Public Works Department - Uttar Pradesh

39662484 tender for repair work of fire fighting equipment installed in the district court jaunpur premises. 1 sitc of smoke detector as per fire specification including making connection with wire system 2 sitc of manual call point break glass type housed in m.s. sheet including make connection 3 sitc of electronic lmt hooterhoused in m.ssuitable forwall mounting / ceiling , including connection 4 supply and wiring ofsub main with 2 no. 1.5 mm2 pvc insulation 1100 volt grade single core copper conductor cable in 20mm dia heavy risid steel conduit on surface. 5 sitc of single headed s.s hydrant valve comprising of 80mm dia flanged bend 63 mm dia s.s oblique pattern landing valve complete with blank cap etc. 6 sitc of rrl hose 63mm dia 15 mtr long complete with s.s couplingconfirming to is 636 7 repairingofhosebox m.ssheetwithglassfronteddoorincluding locking arrangementtoaccommodate2nos.rrlhose&1nos.ssbranchpipewithnozzel. 8 repairingof fire alarm local control panel for above complete 9 repairingof fire alarm main panel for above complete in all respect. 10 first aid hose reel pipe 30 meter long rubber pipe shut of nozzle, 20mm dia gate valve complete 11 repairing of electrical operated main fire pump consisting of1. horizontaltype, multistage, centrifugal, splitcasingpumpofcastironbody&bronze impeller with stainless steel shaft, mechanical seal conforming to is 1520 for 2280 lpm at 70 mtr head.2. suitablehptefctypesquirrelcageinductionmotorof minimum60hp.suitablefor operationon415volts, 3phase50hz, acsupplywithip55protectionforenclosure, horizontal foot mounted type with class f insulation, conforming to is 325.3. completeinstallationwithconcretefoundation ( alledgesshouldbeprotectedwith 50mmx50mmx5mm angle iron ) , common bed plate of iron channel, coupling , coupling guard, vibration pads etc. complete work as per requirement. 12 repairing of diesel engine driven pump consisting of1. horizontaltype, multistage, centrifugal, splitcasingpumpofcastironbody&bronze impeller with stainless steel shaft, mechanical seal conforming to is 1520 for 2280 lpm at 70 mtr head.2.suitable hp, 1500rpm, minimum 60 hp, water cooled, auto start mechanism diesel engine with flexible coupling, exhaust pipe insulatedwith 50 mm glass wool with 1.0 mm thick aluminium sheet cladding, with silencer etc.confirming pollution norms.3. completeinstallationwithconcretefoundation ( alledgesshouldbeprotectedwith 50mmx50mmx5mmangle iron ) and commonbed plate of ironchannel etc. for mounting the diesel engine and pump. complete in all respects. 13 repairing of electrical driven jockey pumpconsisting of1. horizontaltype, multistage, centrifugal, splitcasingpumpofcastironbody&bronze impeller with stainless steel shaft, mechanical seal conforming to is 1520 for 180 lpm at 70 mtr head.2. suitablehptefctypesquirrelcageinductionmotorofminimum10hp.suitablefor operationon415volts, 3phase50hz, acsupplywithip55protectionforenclosure, horizontal foot mounted type with class f insulation, conforming to is 325.3. completeinstallationwithconcretefoundation ( alledgesshouldbeprotectedwith 50mmx50mmx5mm angle iron ) , common bed plate of iron channel, coupling , coupling guard, vibration pads etc. complete work as per requirement. 14 repairing of factory fabricated wired metalclad dust & vermin proof floor mounting main electric control panel for main electrical fire pump, diesel engine pump 1no. jockey pump with starter switch volt meter amp. meter & battery charger with battery. hrc type 315 amp. / 415 volt. main switch engine control relay 75hp star delta starter with timer, single phase protector led indicator lamn etc 15 gst extra @18%...

North Central Railway - Uttar Pradesh

39468238 auction sale of scrap ms items consisting of angle, plate, round bar, bed plate and nut bolt etc. total quantity= 17.475 mt approx. delivery on actual weight basis. delivery will be given on as is where is basis.cutting allowed for easy loading. lot is approachable by pakka road. bidders are required to visit the lot site for being aware about the site condition / location and satisfy themselves before participating in the e auction. ds 8 note no. 098780 date 01.06.2023...

Military Engineer Services - Uttar Pradesh

39456776 tender for special repair of road inside csd depot under ge west at lucknow; 1 excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation etc. or for manholes, cesspits, shafts etc. not exc. 10 sqm on plan and getting out in hard / dense soil complete all as specified and directed. 2 excavation in trenches not exc. 1.50 m wide and exc. 1.50 m but not exc. 3.0 m in depth for foundation etc. or for manholes, cesspits, shafts etc. not exc. 10 sqm on plan and getting out in hard / dense soil complete all as specified and directed. 3 m & l for providing plain cement concrete, type c 2, 1:3:6 ( using 40 mm graded stone aggregate ) as in sub base of floors including finishing surface even and rough to receive the topping layer complete all as specified and directed. 4 m & l for brick work with old size fly ash bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:4 complete all as specified and directed. 5 m & l for providing plain cementconcrete type b 1, 1:2:4, ( using 20 mm graded stone aggregate ) , as in copings, bed block for embedding hold fasts, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed. 6 s & f of300mm bore reinforced concrete pipe class np 3 laid, jointed with collars in neat cement slurry complete all as specified and directed. 7 m & l for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and fair complete all as specified and directed. 8 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed. 9 removing surplus excavated material to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed. 10 scarifying or picking exc 50 mm and n exc 100 mm deep gravelled, macadamor bituminous macadam surfaces in area exc 400 sqm complete all as specified and directed. ( without down portion area ) 11 excavation over areas not exceeding 1.5 m deep and getting out in hard / dense soil complete all as specified and directed. 12 m & l for rolling and consolidation formation surface in cutting to requrired gradient and camber including filling in depression and hollow watering leavlling etc complete using power roller excedding 8 tonne and not exceeding 12 tone capacity complete all as specified and as directed. note: rolling and consolidating formation surface in cutting to the required gradient and camber under optimum moisture conditions to achieve at lest 98% of maximum dry density determined using modified proctor density determination method as per relevant is code. 13 m & l for soling ( or sub base ) 150mm thick ( spread thickness ) or querried stones, granite trap or basalt interistices filled, surface formed and rolled and consolidated to required gradient and camber complete all as specified and as directed. 14 m & l forwbm 7.5 cm thick ( compacted thickness ) with coarse aggregate of granite, trap or basaltof grading 2 ( 63 to 40 mm size ) for first layer & grading 3 ( 50 to 20mm size ) for second layer, spread, rolled & consolidated to gradient and camber as required complete all as specified and as directed. 15 m&l for 75mm thick dry lean concrete ( dlc ) design mix ( m 15 ) in single layer with 7 days compressive strength as 10 n / sqmm with minimun cement ( opc ) content 250kg / cum of concrete with necessary joints as per morth specification all as per irc:sp 49 1998 including form work if required and rolling complete to achieve desired and strength complete all as per irc:sp 49 1998 and rolling complete to achieve desired density and strength complete all as specified and directed. note: in the event of increase in cement content as per design mix formula, nothing extra shall be admissible and quoted rates are deemend to include for the same and minus price adjustment shall be carried out in case of consumption of cement it less than above said quantity. 16 m&l for 10mm thick layer of sand including watering and rolling over dbm and dlc etc complete all as specified and directed. 17 m&l for 400 micron transparent high density polyethlene ( hdpe ) film sheet grade i conforming to is 10889 laid over sand layer complete all as specified and directed. note: ( i ) side lap of 150 mm and end lap of 300 mm shall be provide wherver required. the rate quoted shall be deemed included for the laps. ( ii ) clear area only shall be considered for payment purpose and nothing extra shall be allowed for laps. 18 m&l for 150mm thick pavement quality concrete ( pqc ) as per design mix using crushed stone aggregate having minimum field flexural strength of 45 kg / sq cm with non cirullar / tirangular synthetic fibre as per manufactures instructions @0.25% by weitht of cement ( min cement content shall be 400 kg / cum using opc ) laid to level gradient and camber spread paved compacted & finished using mechianical ( mechinical fixed form paver ) including necessary form work complete all as specified and directed. note: ( a ) in the event of increase in cement as per design mix formula, nothing extra shall be admissible and quoted rates are deemed to include for the sameand minus price adjustment shall be carried out in case of consumption of cement it less than above said quantity. ( b ) non circular synthetic fibers shall be measured and paid separately as supply only under respective item. ( c ) design mix to be prepared after incorporating fibre. 19 supply only non circular synthetic fibers of length 12mm specific gravity 1.31 to 1.41 uv stable and alkali resistant ( as per astm c 1116 02 and icao ac 32 ) to be used upto 0.25% by weight of cement complete all as manufacturs specification and as specified and directed. 20 m&l for forming 25 mm wide expansion joints to full depth of pavement concrete salb as per shape and section show on drawing and primed and filled with and including compressible closed cell permoulded high perfomance joint filler board and provision of closed cell polyethylene back up road 30 mm dia, and top 15 mm primed and sealed with and using polyurethance based sealling compound ( polyethylene joint sealant complying with b55212 & bs 4254 and en 141875 2003 ( for hydrolysis water resistance test ) with suitable primer as per manufacutrers recommendation complete all as shown on drawing and specified and as directed with minimum maf_+ 30 % complete all as manufacturs specification and as specified and directed. 21 m & l for forming construction joint 28mm deep and 10mm wide ( using diamomd cutter ) , primed and providing a 12 mm dia polystyrene back up rod / debonding strip and top 15mm primed and sealed using polyurethane based sealing compound complying with bs5212 & bs 4254 and en141875 2003 ( for hydrilysis / resistance test ) and promer of specified make as per manufracturs recommendation complete with bullnosing of edges of front of joint n exc 5mm wide all as specified and directed. 22 m & l for forming dummy joint 8 mm wide and 26 mm deep, 02 coats of priming and providing a backup rod of 10 mm dia with debonding tape & top 15 mm primed and sealed with and using polyurethane based sealing compound ( polyurethane joint sealant complying with bs5212 n bs4254 and en 141875 2003 ( for hydrolysis / water resistance test ) including intial 3 mm wide saw cut upto 97 mm depth with suitable prime as per manufactures recommendations including minimum maf 30% ( with ten yerars performances guarantee ) and applying masking tape after sealant sealant is applied complete all as specified and diercted. 23 m&l for pcc 1:3:6 type c 2 using 20 mm graded stone aggregate as in concrete bed to drain pipe including packing under, and hunching against the sides of pipes after they are laid and tested reinforced concrete pipe class np3 300 mm dia pipe and jointed complete with collars all as specified and directed....

Kisan Sahkari Chini Mills Limited - Uttar Pradesh

39250597 supply of mechanical circulator for 60 ton pan with planetary gear motor for season 2023 24 , tender for the supply of mechanical circulator 60 ton pan with erection & commissioning and trail & testing as per specification mentioned below for season 2023 24 , supply scope technical specification of mechanical circulator for capacity 60 ton vaccum pan of b massecuite 01 no., bearing with planatory general motor, vfd pannel & cable etc. mechanical circulator to suit for60tonscapacity , vacuum pan ( top mounted ) having a shaft machine from 150 mm dia en 8 in three piece couple through a set of fixed ms coupling with gunmetal bush . the lower shaft shall of ms drum duly machined fitted with necessary ss vanes thickness 16 mm& a guide bearing at other end & supported with center down take of pan calandria . the upper shaft shall be supported with cast steel housing fitted with thrust roller spherical roller bearing & gun metal bush with complete sealed & leak proof with mechanical seal fitted with flexible coupling for both output & input shaft complete with suitable vertical planetary gear box & suitable motor, 1440 rpm vertical flange mounted motor. the final rpm of mechanical circulator will be 48 . the middle shaft will be supported with pan bodyand bottom shaft will be supported with downtakeof pan . motor required – for60ton pan – 60 hp , 1440 rpm vertical flange mounted motor planetary gearbox make – kavastu / top gear motor make – abb / crompton / siemens variable frequency device & control panel make – compton / siemens / abb supporting staging the supporting staging & structure provided from pan floor & the bed plate &cast steel housing with spherical roller bearingwill be fitted with supporting structure & also platform & railing will be provided by party. `...

Kisan Sahkari Chini Mills Limited - Uttar Pradesh

38976332 supply of mechanical circulator for 60 ton pan with planetary gear motor for season 2023 24 , tender for the supply of mechanical circulator 60 ton pan with erection & commissioning and trail & testing as per specification mentioned below for season 2023 24 , supply scope technical specification of mechanical circulator for capacity 60 ton vaccum pan of b massecuite 01 no., bearing with planatory general motor, vfd pannel & cable etc. mechanical circulator to suit for60tonscapacity , vacuum pan (top mounted ) having a shaft machine from 150 mm dia en 8 in three piece couple through a set of fixed ms coupling with gunmetal bush . the lower shaft shall of ms drum duly machined fitted with necessary ss vanes thickness 16 mm& a guide bearing at other end & supported with center down take of pan calandria . the upper shaft shall be supported with cast steel housing fitted with thrust roller spherical roller bearing & gun metal bush with complete sealed & leak proof with mechanical seal fitted with flexible coupling for both output & input shaft complete with suitable vertical planetary gear box & suitable motor, 1440 rpm vertical flange mounted motor. the final rpm of mechanical circulator will be 48 . the middle shaft will be supported with pan bodyand bottom shaft will be supported with downtakeof pan . motor required – for60ton pan – 60 hp , 1440 rpm vertical flange mounted motor planetary gearbox make – kavastu/ top gear motor make – abb / crompton / siemens variable frequency device & control panel make – compton / siemens / abb supporting staging the supporting staging & structure provided from pan floor & the bed plate &cast steel housing with spherical roller bearingwill be fitted with supporting structure & also platform & railing will be provided by party. `...

Public Works Department - Uttar Pradesh

38917448 tender for new construction of rudrapur gauribazar mukhya road to gram sabha lohar tola to yadav tola link road. 1 earth work in cutting or embankment in ordinary soil loam, clay or sand in excavation to be in the form of regular pits not exceeding 0.5 m in depth and earthwork in embankment to be 20 cm layers including ramming and dressing the surface to the required labvels and slopes and also including 1.5 m lift and 30 m lead. the earth from cutting to be used in making embankment or to be deposited as spoil banks within 30 m distance as directed by e / i.as per s.i. no. 253 ( excluding gst ) 2 construction of granular sub base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per clause 401. ( excluding gst ) 3 providing, laying, wbm grade 2 with 45 63mm size stone ballast, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled smooth roller 8 10 tonnes in stages to proper grade and camber, applying and brooming, stonescreening / binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per clause 405.2 ( including all taxes required & i / chire charges of road roller ) ( excluding gst ) 4 providing, laying, wbm grade 3 with 22.4 53mm size stone ballast, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled static roller 8 10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening / binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density. grading 3 as per clause 405.3 ( including all taxes required & i / chire charges of road roller ) ( excluding gst ) 5 providing and applying primer coat with bitumen emulsion on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.75 kg / sqm using mechanical means. as per techinical specfication clause 502 ( including all taxes required but including cost of bitumen emulsion ) ( excluding gst ) 6 providing and applying tack coat with bitumen ( vg 10 ) using pressure distributor at the rate of 0.30 kg per sqm on the prepared bituminous / granular surfacetreated with primer & cleaned with hydraulic broom as per technical specification clause 503 ( including all taxes required but excluding cost of bitumen vg 10 ) ( excluding gst ) 7 providing, laying and rolling of open graded premix surfacing of 20 mm thickness composed of 13.2mm, 11.2 mmaggregates in proportion of 2:1 usingvg 10 bitumen@ 1.46 kg per sqm to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled roller 80 100 kn static rollar capacity, finished to required level and grades to be fallowed by seal coat as per technical specification clause 508, excluding cost of bitumen grade vg 10 ( excluding gst ) 8 providing and laying seal coat by manual means with vg 10 grade bitumen sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using type c as per technical specification clause 510 ( including all taxes required and hire charges of road roller but excluding cost of bitumen ) ( excluding gst ) 9 earth work in cutting or embankment in ordinary soil loam, clay or sand in patries onboth side of road including ramming dressing required to proper completion of work including all labour t&p etc all complete. as per s.i. no. 253 ( excluding gst ) 10 brick edging 8 cm wide on both sides of the road by m 150 bricks complete as perpwd detailed specification no 20.15 ( excluding gst ) 11 hume pipe culvert 350mm dia 2 no , 600mm dia 1 noexcavation of foundation in ordinary soil including lift upto 1.50m and lead up to 30m and including filling watering and ramming of excavation earth into trenches or into the plinth and removal and disposal of surplus earth as direction byi / e up to a distance of 30m from the foundation trench as per s.i no 250 ( excluding g.st ) 12 concrete with 4 cms gauge brick ballast fine sand of 1.25 fineness modules and cement in the ratio 8:4:1 in foundation and under floors including supply of all materials, labour, t&p etc required for proper completion of the work as per si no 275 13 p.p.cwork with cement approved coarse sand 20 cm guage approved stone ballast in the propostion of 1:2:4 in lintel of doors and windows etc and bed plates excluding the supply of reinforcement and its bending and including providing and fixing necessary centering and suttering and removal after completion of the work &supply of all other material labours and t&p ( etc required for the proper completion of the work s.ino 284 ( excluding cost of g.s t ) 14 supply of 600 mm dia np 3 hume pipes 15 laying of600 mm dia np 3 hume pipes 16 supply of 350 mm dia np 3 hume pipes 17 laying of 350 mm dia np 3 hume pipes...

Kisan Sahkari Chini Mills Limited - Uttar Pradesh

38707956 supply of mechanical circulator for 60 ton pan with planetary gear motor for season 2023 24 , tender for the supply of mechanical circulator 60 ton pan with erection & commissioning and trail & testing as per specification mentioned below for season 2023 24 , supply scope technical specification of mechanical circulator for capacity 60 ton vaccum pan of b massecuite 01 no., bearing with planatory general motor, vfd pannel & cable etc. mechanical circulator to suit for60tonscapacity , vacuum pan ( top mounted ) having a shaft machine from 150 mm dia en 8 in three piece couple through a set of fixed ms coupling with gunmetal bush . the lower shaft shall of ms drum duly machined fitted with necessary ss vanes thickness 16 mm& a guide bearing at other end & supported with center down take of pan calandria . the upper shaft shall be supported with cast steel housing fitted with thrust roller spherical roller bearing & gun metal bush with complete sealed & leak proof with mechanical seal fitted with flexible coupling for both output & input shaft complete with suitable vertical planetary gear box & suitable motor, 1440 rpm vertical flange mounted motor. the final rpm of mechanical circulator will be 48 . the middle shaft will be supported with pan bodyand bottom shaft will be supported with downtakeof pan . motor required – for60ton pan – 60 hp , 1440 rpm vertical flange mounted motor planetary gearbox make – kavastu / top gear motor make – abb / crompton / siemens variable frequency device & control panel make – compton / siemens / abb supporting staging the supporting staging & structure provided from pan floor & the bed plate &cast steel housing with spherical roller bearingwill be fitted with supporting structure & also platform & railing will be provided by party. `...

Kisan Sahkari Chini Mills Limited - Uttar Pradesh

38537036 supply of mechanical circulator for 60 ton pan with planetary gear motor for season 2023 24 , tender for the supply of mechanical circulator 60 ton pan with erection & commissioning and trail & testing as per specification mentioned below for season 2023 24 , supply scope technical specification of mechanical circulator for capacity 60 ton vaccum pan of b massecuite 01 no., bearing with planatory general motor, vfd pannel & cable etc. mechanical circulator to suit for60tonscapacity , vacuum pan (top mounted ) having a shaft machine from 150 mm dia en 8 in three piece couple through a set of fixed ms coupling with gunmetal bush . the lower shaft shall of ms drum duly machined fitted with necessary ss vanes thickness 16 mm& a guide bearing at other end & supported with center down take of pan calandria . the upper shaft shall be supported with cast steel housing fitted with thrust roller spherical roller bearing & gun metal bush with complete sealed & leak proof with mechanical seal fitted with flexible coupling for both output & input shaft complete with suitable vertical planetary gear box & suitable motor, 1440 rpm vertical flange mounted motor. the final rpm of mechanical circulator will be 48 . the middle shaft will be supported with pan bodyand bottom shaft will be supported with downtakeof pan . motor required – for60ton pan – 60 hp , 1440 rpm vertical flange mounted motor planetary gearbox make – kavastu/ top gear motor make – abb / crompton / siemens variable frequency device & control panel make – compton / siemens / abb supporting staging the supporting staging & structure provided from pan floor & the bed plate &cast steel housing with spherical roller bearingwill be fitted with supporting structure & also platform & railing will be provided by party. `...

Northern Railway - Uttar Pradesh

38449170 auction sale of scrap of w.i. steel span girder with 4 bed plates ( size 620 x 720 x 50.00 mm ) in each girder of bridge no. 1133 & 1135. total 10 girders. each length is 13.4 meter. total 134 meter. total approximate weight 114.20 mt....

Kisan Sahkari Chini Mills Limited - Uttar Pradesh

38346213 supply of mechanical circulator for 60 ton pan with planetary gear motor for season 2023 24 , tender for the supply of mechanical circulator 60 ton pan with erection & commissioning and trail & testing as per specification mentioned below for season 2023 24 , supply scope technical specification of mechanical circulator for capacity 60 ton vaccum pan of b massecuite 01 no., bearing with planatory general motor, vfd pannel & cable etc. mechanical circulator to suit for60tonscapacity , vacuum pan ( top mounted ) having a shaft machine from 150 mm dia en 8 in three piece couple through a set of fixed ms coupling with gunmetal bush . the lower shaft shall of ms drum duly machined fitted with necessary ss vanes thickness 16 mm& a guide bearing at other end & supported with center down take of pan calandria . the upper shaft shall be supported with cast steel housing fitted with thrust roller spherical roller bearing & gun metal bush with complete sealed & leak proof with mechanical seal fitted with flexible coupling for both output & input shaft complete with suitable vertical planetary gear box & suitable motor, 1440 rpm vertical flange mounted motor. the final rpm of mechanical circulator will be 48 . the middle shaft will be supported with pan bodyand bottom shaft will be supported with downtakeof pan . motor required – for60ton pan – 60 hp , 1440 rpm vertical flange mounted motor planetary gearbox make – kavastu / top gear motor make – abb / crompton / siemens variable frequency device & control panel make – compton / siemens / abb supporting staging the supporting staging & structure provided from pan floor & the bed plate &cast steel housing with spherical roller bearingwill be fitted with supporting structure & also platform & railing will be provided by party. `...

