in one layer finished with a floating coats neat cement ( 40 mm thickfloor ) . 40 2 cm. ( 3 / 4 ) thick cement plaster in dedo or skirting in 1:2 consisting of one part of cement and 2 parts of approved coarse sand laid in pannels, finished with 3 mm ( 1 / 8 ) floating coat of neat cement or cement and marble dust in ratio of 5 1 including supply of all materials labour and t & p etc. required proper completion of the work 41 providing and laying 25 mm kota stone flooring over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid over jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete. 42 providing& laying of vitrified tiles of 600 mm x 600 mm size ( thickness 10 mm ) with water absorption less than .08% and conforming to is: 15622, of approved brand & manufacturer, in desired colours and shades, laid with cement based high polymer modified quick set tile adhesive ( water based ) conforming to is15477 including grouting of joints. 43 18 mm thick marble tiles in rises of step skirting dado wall and pillars laid on 10mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) jointed with gray cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete. 44 painting or varnishing work in small areas or new wood work with one coat ( upto one sqm of ready mixed priming paint and one coat of approved superior quality ready mixed paint or varnish including supply of all materials, labour toolsandplants etc. required forpropercompletion of the work. piant to be used isi marked. ( for two coat ) 45 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade :new work ( two or more coats applied @ 1.43 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm ) ( apex ultima, weather coat all guard ) assian, berger. 46 finishingwallswith water proofing on cementpaint of approvedmakesuch as super snowcem, durrocem, robiacem, guttucem supercem qualityandof required shade on undecorated wall surfaces ( two coat ) overone andincludingonecoatwhite cementprimertogiveaneven shade after thoroughly brushing the surface to powdered materialsincluding curing and cost of all materials. 47 one priming coat and one coat oil distemper on new work incliding supply of all materials, labour and t&p required for proper completion of the work ( for two coat ) 48 finishing wall with acrylic emulsion paint of approved brand and manufacture and of required shade and undecorated wall surface to give an even shade over including curing and cost of all material, labour, t&p etc. required for proper completion of the work for two coat. 49 providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : with 4.0 mm thick glass panes. 50 providing and fixing glass strips in joints of terrazo / cement concrete floors. 51 providing stainless steelsliding bolts16 mm dia with nuts and 250 mm long. 52 providingstainless steel towerboltwith10 mmdia and screw.300 mm long 53 providing and fixing stainless steel handle with screws etc. complete ( a ) 150 mm 54 providing and fixing oxidised sliding door bolts isi marked anodisedwith nuts and screws etc. complete : 300x16 mm 55 providing and fixing oxidised tower bolts isi marked anodisedwith necessary screws etc. complete :250x10 mm 56 providing and fixing oxidised handles isi marked anodisedwith necessary screws etc. complete : 100 mm 57 providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of t iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer 58 providing and laying 80mm thick factory madeinter locking c.c. paver block of m 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer in charge. 59 water supply and sanitary : providing and fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with isi marked white solid plastic seat and lid, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) , conforming to is : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. 60 providing and fixing water closet squatting pan ( indian type w.c. pan ) with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) conforming to is : 7231, with all fitting and fixtures completed including cutting and making good the walls and floors wherever required.white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests. 61 providing & fixing white viterous china wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standardpattern, including painting of fitting and brackets, cutting & making good the walls wherever required. flat back wash basin size 550x400 mm with single 15mm c. p. brass pillar tap 62 providing and fixing flexible p.v.c. waste pipe for sink or wash basin including pvc waste fittings complete.32 mm dia ( for wash basin ) 63 same as in above item but for 40 mm dia ( for sink and urinal ) 64 providing & fixing 600 x 450 mm bevelled edge mirror of superiorglass ( of approved quality ) complete with 6mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. 65 providing & fixing stainless steel a isi 304 ( 18 / 8 ) kitchen sink as per is:13983 with c.i. bracketsandstainless steel plug 40 mm including painting of fittings and brackets cutting and making good the walls wherever required. 610 x 460 bowl depth 200 mm 66 s / f of upvc swr pipe type b confirming to is 13592 incluiding jointing the pipes with rubber ring lubricant and upvc swr cuplar confirming to is 14735 also inluiding excavation of treches cutting of walls and holes and repairing of walls , floors and refilling the trenches as before cut including cost of other fittings such as door band, t and yt including supply of all materials labour and t&p required for prper complition of the work.110mm dia swr pipe 67 same as above item but for 90mm dia swr pipe 68 same as above item but for 160mm dia swr pipe 69 s / f of upvc swr nahani trap size100 / 90mm confirming to is 14735 self cleaning design fixed in pcc 1:2:4 and supply and fixing of 125 mm dia heavy duty cp brass jali. 70 laying cement concre 1:5:10 in haunching s.w. pipes including concrete for bedding necessary form work and during complete.100 mm dia 71 same as above item but for 150mm dia 72 s / f of upvc swr cowel confirming to is 14735 110 mm 73 providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 74 providing and fixing of chlorinated polyvinyle chloride ( cpvc ) pipes, having thermal stability for hot and cold water supply, including all cpvc plain and brass threaded fittings, inluding fixing the pipe with clamps at 1 m. spacing . this includes jointing of pipes and fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. internal work exposed on wall.25mm dia nominal bore 75 same as in above item but for 32mm dia nominal bore 76 providing and fixing of chlorinated polyvinyle chloride ( cpvc ) pipes, having thermal stability for hot and cold water supply, including all cpvc plain and brass threaded fittings, inluding fixing the pipe with clamps at 1 m. spacing . this includes jointing of pipes and fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. concealed work including cutting chases and making good the wall etc.20mm dia nominal bore 77 same as in above item but for 25mm dia nominal bore 78 providing and fixing of chlorinated polyvinyle chloride ( cpvc ) pipes, having thermal stability for hot and cold water supply, including all cpvc plain and brass threaded fittings. this includes jointing of pipes and fittings with one step cpvc solvent cement, trenching , reifilling and testing of joints complete as per engineer in charge. external work.25mm dia nominal bore 79 same as in above item but for 32mm dia nominal bore 80 providing & fixing gun metal gate valve with c.i. wheel of approvedquality ( screwed end ) 25 mm nominal bore 81 providing and fixing ballvalve ( brass ) of approved quality complete. ( high or low pressure with plastic floats ) .15 mm nominal bore 82 providing&fixing15 mm nominal bore45 cm long unplasticised pvc connection pipewith brass unions. 83 providing & fixing 15 mm nominal bore cp brass bib cockof approved quality conformingtois 8931. 84 providing and fixing 15 mm nominal bore c.p brass long nose bib cock of approved qualityconforming to is standardsandweighing notlessthan 810 gms. 85 providing & fixing 15 mm nominal bore c.p. brassstop cock ( concealed ) of standard designandof approvedmakeconforming to is : 8931. 86 providing & fixing 15 mm nominal bore c.p brass angle valve for basin mixer and geyser points of approved quality conformingto is8931. 87 providing & fixing 100 mm dia c.p brass shower rose with 15mm inlet. 88 suppling and hoisting of sintex or equivalent high density polythylene seamless of piece moulded tanks and placing the same in proper position including all materials, lbours and t & p etc. for proper completion of the work. tank should be isi marked, sintex or equivalent and i / c all taxes.500litrescapacity 89 providing and fixing square mouths. w. gully trapgrade `a complete with c.i. gratingbrickmasonry chamber with f.p.s bricks and water tight ci cover with frame of 300 x 300 mm size ( inside ) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design. 150 x 110 mm. size p type 90 providing & fixing 450 mm long c. p. brass towel railcomplete with c.p. brass bracketsfixedtowoodencleats with c.p. brass screw. 91 providing & fixing isi marked ( is : 778 ) brass gatevalve ( class 1, pn 1 mpa ) with wheel of approvedquality ( screwed end ) . 15 mm nominal bore 92 same as in above item but for 20 mm nominal bore 93 providing & fixing of medium class pvc spout up to 300 mm. length including cutting and making good the walls and floors etc. as required. 50 mm dia 94 providing and fixing of chlorinated polyvinyle chloride ( cpvc ) pipes, having thermal stability for hot and cold water supply, including all cpvc plain and brass threaded fittings. this includes jointing of pipes and fittings with one step cpvc solvent cement, trenching , reifilling and testing of joints complete as per engineer in charge. external work.40mm dia nominal bore 95 same as in above item but for 50mm dia nominal bore 96 providing & fixing gun metal gate valve with c.i. wheel of approvedquality ( screwed end ) .50 mm nominal bore 97 construction of sewer connecting chamber having internal size 60 x 60 x 60 cm constructed in class 150 brick work in 1:6 cement and coarse sand mortar, 10 cm thick pcc 1:4:8 in base and internal side plasterred with 1:3 cement and coarse sand mortar including a floating coat of neat cement and 2.5 cm thick pcc 1:2:4 flooring of chamber and 5 cm thick top cover in rcc 1:1.5:3 including reinforcement steel ( analysis rate ) 98 internal electrificationwiring point for light with 1 sq. mm fr pvc insulated multistrand single core copper conductor cable in heavy guage pvc conduit pipe partly concealed in the wall and partly laid in slab with 1.5 sq. mm fr pvc insulated multistrand copper conductor cable as earth wire drawn inside of pipe, piano type switch and ceiling rose / angle / batten holder on 3 mm thick phenolic paminated backalite sheet etc. switches shall be fixed on suitable size ms box shunked in wall with 3 mm thick phenolic paminated backalite sheet and brass screws and washers complete in all respect as directed by engineering in charges including matching colour wash. 99 same as above item but for fan and fresh air fan. 100 same as above itembutfor 5ampplug point with piano type switch & socket etc. 101 same as above item but for call bellwith piano type switch or socket etc. 102 supply and fixing of power plug with 15a / 240v flush type switch and 5 pin 15a / 250 v flush type universal socket in suitable ms box of 175 mm x 100 mm x 50 mm size with henolic laminated bakelite sheet cover 3 mm thick fixed with brass machine screw and cup washer. 103 suppply and wiring of submain 2 number 2.5 sqmm fr pvc insulated 1100 v grade multisterilizationanded single core copper conductor cable in heavy duty 20 mm dia pvc conduit partly concealed in wall and partly laid in slab along with one number 1.50 sqmm fr pvc insulated multisterilization and copper conductor cable as earth contunity wire etc. complete in all respects. 104 suppply and wiring of submain 2 number 4 sqmm fr pvc insulated 1100 v grade multisterilizationanded single core copper conductor cable in heavy duty 20 mm dia pvc conduit partly concealed in wall and partly laid in slab along with one number 2.50 sqmm fr pvc insulated multisterilization and copper conductor cable as earth contunity wire etc. complete in all respects. 105 suppply and wiring of submain 2 number 6 sqmm fr pvc insulated 1100 v grade multisterilizationanded single core copper conductor cable in heavy duty 20 mm dia pvc conduit partly concealed in wall and partly laid in slab along with one number 4 sqmm fr pvc insulated multisterilization and copper conductor cable as earth contunity wire etc. complete in all respects. 106 suppply and wiring of submain with 4 number 10 sqmm fr pvc insulated 1100 v grade multisterilizationanded single core copper conductor cable in heavy duty 32 mm dia pvc conduit partly concealed in wall and partly laid in slab along with two number 6 sqmm fr pvc insulated multisterilization and copper conductor cable as earth contunity wire etc. complete in all respects. 107 s / f of surface / flush mountingspn distribution board without mcbcompletein all respects as directed at site.4 ways 108 s&f and making connection of 25a 2 pole 30ma elcb / rccb of din rail mounting complete in all respect as per direction and satisfaction to the engineer in charge. 109 s&f and making connection of 63a 2 pole 30ma elcb / rccb of din rail mounting complete in all respect as per direction and satisfaction to the engineer in charge. 110 supply, installation, testing and commissioningof main distributionboard suitable for required size incomer and single / three phase outgoing mcbs, ip 42 protection, double metal door, factory fabricated, wall mounting type in surface / recess, powder coated, 415 v / 250 amp copper bus bar, earth and neutral bar, removable gland plates, cable glands including connection with outgoing feeders completeinall respect. 111 s / f of surface / flush mountingspn distribution board without mcbcompletein all respects as directed at site. 12 ways 112 supply & fixingof 6 / 10 / 16 / 20 / 25 / 32 amp. sp mcb ( 10 ka ) 113 s / f of consumer unit flush / wall mounting type controlled by incoming 32 amp / 240 v spn switch fuse with outgoing circuits of 4 way 16 amp 240 v rewireable type distribution fuse boardcompletewith complete in all respects. ( cat. b ) 114 supply&burryingof 600mm x 600mm x 6.0mm g.i. plate, vertically for earthing with its top at least 3 m below ground level complete 20mm dia. g.i.pipe and funnelforwatering and one earthing lead ofno. 8swgg.i. wirein 15 mm dia. gi pipe uptoswitch board ( from apron to switch boardthecost of gi pipe & gi wire willbeextra ) 300mm square c.i. box with hinged cover, masonary housing alternate layer of charcoal / coke and salt atleast 150mm thick alround etc. as per the direction of engineer in charge complete in all respect . 115 supplying & laying of one number 8 to6 swg g. i. wirein 15 mm. dia. g. i.pipefor earthing, laidin groundor inwall duly concealedincludingthecostofcement, sand, labour, t&pandothermaterial required for proper completion ofthework as directed at site. 116 s / f of single light wall bracket on matching m.d.f.e.g. board base etc. completeinall respects. category a. 117 supply and fixing of recess / surface / pendent mounting round 10 to 15 watt led down lighter having powder coated die cast aluminium housing with heat sink, diffuser / reflector and driver set complete in all respect cat aaa 118 supply and fixing of led tube light with batten suitable for up to 1 x 22 watt led tube light complete including tube etc on surface complete in all respect.cat aaa 119 supply and fixing of electronic fan regulator 120 280 v isi marked on the existing switch board including making connection, required material, labour t&p etc. for proper completion of work to the satisfaction on engineer in charge of work. 120 s / f of hexagonal fan box with hexagonal side of approx. 80 mm.in lengthfabricatedfrom 16 swg m.s. sheet incorporating with10 mm. dia. m.s. round bar duly bent for supporting fan hanger duly painted with redoxideand screwingarrangementwithwiringconduit laid in the r.c.c.roofbeforeconcreting along with supply of all materials, labour, t&p etc. for proper completion of work. 121 s / f of doorchimeonpolishedm.d.f.e.g. board includingmakingconnectionsetc. complete in all respects. 122 supply of ceilling fans with fan motor of a.c. permanent insulation, capacitor rating conforming bee 5 starr rating and is:374 / 79 and also comply with is: 1709 / 1984 with latest amendment. the rated voltage 220 / 240 volts, 50hz, 1 ph ac the fan assemble should consits of down rod blades, shackle canopies etc. and with double ball bearing system. ( i ) bee 5 star rated 1200 mm sweep 123 supply of ac230 / 250 volts, 50 hz exhaust fansincluding providingnuts, bolts, mounting frame and other accessories etc. complete. ( make : bajaj / usha / newtek / havells ) 300 mm sweep...