Uttar Pradesh Jal Nigam - Uttar Pradesh

38046654 supply of rate for civil, electrical, sanitoryand other materials at asra yojana auraiya as per nit and tender document , earth work in excavation in trenches for foundation pipes, cable etc in ordinary sol ( loam clay or sand ) inlcuding lift upto 1.5 mt. lead upto 30mt. and dressing of sides and rammings of bottom and disposal of surplus excavated earth as directed by the engineer. , upto 1.50 m to 3.00 m deep , upto 3.00 m to 4.50 m deep , upto 4.50 m to 6.00 m deep , filling of carted earth , laying in position cement concrete of specifiedgrade including the cost of centring and shuttering all work upto plinth level. , in cement concrete 1:4:8 ( 1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size ) , in cement concrete 1:2:4 ( 1 cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size ) , providing and injecting chemical emulsion for pre constructional antitermite treatment and creating a chemical barrier under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete. ( plinth area of the building at ground floor only shall be measured as per i.s.6313 ( partii 1981 ) alderine emulsifiable concentrate or any other approved material such as heptrachlor or chlordane will be used. the rate of application of chemical emulsion shall be as follows : ( 1 ) treatment for masonary & foundation 5 liters per sqm. ( 2 ) back fill in immediate contact with foundation 7.5 liters / sqm ( 3 ) treatment of top surface of plinth filling 5 liters / sqm ( 4 ) treatment junction of wall and the floor 7.5 liters / sqm ( 5 ) treatment of soil along external perimeter of building 7.5 liters / sqm ( 6 ) treatment of soil under apron along external perimter 5 liters / sqm. ( as per manufacturers standard dilution ) , r.c.c. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 bwg binding wire and including necessary centering and shuttering etc.and also excluding supply of all materials, and including labour and tools and plants etc, required for proper completion of the works. , ground floor , first floor , second floor , as in item no. 6 above but for slabs ( using 1:1.5:3 mix concrete ) . , ground floor , first floor , second floor , as in item 6 but for thelighterbeams i.e. having spans upto 6 m. ( using 1:1.5:3 mix concrete ) , ground floor , first floor , second floor , as in item 6 abovebut inr.c.c.raft foundation and footingwithapproved stone ballast. ( using1:1.5:3mix concrete ) , as in item 6 above but in r.c.c. columns in 1:1.5:3 having strength not less than m 20. , ground floor , first floor , second floor , m 150 brick work in 1:6 ( one cement and six coarse sand sand of 2.25 fineness modulus ) mortar infoundation & plinth includinglabour and t & p etc & excluding supply of all materials, required for proper completion of the work. , m 150 brick work in 1:4 ( one cement and six coarse sand sand of 2.25 fineness modulus ) mortar infoundation & plinth includinglabour and t & p etc & excluding supply of all materials, required for proper completion of the work. , laying damp proof course 40mm thick with cement concrete 1:2:4 ( 1 cement : 2 coarse sand ( zone iii ) : 4 graded stone aggregate 12.5mm nominal size ) , applying a coat of residual petroleum bitumen of grade of vg 10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. , same as in item no. 11 abovebutin super structure above plinth level up to floor two level ( up to two storeys ) includingnecessarycutting and moulding of brick work asrequiredand also including honeycombed brick work in thickness of wall more than 12cms. ( 1:6 cement : coarse sand ) , ground floor , first floor , second floor , same as in item no. 14 but in1:4 cement and coarse sand mortar in superstructure for wall thickness 12 cms & below brick work. , ground floor , first floor , second floor , mild steel or iron in plain work such as reinforced concrete or reinforced, brick work ( when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and excluding supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. , ground floor , first floor , second floor , 15 mm cement plaster on rough side of single or half brick wall of mix : 1:3 ( 1 cement: 3 coarse sand ) , 15 mm cement plaster in single coat on rough side of single or halfbrick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. ( 1 ) 1 cement : 6 fine sand . , ground floor , first floor , second floor , 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and / or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. ( 1 ) 1 cement : 6 finesand. , ground floor , first floor , second floor , engraving lines in the plaster of outer face well vertically & horizontally to display the surface as stone facing as directed by the engineer in charge including labpur, & t & p etc. required for proper completion of the work. , ground floor , first floor , second floor , add for plaster drip course / groove in plastered surface or moulding to r.c.c. projections. , laying 8 to 10 mm thick ivory or light shade vitrified tiles of 600 x 600 mm size with all colours and shades, laid on 20mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) finishing with cement slurry & with pigment grouting & polishing complete including supply of all labour, t & p etc. excluding the cost of materials required for proper completion the work. , ground floor , first floor , second floor , laying 8 to 10 mm thick ivory or light shade vitrified tiles of 600 x 600 mm size with all colours and shades, laid on 20mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) finishing with cement slurry & with pigment grouting & polishing complete including supply of all labour, t & p etc. excluding the cost of materials required for proper completion the work. , ground floor , first floor , second floor , kota stone slab flooring over 20 mm ( average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand ) : 25 mm thick , ground floor , first floor , second floor , kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm ( average ) thick cement mortar 1:3 ( 1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. , ground floor , first floor , second floor , fixing of 6 mm thick approved china white / coloured glazed tiles in flooring or dado laid with 1:3 cement and approved coarse sand mortar finished and jointed with white cement slurry and pigment and polishing complete includinglabour and tool sand plants & excluding supply of all materials, etc. required for proper completion of the work. , ground floor , first floor , second floor , 25 mm thick cement concrete flooring 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 12.5mm nominal size and below ) by laid over base concrete finished with floating coat of neat cement ( base concrete to be paid separately ) including fixing of glass strips. ( excluding cost of glass strips ) , supply of flush doors commercial qualityconforming to i.s.2202 part i ( 1983 ) including fixing of wooden cleats and stoppers , 35 mm thick , ( a ) single leaf , ( b ) double leaf , 32 mm thick , ( a ) single leaf , extra for providing and fixing flush doors with decorative veneering instead of non decorative isi marked flush door shutters conforming to is: 2202 ( part i ) , fixing of flush / pvc doors including fixing of wooden / pvc cleats and stoppers and includingfixing and adjustment of hinges, bolts, locks, handle, springs. fittings to be supplied departmentally. , supply of factory made panel pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. m.s. frame shall have a coat of steel primers of approved make and manufacture. m.s. frame covered with 5 mm thick heat moulded pvc ‘c’ channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide pvc sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide pvc sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. top, bottom and lock rails shall be provided both side of the panel. 10 mm ( 5 mm x 2 ) thick, 20 mm wide cross pvc sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side pvc sheet to be fitted in the m.s. frame welded / sealed to the styles & rails with 7 mm ( 5 mm+2 mm ) thick x 15 mm wide pvc sheet beading on inner side, and joined together with solvent cement adhesive. an additional 5 mm thick pvc strip of 20 mm width is to be stuck on the interior side of the ‘c’ channel using pvc solvent adhesive etc. complete as per direction of engineer in charge, manufacturer’s specification & drawing. 30 mm thick plain pvc door shutters , mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods, gratings etc. ( when not included in an over all rates ) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. , m.s. hold fast for doors and windows , m.s. grill , z section winodws ( openable ) , m.s. angle door chaukhat 40*40*5 , fixing of door, windows / ventilators chaukhats in position. , ( a ) door chaukhats , ( b ) window chaukhats , ( c ) ventilator chaukhats , distempering ( two coat ) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as berger, j&n, shalimar, asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. ( inside walls ) , ground floor , first floor , second floor , finishing walls with two coat of acrylic smooth exterior paint of best quality including supply of all materials labour and tool sand plants etc. required for proper completion of the work. , ground floor , first floor , second floor , finishing wall with water proof cement paint of approved make and quality on new wood with two coat to give an even shade including supply of all materials, labour, tools and plant etc. required for proper completion of the work. ( two coat ) , wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : two or more coats on new work supply of all materials, labour, tools and plant etc. required for proper completion of the work. ( two coat ) , distempering ( two coat ) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as berger, j&n, shalimar, asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth excludingcost of all materials. ( ceiling ) , providing & applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. , supply of 150 mm bright finished floor stainless steel door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete. , supply of stainless steel sliding door bolts isi marked anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade with nuts and screws etc complete. ( a ) 250mm x 16mm . , supply of stainless steel towerbolts ( barrel type ) with necessary screws etc. complete , ( a ) 300mm x 10mm , ( b ) 250 mm x 10mm , supply of bright / matt finished stainless steel handles of approved quality & make with necessary screws etc all complete. ( a ) 125 mm , providing and laying cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a ) applying a slurry coat of neat cement using 2.75 kg / sqm of cement admixed with water proofing compound conforming to is. 2645 and approved by engineer in charge over the rcc slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b ) laying brick bats with mortar using broken bricks / brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 ( 1 cement : 5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge over 20 mm thick layer of cement mortar of mix 1:5 ( 1 cement :5 coarse sand ) admixed with water proofing compound conforming tois : 2645 and approved by engineer in charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c ) after two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge. d ) finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 ( 1 cement :4 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e ) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. all above operations to be done in order and as directed and specified by the engineer in charge : with average thickness of 120 mm and minimum thickness at khurra as 65 mm. , painting or vanishing two coat on iron work in small areas or new wood work with one coat of ready mixed priming paint and one coat of approved superior ready mixed paint of clear synthetic varnish including supply of all materials, labour, t & p etc. required for proper completion the work. paint to be used should confirm to the i.s.i. no. 103 1950. , same as item above but on new wood surface. , fixing panes of glass with equal or equivalent i.s.i. marked quality putty, brads and springs including supply of all materials, labour etc. complete. 3.80 to 4.70 mm thick , chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing & excluding supply of all materials complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement :4 coarse sand ) : light shade pigment using white cement. , filling of light cinder filling under floor of toilets & other sunken roofs. , labour charges for wiring points for light with 1.5 sqmm.frlsh pvc insulated single core copper condutor cable in pvc conduit pipe partly concealed in wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sqmm.frlsh pvc insulated multistrand copper conductor cable as earth continuity wire and piano type switch etc. complete in all respects. , same as item no. ( 1 ) but for two way light points. , same as item no. ( 1 ) but for fanandlight duty exhaust fan. , same as item no. ( 1 ) but for5amp plug point with piano type switch and socket etc. , addition when modular type switches etc are used in place of piono type switches etc. in various wiring points. , addition for light / fan points with modular type switchin place of piono type switch. , addition for plugpointswith modular type switchin place of piono type switch. , addition for exhaust fanpointswith modular type switchin place of piono type switch. , wiring of submains with 2 nos. 2.5 sq.mm & with 1 no. earth wire of 1.5 sq.mm fr pvc insulated 1100 v grade single core multistrand copper conductor cable in 20 mm dia heavy duty ( 2mm thick ) pvc conduit complete, including supply of all material, labourand t&p etc. required for proper completion of the work as directed by engineer i / c. , wiring of submain 2 number 4 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 20mm dia pvc conduit partly concealed in wall and partly laid in slab along with one number 2.5 sqmm frlsh pvc insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects. , wiring of submain 2 number 6 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 20mm dia pvc conduit partly concealed in wall and partly laid in slab along with one number 4 sqmm frlsh pvc insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects. , wiring of submain 4 number 10 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 32mm dia pvc conduitalong with two numbers 6 sqmm frlsh pvc insulated multistranded copper conductorcable as earth contunity wire etc. complete in all respects. , wiring of submain 4 number 16 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 40mm dia pvc conduitalong with two numbers 10 sqmm frlsh pvc insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects. , wiring of submain 4 number 25 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 50mm dia pvc conduitalong with two numbers 16 sqmm frlsh pvc insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects. , fixing and concealing of20mm dia.2mm thick pvc conduit pipe with isi mark embossed and with pvc acessories confirming to is no. 3419 for drawing wires duly sealed at joints with original resin / adhesive to make the complete piping rigid, plastering with cement sand mortar finished to level with matching colour including cost of material labour and t & p etc required for proper completion of work ( fortelephone ) , erection and testing of ceiling fan and regulator for room height upto 3.5mts. including supply of 3mm thick g.i. pipe 19mm dia duly painted, complete in all respects. , erection and testing exhaust fan on the exhisting hole with suitable size of rag bolts nuts and washers etc. complete in all respects. , fixing of hexagonal / round g.p. fan box of approved make made up of 1.0mm thick isi marked g.p. sheet spot weeldeed four to eight holes of 25.4 mm for pipe entry of the box. holes should be semi shuttered type with 0.5mm g.p. sheet made upper & lower cover duly screewed fitted with 300mm round zink coted m.s bar x 12mm & brand name should be embossed.fixing with wiring conduit laid in the r.c.c roof before concreting alongwith supply of all material, labour, t&p etc. required for proper completion of the work. , supply of ceiling fan with fan motor of a.c permanent insulation, capacitor rating conforming bee 5 star rating and is:374 / 79 and also comply with is: 1709 / 1984 with latest amendment. the rated voltage 220 / 240 volts, 50hz, 1 ph ac the fan assemble should consists of down road blades, shackle canopies etc and with double ball bearing system. bee 5 star rated 1200mm sweep , fixingofelectronic fan regulator ( modular ) 120 280 v. isimarked, on the existing switch board including making connetion, required material, labour t / p etc for proper completion of work to the satisfaction of engineer in charge of work. , fixing of led tube light with metal heavy dutybox type batten light fitting 2 x 22 watt suitable for up to 2 x 22 watt led polycarbonate tube light complete including tube etc suitable for both surface & surface complete in all respects. ( cat: aaa ) , fixing of led tube light with metal heavy dutybox type batten light fitting 1 x 22 watt suitable for up to 1 x 22 watt led polycarbonate tube light complete including tube etc suitable for both surface & surface complete in all respects. ( cat: aaa ) , fixing of recess / surface mounting round 10 to 15 watt, cut out min 125mm, height min 40mm, led down lighter having powder coated die cast aluminium housing with heat sink, diffuser / reflector and driver set, suitable for 24hr continuous operation, complete in all respect. ( cat: aaa ) , fixing of single led light wall bracket on matching m.d.f.e.g board base etc. complete in all respect. ( cat: aaa ) , fixing of water tight oblong 10 watt led bulhead luminaire with driverr set confirming to ip 65 and above protection complete in all respect. ( cat: aaa ) , fixing of surface / flush mounting distribution boards with additional metal door withot mcb complete in all respects. ( cat a ) , 4 way tpn , 6 way tpn , 8 way tpn , fixing of 6amp to 32 amp ( 10 ka ) sp mcb in existing mcb, db complete with connections as required. ( cat: a ) , fixing and making connection of following mcbs complete in all respects as per direction and satisfaction of engineer in charge. ( cat: a ) , 40 amp. fp mcb ( cat: a ) , 63 amp. fp mcb ( cat: a ) , fixing of surface / flush mounting v tpn distribution boards with additional metal door withot mcb complete in all respects. ( cat a ) 4 way v tpn , fixing and making connection of following mccbs complete in all respects as per direction and satisfaction of engineer in charge. ( cat: a ) , 100 amp. fp mccb ( cat: a ) , 125 amp. fp mccb ( cat: a ) , 160 amp. fp mccb ( cat: a ) , fixing and making connection of following mcbs complete in all respects as per direction and satisfaction of engineer in charge. ( cat: a ) , 40 amp. tp mcb ( cat: a ) , 63 amp. tp mcb ( cat: a ) , fixing of power plug with 15a / 250 v flush type switch and 5 pin 15 a / 250v flush type universal socket in suitable m.s. box of 175mmx100x50mm size with phenolic laminated bakellite sheet cover 3mm thick fixed with brass machine screws and cup washer. , fixing of power plug with 20a / 250 v flush type switch and 5 pin 20 a / 250v flush type universal socket in suitable m.s. box including supply of all material, labor t&p etc. required for proper completion of work. , fixing of single pole mcbs blanking plate complete in all respects. ( cat: a ) , fixing and making connection of following mccbs complete in all respects as per direction and satisfaction of engineer in charge. 63 amp. fp mccb , supply and burying of 600mm x 600 mmx6mm g.i. plate, vertically for earthing with its top atleast 3 mts. below ground level complete with 20mm g.i.pipe and funnel for watering and two earthing leads of no.8to10swg g.i.wire in 15mm dia g.i. pipe upto switch board ( from apron to switch board the cost of g.i. pipe and g.i. wire will be extra ) 30cm. square c.i. frame with hinged cover, masonary housing, alternate layers / of charcoal / coke and salt at least 150mm thick alround etc. complete in , laying of 25mmx3mm g.i. strip for earthing purpose as required complete in all respects. , fixing of two number 8 swg g.i. wire in 15mm dia gi pipe for earthing purpose as required complete in all respects. , laying of aluminium conducter, pvc insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the , 95 sqmm3.5 core , 70 sqmm3.5 core , 50 sqmm3.5 core , 35 sqmm3.5 core , 25 sqmm3.5 core , 10 sqmm4 core , fixing of brass nickle plated compression gland for pvc insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respects. the armouring of the cable shall be properly connected with the earth as per dire , 95 sqmm3.5 core , 70 sqmm3.5 core , 50 sqmm3.5 core , 35 sqmm3.5 core , 25 sqmm3.5 core , 10 sqmm4 core , fixing of palm / pin type copper tin plated cables sockets ( lugs ) to the cable leads, insuslating with tape and making of connections etc. complete in all respects as per direction of engineer incharge. , 95 sqmm , 70 sqmm , 50 sqmm , 35 sqmm , 25 sqmm , 16 sqmm , 10 sqmm , 6 sqmm , fixing ofmodular boxes, base & cover plate , fixing of following size / modules, gi box along with modular base& cover plate for modular switches in recess etc as required. 1 or 2 module ( 75mm x 75 mm ) , fixing ofmodular type switch / socket : , fixing of following modular switch / socket on theexisting modular plate & switch box including connections but excluding modular plate etc as required. , telephone socket outlet , tv antenna socket outlet , bell push , fixing of call bell / buzzer suitable single phase, 230 v etc as required. , laying oftelephone wire following pair 0.5 sqmm fr pvc insulated annealed copper conductor, unarmoured telephone cable in the existing surface / recessed steel / pvc conduit as required. 2 pair , drawing of co axial tv cable rg 6 grade, 0.7 mm solid copper conductor pe insulated, shielded with fine tinned copper braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required. , drawing telephone wire following pair 0.5 sqmm fr pvc insulated annealed copper conductor, unarmoured telephone cable in the existing surface / recessed steel / pvc conduit as required. , 20 pair , 10 pair , fixing of 10 pair junction boxes for floors and building with krone connectors , with connection and punching of same , fixing of 20 pair junction boxes for floors and building with krone connectors , with connection and punching of same , fixing of 50 pair junction boxes for floors and building with krone connectors , with connection and punching of same , laying unplastisized rigid pvc pipe conforming to is:13592 type a including jointing , cuttingand making good the walls & floors as per requirement. 150mm , supply of ac 230 / 250 volts, 50 hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required 300mm sweep. , fixing of energy meter and other accessories including connections etc. complete as required 3 phase meter , erection of ac 230 / 250 volts, 50 hz wall fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required450mm sweep. , supply of ac 230 / 250 volts, 50 hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required450mm sweep. ( at labs ) , fixing of wired decorative mirror light on suiatable for 9 watt led with lamp complete in all respect. , fixing of factory wired integral led flood light luminaires with die cast aluminium housing built with driver set suitable for 40 to 50 watt conforming to ip 65 / 66 protection complete in all respect. ( cat aaa ) , providing and laying water proofing treatment in sunken portion of wcs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a ) first layer of slurry of cement @ 0.488 kg / sqm mixed with water proofing cement compound @ 0.253 kg / sqm. this layer will be allowed to air cure for 4 hours. b ) second layer of slurry of cement@ 0.242 kg / sqm mixed with water proofing cement compound @ 0.126 kg / sqm.this layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. the rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. , fixing of stainless steel ( grade 304 ) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, i / c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, excluding the cost of materials on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer in charge. , providing and fixing of expansion joint system related with floor location as per drawings and direction of engineer in charge. the joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per astm b221 02. the system shall be such that it provides floor to floor / floor to wall expansion control system for various vertical localtion in load application areas thatccommodates multi directional seismic movement without stress to its components. system shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. the cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre engineered self centering arrangement that freely rotates / moves in all directions.the self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. provision of moisture barrier membrane in the joint system to have watertight joint is mandatory requirement all as per the manufactures design and as approved by engineer in charge. ( material shall confirm to astm 6063 ) floor joint of 100 mm gap , providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of engineer in charge. the joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper astm b221 02. the system shall be such that it provides watertight roof to roof / roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. system shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. the cover plate shall be designed of width and thickness required to satisfy movement , and loading requirements and secured to base members by utilizing manufacturer’s pre engineered self centering arrangement that freely rotates / moves in all directions. the self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including verticalisplacement. the joint system shall resists damage or deterioration from the impact of falling ice, exposure to uv, airborne contaminants and occasional foot traffic from maintenance personnel. provision of moisture barrier membrane in the joint system to have water tight joint is mandatory requirement. ( material shall confirm to astm 6063. ) roof joint of 100 mm gap , providing and fixing of expansion joint systemelated with wall joint ( internal / external ) location as per drawings and direction of engineer in charge. the joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per astm b221 02. the material shall be such that it provides an expansion joints system suitable for vertical wall to wall / wall to corner application, both new and existing construction in office buildings & complexes with no slipping down tendency amongst the components of the joint system. the joint system shall utilize light weight aluminum profiles exhibiting minimalexposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. ( material shall confirm to astm 6063 ) .wall joint of 100 mm gap , fixing in position stainless steel grade 304 plate 1.0 mm thick as per design for expansion joints. 200 mm wide. , granite stone slab 18 mm thick mirror polished quarter rounded with anti skid lines in treads of staircase full length flooring over 20 mm ( average ) thick base laid over and jointed with cement slurry mixed with pigment to match the shade of including rubbing & polishing complete with base of cement mottar 1:4 ( 1 cement : 4 coarse snad ) etc. complete excluding the cost of materials. , ground floor , first floor , second floor , fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of t iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, ocking arrangement, stoppers, handles, including applying a priming coat of approved steel primer & excluding the cost of materials. , fixing rolling shutters of approved make of 80 × 125 mm ( 3 × 18 gauge ) cold rolled ml lath inter lockedthrough their eintire length and joined together at the end by locks and mountedon specially designed pipe shaft with brackets and wall bearing & excluding the cost of materials. , 40mm thick cement concrete flooring 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size and below ) by laid over base concrete finished with floating coat of neat cement ( base concrete to be paid separately ) including fixing of glass strips. ( excluding cost of glass strips ) , fixing glass strips in joints of floors and skirting or dado add the item of laying floors flush with floor level including supply of all materials, labour, t & p etc. required for proper completion the work. ( a ) 37 mm wide and 3.15 mm thick , 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) and top layer 12 mm thick cement hardener consisting of mix 1:2 ( 1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size ) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturers specifications.but excluding the cost of materials etc. complete. , supply of 80mm thick rubber moulded cement concrete interlocking pavers block. the compressive strength of concrete pavers blocks shall not be less than 30mpa & 4.5kg / no. , providing and laying of 80mm thick rubber moulded cement concrete interlocking pavers block. the compressive strength of concrete pavers blocks shall not be less than 30mpa & 4.5kg / no. , fixing of angle iron frame 40x40x6 mm in position. , fencing with r.c.c. post placed at required distance, embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side only, provided with horizontal lines and two diagonals of barbed wire weighing 9.38 kg per 100 metres ( minimum ) , between the two posts fitted and fixed with g.i. staples on wooden plugs or g.i. binding wire tied to 6 mm bar nibs fixed while casting the post ( cost of r.c.c. posts, struts, g.i. barbed wire, earth work and concrete to be paid for separately ) , mild steel or iron work in heavy sizes such as trusses built up gates, door frames, record racks, roof work gates etc. wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. , providing and fixing fly proof galvanized m.s. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. with 2nd class teak wood beading 62x19 mm. , providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 35 mm thick shutters with isi marked m.s. pressed butt hinges bright finished of required size , providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. extra for providing and fixing flush doors with decorative veneering instead of non decorative isi marked flush door shutters conforming to is: 2202 ( part i ) on one side only , p / f curtain rods of 1.25mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with c.p. brass screws and wooden plugs etc. wherever necessary complete ( a ) 25 mm dia. , fixing of g.i. pipe ( 80 mm dia ) as per design & drawing as per drection of eic , fabrication of angle iron door chaukhat of 40*40*6 mm , supply of concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m ) , having 50 nos rounds per 6 metrelength, upto 3 m height of wall with existing angle iron ‘y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal r.b.t. reinforced barbed wire, stud tied with g.i. staples and g.i. clips to retain horizontal, including necessary bolts or g.i. barbed wire tied to angle iron, all complete as per direction of engineer in charge, with reinforced barbed tape ( r.b.t. ) / spring core ( 2.5mm thick ) wire of high tensile strength of 165 kg / sq.mm with tape ( 0.52 mm thick ) and weight 43.478 gm / metre. , fixing of concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m ) , having 50 nos rounds per 6 metrelength, upto 3 m height of wall with existing angle iron ‘y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal r.b.t. reinforced barbed wire, stud tied with g.i. staples and g.i. clips to retain horizontal, including necessary bolts or g.i. barbed wire tied to angle iron, all complete as per direction of engineer in charge, with reinforced barbed tape ( r.b.t. ) / spring core ( 2.5mm thick ) wire of high tensile strength of 165 kg / sq.mm with tape ( 0.52 mm thick ) and weight 43.478 gm / metre ( cost of materialsshall be paid separately ) , supply of m.s. foot rest as per standard design with 20x20mm sq bars. , fixing of m.s. foot rest including fixing with 20x20x10 cm. cement concrete block 1:3:6 ( 1 cement : 3 coarse sand : 6 gradded aggregate of nominal size 20mm ) as per standard design with 20x20mm sq bars. , supply ofc.i. tee at the inlet and outlet of septic tank. , fixing c.i. tee at the inlet and outlet of septic tank. , supply of 75mm dia vent pipes. , fixing of 75mm dia vent pipes. , supply of 75mm dia cast iron terminal guard. , fixing of 75mm dia cast iron terminal guard. , supply ofprecast rcc manhole cover and frame of required shape and approved quality. , m.d. 10 circular shape 500mm internal diameter , m.d. 2.5 circular shape 450mm internal diameter , fixing in position precast rcc manhole cover and frame of required shape and approved quality. , m.d. 10 circular shape 500mm internal diameter , m.d. 2.5 circular shape 450mm internal diameter , excavating trenches in all kinds ofsoil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. , up to 1.50 m depth , pipes 80 mm to 300 mmdiameter , 1.50 m to 3.00 m depth , pipes 80 mm to 300 mmdiameter , opentimbering in trenches including shuttering and shoring complete. ( measurement to be taken of the face area timbered ) , depth not exceeding 1.5 meter , depth 1.5 to3.00meter , supply of non pressurenp 2 class ( light duty ) rcc pipe with collars etc. complete. , 150 mm.dia. rccpipes , 250 mm.dia. rccpipes , 100 mm dia rcc pipes , laying of nonpressurenp 2 class ( light duty ) rcc pipe with collars jointed withstiffmixtureofcement mortar in the proportion of 1:2 ( 1cement : 2 finesand ) includingtestingof joints etc. complete. , 150 mm.dia. rccpipes , 250 mm.dia. rccpipes , 100 mm dia rcc pipes , laying cement concrete 1:5:10 ( 1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size ) upto the haunches of pipes including bed concrete as per standard design , 150 mm.dia. rccpipes , 250 mm.dia. rccpipes , 100 mm dia rcc pipes , constructing brick masonry manhole in cement mortar 1:4 ( 1 cement :4 coarse sand ) rcc top slab with 1:2:4 mix ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size ) , foundation concrete 1:4:8 mix ( 1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size ) inside plastering 12mm thick with cement mortar 1:3 ( 1 cement :3 coarse sand ) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size ) finished with a floating coat of neat cement complete as per standard design. , inside size 90x80cms and 45cms deep including ci cover with frame ( light duty ) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg ( weight of cover 23 kg and weight of frame 15kg ) . , extra for depth for manholes: , inside size 90x120cms and 90cms deep including ci cover with frame ( medium duty ) 455x610mm internal diamensions total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58kg ) . , extra for depth for manholes: , supply of orange colour safety footrests of minimum 6 mm thick plastic encapsulated as per is:10910 on 12 mm dia steel bar conforming to is:1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm thread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing. , fixing of orange colour safety footrests of minimum 6 mm thick plastic encapsulated as per is:10910 on 12 mm dia steel bar conforming to is:1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm thread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size ) complete as per design. , supply of double flanged ( screwed / welded ) centrifugally ( spun ) ductile iron pipes of class k 9 conforming to is 8329 100mm dia ductile iron double flanged , fixing & laying double flanged ( screwed / welded ) centrifugally ( spun ) ductile iron pipes of class k 9 conforming to is 8329 100mm dia ductile iron double flanged , supply of ci specials such as bends, reducers, collars etc. including cartage, loading, unloading, taxes, excise etc. complete. , fixing of ci specials such as bends, reducers, collars etc. including cartage, loading, unloading, taxes, excise etc. complete. , supply of push on joints to centrifugally ( spun ) cast iron pipes or ductile iron pipes including testing of joints and including the cost of rubber gasket : 100mm dia pipes , fixing of push on joints to centrifugally ( spun ) cast iron pipes or ductile iron pipes including testing of joints and including the cost of rubber gasket : 100mm dia pipes , supply ofc.i. sluice valves ( with cap ) complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) : 100mm diameter , fixing of c.i. sluice valves ( with cap ) complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) : 100mm diameter , supply of c.i. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete ( the tail pieces, tapers etc. if required will be paid separately. a ) 50mm dia , fixing of c.i. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete ( the tail pieces, tapers etc. if required will be paidsaperately 50mm dia , supply of g.i. pipes ( medium ) complete with g.i. fittings , 80mm nominal bore. , 65mm nominal bore. , 50mm nominal bore. , 40mm nominal bore. , 32mm nominal bore. , 25mm nominal bore. , 20mm nominal bore. , 15mm nominal bore. , laying, jointing, testing & commisioning ofg.i. pipes complete with g.i. fittings includingtenching and refilling etc. ( external work ) , 80mm nominal bore. , 65mm nominal bore. , 50mm nominal bore. , 40mm nominal bore. , 32mm nominal bore. , 25mm nominal bore. , 20mm nominal bore. , 15mm nominal bore. , supplying of specials for pressure pipe. , fixing of specials for pressure pipe. , supply ofgate valve ( with cap complete with bolts, nuts, rubber insertion etc. , 80mm nominal bore. , 65mm nominal bore. , 50mm nominal bore. , 40mm nominal bore. , 32mm nominal bore. , 25mm nominal bore. , fixing of gate valve ( with cap complete with bolts, nuts, rubber insertion etc. , 80mm nominal bore. , 65mm nominal bore. , 50mm nominal bore. , 40mm nominal bore. , 32mm nominal bore. , 25mm nominal bore. , constructing masonry chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 ( 1 cement : 4 coarse sand ) for sluice valve, with c.i. surface box 100mm, top diameter, 160 mm bottom diameter and 180mm deep ( inside ) with chained lid and rcc top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i / c necessary excavation, foundation concrete 1:5:10 ( 1 cement :5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design : with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , constructing brick masonry chamber 600 x 600x750mm insidewithf.p.s. brickwork in cement mortar 1:4 ( 1 cement : 4 coarse sand ) for sluice valve / air valve, with c. i. surface box 100 mmtop diameter, 160 mm bottom diameter and 180mm deep ( inside ) with chained lid and rcc top slabwith 1 : 2 : 4 mix ( 1 cement : 2 coarsesand : 4 gradestone aggregate 20 mm nominal size ) ; necessary excavation, foundationconcrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size ) and inside plasteringwithcement mortar 1 : 3 ( 1 cement : 3 coarsesand ) 12mmthick finished with a floatingcoatofneat cementcomplete as per standarddesign , supply offire brigade inlet with 63 mm dia instantaneous inlet complete with all necessary fittings and ms enclosure with glass door made of 18 / 16 swg sheet. 4 way , fixing, installation, testing & commissioning offire brigade inlet with 63 mm dia instantaneous inlet complete with all necessary fittings and ms enclosure with glass door made of 18 / 16 swg sheet. 4 way , supply of sluice valve complete with flanges, gasket, nut bolts 150 mm , fixing, installation, testing & commissioning of sluice valve complete with flanges, gasket, nut bolts 150 mm , supply of nrv complete with flanges, gasket and nut bolts. 150 mm , fixing, installation, testing & commissioning of nrv complete with flanges, gasket and nut bolts. 150 mm , supply of ms pipes conforming to is:1239 ( medium b class ) including all fittings like anchor fasteners, brick masonry supports, couplings, bends, elbows, tees and flanges etc. welded or screwed joints as required ( for riser ) , 150 mm dia , 100mm dia , fixing of ms pipes conforming to is:1239 ( medium b class ) including all fittings like anchor fasteners, brick masonry supports, couplings, bends, elbows, tees and flanges etc. welded or screwed joints as required, cutting holes and chases in brick or rcc walls and making good complete. ( for riser ) , 150 mm dia , 100mm dia , supply of manual swing type first aid fire hose reel conforming to is: 444 complete with all other necessary fixing accessories. , fixing, installation, testing and commissioning of manual swing type first aid fire hose reel conforming to is: 444 complete with all other necessary fixing accessories. , supply of fire man axe. , fixing of fire man axe. , supply of singal headed hydrant landing valve comprising of 80 mm dia flanged bend 63 mm dia, with cap and chain conforming to is:5290 ( make : newage / minimax / safex / firex ) , fixing, installation, testing & commissioning of singal headed hydrant landing valve comprising of 80 mm dia flanged bend 63 mm dia, with cap and chain conforming to is:5290 ( make : newage / minimax / safex / firex ) , supply of rrl hose pipe 63 mm dia × 15 mtr. long with gm coupling conforming to is : 636 ( make newage / jayshree / crc ) , fixing, installation, testing & commissioning of rrl hose pipe 63 mm dia × 15 mtr. long with gm coupling conforming to is : 636 ( make newage / jayshree / crc ) , supply of short branch pipe as per is:903 ( make : newage / safex / firex ) , fixing, installation, testing & commissioning of short branch pipe as per is:903 ( make : newage / safex / firex ) , supply of butterfly valve complete with flanges, gasket, nut bolts 100 mm , fixing, installation, testing & commissioning of butterfly valve complete with flanges, gasket, nut bolts 100 mm , supply of hose cabinet box of 18 swg m.s.sheet with glass to accommodate hose reel drum with ruber pipe with nozzle. 2 nos. rrl hose and 1 no. branch pipe with nozzle , fixing, installation, testing & commissioning of hose cabinet box of 18 swg m.s.sheet with glass to accommodate hose reel drum with ruber pipe with nozzle. 2 nos. rrl hose and 1 no. branch pipe with nozzle , supply of air cushion tank ( 2000x1000 ) mm. , fixing, installation, testing & commissioning of air cushion tank ( 2000x1000 ) mm. , supply of air release valve. , fixing, installation, testing & commissioning of air release valve. , supply of nrv complete with flanges, gasket and nut bolts. 100 mm , fixing, installation, testing & commissioning of nrv complete with flanges, gasket and nut bolts. , supply of pressure gauge with gauge cock , fixing, installation, testing & commissioning of pressure gauge with gauge cock , supply of electrical motor driven fire pump suitable for automatic operation consisting of following : ( terrace pump ) ( make : kirloskar / mather+platt ) ( a ) horozontally mounted, split casing, centrifugal fire pump complete for delivery of under mentioned discharge against desired mentioned head so as to ensure a minimum pressure of 30 meter at the highest and farthest outlet at the specified flow cmplete with necessary strainers, pressure gauge including bypass arrangement for periodic testing of the working of the pumpset with required length and size of medium class gi pipe and control valves for proper completion of work.the pump shall be capable of giving 150% of rated discharge at head not less than 65% of rated head.the pump shall be provided with mechanical seals. the impeller shall be enclosed type and accurately blanced dynamically.the pump casing shall be of cast iron, impeller shall be of bronze and shaft shall be of stainless steel. ( b ) squirrel cage, tefc induction motor suitable for 415 v, 3 phase having ip 55 protection and class b insulation for the above pump and flexible coupling with the pump.the motor shall b rated for continuous duty and shall have hp rating necessary to drive th pump at 150% of its rated discharge at 65% of rated head. © common bed plate of fabricated mild steel channel or cast iron type. ( d ) suitable cement concrete pump foundation and vibration clamping arrangement as required with foundation bolts, anti vibration pads, washers etc. ( e ) pressure switch for automatic operation of motor including necessary wiring upto control panel. ( f ) electrical control panel with starter, 3 pole motor protection category current limiting type mccb, indicating light, ammeter, voltmeter, selector switches, cts protective fuses, single phasing protection, dry suction cut off etc as requrd as per standard details.discharge :450 liter per minute head : 35 meter , installation, testing and commisioning of electrical motor driven fire pump suitable for automatic operation consisting of following : ( terrace pump ) ( make : kirloskar / mather+platt ) ( a ) horozontally mounted, split casing, centrifugal fire pump complete for delivery of under mentioned discharge against desired mentioned head so as to ensure a minimum pressure of 30 meter at the highest and farthest outlet at the specified flow cmplete with necessary strainers, pressure gauge including bypass arrangement for periodic testing of the working of the pumpset with required length and size of medium class gi pipe and control valves for proper completion of work.the pump shall be capable of giving 150% of rated discharge at head not less than 65% of rated head.the pump shall be provided with mechanical seals. the impeller shall be enclosed type and accurately blanced dynamically.the pump casing shall be of cast iron, impeller shall be of bronze and shaft shall be of stainless steel. ( b ) squirrel cage, tefc induction motor suitable for 415 v, 3 phase having ip 55 protection and class b insulation for the above pump and flexible coupling with the pump.the motor shall b rated for continuous duty and shall have hp rating necessary to drive th pump at 150% of its rated discharge at 65% of rated head. © common bed plate of fabricated mild steel channel or cast iron type. ( d ) suitable cement concrete pump foundation and vibration clamping arrangement as required with foundation bolts, anti vibration pads, washers etc. ( e ) pressure switch for automatic operation of motor including necessary wiring upto control panel. ( f ) electrical control panel with starter, 3 pole motor protection category current limiting type mccb, indicating light, ammeter, voltmeter, selector switches, cts protective fuses, single phasing protection, dry suction cut off etc as requrd as per standard details.discharge :450 liter per minute head : 35 meter , ( a ) horozontally mounted, split casing, centrifugal fire pump complete for delivery of under mentioned discharge against desired mentioned head so as to ensure a minimum pressure of 30 meter at the highest and farthest outlet at the specified flow cmplete with necessary strainers, pressure gauge including bypass arrangement for periodic testing of the working of the pumpset with required length and size of medium class gi pipe and control valves for proper completion of work.the pump shall be capable of giving 150% of rated discharge at head not less than 65% of rated head.the pump shall be provided with mechanical seals. the impeller shall be enclosed type and accurately blanced dynamically.the pump casing shall be of cast iron, impeller shall be of bronze and shaft shall be of stainless steel. , fixing & placing on terrace ( at all floor levels ) polyethylene water storage tank isi : 12701 marked indicating the bis license no. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fitting and base support for tank. [ sintex, electroplast, star, lotus or equivalent having valid isi license ] . , supply of halon free portable fire extinguishers as described below: , 4.5 kg carbon dioxide extinguisher, is marked, with high pressure discharge tube, horn, control valve, cce approved cylinder , 6 kg mono ammonium phosphate ( abc ) type cartridge operated extinguishers , 9 kg mono ammonium phosphate ( abc ) type cartridge operated extinguishers , providing, fixing, testing and commissioning of 50 litres ( trolley mounted ) mechanical foam type fire extinguisher. in hp mild steel cylinders isi marked tac approved fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully charged complete in all respects including wall suspension bracket / trolley mounted and confoming to is:910 . , providing, fixing, testing and commissioning of co2 type fire extinguisher of capacity 22.5 kg filled with co2 gas as per is 15222 with controll discharge mechanism fitted with hose, horn & trolleyconfirms to is 2878 bearing isi mark. co2 cylinder as per is 7285 , fixing, storing, handling, shifting, installation, testing and commissioning of halon free portable fire extinguishers as described below: , supply of fire related signages printed on photoluminescent u1000 aluminium sheet of 1.0 mm ( + 10% ) containing lumigen ii as base chemical, covered under uv stablized coating and of appropriate size for fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete. , fixing of fire related signages printed on photoluminescent u1000 aluminium sheet of 1.0 mm ( + 10% ) containing lumigen ii as base chemical, covered under uv stablized coating and of appropriate sizeincluding fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete in all respects as directed by engineer in charge. , supply ofci cover with frame light weight complete as perdesign size 600x600 mm , supply ofci cover with frame light weight complete as perdesign size 900x900 mm , boring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in is: 2800 ( part i ) , including collecting samples from different strata, preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, beyond 90 metre & upto 150 metre depth below ground level.drilling of 250 mm dia bore hole manually. , supply of unplasticized pvc medium well screen ( rms ) pipes with ribs, conforming to is: 12818, fittings & accessories etc. all complete, for all depths, as per direction of engineer in charge.150 mm nominal size dia , assembling, lowering and fixing in vertical position in bore well unplasticized pvc medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer in charge.150 mm nominal size dia , supply of stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , supply of gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , supply of coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of engineer incharge. , filling, spreading & leveling coarse sand, gravels & stone boulders of size range 1.5 mm to 20 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of engineer incharge. , transportation charges of drilling equipment including assembly and other material as required. , drilling of 675 mm. dia by rotary machine , supply of 350 mm. dia housing pipe ( 8 mm. thick ) , laying of 350 mm. dia housing pipe ( 8 mm. thick ) , supply of 200 mm. dia blind pipe ( 8 mm. thick ) , laying of 200 mm. dia blind pipe ( 8 mm. thick ) , supply of 200 mm. dia slotted pipe ( 8 mm. thick ) , laying of 200 mm. dia slotted pipe ( 8 mm. thick ) , supply of 350 mm. dia socket , fixing of 350 mm. dia socket , supply of 200 mm. dia socket , fixing of 200 mm. dia socket , supply of 200 mm. dia bail plug , fixing of 200 mm. dia bail plug , supply of 350 mm. dia well cap , fixing of 350 mm. dia well cap , supply of 350x200 mm. dia reducer. , fixing of 350x200 mm. dia reducer. , supply of 350 mm. dia housing clamp , fixing of 350 mm. dia housing clamp , supply of pee gravel 2 mm. 4 mm. in side of bore after lower and development as required as per direction of e / i. , filling of pee gravel 2 mm. 4 mm. in side of bore after lower and development as required as per direction of e / i. , development by air compressor including transportation. , development by o.p. unit including transportation. , supply of 7.5 hp ksb make submersible pump set model bpd 302 / 4+uami 150 / 6 / 22 203 ( s / d ) suitable for tube well capable of pumping clear and cold water free from chemical and directly coupled with ksb electric moter operating of 415 volt suitable for 3 phase 50 cycle a.c. supply of following duty condition 7.5 hp 6 stage pipe.a discharge of water in lpm 860 approx size of discharge outlet in 80 mm.b total head of pump set 45 m. , supply of finolex or equivalent isi marked submersible copper cable of size 2x3x2.5 sq. mm. , fixing of finolex or equivalent isi marked submersible copper cable of size 2x3x2.5 sq. mm. , supply of control panel cubical type wall mounted vermin proof with internal wiring duly enameled painted and mechanically finished having l&t of qul. male switch fuse unit with hrc fuses, ameter, boltmeter, selector switch, phase indicating lamp with bulbs, instrument fuses, power capcitor single phase preventor etc. complete set with supply of jyoti or eq. air break star delta motro starter suitable for above submersible pump set. , supply of 80mm dia m.s. column pipe of class c both and socketed with heavy sockets in 3 / 6 meter length and one end flanged complete with interlocking arrangements. , lowering of 80mm dia m.s. column pipe of class c both and socketed with heavy sockets in 3 / 6 meter length and one end flanged complete with interlocking arrangements. , supply of 80mm dia m.s. column pipe clamps with nut, bolts, packing etc. , lowering of 80mm dia m.s. column pipe clamps with nut, bolts, packing etc. , supply of 80mm dia c.i. double flanged isi mark reflex valve of updadhya or equ. make. , fixing ofc.i. double flanged reflex valve , supply of 80mm dia c.i. double flanged isi mark sluice valve with hand wheel of upadhya or equ. make. , supply of 100 mm dia c.i. double flanged isi mark sluice valve with hand wheel of upadhya or equ. make. , supply of 150mm dia c.i. double flanged isi mark sluice valve with hand wheel of upadhya or equ. make. , fixing of 80 / 100 / 150 mm dia c.i. double flanged isi mark sluice valve with hand wheel , supply of c.i. double flanged bend of 80mm dia , fixing of c.i. double flanged bend of 80mm dia i / c cost of labour. , supply of 80mm dia c.i. tee heavy quality i / c cost of material. , fixing of 80mm dia c.i. tee heavy quality , supply of guru / fibing or equivalent make pressure gauge. , fixing of pressure gauge. , erection & commissioning of pumping plants complete along with electric wiring. , supply of steel wire rope of 1 / 2 size , fixing of steel wire rope of 1 / 2 size , s / b of 600mm x 600 mm x 6.0 mm g.i. plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia g.i. pipe and funnel for watering and one earthing lead on one no. 8 to 10 swg gi wite in 15mm dia g.i. pipe up to switch board ( from appron to switch board the cost of g.i. , pipe and g.i. wire will be extra ) 30 cm square c.i. frame with hinged cover masonry housing alternate layers of charcoal. coke and salt at least 150mm thick alround etc. as per directions of e / i complete in all respects as per drawing. , s / f of one number 8 to 6 swg g.i. wire in 15mm dia g.i. pipe for earthing, laid in ground or in wall duly concealed includingn the cost of cement, sand labour. t&p other material required for proper completion of the work as directed at site. , s / f of aluminium conductor pvc insulated armoured, served, sheathed cable 1100 volts grade16 sqmm x 4 core , fixing of aluminium conductor pvc insulated armoured, served, sheathed cable 1100 volts grade at a depth of 750mmbelow ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and on top.on surface the cable run shall be fixed on m.s. clamps etc. of suitable size or as directed by e / i complete in all respects the armoring of the cable shall be properly connected with the earth conductor by clamps etc.16 sqmm x 4 core , supply of 500 kva. 11 / 0.433 kv, 3phase, 50hz, dyn 11, oil type, ( uppcl approved make ) copper wound transformer with off load tap changing arrangement on hv side in steps of + / 2.50%, + / 5% & 7.5% , having cable end boxes on hv sideand 800 amp. bus trunking arrangement on lv side complete with all accessories i / c first filling of filtered dehydrated oil and confirming to is 2026 ( part 1 to part 5 ) & as per specification attached complete in all respects as required at site. , installation, testing and commissioning of 500 kva. 11 / 0.433 kv, 3phase, 50hz, dyn 11, oil type, ( uppcl approved make ) copper wound transformer with off load tap changing arrangement on hv side in steps of + / 2.50%, + / 5% & 7.5% , having cable end boxes on hv sideand 800 amp. bus trunking arrangement on lv side complete with all accessories i / c first filling of filtered dehydrated oil and confirming to is 2026 ( part 1 to part 5 ) & as per specification attached complete in all respects as required at site. , supply of 3 core standered aluminium conduktor xlpe ( cross linked polyethylene ) insulated pvc bedded, galvanised flat steel strip armoured cables confirming to i.s. 7098 ( part ii with latest amendments ) 11 kv grade 150sq. mm 3 core , laying of 3 core standered aluminium conduktor xlpe ( cross linked polyethylene ) insulated pvc bedded, galvanised flat steel strip armoured cables confirming to i.s. 7098 ( part ii with latest amendments ) 11 kv grade at a depht of 900 mm below ground level over a cushion of 100 mm thick fine river sand all around and protected with well burnt bricks in sides and on the top put across. thearmouring of cable shall be properly connected with earth condutor by clamps etc.150sq. mm 3 core , supply of 3 core 240sq.mm. xlpe aluminium conductor cable of 11 kv grage as required. , making indoor cable end jointing with cast resin compound, including lugs and other jointing materials, for 3 core 240sq.mm. xlpe aluminium conductor cable of 11 kv grage as required. , making outdoor cable end jointing with cast resin compound, including lugs and other jointing materials, for 3 core 240 sq.mm. xlpe aluminium conductor cable of 11 kv grage as required. , supply and burying of 40mm dia x 4.5 metres long g.i. pipe vertically for earthing having 12mm dia. holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of no. 6 to 8 swg gi wire in g.i. pipe up to appron ( and from appron to switch board the cost of g.i. wire and pipe will be extra ) upto switch board, 30cm square c.i. box with hinged cover masonary enclosure, funnel at top, alternate layers of charcoal / coke and salt at least 150mm thick alround etc. as per directions of engineer in charge complete in all respects as per drawing. , supply and burying of 600mm x 600 mmx6mm g.i. plate, vertically for earthing with its top atleast 3 mts. below ground level complete with 20mm g.i.pipe and funnel for watering and two earthing leads of no.8to10swg g.i.wire in 15mm diag.i. pipe upto switch board ( from apron to switch board the cost of g.i. pipe and g.i. wire will be extra ) 30cm. square c.i. frame with hinged cover, masonary housing, alternate layers / of charcoal / coke and salt at least 150mm thick alround etc. complete in all respects. , supply and burying of 600mm x 600mm x 3 mm copper plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia g.i pipe and funnel for watering and one earthing lead ofone no. 8swg copper wire in 15 mm dia g.i pipe up to switch board ( from appron to switch board the cost of g.i pipe and copper wire will be extra ) 30 cm square c.i frame with hinged cover masonry housingalternate layers of charcoal / coke and salt atleast 150mm thick alround etc. as per directions of engineer in charge complete in all respects. , supply and laying of 32mm x 6mm g.i. strip from earth electrode directly in the ground as required complete in all respects. , supply and laying of 32mm x 6 mm copper strip from earth electrode directly in the ground as required complete in all respects.. , supply and laying of 25mm x 3mm g.i. strip from earth electrode directly in the ground as required complete in all respects. , supply and fixing of one number 8 swg g.i wire in 15mm dia. g.i pipe for earthing laid in ground or in wall duly concealed including the cost of cement, sand, labour, t&p other material required for proper completion of the work as directed at site. , supply of aluminium conducter, pvc insulated armoured, served, sheeted cable 1000 bolts grade , 300 sqmm3.5 core , 185 sqmm3.5 core , 150 sqmm3.5 core , 35 sqmm3.5 core , 25 sqmm3.5 core , 16 sqmm4 core , 10 sqmm4 core , 16 sqmm2 core , 10 sqmm2 core , 6 sqmm2 core , laying of aluminium conducter, pvc insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the cable run shall be fixed on m.s. clamps etc. of suitable size. from 6 sqmm 2 core to 300 sqmm3.5 core , supply of brass nickle plated compression gland for pvc insulated & armoured served sheathed, underground cable including rubber ring etc. complete , 300 sqmm3.5 core , 185 sqmm3.5 core , 150 sqmm3.5 core , 35 sqmm3.5 core , 25 sqmm3.5 core , 16 sqmm4 core , 10 sqmm4 core , 16 sqmm2 core , 10 sqmm2 core , 6 sqmm2 core , fixing of brass nickle plated compression gland for pvc insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respects. the armouring of the cable shall be properly connected with the earth as per direction of eic. from 6 sqmm 2 core to 300 sqmm3.5 core , supply of palm / pin type copper tin plated cables sockets ( lugs ) to the cable leads, insuslating with tape , 300 sqmm , 185 sqmm , 150 sqmm , 95 sqmm , 70 sqmm , 35 sqmm , 25 sqmm , 16 sqmm , 10 sqmm , 6 sqmm , 4 sqmm , fixing of palm / pin type copper tin plated cables sockets ( lugs ) to the cable leads, insuslating with tape and making of connections etc. complete in all respects as per direction of engineer incharge. from 4 sqmmto 300 sqmm , supply of 7 mtr gi octagonal pole of approved make ( top dia 70mm, bottom dia 130 mm and base plate 12 mm thik ) having 3mm thikness with single arm bracket ( 1 mtr length ) including the cost of foundation bolts, required t&p complete in all respect. , fixing of 7 mtr gi octagonal pole of approved make ( top dia 70mm, bottom dia 130 mm and base plate 12 mm thik ) having 3mm thikness with single arm bracket ( 1 mtr length ) on rcc foundation including the cost of foundation, foundation bolts, excavation & back filling and required t&p complete in all respect. , supply of led street light fitting having die cast aluminium body and diffuser with driver set suitable for 45 watt to 50 watt. confirming to ip 66 and above protection complete in all respect. , fixing of led street light fitting having die cast aluminium body and diffuser with driver set suitable for 45 watt to 50 watt. confirming to ip 66 and above protection complete in all respect. , supply of 6 amp to 32 amp dp mcb ( 10ka ) ( c curve ) for poles , fixing of 6 amp to 32 amp dp mcb ( 10ka ) ( c curve ) for poles , supply of decorative 40 to 45 watt led post top indirect light luminaire having pressure die cast aluminium body and clear glass with driver set confirming to ip 65 and above protection complete in all respect. , fixing of decorative 40 to 45 watt led post top indirect light luminaire having pressure die cast aluminium body and clear glass with driver set confirming to ip 65 and above protection complete in all respect. , supply offollowing capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contractors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn complete in all respect.25 amp spn , fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contractors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn complete in all respect.25 amp spn , supply of bakelite sheet 3 mm thick of suitable size & connector , fixing of bakelite sheet 3 mm thick of suitable size & connector , supply of m.s. pipe ( class b is : 1239 ) pole suitable for fixing 70 watt. hpsv post top including 4 pole cable junction box with 5 amp. rewireablefuse fitting and 5 amp. switch on laminated cover and m.s. box complete with water tight cover and 450x450x450mm base above ground and 2x4sqmm aluminium wire from cable box to lamp for connection including painting the pole on primer coats and necessary reducers on thetop of pole for fixing of post top lantern. 65mm dia 4m long ( 3m above ground and 1 m below ground ) . , fixing of m.s. pipe ( class b is : 1239 ) pole suitable for fixing 70 watt. hpsv post top including 4 pole cable junction box with 5 amp. rewireablefuse fitting and 5 amp. switch on laminated cover and m.s. box complete with water tight cover includingmasonary / pcc ( 1:3:6 ) work for erecting the pole and 450x450x450mm base above ground and 2x4sqmm aluminium wire from cable box to lamp for connection including painting the poleby an approved shade on primer coats and necessary reducers on thetop of pole for fixing of post top lantern.the work shall be complete as required up to the satisfaction of engg. in charge.65mm dia 4m long ( 3m above ground and 1 m below ground ) . , making of following size of cable chamber made of 230 mm thick brick work in cement mortar ( 1 cement : 6 sand ) with pcc 100 mm thick pcc base plastering of inner and outer surface with cement mortar including providing of heavy duty c.i cover complete with digging, refilling and removal of surplus soil complete as required. material cost will be paid saperately.900 mm x 900 mmx 1000 mm deep , supply of mv danger notice plate of 200 mm x 150 mm made of mild steel at least 2mmthick &vitreousenamelledwhiteon bothsides and withinscription insignalred colouronfront side as required. , supply of ht danger notice plate 250 mm x 200 mm made of mild steel at least 2mmthick &vitreousenamelledwhiteon bothsides and withinscription insignalred colouronfront side as required. , fixing of mv / ht danger notice plate 250 mm x 200 mm made of mild steel at least 2mmthick &vitreousenamelledwhiteon bothsides and withinscription insignalred colouronfront side as required. , supplying of fire buckets, round bottom made of g.i. sheet 9 11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of engineer in charge. , fixing of fire buckets, round bottom made of g.i. sheet 9 11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of engineer in charge. , supply of 1800 mm x 900 mm x 12 mm thick chequered rubber matting of tested quality , layingof 1800 mm x 900 mm x 12 mm thick chequered rubber matting of tested quality , supply of danger board fabricated from 10 gauge ms sheet as per ie rules , fixing of danger board fabricated from 10 gauge ms sheet as per ie rules , supply of shock treatment chart ( prescribed under i.e.rules ) duly framed with glass and supported from back with hard board or soft board. , fixing of shock treatment chart ( prescribed under i.e.rules ) duly framed with glass and supported from back with hard board or soft board with supply of all labour t & pfor proper completion of work. , supply of fire extinguishers, abc type 4.00 kg. capacity ( isi marked is : 15683 & tac approved ) complete with initial charges and wall bracket, , supply of co2 typefire extinguishers, 4.50 kg. capacity ( isi marked is : 2878 & tac approved ) complete with initial charges and wall bracket, , fixing of fire extinguishers, abc type 4.00 kg. & co2 type 4.5 kg. capacity complete with initial charges and wall bracket, along with supply of all labour for proper completion of work. , supply of water closet squatting pan ( indian type w.c. pan ) with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) conforming to is:7231, parryware / hindware / seabird / orient ( coral ) with all fittings and fixtures complete.white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests , fixing of water closet squatting pan ( indian type w.c. pan ) with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) conforming to is:7231, parryware / hindware / seabird / orient ( coral ) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests , supply of white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) , conforming to is : 7231, parryware / hindware / seabrid / orient ( coral ) with all fittings and fixtures complete.w.c. pan with isi marked black solid plastic seat and lid , fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) , conforming to is : 7231, parryware / hindware / seabrid / orient ( coral ) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : w.c. pan with isi marked black solid plastic seat and lid , supply of white vitreous china extended wall mounting water closet of size 780x370x690mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre / 6 litre ( adjustable to 4 litre / 8 litres ) , including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. , fixing of white vitreous china extended wall mounting water closet of size 780x370x690mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre / 6 litre ( adjustable to 4 litre / 8 litres ) , including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. , supply of white vitreous china wash basin with c.i. brackets painted white, 15 mm c.p. brass pillar taps, c.p. brass chain with rubber plug, 32mm c.p. brass waste of standerd pattern. , a ) white vitreous china wash basin size 630x450 mm with a pair of 15 mm c.p. brass pillar taps , b ) white vitreous china surgeon type wash basin of size 660x460 mm with single 15 mm c.p. brass pillar taps with elbow operated levers isi marked , fixing of white vitreous china wash basin with c.i. brackets painted white, 15 mm c.p. brass pillar taps, c.p. brass chain with rubber plug, 32mm c.p. brass waste of standerd pattern including cutting & making good the walls wherever required. , a ) white vitreous china wash basin size 630x450 mm with a pair of 15 mm c.p. brass pillar taps , b ) white vitreous china surgeon type wash basin of size 660x460 mm with single 15 mm c.p. brass pillar taps with elbow operated levers isi marked , supply of p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. , semi rigid pipe , 32 mm dia , 40 mm dia , fixing of p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. , semi rigid pipe , 32 mm dia , 40 mm dia , supply of 600x450mm bevelled edge mirror of superior glass ( of approved quality ) complete with 6mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. , fixing of 600x450mm bevelled edge mirror of superior glass ( of approved quality ) complete with 6mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. , supply of stainless steel aisi 304 ( 18 / 8 ) kitchen sink as per is : 13983 with c.i. brackets and stainless steel plug 40mm including painting of fittings and brackets, kitchen sink with drain board size 510x1040 mm bowl depth 250mm , fixing of stainless steel aisi 304 ( 18 / 8 ) kitchen sink as per is : 13983 with c.i. brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherrerever required.kitchen sink with drain board size 510x1040 mm bowl depth 250mm , supply of white vitreous china flat back half stall urinal of size 580*380*350mm with white pvc automatic flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps ( all in d.p. brass ) with waste fitting as per is : 2556, c.i. trap with outlet grating and other couplings in c.p. brass including painting of fittings. , range of three half stall urinals with 10 litre pv.c. automatic flushing cistern. , range of two half stall urinals with 5 litre pv.c. automatic flushing cistern. , range of single half stall urinals with 5 litre pv.c. automatic flushing cistern. , fixing white vitreous china flat back half stall urinal of size 580*380*350mm with white pvc automatic flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps ( all in d.p. brass ) with waste fitting as per is : 2556, c.i. trap with outlet grating and other couplings in c.p. brass including painting of fittings and cutting and making good the walls and floors wherever required: , range of three half stall urinals with 10 litre pv.c. automatic flushing cistern. , range of two half stall urinals with 5 litre pv.c. automatic flushing cistern. , range of single half stall urinals with 5 litre pv.c. automatic flushing cistern. , fixing of stone slab table rubbed, edges rounded and polished of size 75x50cm deep and 1.8cm thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 ( 1cement: 2coarse sand: 4graded stone aggregate 6mm nominal size ) as per direction of engineer in charge and finished smooth.granite stone of approved shade , supply of unplasticised pvc connection pipe with brass unions , 45 cm length , 15 mm nominal bore , fixing of unplasticised pvc connection pipe with brass unions , 45 cm length , 15 mm nominal bore , supply of c.p. brass bib cock of approved quality conforming to is:8931 a ) 15 mm nominal bore , fixing of c.p. brass bib cock of approved quality conforming to is:8931v a ) 15 mm nominal bore , supply of c.p. brass long body bib cock of approved quality conforming to is standards andweighing not less than 690 gms.a ) 15 mm nominal bore , fixing of c.p. brass long body bib cock of approved quality conforming to is standards andweighing not less than 690 gms.a ) 15 mm nominal bore , supply of c.p. brass angle valve for basin mixer and gyser points of approved quality conforming to is:8931a ) 15 mm nominal bore , fixing of c.p. brass angle valve for basin mixer and gyser points of approved quality conforming to is:8931a ) 15 mm nominal bore , supply of c.p. brass shower rose with 15 or 20mm inlet 150 mm diameter , fixing of c.p. brass shower rose with 15 or 20mm inlet150 mm diameter , supply of c.p. brass stop cock ( concealed ) of standard design and of approved make conforming to is:8931: 150 mm diameter , fixing of c.p. brass stop cock ( concealed ) of standard design and of approved make conforming to is:8931: 150 mm diameter , supply of ptmt bottle trap for wash basin and sink.bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms , fixing of ptmt bottle trap for wash basin and sink.bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms , supply of ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. , fixing of ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. , supply of ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms , fixing of ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms , supply of unplasticised pvc pipe clips of approved design to unplasticised pvc pipes by means of 50x50x50 mm hard wood plugs, screwed with ms screws , 110mm , 90mm , fixing of unplasticised pvc pipe clips of approved design to unplasticised pvc pipes by means of 50x50x50 mm hard wood plugs, screwed with ms screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand ) and making good the wall etc. complete. , 110mm , 90mm , laying of cement concrete 1:5:10 ( 1 cement : 5 coarse sand : 10 graded stone aggregate 20mm nominal size ) around p.v.c soil and waste pipe including bed concrete as per standard design ( embedded in the flooring / ground ) , 100 / 75 mm dia , supply of wall face unplasticised rigid pvc rain water pipes conforming to is: 13592 type a110 mm , fixing on wall face unplasticised rigid pvc rain water pipes conforming to is: 13592 type a including jointing with seal ring conforming to is: 5382 leaving 10mm gap for thermal expansion. 110 mm , supply of wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is:13592. , bend 87.5 degree , 110 mm bend , shoe ( plain ) 110 mm shoe , fixing of wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is:13592type a including jointing with seal ring conforming to is:5382 leaving 10mm gap for thermal expansion. , bend 87.5 degree , 110 mm bend , shoe ( plain ) 110 mm shoe , supply of inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. , fixing of the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. , supply of unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with ms screws of required length. 110 mm , fixing of unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with ms screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand ) and making good the wall etc. complete.110 mm , making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size ) over pvc sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 ( 1 cement : 3 coarse sand ) and a coat of neat cement, punning, rounding the edges and making and finishing the outlet complete. , supply of chlorinated polyvinyl chloride ( cpvc ) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i / c fixing the pipe with clamps at 1.00m spacing. , 20mm dia nominal outer dia pipes , 25mm dia nominal outer dia pipes , 32mm dia nominal outer dia pipes , fixing of chlorinated polyvinyl chloride ( cpvc ) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i / c fixing the pipe with clamps at 1.00m spacing.this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of engineer in charge. , concealed work including cutting chases and making good the walls etc. , 20mm dia nominal outer dia pipes , 25mm dia nominal outer dia pipes , 32mm dia nominal outer dia pipes , supply of gi pipes complete with gi fittings and clamps. , 15mm dianominal bore , 20mm dianominal bore , 25mm dia nominal bore , 32mm dia nominal bore , 40mm dia nominal bore , 50mm dia nominal bore , 65mm dia nominal bore , fixing of gi pipes complete with gi fittings and clamps, including cutting and making good walls etc. ( internal work ) . internal work exposed on wall , 15mm dianominal bore , 20mm dianominal bore , 25mm dia nominal bore , 32mm dia nominal bore , 40mm dia nominal bore , 50mm dia nominal bore , 65mm dia nominal bore , painting of gi pipes and fittings with synthetic enamel paint over a ready mixed priming coat, both of approved quality for new work. , 15mm dia nominal bore , 20mm dia nominal bore , 25mm dia nominal bore , 32mm dia nominal bore , 40mm dia nominal bore , 50mm dia nominal bore , 65mm dia nominal bore , supply of gi union in gi pipes , 15mm dia nominal bore , 20mm dia nominal bore , 25mm dia nominal bore , 32mm dia nominal bore , 40mm dia nominal bore , 50mm dia nominal bore , 65mm dia nominal bore , fixing of gi union in gi pipes including cutting and threading the pipe and making long screws etc. complete ( new work ) . , 15mm dia nominal bore , 20mm dia nominal bore , 25mm dia nominal bore , 32mm dia nominal bore , 40mm dia nominal bore , 50mm dia nominal bore , 65mm dia nominal bore , supply of gun metal gate valve with wheel of approved quality. , 25mm dia nominal bore , 32mm dia nominal bore , 40mm dia nominal bore , 50mm dia nominal bore , 65mm dia nominal bore , fixing of gun metal gate valve with wheel of approved quality. , 25mm dia nominal bore , 32mm dia nominal bore , 40mm dia nominal bore , 50mm dia nominal bore , 65mm dia nominal bore , supply of brass stop cock of approved quality. , b ) 20 mm nominal bore , fixing of brass stop cock of approved quality. , b ) 20 mm nominal bore , supply of terrace ( at all floor levels ) polyethylene water storage tank isi : 12701 marked indicating the bis license no. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fitting and base support for tank. [ sintex, electroplast, star, lotus or equivalent having valid isi license ] . , fixing & placing of terrace ( at all floor levels ) polyethylene water storage tank isi : 12701 marked indicating the bis license no. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fitting and base support for tank. [ sintex, electroplast, star, lotus or equivalent having valid isi license ] . , supply of glazed stoneware pipes grade a100mm dia sw pipe , laying and jointing glazed stoneware pipes grade a with stiff mixture of cement mortar in the proportion of 1:1 ( 1 cement : 1 fine sand ) including testing of joints etc. complete.100mm dia sw pipe , laying cement concrete 1:5:10 ( 1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size ) all rounds.w. pipes including bed concrete as per standard design 100mm dia sw pipe , supply of square mouth s.w. gully trap grade‘a’ complete with c.i. grating, water tight c.i. cover with frame of 300 x300 mm size ( inside ) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 150 x 100 mm size p type , fixing of square mouth s.w. gully trap grade‘a’ complete with c.i. grating, brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size ( inside ) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design150 x 100 mm size p type , supply of floor and wall face ringfit upvc astral ultradrain conventional system for soil and waste water pipes conforming to ( hsn code: 3917 ) type b ( i ) double socketed pipes. , a ) 110mm dia p.v.c. pipe , b ) 90mm dia p.v.c. pipe , fixing of floor and wall face ringfit upvc astral ultradrain conventional system for soil and waste water pipes conforming to ( hsn code: 3917 ) type b including jointing with seal ring. ( i ) double socketed pipes. , a ) 110mm dia p.v.c. pipe , b ) 90mm dia p.v.c. pipe , supply of upvc floor trap of self cleansing designwith cp jalicomplete in all respects. ( make : supreme / finolex / prince ) p trap type floor trap 110 x 90mm , fixing of upvc floor trap of self cleansing designwith cp jalicomplete in all respects. ( make : supreme / finolex / prince ) p trap type floor trap 110 x 90mm , supply of clean out plug ( astral ) , fixing of clean out plug ( astral ) , supply ofterminal guard. , a ) 110mm , b ) 90mm , fixing of terminal guard. , a ) 110mm , b ) 90mm , supply of wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes. , 110mm bend , 90 mm bend , 110mm coupler , 90mmcoupler , 110x110x110 mm single tee with door , 90x90x90 mm single tee with door , fixing of wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. , 110mm bend , 90 mm bend , 110mm coupler , 90mmcoupler , 110x110x110 mm single tee with door , 90x90x90 mm single tee with door , supply of 1.50 sqmm frlsh pvc insulated single core copper conductor cable , supply of 2.50 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable , supply of 4.00 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable , supply of 6.00 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable , supply of 10 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable , supply of 16 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable , supply of 25 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable , supply of hexagonal / round gp fan box of approved make made up of 1 mm thick isi marked gp sheet spot welded four to eight holes of 25.4 mm for pipe entry of the box duly screewed fitted with 300 mm round zink coated ms bar x 12 mm. , supply of ceiling fan with fan motor of ac permanent insulation, capacitor rating conforming to bee 5 star. the ratrd voltage220 / 240 volts, 50 hz, single phase, ac the fan assemble should consists of down road blades, shackle canopies with double ball bearing system – 1200 mm sweep , supply of electronic fan regulator ( modular ) 120 280 v isi marked , supply of led tube light with metal heavy duty box type batten light fitting 2x 22 watt suitable for 2x22 watt polycarbonate tube light including tube etc suitable for both surface. , supply of led tube light with metal heavy duty box type batten light fitting 1x 22 watt suitable for 1x22 watt polycarbonate tube light including tube etc suitable for both surface. , supply of recess / surface mounting round 10 to 15 watt, cut out 125 mm, height min 40 mm, led downlighter having powder coated die cast aluminium housing with heat sink, diffuser / reflector and driver set, suitable for 24 hr continuousoperation , supply of single led light wall bracket on matching mdfeg board base , water tight oblong 10 watt led bulkhead luminery with driver set conforming to ip 65 and above protection complete. , supply of surface / flush mounting distribution boards with additional metal door without mcb complete. ( cat a ) , 4 way tpn , 6 way tpn , 8 way tpn , supply of 6 amp to 32 amp ( 10 ka ) sp mcb ( cat a ) , supply of following mcbs , 40 amp. fp mcb ( cat a ) , 63 amp. fp mcb ( cat a ) , 40 amp. tp mcb ( cat a ) , 63 amp. tp mcb ( cat a ) , supply of surface / flush mounting v tpn distribution boards with additional metal door without mcb complete. 4 way v tpn , supply of following mccbs , 63 amp. fp mccb ( cat a ) , 100 amp. fp mccb ( cat a ) , 125 amp. fp mccb ( cat a ) , 160 amp. fp mccb ( cat a ) , supply of power plug with 15 a / 250 v flush type switch and 5 pin 15 a / 250 v flush type universal socket in suitable ms box 175mmx100mmx50mm size ( modular ) , supply of single pole mcbs blanking plate complete , supply of gi plate for earthing size 600 mm x 600mm x 6 mm , supply of gi pipe 20 mm dia , supply of gi wire 8 to 10 swg , supply of ci frame ( 30 sqcm ) with hinged cover , supply of gi strip for earthing purpose 25 mmx 3 mm , supply of aluminium conductor pvc insulated armoured, served, sheeted cable 1000 volts , 95 sqmm 3.5 core , 70 sqmm 3.5 core , 50 sqmm 3.5 core , 35 sqmm 3.5 core , 25 sqmm 3.5 core , 10 sqmm 4 core , supply of brass nickle plated compression gland for pvc insulated and armoured served sheeted underground cable including rubber ring , 95 sqmm 3.5 core , 70 sqmm 3.5 core , 50 sqmm 3.5 core , 35 sqmm 3.5 core , 25 sqmm 3.5 core , 10 sqmm 4 core , supply of palm / pin type copper tin plated cable sockets ( lugs ) to the cable leads, insulating with tape , 95 sqmm , 70 sqmm , 50 sqmm , 35 sqmm , 25 sqmm , 16 sqmm , 10 sqmm , 6 sqmm , supply of gi box alonwith modular base and cover plate for modular switches in recess1 or 2 module ( 75 mmx75 mm ) , supply of telephone socket outlet ( modular ) , supply of tv antenna socket outlet ( modular ) , supply of bell push ( modular ) , supply of call bell / buzzer suitable single phase 230 v , supply of telephone cable following pair 0.5 sqmm fr pvc insulated annealed copper conductor, unarmoured , 2 pair , 10 pair , 20 pair , supply of co axial tv cable rg 6 grade 0.7 mm solid copper conductor pe insulated sheeted with fine tinned copper braid and protected with pvc sheet , supply of 10 pair junction boxes for floors and building with krone connectors , supply of 20 pair junction boxes for floors and building with krone connectors , supply of 50 pair junction boxes for floors and building with krone connectors , supply of exhaust fan of ac 230 / 250 v, 50 hz including nuts & bolts, mounting frame and other accessories.300 mm sweep , supply of energy meter ( 3 phase ) and other accessories. , supply of wall fanof ac 230 / 250 v, 50 hz including nuts & bolts, mounting frame and other accessories. 450 mm sweep , supply of exhaust fan of ac 230 / 250 v, 50 hz including nuts & bolts, mounting frame and other accessories.450 mm sweep , supply of weired decorative mirror light suitable 9 watt led with lamp complete , supply of factory weired integral led flood light luminaries with die cast aluminium housing built with driver set suitable for 40 to 50 watt confoming to ip 65 / 66 protection complete. , supply of swiches ( modular ) 5 amp , supply of sockets ( modular ) 5 amp , supply of pvc conduit pipe 25 mm dia , supply of round sheet , supply of ceiling rose , supply of holder for bulbs , fixing of main lt panel , fixing of main em panel , fixing of sub panel , fixing of sub em panel , fixing of capacitor panel 150kvar , fixing of feeder piller , fixing of street feeder piller , supply of coarse sand , supply of cement50 kg , supply of brick m150 , supply of stone grit 20 mm , supply of stone ballast 40 mm , supply of tor steel 8 mm dia , supply of tor steel 10 mm dia , supply of tor steel 12 mm dia , supply of tor steel 16 mm dia , supply of tor steel 20 mm dia , supply of tor steel 25 mm dia , supply of ms fabrication for door window and ventilator , supply of water proofing chemical cico tapecrete p151 , supply of y shaped angle iron post 40x40x6 , supply of kota stone 22 mm thick , supply of vitriried floor tile 8 to 10 mm thick in 600x600 mm size , supply of wall tile glazed / ceramic floor tiles , supply of ss railing 304 grade , supply of ms collapsible channel , supply of rolling shutter with ball bearing , supply of granite , supply of cinder , supply ofchequred tile 300x300 mm size , supply of ms gate made of ms hollow sections , supply of interlocking pavers 80 mm m30 mpa , labour charge for construction of rcc over head tankas per design and drawing &directions of engineer in charge....

Kisan Sahkari Chini Mills Limited - Uttar Pradesh

37948558 supply of mechanical circulator for 60 ton pan with planetary gear motor for season 2023 24 , tender for the supply of mechanical circulator 60 ton pan with erection & commissioning and trail & testing as per specification mentioned below for season 2023 24 , supply scope technical specification of mechanical circulator for capacity 60 ton vaccum pan of b massecuite 01 no., bearing with planatory general motor, vfd pannel & cable etc. mechanical circulator to suit for60tonscapacity , vacuum pan (top mounted ) having a shaft machine from 150 mm dia en 8 in three piece couple through a set of fixed ms coupling with gunmetal bush . the lower shaft shall of ms drum duly machined fitted with necessary ss vanes thickness 16 mm& a guide bearing at other end & supported with center down take of pan calandria . the upper shaft shall be supported with cast steel housing fitted with thrust roller spherical roller bearing & gun metal bush with complete sealed & leak proof with mechanical seal fitted with flexible coupling for both output & input shaft complete with suitable vertical planetary gear box & suitable motor, 1440 rpm vertical flange mounted motor. the final rpm of mechanical circulator will be 48 . the middle shaft will be supported with pan bodyand bottom shaft will be supported with downtakeof pan . motor required – for60ton pan – 60 hp , 1440 rpm vertical flange mounted motor planetary gearbox make – kavastu/ top gear motor make – abb / crompton / siemens variable frequency device & control panel make – compton / siemens / abb supporting staging the supporting staging & structure provided from pan floor & the bed plate &cast steel housing with spherical roller bearingwill be fitted with supporting structure & also platform & railing will be provided by party. `...

Military Engineer Services - Uttar Pradesh

37602723 repair/maintenance of joinery and allied items in md and otm accn under age b/r i at babina cantt 1 taking down chowkhat or frames with shutters (without taking off shutters from the frame) not exe 1.5 sqm each etc complete all as specified and as directed 2 taking down chowkhat or frames with shutters (without taking off shutters from the frame) exe 1.5 sqm but not exc 4 sqm each etc complete all as specified and as directed. 3 taking down shutters of any description n.exc 1 sqm each etc complete all as specified and as directed 4 taking down shutters of any description exc 1 sqm and n.exc 2 sqm each etc complete all as specified and as directed 5 refixing shutter of any description exc 1 sqm but n exc 2 sqm each in same opening etc complete all as specified and as directed 6 refixing shutter of any description exc2 sqm each in same opening etc complete all as specified and as directed 7 s&f solid pvc frame of size 50mmx47mm made out of 5mm plain colour pvc sheet reinforced with m.s. square tube, etc complete all as specified and as directed 8 s&f factory made solid panel pvc door shutter 30mm thick (style) constiting of frame made out of ms tubes for top & bottom rails, ms frame shall be covered with heat moulded plain colour pvc c channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and palin colour pvc sheet for top rail lock rail & botom rail on either side and as gap insert for top rail bottom rail, panelling of plain colour pvc sheet to be fitted in the ms frame welded/selaed to the stiles & rails with suitable pvc sheet beading and joined together with solvent cement and fix in the frame at site complete all as specified and as directed 9 s&f factory made solid pvc moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded pvc sheet on the front face & 2mm plain colour pvc sheet on back face, supplying & fixing in frame at site as per specification & drawing etc complete all as specified and as directed 10 m&l, anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified 11 m&l foraluminium powder coated glazed door shutter( single leaf ) fabricated out of approved powder coated aluminium sections , shutter havingbottom rail of section size 114.50 mm x 44.50 mm x2.0 mm thick section, middle and top rail of section 84.50 mm x 44.50 x 2 mm thick section andstyles of section size84.50 mm x 44.50 mm x 2 mm thickand s & f 5.5 mm thick tinted glass in panel of shutter fixed with glazing clips , rubber gasket and powder coated aluminium snap beading so as to make air tight and including s & f powder coated butt hinges type c 1,100 mm size 3 nos per shutter , powder coated aluminium handle of 150mm size 2 nos (one on each side of shutter) , powder coated aluminium tower bolt of size 200 mm ( 2 nos ) per shutter ,mortise lock , brass body ,6 levers ( 1 no) with duplicate keys, aluminium (extruded section) hydraulic door closer regulated designation no 3 universal type ( 1 no) & floor door stopper ( 140 mm ) overall ,aluminium body 1 no on each shtteretc complete all as specified and as directed. note: (i) shutter ( glazed ) shall be fixed on frame of required size and shall be measured seperately (iii) cost of all fittings & fixture shall deemed to be included in unit quoted rate by the tenderer . note : the minimum thickness of powder coating shall be 50 micron . 12 m&l forpowder coated auminium glazed window / ventilator shutter, fixed type ,without sash bars usingapproved powder coated aluminium sections weighing 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws etc completeall as specified and as directed. note : (i) the minimum thickness of powder coating shall be 50 micron.(ii) glass shall be measured and paid for seperately(iii) cost of all fittings & fixture shall deemed to be included in unit quoted rate by the tenderer . 13 m&l for powder coated aluminium glazed window and ventilator shutters, side hung type without sash bars made of sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type c 21 100mm long (2 no.) aluminiumhandle (1 no.) per shutter etccomplete and as directed. note : (i)the minimum thickness of powder coating shall be 50 micron .(ii) shutter shall be fixed on frame of required size and shall be measured seperately (iii) glass shall be measured and paid for seperately(iv) cost of all fittings & fixture shall deemed to be included in unit quoted rate by the tenderer . 14 m&l forpowder coated aluminium sliding window shutters ( shutters to be slide insuitabletrack system ) ( two panel shutter ) fabricated out of section for outer frame having weight not less then 1.17kg/rm, sliding window shutters made of sectionsall roundhavingweight not less than 0.42 kg/rm top rail , bottom rail and verticle styles and midlle rail of shutter having weight not less then 0.368 kg/rmand including providingnecessary powder coated aluminium fittings , 5mm thick tinted ,selected qualityglass ,stainless steel wire cloth .36 mm dia steel wire and apperture 1.18 mm and shutter provided with aluminium deco grill made of 10 mm quare bras and mesh size 50 mm both ways etcfixed with standard aluminium channel to outer side and including providingpowder coated aluminium handle , cleats and glazing clip special and suitable auto lock system , rubber gasket etc complete all as specified and as directed. 15 supply only5.5 mm thick sheet glass selected qualitytinted complete all as specified and as directed. 16 s&f in repair tinted glass and glazing with beading of any size of 5.5 mm thick complete all as specified and as directed. 17 s&f butt hinges extruded aluminium alloy with galvanised mild steel hing pin anodised and fixed type c 21, 100 mm size in toilet with pvc doors etc complete all as specified and as directed. 18 s&f, plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints,supplied and fixed etc complete all as specified and as directed 19 s&f, pressed steel frames for doors(125x60) mmwith one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed etc complete all as specified and as directed. 20 s&f, pressed steel frames for doors(105x60) mmwith one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed etc complete. 21 s&f, locally fabricated plain framed paneled shutter 35 mm thick iindclass hw (any number & panels) with lock rail and panel of 9 mm b.w.p commercial ply or 12mm veneered particle board with commercial veneering on bothface, the size of rail and style as per is : 1003 (part i) kiln seasoned and chemically pressure treated etc complete all as specified and as directed 22 s&f, locally fabricated 35 mm thick iind class hw glazed & skeleton shutters open rebated and prepared to receive glass gauge etc. (without sash bars) edges of framing plain chamfered or rounded fitted with cut & mitered beads for security glass/gauge etc. size of members of shutter as specified in ssr pt i sec 8 cl 8.20 (a), divided into squares with plain chamfered rounded, mitered and rebated sash bars etc complete all as specified and as directed 23 s&f, locally fabricated 35 mm thick iind class hw partly paneled& partly gauged & skeleton shutters open rebated and prepared to receive glass/gauge etc. (without sash bars) edges of framing plain chamfered or rounded fitted with cut & mitered beads for security glass/gauge etc. size of members of shutter as specified in ssr pt i sec 8 of 8.20 (a),divided into squares with plain chamfered rounded, mitered and rebated sash bars etc complete all as specified and as directed 24 s&f, 35mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed by the engineer in charge 25 ditto all as per item no20 above but 30 mm thick windows, ventilators etc provided with stiles and rails as specified in ssr pt i sec 8clause 8.20 (b) etc complete all as specified and as directed 26 s&f plain fillets, square, rectangular or triangular in section clean sawn secured with nails or brads iind classhw sectional area exc 6 sqcm but n exc 13 sqcm etc complete all as specified and as directed 27 s&f3mm thick, sheet glass, ordinary quality and glazing withoil putty in square in exc 0.5 sq.m in each pane etc complete all as specified and as directed. 28 s&f in repair 3 mm thick sheet glass, ordinary quality and glazing with wooden beads in square n. exc 0.5 sqm in each pane or glazing with oil glass putty including hacking out old broken glass from wooden or steel frame surround complete all as specified and as directed etc complete all as specified and as directed. 29 s&f galvanized mild steel wire cloth 0.63 mm nominal dia of wire and avg width of apertare 1.40 mm fixed with tinned tacks or galvanized wire staples etc complete all as specified and as directed. 30 s&f, in repair galvanized mild steel wire cloth 0.63 mm nominal dia of wire and avg width of a pertare 1.40 mm fixed with tinned tacks or galvanized wire staples etc complete all as specified and as directed. 31 s&f, butt hinges medium weight cold rolled, mild steel and fixed 50 mm size etc complete all as specified and as directed. 32 s&f, butt hinges medium weight cold rolled, mild steel and fixed 75 mm size etc complete all as specified and as directed. 33 s&f, butt hinges medium weight cold rolled, mild steel and fixed 100 mm size etc complete all as specified and as directed. 34 s&f, aluminum handles cast type anodized 100 mm size etc complete all as specified and as directed 35 s&f, aluminum handles cast type anodized 125 mm size etc complete all as specified and as directed 36 s&f, aluminum anodized barrel tower bolts of extruded section 150 mm long etc complete all as specified and as directed 37 s&f, aluminum anodized barrel tower bolts of extruded section 200 mm long etc complete all as specified and as directed 38 s&f, aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) 300mm long etc complete all as specified and as directed 39 m&l, prepairing surfaces of wood and wood based material, steel and iron work, new or old, of any desctiption and girth not otherwise desctibed and treated with tar or coal tar black paint etc complete all as specified and as directed 40 s&f, mild steel flat iron 25x3 mm as in hold fasts etc all as specified,confirming to fe 410 0 or fe 310 0etc complete all as specified and as directed 41 m&l,treating small articles such as stop, cover, hold fasts etc back of chowkhat etc area n.exc 0.1 sqm each etc complete all as specified and as directed 42 cutting holes in brick walls built in cement mortar for inserting hold fasts and making good dismantled portion in cm 1:3 or cement conc 1:2:4 type b1 as required exc half brick but not exc full brick walletc complete all as specified and as directed 43 m&l, pcc 1:3:6 type c1 using 20mm graded stone aggregate as in coping or bed plates for filling in holes of hold fasts or in pressed steel frameincluding necessary use and waste of form work etccomplete all as specified and as directed 44 m&l, two coat synthetic enamel paint over one coat of pink primer on new wooden surface of any description not otherwise described over 10 cm width or girth etc complete all as specified and as directed 45 m&l, framed work as grills, gratings, etc with ends of bars shouldered and/ or riveted into spikes; or forged into spikes, framed guard bars; barred iron doors and similar work confirming to fe 290. gd e 165 etc complete all as specified and as directed 46 s&f, 1mm thick mild steel, plain black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc complete all as specified and as directed 47 s&f in repair steel window or ventilator fixed type with glazing bars etc complete all as specified and as directed 48 s&f, in repairs steel windows with side hung shutters including projecting type hinges with steel handles, and steel peg stay complete with glazing bars dovetailed or welded etc complete all as specified and as directed 49 s&f, in repairs steel windows with side hung shutters including projecting type hinges with steel handles, and steel peg stay complete without glazing bars dovetailed or welded etc complete all as specified and as directed 50 supply only small fittings such as bracket of any type latch and hing block, shaped doors and window stops and the like incl all necessary articles n.exc 200 cucm each, made out ofiind hwetc complete all as specified and as directed 51 m&l, two coats ofsynthetic enamel paint over one coat of red oxide primer on new steel surface of any description not otherwise described over 10 cm width or girth etc complete all as specified and as directed 52 s&f, in repair 225mm, ordinary rat tail rod patttern springs includding roller and roller plate etc complete all as specified and as directed 53 s&f, 19/20mm thick prelaminated particle board interior grade prelaminated one side with decorative choice laminations and other side balancing white lamination fixed with screws to timber frame work etc complete all as specified and as directed. 54 s&f, 12 mm thick prelaminated particle board interior grade prelaminated one side with decorative choice laminations and other side balancing white lamination fixed with screws as in pelmet boxes etc.n. exc. 15 cm width to timber frame work etccomplete all as specified and as directed. 55 m&l, for external teak wood lipping 6mm thick and 19/20mm wide fixed with nails on edges of pelmet boxes incuding wooden polishing on beading etc complete all as specified and as directed. 56 s&f hasp & staple safety type aluminium anodized with mild steel hinge pin incl bolt to hinge plate and fixed with screws 100mm size etc complete all as specified and as directed. 57 s&f, continuous (piano) hinges, mild steel bright finish electrogalvanised 20mm width of flap etc complete all as specified and as directed. 58 s&f, 40mm dia mild steel bright finished cupboard knobs fixed with screw and washer etc complete all as specified and as directed 59 s&f 18 mm thick rajshri celuka ply of one side prelaminated and other side plain white colourto make kitchen cabinet/ drawer shutters complete as per specifications and as directed by the engineer in charge. note : modular kit accessories i.e. basketts, cutlery baskets, fittings and fixture will be measured and paid separately as supply only. 60 s&f 12 mm thick rajshri celuka ply ofboth side plain white colour fixed with screws, solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per specifications and as directed by the engineer in charge. 61 s&fauto closing hinges 35 mm of 0 crank( kh 001) or8 crank (kh 002) openable at 110 degree for kitchen cabinet shutters,complete all as specified and as directed 62 s&f ball bearing runners 45 mm telescopic (kts 20) full extension load capacity 50 kgs, as directed. make kaff or equivalent in specifications 63 s&f stainless steel handles 100 mm sizefor kitchen cabinet shutters complete all as specified and as directed by engineer in – charge. 64 taking down unserviceable aluminium shutter of any description exc 1 but n.exc 2 sqm each making easing, servicable, replacing rubber beading and refixing in the same opening complete all as specified and as directed by engr in charge 65 taking down unserviceable aluminium shutter of any description n.exc 1 sqm each making easing, servicable, replacing rubber beading and refixing in the same opening complete all as specified and as directed by engr in charge 66 s&f, in repair aluminium (extruded section body) door closer hydraulic regulated designation no 3 uiversal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed etc complete all as specified and as directed 67 s&f, floor door stoper (140mm overall lengthofcover plate) aluminium alloy body and tongue anodised, with hard drawn steel spring fixed in floor etc complete all as specified and as directed 68 s&f, in repair mortice lock alumunium body, vertical type of size 100mm of 7 levers etc compete all as specified and as directed 69 taking down cement plaster on brick or stone walls etc incl racking out joints hacking for key and scrabbing down with water etc and as directed. 70 m&l rendering10mm thick in cementmortar 1:6 on fair faces of brick or concrete surface of wall, surface finishedeven smooth with out using extra cement complete all as directed . 71 m&l rendering15mm thick in cementmortar 1:4 mixed with wpc , on fair faces of brick or concrete surface of wallsurface finishedeven and smooth,without using extra cementcomplete all as directed . 72 m&l for preparing newly plastered surfaces of wall and applying two coats of oil bound distemperover a coat of primeretc complete and as directed. 73 m&l for preparing onnewly plastered surfaces of wall and applying two coats of cement based paint over a coat of cement based primer etc complete and as directed. 74 demolition of brick work or stone masonary built in cement mortar as in drain, manhole, septic tank and soak well complete all as specified and directed. 75 m&l brick work with sub class b bricks straight or curved on plan exc 6m mean radious and built in cm 1:4 complete all as specified and directed. 76 m&l for rendering 15mm thick on fair faces of wall even and smooth finish without using extra cement onconc/brick surfaces in cm 1:6, complete all as specified and as directed 77 m & l for preparation of new plastered surface of wall and applying three coats of white wash complete all as specified and directed 78 s&f in repair pvc bathroom cabinet with mirror of size 432mm x 311mm complete all as specified and as directed by the engineer in charge 79 s&f in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick ac building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 80 taking down wall panelling and similar worketc and complete all as specified and directed 81 s&f forsolid pvc wall lining consisting of 5mm thick plain colourpvc sheet inclusive of solvent cement and fixing at site of 5mm thick pvc sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to pvc frame complete all as specified and directed 82 s&f in repair false ceiling with 9 9.5 mm thick gypsum board tiles laminated with white pvc film on face side & metalized polyster film (aluminium foil) on the back side with all four edges sealed with pvc filmof size 600 x 600 mm (595 x 595 mm) fixed with clips & screws including anodised aluminium snap grid frame work for false ceiling of tee/angle of weight not less than 300 gm per rm with slot for fixing including necessary suspender of flat iron or 4 mm dia bars of required length fixed in purlin of roof not exceeding 1.20 m both ways including all accessories required for suspending ceiling work and gypsum board complete all as specified and as directed by the engineer in charge. 83 s&f in repairstainless steel curtain rod of 25 mm dia pipe quality h 304 etc complete and as directed 84 s&f brackets , fancy type suitable for 25 mm dia curtainrodcomplete and as directed 85 s&f end knob , fancy type for curtainrod 25mm diacomplete all as specified and as directed. 86 dismantling floor hearth wall tiling including cement mortar bedding but not backing removing serviceable meterial to store complete all as specified and directed. 87 m&l for 15mm thick screed bed or bedding layer in cm 1:6complete all as specified and directed. 88 m & l rendering 10mm thick in cement mortar (1:3) on fair faces of brick work or concrete surfaces as in vertical surfaces for receiving tiles complete all as specified and directed. 89 m&l for glazed ceramic coloured tiles 300x200x 6 to7mm thick for work on vertical surface such as skirting, dado, set & jointed in cement slurry and pointed in white or coloured cement to match complete all as specified and directed. 90 m&l, coloured non skid dark/light ceramic tile 7 to 8mm thick (square / rectangular)area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed 91 m&l, coloured non skid dark/light ceramic tile 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting /dado etc set and jointed in neat cement slurryand pointed in coloured cement to match complete all as specified and directed 92 m&l for vitrified ceramic tiles 10mm thick (square/rectangular) polished area of each tile notexceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. 93 m&l for vitrified ceramic tiles 10 mm thick (square / rectangular) polishedarea of each tile exceeding 0.18 sqm but not exc 0.36 sqm, in vertical surfaces such as skirting, dado etc. set and jointed in neat cement slurryand pointed in white or coloured cement to match complete all as specified and directed. 94 s&f in repair glass self (500mmx60mm) with abs brackets (450x125x6) and fixed to wall with cp brass screws complete all as specified and as directed. 95 supply and fix in repair cp corner glass shelf with bracket fixed with screws complete all as specified and as directed by engineer in charge . 96 s&f stainless steeltowel rack fixed to wall with cp brass screws complete all as specified and as directed. 97 s&f in repair brass chromium plated tubular towel rail 20mm dia ‘d’ type 60 cm long between flanges alluminium anodisedall as specified and as directed. 98 s&f in repair stainless steel kitchen plate rack overall size 900mm x 900mm make out of 0.80mm thick stainless steel sheet etc complete all as specified and as directed 99 s&f in repairs 100 mm long, aluminium handles, cast type, anodised complete all as specified and as directed 100 s&f in repairs 150 mm long, aluminium handles, cast type, anodised complete all as specified and as directed 101 s & f in repairs 200 mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed 102 s & f in repairaluminum siliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts for on bolts plate and two on staple plate and fixed 300mm long etc complete all as specified and as directed 103 s&f in repairms butt hinge 75mm ,cold rolled medium weight complete all as specified and directed. 104 s&f in repairms butt hinges, cold rolled medium weight 100mm in size complete all as specified and directed. 105 s&f in repair 250mm aluminium alloy,anodised,sliding door bolt with hasp staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing boltsand sliding bolts of extruded sections and fixed complete all as specified and directed. 106 s & f in repair 75 mm size aluminium anodised hasp and staple, including bolt to hinge plate and fixed with screws complete all as specified and as directed. 107 s&f as in replacement of dust guard vertical type venation blind of approved colour including all items for fixing the same in windows complete all as specified and directed with specifications given below : (a) (i) material – p.v ( polyester vishcoues). (ii) width – 100mm (iii) thickness – 0.55mm (iv)reflecting black – no specification for roller plate : (b)(i) material – aluminium with powder coating. (ii) weight – 330 gm/mtr (approx) (iii) height – 25mm (iv) width – 50mm 108 dismantling asbestos cement ,galvalume fiber sheet ( plan corrugated,semicorrugated, etc.) sheets in roof coverings all as specified and directed 109 m & lfor 6 mm thick asbestos cement corrugated sheet, in roofs, wall etc and fixed with ‘l’ or j hooks or cranked bolts with washers complete all as specified and directed. 110 m & lfor 6 mm thick asbestos cement corrugated sheet, in roofs, wall etc and fixed with ‘l’ or j hooks or cranked bolts with washers. but except sheet (sheet shall be obtained from dismantling)complete all as specified and directed. 111 m & lfor asbestos cement plain angular ridge for corrugated or semi corrugated sheets 6 mm thick fixed with ‘l’or j hook or cranked bolts. 112 m & lfor pre painted galvalume aluminium zinc coating gi based corrugated steel sheet 0.50mm of an colour having tensile strength of 550mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified 113 m & lfor pre painted galvalume aluminium zinc coating gi based plain steel sheet 0.50mm of an colour having tensile strength of 550mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified 114 dismantling wrought iron or mild steel work of any description not otherwise provided all as directed and as directed 115 m&l for roof trusses, trussed, purlines, crane gantries, rail and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) complete all as directed and as directed...

Meja Urja Nigam Private Limited - Uttar Pradesh

37040202 procurement of complete aru assembly and spares of the vessels , anion regeneration unit aru , aru sight glass , aru vent strainer , aru :drain down strainer , aru inlet water strainer , cru: inlet water strainer , cru:sight glass , cru :vent strainer , cru:drain down strainer , cru :bottom strainer , service vessel sight glass , service vessel:resin trap , alkali filter: bed plate strainer , alkali filter: sight glass , alkali filter:resin trap element , fume absorber for acid storage tank , fume absorber for acid measuring tank , co2 absorber for alkali storage tank , co2 absorber for alkali measuring tank => limited...

Uttar Pradesh Jal Nigam - Uttar Pradesh

36877650 tender for invitation of rates for supply of civil, electrical, sanitary, other materials and piece rated works ( labour ) 1 earth work in excavation in trenches for foundation pipes, cable etc in ordinary sol ( loam clay or sand ) inlcuding lift upto 1.5 mt. lead upto 30mt. and dressing of sides and rammings of bottom and disposal of surplus excavated earth as directed by the engineer. 2 upto 1.50 m to 3.00 m deep 3 upto 3.00 m to 4.50 m deep 4 upto 4.50 m to 6.00 m deep 5 filling of carted earth 6 laying in position cement concrete of specifiedgrade including the cost of centring and shuttering all work upto plinth level. 7 in cement concrete 1:4:8 ( 1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size ) 8 in cement concrete 1:2:4 ( 1 cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size ) 9 coarse sand ( compacted ) filling in sides of foundation & floor 10 providing and injecting chemical emulsion for pre constructional antitermite treatment and creating a chemical barrier under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete. ( plinth area of the building at ground floor only shall be measured as per i.s.6313 ( partii 1981 ) alderine emulsifiable concentrate or any other approved material such as heptrachlor or chlordane will be used. the rate of application of chemical emulsion shall be as follows : ( 1 ) treatment for masonary & foundation 5 liters per sqm. ( 2 ) back fill in immediate contact with foundation 7.5 liters / sqm ( 3 ) treatment of top surface of plinth filling 5 liters / sqm ( 4 ) treatment junction of wall and the floor 7.5 liters / sqm ( 5 ) treatment of soil along external perimeter of building 7.5 liters / sqm ( 6 ) treatment of soil under apron along external perimter 5 liters / sqm. ( as per manufacturers standard dilution ) 11 r.c.c. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 bwg binding wire and including necessary centering and shuttering etc.and also excluding supply of all materials, and including labour and tools and plants etc, required for proper completion of the works. 12 ground floor 13 first floor 14 second floor 15 as in item no. 6 above but for slabs ( using 1:1.5:3 mix concrete ) . 16 ground floor 17 first floor 18 second floor 19 as in item 6 but for thelighterbeams i.e. having spans upto 6 m. ( using 1:1.5:3 mix concrete ) 20 ground floor 21 first floor 22 second floor 23 as in item 6 abovebut inr.c.c.raft foundation and footingwithapproved stone ballast. ( using1:1.5:3mix concrete ) 24 as in item 6 above but in r.c.c. columns in 1:1.5:3 having strength not less than m 20. 25 ground floor 26 first floor 27 second floor 28 m 150 brick work in 1:6 ( one cement and six coarse sand sand of 2.25 fineness modulus ) mortar infoundation & plinth includinglabour and t & p etc & excluding supply of all materials, required for proper completion of the work. 29 m 150 brick work in 1:4 ( one cement and six coarse sand sand of 2.25 fineness modulus ) mortar infoundation & plinth includinglabour and t & p etc & excluding supply of all materials, required for proper completion of the work. 30 laying damp proof course 40mm thick with cement concrete 1:2:4 ( 1 cement : 2 coarse sand ( zone iii ) : 4 graded stone aggregate 12.5mm nominal size ) 31 applying a coat of residual petroleum bitumen of grade of vg 10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 32 same as in item no. 11 abovebutin super structure above plinth level up to floor two level ( up to two storeys ) includingnecessarycutting and moulding of brick work asrequiredand also including honeycombed brick work in thickness of wall more than 12cms. ( 1:6 cement : coarse sand ) 33 ground floor 34 first floor 35 second floor 36 same as in item no. 14 but in1:4 cement and coarse sand mortar in superstructure for wall thickness 12 cms & below brick work. 37 ground floor 38 first floor 39 second floor 40 mild steel or iron in plain work such as reinforced concrete or reinforced, brick work ( when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and excluding supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. 41 ground floor 42 first floor 43 second floor 44 15 mm cement plaster on rough side of single or half brick wall of mix : 1:3 ( 1 cement: 3 coarse sand ) 45 15 mm cement plaster in single coat on rough side of single or halfbrick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. ( 1 ) 1 cement : 6 fine sand . 46 ground floor 47 first floor 48 second floor 49 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and / or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. ( 1 ) 1 cement : 6 finesand. 50 ground floor 51 first floor 52 second floor 53 engraving lines in the plaster of outer face well vertically & horizontally to display the surface as stone facing as directed by the engineer in charge including labpur, & t & p etc. required for proper completion of the work. 54 ground floor 55 first floor 56 second floor 57 add for plaster drip course / groove in plastered surface or moulding to r.c.c. projections. 58 laying 8 to 10 mm thick ivory or light shade vitrified tiles of 600 x 600 mm size with all colours and shades, laid on 20mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) finishing with cement slurry & with pigment grouting & polishing complete including supply of all labour, t & p etc. excluding the cost of materials required for proper completion the work. 59 ground floor 60 first floor 61 second floor 62 laying 8 to 10 mm thick ivory or light shade vitrified tiles of 600 x 600 mm size with all colours and shades, laid on 20mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) finishing with cement slurry & with pigment grouting & polishing complete including supply of all labour, t & p etc. excluding the cost of materials required for proper completion the work. 63 ground floor 64 first floor 65 second floor 66 kota stone slab flooring over 20 mm ( average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand ) : 25 mm thick 67 ground floor 68 first floor 69 second floor 70 kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm ( average ) thick cement mortar 1:3 ( 1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 71 ground floor 72 first floor 73 second floor 74 fixing of 6 mm thick approved china white / coloured glazed tiles in flooring or dado laid with 1:3 cement and approved coarse sand mortar finished and jointed with white cement slurry and pigment and polishing complete includinglabour and tool sand plants & excluding supply of all materials, etc. required for proper completion of the work. 75 ground floor 76 first floor 77 second floor 78 25 mm thick cement concrete flooring 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 12.5mm nominal size and below ) by laid over base concrete finished with floating coat of neat cement ( base concrete to be paid separately ) including fixing of glass strips. ( excluding cost of glass strips ) 79 supply of flush doors commercial qualityconforming to i.s.2202 part i ( 1983 ) including fixing of wooden cleats and stoppers 80 35 mm thick 81 ( a ) single leaf 82 ( b ) double leaf 83 32 mm thick 84 ( a ) single leaf 85 extra for providing and fixing flush doors with decorative veneering instead of non decorative isi marked flush door shutters conforming to is: 2202 ( part i ) 86 fixing of flush / pvc doors including fixing of wooden / pvc cleats and stoppers and includingfixing and adjustment of hinges, bolts, locks, handle, springs. fittings to be supplied departmentally. 87 supply of factory made panel pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. m.s. frame shall have a coat of steel primers of approved make and manufacture. m.s. frame covered with 5 mm thick heat moulded pvc ‘c’ channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide pvc sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide pvc sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. top, bottom and lock rails shall be provided both side of the panel. 10 mm ( 5 mm x 2 ) thick, 20 mm wide cross pvc sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side pvc sheet to be fitted in the m.s. frame welded / sealed to the styles & rails with 7 mm ( 5 mm+2 mm ) thick x 15 mm wide pvc sheet beading on inner side, and joined together with solvent cement adhesive. an additional 5 mm thick pvc strip of 20 mm width is to be stuck on the interior side of the ‘c’ channel using pvc solvent adhesive etc. complete as per direction of engineer in charge, manufacturer’s specification & drawing. 30 mm thick plain pvc door shutters 88 mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods, gratings etc. ( when not included in an over all rates ) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. 89 m.s. hold fast for doors and windows 90 m.s. grill 91 z section winodws ( openable ) 92 m.s. angle door chaukhat 40*40*5 93 fixing of door, windows / ventilators chaukhats in position. 94 ( a ) door chaukhats 95 ( b ) window chaukhats 96 ( c ) ventilator chaukhats 97 distempering ( two coat ) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as berger, j&n, shalimar, asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. ( inside walls ) 98 ground floor 99 first floor 100 second floor 101 finishing walls with two coat of acrylic smooth exterior paint of best quality including supply of all materials labour and tool sand plants etc. required for proper completion of the work. 102 ground floor 103 first floor 104 second floor 105 finishing wall with water proof cement paint of approved make and quality on new wood with two coat to give an even shade including supply of all materials, labour, tools and plant etc. required for proper completion of the work. ( two coat ) 106 wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : two or more coats on new work supply of all materials, labour, tools and plant etc. required for proper completion of the work. ( two coat ) 107 distempering ( two coat ) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as berger, j&n, shalimar, asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth excludingcost of all materials. ( ceiling ) 108 providing & applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 109 supply of 150 mm bright finished floor stainless steel door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete. 110 supply of stainless steel sliding door bolts isi marked anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade with nuts and screws etc complete. ( a ) 250mm x 16mm . 111 supply of stainless steel towerbolts ( barrel type ) with necessary screws etc. complete 112 ( a ) 300mm x 10mm 113 ( b ) 250 mm x 10mm 114 supply of bright / matt finished stainless steel handles of approved quality & make with necessary screws etc all complete. ( a ) 125 mm 115 providing and laying cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a ) applying a slurry coat of neat cement using 2.75 kg / sqm of cement admixed with water proofing compound conforming to is. 2645 and approved by engineer in charge over the rcc slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b ) laying brick bats with mortar using broken bricks / brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 ( 1 cement : 5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge over 20 mm thick layer of cement mortar of mix 1:5 ( 1 cement :5 coarse sand ) admixed with water proofing compound conforming tois : 2645 and approved by engineer in charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c ) after two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge. d ) finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 ( 1 cement :4 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e ) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. all above operations to be done in order and as directed and specified by the engineer in charge : with average thickness of 120 mm and minimum thickness at khurra as 65 mm. 116 painting or vanishing two coat on iron work in small areas or new wood work with one coat of ready mixed priming paint and one coat of approved superior ready mixed paint of clear synthetic varnish including supply of all materials, labour, t & p etc. required for proper completion the work. paint to be used should confirm to the i.s.i. no. 103 1950. 117 same as item above but on new wood surface. 118 fixing panes of glass with equal or equivalent i.s.i. marked quality putty, brads and springs including supply of all materials, labour etc. complete. 3.80 to 4.70 mm thick 119 chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing & excluding supply of all materials complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement :4 coarse sand ) : light shade pigment using white cement. 120 filling of light cinder filling under floor of toilets & other sunken roofs. 121 labour charges for wiring points for light with 1.5 sqmm.frlsh pvc insulated single core copper condutor cable in pvc conduit pipe partly concealed in wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sqmm.frlsh pvc insulated multistrand copper conductor cable as earth continuity wire and piano type switch etc. complete in all respects. 122 same as item no. ( 1 ) but for two way light points. 123 same as item no. ( 1 ) but for fanandlight duty exhaust fan. 124 same as item no. ( 1 ) but for5amp plug point with piano type switch and socket etc. 125 addition when modular type switches etc are used in place of piono type switches etc. in various wiring points. 126 addition for light / fan points with modular type switchin place of piono type switch. 127 addition for plugpointswith modular type switchin place of piono type switch. 128 addition for exhaust fanpointswith modular type switchin place of piono type switch. 129 wiring of submains with 2 nos. 2.5 sq.mm & with 1 no. earth wire of 1.5 sq.mm fr pvc insulated 1100 v grade single core multistrand copper conductor cable in 20 mm dia heavy duty ( 2mm thick ) pvc conduit complete, including supply of all material, labourand t&p etc. required for proper completion of the work as directed by engineer i / c. 130 wiring of submain 2 number 4 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 20mm dia pvc conduit partly concealed in wall and partly laid in slab along with one number 2.5 sqmm frlsh pvc insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects. 131 wiring of submain 2 number 6 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 20mm dia pvc conduit partly concealed in wall and partly laid in slab along with one number 4 sqmm frlsh pvc insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects. 132 wiring of submain 4 number 10 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 32mm dia pvc conduitalong with two numbers 6 sqmm frlsh pvc insulated multistranded copper conductorcable as earth contunity wire etc. complete in all respects. 133 wiring of submain 4 number 16 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 40mm dia pvc conduitalong with two numbers 10 sqmm frlsh pvc insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects. 134 wiring of submain 4 number 25 sqmm . frlsh pvc insulated 1100 v grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 50mm dia pvc conduitalong with two numbers 16 sqmm frlsh pvc insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects. 135 fixing and concealing of20mm dia.2mm thick pvc conduit pipe with isi mark embossed and with pvc acessories confirming to is no. 3419 for drawing wires duly sealed at joints with original resin / adhesive to make the complete piping rigid, plastering with cement sand mortar finished to level with matching colour including cost of material labour and t & p etc required for proper completion of work ( fortelephone ) 136 erection and testing of ceiling fan and regulator for room height upto 3.5mts. including supply of 3mm thick g.i. pipe 19mm dia duly painted, complete in all respects. 137 erection and testing exhaust fan on the exhisting hole with suitable size of rag bolts nuts and washers etc. complete in all respects. 138 fixing of hexagonal / round g.p. fan box of approved make made up of 1.0mm thick isi marked g.p. sheet spot weeldeed four to eight holes of 25.4 mm for pipe entry of the box. holes should be semi shuttered type with 0.5mm g.p. sheet made upper & lower cover duly screewed fitted with 300mm round zink coted m.s bar x 12mm & brand name should be embossed.fixing with wiring conduit laid in the r.c.c roof before concreting alongwith supply of all material, labour, t&p etc. required for proper completion of the work. 139 supply of ceiling fan with fan motor of a.c permanent insulation, capacitor rating conforming bee 5 star rating and is:374 / 79 and also comply with is: 1709 / 1984 with latest amendment. the rated voltage 220 / 240 volts, 50hz, 1 ph ac the fan assemble should consists of down road blades, shackle canopies etc and with double ball bearing system. bee 5 star rated 1200mm sweep 140 fixingofelectronic fan regulator ( modular ) 120 280 v. isimarked, on the existing switch board including making connetion, required material, labour t / p etc for proper completion of work to the satisfaction of engineer in charge of work. 141 fixing of led tube light with metal heavy dutybox type batten light fitting 2 x 22 watt suitable for up to 2 x 22 watt led polycarbonate tube light complete including tube etc suitable for both surface & surface complete in all respects. ( cat: aaa ) 142 fixing of led tube light with metal heavy dutybox type batten light fitting 1 x 22 watt suitable for up to 1 x 22 watt led polycarbonate tube light complete including tube etc suitable for both surface & surface complete in all respects. ( cat: aaa ) 143 fixing of recess / surface mounting round 10 to 15 watt, cut out min 125mm, height min 40mm, led down lighter having powder coated die cast aluminium housing with heat sink, diffuser / reflector and driver set, suitable for 24hr continuous operation, complete in all respect. ( cat: aaa ) 144 fixing of single led light wall bracket on matching m.d.f.e.g board base etc. complete in all respect. ( cat: aaa ) 145 fixing of water tight oblong 10 watt led bulhead luminaire with driverr set confirming to ip 65 and above protection complete in all respect. ( cat: aaa ) 146 fixing of surface / flush mounting distribution boards with additional metal door withot mcb complete in all respects. ( cat a ) 147 4 way tpn 148 6 way tpn 149 8 way tpn 150 fixing of 6amp to 32 amp ( 10 ka ) sp mcb in existing mcb, db complete with connections as required. ( cat: a ) 151 fixing and making connection of following mcbs complete in all respects as per direction and satisfaction of engineer in charge. ( cat: a ) 152 40 amp. fp mcb ( cat: a ) 153 63 amp. fp mcb ( cat: a ) 154 fixing of surface / flush mounting v tpn distribution boards with additional metal door withot mcb complete in all respects. ( cat a ) 4 way v tpn 155 fixing and making connection of following mccbs complete in all respects as per direction and satisfaction of engineer in charge. ( cat: a ) 156 100 amp. fp mccb ( cat: a ) 157 125 amp. fp mccb ( cat: a ) 158 160 amp. fp mccb ( cat: a ) 159 fixing and making connection of following mcbs complete in all respects as per direction and satisfaction of engineer in charge. ( cat: a ) 160 40 amp. tp mcb ( cat: a ) 161 63 amp. tp mcb ( cat: a ) 162 fixing of power plug with 15a / 250 v flush type switch and 5 pin 15 a / 250v flush type universal socket in suitable m.s. box of 175mmx100x50mm size with phenolic laminated bakellite sheet cover 3mm thick fixed with brass machine screws and cup washer. 163 fixing of power plug with 20a / 250 v flush type switch and 5 pin 20 a / 250v flush type universal socket in suitable m.s. box including supply of all material, labor t&p etc. required for proper completion of work. 164 fixing of single pole mcbs blanking plate complete in all respects. ( cat: a ) 165 fixing and making connection of following mccbs complete in all respects as per direction and satisfaction of engineer in charge. 63 amp. fp mccb 166 supply and burying of 600mm x 600 mmx6mm g.i. plate, vertically for earthing with its top atleast 3 mts. below ground level complete with 20mm g.i.pipe and funnel for watering and two earthing leads of no.8to10swg g.i.wire in 15mm dia g.i. pipe upto switch board ( from apron to switch board the cost of g.i. pipe and g.i. wire will be extra ) 30cm. square c.i. frame with hinged cover, masonary housing, alternate layers / of charcoal / coke and salt at least 150mm thick alround etc. complete in 167 laying of 25mmx3mm g.i. strip for earthing purpose as required complete in all respects. 168 fixing of two number 8 swg g.i. wire in 15mm dia gi pipe for earthing purpose as required complete in all respects. 169 laying of aluminium conducter, pvc insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the 170 95 sqmm3.5 core 171 70 sqmm3.5 core 172 50 sqmm3.5 core 173 35 sqmm3.5 core 174 25 sqmm3.5 core 175 10 sqmm4 core 176 fixing of brass nickle plated compression gland for pvc insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respects. the armouring of the cable shall be properly connected with the earth as per dire 177 95 sqmm3.5 core 178 70 sqmm3.5 core 179 50 sqmm3.5 core 180 35 sqmm3.5 core 181 25 sqmm3.5 core 182 10 sqmm4 core 183 fixing of palm / pin type copper tin plated cables sockets ( lugs ) to the cable leads, insuslating with tape and making of connections etc. complete in all respects as per direction of engineer incharge. 184 95 sqmm 185 70 sqmm 186 50 sqmm 187 35 sqmm 188 25 sqmm 189 16 sqmm 190 10 sqmm 191 6 sqmm 192 fixing ofmodular boxes, base & cover plate 193 fixing of following size / modules, gi box along with modular base& cover plate for modular switches in recess etc as required. 1 or 2 module ( 75mm x 75 mm ) 194 fixing ofmodular type switch / socket : 195 fixing of following modular switch / socket on theexisting modular plate & switch box including connections but excluding modular plate etc as required. 196 telephone socket outlet 197 tv antenna socket outlet 198 bell push 199 fixing of call bell / buzzer suitable single phase, 230 v etc as required. 200 laying oftelephone wire following pair 0.5 sqmm fr pvc insulated annealed copper conductor, unarmoured telephone cable in the existing surface / recessed steel / pvc conduit as required. 2 pair 201 drawing of co axial tv cable rg 6 grade, 0.7 mm solid copper conductor pe insulated, shielded with fine tinned copper braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required. 202 drawing telephone wire following pair 0.5 sqmm fr pvc insulated annealed copper conductor, unarmoured telephone cable in the existing surface / recessed steel / pvc conduit as required. 203 20 pair 204 10 pair 205 fixing of 10 pair junction boxes for floors and building with krone connectors , with connection and punching of same 206 fixing of 20 pair junction boxes for floors and building with krone connectors , with connection and punching of same 207 fixing of 50 pair junction boxes for floors and building with krone connectors , with connection and punching of same 208 laying unplastisized rigid pvc pipe conforming to is:13592 type a including jointing , cuttingand making good the walls & floors as per requirement. 150mm 209 supply of ac 230 / 250 volts, 50 hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required 300mm sweep. 210 fixing of energy meter and other accessories including connections etc. complete as required 3 phase meter 211 erection of ac 230 / 250 volts, 50 hz wall fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required450mm sweep. 212 supply of ac 230 / 250 volts, 50 hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required450mm sweep. ( at labs ) 213 fixing of wired decorative mirror light on suiatable for 9 watt led with lamp complete in all respect. 214 fixing of factory wired integral led flood light luminaires with die cast aluminium housing built with driver set suitable for 40 to 50 watt conforming to ip 65 / 66 protection complete in all respect. ( cat aaa ) 215 providing and laying water proofing treatment in sunken portion of wcs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a ) first layer of slurry of cement @ 0.488 kg / sqm mixed with water proofing cement compound @ 0.253 kg / sqm. this layer will be allowed to air cure for 4 hours. b ) second layer of slurry of cement@ 0.242 kg / sqm mixed with water proofing cement compound @ 0.126 kg / sqm.this layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. the rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. 216 fixing of stainless steel ( grade 304 ) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, i / c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, excluding the cost of materials on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer in charge. 217 providing and fixing of expansion joint system related with floor location as per drawings and direction of engineer in charge. the joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per astm b221 02. the system shall be such that it provides floor to floor / floor to wall expansion control system for various vertical localtion in load application areas thatccommodates multi directional seismic movement without stress to its components. system shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. the cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre engineered self centering arrangement that freely rotates / moves in all directions.the self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. provision of moisture barrier membrane in the joint system to have watertight joint is mandatory requirement all as per the manufactures design and as approved by engineer in charge. ( material shall confirm to astm 6063 ) floor joint of 100 mm gap 218 providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of engineer in charge. the joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper astm b221 02. the system shall be such that it provides watertight roof to roof / roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. system shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. the cover plate shall be designed of width and thickness required to satisfy movement 219 and loading requirements and secured to base members by utilizing manufacturer’s pre engineered self centering arrangement that freely rotates / moves in all directions. the self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including verticalisplacement. the joint system shall resists damage or deterioration from the impact of falling ice, exposure to uv, airborne contaminants and occasional foot traffic from maintenance personnel. provision of moisture barrier membrane in the joint system to have water tight joint is mandatory requirement. ( material shall confirm to astm 6063. ) roof joint of 100 mm gap 220 providing and fixing of expansion joint systemelated with wall joint ( internal / external ) location as per drawings and direction of engineer in charge. the joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per astm b221 02. the material shall be such that it provides an expansion joints system suitable for vertical wall to wall / wall to corner application, both new and existing construction in office buildings & complexes with no slipping down tendency amongst the components of the joint system. the joint system shall utilize light weight aluminum profiles exhibiting minimalexposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. ( material shall confirm to astm 6063 ) .wall joint of 100 mm gap 221 fixing in position stainless steel grade 304 plate 1.0 mm thick as per design for expansion joints. 200 mm wide. 222 granite stone slab 18 mm thick mirror polished quarter rounded with anti skid lines in treads of staircase full length flooring over 20 mm ( average ) thick base laid over and jointed with cement slurry mixed with pigment to match the shade of including rubbing & polishing complete with base of cement mottar 1:4 ( 1 cement : 4 coarse snad ) etc. complete excluding the cost of materials. 223 ground floor 224 first floor 225 second floor 226 fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of t iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, ocking arrangement, stoppers, handles, including applying a priming coat of approved steel primer & excluding the cost of materials. 227 fixing rolling shutters of approved make of 80 × 125 mm ( 3 × 18 gauge ) cold rolled ml lath inter lockedthrough their eintire length and joined together at the end by locks and mountedon specially designed pipe shaft with brackets and wall bearing & excluding the cost of materials. 228 40mm thick cement concrete flooring 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size and below ) by laid over base concrete finished with floating coat of neat cement ( base concrete to be paid separately ) including fixing of glass strips. ( excluding cost of glass strips ) 229 fixing glass strips in joints of floors and skirting or dado add the item of laying floors flush with floor level including supply of all materials, labour, t & p etc. required for proper completion the work. ( a ) 37 mm wide and 3.15 mm thick 230 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) and top layer 12 mm thick cement hardener consisting of mix 1:2 ( 1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size ) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturers specifications.but excluding the cost of materials etc. complete. 231 supply of 80mm thick rubber moulded cement concrete interlocking pavers block. the compressive strength of concrete pavers blocks shall not be less than 30mpa & 4.5kg / no. 232 providing and laying of 80mm thick rubber moulded cement concrete interlocking pavers block. the compressive strength of concrete pavers blocks shall not be less than 30mpa & 4.5kg / no. 233 fixing of angle iron frame 40x40x6 mm in position. 234 fencing with r.c.c. post placed at required distance, embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side only, provided with horizontal lines and two diagonals of barbed wire weighing 9.38 kg per 100 metres ( minimum ) , between the two posts fitted and fixed with g.i. staples on wooden plugs or g.i. binding wire tied to 6 mm bar nibs fixed while casting the post ( cost of r.c.c. posts, struts, g.i. barbed wire, earth work and concrete to be paid for separately ) 235 mild steel or iron work in heavy sizes such as trusses built up gates, door frames, record racks, roof work gates etc. wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. 236 providing and fixing fly proof galvanized m.s. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. with 2nd class teak wood beading 62x19 mm. 237 providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 35 mm thick shutters with isi marked m.s. pressed butt hinges bright finished of required size 238 providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. extra for providing and fixing flush doors with decorative veneering instead of non decorative isi marked flush door shutters conforming to is: 2202 ( part i ) on one side only 239 p / f curtain rods of 1.25mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with c.p. brass screws and wooden plugs etc. wherever necessary complete ( a ) 25 mm dia. 240 fixing of g.i. pipe ( 80 mm dia ) as per design & drawing as per drection of eic 241 fabrication of angle iron door chaukhat of 40*40*6 mm 242 supply of concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m ) , having 50 nos rounds per 6 metrelength, upto 3 m height of wall with existing angle iron ‘y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal r.b.t. reinforced barbed wire, stud tied with g.i. staples and g.i. clips to retain horizontal, including necessary bolts or g.i. barbed wire tied to angle iron, all complete as per direction of engineer in charge, with reinforced barbed tape ( r.b.t. ) / spring core ( 2.5mm thick ) wire of high tensile strength of 165 kg / sq.mm with tape ( 0.52 mm thick ) and weight 43.478 gm / metre. 243 fixing of concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m ) , having 50 nos rounds per 6 metrelength, upto 3 m height of wall with existing angle iron ‘y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal r.b.t. reinforced barbed wire, stud tied with g.i. staples and g.i. clips to retain horizontal, including necessary bolts or g.i. barbed wire tied to angle iron, all complete as per direction of engineer in charge, with reinforced barbed tape ( r.b.t. ) / spring core ( 2.5mm thick ) wire of high tensile strength of 165 kg / sq.mm with tape ( 0.52 mm thick ) and weight 43.478 gm / metre ( cost of materialsshall be paid separately ) 244 supply of m.s. foot rest as per standard design with 20x20mm sq bars. 245 fixing of m.s. foot rest including fixing with 20x20x10 cm. cement concrete block 1:3:6 ( 1 cement : 3 coarse sand : 6 gradded aggregate of nominal size 20mm ) as per standard design with 20x20mm sq bars. 246 supply ofc.i. tee at the inlet and outlet of septic tank. 247 fixing c.i. tee at the inlet and outlet of septic tank. 248 supply of 75mm dia vent pipes. 249 fixing of 75mm dia vent pipes. 250 supply of 75mm dia cast iron terminal guard. 251 fixing of 75mm dia cast iron terminal guard. 252 supply ofprecast rcc manhole cover and frame of required shape and approved quality. 253 m.d. 10 circular shape 500mm internal diameter 254 m.d. 2.5 circular shape 450mm internal diameter 255 fixing in position precast rcc manhole cover and frame of required shape and approved quality. 256 m.d. 10 circular shape 500mm internal diameter 257 m.d. 2.5 circular shape 450mm internal diameter 258 excavating trenches in all kinds ofsoil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. 259 up to 1.50 m depth 260 pipes 80 mm to 300 mmdiameter 261 1.50 m to 3.00 m depth 262 pipes 80 mm to 300 mmdiameter 263 opentimbering in trenches including shuttering and shoring complete. ( measurement to be taken of the face area timbered ) 264 depth not exceeding 1.5 meter 265 depth 1.5 to3.00meter 266 supply of non pressurenp 2 class ( light duty ) rcc pipe with collars etc. complete. 267 150 mm.dia. rccpipes 268 250 mm.dia. rccpipes 269 100 mm dia rcc pipes 270 laying of nonpressurenp 2 class ( light duty ) rcc pipe with collars jointed withstiffmixtureofcement mortar in the proportion of 1:2 ( 1cement : 2 finesand ) includingtestingof joints etc. complete. 271 150 mm.dia. rccpipes 272 250 mm.dia. rccpipes 273 100 mm dia rcc pipes 274 laying cement concrete 1:5:10 ( 1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size ) upto the haunches of pipes including bed concrete as per standard design 275 150 mm.dia. rccpipes 276 250 mm.dia. rccpipes 277 100 mm dia rcc pipes 278 constructing brick masonry manhole in cement mortar 1:4 ( 1 cement :4 coarse sand ) rcc top slab with 1:2:4 mix ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size ) , foundation concrete 1:4:8 mix ( 1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size ) inside plastering 12mm thick with cement mortar 1:3 ( 1 cement :3 coarse sand ) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size ) finished with a floating coat of neat cement complete as per standard design. 279 inside size 90x80cms and 45cms deep including ci cover with frame ( light duty ) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg ( weight of cover 23 kg and weight of frame 15kg ) . 280 extra for depth for manholes: 281 inside size 90x120cms and 90cms deep including ci cover with frame ( medium duty ) 455x610mm internal diamensions total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58kg ) . 282 extra for depth for manholes: 283 supply of orange colour safety footrests of minimum 6 mm thick plastic encapsulated as per is:10910 on 12 mm dia steel bar conforming to is:1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm thread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing. 284 fixing of orange colour safety footrests of minimum 6 mm thick plastic encapsulated as per is:10910 on 12 mm dia steel bar conforming to is:1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm thread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size ) complete as per design. 285 supply of double flanged ( screwed / welded ) centrifugally ( spun ) ductile iron pipes of class k 9 conforming to is 8329 100mm dia ductile iron double flanged 286 fixing & laying double flanged ( screwed / welded ) centrifugally ( spun ) ductile iron pipes of class k 9 conforming to is 8329 100mm dia ductile iron double flanged 287 supply of ci specials such as bends, reducers, collars etc. including cartage, loading, unloading, taxes, excise etc. complete. 288 fixing of ci specials such as bends, reducers, collars etc. including cartage, loading, unloading, taxes, excise etc. complete. 289 supply of push on joints to centrifugally ( spun ) cast iron pipes or ductile iron pipes including testing of joints and including the cost of rubber gasket : 100mm dia pipes 290 fixing of push on joints to centrifugally ( spun ) cast iron pipes or ductile iron pipes including testing of joints and including the cost of rubber gasket : 100mm dia pipes 291 supply ofc.i. sluice valves ( with cap ) complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) : 100mm diameter 292 fixing of c.i. sluice valves ( with cap ) complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) : 100mm diameter 293 supply of c.i. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete ( the tail pieces, tapers etc. if required will be paid separately. a ) 50mm dia 294 fixing of c.i. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete ( the tail pieces, tapers etc. if required will be paidsaperately 50mm dia 295 supply of g.i. pipes ( medium ) complete with g.i. fittings 296 80mm nominal bore. 297 65mm nominal bore. 298 50mm nominal bore. 299 40mm nominal bore. 300 32mm nominal bore. 301 25mm nominal bore. 302 20mm nominal bore. 303 15mm nominal bore. 304 laying, jointing, testing & commisioning ofg.i. pipes complete with g.i. fittings includingtenching and refilling etc. ( external work ) 305 80mm nominal bore. 306 65mm nominal bore. 307 50mm nominal bore. 308 40mm nominal bore. 309 32mm nominal bore. 310 25mm nominal bore. 311 20mm nominal bore. 312 15mm nominal bore. 313 supplying of specials for pressure pipe. 314 fixing of specials for pressure pipe. 315 supply ofgate valve ( with cap complete with bolts, nuts, rubber insertion etc. 316 80mm nominal bore. 317 65mm nominal bore. 318 50mm nominal bore. 319 40mm nominal bore. 320 32mm nominal bore. 321 25mm nominal bore. 322 fixing of gate valve ( with cap complete with bolts, nuts, rubber insertion etc. 323 80mm nominal bore. 324 65mm nominal bore. 325 50mm nominal bore. 326 40mm nominal bore. 327 32mm nominal bore. 328 25mm nominal bore. 329 constructing masonry chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 ( 1 cement : 4 coarse sand ) for sluice valve, with c.i. surface box 100mm, top diameter, 160 mm bottom diameter and 180mm deep ( inside ) with chained lid and rcc top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i / c necessary excavation, foundation concrete 1:5:10 ( 1 cement :5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design : with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 330 constructing brick masonry chamber 600 x 600x750mm insidewithf.p.s. brickwork in cement mortar 1:4 ( 1 cement : 4 coarse sand ) for sluice valve / air valve, with c. i. surface box 100 mmtop diameter, 160 mm bottom diameter and 180mm deep ( inside ) with chained lid and rcc top slabwith 1 : 2 : 4 mix ( 1 cement : 2 coarsesand : 4 gradestone aggregate 20 mm nominal size ) ; necessary excavation, foundationconcrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size ) and inside plasteringwithcement mortar 1 : 3 ( 1 cement : 3 coarsesand ) 12mmthick finished with a floatingcoatofneat cementcomplete as per standarddesign 331 supply offire brigade inlet with 63 mm dia instantaneous inlet complete with all necessary fittings and ms enclosure with glass door made of 18 / 16 swg sheet. 4 way 332 fixing, installation, testing & commissioning offire brigade inlet with 63 mm dia instantaneous inlet complete with all necessary fittings and ms enclosure with glass door made of 18 / 16 swg sheet. 4 way 333 supply of sluice valve complete with flanges, gasket, nut bolts 150 mm 334 fixing, installation, testing & commissioning of sluice valve complete with flanges, gasket, nut bolts 150 mm 335 supply of nrv complete with flanges, gasket and nut bolts. 150 mm 336 fixing, installation, testing & commissioning of nrv complete with flanges, gasket and nut bolts. 150 mm 337 supply of ms pipes conforming to is:1239 ( medium b class ) including all fittings like anchor fasteners, brick masonry supports, couplings, bends, elbows, tees and flanges etc. welded or screwed joints as required ( for riser ) 338 150 mm dia 339 100mm dia 340 fixing of ms pipes conforming to is:1239 ( medium b class ) including all fittings like anchor fasteners, brick masonry supports, couplings, bends, elbows, tees and flanges etc. welded or screwed joints as required, cutting holes and chases in brick or rcc walls and making good complete. ( for riser ) 341 150 mm dia 342 100mm dia 343 supply of manual swing type first aid fire hose reel conforming to is: 444 complete with all other necessary fixing accessories. 344 fixing, installation, testing and commissioning of manual swing type first aid fire hose reel conforming to is: 444 complete with all other necessary fixing accessories. 345 supply of fire man axe. 346 fixing of fire man axe. 347 supply of singal headed hydrant landing valve comprising of 80 mm dia flanged bend 63 mm dia, with cap and chain conforming to is:5290 ( make : newage / minimax / safex / firex ) 348 fixing, installation, testing & commissioning of singal headed hydrant landing valve comprising of 80 mm dia flanged bend 63 mm dia, with cap and chain conforming to is:5290 ( make : newage / minimax / safex / firex ) 349 supply of rrl hose pipe 63 mm dia × 15 mtr. long with gm coupling conforming to is : 636 ( make newage / jayshree / crc ) 350 fixing, installation, testing & commissioning of rrl hose pipe 63 mm dia × 15 mtr. long with gm coupling conforming to is : 636 ( make newage / jayshree / crc ) 351 supply of short branch pipe as per is:903 ( make : newage / safex / firex ) 352 fixing, installation, testing & commissioning of short branch pipe as per is:903 ( make : newage / safex / firex ) 353 supply of butterfly valve complete with flanges, gasket, nut bolts 100 mm 354 fixing, installation, testing & commissioning of butterfly valve complete with flanges, gasket, nut bolts 100 mm 355 supply of hose cabinet box of 18 swg m.s.sheet with glass to accommodate hose reel drum with ruber pipe with nozzle. 2 nos. rrl hose and 1 no. branch pipe with nozzle 356 fixing, installation, testing & commissioning of hose cabinet box of 18 swg m.s.sheet with glass to accommodate hose reel drum with ruber pipe with nozzle. 2 nos. rrl hose and 1 no. branch pipe with nozzle 357 supply of air cushion tank ( 2000x1000 ) mm. 358 fixing, installation, testing & commissioning of air cushion tank ( 2000x1000 ) mm. 359 supply of air release valve. 360 fixing, installation, testing & commissioning of air release valve. 361 supply of nrv complete with flanges, gasket and nut bolts. 100 mm 362 fixing, installation, testing & commissioning of nrv complete with flanges, gasket and nut bolts. 363 supply of pressure gauge with gauge cock 364 fixing, installation, testing & commissioning of pressure gauge with gauge cock 365 supply of electrical motor driven fire pump suitable for automatic operation consisting of following : ( terrace pump ) ( make : kirloskar / mather+platt ) ( a ) horozontally mounted, split casing, centrifugal fire pump complete for delivery of under mentioned discharge against desired mentioned head so as to ensure a minimum pressure of 30 meter at the highest and farthest outlet at the specified flow cmplete with necessary strainers, pressure gauge including bypass arrangement for periodic testing of the working of the pumpset with required length and size of medium class gi pipe and control valves for proper completion of work.the pump shall be capable of giving 150% of rated discharge at head not less than 65% of rated head.the pump shall be provided with mechanical seals. the impeller shall be enclosed type and accurately blanced dynamically.the pump casing shall be of cast iron, impeller shall be of bronze and shaft shall be of stainless steel. ( b ) squirrel cage, tefc induction motor suitable for 415 v, 3 phase having ip 55 protection and class b insulation for the above pump and flexible coupling with the pump.the motor shall b rated for continuous duty and shall have hp rating necessary to drive th pump at 150% of its rated discharge at 65% of rated head. © common bed plate of fabricated mild steel channel or cast iron type. ( d ) suitable cement concrete pump foundation and vibration clamping arrangement as required with foundation bolts, anti vibration pads, washers etc. ( e ) pressure switch for automatic operation of motor including necessary wiring upto control panel. ( f ) electrical control panel with starter, 3 pole motor protection category current limiting type mccb, indicating light, ammeter, voltmeter, selector switches, cts protective fuses, single phasing protection, dry suction cut off etc as requrd as per standard details.discharge :450 liter per minute head : 35 meter 366 installation, testing and commisioning of electrical motor driven fire pump suitable for automatic operation consisting of following : ( terrace pump ) ( make : kirloskar / mather+platt ) ( a ) horozontally mounted, split casing, centrifugal fire pump complete for delivery of under mentioned discharge against desired mentioned head so as to ensure a minimum pressure of 30 meter at the highest and farthest outlet at the specified flow cmplete with necessary strainers, pressure gauge including bypass arrangement for periodic testing of the working of the pumpset with required length and size of medium class gi pipe and control valves for proper completion of work.the pump shall be capable of giving 150% of rated discharge at head not less than 65% of rated head.the pump shall be provided with mechanical seals. the impeller shall be enclosed type and accurately blanced dynamically.the pump casing shall be of cast iron, impeller shall be of bronze and shaft shall be of stainless steel. ( b ) squirrel cage, tefc induction motor suitable for 415 v, 3 phase having ip 55 protection and class b insulation for the above pump and flexible coupling with the pump.the motor shall b rated for continuous duty and shall have hp rating necessary to drive th pump at 150% of its rated discharge at 65% of rated head. © common bed plate of fabricated mild steel channel or cast iron type. ( d ) suitable cement concrete pump foundation and vibration clamping arrangement as required with foundation bolts, anti vibration pads, washers etc. ( e ) pressure switch for automatic operation of motor including necessary wiring upto control panel. ( f ) electrical control panel with starter, 3 pole motor protection category current limiting type mccb, indicating light, ammeter, voltmeter, selector switches, cts protective fuses, single phasing protection, dry suction cut off etc as requrd as per standard details.discharge :450 liter per minute head : 35 meter 367 ( a ) horozontally mounted, split casing, centrifugal fire pump complete for delivery of under mentioned discharge against desired mentioned head so as to ensure a minimum pressure of 30 meter at the highest and farthest outlet at the specified flow cmplete with necessary strainers, pressure gauge including bypass arrangement for periodic testing of the working of the pumpset with required length and size of medium class gi pipe and control valves for proper completion of work.the pump shall be capable of giving 150% of rated discharge at head not less than 65% of rated head.the pump shall be provided with mechanical seals. the impeller shall be enclosed type and accurately blanced dynamically.the pump casing shall be of cast iron, impeller shall be of bronze and shaft shall be of stainless steel. 368 fixing & placing on terrace ( at all floor levels ) polyethylene water storage tank isi : 12701 marked indicating the bis license no. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fitting and base support for tank. [ sintex, electroplast, star, lotus or equivalent having valid isi license ] . 369 supply of halon free portable fire extinguishers as described below: 370 4.5 kg carbon dioxide extinguisher, is marked, with high pressure discharge tube, horn, control valve, cce approved cylinder 371 6 kg mono ammonium phosphate ( abc ) type cartridge operated extinguishers 372 9 kg mono ammonium phosphate ( abc ) type cartridge operated extinguishers 373 providing, fixing, testing and commissioning of 50 litres ( trolley mounted ) mechanical foam type fire extinguisher. in hp mild steel cylinders isi marked tac approved fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully charged complete in all respects including wall suspension bracket / trolley mounted and confoming to is:910 . 374 providing, fixing, testing and commissioning of co2 type fire extinguisher of capacity 22.5 kg filled with co2 gas as per is 15222 with controll discharge mechanism fitted with hose, horn & trolleyconfirms to is 2878 bearing isi mark. co2 cylinder as per is 7285 375 fixing, storing, handling, shifting, installation, testing and commissioning of halon free portable fire extinguishers as described below: 376 supply of fire related signages printed on photoluminescent u1000 aluminium sheet of 1.0 mm ( + 10% ) containing lumigen ii as base chemical, covered under uv stablized coating and of appropriate size for fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete. 377 fixing of fire related signages printed on photoluminescent u1000 aluminium sheet of 1.0 mm ( + 10% ) containing lumigen ii as base chemical, covered under uv stablized coating and of appropriate sizeincluding fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete in all respects as directed by engineer in charge. 378 supply ofci cover with frame light weight complete as perdesign size 600x600 mm 379 supply ofci cover with frame light weight complete as perdesign size 900x900 mm 380 boring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in is: 2800 ( part i ) , including collecting samples from different strata, preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, beyond 90 metre & upto 150 metre depth below ground level.drilling of 250 mm dia bore hole manually. 381 supply of unplasticized pvc medium well screen ( rms ) pipes with ribs, conforming to is: 12818, fittings & accessories etc. all complete, for all depths, as per direction of engineer in charge.150 mm nominal size dia 382 assembling, lowering and fixing in vertical position in bore well unplasticized pvc medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer in charge.150 mm nominal size dia 383 supply of stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. 384 supply of gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of engineer in charge. 385 supply of coarse sand of size range 1.5mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of engineer incharge. 386 filling, spreading & leveling coarse sand, gravels & stone boulders of size range 1.5 mm to 20 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of engineer incharge. 387 transportation charges of drilling equipment including assembly and other material as required. 388 drilling of 675 mm. dia by rotary machine 389 supply of 350 mm. dia housing pipe ( 8 mm. thick ) 390 laying of 350 mm. dia housing pipe ( 8 mm. thick ) 391 supply of 200 mm. dia blind pipe ( 8 mm. thick ) 392 laying of 200 mm. dia blind pipe ( 8 mm. thick ) 393 supply of 200 mm. dia slotted pipe ( 8 mm. thick ) 394 laying of 200 mm. dia slotted pipe ( 8 mm. thick ) 395 supply of 350 mm. dia socket 396 fixing of 350 mm. dia socket 397 supply of 200 mm. dia socket 398 fixing of 200 mm. dia socket 399 supply of 200 mm. dia bail plug 400 fixing of 200 mm. dia bail plug 401 supply of 350 mm. dia well cap 402 fixing of 350 mm. dia well cap 403 supply of 350x200 mm. dia reducer. 404 fixing of 350x200 mm. dia reducer. 405 supply of 350 mm. dia housing clamp 406 fixing of 350 mm. dia housing clamp 407 supply of pee gravel 2 mm. 4 mm. in side of bore after lower and development as required as per direction of e / i. 408 filling of pee gravel 2 mm. 4 mm. in side of bore after lower and development as required as per direction of e / i. 409 development by air compressor including transportation. 410 development by o.p. unit including transportation. 411 supply of 7.5 hp ksb make submersible pump set model bpd 302 / 4+uami 150 / 6 / 22 203 ( s / d ) suitable for tube well capable of pumping clear and cold water free from chemical and directly coupled with ksb electric moter operating of 415 volt suitable for 3 phase 50 cycle a.c. supply of following duty condition 7.5 hp 6 stage pipe.a discharge of water in lpm 860 approx size of discharge outlet in 80 mm.b total head of pump set 45 m. 412 supply of finolex or equivalent isi marked submersible copper cable of size 2x3x2.5 sq. mm. 413 fixing of finolex or equivalent isi marked submersible copper cable of size 2x3x2.5 sq. mm. 414 supply of control panel cubical type wall mounted vermin proof with internal wiring duly enameled painted and mechanically finished having l&t of qul. male switch fuse unit with hrc fuses, ameter, boltmeter, selector switch, phase indicating lamp with bulbs, instrument fuses, power capcitor single phase preventor etc. complete set with supply of jyoti or eq. air break star delta motro starter suitable for above submersible pump set. 415 supply of 80mm dia m.s. column pipe of class c both and socketed with heavy sockets in 3 / 6 meter length and one end flanged complete with interlocking arrangements. 416 lowering of 80mm dia m.s. column pipe of class c both and socketed with heavy sockets in 3 / 6 meter length and one end flanged complete with interlocking arrangements. 417 supply of 80mm dia m.s. column pipe clamps with nut, bolts, packing etc. 418 lowering of 80mm dia m.s. column pipe clamps with nut, bolts, packing etc. 419 supply of 80mm dia c.i. double flanged isi mark reflex valve of updadhya or equ. make. 420 fixing ofc.i. double flanged reflex valve 421 supply of 80mm dia c.i. double flanged isi mark sluice valve with hand wheel of upadhya or equ. make. 422 supply of 100 mm dia c.i. double flanged isi mark sluice valve with hand wheel of upadhya or equ. make. 423 supply of 150mm dia c.i. double flanged isi mark sluice valve with hand wheel of upadhya or equ. make. 424 fixing of 80 / 100 / 150 mm dia c.i. double flanged isi mark sluice valve with hand wheel 425 supply of c.i. double flanged bend of 80mm dia 426 fixing of c.i. double flanged bend of 80mm dia i / c cost of labour. 427 supply of 80mm dia c.i. tee heavy quality i / c cost of material. 428 fixing of 80mm dia c.i. tee heavy quality 429 supply of guru / fibing or equivalent make pressure gauge. 430 fixing of pressure gauge. 431 erection & commissioning of pumping plants complete along with electric wiring. 432 supply of steel wire rope of 1 / 2 size 433 fixing of steel wire rope of 1 / 2 size 434 s / b of 600mm x 600 mm x 6.0 mm g.i. plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia g.i. pipe and funnel for watering and one earthing lead on one no. 8 to 10 swg gi wite in 15mm dia g.i. pipe up to switch board ( from appron to switch board the cost of g.i. , pipe and g.i. wire will be extra ) 30 cm square c.i. frame with hinged cover masonry housing alternate layers of charcoal. coke and salt at least 150mm thick alround etc. as per directions of e / i complete in all respects as per drawing. 435 s / f of one number 8 to 6 swg g.i. wire in 15mm dia g.i. pipe for earthing, laid in ground or in wall duly concealed includingn the cost of cement, sand labour. t&p other material required for proper completion of the work as directed at site. 436 s / f of aluminium conductor pvc insulated armoured, served, sheathed cable 1100 volts grade16 sqmm x 4 core 437 fixing of aluminium conductor pvc insulated armoured, served, sheathed cable 1100 volts grade at a depth of 750mmbelow ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and on top.on surface the cable run shall be fixed on m.s. clamps etc. of suitable size or as directed by e / i complete in all respects the armoring of the cable shall be properly connected with the earth conductor by clamps etc.16 sqmm x 4 core 438 supply of 500 kva. 11 / 0.433 kv, 3phase, 50hz, dyn 11, oil type, ( uppcl approved make ) copper wound transformer with off load tap changing arrangement on hv side in steps of + / 2.50%, + / 5% & 7.5% , having cable end boxes on hv sideand 800 amp. bus trunking arrangement on lv side complete with all accessories i / c first filling of filtered dehydrated oil and confirming to is 2026 ( part 1 to part 5 ) & as per specification attached complete in all respects as required at site. 439 installation, testing and commissioning of 500 kva. 11 / 0.433 kv, 3phase, 50hz, dyn 11, oil type, ( uppcl approved make ) copper wound transformer with off load tap changing arrangement on hv side in steps of + / 2.50%, + / 5% & 7.5% , having cable end boxes on hv sideand 800 amp. bus trunking arrangement on lv side complete with all accessories i / c first filling of filtered dehydrated oil and confirming to is 2026 ( part 1 to part 5 ) & as per specification attached complete in all respects as required at site. 440 supply of 3 core standered aluminium conduktor xlpe ( cross linked polyethylene ) insulated pvc bedded, galvanised flat steel strip armoured cables confirming to i.s. 7098 ( part ii with latest amendments ) 11 kv grade 150sq. mm 3 core 441 laying of 3 core standered aluminium conduktor xlpe ( cross linked polyethylene ) insulated pvc bedded, galvanised flat steel strip armoured cables confirming to i.s. 7098 ( part ii with latest amendments ) 11 kv grade at a depht of 900 mm below ground level over a cushion of 100 mm thick fine river sand all around and protected with well burnt bricks in sides and on the top put across. thearmouring of cable shall be properly connected with earth condutor by clamps etc.150sq. mm 3 core 442 supply of 3 core 240sq.mm. xlpe aluminium conductor cable of 11 kv grage as required. 443 making indoor cable end jointing with cast resin compound, including lugs and other jointing materials, for 3 core 240sq.mm. xlpe aluminium conductor cable of 11 kv grage as required. 444 making outdoor cable end jointing with cast resin compound, including lugs and other jointing materials, for 3 core 240 sq.mm. xlpe aluminium conductor cable of 11 kv grage as required. 445 supply and burying of 40mm dia x 4.5 metres long g.i. pipe vertically for earthing having 12mm dia. holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of no. 6 to 8 swg gi wire in g.i. pipe up to appron ( and from appron to switch board the cost of g.i. wire and pipe will be extra ) upto switch board, 30cm square c.i. box with hinged cover masonary enclosure, funnel at top, alternate layers of charcoal / coke and salt at least 150mm thick alround etc. as per directions of engineer in charge complete in all respects as per drawing. 446 supply and burying of 600mm x 600 mmx6mm g.i. plate, vertically for earthing with its top atleast 3 mts. below ground level complete with 20mm g.i.pipe and funnel for watering and two earthing leads of no.8to10swg g.i.wire in 15mm diag.i. pipe upto switch board ( from apron to switch board the cost of g.i. pipe and g.i. wire will be extra ) 30cm. square c.i. frame with hinged cover, masonary housing, alternate layers / of charcoal / coke and salt at least 150mm thick alround etc. complete in all respects. 447 supply and burying of 600mm x 600mm x 3 mm copper plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia g.i pipe and funnel for watering and one earthing lead ofone no. 8swg copper wire in 15 mm dia g.i pipe up to switch board ( from appron to switch board the cost of g.i pipe and copper wire will be extra ) 30 cm square c.i frame with hinged cover masonry housingalternate layers of charcoal / coke and salt atleast 150mm thick alround etc. as per directions of engineer in charge complete in all respects. 448 supply and laying of 32mm x 6mm g.i. strip from earth electrode directly in the ground as required complete in all respects. 449 supply and laying of 32mm x 6 mm copper strip from earth electrode directly in the ground as required complete in all respects.. 450 supply and laying of 25mm x 3mm g.i. strip from earth electrode directly in the ground as required complete in all respects. 451 supply and fixing of one number 8 swg g.i wire in 15mm dia. g.i pipe for earthing laid in ground or in wall duly concealed including the cost of cement, sand, labour, t&p other material required for proper completion of the work as directed at site. 452 supply of aluminium conducter, pvc insulated armoured, served, sheeted cable 1000 bolts grade 453 300 sqmm3.5 core 454 185 sqmm3.5 core 455 150 sqmm3.5 core 456 35 sqmm3.5 core 457 25 sqmm3.5 core 458 16 sqmm4 core 459 10 sqmm4 core 460 16 sqmm2 core 461 10 sqmm2 core 462 6 sqmm2 core 463 laying of aluminium conducter, pvc insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the cable run shall be fixed on m.s. clamps etc. of suitable size. from 6 sqmm 2 core to 300 sqmm3.5 core 464 supply of brass nickle plated compression gland for pvc insulated & armoured served sheathed, underground cable including rubber ring etc. complete 465 300 sqmm3.5 core 466 185 sqmm3.5 core 467 150 sqmm3.5 core 468 35 sqmm3.5 core 469 25 sqmm3.5 core 470 16 sqmm4 core 471 10 sqmm4 core 472 16 sqmm2 core 473 10 sqmm2 core 474 6 sqmm2 core 475 fixing of brass nickle plated compression gland for pvc insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respects. the armouring of the cable shall be properly connected with the earth as per direction of eic. from 6 sqmm 2 core to 300 sqmm3.5 core 476 supply of palm / pin type copper tin plated cables sockets ( lugs ) to the cable leads, insuslating with tape 477 300 sqmm 478 185 sqmm 479 150 sqmm 480 95 sqmm 481 70 sqmm 482 35 sqmm 483 25 sqmm 484 16 sqmm 485 10 sqmm 486 6 sqmm 487 4 sqmm 488 fixing of palm / pin type copper tin plated cables sockets ( lugs ) to the cable leads, insuslating with tape and making of connections etc. complete in all respects as per direction of engineer incharge. from 4 sqmmto 300 sqmm 489 supply of 7 mtr gi octagonal pole of approved make ( top dia 70mm, bottom dia 130 mm and base plate 12 mm thik ) having 3mm thikness with single arm bracket ( 1 mtr length ) including the cost of foundation bolts, required t&p complete in all respect. 490 fixing of 7 mtr gi octagonal pole of approved make ( top dia 70mm, bottom dia 130 mm and base plate 12 mm thik ) having 3mm thikness with single arm bracket ( 1 mtr length ) on rcc foundation including the cost of foundation, foundation bolts, excavation & back filling and required t&p complete in all respect. 491 supply of led street light fitting having die cast aluminium body and diffuser with driver set suitable for 45 watt to 50 watt. confirming to ip 66 and above protection complete in all respect. 492 fixing of led street light fitting having die cast aluminium body and diffuser with driver set suitable for 45 watt to 50 watt. confirming to ip 66 and above protection complete in all respect. 493 supply of 6 amp to 32 amp dp mcb ( 10ka ) ( c curve ) for poles 494 fixing of 6 amp to 32 amp dp mcb ( 10ka ) ( c curve ) for poles 495 supply of decorative 40 to 45 watt led post top indirect light luminaire having pressure die cast aluminium body and clear glass with driver set confirming to ip 65 and above protection complete in all respect. 496 fixing of decorative 40 to 45 watt led post top indirect light luminaire having pressure die cast aluminium body and clear glass with driver set confirming to ip 65 and above protection complete in all respect. 497 supply offollowing capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contractors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn complete in all respect.25 amp spn 498 fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contractors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn complete in all respect.25 amp spn 499 supply of bakelite sheet 3 mm thick of suitable size & connector 500 fixing of bakelite sheet 3 mm thick of suitable size & connector 501 supply of m.s. pipe ( class b is : 1239 ) pole suitable for fixing 70 watt. hpsv post top including 4 pole cable junction box with 5 amp. rewireablefuse fitting and 5 amp. switch on laminated cover and m.s. box complete with water tight cover and 450x450x450mm base above ground and 2x4sqmm aluminium wire from cable box to lamp for connection including painting the pole on primer coats and necessary reducers on thetop of pole for fixing of post top lantern. 65mm dia 4m long ( 3m above ground and 1 m below ground ) . 502 fixing of m.s. pipe ( class b is : 1239 ) pole suitable for fixing 70 watt. hpsv post top including 4 pole cable junction box with 5 amp. rewireablefuse fitting and 5 amp. switch on laminated cover and m.s. box complete with water tight cover includingmasonary / pcc ( 1:3:6 ) work for erecting the pole and 450x450x450mm base above ground and 2x4sqmm aluminium wire from cable box to lamp for connection including painting the poleby an approved shade on primer coats and necessary reducers on thetop of pole for fixing of post top lantern.the work shall be complete as required up to the satisfaction of engg. in charge.65mm dia 4m long ( 3m above ground and 1 m below ground ) . 503 making of following size of cable chamber made of 230 mm thick brick work in cement mortar ( 1 cement : 6 sand ) with pcc 100 mm thick pcc base plastering of inner and outer surface with cement mortar including providing of heavy duty c.i cover complete with digging, refilling and removal of surplus soil complete as required. material cost will be paid saperately.900 mm x 900 mmx 1000 mm deep 504 supply of mv danger notice plate of 200 mm x 150 mm made of mild steel at least 2mmthick &vitreousenamelledwhiteon bothsides and withinscription insignalred colouronfront side as required. 505 supply of ht danger notice plate 250 mm x 200 mm made of mild steel at least 2mmthick &vitreousenamelledwhiteon bothsides and withinscription insignalred colouronfront side as required. 506 fixing of mv / ht danger notice plate 250 mm x 200 mm made of mild steel at least 2mmthick &vitreousenamelledwhiteon bothsides and withinscription insignalred colouronfront side as required. 507 supplying of fire buckets, round bottom made of g.i. sheet 9 11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of engineer in charge. 508 fixing of fire buckets, round bottom made of g.i. sheet 9 11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of engineer in charge. 509 supply of 1800 mm x 900 mm x 12 mm thick chequered rubber matting of tested quality 510 layingof 1800 mm x 900 mm x 12 mm thick chequered rubber matting of tested quality 511 supply of danger board fabricated from 10 gauge ms sheet as per ie rules 512 fixing of danger board fabricated from 10 gauge ms sheet as per ie rules 513 supply of shock treatment chart ( prescribed under i.e.rules ) duly framed with glass and supported from back with hard board or soft board. 514 fixing of shock treatment chart ( prescribed under i.e.rules ) duly framed with glass and supported from back with hard board or soft board with supply of all labour t & pfor proper completion of work. 515 supply of fire extinguishers, abc type 4.00 kg. capacity ( isi marked is : 15683 & tac approved ) complete with initial charges and wall bracket, 516 supply of co2 typefire extinguishers, 4.50 kg. capacity ( isi marked is : 2878 & tac approved ) complete with initial charges and wall bracket, 517 fixing of fire extinguishers, abc type 4.00 kg. & co2 type 4.5 kg. capacity complete with initial charges and wall bracket, along with supply of all labour for proper completion of work. 518 supply of water closet squatting pan ( indian type w.c. pan ) with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) conforming to is:7231, parryware / hindware / seabird / orient ( coral ) with all fittings and fixtures complete.white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests 519 fixing of water closet squatting pan ( indian type w.c. pan ) with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) conforming to is:7231, parryware / hindware / seabird / orient ( coral ) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests 520 supply of white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) , conforming to is : 7231, parryware / hindware / seabrid / orient ( coral ) with all fittings and fixtures complete.w.c. pan with isi marked black solid plastic seat and lid 521 fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern with manually controlled device ( handle lever ) , conforming to is : 7231, parryware / hindware / seabrid / orient ( coral ) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : w.c. pan with isi marked black solid plastic seat and lid 522 supply of white vitreous china extended wall mounting water closet of size 780x370x690mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre / 6 litre ( adjustable to 4 litre / 8 litres ) , including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. 523 fixing of white vitreous china extended wall mounting water closet of size 780x370x690mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre / 6 litre ( adjustable to 4 litre / 8 litres ) , including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. 524 supply of white vitreous china wash basin with c.i. brackets painted white, 15 mm c.p. brass pillar taps, c.p. brass chain with rubber plug, 32mm c.p. brass waste of standerd pattern. 525 a ) white vitreous china wash basin size 630x450 mm with a pair of 15 mm c.p. brass pillar taps 526 b ) white vitreous china surgeon type wash basin of size 660x460 mm with single 15 mm c.p. brass pillar tapswith elbow operated levers isi marked 527 fixing of white vitreous china wash basin with c.i. brackets painted white, 15 mm c.p. brass pillar taps, c.p. brass chain with rubber plug, 32mm c.p. brass waste of standerd pattern including cutting & making good the walls wherever required. 528 a ) white vitreous china wash basin size 630x450 mm with a pair of 15 mm c.p. brass pillar taps 529 b ) white vitreous china surgeon type wash basin of size 660x460 mm with single 15 mm c.p. brass pillar tapswith elbow operated levers isi marked 530 supply of p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. 531 semi rigid pipe 532 32 mm dia 533 40 mm dia 534 fixing of p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. 535 semi rigid pipe 536 32 mm dia 537 40 mm dia 538 supply of 600x450mm bevelled edge mirror of superior glass ( of approved quality ) complete with 6mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. 539 fixing of 600x450mm bevelled edge mirror of superior glass ( of approved quality ) complete with 6mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. 540 supply of stainless steel aisi 304 ( 18 / 8 ) kitchen sink as per is : 13983 with c.i. brackets and stainless steel plug 40mm including painting of fittings and brackets, kitchen sink with drain board size 510x1040 mm bowl depth 250mm 541 fixing of stainless steel aisi 304 ( 18 / 8 ) kitchen sink as per is : 13983 with c.i. brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherrerever required.kitchen sink with drain board size 510x1040 mm bowl depth 250mm 542 supply of white vitreous china flat back half stall urinal of size 580*380*350mm with white pvc automatic flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps ( all in d.p. brass ) with waste fitting as per is : 2556, c.i. trap with outlet grating and other couplings in c.p. brass including painting of fittings. 543 range of three half stall urinals with 10 litre pv.c. automatic flushing cistern. 544 range of two half stall urinals with 5 litre pv.c. automatic flushing cistern. 545 range of single half stall urinals with 5 litre pv.c. automatic flushing cistern. 546 fixing white vitreous china flat back half stall urinal of size 580*380*350mm with white pvc automatic flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps ( all in d.p. brass ) with waste fitting as per is : 2556, c.i. trap with outlet grating and other couplings in c.p. brass including painting of fittings and cutting and making good the walls and floors wherever required: 547 range of three half stall urinals with 10 litre pv.c. automatic flushing cistern. 548 range of two half stall urinals with 5 litre pv.c. automatic flushing cistern. 549 range of single half stall urinals with 5 litre pv.c. automatic flushing cistern. 550 fixing of stone slab table rubbed, edges rounded and polished of size 75x50cm deep and 1.8cm thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 ( 1cement: 2coarse sand: 4graded stone aggregate 6mm nominal size ) as per direction of engineer in charge and finished smooth.granite stone of approved shade 551 supply of unplasticised pvc connection pipe with brass unions 552 45 cm length 553 15 mm nominal bore 554 fixing of unplasticised pvc connection pipe with brass unions 555 45 cm length 556 15 mm nominal bore 557 supply of c.p. brass bib cock of approved quality conforming to is:8931 a ) 15 mm nominal bore 558 fixing of c.p. brass bib cock of approved quality conforming to is:8931v a ) 15 mm nominal bore 559 supply of c.p. brass long body bib cock of approved quality conforming to is standards andweighing not less than 690 gms.a ) 15 mm nominal bore 560 fixing of c.p. brass long body bib cock of approved quality conforming to is standards andweighing not less than 690 gms.a ) 15 mm nominal bore 561 supply of c.p. brass angle valve for basin mixer and gyser points of approved quality conforming to is:8931a ) 15 mm nominal bore 562 fixing of c.p. brass angle valve for basin mixer and gyser points of approved quality conforming to is:8931a ) 15 mm nominal bore 563 supply of c.p. brass shower rose with 15 or 20mm inlet 150 mm diameter 564 fixing of c.p. brass shower rose with 15 or 20mm inlet150 mm diameter 565 supply of c.p. brass stop cock ( concealed ) of standard design and of approved make conforming to is:8931: 150 mm diameter 566 fixing of c.p. brass stop cock ( concealed ) of standard design and of approved make conforming to is:8931: 150 mm diameter 567 supply of ptmt bottle trap for wash basin and sink.bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms 568 fixing of ptmt bottle trap for wash basin and sink.bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms 569 supply of ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 570 fixing of ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 571 supply of ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms 572 fixing of ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms 573 supply of unplasticised pvc pipe clips of approved design to unplasticised pvc pipes by means of 50x50x50 mm hard wood plugs, screwed with ms screws 574 110mm 575 90mm 576 fixing of unplasticised pvc pipe clips of approved design to unplasticised pvc pipes by means of 50x50x50 mm hard wood plugs, screwed with ms screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand ) and making good the wall etc. complete. 577 110mm 578 90mm 579 laying of cement concrete 1:5:10 ( 1 cement : 5 coarse sand : 10 graded stone aggregate 20mm nominal size ) around p.v.c soil and waste pipe including bed concrete as per standard design ( embedded in the flooring / ground ) 580 100 / 75 mm dia 581 supply of wall face unplasticised rigid pvc rain water pipes conforming to is: 13592 type a110 mm 582 fixing on wall face unplasticised rigid pvc rain water pipes conforming to is: 13592 type a including jointing with seal ring conforming to is: 5382 leaving 10mm gap for thermal expansion. 110 mm 583 supply of wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is:13592. 584 bend 87.5 degree 585 110 mm bend 586 shoe ( plain ) 110 mm shoe 587 fixing of wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is:13592type a including jointing with seal ring conforming to is:5382 leaving 10mm gap for thermal expansion. 588 bend 87.5 degree 589 110 mm bend 590 shoe ( plain ) 110 mm shoe 591 supply of inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 592 fixing of the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 593 supply of unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with ms screws of required length. 110 mm 594 fixing of unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with ms screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand ) and making good the wall etc. complete.110 mm 595 making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size ) over pvc sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 ( 1 cement : 3 coarse sand ) and a coat of neat cement, punning, rounding the edges and making and finishing the outlet complete. 596 supply of chlorinated polyvinyl chloride ( cpvc ) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i / c fixing the pipe with clamps at 1.00m spacing. 597 20mm dia nominal outer dia pipes 598 25mm dia nominal outer dia pipes 599 32mm dia nominal outer dia pipes 600 fixing of chlorinated polyvinyl chloride ( cpvc ) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i / c fixing the pipe with clamps at 1.00m spacing.this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of engineer in charge. 601 concealed work including cutting chases and making good the walls etc. 602 20mm dia nominal outer dia pipes 603 25mm dia nominal outer dia pipes 604 32mm dia nominal outer dia pipes 605 supply of gi pipes complete with gi fittings and clamps. 606 15mm dianominal bore 607 20mm dianominal bore 608 25mm dia nominal bore 609 32mm dia nominal bore 610 40mm dia nominal bore 611 50mm dia nominal bore 612 65mm dia nominal bore 613 fixing of gi pipes complete with gi fittings and clamps, including cutting and making good walls etc. ( internal work ) . internal work exposed on wall 614 15mm dianominal bore 615 20mm dianominal bore 616 25mm dia nominal bore 617 32mm dia nominal bore 618 40mm dia nominal bore 619 50mm dia nominal bore 620 65mm dia nominal bore 621 painting of gi pipes and fittings with synthetic enamel paint over a ready mixed priming coat, both of approved quality for new work. 622 15mm dia nominal bore 623 20mm dia nominal bore 624 25mm dia nominal bore 625 32mm dia nominal bore 626 40mm dia nominal bore 627 50mm dia nominal bore 628 65mm dia nominal bore 629 supply of gi union in gi pipes 630 15mm dia nominal bore 631 20mm dia nominal bore 632 25mm dia nominal bore 633 32mm dia nominal bore 634 40mm dia nominal bore 635 50mm dia nominal bore 636 65mm dia nominal bore 637 fixing of gi union in gi pipes including cutting and threading the pipe and making long screws etc. complete ( new work ) . 638 15mm dia nominal bore 639 20mm dia nominal bore 640 25mm dia nominal bore 641 32mm dia nominal bore 642 40mm dia nominal bore 643 50mm dia nominal bore 644 65mm dia nominal bore 645 supply of gun metal gate valve with wheel of approved quality. 646 25mm dia nominal bore 647 32mm dia nominal bore 648 40mm dia nominal bore 649 50mm dia nominal bore 650 65mm dia nominal bore 651 fixing of gun metal gate valve with wheel of approved quality. 652 25mm dia nominal bore 653 32mm dia nominal bore 654 40mm dia nominal bore 655 50mm dia nominal bore 656 65mm dia nominal bore 657 supply of brass stop cock of approved quality. 658 b ) 20 mm nominal bore 659 fixing of brass stop cock of approved quality. 660 b ) 20 mm nominal bore 661 supply of terrace ( at all floor levels ) polyethylene water storage tank isi : 12701 marked indicating the bis license no. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fitting and base support for tank. [ sintex, electroplast, star, lotus or equivalent having valid isi license ] . 662 fixing & placing of terrace ( at all floor levels ) polyethylene water storage tank isi : 12701 marked indicating the bis license no. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fitting and base support for tank. [ sintex, electroplast, star, lotus or equivalent having valid isi license ] . 663 supply of glazed stoneware pipes grade a100mm dia sw pipe 664 laying and jointing glazed stoneware pipes grade a with stiff mixture of cement mortar in the proportion of 1:1 ( 1 cement : 1 fine sand ) including testing of joints etc. complete.100mm dia sw pipe 665 laying cement concrete 1:5:10 ( 1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size ) all rounds.w. pipes including bed concrete as per standard design 100mm dia sw pipe 666 supply of square mouth s.w. gully trap grade‘a’ complete with c.i. grating, water tight c.i. cover with frame of 300 x300 mm size ( inside ) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 150 x 100 mm size p type 667 fixing of square mouth s.w. gully trap grade‘a’ complete with c.i. grating, brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size ( inside ) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design150 x 100 mm size p type 668 supply of floor and wall face ringfit upvc astral ultradrain conventional system for soil and waste water pipes conforming to ( hsn code: 3917 ) type b ( i ) double socketed pipes. 669 a ) 110mm dia p.v.c. pipe 670 b ) 90mm dia p.v.c. pipe 671 fixing of floor and wall face ringfit upvc astral ultradrain conventional system for soil and waste water pipes conforming to ( hsn code: 3917 ) type b including jointing with seal ring. ( i ) double socketed pipes. 672 a ) 110mm dia p.v.c. pipe 673 b ) 90mm dia p.v.c. pipe 674 supply of upvc floor trap of self cleansing designwith cp jalicomplete in all respects. ( make : supreme / finolex / prince ) p trap type floor trap 110 x 90mm 675 fixing of upvc floor trap of self cleansing designwith cp jalicomplete in all respects. ( make : supreme / finolex / prince ) p trap type floor trap 110 x 90mm 676 supply of clean out plug ( astral ) 677 fixing of clean out plug ( astral ) 678 supply ofterminal guard. 679 a ) 110mm 680 b ) 90mm 681 fixing of terminal guard. 682 a ) 110mm 683 b ) 90mm 684 supply of wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes. 685 110mm bend 686 90 mm bend 687 110mm coupler 688 90mmcoupler 689 110x110x110 mm single tee with door 690 90x90x90 mm single tee with door 691 fixing of wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. 692 110mm bend 693 90 mm bend 694 110mm coupler 695 90mmcoupler 696 110x110x110 mm single tee with door 697 90x90x90 mm single tee with door 698 supply of 1.50 sqmm frlsh pvc insulated single core copper conductor cable 699 supply of 2.50 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable 700 supply of 4.00 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable 701 supply of 6.00 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable 702 supply of 10 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable 703 supply of 16 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable 704 supply of 25 sqmm frlsh pvc insulated 1100 v single core multistrand copper conductor cable 705 supply of hexagonal / round gp fan box of approved make made up of 1 mm thick isi marked gp sheet spot welded four to eight holes of 25.4 mm for pipe entry of the box duly screewed fitted with 300 mm round zink coated ms bar x 12 mm. 706 supply of ceiling fan with fan motor of ac permanent insulation, capacitor rating conforming to bee 5 star. the ratrd voltage220 / 240 volts, 50 hz, single phase, ac the fan assemble should consists of down road blades, shackle canopies with double ball bearing system – 1200 mm sweep 707 supply of electronic fan regulator ( modular ) 120 280 v isi marked 708 supply of led tube light with metal heavy duty box type batten light fitting 2x 22 watt suitable for 2x22 watt polycarbonate tube light including tube etc suitable for both surface. 709 supply of led tube light with metal heavy duty box type batten light fitting 1x 22 watt suitable for 1x22 watt polycarbonate tube light including tube etc suitable for both surface. 710 supply of recess / surface mounting round 10 to 15 watt, cut out 125 mm, height min 40 mm, led downlighter having powder coated die cast aluminium housing with heat sink, diffuser / reflector and driver set, suitable for 24 hr continuousoperation 711 supply of single led light wall bracket on matching mdfeg board base 712 water tight oblong 10 watt led bulkhead luminery with driver set conforming to ip 65 and above protection complete. 713 supply of surface / flush mounting distribution boards with additional metal door without mcb complete. ( cat a ) 714 4 way tpn 715 6 way tpn 716 8 way tpn 717 supply of 6 amp to 32 amp ( 10 ka ) sp mcb ( cat a ) 718 supply of following mcbs 719 40 amp. fp mcb ( cat a ) 720 63 amp. fp mcb ( cat a ) 721 40 amp. tp mcb ( cat a ) 722 63 amp. tp mcb ( cat a ) 723 supply of surface / flush mounting v tpn distribution boards with additional metal door without mcb complete. 4 way v tpn 724 supply of following mccbs 725 63 amp. fp mccb ( cat a ) 726 100 amp. fp mccb ( cat a ) 727 125 amp. fp mccb ( cat a ) 728 160 amp. fp mccb ( cat a ) 729 supply of power plug with 15 a / 250 v flush type switch and 5 pin 15 a / 250 v flush type universal socket in suitable ms box 175mmx100mmx50mm size ( modular ) 730 supply of single pole mcbs blanking plate complete 731 supply of gi plate for earthing size 600 mm x 600mm x 6 mm 732 supply of gi pipe 20 mm dia 733 supply of gi wire 8 to 10 swg 734 supply of ci frame ( 30 sqcm ) with hinged cover 735 supply of gi strip for earthing purpose 25 mmx 3 mm 736 supply of aluminium conductor pvc insulated armoured, served, sheeted cable 1000 volts 737 95 sqmm 3.5 core 738 70 sqmm 3.5 core 739 50 sqmm 3.5 core 740 35 sqmm 3.5 core 741 25 sqmm 3.5 core 742 10 sqmm 4 core 743 supply of brass nickle plated compression gland for pvc insulated and armoured served sheeted underground cable including rubber ring 744 95 sqmm 3.5 core 745 70 sqmm 3.5 core 746 50 sqmm 3.5 core 747 35 sqmm 3.5 core 748 25 sqmm 3.5 core 749 10 sqmm 4 core 750 supply of palm / pin type copper tin plated cable sockets ( lugs ) to the cable leads, insulating with tape 751 95 sqmm 752 70 sqmm 753 50 sqmm 754 35 sqmm 755 25 sqmm 756 16 sqmm 757 10 sqmm 758 6 sqmm 759 supply of gi box alonwith modular base and cover plate for modular switches in recess1 or 2 module ( 75 mmx75 mm ) 760 supply of telephone socket outlet ( modular ) 761 supply of tv antenna socket outlet ( modular ) 762 supply of bell push ( modular ) 763 supply of call bell / buzzer suitable single phase 230 v 764 supply of telephone cable following pair 0.5 sqmm fr pvc insulated annealed copper conductor, unarmoured 765 2 pair 766 10 pair 767 20 pair 768 supply of co axial tv cable rg 6 grade 0.7 mm solid copper conductor pe insulated sheeted with fine tinned copper braid and protected with pvc sheet 769 supply of 10 pair junction boxes for floors and building with krone connectors 770 supply of 20 pair junction boxes for floors and building with krone connectors 771 supply of 50 pair junction boxes for floors and building with krone connectors 772 supply of exhaust fan of ac 230 / 250 v, 50 hz including nuts & bolts, mounting frame and other accessories.300 mm sweep 773 supply of energy meter ( 3 phase ) and other accessories. 774 supply of wall fanof ac 230 / 250 v, 50 hz including nuts & bolts, mounting frame and other accessories. 450 mm sweep 775 supply of exhaust fan of ac 230 / 250 v, 50 hz including nuts & bolts, mounting frame and other accessories.450 mm sweep 776 supply of weired decorative mirror light suitable 9 watt led with lamp complete 777 supply of factory weired integral led flood light luminaries with die cast aluminium housing built with driver set suitable for 40 to 50 watt confoming to ip 65 / 66 protection complete. 778 supply of swiches ( modular ) 5 amp 779 supply of sockets ( modular ) 5 amp 780 supply of pvc conduit pipe 25 mm dia 781 supply of round sheet 782 supply of ceiling rose 783 supply of holder for bulbs 784 fixing of main lt panel 785 fixing of main em panel 786 fixing of sub panel 787 fixing of sub em panel 788 fixing of capacitor panel 150kvar 789 fixing of feeder piller 790 fixing of street feeder piller 791 supply of coarse sand 792 supply of cement50 kg 793 supply of brick m150 794 supply of stone grit 20 mm 795 supply of stone ballast 40 mm 796 supply of tor steel 8 mm dia 797 supply of tor steel 10 mm dia 798 supply of tor steel 12 mm dia 799 supply of tor steel 16 mm dia 800 supply of tor steel 20 mm dia 801 supply of tor steel 25 mm dia 802 supply of ms fabrication for door window and ventilator 803 supply of water proofing chemical cico tapecrete p151 804 supply of y shaped angle iron post 40x40x6 805 supply of kota stone 22 mm thick 806 supply of vitriried floor tile 8 to 10 mm thick in 600x600 mm size 807 supply of wall tile glazed / ceramic floor tiles 808 supply of ss railing 304 grade 809 supply of ms collapsible channel 810 supply of rolling shutter with ball bearing 811 supply of granite 812 supply of cinder 813 supply ofchequred tile 300x300 mm size 814 supply of ms gate made of ms hollow sections 815 supply of interlocking pavers 80 mm m30 mpa...