Uttar Pradesh Jal Nigam - Uttar Pradesh

32922512 supply of materials for various modification and renovation works under “sugamya bharat abhiyan” at board of revenue, lucknow board of revenue ( remaining items ) board of revenue ( remaining items ) , dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead for thickness of tiles 10 mm to 25 mm , 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 ( 1 cement: 4 coarse sand ) , dismantling doors and windows, chowkhats with holdfast and including stacking of materials as directed by engineer in charge with in adistance of 60 metre. , dismantling doors and windows leaves and including stacking of dismantled materials as directed by engineer in charge with in adistance of 60 metre. , repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.metersand under, including cutting the patch in proper shape, raking out joints andpreparing and plastering the surface of the walls complete, including disposalof rubbish to the dumping ground, all complete as per direction of engineerin charge. ground floor , 6 mm cement plaster 1:3 ( 1 cement : 3 fine sand ) finished with a floating coat ofneat cement and thick coat of lime wash on top of walls when dry for bearingof r.c.c. slabs and beams ground floor . , making grooves 10 to 12 mm wide x 8mm deep in of the wails or in ceiling vertically or horizontallyas required , providing and laying ceramic glazed floor tiles of size 300x300 mm ( thicknessto be specified by the manufacturer ) of 1st quality conforming to is : 15622 ofapproved make in colours such as white, ivory, grey, fume red brown, laid on20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with greycement slurry @ 3.3 kg / sqm including pointing the joints with white cementand matching pigment etc., complete. , providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineerin charge, in skirting, risers of steps and dados, over 12 mm thick bed of cementmortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matchingshade complete. , cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stoneaggregate ) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate. , providing and fixing isi marked flush door shutters conforming to is : 2202 ( parti ) non decorative type, core of block board construction with frame of 1st classhard wood and well matched commercial 3 ply veneering with vertical grains orcross bands and face veneers on both faces of shutters: 35 mm thick including isi marked stainless steel butt hinges with necessary screws , providing and fixing m.s. rivets of sizes in position. , providing and fixing of hold fast for chaukhats of door sin addition, windows. , providing of door / windows grill , z section steel windows ( open able ) , angle iron door chaukhats 40x40x5 , fixing of door, window / ventilator chaukhats in position , one priming coat & one coat oil distemper on new work including supply of all materials, labour and t& p etc. required for proper completion of the work.as in item no.649 above but for every coat after the first coat ground floor , finishing walls with premium acrylic smooth exterior paint with siliconeadditives of required shade: new work ( two or more coats applied @ 1.43 ltr / 10 sqm over and includingpriming coat of exterior primer applied @ 2.20 kg / 10 sqm ) ground floor , one priming coat & one coat oil distemper on new work including supply of all materials, labour and t& p etc. required for proper completion of the work.as in item no.649 above but for every coat after the first coat ground floor , providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface toprepare the surface even and smooth complete.ground floor , painting or vanishing on iron works in small areas or new wood work with one coat of ready mixed priming paint & one coat of approved superior quality ready mixed paint of clear synthetic varnish including supply of all materials, labour and t & p etc. required for proper completion of work. paint to be used should confirm to the i.s.i. no. 103 1950.same as in item 641 above but for every coat after 1st coat. details of cost for 650 sft. area , wood surface. , providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes , ramp with slope 1:12 & width of 1.8 m & plinth height of 300 mm from ground level with steel handrails & chequred tiles. , supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. , providing and laying in position cement concrete of specified grade excludingthe cost of centering and shuttering all work up to plinth level : 1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) : 8 graded stone aggregate 40 mmnominal size ) , centering and shuttering including strutting, propping etc. and removal of formfor foundations, footings, bases of columns, etc. for mass concrete , providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all workup to plinth level : 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) : 3 graded stone aggregate 20 mmnominal size ) , brick work with common burnt clay f.p.s. ( non modular ) bricks of classdesignation 7.5 in foundation and plinth in: cement mortar 1:6 ( 1 cement : 6 coarse sand ) b / w in foundation , brick work with common burnt clay f.p.s. ( non modular ) bricks of classdesignation 7.5 in superstructure above plinth level up to floor v level in all shapesand sizes in : cement mortar 1:4 ( 1 cement : 4 coarse sand ) b / w up to plinth lvl. , steel reinforcement for r.c.c. work including straightening, cutting, bending, placingin position and binding all complete upto plinth level. thermo mechanically treated bars of grade fe 500d or more. , cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stoneaggregate ) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. , chequered precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cementslurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 10 mm thick bed of cement mortar 1:4 ( 1 cement: 4 coarse sand ) . ordinary cement without any pigment , providing and laying tactile tile ( for vision impaired persons as per standards ) of size 300x300x9.8mm having water absorption less than 0.5% and conforming to is: 15622, of approved make in all colors and shades in outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of engineer in charge. , providing and fixing stainless steel ( grade 304 ) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, i / c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer in charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. ) . , pathway marking , parking , internal electrical ( toilet ) , internal sanitary ( toilet ) , drinking water ( civil work ) , w / s for drinking water , cost of stainless steel handrail in stairs , cost of stainless steel handrail in corridors , cost of fire extinguisher , corridor marking , cost of reflector and anti skid nosing on staircase , cost of signage and general boards , supply, installation, testing & commissioning of lift ( 13 persons, 884 kg., 2 stops, 2 openings, car size 2000mm wide x 2400mm deep, ) as per specification attached etc. of orient, thyssenkrupp, johnson, otis, concourse or equivalent. , supply and fixing of structuralsteel frame ( such as tees, angles, channels etc ) & outer glazing with acp ( acp covering ) , each additional floor , providing and fixing of water cooler , providing of reception counter , supply and providing of wheel chair for disabled person at each floor , side table 1500*750*750mm with 3 drawer , reception chairs , bench ( stainless steel ) for blind , mess table for disabled , evacuation chairs to be available in every floor...

Uttar Pradesh Jal Nigam - Uttar Pradesh

32922299 supply of materials for various modification and renovation works under sugamya bharat abhiyan at sewayojan nideshalaya, lucknow. earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) , including dressing of sides and ramming of bottoms, lift upto 1.5 m, including gettingout the excavated soil and disposal of surplus excavated soil as directed, within alead of 50 m. all kinds of soil. , supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. , providing and laying in position cement concrete of specified grade excludingthe cost of centering and shuttering all work up to plinth level : 1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) : 8 graded stone aggregate 40 mmnominal size ) , centering and shuttering including strutting, propping etc. and removal of formfor foundations, footings, bases of columns, etc. for mass concrete , providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all workup to plinth level : 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) : 3 graded stone aggregate 20 mmnominal size ) , centering and shuttering including strutting, propping etc. and removal of formfor foundations, footings, bases of columns, etc. for mass concrete , brick work with common burnt clay f.p.s. ( non modular ) bricks of classdesignation 7.5 in foundation and plinth in: cement mortar 1:6 ( 1 cement : 6 coarse sand ) b / w in foundation , brick work with common burnt clay f.p.s. ( non modular ) bricks of classdesignation 7.5 in superstructure above plinth level up to floor v level in all shapesand sizes in : cement mortar 1:4 ( 1 cement : 4 coarse sand ) b / w up to plinth lvl. , steel reinforcement for r.c.c. work including straightening, cutting, bending, placingin position and binding all complete upto plinth level. thermo mechanically treated bars of grade fe 500d or more. , 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 ( 1 cement: 4 coarse sand ) , cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stoneaggregate ) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. , chequered precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cementslurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 10 mm thick bed of cement mortar 1:4 ( 1 cement: 4 coarse sand ) . ordinary cement without any pigment , providing and laying tactile tile ( for vision impaired persons as per standards ) of size 300x300x9.8mm having water absorption less than 0.5% and conforming to is: 15622, of approved make in all colors and shades in outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of engineer in charge. , providing and fixing stainless steel ( grade 304 ) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, i / c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer in charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. ) . , pathway marking , parking , civil work toilet , internal electrical toilet , internal sanitary toilet , drinking water ( civil work ) , w / s for drinking water , cost of stainless steel handrail in stairs , cost of stainless steel handrail in corridors , cost of fire extinguisher , corridor marking , cost of reflector and anti skid nosing on staircase , cost of signage and general boards , supply, installation, testing & commissioning of lift ( 13 persons, 884 kg., 2 stops, 2 openings, car size 2000mm wide x 2400mm deep, ) as per specification attached etc. of orient, thyssenkrupp, johnson, otis, concourse or equivalent. , supply and fixing of structuralsteel frame ( such as tees, angles, channels etc ) & outer glazing with acp ( acp covering ) . , providing and fixing of water cooler , providing of reception counter , supply and providing of wheel chair for disabled person at each floor , side table 1500*750*750mm with 3 drawer , reception chairs , bench ( stainless steel ) for blind , mess table for disabled , evacuation chairs to be available in every floor...

Varanasi Nagar Nigam - Uttar Pradesh

32877860 construction of cement concrete flooring ward no. 47 me kabeerchaura hospital ke pass shiv prasad gupt smarak se samudayik kendra tak wending zone hetu ...

North Central Railway - Uttar Pradesh

32798701 construction of new millwright office along with technical library, classroom and meeting room in jhsw. 2 ) up gradation of concrete flooring for keeping materials in gsd / jhs and all weather approach road. 3 ) construction of covered shed in front of receiving section amp c ward in gsd jhansi. 4 ) renovation of first floor meeting hall cum workstation, ground floor office and manifold office area of welding.1 ) construction of new millwright office along with technical library, classroom and meeting room in jhsw. 2 ) up gradation of concrete flooring for keeping materials in gsd / jhs and all weather approach road. 3 ) construction of covered shed in front of receiving section amp c ward in gsd jhansi. 4 ) renovation of first floor meeting hall cum workstation, ground floor office and manifold office area of welding., ...

Greater Noida Industrial Development Authority - Uttar Pradesh

32231417 remaining work of panchayat ghar near shiv mandir in village pali, greater noida remaining work of panchayat ghar near shiv mandir in village pali, greater noida , providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering all work upto plinth level: (cast in situ) , 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size). (dsr 13/4.1.8/p 85) , brick work with bricks of class designation 150 in superstructure above plinth level upto floor v level in all shapes and sizes in: , cement mortar 1:6 (1 cement : 6 coarse sand) (dsr 13/6.4.2/p 111) , providing and fixing 1mm thick m.s. sheet door with frame of 40x40x6mm angle iron and 3mm m.s. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. , using m.s. angles 40x40x6 mm for diagonal braces. (dsr 13/10.5.1/p 177) , steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. , in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works (dsr 13/10.25.2/p 180) , reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level, excluding cost of centring, shuttering, finishing and reinforcement: (cast in situ) , 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size) (dsr 13/5.2.2/p 96) , steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. , thermo mechanically treated bars/cold twisted bars. (dsr 13/5.22.6/p 99) , centring and shuttering including strutting, propping etc. and removal of form for: , suspended floors, roofs, landings,balconies and access platform. (dsr 13/5.9.3/p 97) , lintels, beams, plinth beams, girders, bressumers and cantilevers. (dsr 13/5.9.5/p 97) , 12mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand) (dsr 13/13.4.2/p 222) , 15mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement : 6 coarse sand) (dsr 13/13.5.2/p 222) , painting with synthetic enamel paint of approved brand and manufacture of requiredcolour to give an even shade: one or more coats on old work. (dsr 13/14.54.1/p 242) , finishing walls with water proofing cement paint of required shade: , old work (one or more coats applied @ 2.20 kg/10 sqm.) over priming coat of primer applied @ 0.80 ltrs./10sqm. complete including cost of priming coat (dsr 13/14.64.1/p 243) , cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. , 40mm thick with 20mm nominal size stone aggregate (dsr 13/11.3.1/p 186) , providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering all work upto plinth level: (cast in situ) , 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size). (dsr 13/4.1.3/p 85) , providing and fixing 1st quality ceramic glazed wall tiles conforming to is : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, inskirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (dsr 13/11.36/p 191) , providing and fixing g.i. pipes complete with g.i. fittings and clamps, including cuttings and making good the wall etc. internal work exposed on wall: , 15mm dia nominal bore (dsr 13/18.10.1/p 320) , providing and fixing g.i. pipes complete with g.i. fittings and clamps, including cuttings and making good the wall etc. internal work exposed on wall: , 20mm dia nominal bore (dsr 13/18.10.2/p 320) , providing and fixing g.i. pipes complete with g.i. fittings and clamps, including cuttings and making good the wall etc. internal work exposed on wall: , 25mm dia nominal bore (dsr 13/18.10.3/p 320) , providing and fixing brass bib cock of approved quality: , 15 mm nominal bore (dsr 13/18.15.1/p 321) , providing and placing on terrace (at all floor levels) polythylene water storage tank, isi : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (dsr 13/18.48/p 327) , providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10mm gap for thermal expansion, (i) single socketed pipes. , 110mm diameter (dsr 13/12.41.2/p 209) , providing and fixing m.s. holder bat clamps of approved design to sand cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), including cost of cutting holes and making good the walls etc.: , for 100mm dia pipe (dsr 13/17.37.1/p 292) , providing and fixing water closet squatting pan (indian type w.c. pan) with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: , white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests. (dsr 13/17.1.1/p 287) , providing and fixing 100mm sand cast iron grating for gully trap. (dsr 13/17.29/p 291) , providing and fixing wash basin with c.i. brackets, 15mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: , white vitreous china wash basin size 630x450 mm with a pair of 15mm c.p. brass pillar taps. (dsr 13/17.7.1/p 288) , kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of 1:4 cement mortar 1:4 (1 cement : 4 coarse sand). , 25mm thick. (dsr 13/11.26.1/p 190) , add labour cess @ 1% on all above items...

Uttar Pradesh Jal Nigam - Uttar Pradesh

32106832 water supply related work in nagar panchayat pachperwa, distt balrampur 1 construction of 1 no 300x150mm dia size, 440 / 400 m deep t.ws by dc rig machine & s.i.t.c of 800 lpm, 41 mtr head submersible pumping plants & chlorinating plant, voltage stabilizer, internal electrification of pump house, power connection and three month trail run etc, under pachperwa nagar panchayat water supply scheme indistrict balrampur 2 construction of 1 nos. 440 / 400 m deep tube wells for 800 lpm discharge with 300 x 150 mm dia size tube well assembly including supplying, fixing & lowering of housing pipe, riser pipe, as per iss: 4270 including m.s. sockets duly welded with m.s. ferro speed electrodes to have extra strength. tube well assembly containing of mserw housing pipe, plain / slotted pipe, m.s. reducer, m.s. bail plug. m.s. clamp, well cap, m.s. rings, etc. of desired size for potable drinking water confirming and completion of work as per instructions of engineer in charge work specification conferming toiss: 2800 ( part 1 & 2 ) 1979. bore logging will be done by electric logger beforelowering of t.w. assembly. 3 transportation, errection and dismantaling of rig machine and camp equipages. 4 drilling of bore by 600mm from gl to 50 m 5 drilling of 500 mm. dia bore from 50 m to100 m. bgl 6 drilling of 500 mm. dia. bore from 100 mbgl to 200 m. bgl 7 drilling of 500 mm. dia. bore from 200 mbgl to 300 m. bgl 8 drilling of 500 mm. dia. bore from 300 mbgl to 440 m. bgl 9 logging of bore hole and testing 10 supply & lowering of 300mm mserw 7.1 mm thick housing pipe including accessories, welded by ferrospeed rod from gl to 45 m bgl 11 supply & lowering of 150mm mserw 7.1 mm thick plain pipe including accessories, welded by ferrospeed rod from 45 m bgl to 400 m bgl 12 supply & lowering of 150mm mserw 7.1 mm thick slotted pipe including accessories, welded by ferrospeed rod from 45 m bgl to 400 m bgl 13 m.s. fitting such as clamps, bail plug, reducer, well cap, girder & support structure 14 supply & shrouding of lal kuwan pea gravel of 1.6 4.8 mm size. ( as per is:4097 1988 ) or as per requirement. 15 lowering of tube well assembly duly welded including welding electrode and shrouding of pea gravel complete in all respect. 16 300 mm. dia. housing pipe from g.l to45 m. bgl 17 150 mm. dia plain / slotted pipe 45 m. bglto 100 m. bgl 18 150 mm. dia plain / slotted pipe 100m. bgl to 200 m. bgl 19 150 mm. dia plain / slotted pipe 200m. bgl to 300 m. bgl 20 150 mm. dia plain / slotted pipe 300m. bgl to 400 m. bgl 21 transportation, erection and dismantaling of 600 psi air compressor and its camp equipages. 22 development of tubewell by 600 psi air compressor for 60 hrs / as per required site condition. 23 transportation, erection and dismantaling of o.p. unit and its camp equipages. 24 development of tubewell by o.p. unit for 100hrs / as per required site condition. 25 chemical test of water sample 26 clear water submersible pumpng plant 800 lpm, 41 meter head chlorinating plant and automatic servo voltage stabilizer. 27 sitc of clear water submersible pump complete with electric motorcapable to operate on 380 / 420 volts 3 phase 50 c / s a.c. supply of 800 lpm, 41 mtr head and automatic star delta starter 12.5 h.p. 28 sitc of 100 mm dia 5.4 mm thick m.s. main piping and valves with 24 mtr column pipe, electromechanical type chlorinating plant, power wiring, double earthing, painting of pumping plant with anticorrosive black paint, special tools spanners and electric rubber sheet, 6.5 point wiring of pump house ( intrnal and external ) , 2 t capacity chainpulley block tested on 3 ton load with 4.5 m lift, spur geared, gauges and fittings complete in all respect with all required material t&p labour etc complete for t / w no. 1 & t / w no. 2 29 automatic servo voltage stablizer having capacity 20 kva fully copper winding three phase a.c. supply 50 hz input voltage 90 500 output voltage 400 volt ± 1% with transformar oil, casting wire & power cable and earthing its complete in allrespect. 30 trial & run of above aquipment for 3 months 31 o.h.t. raelated works. 32 supply and fixing of water level indicator includingsupply of all labour, material, t&p etc. complete in all respect. 33 provision forpainting work & repairing of railing of oht 800kl. / 19m. o.h.t. including supply of all labour, material, t&p etc. complete in all respect. 34 provision forrepairing of septage, inlet / outlet pipe including supply of all labour, material, t&p etc. complete in all respect. 35 25 mm thick ( 1:2:4 ) plain cement concrete floor with cement course sand and 20 mm gauge approved stone grit, laid in panels, finished with 3 mm floating coat of neat cement or cement and marble dust in ratio of 1:5 as specified over and including 75 mm thick base concrete consisting of cement, local sand and 40 mm gauge first class brick ballast in the proportion of 1:4:8 and removing any overlapping of mortar at the joints of panels if any and given them uniform finish including supply of all materials, labour t&p etc required for proper completion of work. 36 construction of masonary type sluice valve chamber as per departmental type design. including supply of all labour, material, t&p etc. complete in all respect. 37 pump house related works. 38 excavation of earth in foundation in ordinary soil ( loan, clay or sand ) including lift up to 1.50m and leap up to 50.00 m refilling of excavated earth in to space between building and sides of foundation trench, watering, ramming and disposal of surplus earth up to 50 m from the center of the trench. 39 concrete with 40 mm gauge first class brick ballast, local sand and cement in proportion of 1:6:12 in foundation and floors including supply of all materials, labour, t&p etc required for proper completion of work. 40 first class brick work in 1:6 cement and local sand mortar in foundation and plinth including supply of all materials, labour t&p etc required for proper completion of work. 41 25 mm thick damp proof coarse with cement , stone grit 12mm and approved coarse sand 1:1.5:3 with and including water proofing materials asordered by the engineer incharge in the proportion as specified by the manufactures, also included bitume painting ( 85 / 50 or 85 / 25 ) , supply of all materials, labour t&pand tools and plants etc required for proper completion of the work and including proper curing and shuttering as necessary. 42 first class brick work in 1:4 cement and local sand mortar in super structure including supply of all materials labour t&p etc required for proper completion of work. 43 r.c.c. work with cement approved coarse sand and 20 mm gauge approved stone ballast in the proportion 1:2:4 in lintels of doors, windows & sunshade excluding reinforcement and its bending but including its fixing and binding the same 24 b wg wire in position with supply all materials labour t&p etc required for proper completion of work. 44 as in item no. 6 above but for slab 45 supply and fix angle iron door chaukhat of size 50mm x 50mm x 6 mm including supply of all materials labour t&p etc required for proper completion of work. door frames / window frame. 46 mild steel or plain work such as reinforced concrete or reinforced brick work wrought to required shape as necessary including building for proper completion of work and including supply of steel its wastage bend hooks and authorized over lapping shall be measured floor tow level 47 25 mm thick ( 1:2:4 ) plain cement concrete floor with cement course sand and 20 mm gauge approved stone grit, laid in panels, finished with 3 mm floating coat of neat cement or cement and marble dust in ratio of 1:5 as specified over and including 75 mm thick base concrete consisting of cement, local sand and 40 mm gauge first class brick ballast in the proportion of 1:4:8 and removing any overlapping of mortar at the joints of panels if any and given them uniform finish including supply of all materials, labour t&p etc required for proper completion of work. 48 40 mm thick cement concrete flooring 1:2:4 laid in one layer finished with a floating coat of neat cement without base concrete. 49 supply and fixing of r.c.c. cover of size 0.80 x 0.80 meter over pump house slab opening including supply of all material labour t&p etc complete. 50 supply of 40 mm thick sheesham wood door / window shutters with 9 mm thick plywood or pressed wood pannels and fixing cleats, stops, hinges, locks, bolts, handlers , spring and other fittings ( excluding suply of fittings ) 51 supply of oxidized iron fittings of approved make for doors and window. 52 12 mm thick plaster with cement and local sand mortar in proportion of 1:4 over brickwork, minimum thickness not be less than 10 mm including supply of all materials labour, t&p etc required for proper completion of work. 53 11.5 cm string or drip coarse in1:6 cement and local sand mortor 54 painting or varnishing new iron work in small areas or new wood work with one priming coat and two coats of approved paints or varnish including supply of all materials labour, t&p etc required for proper completion of work. 55 white cement in three coats including supply of all materials labour, t&p etc required for proper completion of work. 56 providing plaster of paris wallputty of 2mm thickness over plastered surface to prepare the surface even and smooth complete. 57 distempering ( two coat ) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as berger, j&n, shalimar, asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. 58 supply and fixing of rolled steel joist including cost of all materials labour, t&p etc complete. 59 provide and fixing of r.c.c. pre cast ventilators jali over opening including supply of all materials labour, t&p etc complete. 60 supply and fixing of 110 mm dia pvc rain water down pipe with clamp etc. 61 staff quarter & boundary wall painting work. 62 finishing walls with oil based distemper paint of approved make and quality over one priming on new work with two coats to given an even shade including supply of all materials, labour t&p etc required for proper completion of work. for staff quarter & boundary wall. 63 construction of approach road & related works. 64 first class brick work in 1:4 cement and local sand mortar for brick edging including supply of all materials labour t&p etc required for proper completion of work. 65 concrete with 40 mm gauge first class brick ballast, local sand and cement in proportion of 1:6:12 in foundation and floors including supply of all materials, labour, t&p etc required for proper completion of work. 66 laying of c.c. road slab 100mm thick in ( 1:2:4 ) cement, coarse sand and stone ballast over prepared surfaceincluding supply of all materials, labour, t&p etc required for proper completion of work. 67 rising main & appurtenant work. 68 supply of following materials including at f.o.r. destinationinclusive of all taxes & duties, third party inspection charges, transit insurance, freight, loding, unloding and stacking etc complete. 69 isi marked d.i. class k 7 pipes conforming to is 8329 / 2000 or its latest amendments with isi markedrubber gasket. 70 150mm dia 71 isi marked c.i.d.f. sluice valve, class 1 conforming to is 780 / 1969 or its latest amendments. 150mm 72 i.s.i. mark d.i. specials. 73 excavation for pipe line in ordinary soil ( loam, clay, sand ) and soil mixed with kankar, shingle, moorum etc. requiring the use of special t&p such as pick axes, sabblas with lift up to 1.5m and lead up to 50m and including filling back, watering and ramming of excavated earth into the trenches and disposal of surplus earth within 50 metres. 74 cartage of following pipes and special from local store to site of work , lowering them into the trenches and laying true to alignment and gradient, jounting of pipes, cutting of pipes for making the required length including testing of d.i. pipe k 7 150mm dia 75 fixing of sluice valve in position in the pipe line and jointing including the cost of all jointing materials, testing etc. for proper completion of the work.c.i. d / f sluice valves 150mm 76 supply all materials, labour, t&p etc. and construct the masonary type chambers as per type design for sluice valves 77 r.c.c. with cement, coarse sand and 20mm gauge stone ballast in proportion of 1:1.5:3 for thrust block of pipe line excluding supply of reinforcement and its bending but including its fixing and binding the same with 0.50 mm thick binding wire in position and necessary centering and shuttering including cutting and supply of all materials, labour, t&p etc. required for proper completion of the work. ( excluding cost of steel required ) 78 mild steel or iton work in r.c.c. wrought to required shape as necessary bending for proper completion of the work including supply of steel & wastage etc....