Military Engineer Services - Uttar Pradesh

36367153 tender for repair / maintenance of b / r items, joinery, periodical service and allied works in technical, residential, parachute building and auditorium at adrde agra under ge i rnd delhi 1 taking down cement plaster on brick / stone walls etc any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 2 m&l for rendering 15mmthick plaster on any faces of brick work in cm 1:6 finished even and fair complete all as specified and directed. 3 m&l rendering 15 mm thick plaster on fair faces of brick / concrete surfaces as in cm 1:4 mixed with wpc finished surfaceeven and fair complete all as specified and directed.note : wpc shall be measured and paid separately as supply only. 4 m&l for rendering 10mmthick plaster on concrete surfaces of ceiling in cm 1:3 finished the surface fair & even complete all as specified and directed. 5 m&l for rendering plaster 15mmthick on concrete surfaces of walls in cm 1:3 and finished the surface fair & smooth with using using wpc and applying neeru finish to plasteredsurfaceas in water tanks etc complete all as specified and directed.note: wpc shall be measured and paid separately as supply only. 6 m&lfor preparation of newly plastered surfaces and applying 3 coats of white wash on ceiling including complete all as specified and directed. 7 m&l for preparation of new plastered of new plastered surface of walls and applying 2mm thick wall care putty in two layers ( each layer minimum 1mm thick ) complete all as specified and directed. 8 m&l for preparation of new plastered surface of walls and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed. 9 m&l for preparation of new plastered surfaces of walls and applying two or more coats of acrylic smooth exteriorpaint of required shade and applied over a coat of exterior primer @ 2.20 kg / 10 sqmcomplete all as specified and directed. 10 m&l for complete removal of the existing surface of walls and applying two coats of white wash complete all as specified and directed. 11 m&l for preparation of oldplastered surfaces of walls and applying two coats of exterior emulsion paint complete all as specified and directed. 12 m&l complete removal of existing treatment of wall including cornices etc and making good by filling holes and applying two coat of oil bound distemper over a coat of primer complete all as specified and directed. 13 m&l for preparation of old painted wood and wood based surface of any description not otherwise discribed over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 14 all as per item ser no 13.00 above but on old painted steel or iron surface. 15 supply only integral water proofing compound complete all as specified and directed. 16 s&f in repair mild steel work as in framed brakets of angles or tees with web and flanges out to shape, drilled and countersunk for screw, including bending and welding angles as necessary gusset plates, riveting etc not exceeding 10 kg each bracket conferming to fe 410 or fe 310 0 complete all as specified and directed. 17 m&l for 40 mm thick sand stone slabs in shades, chajjas, shelves etc not exceeding 2m lengh, punched dressed on face and along exposed edges self faced on other side and setin cm 1:4 and pointed in cm 1:2 including taking down / dismantling old unserviceable stone slabs complete all as specified and directed. 18 cutting chases, pinning in, making good to facings where required and pointing in cm 1:3 to ends or edges of landings, steps cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting exceeding 20cm girth in brick work complete all as specified and directed. 19 m&l 25 to 30 mm thick dholpur stone cladding, gang saw cut with machine cut edges, uniform colour of each stone size not exceeding 0.25 sqm fixed with and including, making v groove at top and at bottom of stone and drilling holes for hold fastener, polishing, rubbing & including silicon treatment complete all as specified and directed. 20 refastening and securing ends of balusters, newels, rag bolts etc, let into stone and grouted in cement mortar including resecuring the mortices and regrouting in cement mortar complete all as specified and directed. 21 taking down chowkats or frames with shutters ( without taking off shutters from the frames ) area not exceeding 1.5 sqm each and making good the distrubed surface complete all as specified and directed. 22 taking down chowkats or frames exceeding 1.5 sqm but not exceeding 4 sqm each with shutters ( without taking off shutters from the frames ) and making good the distrubed surface complete all as specified and directed. 23 taking down shutter of any description not exceeding 1 sqm each complete all as specified and directed. 24 taking down shutter of any description exceeding 1 sqm and not exceeding 2 sqm each complete all as specified and directed. 25 taking down shutters of any description exceeding 2 sqm each complete all as specified and directed. 26 s&f pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed. 27 m&l for 35mm thick 2nd class hard wood factory made plain framed panelled shutter ( any number of panels ) , with lock rail and panel of 12mm thick bwp veneered particle board with commercial veneering on both faces.the sizes of rails and stiles as per is:1003 ( part i ) kiln seasoned and chemically pressure treated fitted to chowkats complete all as specified and directed. 28 m&l for 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. 29 s&f factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails. m.s. frame shall be covered with heat moulded plain colour pvc c channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing shown in ssr complete all as specified and directed. 30 s&f factory made pvc door frames of size 50mmx47 mm made out of 5mm plain colour pvc sheet reinforced with ms square tube suitable for opening as per site condition complete all as specified and directed. 31 s&f 100mm stainless steel butt hinges, medium weight, cold rolledstainless steel, and fixed complete all as specified and directed. 32 s&f 300 mm long aluminium alloy, anodised sliding door bolts, plate type, and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminum alloy complete all as specified and directed. 33 s&f 250 mm long aluminium alloy, anodised sliding door bolts, plate type, and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminium alloy complete all as specified and directed. 34 s&f in repair 250 mm long aluminum alloy, anodised sliding door bolts, plate type, and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminium alloy complete all as specified and directed. 35 s&f 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed. 36 all as per item ser no 35.00 above but 150 mm size. 37 s&f in repairs 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed. 38 s&f 150mm long aluminium handles, fabricated type, d shape, anodized and fixed complete all as specified and directed. 39 s&f in repairs150mm long aluminium handles, fabricated type, d shape, anodized and fixed complete all as specified and directed. 40 s&f 140mm long floor door stopper aluminium alloy body and tongue, anodized with hard drawn steel spring fixed in floor complete all as specified and directed. 41 s&f in repairs140mm long floor door stopper aluminium alloy body and tongue, anodized with hard drawn steel spring fixed in floor complete all as specified and directed. 42 s&f in repairs door closer aluminium ( die cast ) body hydraulically regulated, designation no. 3 universal type, suitable for door shutters of 851 1000 mm in width and of weight 61 to 80 kgscomplete all as specified and directed. 43 hacking out old broken glass ( any thickness, size, quality or description ) from metal frame including punching or drilling out old glazing pins / spring clips providing and fixing new ones complete all as specified and directed. 44 s&f 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and directed. 45 s&f 4.8mm thick sheet glass ordinary quality and glazing with oil putty in square exceeding 0.5 sqm in each pane complete all as specified and directed. 46 s&f 4mm thick figured glass, pin headed type and glazing with oil putty in square not exceeding 0.5 sqm each pane complete all as specified and directed. 47 s&f in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 48 m&l for preparation of new wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 49 m&l for preparation of new steel or iron surface and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 50 demolition of cement concrete ( unreinforced ) in ground floors and pavings not exceeding 15 cm thickness ( below or above ground level ) complete all as specified and directed. 51 m&l 100mm thick pcc 1:2:4 type b 1 ( 20mm graded stone aggregate ) including necessary form work as in path, passages, etc, surface finished even & fair & spike rolling to surfaces or making impressions of expanded metal, while the concrete is green complete all as specified and directed. 52 m&l for 50mm thick pcc 1:3:6 type c2 ( using 40mm graded stone aggregate ) as in plinth / path protection 75mm thick laid in bays including finishing the concrete surface even and smooth without using extra cement complete all as specified and directed.note : the units rate qouted shall be deemed to include for providing the concrete in alternate bays exc 3 mtr long with 12mm wide and 50mm deep joint between the bays which shall be filled with mastic filling with hot bitumen vg 10 and 1:2 mix by volume. 53 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) including rubbish off the premises complete all as specified and directed. 54 m&l for ist quality non skid ceramic colouredtiles 7mm to 8mm thick, ( square or rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over 15m thick screed bed in cm 1:6 complete all as specified and directed. 55 m&l for ist quality glazed ceramic coloured tiles of size 300x200 6 to 7 mm thick on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over 10mm thick rendering in cm 1:4 complete all as specified and directed. 56 m&l coloured chequeredcement concrete tiles 25cm x 25cm x 22mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment in floors laid over 15mm thick screed bed in cm 1:6 complete all as specified and directed. 57 demolition of brick or concretetile ( laid flat or on edge ) laid in floor, channel, kerb, apron etc laid dry complete all as specified and directed. 58 m&l for machine pressed precast concrete interlocking paver block 60mm thick, m 35 grade with grey cement and no pigment any shape and size confirming to is 15658 2006 laid in floors over and including 25mm thick river sand complete all as specified and directed. 59 blank 60 m&l for premium quality fully vitrified tiles light shade 10 mm thick ( square or rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in floors and jointed in neat cement slurry and pointed in white or coloured cement to matchthe shade of tiles laid over 15mm thick screed bed in cm 1:6 complete all as specified and directed. 61 demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed. 62 m&l for 20mm thick granite ( of any type ) work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platforms and like including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade laid over 20mm thick screed bed in cm 1:4 complete all as specified and directed. 63 m&l for kota stone slab flooring 20 25mm thick laid and jointed withgrey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over 20mm thick screed bed in cm 1:6complete all as specified and directed. 64 m&l for kota stone slab 15 to 18 mm thick in riser of steps, skirting, dado and pillar etc and jointed withgrey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over 15mm thick rendering in cm 1:4 complete all as specified and directed. 65 dismantling of existing roof treatment any descriptionincluding lime / cement concrete on roof slab and clean the surface as well complete including removal of debris away from the site complete all as specified and directed. 66 m&l 40mm thick brick tiles laid over 15mm thick screed bed in cm 1:6 and joints grouted flush in cm 1:3 mixed with 5% of crude oil by weight of cement complete all as specified and directed. 67 m&l for screed bed 10mm thick in cm 1:4 mixed with water profing compound @ 3% by weight of cement or as per manufacturers instruction complete all as specified and directed.note : wpc shall be measured and paid seperately. 68 m&l for roof treatment with polymeric membrane ( app based ) with non woven polyester mat as reinforcement with following as given here under over the prepared roof surface by applying a coat of cold bitumen 85 / 25 based primer on entire surface @ 0.30 ltr / sqm on dry and clean surface and a coat of blown bitumen 85 / 25 grade @ 1.2 kg / sqm and applying further treatment as under: ( i ) m&l for a layer of app based polymeric membrane minimum weighing not less than 3kg / sqm and minium 3mm thick reinforced with polyster non woven fabric ( wt. not less than 150 gms ) and on primed surface by forced application complete all as specified. ( ii ) m&l for applying evenly a tack coat of industrial bitumen 85 / 25 at the rate of 1.2 kg per sqm including cleaning surfaces.note: ponding test with filling of water for continuous 48 hours complete all as specified and directed. 69 m&l for pcc 1:2:4 type b 0 ( using 12.5mm graded stone aggregate ) as in coping, coving, padding, bed plates or mass etc. complete all as specified and directed. 70 taking up or down steel tubing and connections 15mm bore complete all as specified and directed. 71 all as per item ser no. 70.00 above but 20mm dia. 72 all as per item ser no. 70.00 above but 25mm dia. 73 s&f gi tube medium grade galvanised 15 mm bore with all new fittings fixed to wall and ceilings or laid in floor complete all as specified and directed. 74 s&f gi tube medium grade galvanised 20 mm bore with all new fittings fixed to wall and ceilings or laid in floor complete all as specified and directed. 75 s&f gi tube medium grade galvanised 25 mm bore with all fittings fixed to wall and ceilings or laid in floor complete all as specified and directed. 76 s&f 20mm ball brass valves high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. 77 s&f in repair 15mm bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. 78 s&f in repair 15mm stop valves cast copper alloy chromium plated fancy type long shank concealed type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. 79 s&f in repair 15mm bib taps standard of ptmt any colour high pressure screwed for iron pipe and fixed ( minium weight 15mm 90gms ) complete all as specified and directed. 80 s&f in repair 15mm stop valve of ptmt any colour high pressure screwed for iron pipe and fixed ( minium weight 15mm 90gms ) complete all as specified and directed. 81 s&f in repairs vitreous china squatting pan, orissa pattern , size 580x440 mm white, with integral foot rests ( excluding flushing cistern and flush pipe ) but including 110mm pvc ( swr ) wc connector with lip ring andpvc ( swr ) p / s trap 110mm complete all as specified and directed. 82 s&f in repairs vitreous china wash down water closet pan ( pedastal pattern ) , white ( excluding fixing bolt etc complete all as specified and directed. 83 s&f plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinge device complete all as specified and directed. 84 s&f in repairs low level flushing cistern of capacity 10 litre isi marked complete with inlet ball valve and handle including bracket complete all as specified and directed. 85 s&f in repairs vitreous china wash hand basin, white flat back, size 630x450mm excluding tap etc but including brackets complete all as specified and directed. 86 s&f in repairs vitreous china urinal half stall type, white as per exisiting size complete all as specified and directed. 87 s&f in repair 40 mm bore low density polyethylene pipe of pressure rating 6kgf / sqcm complete all as specified and directed. 88 s&f in repair 32 mm bore low density polyethylene pipe with waste coupling for wash hand basin complete allas specified and directed. 89 s&f in repair 15mm dia pillar tap cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered hot and cold with long screwed shanks and fly nuts screwed for iron pipecomplete all as specified and directed. 90 s&f in repair 15mm dia pillar tap of ptmt any colour high pressure screwed for iron pipe and fixed minimum weight 120 gms ) complete all as specified and directed. 91 s&f in repair ball valve high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 25mm bore ( weight 455 gms ) complete all as specified and directed. 92 s&f in repair ball valve high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20mm bore ( weight 210 gms ) complete all as specified and directed. 93 s&f 600mm x 450 mm bevelled edge mirror of selected quality gless, moulmted on 6mm thick ac building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washer complete all as specified and directed. 94 s&f in repair chromium plated shower roses with or without swivel joints 125mm size, including fixing to steel pipe or union complete all as specified and directed. 95 s&f grating square 150mm size of ptmt ( minimum weight 100 gms ) complete all as specified and directed. 96 s&f grating doom 150 mm dia with waste hole of ptmt. ( minimum weight 100 gms ) complete all as specified and directed. 97 s&f in repairs pvc connection 15mm size with ptmt nuts of length 450mm complete all as specified and directed. 98 s&f 32mm waste coupling of ptmt ( half or full threaded ) minimum weight 45gms for urinals complete all as specified and directed. 99 s&f in repair bottle trap 32 mm bore of ptmt having minium water seal 25 mm weight 260 gms for wash basin with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified and directed. 100 s&f in repairs pvc 75mm ( swr ) floor trap, plane with grating including jointing with solvant cement complete all as specified and directed. 101 taking down eaves gutters and rainwater pipes ( any size or pattern ) , including all fittings, heads, shoes, bends, swan necks, etc complete all as specified and directed. 102 s&f for 110mm bore pvc ( swr ) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed. 103 all as per ser item no. 102.00 above but 75mm bore. 104 s&f 75mm dia pvc ( swr ) bends any radius complete all as specified and directed. 105 s&f 110mm dia pvc ( swr ) bends any radius complete all as specified and directed. 106 s&f 110mm dia pvc ( swr ) junction single ( single t ) equal or unequal complete all as specified and directed. 107 s&f 75mm dia pvc ( swr ) vent cowl complete all as specified and directed. 108 demolition of brick work or stone masonry built in cement mortar including all quoins arches, pillars etc complete all as specified and directed. 109 m&l for brick work with sub class b old size bricks straight or corved on plan exceeding 6 m mean radius built in cm 1:4 complete all as specified and directed. 110 dismantling of water tanks and removing to store exceeding 250 litres but not exceeding 500 litres complete all as specified and directed. 111 dismantling of water tanks and removing to store exceeding 500 litres but not exceeding 1000 litres complete all as specified and directed. 112 m&l for rotational moulded polyethylene water storage tank triple layered 500 litres capacity ( cylindrical vertical with closed top ) hoisted in position complete all as specified and directed. 113 m&l for rotational moulded polyethylene water storage tank triple layered 1000 litres capacity ( cylindrical vertical with closed top ) hoisted in position complete all as specified and directed. 114 s&f in repairs health faucet brass chromium plated with 900mm long pvc connection pipe 15 mm dia with brass sockets complete all as specified and directed. 115 s&f in repairs brass jet spray chromium plated with 900mm long pvc connection pipe 15 mm dia with brass sockets for europian water closet complete all as specified and directed. 116 s&f in repairs pvc connection 15mm size with ptmt nuts of length 900mm complete all as specified and directed. 117 s&f anodised aluminium frame size 101.5x45x2mm thick for doors, windows, ventilator with one or more rebates including jointing cleat for fixing etc complete all as specified and directed. 118 s&f anodised aluminium door shutters, aluminium section weighing 0.55 kg / m including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 nos in each door shutter, aluminiumhinges, anodised aluminiumsnap beading, screws etc complete all as specified and directed.note : bottom & lock rail shall be of aluminium section 45mmx114x 1.41mm thick. 119 s&f anodised aluminium window and ventilator shutter, fixed type without sash bar, aluminium section weighing 0.55kg / m including necessary jointing cleat, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed. 120 s&f anodised aluminium window and ventilator shutter, side hungtype without sash bar, aluminium section weighing 0.55kg / m including necessary jointing cleat, glazing clips, rubber packing, anodised aluminium snap beading, screws, aluminium anodised fittings such as peg stays 150mm long ( 01 no ) , hinge type b 21 100mm long ( 02 nos ) suitable handles ( 01 no ) complete all as specified and directed. 121 s&f in repair anodised aluminium grill ( anodised transparent or dyed to required shade according to is : 1886 with minium anodic coating of grade ac 15 ) of approved design / pattern, with approved standard section and fixed to the existing windows frame with cp brass / stainless steel screw @200 mmm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the openingall complete as per requirement and direction complete all as specified and directed. 122 s&f in repair double action floor door spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made out of brass, other part made of mild steel heavy duty and fixed complete all as specified and directed. 123 repairs to rolling shutter of any size and description with or without gear box including taking down if required, easing of shutter, greasing / oiling to ball bearing, springs and guide channels, gear box etc, straightening of guide channels, choring rod and , hasp and stapples, welding where ever necessary and refixing in its original position after repairs etc complete all as specified and directed. 124 s&f in repairs ball bearing of rolling shutter gear or without gear operated complete all as specified and directed. 125 s&f in repairs spring for rolling shutter best qualitycomplete all as specified and directed. 126 s&f in repairs outer garari for rolling shutter shaftcomplete all as specified and directed. 127 s&f in repairs gear shaftgarari for rolling shutter complete all as specified and directed. 128 s&f in repairs ms strip made out of 1.25mm thick sheet in rolling shutter including locking the same and match with existing strips etc complete all as specified and directed. 129 s&f in replacement of existing gear box forrolling shutterwidth upto 4m, best qualitycomplete all as specified and directed. 130 s&f in replacement of existing gear box forrolling shutterwidth above 4 to 6m, best qualitycomplete all as specified and directed. 131 m&l for preparation of old plastered surface of walls and applying one coat of exterior emulsion paint complete all as specified and directed. 132 m&l for applying two coats of oil bound distemper over a coat of alkali resistant primer on ceilng surface including preparation of new plastered surface complete all as specified and directed. 133 m&l complete removal of existing treatment of ceiling including cornices etc and making good of filling holes and applying two coat of oil bound distemperover a coat of primer complete all as specified and directed. 134 m&lcomplete removal of existing treatment of walls including cornices etc and making good of filling holes and and two coats of wall care putty ( 1mm each coat ) and finishing wall with textured exterior paint of required shade new work ( two or more coats applied @1.67ltr / 10 sqm over and including priming coat off exterior primer applied @ 2.20 kg / 10 sqm complete all as specified and directed. 135 m&lfor preparation of old plastered surfacesof ceiling and applying one coat of white wash complete all as specified and directed. 136 m&l for applying one coat of oil bound distemper on walls including preparation of old plastered surface complete all as specified and directed. 137 m&l for preparation of old plastered surface of walls and applying two of oil bound distemper complete all as specified and directed. 138 m&l for french polishing with one or more coat on old wooden surfaces of any description, width or girth including cleaning and preparing the the surfacescomplete all as specified and directed. 139 m&l forpreparation of old steel surfaces of any description, over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 140 s&f in repair rubber beading for fixing glass pane in aluminium door / windows where applicable in squareexceeding 0.5 sqm in each pane complete all as specified and directed. 141 s&f in repairs sun light relective / solar film to glass pane of any approved colour complete all as specified and directed. 142 s&f in repairs mortice lock brass, 4 lever of size 100 vertical type fixed to aluminium doors including duplicate keys etc complete all as specified and directed. 143 s&f in repair 15mm stop valves 3 way cast copper alloy chromium plated fancy type long shank concealed type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed. 144 s&f in repairs toilet paper holder brass chromium platedcomplete all as specified and directed. 145 m&l for point contact of wood work by chemical emulsion ( in oil or kerosene based solution ) @ 0.5 ltr / holes by drilling 6mm dia holes at downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed....

Military Engineer Services - Uttar Pradesh

36277085 provision of borewell in tech area and upgradation of stores at various location at north camp under ge ( af ) bamrauli trial bore well of 200 mm dia size pilot bore through any soil strata including hard stone / boulder by means of directrotary method below ground level complete all as specified & directed by engineer in charge. note: unit rate quoted by tender shall be deemed to include cost of ms pipe and transportation of rig accessories required, developing and testing etc at site of work and removal of the same on completion from the site including necessary supervision and rent charges of rig machine compressor & op unit ( any other t&p not specifically mentioned ) in respective item of sch aand no extra payment shall be admissible on this account. 2 drilling reaming vertical bore 525 mm dia at approved site / location in any type of strata for 250erw casing pipe for various depth as shown below including all works pertaining to boring complete in all respect and all as specified & directed. 3 ( a ) reaming up to 525 mm dia for 60 mtr depth from ground level for casing pipe 250 mm dia. 4 ( b ) reaming up to 525 mm dia for exceeding 60 mtr to 150 mtr for casing pipe of 200 mm dia. 5 supply and assembly including jointing, lowerings and fixing in position erw plain steel pipe ( seamless ) housing pipe 250 mm bore ( nominal dia ) 8.00mm thick and outer dia of pipe 266 mm conforming to is 8110 2000 class 8.1.1 plain end pipe jointed and welded couper ring ( welding shall be done through out the circumference of the pipe and coupler ring both sides all as specified and directed by eic. make : jindal / tata. note : ( a ) length of pipe shall not less than 2.40 mtr except where the pipe length required is less than 2.40m ( b ) effective length shall only be measured and paid. 6 all as per item no 3 above but supply assembling, jointing plain ms pipe ( seamless ) casing 200 mm bore 8 mm thick and outer dia of pipe 216 mm conforming to is 8110 2000 complete and lowering and fixing position after socket reducer of 250x200mm bore. 7 s&f ms strainer ( slotted ) pipe v weired 200 mm bore, 8 mm thick conforming to is 8110 2000 fabricated with pipe or specification mentioned above ( item no 3 ) slot of size 1.55mmx75mm as per is provn uniformly distributed on the surface all as specified. 8 s&f mild steel reducing socket 250mmx200mm dia of suitable length including welding, mild steel strip 40x6mm 2 nos on each joint extended in 75mm on each side all as specified. ( the wall thickness of socket not less than 8 mm thick. 9 s&f wrought iron bail plug 200 mm bore, all as specified. 10 s&f well cap for 266 mm dia housing pipe all as specified and directed. 11 s&f two nos ms flat iron 150 mm x 15 mm housing clamp for holding to 250 mm dia housing pipe with 16mm ms bolt & washers including casting of pcc blocks 1:2:4 type b 1 using 20mm graded stone aggregate of size 1.20 m x 1.00 m including 50mm dia ms pipe 2 nos each 1.5mtr long with cap plug and cap top for filling pea gravel including necessary excavation & each work in any type of soil complete all as specified and directed. 12 m&l for packing pea gravel of size 3 to 5mm natural shape brought direct from river bank and packing around casing pipe to entire depth up to ground level all as specified anddirected. ( length of assembly packed only be measured for payment ) 13 development of tube well by means ofhigh velocity compressored airwith 350 psi air compressor all as specified in is 11189 1985 para 4.2including arrangment for equipment fitting. 14 supply of sodium meta hexa phosphate for disinfecation of bore well all as specified and directed. 15 development of tubewell bymeans of over pumping for subsequent hours until clear discharge as per clause 9.3.2 of is 2800 ( part 1 ) 1991all as specified and directed. 16 supply only strata sample box with glass cover 3mm thick and having internal dimension 1.0 mtr x 0.60 mtr x 0.10 mtr made out of shisham plank 20mm thick with hinges, hasp and staples including polishing complete with samples at various depth met at the time of boring including stata chart in duplicate. 17 chemical bilogical and potability testing of water sample taken from the bore at govt approvedlaboratories. note: test certificate obtained from approved lab will be submitted by the contractor in original. 18 yield testing for bore well by continuous pumping for 16 hrs to determine safe pumping yield of the tube well as perclause 5 of is 2800 ( part ii ) 1979 complete all as specified and directed. 19 electric logging in trial bore precise delineation of granular zones and also the quality of ground water including report interpreatation complete all as specified and directed. note: electric logging shall be carried out by approved agency. 20 s&f air release valve suitable to connect column pipe of rising main flanged and column pipe or submersible pump set compelte with nut, bolt washer etc including grouting 4 bolt on pcc plateform all specified 21 supply, lowering, jointing and testing ms black column pipe 3 mtr long heavy duty 100 mm bore wall thickness 5 mm both ends flanged with heavy duty ms flanged not less than 16 mm screwed and welded in side and outside. the flanged end making surface shall be smooth including welding of 04 strip of 5 mm thick 25 mm wide and 50 mm long covering pipe and flanged, both end flanged having 08 nos predrilled hole not less than 16 mm including rubber gasket, nut bolts and washer, pipe should be duly painted with anti corrosive paint complete all as specified and directed. 22 supply, fixing, jointing and testing of cast iron non return valve 100 mm dia flanged ends as per is 5312 ( isi marked ) complete with washer nuts / bolts and rubber gasket complete all as specified and directed. 23 supply, fixing, jointing and testingof cast iron sluice valve 100 mm class i ( isi marked ) pn 1 typelatest is 14846 2000 flanged ends, drilled having stainless steelspindle with cast iron wheel head at top complete with nuts, bolts, washer and rubber gasket etccompleteall as specified and directed. 24 supply, installation, commissioning and testing submersible pumping setmulti stage electric driven of 10 hp capacityat operating head range 10 40 mtr head, directly coupled with electric motor, ac 3 phase, 415 volts, 50 hz, 2900 rpm with copper wound water proof winding complete with flange adoptor suitable for connection with 100 mm dia flanged column pipe and one set of essential tool with price list, literature as recommended by manufacture complete complete all as directed. 25 s&f submersible pump controller in sheet enclosure type mu g20 fully autimaticstar delta starterfor threephase motor 415 volts, 50 hz, 3 phase, 15 hp, 9 14 amps relay range all as specifiedmake : l&t cat part no. :ss95984coaoor equivalent 26 s&f in replacement of pvc insulated flat copper submersible cable heavy duty 16 sqmm 3 core 1100 volt grade of the following size complete all as specified and directed. make havells / plaza / finolex 27 supply and fix high pressure single head adjustable chlorine dosing system including frp pressure dosing tank of capacity 100 ltrs consisting of water inlet line, outlet with y strainer, drian, overflow, conical bottom for sludge deposition , pot hole with cover, level gauage with agitation motor 120 watts 960 rpm, single phase flange mounted motor with plastic shaft and impeller connected to frp service dosing tank of capaicty 100 lts consisting of water inlet line, dozing injector 230v, 50hz including on / off switch and stokes / minute of max 135 min. 15 with motor, discharge pressure 10kg / sqcm, high flow rate of 0 25 lph including drain, overflow level gauge, inspection port, agitator motor 120 watts 960 rpm single phase flange mounted with plastich shaft and impeller including mounting lid, complete all as directed. make: aquafit or equivalant 28 supply & laying in trenches ductile iron ( di ) pipe of size 100 mm bore dia with spigot and socketed ends centrifugally cast class k 7 in any length laid in trenches including di fittings and jointing materails complete all as specified and directed. 29 m&l for 100 mm bore cast iron ( di ) fittings such as bends ( any type, radius and angle ) tapers any type, ( straight, bend, increasing, decreasing or double socket etc ) tee pieces single branch, “y” junction, double branch, cross ( all sockets or socket and spigot ) collars, caps and plugs complete all as specified and directed. 30 supply and lay steel water tubing gi medium grade isi marked with all fittings laid in trenches or fixed to wall etc complete for the following sizes: make: jindal / prakash / swastik note : excavation and earth work will be measured and paid separately. 31 ( a ) 40 mm dia bore 32 ( b ) 25 mm dia bore 33 s&f gun metal gate valve isi marked with iron wheel head screwed both ends for iron pipes and fixed for the following sizes including taking down of unserviceable gate valves. make : zoloto / seico / jindal / upadhaya / venus 34 ( a ) 40 mm bore 35 ( b ) 25 mm bore 36 supply, install, testing and commissioning of busbar chamber of size not less than 60cm x 60cm x 25cm for 3 phase, 415 volts ac, outdoor type, cubical compartmentalised type, weather, vermin and water proof, fabricated out of 2 mm thick crca sheet powder coated front door openable with locking arrangemen and iron angleframe bottom of the panel board including 100 amps mccb , rated copper bus bar, phase indicator , 15 amps switch socket combined , grouted using pcc foundation 1:2:4 type c1 with 20 mm graded stone aggregate, thimbling and cable entry boxes with cable gland including painting with two coat of powder coated painted over a coat of red oxide primer complele all as specifed and directed. 37 m&l for earthing complete with galvanized steel earth plate 600x600x6mm thick buried directly in ground ( earth ) pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level connected to galvanised iron strip 25x4mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel besides welding at all joints as shown in drawings and including excavation and earth work, gi pipe light grade 40mm bore for protection of gi strip from earth electrode to and including the earth test point of galvanised iron / steel of size 75mm x 75mm x 25mm, supplying and laying charcoal stone aggregate ) chamber and mild steel angle iron frame 40x40x3mm and rcc cover 40mm thick ( 1:2:4 ) type b 1 using 20mm graded crushed stone aggregate reinforced with 8mm dia tmt bars @ 75mm o / o both ways with mild steel handle 12mm dia, pgi funnel with wire mesh, 20 mm dia gi pipe light grade for watering all as shownin electrical plate no.3 of mes ssr part 1 38 supply, laying and testing cable xlpe insulated , screened, pvc bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty ) 1100 volts grade with stranded aluminium conductor of size 25 sq mm 4 core all as specified. 39 m&l for boring of holes of 200 mm dia under the road / hard standing by horizontal boring method 2 mtr below the surface for fixing requiste 2 nos. all equipments & machinery required to carry out the work will be provided by the contractor ( if due to any obstruction during boring, reboring has to be done the same will be done by the contractor at his own cost the rates deem to cover the same ) complete all as specified and directed. 40 supply and laying sub class b bricks ( old size ) laid flat in trenches as cable covers all as specified and directed 41 excavation in trenches not exc 1.5 m wide and not exc1.5 m in depth and getting out in soft / loose soil as in foundation all as required and directed 42 m&l for returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as directed. 43 removal excavated material ( soil ) not exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as directed. 44 m&l for cement concrete 1:2:4 type b 2 ( using 40mm graded stone agg ) 100 mm thick as in floor and finish concrete surface even and smooth without using extra cost, complete all as specified. 45 m&l for cement concrete 1:4:8 type d 2 ( using 40mm graded stone agg ) 100 mm thick as in floor, complete all as specified. 46 m&l for rcc ( m 25 design mix ) ( 20mm graded stone aggregate ) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc basement slabs, under reamed piles and mass concreate etc complete all as specified and directed. 47 m&l for rcc ( m 25 design mix ) ( 20mm graded stone aggregate ) as in columns, pillars, posts and struts etc complete all as specified and directed. 48 m&l for form work to sides of concreate foundations, footings, bases of columns, raft and raft beams, sides and soffits ( if any ) of foundation and plinth beams, and similar works vertical or to batter on fair finished surfaces foundation 49 m&l for form work to sides of columns, pillars, posts, struts, piers and stanchions on fair finished surfaces 50 s&f for 10 dia and over mild steel tmt reinforcement bars and spacers cut to length, bent to shape required including cranking, bending, blinding with and including mild steel wire ( annealed ) not less than 0.9 mm dia and necessary welding to reinforcement complete all as specified and directed. 51 s&f for 5 dia and over upto including 10 mm dia mild steel tmt reinforcement bars as in stirrups, spacers and blinders etc complete all as specified and directed. 52 m&l for rendering 10 mm thick in cement mortar ( 1:4 ) on fair faces or brick work or concrete surfaces, finished even and smooth without using extra cement and mixed with water proofing compound @ 3% by weight of cement. ( note: wpc will be measured and paid seperately ) 53 m&l for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer etc complete all as specified. 54 s&f roof trusses ( framed ) , trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing ( beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc complete all as specified and directed. 55 m&l for valve pit chamber of size 1050mm x 1050mm x 1050mm ( internal dimention ) complete including excavation and earth work, pcc 1:4:8, type d 2 using 40mm graded stone aggregate, brick work in cement mortar 1:6, plastering in cement mortar 1:4 ( internally ) and including 3mm thick mild steel sheet cover and painting with two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 56 demolition of cement concrete ( un reinforced ) in ground floors and pavings not exceeding 15cm thickness ( below and above ground level ) and removing the unserviceable materials to a distance not exceeding 100m all as specified and as directed. 57 m & l for pcc 1:2:4 type b2 using 40 mm graded stone aggregate as in sub base / mass concrete complete all as specified and directed. 58 m & l for 20 to 25 mm thick machine cut kota stone slab flooring, landing, steps and plateformover and including 20mm thick screed bed in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing andgrinding and polishingto achive mirror finish complete all as specified and directed. 59 m & lfor 20 to 25 mm thick machine cut kota stone slab on vertical surfaces such as skirting, risers of step, dado etcover and including 10mm thick bearing plaster in cement mortar 1:3, laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and granite polishing complete all as specified and directed. 60 s&f framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or othercovering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) andhanging; also fastening and fixing complete 61 m&lfor pcc ( 1:2:4 ) type b 1using20 mm gradedstone aggregates as in filling on holes in walls, bed block for inserting hold fast and copingincluding necessary form workcomplete all as specified and directed. { the rate is deemed to be inclusive of form work } 62 excavation over area, n exc 1.50 mtr deep and getting out in soft loose soil complete all as specified and directed 63 removing excavated soil exc 1.50 km but n. exc 5 km and deposited wherever directed 64 m&l for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified as directed. 65 m&l for pcc 1:2:4 type b 2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified as directed. 66 m&l for pcc 75mm thick type c 1 , 1:3:6 using 20mm graded stone aggregate as in plinth protection complete all specifiedas directed. 67 supply onlyglass dividing strips 38 mm wide fixed in floorcomplete all as specified and directed 68 demolition of brickwork or stone boulder masonry, built in cement mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles all as specified and as directed. 69 m&l for brick work with sub class b modular brick straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6 complete. 70 taking down cement plaster on brick or stone walls, etc, incl raking out joints, hacking for key, scrubbing down with water, etc & prepare to receive new plaster complete all as specified and directed 71 m&l for 15mm thick rendering in cm 1:3 on surfaces of brick, concrete wall, chajja surface finished even and smooth using extra cement with 2% wpc by weight of cement, appling two coat of polymer modified and cementitious, elastomemric waterproofing coating 1mm thick shall measure and paid seprately under respective item of as supply only complete all as specified and directed 72 supply only liquid water proofing compound 73 m&l for 15mm thick rendering in cm 1:4 on fair faces of brick work, surfaces finished even and faircomplete all as specified and directed 74 m&l for rendering 5 mm thick on concrete surfaces in ceiling , in cement and sand mortar 1:3top surfaces finished even and smooth without using extra cement complete all as specified 75 m&l for preparation of new plastered or unplastered surafces of ceilings and applying three coats of white wash on ceilingincluding washing floors, cleaning glass, joinery, electrical fittings, wiring etc. , of drops and splashes complete all as specified . 76 m&l for preparation of new plastered surface of wall and applying three coats of whitewash on surface of wall incl cornice etc complete all as specified and directed 77 m&l for brooming down plastered or unplastered old decoratedsurface of wall incl cornice etc and applying two coat of whitewash complete all as specified and directed 78 taking down chowkhats or frames n. exc 1.5 sqm each ( without taking off shutter from the frame ) complete. 79 all as per srl item no 72but exc. 1.5 sqm but not exceeding 4 sqm each complete. 80 s & f factory made steel window with side hung shutter including box type hinges with steel handle, steel peg stay, hold fast, complete with glazing bar, dovetailed or welded complete. 81 s & ffactory made steel window with side hung shutter including box type hinges with steel handle, steel peg stay, hold fast complete with ms flat for fixing wire mesh, dovetailed or welded complete . 82 supply only 3 mm thick plain sheet glass / pin headedfigured glass ordinary quality and glazing with oil putty or wooden beads / steel frame in square area n. exc. 0.5 sqm in each pane complete . note : fixing only rate is included in window / door shutter items considered therein 83 supply & fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire stapplescomplete all as specified and directed 84 s & f 125x60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed 85 s&f flush shutters 30mm thick, solid core construction, with block board core & plywood face panels, commercial type on both sides complete all as specified and directed. 86 s & f 35 mm thick of first class hardwood glazed and skeleton shutters, open rebated and prepare to receive glass, gauge, etc., ( with sash bars ) size of members of shutters as specified in ssr part i section 8 clause 8.20 ( a ) supplied and fitted to chowkats complete all as specified and directed. 87 s&f ms flat iron as in hold fast etc and similar work incuding making shape, drilling holes etc, confriming to fe 290 ged e 165 88 m&l for pcc ( 1:3:6 ) type c1 ( using 20mm graded stone aggregate ) as in bed plate for fixing holdfast etc all as specified and directed. 89 s&f aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with beading to wooden frames all as specified and as directed. 90 s&f aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with beading to wooden frames as in repairs all as specified and as directed. 91 s&f aluminium anodised barrel tower bolts of extruded section of length of bolt 200mm all as specified and as directed. 92 supply only butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type b 21 of size 100mm all as specified and as directed. 93 s&f aluminium handles, cast type, anodised of size 100mm all as specified and as directed. 94 s&f 300 mm length aluminium alloy, anodised, sliding door bolts with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed of length of bolt 300mmall as specified and as directed. 95 m&l for preparation of old painted surfaces of wood and wood based materials of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enammel paint. 96 m&l for preparation of old painted steel surfaces and applying one coat of steel painting complete all as specified and directed. 97 m&l for preparation of new steel surfaces and applying two coat of steel paint including primer on steel surfaces complete all as specified and directed. 98 m&l for surface of any discription not otherwise describedover 10 cm width or girth on new untreated surface with two coats of synthetic enammelled painting over one coat pink primer on wooden surface complete all as spd & directed. 99 s&f in repair rubber bead for wooden door 100 dismantling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified and directed 101 s&f pre painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of an colour having tensil strength of 550 mpa as in roof covering to wall fixed with self tapping screws as specified. 102 taking down carefully aluminium battenpoint, wiring for light / fan / socket / bell or power point including. all fittings i.e. switch, sockets, ceiling rose, regulators, batten holders, etc. complete and making good disturbed surfaces of wall / floor to match with the surroundings of wall / ceiling / floor etc including taking down old light fittings. note : ( i ) contractors quoted rate of this item deemed inclusive of unscrewing of the serviceable fittings and fixture as directed and deposit in mes store yard. ( ii ) quoted rate also deem to be included cost of cutting chases for taking out concealed conduit and nitch for terminal box. ( iii ) decision of ge shall be final and binding in respect of serviceability of fittings / fixture. 103 m & l for point wiring complete with 1.5 sqmm single core pvc insulated frls cable 1100 volts grade with multi stranded copper conductor drawn through new pvc concealed conduit medium grade, isi markedand including provision of 1.5 sqmm pvc insulated copper cable frls as earth continuty, fabricated branded modular metal flush box duly make embossed, concealed in walls with suitable modular inner and outer plate for housing switches , socket outlet and fan regulators etc, complete all as specified and as directed for the followings: 104 ( a ) one light / fan / bellpoint controlled by one switch single pole one way 105 ( b ) all as per item no 97 here in before butone3 pin 6 amp switch socket out let independent . 106 ( c ) all as per item no 97 here inbefore but one 3 pin 5 amps socket outlet on the same board with other switch complete . 107 all as per item no 97 here in before but using 02 nos. 4.0 sq mm size for main cable and 01 no.4.0 sq mm size as earth conductor for one 16 amp switch socket outlet on independent board. 108 supply and fix switch modular flush 6a single pole one way isi marked 109 supply and fix modular sockets 6 amp 2 in 1 2 / 3 pin combined all as specified and directed. 110 supply and fix switch modular flush type 15 / 16 amp single pole one way 240 volt one module isi marked 111 supply and fix modular sockets 16amp 2 in 1 3 / 5pin combined all as specified and directed. 112 supply and fix ceiling rose surface bakelite 60x25mm three terminal 113 s&f led batten luminaire surface mounted, 4 feet system wattage of 20 watts, system lumen efficiency >90 lumen / watt, 6500kandincluding connectingfrom ceiling rose to fitting completeallas specified and directed. 114 supply and fix in replcementflood light 30 watt 240 volt 50 htz 3000 / 6500k 120 lumen / wattip 65complete all as spd and directed. 115 supply & fix mcb db spn 8 way, double door, ip 43, ik 09, isolated neutral bar and fixed flush to wall and suitable for universal mounting completeall as specified and directed. 116 supply and fix mcb, single pole and neutral, 230 volts, 32 to 40 amp rating, c series fixed in dbs catered here in before. make legrand / hager / siemense 117 supply and fix mcb sp 6 32 amps 240 volts 10 ka 50 hz c curve complete all as specified and directed by engineer in charge 118 supply and fix wall mounted fan 400mm size, 230 volts , 50 hz 1420 rpm with 90 degree oscillation and having speed control by pull cord system complete all as specified and directed. 119 m&l for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick, buried directly in ground ( earth pit not less than 2.25 metres deep below ground level ) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron wire 4mm dia asearth lead wire by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate no. 3, mes ssr part i 2009 with 15 mm dia medium grade gi pipe as a protection to earthing lead and 20 mm dia medium grade gi pipe for watering purpose including excavation & earth work in any type of soil, funnel, wire mesh, rcc pit with cover, cast iron frame complete and connected to earthing test point all as specified or indicated including testing on completion. notes ( i ) the concrete pit shall be pcc ( 1:3:6 ) type c 1, 40mm thick precast cover slab of rcc with suitable mild steel handle in lieu of cast iron cover shown in electrical plate no 3 of mes ssr part i ( ii ) pcc pit shall be provide at least 500 mm away from the earth pit and not on just on the eath pit and extra cost of additional length of water pipes and fittings junction etc shall be deemed to be included in the rate. ( iii ) item includes the cost of 7.5 metre earth lead wire andgi pipe for protection of earth wire. any varriation in quantity shall be adjusted. 120 supply, laying, jointing & testing of underground lt cables xlpe insulated, pvc sheathed, aluminium conductors, multistranded, armoured heavy duty 1100 volt grade cross sectional area 16 sqmm 2 core laid in trenches / ducts / along poles / through pipe under road etc with new aluminium lugs....