Firozabad Municipal Corporation - Uttar Pradesh

32010314 tender for item rate tender for civil work 2 earth work in cutting and cartage up to 8 k.m with all complete ( item no. 251+253 ( d ) +253 ( e ) 3 earth work in filling ordinary soil ……… all complete. ( as per analysis ) 4 sand filling in plinth including ………… all complete. ( item no. 255 ) 5 p / l cement concrete in 1:6:12 etc………… all complete. ( dsr pwd si no. 273 ) 6 p / l cement concrete in 1:5:10 etc………… all complete. ( dsr pwd si no. 274 ) 7 p / l cement concrete in 1:2:4 etc………… all complete. ( dsr pwd si no. 4.1 ) 8 p / l cement concrete in 1:1.5:3 etc………… all complete. ( dsr pwd si no. 4.1 ) 9 rcc work p / l in position specified grade of reinforced cemet concrete in 1:2:4 etc……… all complete. ( dsr / pwd si no. 5.1 ) 10 rcc work p / l in position specifled grade of reinforced cement concrete in raft foundation in 1.1.5.3 etc……. all complete. ( dsr / pwd si no. 5.1 ) 11 m 150 class brick work on 1:4 cement and fine sand mortor with all complete. ( dsr si.no. 6.1 ) 12 m 150 class brick work on 1:6 cement and fine sand mortor with all complete. ( dsr si.no. 6.1 ) 13 m 150 class brick work on 1:3 cement and fine sand mortor with all complete. ( dsr si.no. 6.8 ) 14 2 cm thick d.p.c with cement and approved coarse sand 1:2 etc……….. all complete. ( dsr pwd si. no. 360 ) 15 32 mm thick supply and fixing of flush doors etc……… all complete. ( pwd / dsr si no. 470 ) 16 providing & fixing 1.00 mm thick decorative high pressure laminated sheet of plain wood grain in gloss etc……… all complete. ( pwd / dsr si no. 9.127 ) 17 mild steel and iron work of small size etc……… all complete. ( pwd / dsr si no. 502 ) 18 mild steel and iron work of heavy size etc……… all complete. ( pwd / dsr si no. 503 ) 19 mild steel or iron work in plain work etc……… all complete. ( as per analyisis ) 20 providing and fixing stainless steel ( grade 304 ) etc……… all complete. ( pwd / dsr si no. new ) 21 providing and fixing stainless steel ( grade 202 ) etc……… all complete. ( pwd / dsr si no. new ) 22 providing of 1.00 mm thick with zine coating not less then 275 gm / sqm corrugated g.s sheet roofing including vertical. / curved surface fixed with ploymerr coatedetc……… all complete. ( pwd / dsr si no. 12.1 ) 23 providing and fixing on wall face unplasticised rigid pvc rain water pipers conforming etc……… all complete. ( pwd / dsr si no. 12.41 ) 24 12 mm thick plastering work on 1:3 cement and course sand mortor with all comoplete. ( pwd dsr si no. 13.9 ) 25 12 mm thick plastering work on 1:4 cement and course sand mortor with all comoplete. ( pwd dsr si no. 13.4 ) 26 12 mm thick plastering work on 1:6 cement and course sand mortor with all comoplete. ( pwd dsr si no. 13.4 ) 27 making grooves 10 to 12 mm wide x 8mm deep in plaster of the wall or in celling vertically or horizontally as required. ( pwd dsr si no. 598 ( 1 ) . 28 repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters etc………… all complete. with cement mortal 1:4 ( 1 cement : 4 fine sand ) ( pwd dsr si no. 14.1 ) 29 cement concrete flooring 1:2:4 ( 40 mm thick floor ) etc ………. all complete. ( pwd dsr si no. 665 ) 30 supply & laying tack coat of bitumin @1 / 4kg per sqm with all complete 31 providing and layingbm 50mm thick compacted with hmp &pavour finisher with all comp. 32 providing and layingsdbc 25mm thick compacted with hmp &pavour finisher with all comp. 33 providing and fixing 18 mm thick granite ( gang saw cut ) , 20 mm thick base cement morrtal 1:4etc……….. all complete. ( pwd / dsr si no. 11.23 ) 34 providing and laying ceramic glazed floor tiles of size 300x300 mm etc ……… all complete. ( pwd / dsr si no. 11.37 ) 35 providing and laying vitrified tiles in floor with lean concrete of 500x500 sizes ( thickness 10mm ) etc …………. all cmomplete. ( pwd / dsr si no. 11.27a ) 36 providing and fixing 2.2 cm deptth glass strips of 4 mm thick in joints of floor etc……….. all complete. ( pwd / dsr si no. 11.27a ) 37 s / f chequerred precast cement concrete tiles 22 mm thick in footpath 20 mm thick bed of cement mortar 1:4 including preparation of 50 mm thick base with concrete 1:4:8 40 mm b / b complete. ( pwd / dsr si no. 11.2 ) 38 applying priming coat over steel and other metal surface up to 10 cm etc ……. all complete. ( pwd / dsr si no. new 641 ) 39 applying priming coat new wood surface up to 10 cm etc ……. all complete. ( pwd / dsr si no. 19.61 ) 40 painting 1st coat over priming coat on steel and otherr metal surface up to 10 cm etc …………. all complete ( pwd / dsr si no. 19.29 ) 41 painting 1st coat over priming coat on new wood surface up to 10 cm etc …………. all complete ( pwd / dsr si no. 19.29 ) 42 distempering ( first coat ) with oil bound distemeper of approved brand etc …………. all complete ( pwd / dsr si no. 649 ) 43 removing oil paint or varnish from steel and other metal surface of from wood based surface etc …………. all complete ( pwd / dsr si no. 657 ) 44 finishing walls with water proofing cement paint of approved mak such as super snowcem durocem, robiance, guttucem, supercem quality and of required etc …………. all complete ( pwd / dsr si no. 660 ) 45 finishing walls with sandlex matt. coat over a priming coat of water proof cement paintetc …………. all complete ( pwd / dsr si no. new ) 46 well painting ( one coat ) with plastic emulsion pain of approved brand etc ……….. all complete. ( pwd / dsr si no. 18.58 ) 47 finishing walls with putty approved brand and etc ……….. all complete. ( pwd / dsr si no. new ) 48 finishing walls with textured exterior paint approved brand and etc ……….. all complete. ( pwd / dsr si no. new ) 49 dismeantling brick work or stone work in lime or cement etc ……….. all complete. ( pwd si no. 692 ) 50 dismeantling reinforced cement of reinforced brick worrk including stacking etc ……….. all complete. ( pwd si no. 694 ) 51 dismeantling cement concrete or brick or granolithic floors includingg etc ……….. all complete. ( pwd si no. 697 ) 52 dismeantling existing plaster including disposal of refuse as directed etc ……….. all complete. ( pwd si no. 706 ) 53 scrapping old white or colour wash includingetc ……….. all complete. ( pwd si no. 708 ) 54 dismentaliing of b.o.e soling / inter locking tiles stacking etc ……….. all complete. ( pwd si no. new ) 55 red sand stone work for wall lining etc. 30 mm thick in 1:3 etc …….. all complet. ( pwd / dsr si no. 7.23 ) 56 construction of granular sub base ( gsb ) etc………. all complee. ( ase per analysis ) 57 consolidation of 45 63 mm and 22.4 53 mm gauge stone ballast 10 cm thick etc………. all complete. ( ase per analysis ) 58 brick soling with straight over burnt brick laid flat and dry brick edging on both side including etc………. all complete. sch pwd no. 762 ( b ) 59 supply and laying of i shaped precast 80 mm ( ordinary grey ) interlocking tiles etc………. all complete. sch pwd no. new 60 supply and laying of i shaped precast 80 mm ( ordinary coloured ) interlocking tiles etc………. all complete. sch pwd no. new 61 supply and laying of i shaped precast 80 mm ( rubber molded ) interlocking tiles etc………. all complete. sch pwd no. new 62 constructing brick masonry manhole etc………… all complete. inside size 900x800 mm and 500 mm deep including c.i cover frame ( dsr si no. 19.7 ) 63 constructing brick masonry chamber for underground c.i inspection chamber and bendsetc………… all complete. inside dimensions 455x610 mm and 45 cm deep for single pipe : with common burnt clay f.p.s ( non modular ) brick of class designation m 150 ( dsr si no. 19.30 ) 64 providing & fixing of vertical garden at site of work i / c fixing of m.s square pipe of ( 5.50x5.50 ) of 12 guage approx weight of pipe @ 18 kg per 6mtr length for frame and horizontal support for fixing fo module @50cm c / c fo pipe ( 5.5mm*2.5mm ) of 12 guage thickness approx weight 12kg per 6 mtr lenght2mm thick m.s sheet water storage tank on the tank 50 cm molding at per site requirement all complete. with applying of antirust paint and after antirust paint all frame and tank will be apinted with two coated of black japan paint all complete as per standard design with vertical module of size ( 50cmx18cm ) of r.s oe / r equivlent paint with drip irrigation system with timer and 50 mm dia inlet water supply system all complete.as per approved design. after that each planter cup inside covered by geotextile cloth of 250 gsm in bottom and further fillup 1:2 ratio with coco pit and soil rite mixture complete for plantation of each planter cup. the plantation of plants such as money plant ( variegated, gree, golden ) syngoium ( butterfly, pink, white ) , dracena ( song of india, variegated, compacta ) , , aspharagus ( spengrii, marie ) , chlorophytum, etc the foundation of frame for each vertical support ( 50cmx50xcmx50cm ) in cement concrete1:2:4 all complete as per direction of officer in charge. 65 complete. maintanance of vertical garden with supply of water through water tanker including resetting / displaying fo vertical garden including watering through drip irrigation, cleaning / replacement of dripper. replacement of casuality plants with fresh plants change of pot pattren after 15 days interval or as per requirement of site with complete t&p provide by the contractor. the cost of casaulity of plants 25% as natural casuality for the first three year and also refilling of cup inside covered by geitextile cloth of 250 gsm in bottom and further fillup 1:2 with coco pit and soil rite mixture all complte as per direction of officer in charge nothing shall be paid extra for three years. 66 relaying of old 80 mm thick i shaped & zig zag shapedinter locking tiles including 30 mm thick local sand base levelling and dressing of surface required level and slope, filling joints with local sand all complete. ( as per analysis of rate ) 67 cartage of earth or malva from 8km distance………. complete. 68 proving and fixing pvc pipe conforming to is make working pressure 4kg / sqcm including testing labour t&p and all complete fittings75mm diameter 69 proving and fixing pvc pipe conforming to is make working pressure 4kg / sqcm including testing labour t&p and all complete fittings90mm diameter 70 proving and fixing pvc pipe conforming to is make working pressure 4kg / sqcm including testing labour t&p and all complete fittings110mm diameter 71 proving and fixing pvc pipe conforming to is make working pressure 4kg / sqcm including testing labour t&p and all complete fittings140mm diameter 72 material 73 supply of m150 class bricks 74 supply of fine sand . 75 supply ofcourse sand . 76 supply ofstone grite 20mm gauge . 77 supply ofstone grite 10mm gauge . 78 supply of ordinary portland cement ( j.p, a.c.c, birla, j.k or equivalent ) opc 79 supply ofppc cement ( j.p, a.c.c, birla, j.k or equivalent ) 80 supply of 80 mm thick c.c interlocking tiles ( gray ) with all complete. ( sor no. 8 ) 81 supply of 80 mm thick interlocking tiles ( coloured rubber moulded ) with all complete. ( pwd. 4 ( a ) 82 supply of 100 mm thick interlocking tiles ( grey ) with all complete. ( pwd. 4 ( a ) 83 providing and laying of hot applied thermoplastic comound 2.5 mm thik including ………. all complete. ( pwd. si. no.24 chapter no. 20 ) 84 supply gsb. ( as per anaylisis ) 85 supply ofstone dust. 86 head load per chainges ( 30m / cum ) 87 supply of red sand stone 88 supply of r.c.c main hole cover 89 supply of r.c.c main hole ring 90 supply of m.s iron tmt bar 8 mm dia 91 supply of m.s iron tmt bar 10 mm dia 92 supply of m.s iron tmt bar 10 mm dia 93 supply of r.c.c 900x450x100 mm ( pre cast ) 94 supply of r.c.c 1200x450x100 mm ( pre cast ) 95 supply of r.c.c 1500x450x100 mm ( pre cast ) 96 600 dia manhole cover ( pre cast ) 97 supply of j hooks. 98 supply of g.i barbed wire ( hot dip ) 99 supply of ballies ( 100mm average dia ) 100 supply of water proofing compound ( dr fixit ) 101 supply oftraffic cones 102 pvc low level cisterns 10 litre capacity with all internal fitting perryware, cert, last etc. 103 internal fitting for pvc low level cisterm 104 proving and fixing water closet squatting pan ( india type wcpan ) all complete. 105 proving and fixing white vitreous china pedestal typewater closet ( european type wcpan ) all complete. 106 proving and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with all complete. 107 proving and fixing white vitreous china wash besin size 550x400 mm with………………………..all complete. 108 proving and fixing white vitreous china squatting plate urinal with internal rim longitudinal flush pipe. 109 proving and fixing white vitreous china wash besin including making all connections but excluding cost of fittings. ( flat back wash basin of size 450x300 ) 110 proving and fixing mirror of superior glass of appd quality all complete. ( rectangular shape 453x357mm ) 111 supply of bib cock 112 supply of c.p stop cock 113 supply of piller cock 114 labour 115 mistri 116 mason ( for floor & tites work ) 117 painter ( for polishing work ) 118 painter ( for painting work ) 119 mazdoor 120 gardener...

North Central Railway - Uttar Pradesh

31851086 supply of 1 ) cmlr jhansi infrastructure facilities for ss 2 ( poh ) schedule for lhb coaches. 2 ) gsd / jhs up gradation of concrete flooring for keeping materials gsd / jhs and all weather approach road. 3 ) jhs ( cmlr ) :infrastructure facilities required for poh. 4 ) roof top rain water harvesting at rsk / stli...

Directorate Of Industries - Uttar Pradesh

30770869 bids are invited for boqauto extension if any seller submits price in last 15 minutes, the rawill be auto extended by 15 minutes. ( a maximum of100 times ) average turn over of last 3 years 12 lakh ( s ) mse total quantity : 1 1 earth work in excavation by mechanical means ( hydraulic excavator ) / manual meansover areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) ias per bid pdf document 2 extra for levelling & neatly dressing of disposed soil completely as directed by engineer in charge.footing 1 footing 2 footing 3 3 1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) : 8 graded stone aggregate 40 mm nominal size ) footing 1 & footing 2 footing 3 4 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) : 3 graded stone aggregate 20 mm nominal size ) as per bid pdf document 5 reinforced cement concrete work in walls ( any thickness ) , as per bid pdf document 6 centering and shuttering including strutting, propping etc. as per bid pdf document 7 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in as per bid pdf document 8 12 mm cement plaster of mix : 1:4 ( 1 cement: 4 fine sand ) 9 cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate ) finished with a floating coat of neat cement, as per bid pdf document 10 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.as per bid pdf document 11 sheet gi, cladding sheet, roof sheet, 12 ms structure, ms column and structure...