Central Reserve Police Force - Uttar Pradesh

35459926 tender for re carpetying of internal road at gc, crpf, amethi ( u.p ) providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level : 1:5:10 ( 1 cement : 5 coarse sand ( zone iii ) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources ) 2 providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources ) . 3 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo mechanically treated bars of grade fe 500d or more. 4 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in foundation and plinth in: cement mortar 1:6 ( 1 cement : 6 coarse sand ) . 5 steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 6 12 mm cement plaster of mix : 1:6 ( 1 cement: 6 coarse sand ) 7 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 ( 1 cement: 6 coarse sand ) 8 neat cement punning. 9 finishing with epoxy paint ( two or more coats ) at all locations prepared and applied as per manufacturers specifications including appropriate priming coat, preparation of surface, etc. complete. on concrete work 10 disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by engineer in charge, beyond 50 m initial lead, for all leads including all lifts involved. 11 providing and applying tack coat using hot straight run bitumen of grade vg 10, including heating the bitumen, spraying the bitumen.with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications : on w.b.m. @ 0.75 kg / sqm 12 providing and applying tack coat using hot straight run bitumen of grade vg 10, including heating the bitumen, spraying the bitumen.with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications :on bituminous surface @ 0.50 kg / sqm 13 cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size ) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete. 14 providing and fixing glow studs of size 100x20 mm made of heavy duty body shall be moulded asa ( acrylic styrene acryloretrite ) or hip ( high impact polystyrene ) or abs having electronically welded micro prismatic lens with abrasion resistant coating as approved by engineer in charge. the glow stud shall support a load of 13635 kg tested in accordance with astm d4280. the slope of retro reflective surface shall be 35 ( + / 5 ) degress to base .the reflective panels on both sides with at least 12 cm of reflective area up each side. the luminance intensity should be as per the specification and shall be tested as described in astm i: 809 as recommended in bs: 873 part 4 : 1973. the studs shall be fixed to the road surface using the adhesive conforming to is, as per procedure recommended by the manufacturer complete and as per direction of engineer in charge. 15 providing and laying bituminous macadam using crushed stone aggregates of specified grading premixed with bituminous binder, transported to site by tippers, laid over a previously prepared surface with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specificatons and directions of engineer in charge. 50 to 100 mm average compacted thickness with bitumen of grade vg 30 @ 3.50% ( percentage by weight of total mix ) prepared in drum type hot mix plant of 60 90 tph capacity. 16 providing and laying bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of engineer in charge. 40 / 50 mm compacted thickness with bitumen of grade vg 30 @ 5.5% ( percentage by weight of total mix ) and lime filler @ 3% ( percentage by weight of aggregate ) prepared in drum type hot mix plant of 60 90 tph capacity. 17 manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type iv of astm d 4956 01 in blue and silver white or other colour combination including subject matter, message ( bilingual ) , symbols and borders etc. as per irc ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class 2 of astm d 4956 01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c / c to back support frame of m.s. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 nos. m.s. angles of size 35x35x5 mm to a vertical post made up to m.s. tee section ismt 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing m.s. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer ( vertical ms tee support to be painted in black and white colours ) .backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of engineer in charge. cautionary / warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm 18 providing and applying 2.5 mm thick road marking strips ( retroreflective ) of specified shade / colour using hot thermoplastic material by fully / semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, t&p, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of engineer in charge and accordance with applicable specifications. 19 providing and fixing post delineators made of abs round body fitted with 2 nos 100 mm dia high reflective reflectors and mounted on ms pipe of 65 mm dia duly powder coated anti rust and anti theft steel to be installed as per direction of engineer in charge. 20 providing and laying at or near ground level factory made kerb stone of m 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 ( 1 cement: 3 coarse sand ) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5mm ) , including making drainage opening wherever required complete etc. as per direction of engineer in charge ( length of finished kerb edging shall be measured for payment ) . ( precast c.c. kerb stone shall be approved by engineer in charge ) . 21 construction of granular sub base by providing close graded material conforming to specifications, mixing in a mechanical mix plant atomc, carriage of mixed material by tippers to work site, for all ed thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of engineer in charge. with material conforming to grade ii ( size range 53 mm to 0.075 mm ) having cbr value 25 22 providing and laying factory made chamfered edge cement concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size / shape, made by table vibratory method using pu mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of engineer in charge. 60mm thick cement concrete paver block of m 35 grade with approved colour, design & pattern. 23 taking out of existing r.c.c slab cover ( 75 to 100 mm thick ) from the existing drain and staking the same near the site, disposal of unserviceable materials within 50 meters lead including refixing with cement mortar 1:3 after correction of slope of existing drain etc, all complete as per direction of engineer in charge ( item for correction of the slope shall be paid separately ) 24 providing and fixing sfrc manhole covers with frame of size 600 mm x 1000 mm l.d. grade....

Uttar Pradesh Jal Nigam - Uttar Pradesh

34773422 construction of 1000 capacity auditorium between mathura and vrindavan distt mathura material pcr rate for construction of 1000 capacity auditorium between mathura and vrindavan distt mathura , supply ofindian type w.c. panparryware/ hindware/ seabird/ orient (coral). white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests , supply of flushing cistern p.v.c. 10 lts capacity (low level) (white) (with fittings, accessories and flush pipe) pan size 580 mmwith manually controlled device (handle lever) conforming to is:7231 , supply of 100 mm s.c.i. trap with vent heel , supply of vitreous china flat back wash basin 550x400 mm with c.i. bracket for wash basin and sinks, c.p. brass waste 32 mm , supply of 15 mm c.p. brass tap , supply of semi rigid pvc waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm i/c pvc waste fittings , supply of semi rigid pvc waste pipe for sink and wash basin 40 mm dia with length not less than 700 mm i/c pvc waste fittings , supply of mirror of superior make glass 60x45 cm, hard board 6 mm thick, 600x450 mm wooden cleats, sh : cladding work (4 no), chromium plated brass screws 25 mm (4 no) , supply of stainless steel kitchen sink with drain board bowl depth 250 mm. 510x1040 mm bowl depth 250 mm, incl. c.i. bracket for wash basin and sinks , supply of unplasticised p.v.c. connection pipe with brass union 45 cm long 15 mm bore , supply of c.p. brass bibcock 15 mm , supply of c.p. brass long body bibcock 15 mm , supply of c.p. brass angle valve 15 mm , supply of shower rose c.p. brass for 15 to 20 mm inlet 150 mm dia , supply of c.p. brass stop cock (concealed) 15 mm , supply of vitreous china pedestal type water closet, incl. black plastic seat (solid) with lid c.p. brass hinges and rubber buffers , supply of white vitreous china clay half stall urinal flat back 580x380x350 mm or angle back 450x375x350 mm with waste fittings as per is : 2556 , supply of p.v.c. automatic flushing cistern 5 lts capacity , supply of flush pipe with union spreaders and clamps all in c.p. brass for single stall , supply of c.i. trap for standard urinal with vent arm with operating and other couplings in c.p.brass: 50 mm dia , supply of table rubbed polished stone 18mm thick (75x50cm) granite stone 18mm thick , supply of p.v.c. automatic flushing cistern 10 lts capacity , supply of flush pipe with union spreaders and clamps all in c.p. brass for range of three stall , supply of c.i. trap for standard urinal with vent arm with operating and other couplings in c.p.brass: 80 mm dia , supply of flush pipe with union spreaders and clamps all in c.p. brass for double stall , supply of gunmetal non return valve horizontal (screwed end) 32 mm dia , supply of u pvc pipes (working pressure 6 kg / sqcm) single socketed pipe 110 mm dia. , supply of u pvc pipes (working pressure 6 kg / sqcm.) rubber (seal) ring 110 mm dia. , supply of upvc bend 87.5° 110 mm bend , supply of upvc bend 90° 110 mm bend(elbow) , supply of upvc plain shoe 110 mm bend , supply of c.i. grating 150 mm dia. (weighing not less than 440 gm) , supply of stone ware spouts 100 mm dia 60 cm long , supply of pvc spouts 160 mm dia 60 cm long , supply of upvc pipe clip 110 mm bend , supply of upvc pipe clip 90 mm end cap , supply of upvc pipe clip 110 mm end cap , supply of upvc pipe clip 150 mm end cap , supply of plug , supply of upvc pipe clip 75 mm bend , supply of and fixing 15cm wide 45cm over all semi circular plain g.s. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc. including making necessary connections with rain water pipes complete. 0.80mm thick with zinc coating not less than 275 gm/m2 galvanised steel plain sheets (3.5 kg); flats upto 10 mm in thickness (0.8 kg); galvanised steel bolts & nuts 6 mm dia and 25 mmlong round head with slots ; galvanised steel bolts & nuts 10 mm dia and 125 mm long round head with slots ; g.i. plain washer thin ; bitumen washer , supply of chlorinated polyvinyl chloride (cpvc) pipe 20 mm outer dia.; including fittings & clamps etc. , supply of chlorinated polyvinyl chloride (cpvc) pipe 25 mm outer dia.; including fittings & clamps etc. , supply of chlorinated polyvinyl chloride (cpvc) pipe 32 mm outer dia.;including fittings & clamps etc. , supply of chlorinated polyvinyl chloride (cpvc) pipe 40 mm outer dia.;including fittings & clamps etc. , supply of g.i. pipes 20 mm dia.;including fittings & clamps etc. , supply of g.i. pipes 25 mm dia.;including fittings & clamps etc. , supply of g.i. pipes 32 mm dia.;including fittings & clamps etc. , supply of g.i. pipes 40 mm dia.;including fittings & clamps etc. , supply of g.i. pipes 50 mm dia.;including fittings & clamps etc. , supply of g.i. pipes 65 mm dia.;including fittings & clamps etc. , supply of brass stop cock 20 mm dia , supply of brass full way valve with c.i. wheel (screwed end) 25 mm dia , supply of brass full way valve with c.i. wheel (screwed end) 32 mm dia , supply of brass full way valve with c.i. wheel (screwed end) 40 mm dia , supply of brass full way valve with c.i. wheel (screwed end) 50 mm dia , supply of brass full way valve with c.i. wheel (screwed end) 65 mm dia , supply of g.i. union 20 mm nominal bore , supply of g.i. union 25 mm nominal bore , supply of g.i. union 32 mm nominal bore , supply of g.i. union 40 mm nominal bore , supply of g.i. union 50 mm nominal bore , supply of g.i. union 65 mm nominal bore , supply of polyethylene water storage tank with cover and suitable locking arrangement [sintex, electroplast, star, lotus of isi mark]. the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply of stoneware pipes grade a 100 mm dia with spun yarn or plain gaskin , supply of s.w. gully trap p type 150x100 mm , supply of c.i. grating 150x150 mm , supply of c.i. cover and frame 300x300 mm inside , supply of pvc soil, waste and vent single socketed pipe : 110mm dia , supply of pvc soil, waste and vent single socketed pipe : 90 mm dia , supply of g.i. pipes 80 mm dia; including supply of specials for pressure pipe , supply of brass full way valve with c.i. wheel (screwed end) 80 mm dia , supply of r.c.c. pipes np2 class 150 mm dia metre , supply of r.c.c. collars np2 class 150 mm dia , supply of r.c.c. pipes np2 class 250 mm dia , supply of r.c.c. collars np2 class 250 mm dia , p trap type floor trap 110 x 110mm , pvc moulded fittings/accessories for unplasticised rigid pvc pipes 110mm bend , pvc moulded fittings/accessories for unplasticised rigid pvc pipes 90 mm bend , pvc moulded fittings/accessories for unplasticised rigid pvc pipes 110mm coupler . , pvc moulded fittings/accessories for unplasticised rigid pvc pipes 90mm couplern. , pvc moulded fittings/accessories for unplasticised rigid pvc pipes single tee with door 90x90x90mm. , pvc moulded fittings/accessories for unplasticised rigid pvc pipes single tee with door 110x110x110mm. , rigid pvc rain water pipes 160mm dia. conforming to is: 13592 type a including jointing with seal ring conforming to is: 5382 , 60x2cm c.p. brass towelrail complete with c.p. brass brackets fixed to wooden cleats with c.p. brass screw.parryware c9948 or equivalent , cp soap tray fixed to the wallwith pvc rubber plug with cp brass screws , jaquaror equivalent make c.p. brass bottle trap. , c.p. brass ablution health faucet assembly with 1.2 m long braided pvc hose with mounting bracket fixed on wall complete.[for ewc] , c.p. brass two way angle valve for ewc points & for fixing ablution health fauct of approved quality conforming to is:8931. 15 mm nominal bore , pvcinlet fitting with 2 inlets 80 mm size fabricated from 110 mm dia pvc pipes(approx. length=150mm to 300mm) and fixed to pvc trap with joint and set in cement concrete as per standard drawingcomplete. , 110mm terminal guard. , 90mm terminal guard. , 110 mm clean out plug , r.c.c. inspection chamber 60x60x75 cm , supply of orange colour safety footrests of minimum 6 mm thick plastic encapsulated as per is:10910 on 12 mm dia steel bar conforming to is:1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm thread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing , supply of m.s. foot rest including fixing with 20x20x10 cm as per standard design with 20x20mm sq bars. , c.i. tee at the inlet and outlet of septic tank. , 75mm dia vent pipes. , 75mm dia cast iron terminal guard. , supply of precast rcc manhole cover and frame of required shape and approved quality. m.d. 10 circular shape 500mm internal diameter , supply of precast rcc manhole cover and frame of required shape and approved quality. m.d. 2.5 circular shape 450mm internal diameter , supply, testing & commissioning ofof singal headed hydrant landing valve comprising of 80 mm dia flanged bend 63 mm dia, with cap and chain conforming to is:5290(make : newage/minimax/safex/firex) the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning ofof rrl hose pipe 63 mm dia × 15 mtr. long with gm coupling conforming to is : 636(make newage/jayshree/crc) the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning ofof short branch pipe as per is:903(make : newage/safex/firex) the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning ofof first aid hose reel drum with 20 mm dia, 30 mtr long rubber pipe shut of nozzle conforming to is:884(newage/firex/isi marked) the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning ofof hose cabinet box of 18 swg m.s.sheet with glass to accommodate hosr reel drum with ruber pipe with nozzle. 2 nos. rrl hose and 1 no. branch pipe with nozzle. the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning ofof fire brigade inlet 2 way(make: newage/minimax/geetech). the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning of m.s. 100 mm dia. pipe c class heavy as per is:1239 including cutting, jointing and welding etc., and providing suitable flanges alongwith necessary fittings like bends. tees, reducers etc. and coating of primer and p.o. red paint. make : qst/jindal gzb. the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning ofof 100 mm dia. sluice valve complete with all respect. the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning ofof 100 mm dia. non return valve ci dual plate with nut, bolt and washers etc. as per is: 5312 (make : sir/aarko/lp/kalpna/isi marked). the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning of electrical motor driven fire pump suitable for automatic operation consisting of following : (terrace pump)(make : kirloskar/mather+platt) (a) horozontally mounted, split casing, centrifugal fire pump complete for delivery of under mentioned discharge against desired mentioned head so as to ensure a minimum pressure of 30 meter at the highest and farthest outlet at the specified flow cmplete with necessary strainers, pressure gauge including bypass arrangement for periodic testing of the working of the pumpset with required length and size of medium class gi pipe and control valves for proper completion of work.the pump shall be capable of giving 150% of rated discharge at head not less than 65% of rated head.the pump shall be provided with mechanical seals. the impeller shall be enclosed type and accurately blanced dynamically.the pump casing shall be of cast iron, impeller shall be of bronze and shaft shall be of stainless steel. (b) squirrel cage, tefc induction motor suitable for 415 v, 3 phase having ip 55 protection and class b insulation for the above pump and flexible coupling with the pump.the motor shall b rated for continuous duty and shall have hp rating necessary to drive th pump at 150% of its rated discharge at 65% of rated head. (c) common bed plate of fabricated mild steel channel or cast iron type. (d) suitable cement concrete pump foundation and vibration clamping arrangement as required with foundation bolts, anti vibration pads, washers etc. (e) pressure switch for automatic operation of motor including necessary wiring upto control panel. (f) electrical control panel with starter, 3 pole motor protection category current limiting type mccb, indicating light, ammeter, voltmeter, selector switches, cts protective fuses, single phasing protection, dry suction cut off etc as requrd as per standard details. discharge : 450 liter per minutehead : 35 meter the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning ofof air cushion tank suitable capacity made out of 6 mm thick ms sheet 200 x 1200 × 8 mtr. long complete in all respects. the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply of fire man axe , supply, testing & commissioning of fire extinguisher (firiecon/lifegurd/firefit/excell) abc type 6 kg. the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning of fire extinguisher (firiecon/lifegurd/firefit/excell) co2 type 4.5 kg. the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning ofof singal headed hydrant landing valve comprising of 80 mm dia flanged bend 63 mm dia, with cap and chain conforming to is:5290(make : newage/minimax/safex/firex) the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning ofof rrl hose pipe 63 mm dia × 15 mtr. long with gm coupling conforming to is : 636(make newage/jayshree/crc) the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning ofof short branch pipe as per is:903(make : newage/safex/firex) the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning ofof first aid hose reel drum with 20 mm dia, 30 mtr long rubber pipe shut of nozzle conforming to is:884(newage/firex/isi marked) the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning of networkable logic driven analogue addressable main fire alarm control and indicating panel. the panel shall be coupled to the pa system complete in all respect. 4 loop. panel the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning of of analogue addressable photo smoke detectors based with led shall be visible from 360deg, complete as required. (make:/ gst/morley) the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning offault isolator (gst/morley) the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning of monitor module. (gst/morley) the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning ofof manual call point with mounting box complete as required. the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply installation, testing and commissioning of electronic hooter 6 watt output tac approved with a range of 25 30 mtr. the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply of copper conductor armoured cable 2 x 1.5 sq. mm , supply, testing & commissioning of response indicator with dual led. the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply of 25 mm steel conduit alongwith the accessories in recess including painting of surface conduit. , supply, testing & commissioning of dust proof type push button to initiate audio visual alarm with a breakable glass cover as per specification complete with small steel hammer attached with steel chains as required (mannual call points) the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning of fire alarm hooter/hooter cum speaker having an audio range of 25 meter in custom built cabinet. the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning of4 zone main control panel with window type annunciation to indicate fire and fault, lead lamps for visual indication, audio alarm unit, push button for acknowledge, test, reset complete with power supply. the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply of material for wiring with 2x1.5 sqmm solid pvc insulated copper conductor 100 volt grade wires in existing concealed conduit including terminations, all material etc complete , supply, testing & commissioning ofof exit light the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning of ionization type smoke detector complete with base. the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply, testing & commissioning ofwilo make vertical in line pumping setcomplete. the rate shall include the cost of electrical panel and piping work complete domestic water supply pumps : capacity/flow rate 300 lpm head 35 m location pump room at ugt the mode of payment for supply shall be; 90% payment after procurement and safe delivery and proper storage of material at site, 5% payment after successful testing and balance 5% payment after successful commissioning. , supply ofgranular sub base by providing close graded material conforming to specifications, mixing in a mechanical mix plant at omc, carriage of mixed material by tippers to work site, for all leads & lifts , supply of baroda/ udaipur green marble (table rubbed and polished) 18 mm thick , supply of ms tubular hollow pipe for heavy sections used for larger span trusses including nut bolts, cleat plates angles and other hardwares etc. required for fabrication and fixing with two coat of ro primer and two or more coats of synthetic enamal paints.125 mm dia. ms pipe (m) , stainless steel cramps , fastener with threaded dia 12 mm , supply of 35mm thick kota stone for flooring , supply of 25mm thick kota stone for flooring...

Food Corporation Of India - Uttar Pradesh

34136930 annual repair and maintenance of work at fsd naini dismantling doors, windows and clerestory windows ( steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :of area 3 sq. metres and below 2 dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. 3 demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge.in cement mortar 4 removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m ( stacks of cleaned bricks shall be measured ) : from brick work in cement mortar 5 dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: asbestos cement sheet 6 removing dry or oil bound distemper, water proofing cement paintand the like by scrapping, sand papering and preparing the surfacesmooth including necessary repairs to scratches etc. complete. 7 providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete. 8 wall painting with premium acrylic emulsion paint of interior grade, having voc ( volatile organic compound ) content less than 50grams / litre of approved brand and manufacture, including applyingadditional coats wherever required to achieve even shade and colour.two coats 9 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 10 white washing with lime to give an even shade : old work ( two or more coats ) 11 finishing walls with acrylic smooth exterior paint of required shade :new work ( two or more coat applied @ 1.67 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm ) 12 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by engineer incharge.all kinds of soil 13 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level :1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources ) 14 providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing andreinforcement all work up to plinth level :1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources 15 centering and shuttering including strutting, propping etc. and removal of form for :foundations, footings, bases of columns, etc. for mass concrete 16 steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 17 supplying and fixing 3 mm thick translucent white acrylic plastic sheet to suit semi corrugated sheet roofing made from thermo setting polyester resin fiber reinforced as per isi 2866 1989 to suit fully corrugated ac sheet roofing overlapping on corrugation and with light transmission not less than 80 % with two diagonal bracing of ms flats 40x6mm including self tapping screws epdm seal and washer complete as per the direction of engineer in charge but excluding the cost of purlins rafters and trusses 18 providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete.fixed to steel windows by welding 19 providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for separately ) : for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber / neoprene gasket required ( fittings shall be paid for separately ) powder coated aluminium ( minimum thickness of powder coating 50 micron ) 20 providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . ( cost of aluminium snap beading shall be paid in basic item ) : with float glass panes of 4.0 mm thickness ( weight not less than 10kg / sqm ) 21 providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including isi marked stainless steel butt hinges with necessary screws 22 providing and fixing bright finished brass door latch with necessary screws etc. complete : 300x16x5 mm 23 providing and fixing bright finished brass tower bolts ( barrel type ) with necessary screws etc. complete : 250x10 mm 24 providing and fixing bright finished brass handles with screws etc. complete:125 mm 25 painting with synthetic enamel paint of approved brand and manufacture to give an even shade :two or more coats on new work 26 providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand / make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing p / s trap, complete in all respect as per directions of engineer in charge. 27 providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white pvc automatic flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps ( all in c.p. brass ) with waste fitting as per is : 2556, c.i. trap with outlet grating and other couplings in c.p. brass, including painting of fittings and cutting and making good the walls and floors wherever required : single half stall urinal with 5 litre p.v.c. automatic flushing cistern 28 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer in charge. 29 providing and fixing counter top wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: white vitreous china wash basin size 500x400 mm with a pair of 15 mm c.p. brass pillar taps. 30 providing and fixing kitchen sink with c.i. brackets, c.p. brass chain with rubber plug, 40 mm c.p. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: white glazed fire clay kitchen sink of size 600x450x 250 mm 31 providing and fixing chlorinated polyvinyl chloride ( cpvc ) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i / c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.concealed work, including cutting chases and making good the walls etc. 15 mm nominal dia pipes 32 providing and fixing cp brass bib cock of approved quality :15 mm nominal bore 33 providing and fixing c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931 15mm nominal bore 34 providing and fixing p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. semi rigid pipe 32 mm dia 35 providing and fixing mirror of superior glass ( of approved quality ) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : rectangular shape 1500x450 mm 36 providing and fixing ptmt grating of approvdquality and colour .circular type 100 mm nominal dia 37 providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand ) , joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.granite stone slab of colour black, cherry / ruby red area of slab upto 0.50 sqm 38 lettering with foame of required colour and shape etc complete over granite / wall as per direction of engineer in charge 39 lettering with brass of required colour and shape etc complete over granite / wall as per direction of engineer in charge 40 reinforced cement concrete work in walls ( any thickness ) , including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing andreinforcement : 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) : 3 graded stone aggregate 20 mm nominal size ) 41 centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers andcantilevers 42 providing and placing on terrace ( at all floor levels ) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 43 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo mechanically treated bars of grade fe 500d or more. 44 centering and shuttering including strutting, propping etc. and removal of form for walls ( any thickness ) including attached pilasters, butteresses, plinth and string courses etc. 45 providing and laying vitrified tiles in floor in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 ( 1 cement: 4 coarse sand ) jointing with grey cement slurry @3.3 kg / sqm including grouting the joints with white cement and matching pigments etc. the tiles must be cut with the zero chipping diamond cutter only . laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. glazed vitrified tiles matt / antiskid finish of size of tile 600 x 600 mm 46 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 47 providing and laying factory made chamfered edge cement concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size / shape, made by table vibratory method using pu mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of engineer in charge. 80 mm thick c.c. paver block of m 30 grade with approved color design and pattern. 48 providing and laying at or near ground level factory made kerb stone of m 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 ( 1 cement: 3 coarse sand ) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5mm ) , including making drainage opening wherever required complete etc. as per direction of engineer in charge ( length of finished kerb edging shall be measured for payment ) . ( precast c.c. kerb stone shall be approved by engineer in charge ) . 49 credit for old dismanteled windows and doors 50 credit for old iron scrap 51 providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources ) . 52 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and accessplatform...

Department Of Skill Development - Uttar Pradesh

30517847 bids are invited for measuring steel tape 5 meter , combination plier insulated 200 mm , screwdriver insulated diamond head 4mmx 150 mm, diamond head , screwdriver insulated 6mmx 150 mm , punch centre 9mm x 150 mm , knife double bladed electrician 100 mm , neon tester 500 v , spanner adjustable drop forged, ss 150 mm & 300mm , blow lamp brass 0.5 ltr , chisel cold 25 mm x 200 mm , chisel firmer with wooden handle 6 mm x 200 mm , grease gun 0.5 ltr. capacity , bradawl bradawl , pully puller with 3 legs 150 mm & 300mm , bearing puller ( inside and outside ) 200 mm , scissors blade, ss 200mm 200mm , scissors blade, ss 150 mm 150 mm , wire cutter and stripper 150 mm , mallet hard wood 0.50 kg , hacksaw frame adjustable 300 mmfixed 150 mm , pliers long nose insulated 150 mm , pliers flat nose insulated 200 mm , pliers round nose insulated 100 mm , tweezers 150 mm , snip straight and bent heavy duty 250 mm , d.e. metric spanner double ended 6 32 mm , plane cutters 50 mm x 200mm , smoothing cutters 50 mm x 200mm , gauge, wire imperial stainlees steel marked in swg & mm wire gauge metric , file flat 200 mm 2nd cut with handle , file half round 200 mm 2nd cut with handle , file round 200 mm 2nd cut with handle , file flat rough 150 mm with handle , file flat bastard 250 mm with handle , file flat smooth 250 mm with handle , file rasp, half round 200 mm bastard with handle , copper bit soldering iron. 0.25 kg , de soldering gun heat proof nozzle, pvc type, 250mm , table vice 100 mm jaw , oil can 250 ml , contactor & auxiliary contacts 3 phase, 415 volt, 25 amp with 2 no , contactor & auxiliary contacts. 3 phase, 415 volt, 32 amp with 2 noand 2 nc , limit switch limit switch, liver operated 2a 500v, 2 contacts , rotary switch 16 a / 440v , relay a. cut out relaysb. reverse currentc. over currentd. under voltage a. 16a, 440vb. 16a, 440vc. 16a, 440vd. 360v 440v , hydrometer hydrometer , portable electric drill machine 0 12 mm capacity 750w, 240v withchuck and key , brake test arrangement with twospring balance rating 0 to 25 kg , laboratory type induction coil 1000 w , out side micrometer 0 25 mm least count 0.01mm , thermometer digital 0° c 150° c , miniature breaker 16 amp , earth plate 60cm x 60cm x 3.15mm copper plate60cm x 60cm x 6mm gi plate , earth electrode primary electrode 2100x28x3.25mm secondary cu strip 20x5mm , mccb 100amps, triple pole , elcb and rccb 25amps, double pole and 25amps, double pole, i?n 30 ma , fuses hrcglassrewire type , rheostat ( sliding type ) 0 25 ohm, 2 amp0 300 ohm, 2 amp0 1 ohm, 10amp , rheostat ( sliding type ) 0 10 ohm, 5 amp 0 10 ohm, 5 amp , capacitors electrolytic ceramic polyester film variabledual run , various electronic components resistors, diode, transistor, ujt, fet, scr, diac, traic, igbt, smalltransformer etc. , various lamps halogen incandescent lamp fluorescent tubehp mercury vapor lamp high pressure sodium lamp low pressure sodium lampled , plug socket piano switchlamp holder 230 v, 5 a , cables:twisted pairnon metallic sheathed cable underground feeder cable ribbon cablemetallic sheathed cable multi conductor cable coaxial cabledirect buried cable 1 mtr each , bus bar with brackets 1 mtr each , rubber mat 2’ x 4’ x 1” , electrician helmet yellow colour , rcc pole with accessories ( ms angle iron, ‘c’ clamp, stay insulator etc. ) and materials 6 mtr , safety belt standard quality , ohm meter; series type & shunt type, portable box type 50 / 2000 ohm analog , digital multi meter dc 200mv 1000v, 0 – 10a & ac200mv 750v , 0 10a, resistance 0 20 mo and3 1 / 2 digit , a.c. voltmeter m.i.analog, portable box type housed in bakelite case multi range 75 v 150v 300v 600v , milli voltmeter centre zero analog, portable box type housed in bakelite case 100 – 0 – 100 mv , ammeter mc analog, portable box type housed in bakelite case 0 500 ma, 0 5 a, 0 25 a , ac ammeter mi, analog, portable box type housed in bakelite case 0 500 ma, 0 5 a, 0 25 a 0 1 a, 0 5 a, 0 25 a , kilo wattmeter analog 0 1.5 3kw, pressure coil rating 240v / 440v, current rating 5a / 10a analoge, portable type housed in bakelite case , digital wattmeter 230 v, 1 kw, 50 hz , a.c. energy meter singlephase, 10a, 240vinduction type singlephase, 10a, 240vinduction type , a.c. energy meter threephase, 15a, 440vinduction type threephase, 15a, 440vinduction type , power factor meter digital 440v, 20a, threephaseportable box type , frequency meter 45 to 55 hz , magnetic flux meter 0 500 tesla , lux meter lux meter lcd read out 0.05 to 7000lumens with battery. , tachometer analog type 10000 rpm analog type 10000 rpm , tachometer digitalphotosensortype 10000rpm , tong tester / clamp meter 0 100 a ( digital type ) , megger analog 500 v , wheat stone bridge with galvanometer and battery wheat stone bridge with galvanometer and battery , single phase variable autotransformer 0 270 v, 10amp ( air cooled ) , phase sequence indicator 3 phase, 415 v , growler 230 v, 50 hz, single phase, adjustable jaws, testing armature with ampere meter and testingprobes. , for a.c motors of 2 to 5 h.p. ac starters: a. resistance type starterb. direct online starterc. star delta starter manuald. star delta starter – semi automatice. star delta starter – fully automaticf. star delta starter soft starterg. auto transformer type , oscilloscope dual trace 20 mhz , function generator 2 to 200 khz, sine, square, triangular220 v, 50 hz, single phase , soldering iron 25 watt, 65 watt and 120 watt, 230 volt , temperature controlled solderingiron 50 watt, 230 volt , discrete component trainer discrete component ( for diode andtransistor circuit ) with regulated power supply +5, 0 5 v, +12 , 0 12 v , linear i.c. trainer linear i.c. trainer with regulated power supply 1.2v to 15v pic socket 16pin and 20 pins with bread board , digital i.c. trainer digital i.c. trainer 7 segment displayand bread board , a. electric induction plate a. 1500 watt, 240v , b. electric kettle b. 1500 watts, 240v , c. electric iron c.automatic 750 w, 240 v , e. a.c. ceiling fan and ac table fan e. 68 watt, 230 v , g. mixture & grinder g. 750 w, 240 v , h. washing machine semi automatic h. 5 kg, , i. motor pump set i. 1 hp, 1 phase, 240 v , oil testing kit oil testing kit 230 v, single phase 50hz 60 va output 0 60 kv variable , inverter with battery 1 kva with 12 v battery input 12 volt dc, output 220 volt ac , voltage stabilizer ac input 150 250 v, 600 vaac output 240 v, 10 a , dc power supply 0 30 v, 5 a , battery charger 0 6 9 12 24 48 v, 30amp , current transformer 415 v, 50hz, ct ratio 25 / 5 a, 5va , potential transformer 415 v, 50hz, pt ratio, 440v / 110v, 10va , solar panel with battery 18 watt , d.c. shunt generator with control panel d.c. shunt generator with control panel, 2.5 kw, 220v &3phase squirrel cage induction motor, 5hp, 440v with control panel & star delta starter , d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker, 2.5 kw, 220v &3phase squirrel cage induction motor, 5hp, 440v, with control panel & star delta starter , shunt motor rating: 5 hp, 440vac generator rating : 3 phase, 4 wire, 3.5 kva, 400 / 230 volts, 0.8 pf, 50cycles motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts andflexible coupling. , ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse with mechanical load. 5 hp, 3 phase, 415 v, 50 hz , synchronous motor with accessories like starter, excitation arrangements. 3 phase, 3 hp, 440v, 50hz, 4 pole , thyristor / igbt controlled d.c. motor drive with tacho generator feedback arrangement 1 hp , thyristor / igbt controlled a.c. motor drive with vvvf control 3 phase, 2 hp , electrical machine trainer – suitable for demonstrating the construction and functioning of different types of dc machines and ac machines ( single phase and three phase ) . should be fitted with friction brake arrangement, dynamo meter, instrument panel and power supplyunit , used dc generators series, shunt and compound type for overhauling practice used dc generators series, shunt and compound type for overhauling practice , pillar electric drill machine motorized 12 20 mm capacity, 1hp, 440v, 3 phase, induction motor with dolstarter, bench type , manual motor coil winding machine with step arbor , ceiling fan coil winding machine 250v, 50 hz, 1 ?, with speed control , primary current injection set 220v, 50 hz, 1 ?, output current 200 a ( min ) with timer , stepper motor with digital controller stepper motor with digital controller , shaded pole motor fractional hp, 240 v, 50 hz total quantity : 1...

Military Engineer Services - Uttar Pradesh

30209371 certain sanctioned work under age br i ge faizabad certain sanctioned work under age br i ge faizabad 1 dismantling floor, hearth or wall tiling including cm bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises , complete all as specified. 2 taking down chowkats or framesnexc1.5 sqm each ( without taking off shutters from the frames ) , complete all as specified. 3 taking down cement plaster from brick walls including raking out joints, hacking for key, scrubbing down with water to receive plaster removal of rubbish off the premises etc., complete all as specified. 4 m&l non skid ceramic coloured tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles and including 15mm thick screed bed in cm 1:6 , complete all as specified. 5 m&l glazed ceramic coloured tiles in vertical surface 350x250x 7 mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to matchwith the shade of tiles and including 10mm thick rendering in cm 1:3 to receive wall tiles , complete all as specified. 6 demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar, complete all as specified. 7 m & l 5mm thick rendering on fair faces of brick work or concrete surface in cm 1:3 as in ceiling to be finished even and smooth with out using extra cement, complete all as specified.. 8 m & l 10mm thick rendering on fair faces of brick work or concrete surface in cm 1:4 to be finished even and smooth withoutusing extra cement , complete all as specified.. 9 cutting chasesin brick walls , pinning in, making good to facings where required and pointing in cm 1 : 3 to ends, or edges of landings steps, cills, and cutting chases for concealed water tubing or conduit wiring etc and making good cutting n exc 10 cm girth , complete all as specified. 10 m&l for form work to sides and soffit of floor or roof beam, beam haunchings, girders, bressummers lintels, cantilevers, shelves including supports, overhangings etc., also splays between floor and beam as in fair finished, complete all as specified. 11 s & ftmt steelbars 6 to 8 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including ms wire annealed not less than 0.9 mm dia , complete all as specified. 12 m & lrcc 1 : 2 : 4 type b1 ( 20 mm graded crushed stone aggregate ) as in slabs supported on walls beam and colums in floors, roofs, landings, deck slabs and shelves and the like , complete all as specified. ( formwork and reinforcement shal be measured and paid separately ) 13 m&lfor 20mm thick machine cut granite stone, in skirting / dado laid over cement screed and jointed with gray cement slurry and pointed white cement with admixture of pigment to match the shade of granite stone including grinding and polishing and including 15mm thick screed bed in cm 1:6 , complete all as specified. 14 rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations , complete all as specified. 15 s&f wash hand basin of size 61x46x15mm and including sensor pillar tap and bottle trap complete all as specified .cat no : 91043 & cat no f240005cp or equivalent as approved by ge / 16 s&f10mm thick frosted toughened glass door swing type with 300 mm wide stainless steel handle andincluding floor spring and locking arrangement and necessary fittings, complete all as specified. 17 s&f ewc 500x360x300mm wall mounted water closet and including seat cover white and necessary fitting connection to trap etc., , complete all as specified. 18 s&f concealed neo flush tank 80mm full frame and accessories connetion to iron pipe, complete all as specified. 19 s&f ceramic urinal pot of size 37x39x61cm with with inbiult sensor type connection to iron pipe and waste pipe, complete all as specified. cat no : 60018 or quivalent as approved by ge. 20 s&f rectangular shaped urinal partition with forsted glass partition for urinal of 8mm thickof size 900x450mm and necessary cleats for fixing the glass, complete all as specified. 21 s & f aluminium door in lieu of wooden or steel door / window / ventilator, made out of extruded powder coated aluminium sections, with sliding or openable shutters including frame and necessary jointing cleats, glazing clips, powder coated aluminium snap beading, screws etc completerubber beading and handles including connected items with and including, making goodfor dismantling portion in pcc1:2:4 or cm 1:3 , complete all as specified.note : ( i ) minimum thickness of powder coating shall be 15 micron for windows and 25 microns for doors. 22 s & f aluminium window / ventilator in lieu of wooden or steel window / ventilator, made out of extruded powder coated aluminium sections, with sliding or openable shutters including frame and necessary jointing cleats, glazing clips, powder coated aluminium snap beading, screws etc complete and also including powder coated aluminium fittings such as cobra hinges, butt hinges, tower bolts, star lock, hooks & eyes peg stays, rubber beading and handles including connected items with and including, making goodfor dismantling portion in pcc 1:2:4 or cm 1:3 complete all as specified and directed.note : ( i ) minimum thickness of powder coating shall be 15 micron for windows and 25 microns for doors. 23 s & f sheet glass frosted of ordinary quality 3mm thick in panesnexc 0.5 sqm in each pane, complete all as specified. 24 s&f looking mirror of size 1000x600mm and including stainless steel nut & bolts wirh rubber washer , complete all as specified. 25 s&f towel rail 600mm long chorium plated , complete all as specified. make :cat nof450024cp or equivalent as approved by ge. 26 s&f towel ring chorium plated, complete all as specified.make :cat no f450023cp or equivalent as approved by ge. 27 s&f rain shower rose cp 200mm square rubbit cleaning system , complete all as specified. make :cat no f160041cp or equivalent as approved by ge. 28 s & f 75 mm bore, pvc ( swr ) single socketed rain water pipe in any length with rubber ring joints fixed to walls , complete all as specified. 29 m&l 75mm bore pvc ( swr ) floor trap , plain with grating including jointing with solvent cement , complete all as specified. 30 s& f bib tap two in one chorium plated , complete all as specified.make :cat no f160041cpor equivalent as approved by ge. 31 s& f angle cock chorium plated , complete all as specified.make :cat no f280004cp or equivalent as approved by ge. 32 s&f glass corner with chrome finish shelf of size 9 inch x 9 inch for bathroom , complete all as specified. 33 m & l2nd class hard wood, plain straight, solid chawkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, supplied and fixed, complete all as specified. 34 s & f 30 mm thickflush shutters, solid core construction, with block board core and plywood face panels, commericial type on both sides with decorative faces venner with lipping / frame to match , complete all as specified. 35 s & f 100mm long butt hings cast brass mild steel hinge pin, bright polished and fixed type b 11 medium weight & fixed to chowkats, complete all as specified. 36 s&f 150mm long brass handles, fabricated type polished bright , complete all as specified. 37 s&f 200mm long brass barrel tower bolt, but with extruded section polished bright, complete all as specified. 38 s&f mortice lock vertical type size 100mm brass 2 levers , complete all as specified. 39 m&l for interior wall texture paint match to wall and including making smooth finish , complete all as specified. 40 s&f wall mixer cpfancy type connection to iron pipe , complete all as specified. 41 s & f soap dish cp fancy type with brass screws , complete all as specified. 42 m & l for preparing newly plastered surfaces of ceiling and two coats of oil bound distemper ( smooth finish ) , complete all as specified. 43 m & l preparation of old decorated surfaces of walls including complete removal of existing treatment and applying two coats ofdistemper oil emulsionover 1mm thick wallcare putty complete as specified and directed. 44 m & l for bees wax on previously polished surfaces of any description width or girth including cleaning and preparing the surface , complete all as specified. 45 m&l for preparingold steel surface exc 10 cm in width or girth and applying one coats of synthetic enamel paint, complete all as specified. 46 m & l preparation of old wooden surfacesof any description , not other wise described, over 10cm width or girth including and applyingone coat of synthetic enamel paint, complete all as specified. 47 m & l preparing old decorated surfaces of ceilings and applying two coats of white wash, complete all as specified. 48 s & f steel windows with side hung shutters including projecting hinges with steel handle and steel peg stay, complete with glazing bars, both with and without sash bars dovetailed or welded including painting with one shop coat of zinc chromate primer, complete all as specified. 49 s & f sheet glass of ordinary quality 3.00 mm thick in panesnexc 0.5 sqm in each pane, complete all as specified. 50 s & f anodised aluminium door shutters, swing type aluminium sections weighing 0.55 kg / m including necessary joining cleats, glazing clips, rubber neoprene packing handles 2 nos in each door, hinges, anodised aluminium snap beading screws etc , complete all as specified. 51 s&f double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass other parts made of mild steel heavy duty and fixed , complete all as specified. 52 s&f 500 litres capacity rotational moulded polythene water storage tanks ( cylindrical vertical, with closed top ) , hoisted and fixed in position as specified in ssr part i and directed and including taking down old and kept in store , complete all as specified. 53 s&f 20mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed , complete all as specified. 54 s&f 20mm bore ball valves high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. ( min weight 15mm 142 gms / 20mm 210 gmsfixed to iron pipe , complete all as specified. 55 taking up or down steel tubing and connections, including cleaning for re fixing or removal to store 20 mm bore, complete all as specified. 56 taking up or down steel tubing and connections, including cleaning for re fixing or removal to store 15 mm bore, complete all as specified. 57 s & f 20 mm bore gi tubing medium grade with all fittings and fixed complete to walls or laid in floors, complete all as specified. 58 s & f 15 mm bore gi tubing medium grade with all fittings and fixed complete to walls or laid in floors, complete all as specified. 59 s & f sheet glass tinted of ordinary quality 5.00 mm thick or suitable for aluminium glass shutter in panesexc 0.5 sqm in each pane, complete all as specified. 60 complete removal of existing water proofing treatment upto concrete surface of roof slab of any description and of any thickness including removal of water tanks and replacing in same position, cleaning, wire brushing, watering, removal of debris all as specified and directed. ( a ) 10mm thick screed bed in cm 1: 4 with wpc. ( b ) m&l for applying primer @ 0.50 kg / sqm on prepared surface confirming to is 3384 1965. ( c ) a layer of hot blown bitumen grade 85 / 25 as per is 702 1988 @ 1.2 kg / sqm will be applied over primer. ( d ) laying of app membrane polymeric water proofing membrane 3mm thick and weight not less then 3kg / sqm with non woven polyster reinforcement andbonded completely to the substrate & the overlaps are then scale / fused by flame as per manufacture instruction and laying procudere. the minimum overlaps of 100mm shall be allowed at the ends and sides of strips polymeric membrane. ( e ) applying a layer of blown garde bitumen 85 / 25 @ 1.2 kg / sqm and blinding material such as sand in dry condition @ 0.5 to 1.0 kg / sqm shall be dusted over the bitumen ( f ) toping will be done with pcc tiles 25mm thick laid over 15mm screed bedding in layer of cm 1:4 and jointed & pointed in cm 1:4 linseed oil @ 5% by weight of cement shall be mixed with cm for screed and pointing to the brick tiles. after laying the curing shall be cured with water ponding complete all as specified and directed. 61 surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out in soil and loose soil , complete all as specified. 62 m & l 75 mm thick pcc 1:4:8 type d 2 ( 40 mm gradedcrushed stone aggregate ) as in sub base to floors, complete all as specified. 63 m & l 75 mm thick, plain cement concrete1:3:6, type c 2 ( using 40mm graded crushed stone aggregate ) as in plinth protection / hard standing etc, finishing cement concrete surface even and smooth without using extra cement, complete all as specified. 64 m & l sand filling under floors or in foundations including watering and consolidation, complete all as specified. 65 m & l machine pressed precast coloured concrete interlocking paver block rubber moulded any shape and size of 60mm thickness, m 35 grade conforming to is 15658 2006 with grey cement and pigment , complete all as specified. 66 m & lbrick work with sub class b bricks straight or curved on plan exc 6 m mean radius built incm1 : 6 , complete all as specified. 67 s & ftmt steel bars 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including ms wire annealed not less than 0.9 mm dia , complete all as specified. 68 m & l pcc 1 : 3 : 6type c 1 ( 20 mm graded crushed stone aggregate ) in lintel upto 1.5m clear span, cill, steps, seismic and other similiar bands, plinth courses, string courses, laacing courses parapets and railings upto 60 cm in height, bed plates, copings, kerbs, etc. water troughs and the like includind weathering, slightly rounded or chamfered angles and throating , complete all as specified. 69 taking downcarefully aluminiumpointwiring1.5sq mmof complete, switch socket 5amps& power point etc including switches andmakinggooddisturedsurfacesofwalls / ceilingetc , complete all as specified. 70 m & l point wiring for one light point / fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor, frlspvc insulated unsheathed cable in and including 20 mm dia or higer size pvc concealed conduit and fittings with 1.5 sqmm nominal cross sectional area used as continuous earth wire and connected to earth dolly including metal flush boxes with white cover plate andmaking neccessory electrical connection of modular type switches, sockets, regulators etc , complete all as specified. for one light pointor fanpointcontrolled by one switch . 71 all as per item no. 70 but for one 3 pinsocketoutlet5 ampson same board with other switches 72 all as per item no. 70 but for one 3 pinsocketoutlet5 amps socket outletindependent but belowthe switch board of light pointin the same vertical plane 73 m & l for point wiring with 2.5 sqmm ( nominal cross sectional area ) fr pvc insulated & unsheathed 1100 volts grade multi stranded copper conductor single core cable drawn through and including non metallic rigid pvc conduit / pvc casing caping of adequate size with all fittings and accessories including pvc sunk box with 3mm thick plastic laminated sheet top cover complete including fr pvc insulated & unsheathed single core multistranded copper conductor cable of size 1.5 sqmm green in colour as earth continuity conductor connected to common earth dollyfor one 16 amp socket outlet on independent board. 74 s & f switch piano flush type one way 6 amps , complete all as specified. 75 s&f switch piano, flush type, one way, 16 amps , complete all as specified. 76 s & f socket outlet 5 pin, 6 amp flush type, complete all as specified. 77 s&f socket2 in 1, 3 pin, 5 and 16 amps flush type , complete all as specified. 78 s & f ceiling rose surface bakelite three terminals , complete all as specified. 79 s&f led tube light fitting, 1x20 watt surface and wall mounted decorative ultra slim square profile with extruded polycarbonate, environmental friendly, energy efficient ready to use paclk fitting including provn of twin core multi stranded copper cable of size 1.5 sqmm from ceiling rose to tube light fitting , complete all as specified. 80 s&f led tube light fitting, 1x10 watt surface and wall mounted decorative ultra slim square profile with extruded polycarbonate, environmental friendly, energy efficient ready to use paclk fitting including provn of twin core multi stranded copper cable of size 1.5 sqmm from ceiling rose to tube light fitting , complete all as specified. 81 supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230v, 50 hz, rpm 1200, copper winding of sweep 300mm , complete all as specified. 82 s&f epoxy powder coated mcb, db, double door spn 4 way for mcbs with common bus bar at incoming end of outgoing mcbs grouted / flush to wall , complete all as specified. 83 m & l mcb spn 32 amps c series , 240 volts , complete all as specified. 84 m & l mcbsp 32 amps c series , 240 volts, complete all as specified. 85 s&f led spot light with a focused 36 degree beam angle 7 w, round, 3000k including provn of twin core multi stranded copper cable of size 1.5 sqmm from ceiling rose to tube light fitting , complete all as specified. 86 excavation in trenches, not exceeding 1.5 meter wide and not exceeding 1.5 meter in depth for foundation of poles, stays or for taking out / laying of cables and getting out in soft / loose soil , complete all as specified. 87 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in soft / loose soil, complete all as specified. 88 removing excavated materials ( soil ) n. exc 50m and depositing where directed at a level n.exc 1.5m above the starting point , complete all as specified. 89 m & l for sand cushioning to underground cable with clean dry river sand complete all as specified . note: punned thickness only shall be measured & paid. 90 supply & laying of sub class bbricks locally available best quality laid flat ( length of bricks laid across the length of cable ) in tranches for protection of u / g cable , complete all as specified. 91 supply, laying and testing cable xlpe insulated , screened, pvc bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty ) 1100 volts grade with stranded aluminium conductor of size 16 sq mm 2 core, complete all as specified. 92 supply, testing and fixing of new flood light luminaires led type with c clamps mounting and lm6 pressure die cast housing with high efficiency glass cover system, ip 66, power 120 watts and making necessary electrical connection with suitable size pvc insulated copper multi stranded 1100 volts grade cable with suitable size lugs etc , complete all as specified. 93 m&l earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in to ground ( earth pit ) not less than 2.25 meters deep below gl with top edge of earth plate not less than 1.50 m below ground level, connected to gilead wire of 4 mm dia. ( 7.50 m long ) by means of nuts, bolts and washers, check nuts of gi and protected by the gi pipe light grade 1.5 mm nominal bore ( 7.50 m long ) for earth plead wire, watering pipe light grade of 20 mm nominal bore, 0.63 mm thick ci funnel, wire mesh etc complete including necessary earth work and excavation in any type of soil, pcc 1:2:4 type b1 earth pit and precast rcc cover 50 mm thick dully reinforced with 6 mmdia, ms round bars @ 100 mm c / c both ways, earth testing point, making good to floor complete all as specified....

Micro Small And Medium Enterprises - Uttar Pradesh

28568657 procurement of machinery/ equipment for the institute iti electrician course items 1 measuring steel tape 2 combination plier insulated 3 screwdriver insulated 4 screwdriver insulated 5 electrician screwdriver thin stem insulated handle 6 heavy duty screwdriver insulated 7 electrician screwdriver thin stem insulated handle 8 punch centre 9 knife double bladed electrician 10 neon tester 11 steel rule graduated both in metric and english unit 12 hammer, cross peen with handle 13 hammer, ball peen with handle 14 pincer 15 c clamp 16 spanner adjustable drop forged, ss 17 blow lamp brass 18 chisel cold 19 chisel firmer with wooden handle 20 allen key alloy steel 21 grease gun 22 bradawl 23 pully puller with 3 legs 24 bearing puller (inside and outside) 25 pipe vice cast iron with hardened jaw open type 26 scissors blade, ss 27 scissors blade, ss 28 crimping tool 29 wire cutter and stripper 30 mallet hard wood 31 hammer extractor type 32 hacksaw frame 33 try square 34 outside calliper 35 inside calliper 36 divider 37 pliers long nose insulated 38 pliers flat nose insulated 39 pliers round nose insulated 40 tweezers 41 snip straight and bent heavy duty 42 d.e. metric spanner double ended 43 drill hand brace 44 drill s.s. twist block 45 plane cutters 46 smoothing cutters 47 gauge, wire imperial stainlees steel marked in swg & mm 48 file flat 49 file half round 50 file round 51 file flat rough 52 file flat bastard 53 file flat smooth 54 file rasp, half round 55 copper bit soldering iron. 56 de soldering gun 57 hand vice 58 table vice 59 oil can 60 contactor & auxiliary contacts 61 contactor & auxiliary contacts. 62 limit switch 63 rotary switch 64 relaya. cut out relays b. reverse current c. over current d. under voltage 65 pin type, shackle type, egg type & suspension type insulators including hardware fitting 66 hydrometer 67 hand drill machine 68 portable electric drill machine 69 load bank ( lamp / heater type) 70 brake test arrangement with two spring balance rating 71 laboratory type induction coil 72 out side micrometer 73 thermometer digital 74 series test lamp 75 knife switch dpdt fitted with fuse terminals 76 knife switch tpdt fitted with fuse terminals 77 miniature breaker 78 earth plate 79 earth electrode 80 mccb 81 elcb and rccb 82 fuses 83 rheostat (sliding type) 84 capacitors 85 various electronic components 86 various lamps 87 plug socket piano switch lamp holder 88 cables: twisted pair non metallic sheathed cable underground feeder cable ribbon cable metallic sheathed cable multi conductor cable coaxial cable direct buried cable 89 bus bar with brackets 90 rubber mat 91 electrician helmet 92 rcc pole with accessories (ms angle iron, ‘c’ clamp, stay insulator etc.) and materials 93 safety belt 94 ohm meter; series type & shunt type, portable box type 95 digital multi meter 96 a.c. voltmeter m.i. analog, portable box type housed in bakelite case 97 milli voltmeter centre zero analog, portable box type housed in bakelite case 98 ammeter mc analog, portable box type housed in bakelite case 99 ac ammeter mi, analog, portable box type housed in bakelite case 100 kilo wattmeter analog 101 digital wattmeter 102 a.c. energy meter 103 a.c. energy meter 104 power factor meter digital 105 frequency meter 106 magnetic flux meter 107 lux meter 108 tachometer 109 tachometer 110 tong tester / clamp meter 111 megger 112 3 point d.c. starter 113 4 point d.c. starter 114 wheat stone bridge with galvanometer and battery 115 single phase variable auto transformer 116 phase sequence indicator 117 growler 118 ac starters: a. resistance type starter b. direct online starter c. star delta starter manual d. star delta starter – semi automatic e. star delta starter – fully automatic f. star delta starter soft starter g. auto transformer type 119 oscilloscope dual trace 120 function generator 121 soldering iron 122 temperature controlled soldering iron 123 discrete component trainer 124 linear i.c. trainer 125 digital i.c. trainer domestic appliances – 126 a. electric induction plate 127 b. electric kettle 128 c. electric iron 129 d. immersion heater e. a.c. ceiling fan and ac table fan 130 f. geyser (storage type) 131 g. mixture & grinder 132 h. washing machine semi automatic 133 i. motor pump set 134 oil testing kit 135 inverter with battery 136 voltage stabilizer 137 dc power supply 138 battery charger 139 current transformer 140 potential transformer 141 solar panel with battery 142 pentium iv computer or latest 143 ink jet/ laser printer 144 d.c. shunt generator with control panel 145 motor generator (ac to dc) 146 d.c. compound generator with control panel including fitted rheostat, 147 dc series motor coupled with spring balance load 148 dc shunt motor 149 dc compound motor with starter and switch 150 motor generator(dc to ac) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. 151 ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse with mechanical load. 152 ac phase wound slip ring motor with starter switch 153 universal motor with starter/switch 154 synchronous motor with accessories like starter, excitation arrangements. 155 thyristor /igbt controlled d.c. motor drive with tacho generator feedback arrangement 156 thyristor/igbt controlled a.c. motor drive with 157 single phase transformer, 158 three phase transformer, shell type oil cooled with delta/ star 159 electrical machine trainer – 160 diesel generator set with changeover switch, over current breaker and water/ air cooled with armature, star delta connections ac 3 phase 161 used dc generatorsseries, shunt and compound type for overhauling practice 162 pillar electric drill machine motorized 163 motorised bench grinder 164 a.c. series type motor 165 single phase capacitor motor with starter switch 166 manual motor coil winding machine 167 ceiling fan coil winding machine 168 primary current injection set 169 stepper motor with digital 170 shaded pole motor 171 working bench 172 wiring board 173 instructor’s table 174 instructor’s chair 175 metal rack 176 lockers with drawers 177 almirah 178 black board/white board 179 fire extinguisher co2 180 fire buckets...

Directorate of Training and Employment - Uttar Pradesh

27433302 supply of tools, equipment & furniture 2 allen key set of 12 pieces 2mm to 14mm, ( make :taparia / venus / stanley / bosch / hera / pye ) 3 calliper inside with spring15cm, ( make : insize / mitutoyo ) 4 callipers outside with spring 15 cm, ( make : insize / mitutoyo ) 5 dividers with spring 15 cm ( make :taparia / venus / stanley / bosch / hera / pye ) 6 electrician screw driver 250mm, ( make :taparia / venus / stanley / bosch / hera / pye ) 7 philips screw driver set of 5 pieces 100 mm to 300 mm, ( make :taparia / venus / stanley / bosch / hera / pye ) 8 screw driver blade 20cm.x 9mm. ( make :taparia / venus / stanley / bosch / hera / pye ) 9 screw driver blade 30 cm. x 9 mm. ( make :taparia / venus / stanley / bosch / hera / pye ) 10 scriber 15 cm, ( make :taparia / venus / stanley / bosch / hera / pye ) 11 spanner d.e. set of 12 pieces 6mm to 32mm. ( make :taparia / venus / stanley / bosch / hera / pye ) 12 spanner, ring set of 12 6 to 32 mm. ( metric ) 13 spanners socket with speed handle, t bar, ratchet and universal set of 28 pieces with box up to 32 mm. ( ( make :taparia / venus / stanley / bosch / hera / pye ) 14 steel rule 30 cm inch and metric. ( make :taparia / venus / stanley / bosch / hera / pye ) 15 wire cutter and stripper. ( make :taparia / venus / stanley / bosch / hera / pye ) 16 adjustable spanner ( pipe wrench ) 350 mm. ( make :taparia / venus / stanley / bosch / hera / pye ) 17 ac alternator slip ring puller variable 18 air blow gun with standard accessories trigger operated with interchangeable nozzles. ( taparia / venus / stanley / bosch / hera, standered isi ) 19 ammeter dc with external shunt 300a / 60a. 20 air impact wrench with standard accessories. 21 auto electrical test bench for checking dynamo, alternator & starter. with minimum 2hp ac motor, digital voltmeter & ammeter. 22 tap set with matching drills 3 mm to 16mm 23 tap set with matching drills v to 5 / 8 24 refrigerant cylinder 2.5 kg 25 heating kit with infrared bulb ( 200 w capacity ) 26 plumbing hammer weight 200 gm 27 cylinder 134 a 5 kg 28 piercing valve ¼ inch 29 four way reversible valve 30 sling psychro meter mounted on aluminum back scale 10 degree c to +110 degree c 31 fin straightened / fin comb. with strong steel wire based combing on wood 32 wire gauge metric & british. steel plate embossing converse of british & metric 33 dial thermometer remote control, armored capillary dial 75mm 50c to +50 c 34 compressors testers for small hermetic compressors fixed with electrical input / output indicating facilities 35 instrumentation screw driver set 100mm 36 portable air lpg brazing kit 2 kg. lpg cylinder, torches, houses, stand make 37 oxy acetylene welding set completecylinders, regulators welding torches with difference nozzles 38 single door direct cool refrigerator, carrying with hfc and hc 185 l 39 core drill machine. 40 evacuating and refrigerant charging station, consist of na ) rotary two stage vacuum pump and motor ( with gas ballast and anti such back ) nb ) manifold with gauges and valves and capable of pulling vacuum up to 50 microns of hg and with provision of connecting to a microns level vacuum gauge nc ) graduated charging cylinder with provision for temperature correction and all necessary isolating valves ( cap. 2 kg. in lieu of ( b ) above and with accuracy of + / g for charging hydrocarbons ) 41 evacuating and charging station as above but fitted with weighing scale 42 dry n2 cylinder 2 stage regulator or commercial n2 in cylinder with drier unit and 2 stage regulator & meter cube 43 window a.c 1 ton with r 22 blend reciprocating compressor 44 ductable split a.c 1.5 ton 1.5 ton with r134a or r 22 reciprocating compressor 45 recovery unit with cylinders cfc, hfc&hcfc 46 descaling pump set with stainless steel impeller and housing complete with motor 1 / 2 hp nand accessories 47 fan coil unit with water valves ( 2 & 3 way ) 48 shell and tube, dx chillers ( small ) 5 ton with cu tubing only 49 refrigerant cylinder 10 kg capacity 50 gauge manifold with gauges different size of hoses for r 134a, r22 and r 410. ( 3 no’s each ) 51 shell and tube type condenser 5 ton 52 rotary hermetic compressor 2 ton 53 display cabinet 2 ton capacity 54 water cooler storage type 200 l carrying with hfc 134a& reciprocating compressor 55 package a / c 5 ton capacity, air cooled type with open type compressor reciprocating type 56 tool cemented carbide assorted shaped ( external ) for steel turning set of 12 nos. 57 thread plug gauge m 20 & m 21 58 thread ring gauge m 20 & m 21 59 machine chaser m 12 to m 21 ( std. series ) to suit on 60 coventry die head 61 gauge drill grinding 62 magnetic chuck 150 mm dia. ( circulartype ) 63 lathe mandrels ( diff. types ) 64 coventry type die head ( self opening ) 65 collapsible tap with attachment 66 fire extinguisher 67 fire buckets 68 lathe s.s. & s.c. ( all geared head stock ) with minimum specification as: 150 mm center height, to admit 750 mm between centers.machine to be motorized and supplied with coolant installation, 4 jaw independent chuck 150 mm, 3 jaw self centering chuck 150 mm, fixed steady, traveling steady, face plate, driving plate, 4 way tool post, quick change gear box for metric or british threads, live and dead centers with taper attachments, motor capacity 5.5 kw 69 lathe s.s & s.c. ( all geared type ) with minimum specification as:150mm. center height, 1000 mm between centers, gap bed machine to be motorized and supplied with coolant installation, 4 jaw independent chuck 250 mm, 3 jaw self centering chuck 200 mm fixed steady, face plate, driving plate, 4 way tool post, quick change gear box for metric / british threads, live and dead centers with taper attachments, motor capacity n5.5 kw 70 lathe tool room s.s. & s.c. ( all geared type ) with minimum specification as: 150 mm center height, 1000 mm between centers. machine to be motorized and supplied with coolant installation, 4 jaw independent chuck 250 mm, 3 jaw self centering chuck 150 mm fixed steady, traveling steady, face plate, driving plate, 1 way tool post, draw in type collets set up to 25 mm, 0.5 mm, relieving attachments, motor capacity 5.5 kw 71 dividers 200 mm. ( make :taparia / venus / stanley / bosch / pye ) 72 tip cleaner. ( make :taparia / venus / stanley / bosch / pye ) 73 spindle key. ( make :taparia / venus / stanley / bosch / pye ) 74 number punch 6 mm 75 letter punch 6 mm 76 universal weld measuring gauge 77 earth clamp 600a 78 spanner d.e. 6 mm to 32mm. ( make :taparia / venus / stanley / bosch / pye ) 79 s.s tape 5 meters flexible in case. ( make :taparia / venus / stanley / bosch / pye ) 80 electrode holder 600 amps 81 black board and easel with stand 82 flash back arrester ( torch mounted ) 83 flash back arrester ( cylindermounted ) 84 auto darkening welding helmet 85 suitable gas welding table with fire bricks 86 suitable arc welding table with positioner 87 oxygen, acetylene cylinders 88 co2 cylinder 89 argon gas cylinder 90 anvil 12 sq. inches working area with stand 91 swage block 92 die penetrant testing kit 93 magnetic particle testing kit 94 suitable gas cutting table 95 welding simulators for smaw / gtaw / gmaw 96 micrometer outside 0 to 25 mm, least count 0.01 mm with nabl accredited lab. certificate 97 micrometer outside 25 to 50 mm, least count 0.01 mm with nabl accredited lab.certificate 98 micrometer outside 50to 75 mm, least count 0.01 mm with nabl accredited lab. certificate 99 micrometer inside up to 25 mm, least count 0.01 mm with nabl accredited lab. certificate 100 micrometer inside up to 25 to 50 mm, least count 0.01 mm with nabl accredited lab. certificate 101 depth gauge micrometer 0 to 150 mm, least count 0.01 mm with nabl accredited lab. certificate 102 vernier caliper outside, inside and depth 200 mm / 8 inches with metric & inch scale ( l.c. = 0.02mm ) with nabl accredited lab. certificate 103 dial vernier caliper with metric 200 mm, least count 0.05 mm with nabl accredited lab. certificate 104 vernier bevel protractor 300 mm blade with nabl accredited lab. certificate 105 vernier micrometer 0 25 mm o / s lc 0.001mm with nabl accredited lab. certificate 106 vernier micrometer 25 50 mm, outside least count 0.001mm with nabl accredited lab. certificate 107 vernier micrometer 0 inch to 1 inch. outside least count 0.001 inch with nabl accredited lab. certificate 108 gauge feeler thickness 0.05 mm to 0.3 mm by 0.05 ( 6 leaves ) 109 gauge feeler thickness 0.4 mm to 1 mm by 0.1 mm ( 7 leaves ) 110 gauge radius set 1 mm to 25 mm by 0.5 mm 111 centre gauge com. 60°, 55° and 29° 112 screw pitch gauge whitworth & metric each ( 0.25 to 6mm ) 113 drill angle gauge 114 universal dial test indicator plunger type range 0 10 mm, graduation 0.01 mm complete with clamping devices and magnetic stand 115 magnifying glass 75 mm with magnifying factor10x 116 plain ring and plug gauge ( 12, 16, 20, 25, 30, 32, 36, 40, 45, 50mm ) 117 wheel dresser hunting on type with star cutter 118 wheel dresser diamond ( inserted 0.75 or 1 carat ) 119 screw thread micrometer interchangeable ( 0 25 mm ) 120 morse taper plug & ring gauge no. 0 to 7 mt 121 sine bar with centers 200 mm 122 slip gauge metric set ( 87 pieces in a box ) with workshop grade 123 morse taper sleeves no. 0 1, 1 2, 2 3, 3 4, 4 5. 124 drill drift. ( make : taparia / venus / stanley / bosch / pye ) 125 twist drill straight shank 3 to 12 mm by 1mm. ( make : taparia / venus / stanley / bosch / pye ) 126 cnc ( heavyduty ) turnind center description : swing over bad 450mm, xaxis 32x10pmm, motor tourque xaxis 7nm, spindle motor 9kw / 11kw, continuous rating 9kw / 11kw, spindle bore 52 / 63mm, spindle nose a2 6, max barcapacity 42 / 55mm, shuck size 200mm, speed range 50 3000rpm, full power speed 1000 3500 rpm range, std turdia 200mm, no of station 8, tool size 25x25mm, maxbaring bar 40mm, cap. weight 3900kg, machine dimension 2500x1610x1570 inch. ( lxbxh ) , positioning accuracy 0.010mm, repeatableity 0.003mm, quill diameter 80mm, quill stoke 100mm, maxtur dia 300mm, maxtur length 500mm, cross xaxis travel 175mm, longitudinal zaxis 550mm, travel. rapid feed xamdz, axis 24m / min, zaxis 32x10pmm, motor torque zaxis 7nm, with instollation at shop floor area . other then this power conjumption, input / output ratio, gurranty, availavility of engineer time, used computer stage, version and specification. 127 cnc lathe ( hrizonatol & vertical ) automatic automatic cnc lathe macine, horizontal & vertical : lathe machine type horizontal lathe vertical lathe, floor lathe , multi axis lathe., max swing over bed 0 250mm, 250 500mm, 500 750mm, 750 1000mm, 1000 1500mm, › 1500, max spindle speed 500 1000rpm, 2000 3000rpm, 3000 4000rpm, › 4000rpm, max turning diameter 0 500mm, automate grande automatic, condition new, power source electric, pneumatic, type vertical lathe , specilized lathe , horizontol lathe ( with installation at shopfloor are ) other then this power conjumption, input / output ratio, gurranty, availavility of engineer time, used computer stage, version and specification. 128 drafting table 129 drafting table with board 130 work bench 131 steel almirah 132 steel locker 133 steel rack 134 printer table 135 office table big size 136 antivirus 137 wifi device 138 drafting table 139 drafting table with board 140 work bench 141 steel almirah 142 steel locker 143 steel rack 144 printer table 145 office table big size 146 antivirus 147 wifi device 148 desktop computer core i5 letest generation 149 laptop core i5 letest generation 150 all in one desktop core i5 letest generation 151 1000 va ups 152 air conditionar 2 ton split type 153 air conditionar 1.5 ton window type 154 student chair with writing pad 155 dual desk 2 sheeter with storage 156 single desk with storage 157 wooden stool 158 wooden stool long 159 computer table 160 computer chair with arm 161 computer chair without arm 162 revolving chair 163 visitor chair 164 office chair 165 hp 1005 printer 166 sumersible pump 167 instructor table 168 instructor chair 169 drafting board 170 led tv 55 171 multimedia projector 172 dual dc regulated power supply 173 cro dual trace 174 inverter 175 batery 150 ah 176 batery 200 ah 177 digital multi meter 178 digital wattmeter 179 d.c. shunt generator with control 180 motor generator ( ac to dc ) 181 d.c. compound generator 182 m.s. office 183 m.s. window 10 184 dc series motor coupled with spring nbalance load 185 dc compound motor with starter nand switch 186 motor generator ( dc to ac ) set nconsisting of shunt motor with nstarting compensator and switch ndirectly coupled to ac generator with nexciter and switch board mounted nwith regulator, breaker, ammeter, nvoltmeter frequency meter, knife nblade switch and fuses etc. set ncomplete with cast iron bed plate, nfixing bolts, foundation bolts and nflexible coupling. 187 celing fan 1200mm 188 refrigarator 190 ltr 189 tyre changer machine 190 wheel alighment machine 191 wheel balancing machine 192 welding transformer 300amp 193 power hacksaw machine 14 194 classroom table single 195 webcam 196 dvd writer 197 external hard disk 198 online ups 3 kva 199 24 port switch 200 sound system 2.0 201 bluetooth headphone...

National Small Industries Corporation Limited - Uttar Pradesh

27046543 supply , installation and commissioning of machine , tools and equipment for ncvt electrician trade 1 measuring steel tape 2 combination plier insulated 3 screw driver insulated 4 screw driver insulated 5 electrician screw driver thin stem insulated handle 6 heavy duty screw driver insulated 7 electrician screw driver thin stem insulated handle 8 punch centre 9 knife double bladed electrician 10 neon tester 11 steel rule graduated both in metric and english unit 12 hammer, cross peen with handle b. shop tools & equipment ( i ) list of tools & accessories 13 hammer ball peen with handle 14 pincer 15 c clamp 16 spanner adjustable drop forged, ss 17 blow lamp brass 18 chisel cold 19 chisel firmer with wooden handle 20 alien key alloy steel 21 grease gun 22 bradawi 23 pulley puller with s legs 24 bearing puller ( inside and outside ) 25 pipe vice cast iron with hardened jaw open type 26 scissors blade, ss 27 scissors blade, ss 28 crimping tool crimping tool 29 wire cutter and stripper 30 mallet hard wood 31 hammer extractor type 32 hacksaw frame 33 try square 34 outside caliper 35 inside caliper 36 divider 37 pliers long nose insulated 38 pliers flat nose insulated 39 pliers round nose insulated 40 tweezers 41 strip straight and bent heavy duty 42 d.e. metric spanner double ended 43 drill hand brace 44 drill s.s. twist block 45 plane cutters 46 smoothing cutters 47 gauge, wire imperial stainless steel marked in swg & mm 48 file flat 49 file half round 50 file round 51 file flat rough 52 file flat bastard 53 file flat smooth 54 file rasp, half round 55 copper bit soldering iron 56 de soldering gun 57 hand vice 58 table vice 59 oil can 60 contactor & auxiliary contacts 61 contactor & auxiliary contacts 62 limit switch 63 rotary switch 64 relay: a. cut out relays b. reverse current c. over current d. under voltage 65 pin type, shackle type, egg type suspension type insulators including hardware fitting 66 hydrometer 67 hand drill machine 68 portable electric drill machine 69 load bank ( lamp / heater type ) 70 brake test arrangement with two spring balance rating 71 laboratory type induction coil 72 out side cicrometer 73 thermometer digital 74 series test lamp 75 knife switch dpdt fitted with fuse terminals 76 knife switch tpdt fitted with fuse terminals 77 miniature breaker 78 earth plate 79 earth electrode 80 mccb 81 elcb and rccb 82 fuses 83 rheostat ( sliding type ) 84 capacitors 85 various electronic components 86 various lamps 87 plug socket piano switch lamp holder 88 cables 6mm, 2core twisted pair non metallic sheathed cable underground feeder cable ribbon cable metal is sheathed cable multi conductor cable coaxial cable direct buried cable 89 bus bar with brackets 90 rubber mat 91 electrician helmet 92 rcc pole with accessories ( ms angle iron clamp, stay insulator etc. ) and materials 93 safety belt ( ii ) list of equipment 94 ohm meter, series type & shunt type, portable box type 95 digital multi meter 96 a.c. voltmeter m.i. analog, portable box type housed in bakelite case 97 multi voltmeter centre zero analog, portable box type housed in bakelite case 98 ammeter mc analog, portable box type housed in bakelite case. 99 ac ammeter mi analog, portable box type housed in bakelite case. 100 kilo wattmeter analog 101 digital wattmeter 102 a.c. energy meter 103 a.c. energy meter 104 power factor meter digital 105 frequency meter 106 magnetic flux meter 107 lux meter 108 tachometer 109 tachometer 110 tong tester / clamp meter 111 megger 112 3 point d.c. starter 113 4 point d.c. starter 114 wheat stone bridge with galvanometer and battery 115 single phase variable auto transformer 116 phase sequence indicator 117 growler 118 ac starters: a. resistance type starter b. direct on line starter c. star delta starter manual d. star delta starter semi automatic e. star delta starter fully automatic f. star delta starter soft starter g. auto transformer type oscilloscope dual trace 120 function generator 121 soldering iron 122 temperature controlled soldering iron 123 discrete component trainer 124 linear i.c trainer 125 digital i.c trainer 126 domestic appliances: a. electric induction plate b. electric kettle c. electric iron d. immersion heater e. a.c. ceiling fan and ac table fan f. geyser ( storage type ) g. mixture & grinder h. washing machine semi automatic i. motor pump set 127 oil testing kit 128 inverter with battery 129 voltage stabilizer 130 dc power supply 131 battery charger 132 current transformer 133 potential transformer 134 solar panel with battery c. shop machinery 135 d.c. shunt generator with control panel 136 motor generator ( ac to dc ) 137 d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker 138 dc series motor coupled with spring balance load 139 dc shunt motor 140 dc compound motor with starter and switch 141 motor generator ( ac to dc ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate fixing bolts, foundation bolts and flexible coupling 142 ac squirrel cage motor with star delta starter and triple pole iron clad with fuse with mechanical load 143 ac phase wound slip ring motor with starter switch 144 universal motor with starter / switch 145 synchronous motor with accessories like starter, excitation arrangements 146 thyristor / igbt controlled d.c motor drive with tacho generator feedback arrangement 147 thyristor / igbt controlled ac motor drive with 148 single phase transformer, core type, air cooled 149 three phase transformer, shell type oil cooled with delta / star 150 electrical machine trainer 151 diesel generator set with changeover switch over current breaker and water / air cooled with armature, star delta connections ac 3 phase 152 used dc generators series, shunt and compound type for overhauling practice 153 pillar electric drill machine motorized 154 motorized bench grinder 155 ac series type motor 156 single phase capacitor motor with starter switch 157 manual motor coil winding machine 158 ceiling fan coil winding machine 159 primary current injection set 160 stepper motor with digital controller 161 shaded pole motor 162 phase sequence meter 163 component of typical small hydro power unit 164 component of typical water mill 165 fire extinguisher co2 166 fire buckets...

National Small Industries Corporation Limited - Uttar Pradesh

26191007 supply , installation , commissioning on site and training on operation ( s ) and maintenance of tool and equipment for ncvt electrician trade 1 measuring steel tape ( freeman ) 2 combiantion plier insulated ( ambica / pye / venus ) 3 screw driver insulated ( ambica / pye / venus ) & deneers 4 screw driver insulated ( ambica / pye / venus ) & deneers 5 electricain screw driver thin stem insulated handle ( ambica / pye / venus ) & deneers 6 heavy duty screw driver insulated ( ambica / pye / venus ) & deneers 7 electrician screw driver thin stem insulated handle ( ambica / pye / venus ) & deneers 8 punch centre 9 knife double bladed electrician ( iso, std ) 10 neon tester ( ambica / pye / venus ) & deneers 11 steel rule graduated both in metric and english unit ( omega / crystal ) 12 hammer, cross peen with handle ( ambica / pye / venus ) & deneers 13 hammer ball peen with handle ( ambica / pye / venus ) & deneers 14 pincer ( gift, ambitec, ambica ) 15 c clamp ( jst, bst ) 16 spanner adjustable drop forged, ss ( ambica / pye / venus ) & deneers 17 blow lamp brass ( prabhat ) 18 chisel cold ( natraj , shudhir ) & deneers 19 chisel firmer with wooden handle ( gift ) 20 alien key alloy steel ( freeman & ambica, tapria ) 21 grease gun ( ambica / bharat / venus ) 22 bradawi ( gift, std ) 23 pully puller with s legs ( gift ) 24 bearing puller ( inside and outside ) ( gift, std ) 25 pipe vice cast iron with hardened jaw open type ( aries , bharat ) 26 scissors blade, ss ( meerut ) 27 scissors blade, ss ( meerut ) 28 crimping tool ( japson ) crimping tool ( japson ) 29 wire cutter and stripper ( pye ) 30 mallet hard wood ( wodden ) 31 hammer extractor type ( std ) 32 hacksaw frame ( joly& lovly ) 33 try square ( gift / sagar / haricon ) 34 qutside calliper ( gift / sagar / haricon ) 35 inside calliper ( gift / sagar / haricon ) 36 divider ( gift / sagar / haricon ) 37 pliers long nose insulated ( ambitec / pye / venus ) 38 pliers flat nose insulated ( gift / sagar / haricon ) 39 pliers round nose insulated ( gift / sagar / haricon ) 40 tweezers ( iso, std ) 41 strip straight and bent heavy duty ( iso, std ) 42 d.e. metric spanner double ended ( ambica / ambitec / pye ) 43 drill hand brace ( iso, std ) 44 drill s.s. twist block ( miranda ) 45 plane cutters ( bst ) 46 smoothing cutters ( bst ) 47 gauge, wire imperial stainless steel marked in swg & mm ( omega& crystal ) 48 file flat ( jk ) 49 file half round ( jk ) 50 file round ( jk ) 51 file flat rough ( jk ) 52 file flat bastard ( jk ) 53 file flat smooth ( jk ) 54 file rasp, half round ( jk ) 55 copper bit soldering iron ( iso, std ) 56 de soldering gun ( max , c&c , powerway ) 57 hand vice ( gift ) 58 table vice ( aries & lion ) 59 oil can ( priema ) 60 contactor & auxiliary contacts ( l& t ) 61 contactor & auxiliary contacts ( l& t ) 62 limit switch ( iso, std ) 63 rotary switch ( iso, std ) 64 relay: a. cut out relays ( iso, std ) b. reverse current ( iso, std ) c. over current ( iso, std ) d. under voltage ( iso, std ) 65 pin type, shackle type, egg type & suspension type insulators including hardware fitting ( iso, std ) 66 hydrometer ( iso, std ) 67 hand drill machine ( iso, std ) 68 portable electric drill machine ( bocsh ) 69 load bank ( lamp / heater type ) ( c &c , powerway ) 70 brake test arrangement with two spring balance rating ( iso, std ) 71 laboratory type induction coil ( c & c , powerway 72 out side cicrometer ( mitutoyo japan ) 73 thermometer digitel ( iso, std ) 74 series test lamp ( iso, std ) 75 knife switch dpdt fitted with fuse terminals ( iso, std ) 76 knife switch tpdt fitted with fuse terminals ( iso, std ) 77 miniature breaker ( havels ) 78 earth plate ( iso, std ) 79 earth electrode ( iso, std ) 80 mccb ( l& t ) 81 elcb and rccb ( l& t ) 82 fuses ( l& t ) 83 rheostat ( sliding type ) ( iso, std ) 84 capacitors ( iso, std ) 85 various electronic components ( iso, std ) 86 various lamps ( bajaj, orietnt ) 87 plug socket ( arkaylite ) piano switch ( arkaylite ) e ) lamp holder ( arkaylite ) 88 cables ( arkaylite ) 6mm, 2core twisted pair ( arkaylite ) non metallic sheathed cable ( arkaylite ) underground feeder cable ( arkaylite ) ribbon cable ( arkaylite ) metalis sheathed cable ( arkaylite ) multi conductor cable ( arkaylite ) coaxial cable ( arkaylite ) 89 bus bar with brackets ( arkaylite ) 90 rubber mat ( std , isi ) 91 electrician helmet ( isi, ) 92 rcc pole with accessories ( ms angle iron c clamp, stay insulator etc. ) and materials ( isi, std ) 93 safety belt ( isi ) ( ii ) list 94 ohm meter, series type & shunt type, portable box type ( c& c, powerway ) 95 digital multi meter ( htc ) 96 a.c. voltmeter m.i. analog, portable box type housed in bakelite case ( c&c , powerway ) 97 multi voltmeter centre zero analog, portable box type housed in bakelite case ( c&c, powerway / denco ) 98 ammeter mc analog, portable box type housed in bakelite case. ( c&c, powerway / denco ) 99 ac ammeter mi analog, portable box type housed bakelite case. ( c&c, powerway / denco ) 100 kilo wattmeter analog ( c&c, powerway / denco ) 101 digital wattmeter ( c&c, powerway / denco ) 102 a.c. energy meter ( isi, japson ) 103 a.c. energy meter ( isi, japson ) 104 power factor meter digital ( c&c, powerway / denco ) 105 frequency meter ( c&c, powerway / denco ) 106 magnetic flux meter ( c&c, powerway / denco ) 107 lux meter ( c&c, powerway / denco ) 108 tachometer ( c&c, powerway / denco ) 109 tachometer ( c&c, powerway / denco ) 110 tong tester / clamp meter ( c&c, powerway / denco ) 111 megger ( c&c, powerway / denco ) 112 3 point d.c. starter ( c&c, powerway / denco ) 113 4 point d.c. starter ( c&c, powerway / denco ) 114 wheat stone bridge with galvanometer and battery ( c&c, powerway / denco ) 115 single phase variable auto transformer 116 phase sequence indicator ( c&c, powerway / denco ) 117 growler ( isi, std, ) 118 ac starters: a. resistance type starter ( c& c, powerway ) b. direct on line starter ( l& t, apex ) c. star delta starter manual ( l& t, appex ) d. star delta starter semi automatic ( l& t , appex ) e. star delta starter fully automatic ( l&t, appex ) 119 oscilloscope dual trace ( htc, owon ) 120 function generator ( powerway, c&c ) 121 soldering iron ( tony , jk ) 122 temperature controlled soldering iron ( jk, tony 123 discrete component trainer ( c&c , powerway 124 linear i.c trainer ( c & c, powerway ) 125 digital i.c trainer ( powerway, c&c ) 126 domestic appliances: a. electric induction plate ( usha, b. electric kettle ( isi, std, ) c. electric iron ( usha, havells ) d. immersion heater ( havells, arkylite ) e. a.c. ceiling fan and ac table fan ( usha, havells ) f. geyser ( storage type ) ( usha, bajaj ) g. mixture & grinder ( havells, arkylite ) h. washing machine semi automatic ( lg, godrej ) 127 oil testing kit ( bajaj, l&t, c&c ) 128 inverter with battery ( microtec, luminus, ) 129 voltage stablizer ( national, vegaurd ) 130 dc power supply ( c&c , powerway ) 131 battery charger ( national, c&c ) 132 current transformer ( isi, std, ) 133 potential transformer ( isi, std, ) 134 solar panel with battery ( sukam, luminus ) 135 pentium iv computer or latest ( hp, dell ) 136 ink jet / laser printer ( hp, canon ) c. 137 d.c. shunt generator with control panel ( c& powerway / denco ) 138 motor generator ( ac to dc ) ( c&c, powerway / denco ) 139 d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker ( c&c, powerway / denco ) 140 dc series motor coupled with spring balance load ( c&c, powerway / denco ) 141 dc shunt motor ( c&c, powerway / denco ) 142 dc compound motor with starter and switch ( c&c, powerway / denco ) 143 motor generator ( ac to dc ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc, set complete with cast iron bed plate fixing bolts, foundation bolts and flexible coupling. ( c&c, powerway / denco ) 144 ac squirrel cage moter with star delta starter and triple pole iron clad swith fuse with mechanical load. ( c&c, powerway / denco ) 145 ac phase wound slip ring motor with starter switch ( c&c, powerway / denco ) 146 universal motor with starter / switch ( c&c, powerway / denco ) 147 synchronous motor with accessories like starter, excitation arrangements ( c&c, powerway / denco ) 148 thyrisor / igbt controlled d.c moter drive with tacho generator feedback arrangement ( c&c, powerway / denco ) 149 thyristor / igbt controlled ac motor drive with ( c&c, powerway / denco ) 150 single phase transformer, core type, air cooled ( c& powerway / denco ) 151 three phase transformer, shell type oil cooled with delta / star ( c&c, powerway / denco ) 152 electrical machine trainer ( c&c, powerway / denco ) 153 diesel generator set with change over switch over current breaker and water / air cooled with armature, star delta connections ac 3 phase ( c&c, powerway / denco ) 154 used dc generators series, shunt and compound type for overhauling practice ( c&c, powerway / denco ) 155 pillar electric drill machine motorized ( c&c, powerway / denco ) 156 motorised bench grinder ( c&c, powerway / denco ) 157 ac series type motor ( c&c, powerway / denco ) 158 single phase capacitor motor with starter switch 159 manual motor coil winding machine ( c&c, powerway / denco ) 160 ceilling fan coil winding machine ( c&c, powerway / denco ) 161 primary current injection set ( c&c, powerway / denco ) 162 stepper motor with digital controller ( c&c, powerway / denco ) 163 shaded pole motor ( c&c, powerway / denco ) 164 working bench ( mango wood ) 165 wiring board ( mango wood ) 166 instructors table ( iso, std ) 167 instructors chair ( iso, std ) 168 metal rack ( iso, std ) 169 locker with drawers ( iso, std ) 170 almirah ( iso, std ) 171 black board / white board ( iso, std ) 172 fire extinguisher co2 ( iso isi ) 173 fire buckets ( iso tata ) 174 phase sequence meter 175 component of typical small hydro power unit 176 component of typical water mill...

Uttar Pradesh Cooperative Sugar Factories Federation Limited - Uttar Pradesh

24874604 competitive e bidding for fabrication, erection and dismantling from reputed contractors 2 general work 3 dismantling of m.s. pipe 2 cm to 35 cm size. 4 erection of m.s. pipe 2 cm to 35 cm size. 5 dismantling , fabrication and erection of pipe fitting size 2cm to 35 cm 6 bend 7 flange 8 nipple 9 cross / tee 10 valve 11 reducer 12 dismantling of m.s. pipe above to 35 cm size & shifting it to scrap yard. 13 fabrication and erection of m.s. pipe above to 35 cm size by 6 / 8 / 10 mm plate. 14 dismantling , fabrication and erection of pipe fitting above 35 cm size. 15 bend 16 reducer 17 nipple 18 cross / tee 19 valve 20 dismantling of old bed and fabrication, erection, alignment & trial of new bed of motor, pump or r / g box. 21 10 hp to 20 hp 22 25 hp to 60 hp 23 75 hp to 125 hp 24 150 hp to 250 hp 25 patching work in different type of rectanglur, square & ciruler old equipments by new / old plate as available. 26 dismantling of old rectangular / circular tank and shifting them to scrap yard. 27 fabrication and erection of new rectangular / circular tank by new / old plate. 28 flat bottom 29 conical bottom 30 dismantling of light structure 31 fabrication and erection of light structure. 32 dismantling of heavy structure. 33 fabrication and erection of heavy structure. 34 replacement of old worn out platform by new or old plate. 35 fabrication and fitting of shed by old g.i. sheet for db, motor etc in different places. 36 repairing of trusses of mill house, boiling house etc by welding or fitting missing or worn out nut and bolts. 37 straightening bent m.s. plates for reuse. 38 dismantling fabrication and erection of header with flange and nipple etc. 39 size 2.5 cm to 12.5 cm 40 size 15 cm to 30 cm 41 replacement of cone of different equipments by old / new m.s. plate. 42 up to 1 meter dia 43 above 1 meter dia 44 repairing of m.s. gutter at different places. 45 fabrication and erection of new gutter in place of worn out gutters by old / new plates. 46 fabrication and erection of new gutter by old / new m.s. plate. 47 repairing of worn out column and beam in mill 48 dismantling of worn out coils and fabrication erection of new coil by new pipe. 49 fabrication of electric pole up to 27 long with base by 4, 6, 8 old or new pipes. cross arm to be fitted. 50 fabrication and erection of step type stairs with railing etc for different places. 51 mill house 52 forzing of cane carrier / bagasse carrier side links as per required size. 53 dismantling and erection of worn out runner of cane carrier / src / rake carrier / bagasse elevator / rbc. 54 repairing of old rakes of s.r.c. / inter rake carrier. 55 repairing of r.b.c. and bagasse elevator slates 56 fabrication of new rakes for src / inter rake carrier by m.s. plate 57 replacement of worn out side plate of rake carrier / bagasse elevator / rbc / up to 300 mm height by new / old plate. 58 replacement of worn out side plate of cane carrier by new / old plate and strengthening of its lower side support. 59 dismantling and erection of side & bottom plate of src / rake carrier / bagasse elevator & rbc above to 300 mm size. flat and angle to be fitted out side of bottom plate for strengthening. 60 fabrication & erection of guide in cane carrier / src / bagasse elevator and rbc by bending angle and plate. 61 dismantling of worn out box of src / rake carrier and erection of new box in place of it. 62 150 x 150 mm 63 200 x 200 mm 64 replacement of weak side and top plate from cane chopper to fibrizer by old / new plate. 65 fabrication and erection of juice distribution chute. 66 dismantling of worn out rail of cane unloader and erection of new rail at its place. 67 dismantling of worn out squire bar of unloader and erecting of new squire bar at its place. 68 dismantling of bottom and side worn out portion of d.s.m. screen and fitting of new plate in its place. 69 dismantling of old screw conveyor and fabrication and erection of new screw conveyor in its place according to size 70 replacement of worn out portion of bottom trough of screw conveyor by new / old plate 71 half circumference portion 72 hole type half circumference portion by m.s. plate 73 hole type half circumference portion by s.s. plate 74 repairing of defective tawas of mill screw conveyor. 75 hard facing work of mill roller crown pinion teethes. 76 replacemen of worn out angle / channel / beam of cane carrier / rake carrier / bagasse elevator and rbc. 77 angle 78 chanel 79 beam 80 fabrication and erection of trpf rollers top & bottom cover by new / old m.s. plate 81 hard facing work of trpf rollers shell and teeth. 82 dismantling of mill head stock and its erection accordingly with all accessories. 83 line level of inter rake carrier and worn out side plates of tail and driving end shafts guides to be replace by m.s. plate. erection after line alignment with satisfactory trial. 84 fabrication and erection of mill pressure chute by new m.s. plate. lining of s.s. plate to be fitted on it and strengthening of top and bottom plate to be done. fitting accordingly as per old chute to be done. 85 replacement of old s.s. lining of pressure chute . new s.s. lining to be fitted accordingly as per old chute. assembly and strengthening to be done. 86 bagacilo screens of bagasse elevator to be taken out and their fitting to proper place after repairing / setting them straight / right. 87 checking of mill juice tray, replacement of worn out portion, arresting of leakages with welding of s.s. / m.s. electrodes with satisfactory trial. 88 repairing work of worn out blades of bagacillo blower with satisfactory trial. 89 fabrication erection and satisfactory trial work of new bagacillo blower. 90 dismantling of worn out deflector plate of fibrizer with beam. fabrication and erection of new deflector plate accordingly as perold plate. 91 cane carriers all three runners beams line alignment and level to be set right and satisfactory trial work to be done. 92 line alignment work of head and tail end shaft of secondary rake carrier / irc to be done. its worn out runner and angle to be replaced and satisfactory trial to be done. 93 boiler house 94 fabrication of new rakes for rbc and bagasse elevator. approximate weight of 01 rake is 12 kg. 95 repairing of old rakes of rbc and bagasse elevator. 96 replacement of worn out portion of boiler flue gas / air heater ducting by old / new plate. 97 patching work over worn out portion of boiler flue gas ducting by old / new plate. 98 after dismantling of old flue gas ducting damper, new damper to be fabricated and erected. 99 after dismantling of old f.d. fan air ducting damper, new damper to be fabricated and erected. 100 repairing of bagasse feeding sliding gate of boilers . 101 erection of id fan casing after replacement or patching of worn out portion of it by old / new plate. 102 fabrication and erection of worn out bagasse feeding chute of boilers by old / new plates. 103 repairing / replacing of old worn out fins of 20 ton boilers economizer tube. 104 dismantling , modification and erection of boiler flue gas ducting as per instruction. 105 after dismantling worn out wear plate of id fan impeller vain, new plate to be fitted and hard faced as per instruction. 106 fabrication and erection of new suction cone of boiler id fan by old / new plate. 107 worn out portion of boiler ash discharge chute to be taken out. fabrication and erection of new ash discharge chute of boilers. 108 replacement of old tubes of air heater by new tubes. 109 fabrication of old tubes of boilers according to the size of air heater tubes and their erection to air heater. 110 dismantling of old i.d. fan with casing of boilers and shifting it to scrap yard and erection of new i.d. fan with casing and inlet , outlet connections in its place and satisfactory trial to be done. 111 dismantling of old i.d. fan and erection of new i.d. fan inplace of old one with satisfactory trial. 112 boiling house 113 old brass / ss tubes of quad / juice heater / pans to be taken out and depositing them to store. new tubes to be fitted, expended and to be trialed at 80 lbs pressure. 114 juice heater / semikestner 115 vapor shell / quad / pan 116 weak save all of quad / pans to be repaired by new / old plate and to fit / erect them. 117 fabrication and erection work of save all by 8 mm m.s. plate in place of quad / pans worn out save all according to instructions. satisfactory trial is needed. 118 fabrication and erection of steiner with nipple in place of raw juice / sulphited juice / syrup / melter pumps worn out / old strainers. 119 weak catchers worn out portion of quad / pan to be taken out. repairing to be done by provided plates. fins to be prepared and fitted to them. 120 top and bottom portion worn out partition plate of juice heater / vapor line juice heater dismantling and new partition plate fabrication erection work to be done . 121 for fitting of rubber strip on partition plate of juice heater / vapor line juice heater, flat iron to be fitted according to instruction and rubber strip to be fitted and trial to be done. 122 dismantling, fabrication and erection of worn out condenser of vacuum filter along with all connections and satisfactory trial. 123 dismantling fabrication erection of condensate bottle of quad / semekestner / vapor cell / juice heater along with all connections. dismantled material to be shifted to scrap yard. 124 repairing work of aerator of effluent treatment plant. 125 c.i.cross 6 size dismantling fabrication and erection work at sulphur station. blinds to be fitted to both end of cross. 126 dismantling fabrication and erection work of steiner for spray / injection pump suction pipe. 127 dismantling of worn out portion of vacuum filter trough . plate to be bend according to size and to be fitted in trough. 128 dismantling fabrication and erection of channel and beam of condenser. 129 quad / pan entrainment catcher inside worn out channel, angle dismantling and new channel, angle erection work. 130 6 size worn out coils of clarifier dismantling, new fabricating erection with nipple and trial to be done. 131 dismantling of worn out down take of semikestner, vapor cell, quad, pan and fabrication erection of new down take by 6 / 8 mm plate with trial. 132 crystallizers broken / tilted arms to be taken out. after repairing them or making new to be fitted to proper place and trial to be given. 133 40 / 60 ton pan discharge valves worn out body / chute dismantling work and fabrication erection work of new body / chute. 134 weak catcher of quad and pans dismantling work and fabrication erection work of new catcher according to instructions. 135 crystallizers worn out gland, bush, replacing work, shaft repairing work , worm wheel opening and fitting work and satisfactory trial to be given. 136 spray system pipe line blinds to be opened, cleaned and to be fitted after cleaning with satisfactory trial. 137 spray system worn out branch pipe line dismantling and new branch line erection work and satisfactory trial to be done. 138 quad / pan worn out umbrella dismantling and new umbrella fabrication erection work to be done. 139 weak syrup / molasses tanks of pan station to be taken out .new tanks to be fabricate and erect by 6 / 8 mm thick plate. braising of angles to be provided along with necessary connection to tanks. 140 vapor shell / semikestner / quad pans worn out ammonia coil dismantling and new ammonia coil fabrication erction work with trial. 141 sugar hopper weak and worn out driving unit / trough to be dismantled. fabrication and erection of new drive unit / trough with angle . trial to be done. 142 fabrication and erection of new chute of s.d. machine pug mill gate. 143 a machines old hood dismantling and new hood fabrication erection work . 144 fabrication of new bucket as per sample for dry seed elevator / sugar elevator. 145 fabrication and erection of stirrer to molasses condenser of pan station. by making bed plate , motor reduction gear to be fitted for operating stirrer. satisfactory trial to be done. 146 fabrication and erection of new coil by pipe for super heated wash water system. hydraulic testing to be done. 147 broken shaft of pug mill drive to be linked to proper place. new flange type coupling to be made fit to fit in it . rib to be provided according to instruction. 148 new belt conveyor is to be fabricated and fitted on 8 x 16 vacuum filter with satisfactory trial. 149 new coil for d super heater is to be fabricated and to be fitted as directed with nozzles and satisfactory trial is to be given. 150 fabrication, erection with shaft and satisfactory trial of screw conveyor for vacuum filter mud mixture. 151 dismantling, fabrication and erection of vacuum filter mud mixture with satisfactory trial. 152 vacuum crystallizer weak and worn out shell dismantling work and fabrication erection of new shell in its place. 153 dismantling and erection of worn out beam / channel of centrifugal machine . 154 clarifier top and flocculaty chamber worn out plate dismantling work and fabrication erection by new plate. leak proof trial to be done. 155 sulphur furnace weak and worn out body shell with water jacket to be dismantled and shift to scrap yard. fabrication erection of new shell and water jacket alongwith all necessary connections. leak proof trial to be done. 156 vacuum filter weak and worn out filtrate bottle to be dismantled and shift to scrap yard. fabrication and erection of new bottle along with all connections. leak proof trial to be done. 157 sulphur furnace cooler worn out coil pipe to be taken out , new pipe to be fitted and leak proof trial to be done. 158 worn out quad / juice heater condensate bottle to be dismantled and shift to scrap yard. fabrication and erection of new bottle with partition plate in its place. trial to be given. 159 replacement of partition plate of quad / juice heater condensate bottle. 160 junction box of spray pipe line to be opened, taken out, their pipes and nozzles to be cleaned and o fit them again after necessary repairing . 161 weak and worn out portion of spray / injection pump suction pipe to be taken out and to repair by new / old plates. 162 weak and worn out duck foot bend of pan / quad tail pipe to be dismantled. fabrication and erection of new duck foot bend in its place. 163 agitator of vacuum filter to be repaired. 164 for hydraulic testing of vapor line juice heater m.s. pipe blinds be provided inside suction and delivery vapor pipe of v.l.j.h. and blinds be taken out after hydraulic testing. 165 exhaust vapor valve to be opened its weak portion to be patched by 8 / 10 mm thick plate. assembled after patching and leak proof trial to be done. 166 juice / syrup sulphiter recovery tower worn out shell size 1 meter dia x 3 meter height to be dismantled and to shift scrap yard . fabrication and erection of above shell by old / new plate according to drawing. leak proof trial to be done. 167 dismantling of worn out melter of sulphur furnace, shifting it to scrap yard. fabrication and erection of new melter by 8 / 10 mm plate. coils to be made and to erect it by new pipe. trial to be done. 168 dismantling of worn out circular tank of juice / water / molasses weighing scale. fabrication and erection of new tank by provided old / new plates. its valve seat work to be done and trial to be done. 169 dismantling of worn out spruzer of juiced sulphiter. fabrication and erection of spruzer by new pipe. leak proof trial to be done. 170 dismantling of worn out mud distribution box of clarifier. fabrication and erection of new mud distribution box by new plate. trial to be done. 171 worn out agitator of vacuum filter is to be taken out and new is to be fabricated and fitted. satisfactory trial is to be given. 172 partition plate of compartment of clarifier to be replaced 173 dismantling of clarifier flash tank. new to be erected. its worn out pipe to be replaced and leak proof trial to be done. 174 dismantling of weak shell and top of 40 ton cap pan and shifting it to scrap yard. fabrication and erection of new shall and top. 175 dismantling of weak shell and top 60 ton cap pan and shifting it to scrap yard. fabrication and erection of new shell and top by new / old plate. 176 dismantling of save all of top cone of 60 ton pan and shifting it to scrap yard. fabrication and erection of new save all top cone in its place. trial to be done. 177 dismantling of save all of top cone of 40 ton pan and shifting it to scrap yard. fabrication and erection of new save all top cone in its place. trial to be done. 178 60 / 40 ton pans discharge valve bearing housings plate to be replaced by new plate and trial to be done. 179 60 / 40 ton pans condensers tail pipes duck foot bend to be dismantled and fabrication erection of new duck foot bend to be done by new plate and trial to be done. 180 dismantling of worn out shell and bottom of juice sulphiter. fabrication and erection of new shell and bottom by 8 / 10 mm thick plate with juice, gas and lime line connection .partition plate and stirrer to be fitted to proper place in side sulphiter. satisfactory trial to be done. 181 dismantling of worn out coolers of sulphur furnace. fabrication and erection of coolers by 8 mm m.s. plate. cooling pipe, gas pipe connection to be done. satisfactory trial to be done. and dismantled material to be shifted in scrap yard. 182 weak lower portion of shell of sulphur furnace coolers to be dismantled. fabrication erection to be done. worn out cooler pipes to be replaced. 183 dismantling fabrication erection of weak roof of clarifier by 8 mm thick plate. weak tray of dorr to be taken out and 6mm thick plate to be patched in its place. 184 dismantling of worn out catcher bottle of vacuum filter. fabrication and erection of new catcher bottle in its place. all connections and trials to be done. 185 dismantling of worn out cyclone of vacuum filter station. fabrication and erection of new cyclones by 3 / 5 mm thick plate with satisfactory trial. 186 800 m² old semikestner worn out roof, bottom and 30 % shall to be dismantled. fabrication and erection to be done by 10 mm thick plate and trial to be done. 187 quad body weak bottom to be dismantled. fabrication and erection to be done by old or new plate. all connections to be done . trial to be done. 188 spray / injection pumps delivery headers weak portion to be dismantled. new to be fabricated by new / old plates and erected with satisfactory trial. 189 dismantling of 3 size worn out steam coil of b heavy molasses conditioner and fabrication erection of new coil with its trial. 190 fabrication and erection of sulphur furnace melter coil in place of worn out coil with all connections and satisfactory trial. 191 dismantling of old worn out air plate of hopper . fabrication and erection of new plate by 3mm new m.s. plate in its place. 192 old tank of a light and a molasses to be dismantled. new to be fabricated by 6 / 8 mm m.s. plate and erected in its place. satisfactory trial to be done. 193 all 04 no fins of pan no. 7 mechanical circulator to be taken out. new fins with housing to be erected in its place. trial to be done. 194 worn out bottom portion of b heavy molasses conditioner to be dismantled. new to be fabricated by 6 / 8 mm m.s. plate and erected in its place. 195 worn out circular bottom plate of crystallizer to be dismantled. new to be fabricated by new m.s. plate and erected in its plate. leek proof trial to be done. 196 dismantling of complete shell of 60 ton pan and shift it to scrap yard. fabrication and erection of complete shell of 60 ton pan by 10 / 12 mm thick plate. satisfactory water and vacuum trial to be given. 197 dismantling of save all dome of 60 ton pan and shift it to scrap yard. fabrication and erection of save all dome of 60 ton pan by 10 / 12 mm thick plate. satisfactory water and vacuum trial to be given. 198 syrup sulphiter weak and worn out portion of shell to be dismantled and shift it to scrap yard. fabrication and erection of above shell by provided new plate of 8 mm thick. satisfactory trial to be given. 199 dismantling of weak old hot water overhead tank and condensate water receiving tank of pan and shift them to scrap yard. fabrication and erection of new tanks by 8 / 10 mm thick plate with all necessary connections. 200 dismantling of worn out baffle plate of juice sulphiter and shifting it to scrap yard. fabrication and erection of new baffle plate in its place. 201 dismantling of worn out dorr clear juice distribution box and shifting it to scrap yard. fabrication and erection of new clear juice distribution box in its place with all connections. 202 dismantling of old trough of hoppers and shifting them to scrap yard. fabrication and erection of new trough with support angle and fitting of wooden strip. satisfactory trial to be given. 203 erection of magma mixture for b or c c / f m / c with its drive system, bed and all pipe line connection. satisfactory trial is to be given. 204 dismantling of all 03 sulphur furnaces with their auxiliary equipments, accessories and pipe lines from old plate farm and shift them to directed place and their erection at new platform along with all equipments, connections and satisfactory trial. 205 dismantling of clarifier central shaft with stirrer arms and r.g. box. fabrication and erection of new central shaft with all accessories. satisfactory trial to be given. 206 dismantling of old juice sulphiter / clear juice / syrup receiving bottle and shifting them to scrap yard. fabrication and erection of new bottle with all connections. satisfactory trial to be given. 207 fabrication and erection of b and c c / f m / c top cover by provided new / old m.s. plate with satisfactory trial. 208 fabrication and erection of b and c c / f m / c molasses separator by provided new / old m.s. plate and satisfactory trial to be given. 209 fitting of diffusers in aeration tank with all connections and satisfactory trial to be given. 210 fabrication of m.s. perforated box of size 1½ ?x 1 x 2 ? and fitting it in mgf / acf 211 dismantling of a centrifugal machine size kcp 32 ? x 49 ? with its pug mill, column and structure and sift it to directed place. 212 repairing of pugmill with drive arms by providing plates and angle. satisfactory trial to be given. 213 dismantling of old trough of hopper and shifting them to scrap yard. fabrication and erection of new trough with dubbing plate, and wooden connecting rod housing in those places. satisfactory trial to be given....