Small Scale Industries Development Corp. Ltd. - Uttar Pradesh

30591824 bids are invited for earth work in excavation by mechanical means ( hydraulic excavator ) / manual meansover areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) ias per bid pdf document as per bid pdf document , extra for levelling & neatly dressing of disposed soil completely as directed by engineer in charge.footing 1footing 2 footing 3 as per bid pdf document , 1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) : 8 graded stone aggregate 40 mm nominal size ) footing 1 & footing 2 footing 3 as per bid pdf document , 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) : 3 graded stone aggregate 20 mm nominal size ) as per bid pdf document as per bid pdf document , reinforced cement concrete work in walls ( any thickness ) , as per bid pdf document as per bid pdf document , centering and shuttering including strutting, propping etc. as per bid pdf document as per bid pdf document , brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in as per bid pdf document as per bid pdf document , 12 mm cement plaster of mix : 1:4 ( 1 cement: 4 fine sand ) as per bid pdf document , cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate ) finished with a floating coat of neat cement, as per bid pdf document as per bid pdf document , steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.as per bid pdf document as per bid pdf document , sheet gi, cladding sheet, roof sheet, as per bid pdf document , ms structure, ms column and structure as per bid pdf document total quantity : 1...

Uttar Pradesh Small Industries Corporation Limited - Uttar Pradesh

30225404 tender for e / w in excavation in trenches for foundation pipes cable etc in ordinary soil l / c lift upto 1.5 m.lead upto 50 m. and dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed by e / i within need of 50 m. si no.251 2 earth in cutting or in embankment in ordinary soil excavation to be done from of regular pits not exceeding / 2m. in depth and work embankment to be in 20 cm. layers including ramming and dressing the surface to required levels and slopes and also including 1.5 m lift and 30 m.lead the earth from cutting to be used in marking embankment or to be deposited as spoil banks within 2 km distance as directed by the engineer in charge. ( 253 a ) 3 p / l of cement concrete 1:6:12: ( 1 cement: 6 fine sand : 12 graded stone aggregate 40 mm nominal size ) and curing complete i / c cost formwork in foundation and floors as per si. no.281. 4 r.c.c work with cement, approved coarse sand & 2cm gauge approved stone grit in proportion of 1:2:4 in raft foundation and flootingcutting and bending , but including its fixing and binding the same with 24 b.w.g.g.i. binding wire and including necessary centring and shuttering etc. and supply of all materials, labour, tools & plants etc. required for proper completion of the work including cost of binding wire.si.no.287 5 m 150 class brick work in 1:6 cement & fine sand mortor in foundation per si.no. 303 6 r.c.c work with cement, approved coarse sand & 2cm gauge approved stone grit in proportion of 1:2:4 in lighter beams cutting and bending , but including its fixing and binding the same with 24 b.w.g.g.i. binding wire and including necessary centring and shuttering etc. and supply of all materials, labour, tools & plants etc. required for proper completion of the work including cost of binding wire.si.no.285 7 r.c.c work with cement, approved coarse sand & 2cm gauge approved stone grit in proportion of 1:2:4 in column cutting and bending , but including its fixing and binding the same with 24 b.w.g.g.i. binding wire and including necessary centring and shuttering etc. and supply of all materials, labour, tools & plants etc. required for proper completion of the work including cost of binding wire.si.no.288 8 m.s ( tor steel or plain ) in plain work such as r.c.c or r.b work including cutting / bending for proper shape as necessary including supply of all steel & wastage , bend , hook & authorised overlapping shall be measured … complete item. ( a / r ) 9 class m150 class brick work in 1:4 cement & fine sand mortor in super structure as per s.l no.305+309 10 12 mm cement plaster thick 1:4 cement & fine sand fair side single &half brick wall including internal rounded angles not exceeding 80 mm in grith & finished even and smooth si.no.17.58 11 mild steel or iron work of small size and sections such as holding down bolts, hold fast tie rods grating etc ( when not included in an overall rates ) wrought to required shape as necessary for bending etc. including supply of steel and its wastage including grinding and making holes as required for completion of work. ( ii ) fabrication of grill / stairs case railing. 12 providing and applying white cement based putty of average thickness of1mm of approved brand and manufacturer over the plasterd wall surface even and smooth including cost of material labour and t&p complete. dsr 13.8 13 finishing walls with two coat of acrylic smooth exterior paint of best quality including supply of all material labour and t&p etc.required for proper completion of the work. dsr 13.46.1 14 painting or varnishing on iron works in small areas or new wood work with one coat of ready mixed priming paint & one coat of approved superior quality ready mixed paint of clear synthic varnish including supply of all materials labour and t&p etc.required for proper completion of thework paint to be used should confirm to the i.s.i no.103 1950 si.no 641+642 15 25 mm cement concrete flooring 1:2:4 by laid ovcer base concrete finished with floating coat of neat cement including fixing of glass strip. si.no. 14.69 16 construction of granular sub base by providing well graded material spreading in uniform layers with motor grader on prepared surface, mixing by mix place method as per clause 402 17 providing and laying of interlocking concrete block pavement with 80 mm thick icbp having strenth not less than30 kn / m2 complete as per technical specificatation clause1500 18 s / f of rcc chair. 19 s / f of 4x2.5 feet size granite stone at siteincluding writing painting with graving and cartage up to site complete / 20 s / f of steeel tubuler pole 9.5 mtr long designated 410 sp 39 in 1:3:6 cement concrete foundation including excavation back filling etc comp. in all respect. ( sch no. 619 ) 21 painting of the electric pole with 2 coats of aluminium paint over red oxide primer .complete in all res. ( sch.no. 634 ) 22 cables.s / l of alluminium conducter p.v.c insulated armoond served sheated 10sqmm 2 core cable complete in all respect. ( sch no 501 ) b 23 s / f of brass of nickle plated compression glandinsulated with tape and making connection etc.complete in all res. ( sch.no.503 b ) 24 s / f of plann or pipe type coppper tin plated cable leads. insulated with tape and making connection etc.complete in all res. ( sch.no.504 c ) 25 supply & fixing of ring pipe steel frame 3 no.l.e.d lighr in all respect………...…..complete.market rate 26 s / l with 4 no. wire for 4 sqmm pvc insulated1100v grade singelcopper conductor with complete in all respect , sch no.289 c 27 supply & burying og 600mmx600mmx6mmg.i plateearthing complete. ( sch.no.702 ) 28 s / f of 63 amp 415 v tpmain switch bord…. complate sch no 323 29 s / f ofled flood lighting having die cast alluminium body and diffuser / reflector with driver set suitable for 140 to 150watt confirming toi.p 66 protection and above protection. compleate in all respect. ( sch. no. 1454 ) 30 s / f of 20mm dia flexible pipe. complate....

Uttar Pradesh Rajya Vidyut Utpadan Nigam Limited - Uttar Pradesh

29100158 miscellaneous civil works in power house at ptpp parichha earth work in excavation all kind of soil by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30cm in depth 1.5m in width as well as 10 sqm on plan ) including disposal of excavated earth, lead up to 50m and lift up to 1.5m disposed earth to be levelled and neatly dressed.all kind of soil. 2 supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 3 surface dressing of the ground in all kind of soil including removing vegetation and in equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m 4 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level: 1:4:8 ( 1 cement: 4 coarse sand :8 graded stone aggregate 40 mm nominal size ) . 5 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level: 1:2:4 ( 1 cement: 2 coarse sand :4 graded stone aggregate 20 mm nominal size ) . 6 reinforced cement concrete work in walls ( any thickness ) , including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level excluding cost of centering, shuttering, finishing and reinforcement: 1:1.5:3 ( 1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size ) 7 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level :thermo mechanically treated bars of grade fe 500d or more. 8 structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 9 as above item no. 8 but steel shall be issued by the department free of cost. 10 brick work with fly ash bricks ( non modular ) of class designation 7.5 in foundation and plinth in: cement mortar 1:6 ( 1 cement : 6 coarse sand ) 11 half brick masonry with non modular fly ash bricks of class designation 10, conforming to is : 12894, in super structure above plinth and upto floor v level : ement mortar 1 : 3 ( 1 cement : 3 coarse sand ) 12 brick work with clay flyash f.p.s. ( non modular ) brick of class designation7.5 in superstructureabove plinth level up to floor five level in : cement mortar 1:6 ( 1 cement : 6 coarse sand ) 13 centering and shuttering including strutting, propping etc. and removal of form for : 14 foundations, footings, bases of columns, etc. for mass concrete 15 lintels, beams, plinth beams, girders, bressumers and cantilevers 16 columns, pillars, piers, abutments, posts and struts 17 random rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 ( 1 cement : 6 coarse sand :12 graded stone aggregate 20 mm nominal size ) at plinth level with: cement mortar 1:6 ( 1 cement : 6 coarse sand ) 18 12 mm cement plaster of mix 1:6 ( 1 cement : 6 coarse sand ) 19 extra for providing and mixing water proofing material in cement concrete work @ 1 kg per 50 kg of cement. 20 neat cement punning. ( 6mm plaster ) 21 cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate ) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete:40 mm thick with 20 nominal size stone aggregate. 22 providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position: sal wood. 23 clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared. 24 providing corrugated g.s. sheet roofing including vertical / curved surface fixed with polymer coated j or l hooks, bolts and nuts 8 mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces ) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required:0.80 mm thick with zinc coating not less than 275 gm / m2 25 providing ridges or hips of width 60 cm over all width plain g.s. sheet fixed with polymer coated j, or l hooks, bolts and nuts 8 mm dia.. g.i. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gm / m2 26 providing and fixing 1mm thick m.s. sheet door with frame of 40x40x6mm angle iron and 3mm m.s. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.using m.s. angles 40x40x6mm for diagonal braces. 27 providing and fixing double action hydraulic floor spring of approved brand and manufacture is : 6315 marked, for doors including coast of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece m.s. sheet outer box with slide plate etc. complete as per the direction of engineer in charge.with stainless steel cover plate. 28 prefixing old glass panes with putty and nails. 29 providing & fixing fully glazed anodized aluminum fixed glazing with hindalco or equivalent extruded standard sections of various thickness show in extruded standard sections of various thickness shown in drawing joints mitered and jointed as shown in drawing including providing and fixed of 5.5 mm thick glass with neoprene beading all round. the minimum thickness of anodizing on all aluminum sections should be 20 micron with a ( + ) 2 microns tolerance. the rate should include the cost of fixing of all frame to teak wood frame or with masonry / rb / rcc structure by there of starting from 100 mm above the bottom in vertical member excluding cost of teak wood frame. but including cost of all other materials, labour t&p etc. complete required for proper completion of work. 30 same as item above but for openable window portion as shown in drawings, including providing & fixing aluminum hinges of heavy quality and all other fitting like concealed tower bolts handles etc. as per direction of engineer in charge required for proper completion of work. 31 same as item above but for openable gate / doors portion as shown in drawings including providing and fixing pivots of heavy quality and all other fittings like concealed approved tower bolts, bush plate ( as shown in drawing ) and approved standard brass body with brass components 6 levers heavy duly concealed lock etc. required for proper completion of work. 32 renewing glass panes, with putty and nails wherever necessary: float glass panes of thickness 5.5 mm. 33 carriage of material by mechanical transport including, loading, unloading and stacking up to 2 km:earth, building rubbish etc . ( rate applicable after deduction of void as per cpwd / pwd norms ) 34 providing and laying 60 mm thick factory made cement concrete interlocking pavers block of m 30 grade made by block making machine with strong vibratory compaction and of approved size and design / shape laid in required color and pattern over and including 50 mm thick compacted bed of course sand, filling the joints with coarse sand etc. all complete as per the direction of engineer in charge. 35 providing and fixing lst quality ceramic glazed wall tiles conforming to is : 15622 ( thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement :3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 36 providing and laying polished vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorptions less than 0.08% and conforming to is : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) including grouting the joints with white cement and matching pigments etc. complete: size of tile 60x60 cm. 37 providing & fixing aluminum sliding door bolts isi marked anodized (anodic coating not less than grade ac 10 as per is :1868) transparent or dyed to required color or shade with nuts and screws etc. complete: 38 300x16 mm. 39 250x16 mm. 40 providing & fixing aluminum tower bolts isi marked anodized (anodic coating not less than grade ac 10 as per is: 1868) transparent or dyed to requiredcolor or shade with necessary screws etc. complete: 41 300x10 mm 42 250x10 mm 43 200x10 mm 44 150x10 mm 45 100x10 mm 46 providing and fixing isi marked aluminum butt hinges isi marked anodized (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required color or shade with necessary screws etc. complete: 47 125x75x4 mm 48 100x63x4 mm 49 100x63x3.2 mm 50 75x63x3.2 mm 51 providing and fixing ball bearing for rolling shutters. 52 finishing with epoxy paint (two or more coats) at all locations prepared and applied as per manufactures specifications including appropriate priming coat, preparation of surface, etc. complete:on concrete work. 53 chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand).dark shade using ordinary cement. 54 providing and fixing 8 mm. thick gypsum board in false ceiling other places where over in required including supplyall materials, labors, t&p etc. required for proper completion of work. 55 attending to petty maintenance service like plumbing, welding, carpentering, mason with one carpenter plumber or mason and one helper perhour. 56 providing and groutingwith convextra g.p. 2 of standard quality approved byengineer in chargeincluding chipping of rcc and including all labors, t&petc. complete. 57 providing and laying master floor hd of three components epoxy based heavy duty concrete to provide a rough lookingextremely strong beddedscreed motor mixed as prescribed by themanufactures including supply of all material, labors, t&p etc. required for proper completion of work. 58 applying a thick coatof epoxy based two componentproductmaster prime c.n. non solvent resin and hardener by in ratio prescribed by the manufactures after cleaning of surface bychipping, hard wire brushingandwashingfirstwith kerosene oil and than water to make the surface free from oil, grease and any other loose particles etc. and than drying the surface before applying epoxy coat includingsupply of all labour, material and t&p etc. required for proper completion of work. 59 painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete:with residual type petroleum bitumen of grade vg 10 60 providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen 85/25 or 90/15 conforming to is : 702 applied hot @ 1.45 kg per square metre of area for each course, second course of roofing felt type 3 grade i (hessian based self finished bitumen felt) and fourth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimetre per square metre, including preparation of surface but excluding grading complete with : bitumen felt (hessian base) type 3 grade i conforming to is : 1322 61 providing and fixing g.i. chain link fabric fencing of required width in mesh size 25x25 mm made of g.i. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of engineer in charge. 62 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work 63 providing jack hammer with compressor its lead and operator for making hole in slab and breaking r.c.c. and exposing existing reinforcement complete with all t&p labour etc. for proper completion of work as per direction of engineer in charge 64 hiring j.c.b machine with driver/operator, fuel all t&p labour etc. for proper completion of work as per direction of engineer in charge 65 supply & fixing of lever of top portion of aluminium door with required for proper completion of work. 66 providing & fixing rubber linner of approved manufacture in aluminium glazed door and window in power house area including cost of all labour,material and t&p etc. required for proper competion of work. 67 providing & fixing aluminium beading and screw in glazed door & window including cost of all material,labour t&p etc. 68 providing 10 mm thick plaster of paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately) :flat surfaces 69 installation & runningof 1hp /0.5 hp elctric/diesel engine motor pump set with suction of 5 meter depth & delivery pipe up to the distance of 70 meter in near by pit including cost of all hire charges of motor pump set, operator and fuel etc. complete as pr direction of engineer in charge. 70 extra for cutting reinforcement bars manually/ by mechanical means in r.c.c. or r.b. work (payment shall be made on the cross sectional area of r.c.c. or r.b. work) as per direction of engineer in charge. 71 supply of 100 mm long and 15 mm dia. g.i. nozzle includingcutting holes in rcc slab, column and beam including its fixing with cement labor, t&p and material complete (ag. 04/aud/ptpp/2011 12 dt. 27.05.2011) 72 pressure grouting of crakes honey comb. in concrete surface expansion joints as required with cement grout of ratio one part of cement, four parts of water and 3% water proofing cieco no.3 compound (liquids) with the help of grout pump of appropriate pressure excluding cost of filling of g.i. nozzles complete. 73 providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including isi marked m.s. pressed butt hinges bright finished of required size with necessary screws excluding, panelling which will be paid for separately, all complete as per direction of engineer in charge.second class teak wood. (a) 30 mm thick shutters. 74 35 mm thick shutters 75 providing and fixing aluminium round shape handle of outer dia100mm with ss screws etc. complete as per direction of engineerin charge.anodized (ac 15 ) aluminium. 76 installation & running of 5 hp /7.5 hp elctric/diesel engine motor pump set with suction of 5 meter depth & delivery pipe up to the distance of 70 meter in near by pit including cost of all hire charges of motor pump set, operator and fuel etc. complete as pr direction of engineer in charge. 77 providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortarbedding, and joints filled with acid and/or alkali resisting cement as per is : 4457, complete as per the direction of engineer in charge 78 in flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) acid and alkali resistant tile 79 in dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) acid and alkali resistant tile 80 epoxy adhesive 81 coal boulder pitching 22.5 cm thick including cartage of coal boulder from coal handlling area and preparing surface complete. ...