Directorate of Training and Employment - Uttar Pradesh

23933271 supply of raw material & tools 2 teel rule with metric & british graduation 150 mm, stainless steel 3 try square. 150 mm blade 4 caliper inside spring type. 150 mm 5 caliper hermaphrodite spring type 150 mm 6 caliper outside spring type 150 mm 7 divider spring type 150 mm 8 centre punch 10 mm and length 120 mm 9 screw driver 150mm insulated flat type 10 chisel cold flat 20 mm x 150 mm high carboon steel 11 hammer ball peen with handle 450 grams ( 1 lb ) 12 hammer ball peen with handle. 220 grams ( 1 / 2 lb ) 13 file flat second cut 250 mm 14 file half round second cut 150 mm. 15 hacksaw frame fixed type 300 mm 16 safety goggles. 17 dot punch 100 mm 18 straight edge steel 300 mm or above 19 spirit level metal type 2 300 mm basic length accuracy 0.1mm / meter 20 stud extractor ezy out set of 8 21 micrometer outside. 0 25 mm 22 micrometer outside. 25 50 mm 23 micrometer outside. 50 75 mm 24 micrometer inside with extension rods. accuracy 0.01 mm with extension rods upto 150 mm 25 vernier caliper 150 mm 26 vernier height gauges 0 300 mm with least count = 0.02 mm 27 vernier bevel protractor blade with acute angle attachment 300 mm 28 screw pitch gauge metric 0.25 to 6 mm 29 wire gauge, metric standard. 30 surface plate c.i / granite with stand and cover 600 x 600 mm 31 marking table ( mild steel ) 900x900x900 mm 32 universal scribing block. 220 mm 33 v block pair with clamps 150 x 100 x 100 mm 34 angle plate 150 x 150 x 250 mm 35 punch letter set. 3 mm 36 portable hand drill ( electric ) 0 to 13 mm capacity 37 drill twist straight shank 3 mm to 12 mm by 0.5 mm h.s.s. 38 drill twist taper shank 8 mm to 20 mm by 0.5 mm h.s.s. 39 taps and dies complete set in box. wit worth 40 taps and dies complete set 5, 6, 8, 10 & 12 mm set of 5 41 file knife edge smooth 150 mm 42 file feather edge smooth 150 mm 43 file triangular smooth 200 mm 44 file round second cut 200 mm 45 file square second cut 250 mm 46 feeler gauge gauge feeler / thickness 0.05 mm to 0.3 mm by 0.05 and 0.4 mm to 1 mm by 0.1 mm 13 leaves 47 file triangular second cut. 200 mm 48 file flat second cut safe edge. 300 mm 49 file swiss type needle set of 12, length = 150 mm 50 file half round second cut. 250 mm 51 file half round bastard. 250 mm 52 file round bastard. 250 mm 53 file hand second cut. 150 mm 54 file card. 3x5 size, brass or steel wire 55 oil can 250 ml 56 pliers combination insulated 150 mm 57 wooden handle forged soldering iron copper bit. 230v, 250 w, 350 gm 58 blow lamp 0.5 litre 59 spanner double ended 6x7, 8x9, 10x11, 12x13, 14x15, 16x17, 18x19, 20x22 60 spanner adjustable 150 mm 61 interchangeable ratchet socket set 12 mm driver, sized10 32 mm set of 18 socket & attachments. 62 double ended tubular box spanner set with tommy bar. a / f 6 25 mm set of 10 tommy bar dia 6, 8, 10, 12, 14, 16 63 glass magnifying 75 mm 64 clamp toolmaker 5 cm and 7.5 cm set of 2. 65 clamp c 100 mm 66 clamp c 200 mm 67 hand reamer set ( tapar pin straight flute ) nominal dia 6, 8, 10, 12, 16mm 68 machine reamer parallel ( helical flute ) 12 16mm set of 5. 69 scraper flat 150 mm 70 scraper triangular 150 mm 71 scraper half round 150 mm 72 chisel cold cross cut & diamond point. 9 mm x 150 mm 73 chisel cold flat 9 mm x 100 mm 74 chisel cold round noze. 9 mm x 100 mm 75 pipe wrench 400 mm 76 pipe vice 100 mm 77 adjustable pipe die set bsp cover pipe size 1 or 3 / 4 78 wheel dresser ( one for 4 units ) star / dresser with holder length 150 mm, diamond point 79 machine vice swivel base 100 mm 80 machine vice swivel base 125 mm 81 sleeve drill morse no. 0 1, 1 2, 2 3, 3 4, 4 82 vice bench 150 mm 83 bench working. 2400 x 1200 x 900 mm 84 almirah. 1800 x 900 x 450 mm 85 lockers with 8 drawers ( standard size ) . one locker for each trainee 86 metal rack 1820 x 1820 x 450 cm 87 black board with easel. 88 fire extinguisher ( for 4 units ) co2 type, 3 kg capacity 89 machine vice. 100mm 90 torque wrench ( standard / ratchet type ) 14 to 68 nm 91 power tools for fastening capacity 10 18mm 92 different profile gauges ( plate type ) for demonstration metric standard 93 knurling tool ( diamond, straight & diagonal ) 94 indexable boring bar with inserts 1 shank 95 machine maintenance mannual for lathe, pedestal grinder, drill machine, power saw 96 temperature gauge range 0 150°c 97 dowel pin ( straight ) dia. 1 length 4 ( mat: stainless steel ) 98 standard tap screws m3, m4, m5, m6, m8, m10, m12, m14, m16 99 lapping plate dia. 6 100 medium carbon heat treated alloy steel metric studs and bolts along with nuts ( for display ) of standard length ( may be manufactured in house ) m6, m8, m10, m12, m14, m16 ( standard ) 101 caps screws m6, m8, m10, m12 102 drill gauges letter drill gauge ( a to z ) , number drill gauge ( 1 to 60 ) , metric drill gauge ( 1.5mm to 12.5mm, 30 holes ) 103 cast iron globe valve ( flanged type ) 150nb, class# 150 flange:ansi125 b16.1 104 c.i. sluice / gate valve ( flanged type ) 150nb, class# 150 flange:ansi125 b16.1 105 stop cock 25nb ( 2 way, threaded end ) 106 m.s. pipe 150nb, sch.40, erw, is:1239 107 g.i. pipe 25mm, sch.40, erw 108 slip on forged steel flange 150nb, ansi b16.5, class#150 109 bolt & nut with washer ( may be manufactured in house ) m20x2.5x90 long ( part thread hex. head ) 110 pipe threading die with handle ratchet type die head of 1 / 2 , 3 / 4 and 1 111 jigs & fixture ( sample ) for demonstration ( may be manufactured in house ) 112 m. s. shaft ( may be manufactured in house ) bright m.s. round bar ?80mm, 600mm long, stepped ??0mm on 300mm one end 113 pulleys ( for v belt or flat belt ) to fit on 50mm dia. shaft with key slot 114 steel keys ( may be manufactured in house ) to fit with keyslot of shaft & pulley 115 damaged old spur gear to fit 50mm dia. shaft 116 v belt and flat belt to fit on pulley 117 packing gasket ptfe gasket roll small size 118 washer, clutch, keys, jib, cotter & circlip minimum 25mm size, carbon steel material 119 hollow punch straight shank hollow punch sets 5 12mm 120 drill drift ( may be manufactured in house ) 200mm hardened and black finish 121 bearing different types each type of diameter 25mm ( min. ) 122 lifting sling 8mm nominal dia. single leg sling 123 bearing extractor universal gear puller 2 or 3 jaws adjustable 124 pulley extractor universal gear puller 2 or 3 jaws adjustable 125 trammel 300 mm 126 pocker. 127 prick punch 100 mm 128 mallet. dia 100 mm x 150 mm 129 aviation snips straight cut 300 mm 130 flat headed hammers with handle. 131 planishing hammer. 132 snip bent left cut 250 mm 133 stake hatchet with leg. 300 x 200 x 20 mm 134 stake grooving. 100 x 100 x 300 mm 135 slip gauge as johnson metric set. 87 pieces set 136 gauge snap go and not go 25 to 50 mm by 5 mm, set of 6 pieces 137 gauge plug single ended 5 to 55 by 5 mm. set of 11 pcs. 138 gauge telescopic set. 8 150 mm 139 dial test indicator on stand 0.01 mm least count 140 sine bar 125 mm 141 dial verniercaliper. ( universal type ) 0 300 mm, lc 0.05 mm 142 screw thread micrometer with interchangeable. pitch anvils for checking metric threads 60. 0 25 mm lc 0.01 mm 143 depth micrometer. 0 25 mm accuracy 0.01 mm with standard set of extension rods upto 200 mm 144 vernier caliper. 0 150 mm with least count 0.02mm 145 digital micrometer outside. 0 25 mm l.c. 0.001 mm. 146 comparators gauge dial indication with stand and bracket. lc 0.01mm 147 engineers try square ( knife edge ) 150 mm blade 148 surface roughness comparison plates n1 n12 grade 149 digital vernier caliper 0 200 mm l.c. 0.01 mm ( optional ) 150 vernier bevel protector range 360deg, lc. : 5min ( 150mm blade ) 151 carbide wear block. 1 mm 2 mm 152 lathe tools h.s.s. tipped set. 153 lathe tools bit. 6 mm x 75 mm hss / carbide 154 lathe tools bit. 8 mm x 75 mm hss / carbide 155 lathe tools bit. 10 mm x 75 mm hss / carbide 156 arm strong type tool bit holder. right hand 157 arm strong type tool bit holder. left hand 158 arm strong type tool bit holder. straight 159 stillson wrenches 250 mm 160 pipe cutter wheel type. 6 mm to 25 mm 161 pipe bender machine spool type with stand manually operated. up to 25 mm cold bending 162 adjustable pipe chain tonge to take pipes up to 300 mm 163 adjustable spanner. 380 mm long 164 ss and sc centre lathe ( all geared ) with minimum specification centre height 150 mm and centre distance 1000 mm along with 3 & 4 jaw chucks, auto feed system, safety guard, taper turning attachment, motorized coolant system, lighting arrangement & standard accessories. 165 pillar type drilling machine sensitive 0 20 mm cap. with swivel table motorized with chuck & key. 166 drilling machine bench sensitive 0 12 mm cap motorized with chuck and key. 167 d.e. pedestal grinding machine with wheels rough and smooth 2 h.p. 3phase 415v, 1500 rpm, 250 dia. wheel 168 transformer welding set continuous welding current, with all accessories and electrode holder 60% duty cycle with standard accessories 300 a, ocv 60 100 v 169 welder cable able to carry 300 amps. with flexible rubber cover 170 lugs for cable 171 arc welding table ( all metal top ) with positioner. 1200 x 1200 x 750 mm 172 oxy acetylene gas welding set equipment with hoses, oxygen & acetylene cylenders, regulator and other accessories. 173 gas welding table with positioner with fire bricks 900 x 600 x 750 mm 174 welding torch tips of different sizes for oxy acetylene gas welding to fit nozzel no. 1, 2, & 3 175 gas lighter. 176 trolley for gas cylinders. 177 chipping hammer. 178 gloves ( leather ) 179 leather apron. 180 spindle key for cylinder valve. 181 welding torches. nozzles no. 1, 2, & 3 182 welding goggles 183 welding helmet with coloured flame retardent glass 184 tip cleaner 185 compressor unit suitable for pressure: 8 bar, delivery: 50 lpm ( or more ) , reservoir capacity: 24 litres ( or more ) , 230v, 50 hz, with pressure regulator and water separator 186 pneumatic trainer kit, each consisting of the following matching components and accessories: ni. single acting cylinder max. stroke length 50 mm, bore dia 20 mm nii. double acting cylinder max. stroke length 100 mm, bore dia 20 mm, magnetic type niii. 3 / 2 way valve manually actuated, normally closed niv. 3 / 2 way valve pneumatically actuated, spring return v. one way flow control valve nvi. 5 / 2 way valve with manually operated switch nvii. 5 / 2 way valve pneumatically actuated, spring return nviii. 5 / 2 way pneumatic actuated valve double pilot nix. 3 / 2 way roller lever valve direct actuation normally closed nx. shuttle valve ( or ) nxi. two pressure valve ( and ) nxii. pressure gauge 0 16 bar nxiii. manifold with self closing nrv, 6 way nxiv. pushbutton station for electrical signal input with 3 illuminated momentary contact switches ( 1 no + 1 nc ) and 1 illuminated maintainedcontact switch ( 1 no + 1 nc ) , contact load 2a nxv. relay station with 3 ralays each with 4 contact sets ( 3no+1nc or change over type ) , 5 a nxvi. 3 / 2 way single solenoid valve with led nxvii. 5 / 2 way single solenoid valve with manual override and led nxviii. 5 / 2 way double solenoid valve with manual override and led nxix. power supply unit, input voltage 85 – 265 v ac, output voltage: 24 v dc, output current: max. 4.5 a, short circuit proof. nxx. profile plate, anodised aluminium 1100x700 mm, with carriers, mounting frames and mounting accessories ( to be fitted onto the pneumatic workstation ) 187 pneumatic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: n ( 1 ) work table – size ( approx. ) l1200mmxw900mmxh900mm, with four castor wheels including two lockable wheels at the front side, n ( 2 ) drawer – size ( approx. ) – l460mmxw495mmxh158mm each, andoverall size of drawer unit ( approx. ) l470mmxw495mmxh825 mm and n ( 3 ) drawer slide height ( approx. ) 85mm. 188 carrier for mounting components, such as pb & relay boxes. 189 cut section model for pneumatic components 190 hydraulic trainer kit, each consisting of the following matching components and accessories: ni. hydraulic power pack with ( 1 ) external gear pump having a delivery rate of 2.5 lpm, ( approx. ) @ 1400 rpm operating pressure 60 bar, coupled to a single phase ac motor ( 230 v ac ) having start capacitor and on / off switch and overload protection, ( 2 ) pressure relief valve adjustable from 0 – 60 bar, ( 3 ) oil reservoir, =5 litres capacity having sight glass, drain screw, air filter, and p and t ports. nii. pressure relief valve pilot operated niii. drip tray, steel size 1160 mm x 760 mm. niv. pressure gauge glycerin damped, indication range of: 0 – 100 bar nv. four way distributor with five ports, equipped with a pressure gauge nvi. double acting hydraulic cylinder with a control cam, piston diameter16 mm, piston rod diameter10 mm, stroke length 200 mm. nvii. suitable weight for vertical loading of hydraulic cylinder nviii. mounting kit for weight for realizing pulling and pushing load. nix. 3 / 2 way directional control valve with hand lever actuation. nx. 4 / 2 way directional control valve with hand lever actuation. nxi. 4 / 3 way directional control valve closed centre position, with hand lever actuation. nxii. non return valve. nxiii. pilot operated check valve pilot to open. nxiv. one way flow control valve with integrated check valve. nxv. t connector with self sealing coupling nipples ( 2 nos. ) and quick coupling socket ( 1 no. ) . nxvi. profile plate, anodised aluminium, 1100x700 mm, with carriers, mounting frames and mounting accessories ( to be fitted onto the hydraulic workstation ) 191 hydraulic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: n ( 1 ) work table – size ( approx. ) l1200mmxw900mmxh900mm, with four castor wheels including two lockable wheels at the front side n ( 2 ) drawer – size ( approx. ) – l460mmxw495mmxh158 mm each, and overall size of drawer unit ( approx. ) l470mmxw495mmxh825 mm and n ( 3 ) drawer slide height ( approx. ) 85mm. 192 cut section models for hydraulic components 193 caliper outside spring joint 150 mm 194 caliper inside spring joint 150 mm 195 caliper odd leg firm joint 150 mm 196 steel rule 150 mm, graduated both in metric and english unit 197 scriber 150 mm x 3 mm 198 hammer ball peen 250 gm with handle 199 centre punch 100 mm 200 divider spring joint 150 mm 201 safety goggles clear glass ( good quality ) 202 surface plate granite 1000 x 1000 mm with stand and cover 203 work bench 240 x 120x 90cm high 204 marking table ( ci ) 120 x 120 cm 205 bench vice 125 mm jaw 206 v block 150x100x100 mm with clamp ( hardened & ground ) 207 universal surface gauge 250 mm arm 208 hammer ball peen 750 gm with handle 209 chisel cold flat 20 x 150 mm 210 hammer copper / brass 500 gm with handle 211 hacksaw fixed 200 mm ( pistol grip ) 212 file flat 300 mm rough 213 file flat 250 mm 2nd cut 214 file flat 250 mm smooth 215 file round 250 mm smooth 216 file half round 150 mm smooth 217 knurling tool revolving head ( rough, med, fine ) diamond and straight 218 combination set 300 mm ( complete set ) 219 screw driver 10 x 200 mm 220 spanner double ended 6 mm to 21 mm 221 spanner adjustable 200 mm 222 pliers flat nose 150 mm side cutting 223 caliper transfer inside 150 mm 224 micrometer outside 0 to 25 mm, least count 0.01 mm with nabl accredated lab. certificate 225 micrometer outside 50 to 75 mm, least count 0.01 mm with nabl accredated lab. certificate 226 micrometer inside up to 25 to 50 mm, least count0.01 mm with nabl accredated lab. certificate 227 depth gauge micrometer 0 to 150 mm, least count 0.01 mm with nabl accredated lab. certificate 228 vernier caliper outside, inside and depth 200 mm / 8 inches with metric & inch scale ( l.c. = 0.02mm ) with nabl accredated lab. certificate 229 dial vernier caliper with metric 200 mm, least count 0.05 mm with nabl accredated lab. certificate 230 vernier bevel protractor 300 mm blade with nabl accredated lab. certificate 231 vernier micrometer 0 25 mm o / s lc 0.001mm with nabl accredated lab. certificate 232 vernier micrometer 25 50 mm, outside least count 0.001 mm with nabl accredated lab. certificate 233 vernier micrometer 0 inch to 1 inch.outside least count 0.001 inch with nabl accredated lab. certificate 234 gauge radius set 1 mm to 25 mm by 0.5 mm 235 screw pitch gauge whitworth & metric each ( 0.25 to 6mm ) 236 drill angle gauge 237 universal dial test indicator plunger type range 0 10 mm, graduation 0.01 mm complete with clamping devices and magnetic stand 238 vernier height gauge 0 300 mm, lc = 0.02 mm with nabl accredated lab. certificate 239 magnifying glass 75 mm with magnifying factor 10x 240 plain ring and plug gauge ( 12, 16, 20, 25, 30, 32, 36, 40, 45, 50 mm ) 241 wheel dresser huntingon type with star cutter 242 wheel dresser diamond ( inserted 0.75 or 1 carat ) 243 screw thread micrometer interchangeable ( 0 25 mm ) 244 morse taper plug & ring gauge no. 0 to 7 mt 245 sine bar with centers 200 mm 246 slip gauge metric set ( 87 pieces in a box ) with workshop grade 247 morse taper sleeves no. 0 1, 1 2, 2 3, 3 4, 4 5. 248 twist drill straight shank 3 to 12 mm by 1 mm 249 drill twist set taper shank 14 mm to 20 mm by 1 mm 250 drill chuck 12 mm cap with key 251 tap & die b.a. no. 0 to 10 in a box 252 tap and die set metric 3 to 24 mm 253 tap & die b.s.f. up to 1 inch 254 tap & die b.s.w. up to 1 inch 255 reamer machine straight flute 6 to 25 mm 256 reamer adjustable 10 to 20 mm 257 tool holder rh & straight for mm square tool bit 258 parting tool holder with h.s.s. blade 259 tool bits 12 x 150 mm sq. assorted shaped 260 boring tool holder 6 mm sq. tool bit 261 steel rule 300 mm with metric and inch 262 oil can ½ pint ( pressure feed system ) 263 dog carrier 25, 50 and 75 mm 264 angle plate adjustable 150 x 175 x 250 mm 265 spirit level 0.05 mm / 200 mm 266 tool maker’s button 267 combination drill / centre drill a3, a4 & a5 268 oil stone 12 mm sq. x 100 long fine 269 tap wrench ( adjustable ) 270 die handle 271 tool bit assorted sizes on holder 272 chalk board on mobile stand 273 spare grinding wheel ajax type for carbide tool 274 almirah 1980x 910 x 480 mm 275 st. locker with drawer ( pigeon holes ) 276 angle gauge for tool grinding 277 hand chaser m 12 & m 16 ( external ) 278 hand chaser m 12 & m 16 ( internal ) 279 revolving center ( to suit lathe tailstock ) 280 tool cemented carbide assorted shaped external ) for steel turning set of 12 nos. 281 thread plug gauge m 20 & m 21 282 machine chaser m 12 to m 21 ( std. series ) to suit on 283 coventry die head 284 gauge drill grinding 285 magnetic chuck 150 mm dia. ( circular type ) 286 lathe mandrels ( diff. types ) 287 coventry type die head ( self opening ) 288 collapsible tap with attachment 289 fire extinguisher and buckets 290 bore dial gauge stems 12 to 35 mm, 35 to 65 mm., dial gauge indicator of 0.01 accuracy. 291 lathe s.s. & s.c. ( all geared head stock ) with minimum specification as: 150 mm center height, to admit 750 mm between centers. nmachine to be motorized and supplied with coolant installation, 4 jaw independent chuck 150 mm, 3 jaw self centering chuck 150 mm, fixed steady, traveling steady, face plate, driving plate, 4 way tool post, quick change gear box for metric or british threads, live and dead centers with taper attachments, motor capacity 5.5 kw 292 lathe s.s & s.c. ( all geared type ) with minimum specification as: 150 mm. center height, 1000 mm between centers, gap bed machine to be motorized and supplied with coolant installation, 4 jaw independent chuck 250 mm , 3 jaw self centering chuck 200 nmm fixed steady, face plate, driving plate, 4 way tool post, quick change gear box for metric / british threads, live and dead centers with taper attachments, motor capacity 5.5 kw 293 lathe tool room s.s. & s.c. ( all geared type ) with minimum specification as: 150 mm center height, 1000 mm between centers. machine to be motorized and supplied with coolant installation, 4 jaw independent chuck 250 mm, 3 jaw self centering chuck 150 mm fixed steady, traveling steady, face plate, driving plate, 1 way tool post, draw in type collets set up to 25 mm, 0.5 mm, relieving nattachments, motor capacity 5.5 kw 294 grinding machine pedestal type d.e. 200 mm dia. wheel with wheel guard and vision, motor capacity 0.75 kw 295 drill machine pillar type motorized up to 12 mm. cap, motor capacity 0.75 kw 296 power saw machine – hydraulic feed system 400 mm. blade size, motor capacity 0.75 kw 297 cnc lathe / cnc turn centre [ specification as per annex a & a ( i ) ] 298 tool holders [ specification as per annex a & a ( i ) ] 299 digimatic electronic vernier caliper inch and mm 8 / 200 mm. lcm 0.005 / 0.001 mm 300 digimatic electronic outside micrometer ( 0 to 25 mm & 25 to 50 mm ) lc 0.001 mm. 301 steel rule 30 cm graduated both in english & metric units 302 outside spring caliper 150 mm 303 hermaphrodite caliper 150 mm 304 divider spring 150 mm 305 hammer b.p. 0.5 kg 306 cold chisel flat 25 x 200 mm 307 file flat bastard 300 mm 308 combination plier 150 mm 309 safety glasses 310 surface plate 400 mm x 400mm grade 311 marking off table 1200 x 1200 x 600 mm high with stand 312 v block 100 / 7 – 80 – a 313 try square 300 mm 314 outside spring caliper 200 mm 315 divider spring 200 mm 316 inside spring caliper 200 mm 317 straight edge steel 1 meter 318 straight edge steel 500 mm 319 steel tape 2 meter in case 320 steel rule 60 cm graduated both in english & metric units 321 sprit level 2v 250, 05 meter 322 hammer b.p. 800 gms with handle 323 screw driver, heavy duty 300 mm with handle 324 hammer lead 1 kg. 325 spindle blade screw driver 100 mm 326 allen hexagonal keys 2.5 to 12 327 spanner d.e. series 2 ( set of 7 pieces ) 328 adjustable spanner 300 mm 329 reduction sleeve morse 1 1, 3 1, 4 1, 4 2, 5 1, 5 2, 330 angle plate size 200 x 100 x 200 mm 331 angle plate adjustable 250 x 150 x 175 mm 332 oil can pressure feed 500 mg 333 oil stone 150 x 50 x 25 mm 334 number drills h.s.s. ( parallel shank ) 335 punch number set 3 mm 336 twist drills 3 mm to 13 mm in step of 0.5 mm ( parallel shank ) 337 drill chuck 0 13 mm with taper shank 338 centre drill a 1 to 5 339 grinding wheel dresser ( diamond ) 340 grinding wheel dresser huntington type 341 clamps c 200 mm 342 tap and die set in box metric pitch ( 6 mm to 12 mm ) 343 drill h.s.s. taper shank ( 6 mm to 12 mm in step of 0.5 mm ) 344 file half round 2nd cut 250 mm 345 needle file set 346 file square 2nd cut 250 mm 347 reamer 6 mm to 25 mm by 1 mm 348 reamer adjustable 10 mm to 15 mm length 75 mm 349 tool bits h.s.s. 6 mm square 350 tool bits h.s.s. 10 mm square 351 tool bits holder ( armstrong ) l.h 352 tool bits holder ( armstrong ) r.h. 353 assorted tools and bit holders for lathe, shaper, slotter & planner in different shapes and sizes 354 hacksaw frame adjustable 250 300 mm with blades 355 table chuck 75 mm jaw swivel base 356 bench vice 100 mm jaw 357 machine vice 200 mm swivel base 358 machine vice swivel base 150 mm 359 hand vice 50 mm jaw 360 radius turning attachment 361 angle turning attachment 362 compound angle vice ( standard sine ) 363 universal machine vice 100 mm 364 universal table angle plate 150 x 150 x 150 mm 365 shaper tool holder turret type to suit the machine 366 base chuck for slotter to suit the machine 367 shaper indexing center to suit the machine 368 knurling tools ( set of 3 ) straight and diamond 369 plier cutting 200 mm 370 carbide tipped tools of different sizes and shapes ( throw away tips ) 371 hand hammer 1 kg with handle 372 digital multimeter 0 to 500 v 373 variable resistance box resistors with 220o, 150o, 1ko, 33o, 100o, 1.2o 374 dc battery with cap 9v 375 dual power supply ( 230v, 50hz, fuse 800ma ) 376 solder iron ( 350v ) , solder lead, pcb board ( groove board ) , solder wick 377 inductor ( 400 turns, 200 turns, 600 turns, 1200 turns ) , i core , e core, ucore, laminated core 378 relay ( 5v ) , led ( 5v ) 379 function generator ( 230v, 50hz, watts 12va, fuse 150ma ) 380 bread board 381 synchronous motor ( 240v, 60rpm ) , capacitor for synchronous motor ( 0.8mf ± 5% 450 vac ) 382 power chord connecting probes, single strand & multi strand wires. 383 power supply ( 0 30v dc, 3a ) 384 sensor kit ni. mounting plate nii. power distribution box ( 24v dc, 4a ) niii. counter box ( 10 30v dc / 0.05a ) niv. indication box ( 24v dc ) nv. material box nvi. inductive sensor ( 10 30 v dc, pnp, no, 5mm ( range ) ) nvii. capacitive sensor ( 10 30 v dc, pnp, no, 2 8mm ( range ) ) nviii. magnetic sensor ( 10 60 v dc , pnp, no, 60mm ( range ) ) nix. ultrasonic sensor ( 20 30 v dc, pnp, no, 80 300mm ( range ) ) nx. connecting wires nxi. motor with control unit ( 24v dc, 1a ) 385 milling cutter cylindrical cutter ø 63 mm, 90 mm length and 27 mm bore diameter 386 milling cutter cylindrical cutter ø 80 mm, 90 mm length and 27 mm bore diameter 387 milling cutter side and face cutter dia 100 x 10 x 27 mm 388 milling cutter side and face cutter dia 100 x 12 x 27 mm 389 milling cutter side and face cutter dia 160 x 10 x 27 mm 390 milling cutter side and face cutter dia 160 x 16 x 27 mm 391 milling cutter side and face cutter dia 200 x 20 x 27 mm 392 milling cutter side and face cutter dia 80 x 8 x 27 mm 393 milling cutter equal angle cutter 45° / 100 mm x 27 mm bore dia 394 milling cutter equal angle cutter 60° / 100 mm x 27 mm bore dia 395 milling cutter equal angle cutter 90° / 100 mm 27 mm bore dia 396 milling cutter double angle unequal cutter 50 x 12 x 27 mm bore dia55° 397 milling cutter double angle unequal cutter 50 x 12 x 27 mm bore dia 60° 398 milling cutter double angle unequal cutter 63 x 18 x 27 mm bore dia 70° 399 milling cutter double angle unequal cutter 63 x 18 x 27 mm bore dia 75° 400 milling cutter single angle cutter 63 x 18 x 45° rh 27 mm bore dia 401 milling cutter single angle cutter 63 x 18 x 45°lh 27 mm bore dia 402 milling cutter single angle cutter 63 x 18 x 60° lh 27 mm bore dia 403 milling cutter single angle cutter 63 x 18 x 60°rh 27 mm bore dia 404 milling cutter slitting saw cutter ø 75 x 3 x ø 27 mm 405 milling cutter slitting saw cutter ø 100 x 6 x ø 27 mm 406 milling cutter shell end mill ø 50 x 36 x 27 mm, preferably inserted tip type 407 milling cutter shell end mill ø 75 mm x 50 x 27 mm, preferably inserted tip type 408 milling cutter parallel shank end mills ø 6, ø 10 and ø 16 are ( double fluted ) , ø 20 mm & ø 25mm ( four fluted ) 409 milling cutter t slot cutter with parallel shank ø 17.5 x 8 mm width x diameter of shank 8 mm 410 milling cutter concave ø 63 x 6 radius x 27 mm bore diameter 411 milling cutter convex ø 63 x 6 radius x 27 mm bore diameter 412 milling cutter disc type form ( involutes form 2 module, 20° pressure angle ) 413 micrometer outside 0 25 mm reading 0.01 mm with nabl accredited lab. certificate 414 micrometer outside 25 50 mm reading 0.01 mm with nabl accredited lab. certificate 415 micrometer outside 50 75 mm reading 0.01 mm with nabl accredited lab. certificate 416 micrometer outside 75 100 mm reading 0.01 mm with nabl accredited lab. certificate 417 micrometer depth gauge 0 200 mm reading 0.01 mm with nabl accredited lab. certificate 418 digital micrometer 0 25 mm reading 0.01 mm with nabl accredited lab. certificate 419 vernier caliper depth 200 mm / 8 inches with metric & inch scale ( l.c. = 0.02mm ) with nabl accredited lab. certificate 420 direct reading vernier caliper 0 300 ( direct reading with dial ) 421 digital vernier caliper 0 300 mm 422 vernier height gauge q 250 mm 423 vernier gear tooth caliper 424 combination set with 300 mm rule 425 vernier bevel protractor with 150 m blade 426 bevel gauge 200 mm 427 telescopic gauge 8 mm to 150 mm 428 sine bar 200 mm 429 universal dial test indicator plunger type range 0 10 mm, graduation 0.01 mm complete with clamping devices and magnetic stand 430 centre gauge com. 60°, 55° and 29° 431 gauge slip box metric 87 pieces set 432 gauge screw pitch metric 0.25 to 6 mm 433 gauge radius set 1 mm to 25 mm by 0.5 mm 434 limit plug gauges 5 mm to 25 mm by 2.5 mm 435 ring gauges 5 mm to 25 m by 2.5 mm ( go & no go ) 436 taper gauge m.t. no. 1, 2, 3, 4 & 5 437 gauge feeler / thickness 0.05 mm to 0.3 mm by 0.05 and 0.4 mm to 1 mm by 0.1 mm 13 leaves 438 planer gauge standard size 439 steel lockers for 14 trainees 440 steel chair for instructor 441 steel table for instructor 442 work bench 2400 x 1200 x 900 mm 443 steel cup board 180 x 90 x 45 mm 444 steel cup board 120 x 60 x 45 cm 445 slotter 180 mm stroke ( motorized ) with all attachments, motor capacity 0.75 kw 446 ss and sc centre lathe ( all geared ) with specification as: centre height 150 mm and centre distance 1000 mm along with 4 jaw chuck, taper turning attachment, steadies, auto feed system, safety guard, motorized coolant system, with lighting arrangement and set of lathe tools, motor capacity 5.5 kw 447 tool and cutter grinder 250 mm to admit 450 m between center fully motorized work head supplied with tool rest of different types table clamps and other attachments, 3.0kw 448 drilling machine pillar 20 mm capacity with drill chuck & key, 0.75 kw 449 radial drill 1200 mm area motorized with tapping attachment, 3.6kw 450 silicon carbide grinder for carbide tipped tools 451 double ended pedestal grinder with 178 mm wheels ( one fine and one rough wheel ) , 0.75 kw 452 universal milling machine with minimum specification as: table length x width 1200 x 300 mm having motorized up & down movement along with auto feed arrangement and with motor capacity 7.5kw following attachments such as: na. vertical head nb. slotting attachment nc. rack cutting attachment nd. rotary table ne. dividing head nf. adaptors, arbors and collects etc. for holding straight shank drills and cutters from 3 mm to 25 mm. 453 horizontal milling machine with minimum specification as: table length x width 1200 x 300 mm having motorized up & down movement along with auto feed arrangement and 150mm universal vice, motor capacity 7.5kw 454 vertical milling machine with minimum specification as: table length x width 1200 x 300 mm having motorized up & down movement along with auto feed arrangement along with 150mm universal vice, motor capacity 5.5kw 455 surface grinding machine with minimum specification as: grinding machine plain surface, wheel dia. 175 mm ( or near ) with reciprocating table having longitudinal table traverse 200 mm ( or near ) fully automatic and fitted with adjustable traverse stops, machine to be fully motorized and fitted with ace guards and pumps, tank and pump fittings and also to be supplied with magnetic chuck 250 x 112 mm. diamond tool holder, set of spanners, grease gun, oil can and spare grinding wheel for general purpose grinding, motor capacity 3.0 kw 456 cylindrical grinder max. grinding length – 300 mm height of centre – 130 mm max. distance between centers 340 mm 457 cnc vertical machining centre [ specification as per annex a &a ( ii ) ] 458 a ) simulator nb ) desktop computers n [ specification as per annex a &a ( ii ) ] 459 cnc milling tools [ specification as per annex a &a ( ii ) ] 460 cnc hole machining tools [ specification as per annex a &a ( ii ) ] 461 measuring steel tape 5 meter 462 combination plier insulated 200 mm 463 screw driver insulated 4mm x 150 mm, diamond head 464 screw driver insulated 6mm x 150 mm 465 electrician screw driver thin stem insulated handle 4 x 100 mm 466 heavy duty screw driver insulated 5mm x 200 mm 467 electrician screw driver thin stem insulated handle 4mm x 250 mm 468 punch centre 9mm x 150 mm 469 knife double bladed electrician 100 mm 470 neon tester 500 v 471 steel rule graduated both in metric and english unit 300 mm with precision of 1 / 4th mm 472 hammer, cross peen with handle 250 grams 473 hammer, ball peen with handle 500 grams 474 pincer 150 mm 475 c clamp 200 mm and 100 mm 476 spanner adjustable drop forged, ss 150 mm & 300mm 477 blow lamp brass 0.5 ltr 478 chisel cold 25 mm x 200 mm 479 chisel firmer with wooden handle 6 mm x 200 mm 480 allen key alloy steel 1.5 10 mm ( set of 9 ) 481 grease gun 0.5 ltr. capacity 482 bradawl 483 pully puller with 3 legs 150 mm & 300mm 484 bearing puller ( inside and outside ) 200 mm 485 pipe vice cast iron with hardened jaw open type 100 mm 486 scissors blade, ss 200mm 487 scissors blade, ss 150 mm 488 crimping tool 1.5 sq mm to 16 sq mm & 16 sq mm to 95 sq mm 489 wire cutter and stripper 150 mm 490 mallet hard wood 0.50 kg 491 hammer extractor type 250 grams 492 hacksaw frame adjustable 300 mm fixed 150 mm 493 try square 150 mm blade 494 outside calliper 150 mm spring type 495 inside calliper 150 mm spring type 496 divider 150 mm spring type 497 pliers long nose insulated 150 mm 498 pliers flat nose insulated 200 mm 499 pliers round nose insulated 100 mm 500 tweezers 150 mm 501 snip straight and bent heavy duty 250 mm 502 d.e. metric spanner double ended 6 32 mm 503 drill hand brace 0 100mm 504 drill s.s. twist block 2 mm, 5 mm and 6 mm set of 3 505 plane cutters 50 mm x 200mm 506 smoothing cutters 50 mm x 200mm 507 gauge, wire imperial stainlees steel marked in swg & mm wire gauge metric 508 file flat 200 mm 2nd cut with handle 509 file half round 200 mm 2nd cut with handle 510 file round 200 mm 2nd cut with handle 511 file flat rough 150 mm with handle 512 file flat bastard 250 mm with handle 513 file flat smooth 250 mm with handle 514 file rasp, half round 200 mm bastard with handle 515 copper bit soldering iron. 0.25 kg 516 de soldering gun heat proof nozzle, pvc type, 250mm 517 table vice 100 mm jaw 518 contactor & auxiliary contacts 3 phase, 415 volt, 25 amp with 2 no and 2 nc 519 contactor & auxiliary contacts. 3 phase, 415 volt, 32 amp with 2 no and 2 nc 520 limit switch limit switch, liver operated 2a 500v, 2 contacts 521 rotary switch 16 a / 440v 522 relay a. cut out relays 16a, 440v b. reverse current 16a, 440v c. over current 16a, 440v d. under voltage 360v 440v 523 pin type, shackle type, egg type & suspension type insulators including hardware fitting 524 hydrometer 525 hand drill machine 0 6 mm capacity 526 portable electric drill machine 0 12 mm capacity 750w, 240v with chuck and key 527 load bank ( lamp / heater type ) 6 kw, 3ph 528 brake test arrangement with two spring balance rating 0 to 25 kg 529 laboratory type induction coil 1000 w 530 out side micrometer 0 25 mm least count 0.01mm 531 thermometer digital 0° c 150° c 532 series test lamp 230v, 60w 533 knife switch tpdt fitted with fuse terminals 16 amp / 440 v 534 miniature breaker 16 amp 535 earth plate 60cm x 60cm x 3.15mm copper plate 60cm x 60cm x 6mm gi plate 536 earth electrode primary electrode 2100x28x3.25mm secondary cu strip 20x5mm 537 mccb 100amps, triple pole 538 elcb and rccb 25amps, double pole and 25amps, double pole, i?n 30 ma 539 fuses hrc glass rewire type 540 rheostat ( sliding type ) 0 25 ohm, 2 amp 0 300 ohm, 2 amp 0 1 ohm, 10amp 0 10 ohm, 5 amp 541 capacitors electrolytic ceramic polyester film variable dual run 542 various electronic components resistors, diode, transistor, ujt, fet, scr, diac, traic, igbt, small transformer etc. 543 various lamps halogen incandescent lamp fluorescent tube hp mercury vapor lamp high pressure sodium lamp low pressure sodium lamp led 544 plug socket piano switch lamp holder 230 v, 5 a 545 cables : twisted pair non metallic sheathed cable underground feeder cable ribbon cable metallic sheathed cable multi conductor cable coaxial cable direct buried cable 1 mtr each 546 bus bar with brackets 1 mtr each 547 rubber mat 2’ x 4’ x 1” 548 electrician helmet yellow colour 549 rcc pole with accessories ( ms angle iron, ‘c’ clamp, stay insulator etc. ) and materials 6 mtr 550 safety belt standard quality 551 ohm meter; series type & shunt type, portable box type 50 / 2000 ohm analog 552 digital multi meter dc 200mv 1000v, 0 – 10a & ac 200mv 750v , 0 10a, resistance 0 20 mo and 3 1 / 2 digit 553 a.c. voltmeter m.i. analog, portable box type housed in bakelite case multi range 75 v 150v 300v 600v 554 milli voltmeter centre zero analog, portable box type housed in bakelite case 100 – 0 – 100 mv 555 ammeter mc analog, portable box type housed in bakelite case 0 500 ma, 0 5 a, 0 25 a 556 ac ammeter mi, analog, portable box type housed in bakelite case 0 1 a, 0 5 a, 0 25 a 557 kilo wattmeter analog 0 1.5 3kw, pressure coil rating 240v / 440v, current rating 5a / analoge, portable type housed bakelite case 558 digital wattmeter 230 v, 1 kw, 50 hz 559 a.c. energy meter single phase, 10 a, 240 v induction type 560 a.c. energy meter three phase, 15 a , 440 v induction type 561 power factor meter digital 440 v, 20 a, three phase portable box type 562 frequency meter 45 to 55 hz 563 magnetic flux meter 0 500 tesla 564 lux meter lux meter lcd read out 0.05 to 7000 lumens with battery. 565 tachometer analog type 10000 rpm 566 tachometer digital photo sensor type 10000 rpm 567 tong tester / clamp meter 0 100 a ( digital type ) 568 megger analog 500 v 569 3 point d.c. starter for 2.5 kw dc motor 570 4 point d.c. starter for 2.5 kw dc motor 571 wheat stone bridge with galvanometer and battery 572 single phase variable auto transformer 0 270 v, 10amp ( air cooled ) 573 phase sequence indicator 3 phase, 415 v 574 growler 230 v, 50 hz, single phase, adjustable jaws, testing armature with ampere meter and testing probes. 575 ac starters: na. resistance type starter nb. direct on line starter nc. star delta starter manual nd. star delta starter – semi automatic ne. star delta starter – fully automatic nf. star delta starter soft starter ng. auto transformer type for a.c motors of 2 to 5 h.p. 576 oscilloscope dual trace 20 mhz 577 function generator 2 to 200 khz, sine, square, triangular 220 v, 50 hz, single phase 578 soldering iron 25 watt, 65 watt and 120 watt, volt 579 temperature controlled soldering iron 50 watt, 230 volt 580 discrete component trainer discrete component ( for diode transistor circuit ) with regulated power supply +5, 0 5 v, +12 , 0 12 581 linear i.c. trainer linear i.c. trainer with regulated power supply 1.2v to 15v pic socket 16pin and 20 pin with bread board 582 digital i.c. trainer digital i.c. trainer 7 segment display and bread board 583 domestic appliances – na. electric induction plate a. 1500 watt, 240v nb. electric kettle b. 1500 watts, 240v nc. electric iron c. automatic 750 w, 240 v nd. immersion heater d. 1500 watt, 240v ne. a.c. ceiling fan and ac table fan e. 68 watt, 230 v nf. geyser ( storage type ) f. 10 litre ng. mixture & grinder g. 750 w, 240 v nh. washing machine semi automatic h. 5 kg, ni. motor pump set i. 1 hp, 1 phase, 240 v 584 oil testing kit oil testing kit 230 v, single phase 50 hz 60 va output 0 60 kv variable 585 inverter with battery 1 kva with 12 v battery input 12 volt dc, output 220 volt ac 586 voltage stabilizer ac input 150 250 v, 600 va ac output 240 v, 10 a 587 dc power supply 0 30 v, 5 a 588 current transformer 415 v, 50hz, ct ratio 25 / 5 a, 5va 589 potential transformer 415 v, 50hz, pt ratio, 440v / 110v, 10va 590 solar panel with battery 18 watt 591 pentium iv computer or latest 2.8 ghz & above, 1 gb ram, 80 gb hdd, dvd combo drive, 19 / 21” monitor, optical scroll mouse, multimedia key board, 32 bit lan card with upp port, necessary drivers, etc. or ( latest version ) 592 ink jet / laser printer 593 d.c. shunt generator with control panel d.c. shunt generator with control panel, 2.5 kw, 220v &3phase squirrel cage induction motor, 5hp, 440v with control panel & star delta starter 594 motor generator ( ac to dc ) squirrel cage induction motor with star delta starter and directly coupled to dc shunt generator and switch board mounted with regulator, air breaker, ammeter, voltmeter, knife blade switches and fuses, set complete with case iron and plate, fixing bolts, foundation bolts and flexible coupling. induction motor rating: 7.5 hp, 415v, 50 cycles, 3 phase. dc shunt generator rating: 5 kw, 440v ( output voltage varies 110 440v ) 595 d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker, 2.5 kw, 220v &3phase squirrel cage induction motor, 5hp, 440v, with control panel & star delta starter 596 dc series motor coupled with spring balance load 2.5 kw, 220 volts 597 dc shunt motor 2.5 kw, 220 v 598 dc compound motor with starter and switch 2.5 kw , 220 volts 599 motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. shunt motor rating : 5 hp, 440v ac generator rating : 3 phase, 4 wire, 3.5 kva, 400 / 230 volts, 0.8 pf, 50 cycles 600 ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse with mechanical load. 5 hp, 3 phase, 415 v, 50 hz 601 ac phase wound slip ring motor with starter switch 5 hp, 440 v, 3 phase, 50 hz 602 universal motor with starter / switch 240 v, 50 hz, 1 hp 603 synchronous motor with accessories like starter, excitation arrangements. 3 phase, 3 hp, 440v, 50hz, 4 pole 604 thyristor / igbt controlled d.c. motor drive with tacho generator feedback arrangement 1 hp 605 thyristor / igbt controlled a.c. motor drive with vvvf control 3 phase, 2 hp 606 single phase transformer, core type, air cooled 1 kva , 240 / 415 v, 50 hz 607 three phase transformer, shell type oil cooled with delta / star 3 kva , 415 / 240 v, 50 hz 608 electrical machine trainer – suitable for demonstrating the construction and functioning of different types of dc machines and ac machines ( single phase and three phase ) . should be fitted with friction brake arrangement, dynamo meter, instrument panel and power supply unit 609 diesel generator set with change over switch, over current breaker and water / air cooled with armature, star delta connections ac 3 phase 7.5 kva, 415 volt or higher rating 610 used dc generators series, shunt and compound type for overhauling practice 611 pillar electric drill machine motorized 12 20 mm capacity, 1hp, 440v, 3 phase, induction motor with dol starter, bench type 612 motorised bench grinder 1 hp. 3 phase, 440v with dol starter, double side with smooth and rough wheel with tool base 613 a.c. series type motor 1 hp, 240 v, 50 hz 614 single phase capacitor motor with starter switch 1 hp, 240 v, 50 hz 615 manual motor coil winding machine with step arbor 616 primary current injection set 220v, 50 hz, 1 ?, output current 200 a ( min ) with timer 617 stepper motor with digital controller 618 shaded pole motor fractional hp, 240 v, 50 hz 619 working bench 2.5 m x 1.20 m x 0.75 m 620 wiring board 3 meter x1 meter with 0.5 meter 621 projection on the top 622 metal rack lockers with drawers 100cm x 150cm x 45cm 623 almirah 2.5 m x 1.20 m x 0.5 m 624 black board / white board ( minimum 4x6 feet ) 625 fire extinguisher co2 2 kg 626 file flat rough double cut 200mm 627 file, half round, fine double cut, length 150mm 628 file, round, fine double cut length 150mm 629 file flat, fine double cut, length 150mm 630 file square, fine double cut, length 150mm 631 file triangular fine double cut length 150mm 632 scriber 150mm length 633 centre punch length 100mm 634 divider spring joint length 150mm 635 caliper spring joint in side length 150mm 636 caliper, odd leg, spring joint length 150mm 637 hammer ball pane 220 gms 638 cold chisel flat and cross cut length 150mm 639 engineers rule 300mm long 640 tape measuring 10m graduation in mm 641 pliers combination insulated length 200mm 642 pliers long nose 200 mm 643 line tester 500 v heavy duty 644 tweezers 10 cm 645 surface plate 45 x45 cms 646 oil can 500 ml 647 surface gauge universal 150 mm 648 bench vice 150 to 300 mm jaw 649 hack saw tubular metal frame adjustable 300mm 650 snip sheet metal straight nose 200 mm 651 snip sheet metal curved nose 200 mm 652 anvil 100x200mm 653 stakes [ different types ] 100mm 654 tin smith 400mm 655 wooden mallet / nylon mallet 500 gm good finish 656 round punch 3mm, 4mm, 6mm 657 electrical drill portable drill with chuck and key capacity 6.4mm 658 screw driver, plastic handle, 6mm tip length 100mm to 150mm 659 screw driver, plastic handle, flat tip 10mm tip length 200mm & 250mm 660 philips screw driver complete set in leather case 661 screw driver, plastic handle, flat tip handle 3mm tip length 100mm to 150mm insulated 662 soldering iron exchangeable copper tip 65 watts 663 knife folded stainless steel 150mm 664 tong tester ( clamp on multi meter ) 0 10 30 amps 0 500 v 665 tenon saw 250 mm 666 firmer chisel 6, 12, 25mm 667 rawal plug tool 6 mm 668 fire extinguisher abc dry powder type 2 kg capacity 669 fire buckets 10 litre 670 d.e spanner 6 32 mm 671 ring spanner 6 32 mm 672 quick couples, process tube adopter ¼” & 3 / 8” 673 tong close mouth and pick 674 welding table for gas / arc 1200x760 675 flaring tool set, single type for tube. 4.7mm to 16mm o.d 676 swaging tool, punch type, set of size for tube. 4.7mm to 16mm o.d 677 bending spring external type, for copper tube 3mm to 16mm dia 678 pipe cutter miniature for copper tube 3mm to 16mm dia 679 pinch of tool, for copper tube, 6mm to 18mm dia 680 ratchet spanner 6.4 sq.mm reversible 681 capillary plug gauge 682 piercing pliers & reversing valve with access fitting 6 18mm 683 spanner double ended 4.7mm to 16mm 684 ring spanner off set 4.7mm to 16mm 685 wrench adjustable length 150mm 686 wrench adjustable length 200mm 687 wrench adjustable length 250mm 688 valve key handle [ treated as consumable ] 4.7mm & 6.4mm sq. 689 ( hollo ) punch hole for cutting gasket 4.7 16mm die 690 scissor, gasket cutting stainless steel length 25mm 691 l allen key set size 1.5mm to 6.4mm 692 t allen key set size 5 / 32 to 1 / 8 693 pipe cutter with built in reamer and space cutter, for copper tube 3mm to 32mm 694 pipe / tube bender lever type 3 16 mm 695 spanner double ended 19mm to 31.8 mm 696 pipe wrench size 50mm to 150mm 697 lapping plate 250mm x 200mm 698 hammer ball peen 450 gms 699 puller 3 legged with flexible arm 300mm 700 hand blower portable complete 1 / 10 hp 701 spirit level precision metallic 200mm 702 tap set with matching drills 3 mm to 16mm 703 tap set with matching drills v to 5 / 8 704 refrigerant cylinder 2.5 kg 705 heating kit with infrared bulb ( 200 w capacity ) 706 plumbing hammer weight 200 gm 707 cylinder 134 a 5 kg 708 torque wrench 300mm 12.7mm 709 piercing valve ¼ inch 710 feeler gauge 0.05mm to 1mm 711 four way reversible valve 712 vernier hight gauge 300mm , lc 0.02 713 tape measuring graduation in mm 2 m 714 voltmeter, ac / dc portable precision grade digital panel board type 0 to 500 volt 715 ammeter, ac / dc portable precision grade digital panel board type 0 to 30 amp 716 megger 1000v 717 wattmeter multi range up 1 kw 718 multi meter digital type 719 k.w. meter 0 1 k w 720 service oscillator 721 c.r.o single beam 5 mhz 722 c.r.o dual trace / double beam 60 mhz 723 a.f. o oscillators 724 pres sure gauge digital type diameter 63mm with recalibration set 725 compound gauge, digital type diameter 63mm, with recalibration set screw, scale vacuum 760mm. pressure 15 kg / sq.cm 726 service man thermometer in metal case 300c to +1100 c 727 gas leak detector for halogen gas 728 electronic leak detector 729 sling psychro meter mounted on aluminum back, scale 100 c to +1100 c 730 stop watch 731 vernier caliper length 250mm 732 micrometer outside measurement 0 to 25mm 733 multi meter analogue type 734 tachometer digital, multi range 0 r m p to 3000 r m p. portable small size in leather case 735 micron vacuum gauge capable of reading up to 20 microns 736 sensor thermometer ( digital ) 50 degree celsius to150 degree celsius 737 fin straightened / fin comb. with strong steel wire based combing on wood 738 filler gauge 0.05 mm 1 mm 739 wire gauge metric & british. steel plate embossing converse of british & metric 740 dial thermometer remote control, armored capillary dial 75mm 50c to +50 c 741 anemometer digital type 742 compressors testers for small hermetic compressors fixed with electrical input / output indicating facilities 743 digital thermometer graduated disc analogy type 744 temperature &humidity recorder capacity to record 24 hrs record 745 instrumentation screw driver set 100mm 746 digital weighing machine 100 kg 747 split phase induction motor 1hp, 230 v 748 bldc motor with controller 15 – 30 watts, 315 volt dc 749 idu pulse generation type motor 15watt, 230volt a.c 750 capacitor start induction motor 1 hp, 230 v 751 ac 3 phase motor, 400 / 50 hz 2 hp 752 star delta starter 2 hp 753 auto transformer starter 3 hp 754 d.o .l starter 2 hp 755 portable air lpg brazing kit 2 kg. lpg cylinder, torches, houses, stand make 756 oxy acetylene welding set complete cylinders, regulators welding torches with difference nozzles 757 single door direct cool refrigerator, carrying with hfc and hc 185 l 758 fros t free refrigerator 200l carrying with hc blend 759 three / four door refrigerator ( inverter type ) 300l carrying with hc r 600a 760 core drill machine. 761 bench drilling machine 20 mm capacity, 200 2500rpm 762 grinding machine 200mm, 3000rpm, double ended 1 / 2 hp 763 evacuating and refrigerant charging station, consist of na ) rotary two stage vacuum pump and motor ( with gas ballast and anti such back ) nb ) manifold with gauges and valves and capable of pulling vacuum up to 50 microns of hg and with provision of connecting to a microns level vacuum gauge nc ) graduated charging cylinder with provision for temperature correction and all necessary isolating valves n ( cap. 2 kg. in lieu of ( b ) above and with accuracy of + / g for charging hydrocarbons ) 764 evacuating and charging station as above but fitted with weighing scale 765 two stage rotary vacuum pump, 3or 4 cfm. capacity approx. 60 10rmp capable of evacuating to 50 microns of hg and fitted with gas ballast, anti such back valve and single phase motor 766 dry n2 cylinder 2 stage regulator or commercial n2 in cylinder with drier unit and 2 stage regulator & meter cube 767 window a.c 1 ton with r 22 blend reciprocating compressor 768 split a.c 1.5 ton with r134a or r 22 reciprocating compressor 769 ductable split a.c 1.5 ton 1.5 ton with r134a or r 22 reciprocating compressor 770 recovery unit with cylinders cfc, hfc & hcfc 771 decibel meter 30 100 db 772 cassette air conditioner 4500 kcal / hr 773 descaling pump set with stainless steel impeller and housing complete with motor 1 / 2 hp and accessories 774 fan coil unit with water valves ( 2 & 3 way ) 775 shell and tube, dx chillers ( small ) 5 ton with cu tubing only 776 circulating water pump ( small ) 0.5 h.p with stainless steel tank capacity 20 liters within let / outlet provision. 777 refrigerant cylinder 10 kg capacity 778 gauge manifold with gauges different size of hoses for r 134a, r22 and r 410. 779 shell and tube type condenser 5 ton 780 rotary hermetic compressor 2 ton 781 bottle cooler visible 200 l carrying with hfc 134a& reciprocating compressor 782 deep freezer 200 l carrying with hfc 134a& reciprocating compressor 783 display cabinet 2 ton capacity 784 water cooler storage type 200 l carrying with hfc 134a& reciprocating compressor 785 water dispenser bubble type ( hot and cold ) 2.5 to 3ltr. delivery capacity per hour 786 ice candy plant 2 ton with capacity to make 32 ice candy at a time with forma tray, stainless steel tank on trolley 787 air conditioning, direct system. complete with all controls including humidity control 788 air conditioning, indirect system. ( water cooled ) complete with all controls including humidity control 789 package a / c 5 ton capacity, air cooled type with open type compressor reciprocating type 790 car a.c components ( full kit ) na ) wobble plate compressor with mounting brackets. nb ) serpentine evaporator nc ) parallel flow condenser nd ) hoses, tubes, receiver, ex. valve. ne ) electrical components & wiring harness 791 car ac tutorial model 792 bus ac tutorial model 793 auto matic ice cube m / c 50 kg / hour 794 storage type water cooler ( hot and cold ) 795 visi cooler 185 l 796 vrf / vrv unit with two indoor units 2.5tr each and 5tr capacity out door unit complete with air cooled condenser, accessories and controls. 797 split a / c ( inverter technology ) 1.5 tr 798 walk in cooler puf insulated for cold room 6x4.5x8 cft. temperature 00 50 c 799 absorption system small size 800 class room table one table for each trainee size of 2.5 provisions with open rack. frame square conduit of1.top sun mica ply board 801 work bench 2000 x1000 x 700 mm with 2 pipe frame. top with teak slab and fixing with3 / 4 good quality rubber sheet. 802 almirah 195 x90 x 48 cm outer sheet 20 swg inner partition with four selves of 22swg 803 lockers 195 x 90 x 48 set six locker in one structure 804 glas s board portable 2.5x4 with stand 805 instructor table 4x2x2.5 with steel tubular frame & sun mica top 806 inst ructor chair standard revolving with wheel 807 computer table standard with drawers & self to accommodate ups&cpu 808 computer chair revolving type metal based & metal wheel standard one 809 white board 4x3 ferrous base sheet to hold magnetic duster with white finish surface. 810 chart stand 6x3 providing with hanging clip top & bottom plate 811 computer with printer and scanner latest configuration 812 lcd projector / led / lcd tv big size 813 laptop latest version 814 ups 2 kva 815 copier machine. 816 interactive board latest version 817 stoo l 2’ x 1.5’ 818 book self with glass panel 6’ x 3’ 819 stor age rack 6’ x 3’ 820 stor age shelf 6’ x 3’ 821 box drawing instrument containing one 15 cm compass with pin point, pin point & lengthening bar, one pair spring bows, rotating compass with interchangeable ink and pencil points, drawing pens with plain point & cross point, screw driver and box of leads. ( 0.2, 0.3, 0.4 mm ) . 822 protractor celluloid 15 cm semi circular. 823 scale card board metric set of eight a to h in a box 1: 1, 1:2, 1:2:5, 1: 5, 1:10, 1:20, 1:50, 1:100, 1:200, 1:500, 1:1000, 1:2000, 1:1250, 1:6000, 1:38 1 / 3, 1:66 2 / 3 824 scales plotting box wood 6 metric scales 30 cms long withoffset scales. 825 set square transparent 20 cm, 2 mm thick with bevelled edges 45 degree . 826 set square celluloid 25 cm, 2mm thick with bevelled edges60 degrees. 827 t square 750mm / mini drafter / parallel bar 828 template –architects and builders 829 geometrical models ( wooden / plastic ) i ) cube 08 cm sides. ii ) rectangular parallel piped 8cm x 15cm iii ) sphere 8cm dia. iv ) right circular cone 8 cm dia base and 15 cm vertical height v ) square pyramid 8cm side base and 15 cm vertical height vi ) cylinder 8 cm dia. 15 cm height. vii ) prisms triangular 8 cm sides triangle and 15 cm length. viii ) prism hexagonal 8 cm side’s hexagon and 15 lengths 830 templates – circle, ellipse, furniture, etc. 831 french curves transparent plastic set of 12 832 flexible curves 80 cm long 833 radius curve metric 3 mm to 15 mm 834 brass parallel rulers in a case 835 calculator scientific ( nonprogrammable ) 836 proportional dividers 15 cm 837 land measuring chain 30 metres with two handles 838 steel tape 30 meters long in a leather case 839 ranging rod wooden fitted iron shoe 2 mt. long 840 steel arrow, wooden peg, wooden mallet, hammer 841 prismatic compass with stand 110 mm dia. 842 plane table with stand with accessories – alidade, trough compass, spirit level ( 6 ) , u – fork, plumb bob, etc 843 telescopic alidade 844 dumpy level with all accessories 845 auto level with all accessories 846 levelling staff 4 mt. leading to 5 mt. telescopic type 847 transit theodolite with stand with all accessories 848 digital theodolite latest model with all accessories ( features: based on laser technology, two large lcd panel with easy to read , automatically compensates tilt in two direction and compensates vertical angles. high integrated electronic board and ic elements ) 849 instrument for total station with latest model, with all accessories graphic lcd display on both side.multy function key board on both side. able to interchange data between gps and total station without any data conversion. minimum 8 hours rechargeable li ion battery .poles and prism 2nos each 850 hand held gps ( latest model ) with standard specification 851 personal computer with latest configuration min. 19 inch led screen and graphic card with latest operating system. 852 cad software 853 plotter a1 size 854 printer ( a3 laser jet ) with scanner ( multipurpose ) 855 server work station with latest configuration 856 ups 5 kv with 30 min. back up for 24 pc 857 furniture for server, printer, plotter 858 dlp projector 2000 lumens or higher 859 screen for projector motorized 860 document camera / visualiser 861 smart board / inter active board 862 trainer’s / instructor’s table ( big size full secretariat ) 6 x 4 feet 863 trainer’s / instructor’s table 864 chair for trainer / instructor 865 class room chairs ( armless ) 866 class room table single / dual desk 867 almirah steel ( major ) 6” / higher 868 drawing table with board 750mm x 550mm 869 draughtsman drawing instrument box containing compasses with pencil point, point driver, interchangeable, divider pen point interchangeable, divider spring bow, pen spring bow lengthening bar, pen drawing liner, screw driver instrument, tube with lead. 870 set square celluloid 45° 250 x 1.5 mm 871 set square celluloid 30° 60° 250 x 1.5 mm 872 french curves ( set of 12 celluloid ) 873 mini drafter 874 chest of drawer 8 drawers ( standard ) 875 draughtsmanstool 876 desktop computer latest version compatible for running cad software, preloaded with windows and 20” colour monitor. 