Uttar Pradesh State Construction and Infrastructure Development Corporation Limited - Uttar Pradesh

28942523 construction work of vill. jaurrablock moth jhansi u.p.under scheme pradhan mantri adarsh gram yojana (pmagy) sl. no. item description 1 construciton of c.c. road & one side edging 2 e/w in filling including in ordinary soil , by cartage in embankment to be in 20 cm (8) layers including ramming & dressing the surface to required levels and slopes etc. complete work (253) 3 stone dust filling in foundation including supply of necessary quanity of sand, watering and dressing etc. rate to including cost of material, labour and t&petc. required for poper completion of the work .(all work) 4 concrete with 4 cm .(1.5) gauge approved stone ballast,approved coarse sand and cement in the proportion of 1:4:8 including supply of all materials, labour and t&p etc.required for proper completion of the work.(281) 5 m 150 brick work in 1:4 cement and fine sand of 1.25 f.m. mortar in foundation and plinth including supply of all materials, labours and t&p etc. required for proper completion of the work .(edging)305 6 supply and laying of 125 micron thick approved quality polythen sheet over prepared base. 7 making 10 to 12 mm. thick expansion or contraction joints at interval of 3.00 m each in c.c. road slab by full depth from at header joint and 1/3 depth saw cuts on other joints with cleaning and sealing with asphalt including all labour, t&p etc. as directed by engineer in charge. 8 cement, concrete with 1:2:4 cement, coarse sand and approved 20 mm. gauge granite stone grit including supply of all materials, labour and t&p etc. required for proper completion of work.(pg 39 new) 9 supply and fixing of granit black stone sign board including painting and lettering as directed by engineer in charge.&add for photography etc. 10 construciton ofdrain 0.30x0.30 m in size 11 earth work in foundaion in ordinary soil(lome clay or sand) including lift upto1.50 mandlead upto 30.0 m & inclding flling.watering andramming ofexcavated earth in to the spacebetweenthe building and the sides offoundationtrenches or in tothe plinthandremovelanddisposal of surplasearthas directed by theengineer incharges upto a distance of 30 m (100 fts.)from the foundation trenches.(251) 12 stone dust filling in foundation including supply of necessary quanity of sand, watering and dressing etc. rate to including cost of material, labour and t&petc. required for poper completion of the work .(all work) 13 providing and laying cement andconcrete1:4:8 ( 1 cement: 4 fine sand : 8 graded brick aggreate 40mm nominal size ) including supply ofmaterials.labourand t & p etc. required of proper completionof the work and curing complete , also including castof formwork in foundation & floors.(281) 14 first class brick work in 1: 4 cement & fine sand of 1.25 f m mortar in foundation including supply of all material. labour and t & p etc. (305) 15 20 mm thick plaster with cement morter in proportion of 1:2 cement&fine sand (597) 16 providing and laying cement and concrete flooring 1:2:4 ( 1 cement: 2 corse sand : 4 gradedstone ballast 12.5 mm & below nominal size ) inc luding supply of materials. labour and t&p etc, required of proper completion of the work and curing complete, also including cast of formwork in foundation & floors.(665) 17 supply and installation of led street light 18 supply & fixing of led street light having die cast aluminium body and diffuser with driver set suitable for 75 to 90 watt. confirming up to ip 66 and above protection complete in all respec cat aa (with complete supporting material. make panasonic/anchor, 05 year warranty 19 wire for connection ...

Firozabad Municipal Corporation - Uttar Pradesh

27916285 item rate tender for civil work. 2 earth work in cutting and cartage up to 8 k.m with all complete ( item no. 251+253 ( d ) +253 ( e ) 3 earth work in filling ordinary soil ……… all complete. ( as per analysis ) 4 sand filling in plinth including ………… all complete. ( item no. 255 ) 5 p / l cement concrete in 1:6:12 etc………… all complete. ( dsr pwd si no. 273 ) 6 p / l cement concrete in 1:5:10 etc………… all complete. ( dsr pwd si no. 274 ) 7 p / l cement concrete in 1:2:4 etc………… all complete. ( dsr pwd si no. 4.1 ) 8 p / l cement concrete in 1:1.5:3 etc………… all complete. ( dsr pwd si no. 4.1 ) 9 rcc work p / l in position specified grade of reinforced cemet concrete in 1:2:4 etc……… all complete. ( dsr / pwd si no. 5.1 ) 10 rcc work p / l in position specifled grade of reinforced cement concrete in raft foundation in 1.1.5.3 etc……. all complete. ( dsr / pwd si no. 5.1 ) 11 m 150 class brick work on 1:4 cement and fine sand mortor with all complete. ( dsr si.no. 6.1 ) 12 m 150 class brick work on 1:6 cement and fine sand mortor with all complete. ( dsr si.no. 6.1 ) 13 m 150 class brick work on 1:3 cement and fine sand mortor with all complete. ( dsr si.no. 6.8 ) 14 2 cm thick d.p.c with cement and approved coarse sand 1:2 etc……….. all complete. ( dsr pwd si. no. 360 ) 15 32 mm thick supply and fixing of flush doors etc……… all complete. ( pwd / dsr si no. 470 ) 16 providing & fixing 1.00 mm thick decorative high pressure laminated sheet of plain wood grain in gloss etc……… all complete. ( pwd / dsr si no. 9.127 ) 17 mild steel and iron work of small size etc……… all complete. ( pwd / dsr si no. 502 ) 18 mild steel and iron work of heavy size etc……… all complete. ( pwd / dsr si no. 503 ) 19 mild steel or iron work in plain work etc……… all complete. ( as per analyisis ) 20 providing and fixing stainless steel ( grade 304 ) etc……… all complete. ( pwd / dsr si no. new ) 21 providing and fixing stainless steel ( grade 202 ) etc……… all complete. ( pwd / dsr si no. new ) 22 providing of 1.00 mm thick with zine coating not less then 275 gm / sqm corrugated g.s sheet roofing including vertical. / curved surface fixed with ploymerr coated etc……… all complete. ( pwd / dsr si no. 12.1 ) 23 providing and fixing on wall face unplasticised rigid pvc rain water pipers conforming etc……… all complete. ( pwd / dsr si no. 12.41 ) 24 12 mm thick plastering work on 1:3 cement and course sand mortor with all comoplete. ( pwd dsr si no. 13.9 ) 25 12 mm thick plastering work on 1:4 cement and course sand mortor with all comoplete. ( pwd dsr si no. 13.4 ) 26 12 mm thick plastering work on 1:6 cement and course sand mortor with all comoplete. ( pwd dsr si no. 13.4 ) 27 making grooves 10 to 12 mm wide x 8mm deep in plaster of the wall or in celling vertically or horizontally as required. ( pwd dsr si no. 598 ( 1 ) . 28 repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters etc………… all complete. with cement mortal 1:4 ( 1 cement : 4 fine sand ) ( pwd dsr si no. 14.1 ) 29 cement concrete flooring 1:2:4 ( 40 mm thick floor ) etc ………. all complete. ( pwd dsr si no. 665 ) 30 supply & laying tack coat of bitumin @1 / 4kg per sqm with all complete 31 providing and laying bm 50mm thick compacted with hmp & pavour finisher with all comp. 32 providing and laying sdbc 25mm thick compacted with hmp & pavour finisher with all comp. 33 providing and fixing 18 mm thick granite ( gang saw cut ) , 20 mm thick base cement morrtal 1:4 etc……….. all complete. ( pwd / dsr si no. 11.23 ) 34 providing and laying ceramic glazed floor tiles of size 300x300 mm etc ……… all complete. ( pwd / dsr si no. 11.37 ) 35 providing and laying vitrified tiles in floor with lean concrete of 500x500 sizes ( thickness 10mm ) etc …………. all cmomplete. ( pwd / dsr si no. 11.27a ) 36 providing and fixing 2.2 cm deptth glass strips of 4 mm thick in joints of floor etc……….. all complete. ( pwd / dsr si no. 11.27a ) 37 s / f chequerred precast cement concrete tiles 22 mm thick in footpath 20 mm thick bed of cement mortar 1:4 including preparation of 50 mm thick base with concrete 1:4:8 40 mm b / b complete. ( pwd / dsr si no. 11.2 ) 38 applying priming coat over steel and other metal surface up to 10 cm etc ……. all complete. ( pwd / dsr si no. new 641 ) 39 applying priming coat new wood surface up to 10 cm etc ……. all complete. ( pwd / dsr si no. 19.61 ) 40 painting 1st coat over priming coat on steel and otherr metal surface up to 10 cm etc …………. all complete ( pwd / dsr si no. 19.29 ) 41 painting 1st coat over priming coat on new wood surface up to 10 cm etc …………. all complete ( pwd / dsr si no. 19.29 ) 42 distempering ( first coat ) with oil bound distemeper of approved brand etc …………. all complete ( pwd / dsr si no. 649 ) 43 removing oil paint or varnish from steel and other metal surface of from wood based surface etc …………. all complete ( pwd / dsr si no. 657 ) 44 finishing walls with water proofing cement paint of approved mak such as super snowcem durocem, robiance, guttucem, supercem quality and of required etc …………. all complete ( pwd / dsr si no. 660 ) 45 finishing walls with sandlex matt. coat over a priming coat of water proof cement paint etc …………. all complete ( pwd / dsr si no. new ) 46 well painting ( one coat ) with plastic emulsion pain of approved brand etc ……….. all complete. ( pwd / dsr si no. 18.58 ) 47 finishing walls with putty approved brand and etc ……….. all complete. ( pwd / dsr si no. new ) 48 finishing walls with textured exterior paint approved brand and etc ……….. all complete. ( pwd / dsr si no. new ) 49 dismeantling brick work or stone work in lime or cement etc ……….. all complete. ( pwd si no. 692 ) 50 dismeantling reinforced cement of reinforced brick worrk including stacking etc ……….. all complete. ( pwd si no. 694 ) 51 dismeantling cement concrete or brick or granolithic floors includingg etc ……….. all complete. ( pwd si no. 697 ) 52 dismeantling existing plaster including disposal of refuse as directed etc ……….. all complete. ( pwd si no. 706 ) 53 scrapping old white or colour wash including etc ……….. all complete. ( pwd si no. 708 ) 54 dismentaliing of b.o.e soling / inter locking tiles stacking etc ……….. all complete. ( pwd si no. new ) 55 red sand stone work for wall lining etc. 30 mm thick in 1:3 etc …….. all complet. ( pwd / dsr si no. 7.23 ) 56 construction of granular sub base ( gsb ) etc………. all complee. ( ase per analysis ) 57 consolidation of 45 63 mm and 22.4 53 mm gauge stone ballast 10 cm thick etc………. all complete. ( ase per analysis ) 58 brick soling with straight over burnt brick laid flat and dry brick edging on both side including etc………. all complete. sch pwd no. 762 ( b ) 59 supply and laying of i shaped precast 80 mm ( ordinary grey ) interlocking tiles etc………. all complete. sch pwd no. new 60 supply and laying of i shaped precast 80 mm ( ordinary coloured ) interlocking tiles etc………. all complete. sch pwd no. new 61 supply and laying of i shaped precast 80 mm ( rubber molded ) interlocking tiles etc………. all complete. sch pwd no. new 62 constructing brick masonry manhole etc………… all complete. ninside size 900x800 mm and 500 mm deep including c.i cover frame ( dsr si no. 19.7 ) 63 constructing brick masonry chamber for underground c.i inspection chamber and bends etc………… all complete. ninside dimensions 455x610 mm and 45 cm deep for single pipe : with common burnt clay f.p.s ( non modular ) brick of class designation m 150 ( dsr si no. 19.30 ) 64 material 65 supply of m150 class bricks 66 supply of fine sand . 67 supply of course sand . 68 supply of stone grite 20mm gauge . 69 supply of stone grite 10mm gauge . 70 supply of ordinary portland cement ( j.p, a.c.c, birla, j.k or equivalent ) opc 71 supply of ppc cement ( j.p, a.c.c, birla, j.k or equivalent ) 72 supply of 80 mm thick c.c interlocking tiles ( gray ) with all complete. ( sor no. 8 ) 73 supply of 80 mm thick interlocking tiles ( coloured rubber moulded ) with all complete. ( pwd. 4 ( a ) 74 supply of 100 mm thick interlocking tiles ( grey ) with all complete. ( pwd. 4 ( a ) 75 supply gsb. ( as per anaylisis ) 76 supply of stone dust. 77 head load per chainges ( 30m / cum ) 78 supply of red sand stone 79 supply of r.c.c main hole cover 80 supply of r.c.c main hole ring 81 supply of m.s iron tmt bar 8 mm dia 82 supply of m.s iron tmt bar 10 mm dia 83 supply of m.s iron tmt bar 10 mm dia 84 supply of r.c.c 900x450x100 mm ( pre cast ) 85 supply of r.c.c 1200x450x100 mm ( pre cast ) 86 supply of r.c.c 1500x450x100 mm ( pre cast ) 87 600 dia manhole cover ( pre cast ) 88 labour 89 mistri 90 mason ( for floor & tites work ) 91 painter ( for polishing work ) 92 painter ( for painting work ) 93 mazdoor 94 gardener...

Public Works Department - Uttar Pradesh

27831322 miscellaneous works at different buildings of division 1 dismantling brick work or stone work in lime or cement mortar and including stacking of materials as directed by the engineer in charge within a distance of 60 metres (200 ft.) 2 dismantling reinforced cement concrete or reinforced brick work, including stacking of dismantled materials as directed by the engineer in charge within a dislance of 60 metres(200 ft) n 3 dismantling doors & windows, including chowkhat with hold fast & including stacking of dismantled materials, as directed by the engineer in charge within a distance of 60 m (200 ft.) 4 dismantling existing plaster including disposal of refuse as directed by the engineer in¬charge within a distance of 60 metre (200 ft). 5 scraping old white or colour wash including disposal of refuse as directed by engineer in charge with in a distance of 60 meters (200 feet) si 708 6 earthwork in foundation in mixed soil with moorum / kankar in bundelkhand area including lift upto 1.5m and lead upto 30m and including filling, watering and ramming the excavated earth into the space between the building and sides of foundation trenches or in to the plinth and removal and disposal of surplus earth as desired by the engineer in charge upto a distance of 30m from the foundation trenches (si no. 252) 7 stone dust filling in plinth or foundation including ramming and dressing including s/o all material labour t&p etc complete. 8 plain cement concrete 1:4:8 cement coarse sand 40 mm stone ballast etc. complete. 9 first class brick work in 1:6 cement and fine sand of 1.25 fm mortar in super structure including supply of all material labour and t&p etc complete si no 303+310 10 rcc work with cement approved coarse sand and 2 cm (3/4) gauge approved stone ballast in the proportion of 1:1.5:3 in slab of door and window including sipply of all material, labour t&p etc complete as per required for proper completion of work si no 288(1) 11 mild steel or iron in plain work such as reinforced concrete or reinforced brick work (when not included in an over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of all steel and wastage & overlapping & hooks. 12 12mm thick cement plaster with 1:4 ratio cement and sand mortar with finishing coat neat cement sturry with supply of all material labour t&p. 13 s/f 35 mm sitapur comercial ply wood door shutter as per si no 470/2 14 painting and varnishing three coat including etc complete required for proper completion of the work si no 641+642 15 cement concrete flooring in 1:2:4 cement coarse sand and stone aggregate to size 20 mm laid in one layer finished with flooring coat 665 16 pvc water storage tank syntex or equipment 1000 ltr 17 pvc low level cistern 10 ltr capacity with all internal fitting 18 providing and applying plaster of paris putty of 2 mm thickness over plastered surface of prepare the surface even and smooth complete. dsr 2014 si no 13.26 19 providing and laying of 8 to 10 mm thick vetrified tiles of 600 mm x 600 mm size in flooring or skirting laid wirh 1:3 cement mortar (1 cement : 3 coarse sand) finishing with cement slurry & with pigment grouting & polishing complete i/c supply of all material labour t&p etc required for proper completion of work 20 supply & fixing of fully glaged aluminium window including grill and all fixers including supply of all material labour t&p etc required for proper completion fo work. 21 distemper three coat including etc complete required for proper completion of the work si no 660+661 22 80mm interlocking c.c. block laid in stone dust base & fill joint with 2.36 mm stone dust at joint filled with s/d after leveling & dressing base including supply of all material labour and tools and plants etc. required for proper completion of the work. 23 p/f decorative celling tiles false celling including supply of labour t&p etc. 24 providing and applying fiber reinforced elastomeric liquid waterproofing membrane with resilient acrylic polymers having sun reflectivity index (sri) of 105 on top of concrete roof in three coats. none coat of self priming of elastomeric waterproofing liquid (dilution with water of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness if complete application/system not less than 500 microns). nthe operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, and repairing all the cracks and joints by crack seal pu sealant 25 providing and laying 8 mm thick wooden floor including all fixing, labour, material t&p etc complete. 26 providing & fixing big size gamla with plant including all complete. 27 providing & fixing of superior quality curtains including all complete. 28 random course rubble masonary in 1:4 cement and fine sand mortar in foundation and plinth, including supply of material as order by the engineer in charge, labour, t&p etc, required for proper completion of work si no ni 1 ...

All India Radio - Uttar Pradesh

27566044 repairing of damaged cement concrete flooring for boys and girls dormitory and academic block at jnv bulandshahar...

Public Works Department - Uttar Pradesh

27302878 miscellaneous works at different campus of division . 1 dismantling brick work or stone work in lime or cement mortar and including stacking of materials as directed by the engineer in charge within a distance of 60 metres ( 200 ft. ) 2 dismantling reinforced cement concrete or reinforced brick work, including stacking of dismantled materials as directed by the engineer in charge within a dislance of 60 metres ( 200 ft ) n 3 dismantling doors & windows, including chowkhat with hold fast & including stacking of dismantled materials, as directed by the engineer in charge within a distance of 60 m ( 200 ft. ) 4 dismantling existing plaster including disposal of refuse as directed by the engineer in¬charge within a distance of 60 metre ( 200 ft ) . 5 scraping old white or colour wash including disposal of refuse as directed by engineer in charge with in a distance of 60 meters ( 200 feet ) si 708 6 earthwork in foundation in mixed soil with moorum / kankar in bundelkhand area including lift upto 1.5m and lead upto 30m and including filling, watering and ramming the excavated earth into the space between the building and sides of foundation trenches or in to the plinth and removal and disposal of surplus earth as desired by the engineer in charge upto a distance of 30m from the foundation trenches ( si no. 252 ) 7 stone dust filling in plinth or foundation including ramming and dressing including s / o all material labour t&p etc complete. 8 plain cement concrete 1:4:8 cement coarse sand 40 mm stone ballast etc. complete. 9 first class brick work in 1:6 cement and fine sand of 1.25 fm mortar in super structure including supply of all material labour and t&p etc complete si no 303+310 10 rcc work with cement approved coarse sand and 2 cm ( 3 / 4 ) gauge approved stone ballast in the proportion of 1:1.5:3 in slab of door and window including sipply of all material, labour t&p etc complete as per required for proper completion of work si no 288 ( 1 ) 11 mild steel or iron in plain work such as reinforced concrete or reinforced brick work ( when not included in an over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of all steel and wastage & overlapping & hooks. 12 12mm thick cement plaster with 1:4 ratio cement and sand mortar with finishing coat neat cement sturry with supply of all material labour t&p. 13 s / f 35 mm sitapur comercial ply wood door shutter as per si no 470 / 2 14 painting and varnishing three coat including etc complete required for proper completion of the work si no 641+642 15 cement concrete flooring in 1:2:4 cement coarse sand and stone aggregate to size 20 mm laid in one layer finished with flooring coat 665 16 pvc water storage tank syntex or equipment 1000 ltr 17 pvc low level cistern 10 ltr capacity with all internal fitting 18 providing and applying plaster of paris putty of 2 mm thickness over plastered surface of prepare the surface even and smooth complete. dsr 2014 si no 13.26 19 providing and laying of 8 to 10 mm thick vetrified tiles of 600 mm x 600 mm size in flooring or skirting laid wirh 1:3 cement mortar ( 1 cement : 3 coarse sand ) finishing with cement slurry & with pigment grouting & polishing complete i / c supply of all material labour t&p etc required for proper completion of work 20 supply & fixing of fully glaged aluminium window including grill and all fixers including supply of all material labour t&p etc required for proper completion fo work. 21 distemper three coat including etc complete required for proper completion of the work si no 660+661 22 80mm interlocking c.c. block laid in stone dust base & fill joint with 2.36 mm stone dust at joint filled with s / d after leveling & dressing base including supply of all material labour and tools and plants etc. required for proper completion of the work. 23 p / f decorative celling tiles false celling including supply of labour t&p etc. 24 providing and applying fiber reinforced elastomeric liquid waterproofing membrane with resilient acrylic polymers having sun reflectivity index ( sri ) of 105 on top of concrete roof in three coats. none coat of self priming of elastomeric waterproofing liquid ( dilution with water of 3:1 ) and two coats of undiluted elastomeric waterproofing liquid ( dry film thickness if complete application / system not less than 500 microns ) . nthe operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, and repairing all the cracks and joints by crack seal pu sealant 25 providing and laying 8 mm thick wooden floor including all fixing, labour, material t&p etc complete. 26 providing & fixing big size gamla with plant including all complete. 27 providing & fixing of superior quality curtains including all complete. 28 random course rubble masonary in 1:4 cement and fine sand mortar in foundation and plinth, including supply of material as order by the engineer in charge, labour, t&p etc, required for proper completion of work si no ni 1...

Public Works Department - Uttar Pradesh

27020287 miscellaneous works at different campus of division 1 dismantling brick work or stone work in lime or cement mortar and including stacking of materials as directed by the engineer in charge within a distance of 60 metres (200 ft.) 2 dismantling reinforced cement concrete or reinforced brick work, including stacking of dismantled materials as directed by the engineer in charge within a dislance of 60 metres(200 ft)n 3 dismantling doors & windows, including chowkhat with hold fast & including stacking of dismantled materials, as directed by the engineer in charge within a distance of 60 m (200 ft.) 4 dismantling existing plaster including disposal of refuse as directed by the engineer in¬charge within a distance of 60 metre (200 ft). 5 scraping old white or colour wash including disposal of refuse as directed by engineer in charge with in a distance of 60 meters (200 feet) si 708 6 earthwork in foundation in mixed soil with moorum / kankar in bundelkhand area including lift upto 1.5m and lead upto 30m and including filling, watering and ramming the excavated earth into the space between the building and sides of foundation trenches or in to the plinth and removal and disposal of surplus earth as desired by the engineer in charge upto a distance of 30m from the foundation trenches (si no. 252) 7 stone dust filling in plinth or foundation including ramming and dressing including s/o all material labour t&p etc complete. 8 plain cement concrete 1:4:8 cement coarse sand 40 mm stone ballast etc. complete. 9 first class brick work in 1:6 cement and fine sand of 1.25 fm mortar in super structure including supply of all material labour and t&p etc complete si no 303+310 10 rcc work with cement approved coarse sand and 2 cm (3/4) gauge approved stone ballast in the proportion of 1:1.5:3 in slab of door and window including sipply of all material, labour t&p etc complete as per required for proper completion of work si no 288(1) 11 mild steel or iron in plain work such as reinforced concrete or reinforced brick work (when not included in an over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of all steel and wastage & overlapping & hooks. 12 12mm thick cement plaster with 1:4 ratio cement and sand mortar with finishing coat neat cement sturry with supply of all material labour t&p. 13 s/f 35 mm sitapur comercial ply wood door shutter as per si no 470/2 14 painting and varnishing three coat including etc complete required for proper completion of the work si no 641+642 15 cement concrete flooring in 1:2:4 cement coarse sand and stone aggregate to size 20 mm laid in one layer finished with flooring coat 665 16 pvc water storage tank syntex or equipment 1000 ltr 17 pvc low level cistern 10 ltr capacity with all internal fitting 18 providing and applying plaster of paris putty of 2 mm thickness over plastered surface of prepare the surface even and smooth complete. dsr 2014 si no 13.26 19 providing and laying of 8 to 10 mm thick vetrified tiles of 600 mm x 600 mm size in flooring or skirting laid wirh 1:3 cement mortar (1 cement : 3 coarse sand) finishing with cement slurry & with pigment grouting & polishing complete i/c supply of all material labour t&p etc required for proper completion of work 20 supply & fixing of fully glaged aluminium window including grill and all fixers including supply of all material labour t&p etc required for proper completion fo work. 21 distemper three coat including etc complete required for proper completion of the work si no 660+661 22 80mm interlocking c.c. block laid in stone dust base & fill joint with 2.36 mm stone dust at joint filled with s/d after leveling & dressing base including supply of all material labour and tools and plants etc. required for proper completion of the work. 23 p/f decorative celling tiles false celling including supply of labour t&p etc. 24 providing and applying fiber reinforced elastomeric liquid waterproofing membrane with resilient acrylic polymers having sun reflectivity index (sri) of 105 on top of concrete roof in three coats.none coat of self priming of elastomeric waterproofing liquid (dilution with water of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness if complete application/system not less than 500 microns).nthe operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, and repairing all the cracks and joints by crack seal pu sealant 25 providing and laying 8 mm thick wooden floor including all fixing, labour, material t&p etc complete. 26 providing & fixing big size gamla with plant including all complete. 27 providing & fixing of superior quality curtains including all complete. 28 random course rubble masonary in 1:4 cement and fine sand mortar in foundation and plinth, including supply of material as order by the engineer in charge, labour, t&p etc, required for proper completion of work si no ni 1 ...

Nagar Panchayat - Uttar Pradesh

25632868 construction of proposed slrm (solid & liquid resqurce management) center , excavation in excavation in trenches for foundations and for pipes cables etc . in ordinary soil ) includng lift upto m and dressing of sides and ramming of bottom sand disposal of surplus excavated earth as directed by the engineer i / c with in a lead of 50m , providing and laying in cement concrete 1:4:8 ( 1 cement : 4 corase sand : 8 graded stone aggregate 40 mm nomimal size ) and curing complete including cost of form work in foundatin and floors . , sand fillng in plinth under floors including watering ramming consolidatin and dressing complete including lead upto 1 . 5 m and including cost of sand , providng and injecting chemical emulsion for precounstructionan antitermite tretment and creating a chemical barrier under and alround the coloumn p;its wall trenches basement ecavation top surface if plinth filling jnction of wall and floor , along the the external perimeter of biding expansion joints , surrpmeter of binding expansion joints , surrounding of pipes and conduits etc , complete ( plinth are of the building at ground floor only shall be measured as per i . s . ( 4 ) treatment junction of wall and the floor 7 . 5 liters / sqm ( 5 ) treatment of soil along external perimeter of building 7 . 5 liter / sqm ( 6 ) treatment of soil under apron along external perimeter 5 liter / . sqm ( as per manufacturere standare dilution ) , rcc work with cement approved coarse sand and 20 mm guage approved stone grit in the proportion of 1:1 . 5:3 in lintels of doors and window excluding supply of reinforcement and its fixing and binding the same with 24 bwg bidning wire and including ncessary centering and shuttering etc . and also including supply of all material labour and tools and plants etc . requried for proper completion of the work . same as aboe but for the lighter beam i . e . haivng spans upto 6 m ( using 1:1 . 5:3 mix conmcrete ) , same as aboe but for slab i . e . haivng spans upto 6 m ( using 1:1 . 5:3 mix conmcrete ) , as in item 6 above but in r . c . c . raft foundation and footign with approved stone ballast ( using 1:1 . 5:3 mix concrete ) , as in item 6 above but in coloumn with approved stone ballast ( using 1:1 . 5:3 mix concrete ) , class m 150 brick work in 1:6 cement coarse sand ( of 2 . 25 finess modulus ) mortar in foundation & plinth including supply of all material , labour toos and plants etc . required for proper completion of the work . , class m 150 brick work in 1:6 cement coarse sand in super structure mortar including supply of all materials , labour toos and plants etc . required for proper completion of the work . , class m 150 half / brick work in 1:4 cement coarse sand in super structure mortar including supply of all materials , labour toos and plants etc . required for proper completion of the work . , mild steel or iron in plain work such as reinforced concrete or reinforcement brick work ( when not included in an over all rates ) wrought to required shape as necessary including benefit for proper completion fo the work and including supply of all steel and wastage and over lappign and hooks . and authorised over lappign shall be measured upto floor two leve . , 12 mm cement plaster in single coat on rough side of single or half brick wall for interior plastgering up to floor two level including internal rounded angles not excededing 80 mm in girth and finished even and smooth ( 1 ) cement : 6 fine sand , 15 mm cement plaster in single coat of rough side of single of hlf brick wall for extgerior plastering upto floor two level including internal rounded angles chamfers , and / or rounded angles not eexcedding 80 mm in girth and finished even and smooth no extra for mixing any additive 1 cement : 6 fine sand , cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand :4 graded stone aggregatge 12 20 mm nominal size laid in one layer neat cement ( 40 mm thick floor ) , steel work in buil u tubular ( round , square or rectangular hollow tubes , etc . ) trusses etc . including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer including welding and bolted with special shaped washers etc . complete flectric restance of induction bult weled tubes . , proving corrugated g . s . sheet roofing including vertical / curved surface fixed with polymer coated j or l hooks , bolts and nuts 8 mm diameter with bitumen and g . i . limpet washers or with g . i . limpet washers filled with white lead , including a coat of aproved steel primer and two coats of approved paint on overlapping or sheets complete ( up to any ) pitch in hozizontal / ; vertical rafters and trusses and including cutting to size and shape wherever required 0 . 63 mm thick with zine coating not less than 275 gm / sqm , providing ridges or hips of width 60 cm overall width plain g . s . sheet fixed with polymer coated j or l hooks bolts and nuts 8 mm dia g . i . limpet and bitumen washers completed 0 . 63 mm thick with zinc coating not less than 275 gm / sqm , providing and fixing 15 cm wide , 45 cm overall semi curcular plain g . s . sheet gitter with iron brackets 40x3 mm size , bolts , nuts and washers etc . includng making necessary connection with rain water pipes complete . 0 . 63 mm thick with zine coating not less than 275 gm / sqm , painting two coat over priming coat ( but includng cost of priming coat ) on steel and other metal surfaces upto 10 cm widt or girth or small articles not exceeding 0 . 10 sqm n are white superior synthetic enamel such as luxol3hi gloss apeolite superlac , dulux specified brushing to give an even shade and includng cleaning the surface of all dirt , dust and other foreigtn matter sand papering and stoping including cost of all materitals , labour t&p etc . requirred for proper completion of the owrk for steel surface . , painting two coat over priming coat ( but includng cost of priming coat ) on steel and other metal surfaces upto 10 cm widt or girth or small articles not exceeding 0 . 10 sqm n are white superior synthetic enamel such as luxol3hi gloss apeolite superlac , dulux specified brushing to give an even shade and includng cleaning the surface of all dirt , dust and other foreigtn matter sand papering and stoping including cost of all materitals , labour t&p etc . requirred for proper completion of the owrk for wooden surface , p . f . mild stel or iron in plain work such as reinforced concrete or reinforced brick work ( when not included in over all rrates ) wrought to required shape as ncessary including bending for proper completion of the work and includng supply of steel its wastage bend hooks and authorised over tapping shall be measureed upto floor two leve . , providng and fixing g . i . chain link faore fencing of required width in mesh size 50x50 mm includng strengthening with 2 mm dia wire or nuts bolts and washers as required complete as per the direction of engineer in charge made of g i . wire of dia 4 mm , m . s . iron work of small sized and sections such as holding down bolts , hold fast tie rods grating etc . wrought to required from includng supply of steel bolts , nuts wastage etc . and fiving required for proper completion of the work . ( a ) angle iron door chaukhats 40x40x5 , z section with m . s . grill , fixing of door , window / ventilator chaukhats in position ( a ) door...

Public Works Department - Uttar Pradesh

25616872 replacement of aluminium partition, drain slab, windows, almirah, painting of residential building, boundary wall, wooden flooring, cement concrete flooring work, water proofing work, renewal and repair of kitchen, toilet, bathroom, roof, replacement of frame of windows, aluminium door sheet....

Uttar Pradesh State Construction and Infrastructure Development Corporation Limited - Uttar Pradesh

25023697 rest work of beautification at lehra devi farenda distt . maharajganj . , dharamshala , excavation of foundation in ordinary soil ( loam clay or sand ) including lift upto excavation of foundation in ordinary soil ( loam clay or sand ) including lift upto 1 . 50 meter and lead upto 30 meter and including filling , watering and ramming of excavated earth into the trenches or into the space between the building and sides of foundation trenches or into the plinth and removal and disposal of sur plus earth as directed by the engineer incharge up to a distance of 30 meters from the foundation trenches . , filling of carted earth . , providing and laying in cement concrete 1:4:8 ( 1 cement:4 coarse sand :8 graded stone aggregate 40 mm nominal size ) and curing complete , including cost of form work , in foundation and floors . , sand filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8 kms . from the site of work and including watering , dressing etc rate to include cost of all materials labour t & p etc required for proper completion of work . , providing and injecting chemical emulsion for pre constructional antitermite treatment and creating a chemical barrier under and alround the column pits walltrenches basement excavation top surface if plinth filling junction of wall and floor , along the the external perimeter of binding expansion joints , surrounding of pipes and conduits etc , complete ( plinth area of the building at ground floor only shall be measured as per i . s . 6313 ( partll 1981 ) alderineemulsifiable concentrate or any other approved material such as heptrachlor or chlordane wil be used . the rate of application of chemical emulsion shall be as follows: ( 1 ) treatment for masonary& foundation 5 liters per sqm . ( 2 ) back fill in immediate contact with foundation 7 . 5 liters/sqm ( 3 ) treatment of top surface of plinthfilling 5 liters/sqm ( 4 ) treatment junction of wall and the floor 7 . 5 liters/sqm ( 5 treatment of soil along external perimeter of building 5 liters/sqm , r . c . c . work with cement approved coarse sand and 20 mm . jguage approved stone grit im the proportion of 1 : 1 . 5 3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 bwg binding wire and including necessary centering and shuttering etc . and also including supply of all materials , labour and tools and plants etc , required for proper completion of the works . strength of the concrete shall not beless than m 20 , as in item no . 6 above but for slabs ( using 1:1 . 5:3 mix ( concrete ) strength of the concrete shall not beless than m 20 , as in item 6 but for the lighter beamsi . e . having spans upto 16 m . ( using 1:1 . 5:3 mix concrete ) strength of the concrete shall not beless than m 20 . , as in item 6 abave but in r . c . c . raft foundation and footing with approved stone ballast . ( using 1:1 . 5:3 mix ( concrete ) strength of the concrete shall not beless than m 20 , as in item 6 above but in r . c . c . columns in 1:1 . 5:3 having strength not less than m 20 . , m 150 brick work in 1: 6 cement and coarse sand of 2 . 25 fineness modulus mortar in fqundation and plinth lincluding supply of all materials , labour and tools and plants etc . required for proper completion of the work . , m 150 brick work in 1 6 cement and coarse sand of 2 . 25 fineness modulus mortar in super structure above plinth level up to floor two level ( up to two storeys ) including necessary cutting and moulding of brick work as required and lalso including honeycombed brick work in thickness of wall more than 12cms . , same as in item no . 13 but in 1: 4cement and coarse sand mortar in superstructure for wall thickness 12 cms& below brick work . , p/f tmt fe 500 or iron in plain work such as reinforced concrete or reinforced . brick work ( when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level . , 12 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth . 1 cement : 6 course sand , 12mm cement plaster in single coat on fair side of single or i half brick wall for exterior plastering up to floor two level lincluding internal rounded angles chamfers , and / or rounded jangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive . 1 cement: 4course sand , making grooves 10 to 12 mm wide x 8mm deep in plaster the jallor in ceiling vertically of horizontally as required , providing and fixing 18 mm thick gang saw cut , mirror polished , premoulded and prepolished , machine cut for kitchen platforms , vanity counters , window sills , facias and similar locations of required size , approved shade , colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement:4 coarse sand ) , joints treated with white cement , mixed with matching pigment , epoxy touch ups including rubbing , curing , moulding and polishing to edges to give high lgloss finish etc . complete at all levels granite of any colour and shade area of slab over 0 . 50 sqm , providing and fixing 18 mm thick gang saw cut . mirror polished , premoulded and prepolished , machine cut for kitchen platforms , vanity counters , window sills , faciasandli similar locations of required size , approved shade , colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement: 4 coarse sand ) , joints treated with white cement , mixed with matching pigment , epoxy touch ups , including rubbing , curing , moulding and polishing to edges to give high gloss finish etc . complete at all levels granite of any colour and shade area of slabover 0 . 50 sqm . , supply and fixing of kota stone in flooring 20mm thick and joint filled with 1:2 cement and coarse sand with approved colouring materials to be given an even shade with 12 mm base coat ( bedding ) of 1:2 cement & coarse sand morter and polished by hand or machine and finally finished with french manson polish or other approved polish including supply of all materials , labour , tools & plants etc required for proper completion of the work . 25 mm thick , cement concrete flooring 1 2 :4 ( 1 cement 2coarse sand 4 jgraded stone aggregate 12 20mm nominal size laid in one layer neat cement ( 40mm thick floor ) , providing and fixing isi marked flush door shutters conforming to is:2202 ( part 1 ) decorative type , core of block board construction with frame of 1st clas hard wood and well matched teak 3ply veneering with vertical grains or cross bands and face veneers on both faces of shutters , 35mm thick including isi marked stainless steel butt hinges with necessary screws . , mild steel or iron in plain work such as reinforced concrete or reinforced , brick work ( when not included in over all rates ) wrought to required shape as necessary including bending for iproper completion of the work and including supply of all steel land wastage & over lapping & hooks . using m . 5 . angles 40x40x6mm for diagonal braces . , distempering with oil bound washable distermper of approved jbrand and and manufacture to give an even shade : new work ( two or more coats ) over and including water tinnable priming coat with cement primer ( for internal wall & ceiling ) , providing stainless steel sliding bolts 16 mm dia with nuts land 250mm long , ( a ) 250mmx10mm , ( b ) 200mmx10mm , providing stainless steel door...