877 sever ( true dedicated sever ) 878 software: ms office latest version, cad with latest licensedversion, [ optional: latest version of solidwoks, autodesk inventor, catia & pro e ( creo 2 ) ] 879 plotter ( max. a0 size ) 880 laser jet printer latest model 881 white board for using lcd projector ( optional ) 882 table for server, printers 883 lcd projector / ohp 884 external storage device ( 8 gb ) 885 connecting screwdriver 1 0 x 1 0 0 mm 886 neon tester 500 v. 5 0 0 v 887 screw driver set set of 7 888 insulated combination pliers 150 mm 889 soldering iron 25 watt, 240 volt 890 electrician knife 1 0 0 mm 891 soldering iron changeable bits 15 watt, 240 volt 892 de soldering pump electrical heated, manual operators 230 v, 40 w 893 tweezers – bend tip 894 steel measuring tape 3 meter 895 tools makers vice 100mm ( clamp ) 896 tools maker vice 50mm ( clamp ) 897 crimping tool ( pliers ) 7 in 1 898 magneto spanner set 8 spanners 899 file flat second cut 200 mm 900 plier flat nose 150 mm 901 round nose pliers 100 mm 902 hammer ball pen 500 grams 903 allen key set ( hexagonal set of 9 ) 1 12 mm, set of 24 keys 904 tubular box spanner set 6 32 mm 905 hacksaw frame adjustable 300 mm 906 chisel cold flat 10 mm x 150 mm 907 scissors 200mm 908 handsaw 450mm hand saw 450 mm 909 first aid kit 910 dual dc regulated power supply 30 0 30 v, 2 amps 911 dc regulated variable programmable dc power supply 0 30v / 3a 912 lcr meter ( digital ) handheld 913 cro dual trace 20 mhz ( component testing facilities ) 914 signal generator with digital display for frequency amplitude 10 hz to 100 khz, 50 / 600 ohms ( output impedance ) 915 battery charger 0 6 9 12 24 48 v, 30 amp 916 analog multimeter 917 clamp meter 0 10 a 918 function generator ( dds technology ( sine, square, triangle, ramp, pulse, serial data, ttl and modulation. ) 1 mhz 10 mhz function pulse – modulation generator with built in 40mhz frequency counter 919 dimmer starter 3 amps 920 autotransformer 15 amps 921 analog component trainer breadboard for circuit design with necessary dc / ac power supply: sine, square, triangle modulating signal generator and simulation software 922 milli ammeter ( ac ) 0 – 200 ma 923 milli ammeter ( dc ) 0 – 500 ma 924 op amp trainer 925 digital ic trainer breadboard for circuit design with necessary dc power supply, graphical lcd, clock frequency 4 different steps, data switches: 8 nos, led display: 8 nos. ( ttl ) , seven segment display, teaching simulation software 926 digital ic tester 927 digital and analog bread board trainer dc / ac power supply, sine / square / ttl generator data switches, led indication, led display: 8 in nos simulation / teaching content through software 928 rheostats various values and ratings 929 power electronics trainer with at least 6 no’s of application board mosfet characteristics scr characteristics scr lamp flasher scr alarm circuit series inverter single phase pwm inverter 930 computers in the assembled form ( including cabinet, motherboards, hdd, dvd, smps, monitor, kb, mouse, lan card, blu ray drive and player ) , ms office education version. 931 electronic circuit simulation software with 6 user licenses circuit design and simulation software with pcb design with gerber and g code generation, 3d view of pcb, breadboard view, fault creation and simulation. 932 different types of electronic and electrical cables, connectors, sockets, terminations. 933 different types of analog electronic components, digital ics, power electronic components, general purpose pcbs, bread board, mcb, elcb 934 soldering & de soldering station 935 smd soldering & de soldering station with necessary accessories 936 frequency modulator and demodulator trainer kit fm modulator type : reactance modulator, varactor modulator, vco based modulator fm demodulator type all 5 demodulation techniques detailed teaching and learning contents through software. 937 pam, ppm, pwm trainer kit 938 am / fm commercial radio receivers 939 microcontroller kits ( 8051 ) along with programming software ( assembly level programming ) core 8051, ready to run programmer for at89c51 / 52 & 55, programming modes key pad and pc circuits. detailed learning content through simulation software. 940 sensor trainer kit containing following sensors n1. thermocouple n2. rtd n3. load cell / strain gauge n4. lvdt n5. smoke detector sensors n6. speed sensor n7. limit switch n8. photo sensors n9. optocouplor n10. proximity sensor ngraphical touch lcd with inbuilt processor for viewing the output waveforms, in built daq, and standard processing circuits like inverting , non – inverting , power, current , instrumentation differential amplifier, f / v, v / f, v / i, i / v converter, sensors :rtd, ntc nthermistor, lm35 thermocouple, gas ( smoke ) sensor, load cell, lvdt sensor, speed sensor 941 various analog and digital ics useful for doing project works mentioned in the digital and analog ic applications modules 942 different types of electronic and electrical cables, connectors, sockets, terminations. 943 fiber optic communication trainer full duplex analog & digital trans receiver with 660nm & 950nm, noise generator with variable gain, four seven segment display ber counter, eye pattern. 944 seven segment dpm trainer 945 lcd based dpm 946 smps of different make 947 ups trainer pwm switching technology, test points to measures the voltages of different sections overall functioning of ups trainer, avr transformer, ups with load condition 948 mobile phone trainer 2g / 3g / 4g dual sim gsm handset. frequency measurement and band verification. real time mobile operation 949 smart phones of different make ( android / windows ) 950 cell phone power source with charger chords for different cell phones 951 lcd tv ( trainer kit ) 21 inch full hd lcd color television should support pal / ntsc video formats complete block diagram of a lcd tv system, study board indicating various sections of lcd tv along with the test points and switch faults 952 lcd tv ( 21” ) 953 led tv ( trainer kit ) 20 inch full hd led color television, pal / ntsc video formats, complete block diagram of a led tv system , study board indicating various sections of led tv along with the test points and switch faults trouble shooting in different sections. 954 home theatre system 955 solar training kit / simulator with built in meters for dcv, dca, ac multifunction meter ( for aci, acv, power, frequency ) , protection circuits, bs 10 terminals for making the connection, single / dual axis tracking system charge controller : pwm based mppt, charging stage : bulk, absorptions and float 956 led lighting system measurement of power, voltage, current, power factor and light output performance of different lighting products like led, cfl at variable input voltages 0 to 245v variable ac 957 lockers with 16 drawers standard size 958 steel almirah 2.5 m x 1.20 m x 0.5 m 959 soldering iron 25 watt, 240 volt 960 digital multi meter ( 3 3 / 4 digit ) , 4000 counts 961 de soldering pump electrical heated, manual operators 230 v, 40 w 962 file flat bastard 200 mm 963 file flat smooth 200 mm 964 round nose pliers 100 mm 965 hand drill machine electric with hammer action 13 mm 966 dc regulated variable programmable dc power supply 0 30v / 3a 967 signal generator with digital display for frequency amplitude 10 hz to 100 khz, 50 / 600 ohms ( output impedance ) 968 battery charger 0 6 9 12 24 , 15 amps 969 analog component trainer breadboard for circuit design with necessary dc / ac power supply: n? 8 pin zif socket n? 16 pin zif socket n? resistor bank n? capacitor bank n? potentiometers n? diodes n? zener diodes n? npn transistor n? n channel mosfet n? led n? bread board n? ready to use experimental boards lab manual with list of experiments to perform various experiments 970 op amp trainer ? ±15v, ±12 and +5v fixed dc power supply n? 8pin zif socket n? 16 pin zif socket n? resistor bank n? capacitor bank n? potentiometers n? bread board n? built in oscillator : sine, square and trianglular waveform 971 digital ic trainer breadboard for circuit design with necessary dc power supply, graphical lcd, clock frequency 4 different steps, data switches: 8 nos., led display: 8 nos. ( ttl ) , seven segment display, teaching simulation software 972 digital and analog ic tester 973 power electronics trainer with at least 6 nos. of application board mosfet characteristics scr characteristics scr lamp flasher scr alarm circuit series inverter single phase pwm inverter 974 laptops latest configuration 975 different types of electronic and electrical cables, connectors, sockets, terminations. 976 different types of analog electronic components, digital ics, power electronic components, general purpose pcbs, bread board, mcb, elcb 977 dso ( colour ) 4 c hannel , 50mhz real time sampling 1g samples / sec, 12 mpts memory with pc interface usb, lan and math function includes +, , fft, differential, integral, abs, log etc. 978 smd soldering & de soldering station with necessary accessories nsmd rework station nsoldering station: noutput voltage: 26v – 40v ac temp range : 50 to 4800 c ndesoldering station: noutput voltage : 24v – 40v ac nvacuum generator: nvacuum pump: double cylinder type vacuum pressure : 80 k pa suction flow: 15 l / min. nhot air station: nair flow: 1 9 l / min temp:50 o 500 °c hand piece of hot air accessories 979 dol starter ½ hp 980 ac motor trainer kit n¼ hp motor single phase ncontactors nrelays nmcb ndol starter 981 pam, ppm, pwm trainer kit with on board function generator analog inputs in 4 steps 1 10 hz, 10 100, 100 1khz, 10khz analog input voltage variable from 0 to 12 v built in square wave pulse 982 microcontroller kits ( 8051 ) along with programming software ( assembly level programming ) core 8051, ready to run programmer for at89c51 / 52 & 55, programming modes key pad and pc circuits. detailed learning content through simulation software. 983 application kits for microcontrollers 6 different applications n1. input interface : 4x4 matrix keypad, ascii key pad, four input switch n2. display module 16x2 lcd, seven segment, led bar graph n3. adc / dac module with most popular dc / dac0808 n4. pc interface: rs232 & usb n5. motor drive: dc, servo, stepper n6. daq: data acquisition to sense different sensors signals 984 sensor trainer kit containing following sensors n1. thermocouple n2. rtd n3. load cell / strain gauge n4. lvdt n5. smoke detector sensors n6. speed sensor n7. limit switch n8. photo sensors n9. opto coupler n10. proximity sensor ngraphical touch lcd with inbuilt processor for viewing the output waveforms, in built daq, and standard processing circuits like inverting , non – inverting , power, current , instrumentation differential amplifier, f / v, v / f, v / i, i / v converter, sensors: rtd, ntc thermistor, lm 35 thermocouple, gas ( smoke ) sensor, load cell, lvdt sensor, speed sensor 985 different types of electronic and electrical cables, connectors, sockets, terminations. 986 precision set of screw drivers t5, t6, t7 987 smps of different make 988 ups trainer pwm switching technology, test points to measures the voltages of different sections overall functioning of ups trainer, avr transformer, ups with load condition 989 ups 3 kva with backup time minimum 30 minutes 990 allen key screw driver 5 no. of set 991 cctv set up dvrcameras with amplifier set up 992 washing machine auto and semi automatic 993 vacuum cleaner portable and industry model 994 microwave oven 20 liters ( two technologies ) 995 mixer cum grinder 996 steam iron automatic automatic and automatic with steam 997 electric rice cooker 998 water purifier ( ro and uv technologies ) 999 immersion heater 2 kva 1000 induction cooktop induction cook top with following feature: nsafety sensor nauto switch off nauto heat up nbooster nprotection against overflows 1001 printers dmp, laser, deskjet 1002 l ed / lcd projector 1003 dth with accessories 1004 sat meter 1005 co axial cable cutter 1006 lcd tv 21” screen smart tv, with different inputs ( hdmi, vga, component video etc. ) 1007 jacket stripper / coring tool for 500 series cable 1008 centre conductor cleaner 1009 universal drop trimmer for rg 6 / 11 cables 1010 f connector tool for rg 6 / 11 cables 1011 f – connector compression tool for rg 6 / 11 cables 1012 led tv 21” screen smart tv, with different inputs ( hdmi, vga, component video ) 1013 black board / white board 12’ x 4’ 1014 classroom furniture ( dual desk ) 1015 lab tables ( work bench ) 1016 stools for lab 1017 connecting screwdriver 100 mm 1018 screw driver set set of 5 1019 insulated side cutting pliers 150 mm 1020 long nose pliers 150 mm 1021 soldering iron 25 w. 240 v 1022 tweezers 100 mm 1023 digital multimeter 1024 de soldering pump 1025 crimping tool ( pliers ) 1026 scriber straight 150 mm 1027 soldering iron 240 w 1028 allen key set set of 9 1029 magnifying lenses 75 mm 1030 continuity tester 1031 soldering iron 10 w 1032 cold chisel 20 mm 1033 server computer 1034 desktop computer 1035 intel mobile desktop based pc with lcd monitor 1036 tablet 1037 printers: laserjet, deskjet, passbook, mfd 1038 network printer 1039 online ups 5 kva 1040 lcd / dlp projector 1041 power meter 1042 crimping tools 1043 computer toolkits 1044 computer spares: 1045 motherboards ( of different make ) 1046 cabinets 1047 processors ( of different make ) 1048 hard disk different types 500 gb or higher 1049 optical drives 1050 lcd / led / tft monitors 1051 pen drives 1052 external hard disk 1053 external dvd writer 1054 keyboards 1055 mouse 1056 anti static pads 1057 anti static wrist wraps 1058 smps 1059 blu ray drive and player 1060 digital camera 1061 hd display 1062 network storage 1063 card reader 1064 game video card 1065 web cam 1066 surround sound speakers 1067 different types of memory cards 1068 laptop kits 1069 laptop spares: cabinet with display, memory, hard disk, battery pack, keyboard membrane, chargers 1070 smps trainer kit 1071 ups trainer kit 1072 power electronics trainer kit 1073 post error debugging card 1074 smps tester 1075 pci slot testing tool 1076 windows server operating system 1077 windows operating system 1078 network management software 1079 ms office 1080 data recovery software 1081 linux server operating system ( samba / su se ) 1082 open source pc utility / tweak software 1083 computer chairs 1084 modem 1085 telephone line 1086 broadband internet connection 1087 fire fighting equipments 1088 hardware and network trainer kit 1089 wireless network adapter 1090 wireless access point 1091 router 1092 managed layer 2 ethernet switch 8 / 16 / 24 port 1093 network training system 1094 lan protocol simulation and analyser software 1095 network and internet security trainer 1096 lan cable tester 1097 network cables – utp 1098 network cables – coaxial, flat, ribbon 1099 lan cards, wi fi lan card 1100 connectors for cables 1101 media convertor 1102 utp jack panel 8 / 16 / 24 port 1103 sc couplers 1104 sc pigtails 1105 rj 45 connector 1106 fluke meter 1107 switch with poe ports 1108 poe adapters 1109 network camera ( outdoor / indoor ) 1110 fibre optics cable with lc connector 1111 lc connector module 1112 calliper inside with spring 15 cm 1113 center punch.10 mm. dia. x 100 mm 1114 dividers with spring 15 cm 1115 electrician screw driver 250 mm 1116 hammer ball peen with handle 0.5 kg 1117 hands file for second cut flat 20 cm. 1118 philips screw driver set of 5 pieces 100 mm to 300 mm 1119 screw driver blade 20 cm. x 9 mm. 1120 screw driver blade 30 cm. x 9 mm. 1121 spanner d.e. set of 12 pieces 6mm to 32mm 1122 spanner, ring set of 12 6 to 32 mm. ( metric ) 1123 steel rule 30 cm inch and metric 1124 steel tool box with lock and key ( folding type ) 400x200x150 mm 1125 wire cutter and stripper 1126 ac alternator slip ring puller variable 1127 air blow gun with standard accessories trigger operated with interchangeable nozzles 1128 ammeter dc with external shunt 300a / 60a 1129 air ratchet with standard accessories 1130 auto electrical test bench for checking dynamo, alternator & starter. with minimum2hp ac motor, digital voltmeter & ammeter. 1131 battery –charger capable to charge batteries from 5ah – 150ah. 1132 blow lamp 1 litre 1133 belt tensioner gauge 1134 car jet washer with standard accessories minimum3 phase 1hp 1400rpm motor, 3 reciprocating plungers with pressure regulator & gauge. 8m water hose with pressure adjustable brass nozzle. 1135 chain pulley block capacity with tripod stand 3 ton 1136 chisel flat 10 cm 1137 circlip pliers expanding and contracting 15cm and 20cm 1138 compression testing gauge suitable for diesel engine with standard accessories 1139 cylinder bore gauge capacity 20 to 160 mm 1140 cylinder liner dry & wet liner, press fit &slidefit liner 1141 depth micrometer 0 25mm 1142 dial gauge type 1 gr. a ( complete with clamping devices and with magnetic stand ) 1143 different type of engine bearing model 10 different types on board 1144 different type of piston model 5 different typeson board 1145 drift punch copper 15 cm 1146 drill twist ( various sizes ) 1.5 mm to 8 mm by 0.5mm 1147 electric soldering iron 230 v 60 watts 230 v 25 watts 1148 electric testing screw driver 1149 engineer’s square blade size 15 cm 1150 engineers stethoscope 1151 feeler gauge 20 blades ( metric ) 1152 file flat , bastard 20 cm 1153 file, half round , second cut 20 cm 1154 file, square second cut 20 cm 1155 file, square round 30 cm 1156 file, triangular , second cut 15 cm 1157 files assorted sizes and types including safe edge file ( 20 no’s ) 1158 flat file , second cut 25 cm 1159 flat file , bastard 35 cm 1160 fuel feed pump for diesel hand operated plunger type 1161 fuel injection pump ( diesel ) inline 4 / 6 cylinders rsv mechanical pneumatic governor type. 1162 fuel injection pump ve pump / distributor fuel rotary pump ( dpc ) pumps / along with special tools and accessories 1163 grease gun heavy duty trolley type 10 kg capacity 1164 growler 1165 hacksaw frame adjustable 20 30 cm 1166 hammer ball peen 0.75 kg 1167 hammer chipping 0.25 kg 1168 hammer mallet 1169 hammer plastic 1170 hand operated crimping tool / wire n ( i ) up to 4mm n ( ii ) up to 10mm 1171 hollow punch set of seven pieces 6mm to 15mm 1172 injector – multi hole type, pintle type 1173 injector testing set ( hand tester ) 1174 insulated screw driver 20 cm x 9mm blade 1175 insulated screw driver 30 cm x 9mm blade 1176 lifting jack screw 3 ton, 5ton & 20 ton 1177 multimeter digital lcd display 1178 oil can 0.5 / 0.25 liter capacity 1179 automotive oil pump for dismantling and assembling. 1180 outside micrometer 0 to 25 mm 1181 outside micrometer 25 to 50 mm 1182 outside micrometer 50 to 75 mm 1183 outside micrometer 75 to 100 mm 1184 philips screw driver set of 5 pieces ( pozidrivand torx drive ) 100 mm to 300 mm 1185 piston ring compressor 1186 piston ring expander and remover. 1187 piston ring groove cleaner. 1188 pliers flat nose 15 cm 1189 pliers round nose 15 cm 1190 pliers side cutting 15 cm 1191 portable electric drill machine upto 10mm ( heavy duty ) 1192 prick punch 15 cm 1193 punch letter 4mm ( number ) 1194 radiator cut section cross flow radiator with sectioned side tanks, radiator core. 1195 radiator cut section down flow radiator with sectioned upper & lower tanks, radiator core and cap. 1196 radiator pressure cap lmv 1197 scraper triangular 25 cm 1198 scriber with scribing black universal 1199 set of stock and dies metric 1200 sheet metal gauge 1201 spanner, adjustable 15cm 1202 spark plug spanner 14mm x 18mm x size long bit for alto / 800 1203 starter motor axial type, pre engagement type & co axial type 1204 steel measuring tape in a case 10 meter 1205 steel rule 15 cm inch and metric 1206 straight edge gauge 2 ft. 1207 stud extractor set of 3 1208 stud remover with socket handle 1209 surface gauge with dial test indicator plunger type 0.01 mm 1210 tachometer ( counting type ) 1211 tandem master cylinder with booster 1212 thermostat 1213 thread pitch gauge metric 1214 timing lighter 1215 torque wrenches 5 35 nm, 12 68 nm & 50 225 nm 1216 turbocharger cut sectional view latest wgt type to show turbine, impeller and compressor wheels. 1217 tyre pressure gauge with holding nipple 1218 universal puller for removing pulleys, bearings 1219 v’ block 75 x 38 mm pair with clamps 1220 valve lifter 1221 valve spring compressor universal 1222 vernier calliper 0 300 mm with least count 0.02mm 1223 vice grip pliers 1224 automotive water pump for dismantling and assembling 1225 wire gauge ( metric ) 1226 work bench 250 x 120 x 60 cm with 4 vices 12cm jaw 1227 working model of air brake assembly two brake drums, vehicular air compressor driven by suitable electric motor, air dryer, brake chamber . stop light, different valves, air pressure gauges. with all accessories. 1228 alternator assembly used for lmv alternator ( >50 amp ) 1229 carburetor – solex, mikuny for dismantling and assembling solex, mikuny for dismantling and assembling 1230 chain pulley block 3 ton capacity with tripod stand 3 ton capacity with tripod stand 1231 cut section model of mock layout of a motor car –electrical system working model wiring with parts and accessories of a car to be arranged according to the electrical circuit of a car. working of self starter, alternator, wiper motor, horn, lighting system, sparks from plug to be shown with distributor & battery. should be mounted on suitable table 1232 cut section models of shock absorbers 1233 cut section of cross ply and radial tyres 1234 cut section working model of automatic transmission gear box sectioned to show the internal mechanism of forward and reverse speeds. 1235 cut section working model of centrifugal clutch assembly. centrifugal clutch sectioned to show the internal details 1236 cut section working model of diaphragm clutch assembly. diaphragm clutch sectioned to show the internal details 1237 cut section working model of single plate clutch assembly single plate clutch sectioned to show the internal details 1238 demonstration board of electronic ignition system, ignition coil with ht coil, ht wires, spark plugs, ignition switch, coil, distributor, battery, and wiring. 1239 demonstration board of mpfi system with injectors, rail, inlet manifold, throttle body, distributor, ecu, purge valve, sensor, crank pulley, fuel tank module. 1240 disk brake in working condition with caliper assembly with all parts exhibiting brake disc, caliper assembly, tandem master cylinder, brake hoses, oil bottle, pedal, etc. 1241 drum brake assembly in working condition brake drum, tandem master cylinder, oil container, brake hose, brake pedal. 1242 front axle ( rzeeppa joint ) with stand for dismantling and assembly rzeppa joint of lmv. 1243 full floating axle and semi floating axle assembly drum & axle casing should be with all components in working condition. 1244 functional / experiment model of different type of sensors. with different type of sensors like throttle position sensor, manifold absolute pressure sensor, engine coolant temperature sensor, vehicle speed sensor, oxygen sensor, crankshaft position sensor, camshaft position sensor, intake air temperature sensor, mass air flow sensor, knock sensor with ecu. 1245 steering assembly – 1.rack & pinion 2.worm & roller 3. recirculating ball 4.power steering 5. electric assisted power steering n1. rack & pinion with steering wheel, column, tie rod end. n2. worm & roller steering assembly with drop arm. n3. recirculating ballsteering with pitman shaft and drop arm. n4. hydraulic working power steering with steering wheel, column, flow pipe, hydraulic pump, oil reservoir. n5. electric assisted power steering with rack and pinion, electric motor and motor control module 1246 synchronous gear box with stand for dismantling and assembly gearbox with 5 forward & 1 reverse gear 1247 tandem master cylinder with booster working model 1248 tubed tyre of car, trucks & motorcycle 1249 tubeless tyre of cars & trucks 1250 tyre & split rim wheel assembly 1251 working model of power windows showing parts like door, glass with motor and its gear arrangement and operating switch. 1252 working model of torque converter model of lmv 1253 air conditioned crdi vehicle in running condition lmv new vehicle with crdi engine, 04 strokes, 04 cylinders, bs iv, fitted with air condition. 1254 automotive exhaust 5 gas analyser ( petrol & diesel ) and diesel smoke meter ( optional ) exhaust 5 gas analyzer petrol arai approved to check co, co2, o2, and hc& no. 1255 diesel engine – crdi 4 strokefor dismantling and assembling with swiveling stand. latest 4 stroke 4 cylinder turbo charged crdi engine, 800 1600cc, in running condition, with ecm, bcm, and all sensors, wiring, fuel feed & cooling system & instrument cluster. 1256 diesel engine ( running condition ) stationary type single cylinder single cylinder, oh valves, fuel tank with handle, fuel feed, water cooling, oil pump. 1257 hydraulic jack hi lift type 3 ton capacity, and 5 ton capacity 1258 multi scan tool to scan engine, abs & ebd, at, srs, body control and immobilizer should perform automotive sensor simulation test specially designed to diagnose and simulate vehicle sensor faults for sensors like map sensor, intake air temperature sensor, tp sensor etc. 1259 spring tension tester manually operated with analogue display. 1260 trolley type portable air compressor belt driven compressor along with accessories 1261 working condition of diesel engine – crdi 4 stroke engine, assembly with fault simulation board latest 4 stroke 4 cylinder turbo charged crdi engine, with ecm, bcm and sensors, wiring, fuel feed, cooling system& instrument cluster. fault setting bank for minimum 8 sensors and with diagnostic socket&scanner to read the faults. engine management circuit diagram to be printed on the panel board. 1262 cut section of 4 / 6 cylinder diesel engine in moving condition to show movement of internal parts 6 cylinder diesel engine in working condition to show movement of internal parts 1263 diesel engine six cylinder in running condition latest diesel engine crdi 4 stroke 6 cylinders, turbocharged engine in running condition. all sensors, wiring, fuel feed, cooling system & instrument cluster 1264 air bag simulator driver & co driver air bags, seat belts with front seats, crash sensors, air bag ecu, wiring harness 1265 air conditioning service unit ( car ) suitable for r134a. recovery with vacuum pump, automatic drain & stop after recovery. 1266 four stroke petrol engine with cng setup working condition latest 4 stroke 3 / 4 cylinder mpfi engine in running condition 800 1600cc with ecm, bcm and all sensors, wiring, fuel feed system, cooling system& instrument cluster with cng / petrol selection switch on panel. 1267 heavy commercial vehicle fitted with latest 06 cylinder crdi diesel engine with all parts and accessories. ( without body on frame ) 1268 mpfi petrol engine with swiveling stand along with special tools for dismantling and assembling latest 4 stroke 3 / 4 cylinder mpfi engine in running condition 800 1600cc with ecm, bcm and all sensors, wiring, fuel feed system, cooling system & instrument cluster. 1269 petrol engine ( 2 stroke ) motor cycle / scooter along with special tools and accessories ( optional ) * if not available in market video demonstration may be used to explain working. cut section of 2 stroke 2 w engine single cylinder 1270 transfer case with stand for dismantling and assembly. to show the gear mechanism of forward and reverse speeds. 1271 tube / tyre vulcanizing machine 220 v , heater capacity 400w x 2 with different types of die &mould 1272 two post car lift – capacity 4000 kg hydraulic type with mechanical arms locking. 1273 tyre changer machine motorized pneumatic type, rim clamping facility, and bead breaking facility with air inflating device. 1274 ultrasonic injection cleaning equipment flow analysis & spray pattern test, leak test, auto programming mode, ultrasonic test with timer, min 500 ml lit ss tank with lid, ss stand. 1275 wheel alignment machine –computerized 3d ( optional ) latest machine for four wheel alignment. with connected camera , ir lighting source min. 8mm, reflector metal based, should work in sunlight 1276 wheel balancing machine for wheel balancing of lmv. motor 0.5 hp shaft diameter min 38mm. hardened flange assy. balancing catch nut of metal. 1277 working condition of petrol mpfi engine assembly with fault simulation board latest 4 stroke 3 / 4 cylinder mpfi in running condition, 800 1600cc with ecm, bcm and all sensors, wiring, fuel feed system, cooling system & instrument cluster with fault setting bank for minimum 6 sensors with diagnostic socket&scanner to read the faults. engine management circuit diagram to be printed on the panel board. 1278 battery 1279 brake fluids 1280 chalk, prussian blue 1281 chemical compound for fasteners 1282 diesel 1283 different type gasket material 1284 different type of oil seal 1285 drill twist ( assorted ) 1286 engine oil & engine coolant 1287 gear oils 1288 hacksaw blade ( consumable ) 1289 holders, lamp teakwood boards, plug sockets, 1290 petrol 1291 power steering oil 1292 radiator coolants 1293 safety glasses 1294 steel wire brush 50mmx150mm 1295 white board size 1200mm x 900 mm 1296 instructors lap top with latest configuration pre loaded with operating system and ms office package. 1297 lcd projector with screen. 1298 trainees locker 6½ ‘ x 3’ x 1½’ 1299 drawing board ( 700mm x500 mm ) is: 1444 1300 set square celluloid 45° ( 250 x 1.5 mm ) 1301 stool for trainees 1302 cupboard ( big ) 1303 white board 8ft. x 4ft. 1304 draughtsman drawing instrument box 1305 draughtsman table 1306 rule steel 24 1307 drawing board imperial size 1308 rule wooden ( consumable ) 24 1309 brush round short hair ( consumable ) 0 to 12 no. 1310 brush flat short hair ( consumable ) 0 to 12 no. 1311 varnish brush soft hair ( consumable ) 25mm, 50mm, 75mm, 100mm 1312 colour pallet for water colour ( consumable ) big size 1313 stencil / paper cutter ( consumable ) medium size 1314 t square imperial size 1315 easel a type stand 1316 square blade 150 mm 1317 scriber 1318 marking gauge 1319 wing compass 254 mm or 300 mm 1320 hand saw 450 mm 1321 tendon saw 300 mm 1322 hack saw with frame 1323 smoothing plane 1324 jack plane 1325 mallet round 1326 carpenter hammer ( ball pin ) 1327 hammer ( crass pin ) 1328 hammer ( claw ) 1329 portable electric hand drill machine 1330 drill bits ( consumable ) 3 mm, 5mm, 8mm, 10mm, 12mm 1331 chisel knife 5mm, 8mm, 10mm, 20mm, 30mm 1332 hacking knife 1333 palate knife set 1334 diamond glazier knife 1335 paint tin opener 1336 scraper knife 1337 shave huck knife 1338 glider knife 1339 pliers insulated 1340 paint burner ( acetylene gas ) 1341 blow lamp 1342 screw driver 100mm / 200mm 1343 step ladder ( aluminum ) 6 feet 1344 scaffolding ( movable ) h 2000mm x w 1400mm x l 2000mm. 1345 working bench 240 cm x 120 cm x 75 cm 1346 bench vice 50 mm jaw 1347 weight per litter cup 100 ml capacity 1348 ford cop for viscosity measurement with stand no.3 & no.4 1349 mild steel panels 300 mm x 200 mm ( 18 x 22 swg ) 1350 sink ( stainless steel ) h 250mm x w 450mm x l 600mm. 1351 fire buckets with stand ( 4 in 1 ) 1352 suction feed spray gun with accessories. 1 ltr. capacity of cup 1353 portable electric hand grinder 1354 glosso meter 1355 digital dft meter 1356 orbital sander machine with dust collector 1357 aerograph ( air brush / pen gun ) 1358 pneumatic polishing machine with pads 1359 goggles ( consumable ) 1360 face mask & respirator ( consumable ) 1361 gloves ( rubber ) ( consumable ) 1362 pipe vice 1363 hacksaw 1364 pipe wranch 10& 16 1365 flat file smooth finish 12 1366 circuler cut file 12 1367 raft cut 12 1368 pipe dai set metric & inches find peach 1369 gun spray with gravity feed cup with complete accessories with complete accessories ( capacity ¼ ltr. , 1 / 2 ltr. , 1 / 3ltr. , 1 ltr. ) 1370 conventional spray gun for pressure feed with complete accessories 1371 electric spray gun with complete accessories 1372 comb gauge 1373 pencil hardness tester 1374 digital weight machine capacity 5 kg. weighing scale 1375 air compressor 3 phase, 2 hp 1376 air compressor single phase, 1 hp 1377 pressure feed container with conventional 20 ltr. capacity with complete accessories 1378 electrostatic spray gun unit with complete accessories 1379 airless spray gun unit with complete accessories 1380 sealer drum press pump with sealer gun assembly with complete accessories 1381 side draught dry paint booth overall dimensions ( mm ) : 1580 ( w ) x 2250 ( d ) x 3200 ( h ) ; working dimensions ( mm ) : 1500 ( w ) x 1320 ( d ) x 2040 ( h ) 1382 power coating set up with gun booth & oven 1383 desk with locker 1384 metal shelving rack open type 1800 x 900 x 500 mm with 4 adjustable shelves 1385 green glass board 6x4 1386 cupboard 1387 computers with accessories ( table& chair ) 1388 scanner high resolution 1389 printer lager / colour 1390 software card draw / page make / photo shop / shree lippi / ism / acee dcee viewer ( latest version ) 1391 ups 3 kv 1392 camera digital 12 pix ( nikon ) with try pod 1393 radium plotter and cutter with stand complete accessories 48 1394 rule steel 300 mm both in inch and mm 1395 rule wooden 4 fold 600 mm 1396 scriber 200 mm 1397 chisel cold, flat 20 mm 1398 hammer ball pein 800 grams 1399 hammer ball pein 50 grams 1400 file flat rough 300 mm 1401 level spirit wooden 300 mm 1402 plumb bob 50 grams 1403 trowel c 125 i s: 6013 1404 stillson wrench 200 & 350 mm 1405 screw driver 250 mm 1406 wooden mallet small i s: 2022 1407 cutting pliers 200mm i s : 3650 1408 steel tape 5 m 1409 marking table 900x600x900mm high 1410 v blocks with clamps 80 / 7 63a is 2949 1411 combination set 200 mm 1412 scribing block, universal, 300 mm 1413 file half round, rough 300 mm 1414 file, square, rough 250 mm 1415 file, square, smooth 200 mm 1416 file triangular rough 250 mm 1417 file flat rasp 250 mm 1418 chisel cold flat 20 mmx300mm 1419 chisel cross cut 6x150 mm i s 402 1420 chisel round nose 3x150 mm i s 402 1421 chisel diamond point 6x150mm 1422 tap and die set to cut b.s.f. , b.s.w. and metric threads sizes no.6 to m 12 1423 screw pitch gauge to cover above threads 1424 punch , letter set 1425 punch , number set 1426 saw plumber 300mm 1427 spanner monkey up to 50mm 1428 stove melting solder 1429 cutter , pipe, wheel type 6mm to 25mm 1430 soldering iron , copper , bit , fire heated , hatched , straight , 500 grams 1431 snip straight 250mm 1432 snip bend 250mm 1433 try square 200mm 1434 caliper outside 150mm 1435 odd leg calliper 200mm 1436 mortise chisel 1437 mallet medium is: 2922 1438 gas welding set with oxygen acetylene cylinder 1439 goggles pair welder 100 mm 1440 brush steel wire 150x 50 mm 1441 table welding 1200x 750 mm with fire bricks top and stand 1442 pliers combination, 200 mm 1443 blow lamp 500 mililitre 1444 washer cutter 1445 mirror 100x150 mm 1446 scribing gauge 1447 soil pot with brush 1448 pot hook 1449 d. e. spanners 7x8, 10x11, 13x17, 19x22, 24x27 is:2028 1450 branch gimlets 1451 bending spring 1452 plumbers laddle 1453 tool caulking set of s 1454 plumbers metal melting pot 10 kg 1455 pipe stock and dies complete with stocks, bushing , bushing holders, taps and wrenches sizes covered, to suit pipes bore dia 6, 8, 10, 20, 25, 32, 40, &50mm 1456 pipe vice to grip up to 77 mm is 2587 1457 stillson pattern pipe wrenches 450 mm to take pipe up to 52 mm dia is 4003 1458 stillson pattern pipe wrenches 300mm to take pipe 20 mm to 32mm 1459 chain :pipe wrench 90mm 650 is 4123 1460 adjustable, spanner, a 375, is 6149 1461 anvil 50 or 63 kg. is 510 1462 pipe bender, manually operated 1463 leg vice, 75mm jaw on stand is 2588 1464 hand drill 6mm capacity with drill chuck ( electric ) 1465 drill twist ( straight shank ) 3mm to 6mm 1466 portable forge , 450mmwith hand blower 1467 flat smithy tong 1468 working bench 2400x1200x750mm with 4 voice 125 mm jaws 1469 bath tub small size 1470 wash basin equivalent metric ( 16x14x10 ) 1471 water heater 10 litres 1472 water closet ( european type p ) complete with over head cistern 1473 water closet ( indian type ) complete with over head cistern n 1474 urinal wall type complete with automatic system 1475 water meter 1476 steel lockers with 8 drawers metal rack ( 1800x1500x450mm ) 1477 metal rack ( 1800x1500x450mm ) 1478 black board with glass 1479 hammering drilling machine 1480 electric ppr pipe welding machine 1481 electric pump, 1 hp 1482 d.e. pedestal grinder with two wheels 175mm rough and smooth 1483 hydraulic pressure machine for testing leakage in gi pipe fittings etc. 1484 sight rail and bonning rod 1485 rachet pipe die 15 mm to 32 mm 1486 bench drilling machine with chuck and key upto 15mm capacity 1487 double face hammers 1488 dormat, pickaxe, spade, girmale 1489 pipe bender ( hydraulic type ) 1490 solar water heater system 1491 ring guage 15 mm, 20mm, 25mm, 32mm 1492 m.s flat 1493 m.s rod 1494 gi pipe b grade ½ø, ¾ø, 1ø 1495 gi pipe fittings socket, tee, bend, union, hex nipple ½ø, ¾ø, 1ø 1496 wooden plank 50 mm x 25 mm x 1 m 100 mm x 25mm x 1 m 1497 ms gas welding filler rod 1498 wire cut clay bricks 1499 river sand afs no.100 ~ 40 1500 stone aggregate 1501 cement portland 1502 copper tubes 6 mm ø, 25 mm ø 1503 copper brazing filler rod 1504 pvc pipes heavy duty ( suitable to use dies and tap ) ½ø, ¾ø, 1ø, 1½ø, 2ø , 4ø, 6 ø 1505 pvc pipe light duty ½ø, ¾ø, 1ø, 1½ø, 2ø 1506 pvc fittings reducer fta reducer, plain coupling, tee, bend, elbow, mta, fta , socket ½ø, ¾ø, 1ø, 1½ø, 2ø , 4ø, 6 ø 1507 c.pvc pipe 20 mm ø 1508 ppr pipe 20mm ø 1509 ac sanitary pipe coupling 100 mm ø 1510 ac pressure pipe coupling 100 mm ø 1511 ci water supply pile bell and spigot end 1512 ci water supply pipe flanged end 1513 wheel valve 1514 globe valve 1515 pvc ball valve 1516 water tap / pvc, s.s, brass size ½, ¾, 1 1517 non return valve, air valve 1518 m.s flange 1519 c.i.d joint 100mm 1520 lubricating oil 1521 lead 1522 spum yarn 1523 oxygen gas 1524 acetylene gas 1525 pvc bend 100 mm 1526 pvc y branch 100 mm 1527 pvc dod bend 100 mm 1528 pvc pipe sloe 1529 c.p piller tap 15 mm 1530 c.p waste coupling 35 mm 1531 pvc waste pipe 32 mm 1532 rock bolt 1533 pvc connection flexible tube 1534 hot and cold water mixer tap 1535 ppr pipe fittings ppr tee 20 mm, ppr elbow 20 mm 1536 pvc floor trap 1537 pvc gully trap 1538 pvc multi trap 1539 pvc multi floor trap 1540 white cement 1541 p o p ( plaster of paris ) 1542 gaskets etc 1543 push lock 1544 welding helmet fiber 1545 welding hand shield fiber 1546 chipping hammer with metal handle 250 grams 1547 chisel cold flat 19 mm x 150 mm 1548 centre punch 9 mm x 127 mm 1549 dividers 200 mm 1550 stainless steel rule 300mm 1551 scriber 150 mm double point 1552 flat tongs 350mm long 1553 hack saw frame fixed 300 mm 1554 file half round bastard 300 mm 1555 file flat 350 mm bastard 1556 hammer ball pane 1 kg with handle 1557 try square 6” 1558 spindle key 1559 screw driver 300mm blade and 250 mm blade 1560 number punch 6 mm 1561 letter punch 6 mm 1562 magnifying glass 100 mm dia. 1563 universal weld measuring gauge 1564 earth clamp 600a 1565 spanner d.e. 6 mm to 32mm 1566 c clamps 10 cm and 15 cm 1567 hammer sledge double faced 4 kg 1568 s.s tape 5 meters flexible in case 1569 electrode holder 600 amps 1570 h.p. welding torch with 5 nozzles 1571 oxygen gas pressure regulator double stage 1572 acetylene gas pressure regulator double stage 1573 co2 gas pressure regulator with flow meter 1574 argon gas pressure regulator with flow meter 1575 metal rack 182 cm x 152 cm x 45 cm 1576 first aid box 1577 steel lockers with 8 pigeon holes 1578 steel almirah / cupboard 1579 black board and easel with stand 1580 flash back arrester ( torch mounted ) 1581 flash back arrester ( cylinder mounted ) 1582 welding transformer with all accessories ( 400a, ocv 60–100 v, 60% duty cycle ) 1583 welding transformer ( or ) inverter based welding machine with all accessories ( 300a, ocv 60 – 100 v, 60% duty cycle ) 1584 d.c arc welding rectifiers set with all accessories ( 400 a. ocv 60 – 100 v, 60% duty cycle ) 1585 gmaw welding machine 400a capacity with air cooled torch, regulator, gas preheater, gas hose and standard accessories 1586 ac / dc gtaw welding machine with water cooled torch 300 a, argon regulator, gas hose, water circulating system and standard accessories. 1587 air plasma cutting equipment with all accessories, capacity to cut 12 mm clear cut 1588 air compressor suitable for above air plasma cutting system. 1589 auto darkening welding helmet 1590 spot welding machine 15 kva with all accessories 1591 portable gas cutting machine capable of cutting straight & circular with all accessories 1592 pedestal grinder fitted with coarse and medium grain size grinding wheels 300 mm dia. 1593 bench grinder fitted with fine grain size silicon carbide green grinding wheel 150 mm dia. 1594 ag 4 grinder 1595 suitable gas welding table with fire bricks 1596 suitable arc welding table with positioner 1597 trolley for cylinder ( h.p. unit ) 1598 hand shearing machine capacity cut 6 mm sheets and flats 1599 power saw machine 14’’ 1600 portable drilling machine ( cap. 6 mm ) 1601 oven, electrode drying 0 to 350°c, 10 kg capacity 1602 work bench 340x120x75 cm with 4 bench vices of 150 mm jaw opening 1603 oxy acetylene gas cutting blow pipe 1604 oxygen, acetylene cylinders ** 1605 co2 cylinder ** 1606 argon gas cylinder ** 1607 anvil 12 sq. inches working area with stand 1608 swage block 1609 die penetrant testing kit 1610 magnetic particle testing kit # 1611 fire extinguishers ( foam type and co2 type ) 1612 portable abrasive cut off machine 1613 suitable gas cutting table 1614 welding simulators for smaw / gtaw / gmaw 1615 leather hand gloves 14” 1616 cotton hand gloves 8” 1617 leather apron leather 1618 s.s wire brush 5 rows and 3 rows 1619 leather hand sleeves 16” 1620 safety boots for welders 1621 leg guards leather 1622 rubber hose clips ½ 1623 rubber hose oxygen 8 mm dia x 10 mtr. long as per bis 1624 rubber hose acetylene 8 mm dia x 10 mtr. long as per bis 1625 arc welding cables multi cored copper 400 / 600 amp as per bis 1626 arc welding single coloured glasses 108 mm x 82 mm x 3 mm. din 11a &12 a 1627 arc welding plain glass 108 mm x 82 mm x 3 mm. 1628 gas welding goggles with colour glass 3 or 4a 1629 safety goggles plain 1630 ag 4 grinding wheels 1631 instructor’s table and chair ( steel ) 1632 students chairs with writing pads 1633 instructors lap top with latest ( vista & above ) configuration pre loaded with operating system and ms office package. 1634 welding process, inspection & codes dvd / cds 1635 models : solid & cut section 1636 table for trainees 1637 trainer’s table 1638 trainer’s chair 1639 caliper inside spring 15 cm 1640 calipers outside spring 15 cm 1641 dividers spring 15 cm 1642 pliers combination 20 cm 1643 screw driver 20cm.x 9mm. blade 1644 screw driver 30 cm. x 9 mm. blade 1645 spanner d.e. set of 12 metric sizes6mm to 32mm 1646 spanner, ring set of 12 metric sizes 6 to 32 mm. 1647 spanners socket with speed handle, t bar, ratchet and universal of 28 pieces with box up to 32 mm set 1648 adjustable spanner pipe wrench 350 mm 1649 air impact wrench with standard accessories 1650 allen key set of 12 pieces 2mm to 14mm 1651 anvil with stand 50 kgs 1652 chisels cross cut 200 mm x 6mm 1653 clamps c 100mm 1654 clamps c 150mm 1655 cleaning tray 45x30 cm. 1656 compression testing gauge suitable for petrol engine. with standard accessories 1657 cylinder bore gauge 20 to 160 mm capacity 1658 drill point angle gauge 1659 drill twist 1.5 mm to 15 mm ( various sizes ) by 0.5 mm 1660 engineer’s square blade 15 cm. 1661 file flat bastard 20 cm 1662 granite surface plate with stand and cover 1600 x 1000mm 1663 hammer copper 1 kg with handle 1664 hand reamers adjustable 10.5 to 11.25 mm, 11.25 to 12.75 mm, 12.75 to 14.25 mm and 14.25 to 15.75 mm 1665 hand shear universal 250mm 1666 hand vice 37 mm 1667 left cut snips 250mm 1668 marking out table 90x60x90 cm. 1669 oil stone 15 cm x 5 cm x 2.5 cm 1670 philips screw driver set of 5 pieces ( 100 mm to 300 mm ) 1671 pipe cutting tool 1672 pipe flaring tool 1673 power supply 0 12 v, lamp 1674 right cut snips 250mm 1675 rivet sets snap and dolly combined 3mm, 4mm, 6mm 1676 scooter / motor cycle repairing stand 1677 scraper flat 25 cm 1678 scraper half round 25 cm 1679 scriber 15 cm 1680 set of stock and dies unc, unf and metric 1681 shear tin man’s 450 mm x 600mm 1682 shear tinnman’s 300mm 1683 soldering copper hatchet type 500gms 1684 solid parallels in pairs ( different size ) in metric 1685 spanner clyburn 15 cm 1686 spanner t. flocks for screwing up and upscrewing inaccessible positions 1687 spanner, ring set of 12 metric sizes 6 to 32 mm. 1688 spanners socket with speed handle, t bar, ratchet and universal up to 32 mm set of 28 pieces with box 1689 spark lighter 1690 spark plug spanner 1691 steel measuring tape 10 meter in a case 1692 surface gauge with dial test indicator plunger type i.e. 0.01 mm 1693 taps and dies complete sets bsf 1694 taps and wrenches metric 1695 telescope gauge 1696 temperature gauge 0 100 deg c 1697 thread pitch gauge metric, bsw 1698 torque wrenches 1699 trammel 30 cm 1700 tyre pressure gauge with holding nipple 1701 v’ b lock with clamps 75 x 38 mm pair 1702 vacuum gauge 0 to 760 mm of hg 1703 vernier caliper 0 300 mm with least count 0.02mm 1704 vice grip pliers 1705 voltmeter 50v / dc 1706 work bench with 4 vices 12cm jaw 250 x 120 x 60 cm 1707 arbor press hand operated 2 ton capacity 1708 automotive exhaust 5 gas analyzer ( petrol &diesel ) or diesel smoke meter 1709 battery tester to test 12v / 24v 1710 bench lever shears 250mm blade x 3mm capacity 1711 cut section working model of continuous variable transmission 1712 cut section working model of rotary clutch assembly of two wheeler 1713 demonstration board of magneto ignition system of a two wheeler 1714 discrete component trainer / basic electronics trainer 1715 drilling machine bench to drill up to 12mm dia along with accessories 1716 dual magnetization yoke ac / hwdc, 230 vac, 50hz 1717 gas welding table 1220mm x760mm 1718 grinding machine ( general purpose ) d.e. pedestal with wheels rough and smooth 300 mm dia 1719 ignition coil and cdi unit of four different make 1720 layout of working model 12 v automobile electrical systems 1721 liquid penetrant inspection kit 1722 motor cycle ( four stroke engine ) with digital twin spark 1723 motor cycle ( two stroke engine ) 1724 motor vehicle ( 3 wheeler ) 1725 pipe bending machine ( hydraulic type ) 12mm to 30mm 1726 pneumatic rivet gun 1727 ridge cutter 1728 scooter ( four stroke engine ) 1729 shock absorber for two wheeler fourdifferent type 1730 spring tension tester 1731 three wheeler chassis frame & power transmission system. 1732 three wheeler engine for dismantling and assembling 1733 three wheeler gear box for dismantling and assembling 1734 three wheeler steering system for dismantling and assembling 1735 tin smiths bench folder 600 x 1.6mm 1736 trolley type portable air compressor single cylinder with 45 1737 capacity air tank, along with accessories & with working 1738 welding transformer 150 300 amps 1739 working model of electronic ignition system of three wheeler 1740 working model of electronic ignition system of two wheeler 1741 automatic transmission oils 1742 battery smf 1743 different type gasket material 1744 different type of oil seal 1745 emery paper 36–60 grit , 80–120 grit 1746 engine coolant 1747 engine oil 1748 gloves for welding ( leather and asbestos ) 1749 hacksaw blade ( consumable ) 1750 hand rubber gloves tested for 5000 v 1751 holders, lamp teakwood boards, plug sockets, solders, flux wires and cables batteries round consumable blocks and other consumables as required 1752 lapping abrasives 1753 petrol 1754 safety goggles 1755 book shelf ( glass panel ) 6½ ‘ x 3’ x 1½’ 1756 desktop computer and related ms office software 1757 discussion table 8’ x 4’ x 2½ ‘ 1758 fire extinguishers, first aid box 1759 instructional material – nimi books / ref.books 1760 internet connection with all accessories 1761 laser printer 1762 lcd projector / led / lcd tv 42” 1763 multimedia dvd for automotive application / subjects 1764 online ups 2kva 1765 storage rack 6½ ‘ x 3’ x 1½’ 1766 suitable class room furniture 1767 suitable work tables with vices 1768 tool cabinet 6½ ‘ x 3’ x 1½’ 1769 trainees locker ( 20 lockers ) 6½ ‘ x 3’ x 1½’ 1770 desktop computer cpu: 32 / 64 bit i3 / i5 / i7 or latest processor, speed: 3 ghz or higher. cache memory: minimum 3 mb or better. ram: 8 gb ddr iii or higher. hard disk drive: 500gb or higher, 7200 rpm ( minimum ) or higher, wi fi enabled. network card: integrated gigabit ethernet ( 10 / 100 / 1000 ) wi fi, usb mouse, usb keyboard and monitor ( min. 17 inch ) , standard ports and connectors. dvd writer, speakers and mic. licensed windows operating system / oem pack ( preloaded ) , antivirus / total security 1771 laptop 4th gen ci5 or higher processor, 4gb ram, 1tb hard disk, win8 / latest preloaded licensed os, 2gb graphics card, dvd writer, standard ports and connectors. 1772 wi–fi router with wireless connectivity 1773 switch 24 port 1774 structured cabling in lab to enable working with wired networks for practical 1775 internet connectivity broadband connection with min. 2 mbps speed 1776 registered domain at least 100 mb web space 1777 laser printer colour a4 size 1778 network laser printer monochrome a4 size 1779 optical scanner flatbed a4 1780 digital web cam high resolution ( 3.1 mp or higher ) 1781 dvd or blu ray writer 24x or higher external ( usb ) 1782 lcd projector 3000 lumens or higher 1783 projector screen matte ( antiglare ) screen 1784 online ups 3kva 1785 crimping tool rj 45 1786 network rack 4u for 24 port 1787 digital multimeters 3.5 digit handheld type. 1788 screw driver set standard 1789 mini dongle for bluetooth devices connection usb 1790 headphone &mic. set wired 1791 sound system 2:1 1792 external hard disk 1 tb 1793 patch panel 24 port 1794 lan tester utp cat5 cable tester ( rj 45 ) 1795 punching tool for punching rj 45 socket with cat 5 cable 1796 ms office 2010 ( professional ) or the latest version available at the time of procurement 1797 antivirus for – clients / workstations in profile validity of an year or more which should be renewed upon expiry 1798 open office or equivalent latest version 1799 gimp / irfanview image editor or equivalent latest version 1800 linux os latest version 1801 web authoring tool wysiwyg web authoring tool dreamweaver or open source tools like kompozer, front page or similar tools along with ftp tools for ex. filezilla etc. 1802 tally erp 9 or latest 1803 e commerce simulation software latest version 1804 web server http web server / xampp or any other similar server 1805 vacuum cleaner hand held 1806 pigeon hole cabinet 20 compartments 1807 chair and table for the instructor with armrest mounted on castor wheels, adjustable height / standard 1808 dual desk or chair and tables for trainees standard 1809 computer table laminated top 150x650x750 mm with sliding tray for key board and one shelf of storage 1810 operators chair without arms mounted on castor wheels, adjustable height 1811 printer table 650x500x750 mm can be varied as per local specifications 1812 air conditioner split type 1.5 tons 1813 storage cabinet 60x700x450mm 1814 white board minimum 4x6 feet 1815 white board marker assorted colour 1816 duster cloth 2’ / 2’ 1817 cleaning liquid 500 ml 1818 photo copy paper a4 1819 full scape paper white 1820 cartridges for printer colour / monochrome as per model of the printer 1821 i / o box with socket rj 45 1822 rj 45 connector for connecting utp cat 5 cable 1823 optical mouse usb / ps2 1824 key board usb / ps2 1825 smps 12v dc 1826 cmos batteries 3.0 v 1827 power chord 3 pin 1828 cable cat 5 / 5e 1829 stapler small 1830 stapler big 1831 battery for remote aaa 1832 battery for clock aa 1833 pen drive 8 gb 1834 cds 52x or higher 1835 dvds 4.7gb or higher 1836 wall clock analog 1837 battery for lan tester 9 v 1838 power adapter for hub, switch, router 1839 tail comb 1840 style comb 1841 open teeth tail comb 1842 small bowl 1843 facial band 1844 spray bottle 1845 nail file 1846 nail cutter 1847 plain switches 1848 switch stand 1849 personal towel medium 1850 napkin 1851 hair accessories 1852 make up brush 1853 pack & bleach brush 1854 wax applicator 1855 braid 1856 bob pins 1857 juda pins 1858 setting clips 1859 lab coat 1860 manicure set 1861 pedicure set 1862 barber scissors 1863 thinning scissors 1864 velcro rollers large, medium, & small 1865 perm rollers ( star perm, ladder perm, spiral rods, chop sticks, wooden rollers ) different sizes small, medium, large 1866 manual razor 1867 dust brush 1868 swiggle 1869 dye brush 1870 back view mirror 1871 cutting sheet 1872 dye bowl 1873 professional hair brushes set 1874 scalp steamer 1875 hot rollers 1876 dummy head on stand with slipon 1877 dryer 1878 crimper 1879 mirror panel 1880 styling chair ( multipurpose for hair & beauty services ) 1881 shampoo station with chair 1882 hair trolley 1883 ceramic straightening iron 1884 curling rods with attachments 1885 neck tray ( for perming ) 1886 rebonding boards 1887 benders 1888 hood dryer 1889 magnifying lamp 1890 vapozone 1891 beauty studio ( ultrasonic / galvanic / high frequency, brushing unit, vacuum & spray ) 1892 high frequency 1893 ems machine 1894 infra red lamp 1895 wax heater 1896 beauty trolleys 1897 facial bed 1898 manicure bowls 1899 pedi spa tub 1900 manicure stools 1901 manicure table 1902 pedi stool 1903 manicure trolley 1904 dry sterilizer ( ultra violet ) 1905 boiler 1906 front wash basin 1907 curtain / blinds for lab 1908 blanket 1909 hot towel cabinet 1910 computer system with internet facility & printer 1911 computer table 1912 heat convector 1913 student lockers 1914 refrigerator 1915 teachers chair and table set 1916 black head remover 1917 display board minimum 3 x 4 feet size 1918 wet sterilizer 1919 students chair with flap 1920 lcd projector 1921 white magnetic board with felt board 1922 yoga mat 1923 teachers chair 1924 teachers table 1925 measuring tape 150 cm 1926 seam ripper 1927 thimble 1928 tailors card scale triangular 1929 tailors square plastic 1930 french curve set of three 1931 thread cutter 24 1932 scissors 25 cm 1933 leg shaper plastic 1934 screw driver set 1935 pressing table 1936 rubber mat size as per requirement 1937 pattern punch 1938 pattern notcher 1939 pattern hanging stand 1940 water tub 60 cm dia 1941 electric automatic steam press 1942 sewing machine single needle lock stitch industrial model 1943 over lock machine 3 thread 1944 zigzagmulti purpose machine 1945 double needle machine 1946 button hole machine 1947 button sewing machine 1948 machine attachments 1949 drafting table 1950 display board covered with glass or acrylic sheet 120 x 90 cm 1951 pigeon hole almirah 10 lockers with separate locking arrangements for trainees 1952 dummy lady, men, kid different sizes 1953 printer colour laser 1954 work station with chair 1955 single desks for trainees with arrangements of keeping books etc. 1956 drawing table with adjustable top. desk having facility of keeping tools 1957 revolving chair with adjustable height & back support 1958 adjustable set square 1959 dress forms ( dummies ) n• children n• ladies n• gents 1960 tracing table 1961 mannenquins: childrens, ladies, gents 1962 leg shaper 1963 cart chop 1964 table sharpener 1965 rubber mat ( size as per requirement ) 1966 trial room with 3 side mirrors of size 150 cm x 60 cm each with arrangements of hanging dresses 1967 pick glass 1968 chairs with low back rest or stools for the machines ( one for each machine ) 1969 steel almirah 195 x 90 x 60 cm 1970 mannequins ( lady ) 1971 mannequins ( kids ) 1972 mannequins ( gents ) 1973 computer with multimedia system ( latest configuration ) with software & ups ( 0.5 va with 15 minute back up ) 1974 server system ( latest configuration ) with software 1975 lan connectivity & internet facility to the computers 1976 designing software coral draw latest version 1977 colored laser printer a3 1978 computer table for server 1979 table for scanner 1980 storage almirah ( size as per requirement ) 1981 air conditioner unit split type 2 ton capacity with stabilizer 1982 modular workstation with chair 1983 trainers table & chair 1984 computer table with revolving chair 1985 for dictation room tables, chairs and headphones / speakers or microphone systems ) 1986 computer latest version with latest os 1987 printer table 1988 glazed white board 8’ x 4’ 1989 pigeon hole lockers ( 12 locker ) with external lock 1990 book case 1991 photocopier machine ( network ready ) with scanner 1992 ups 650 va 1993 fax machine ( latest model ) 1994 tool kit ( hand tools ) 1995 air conditioners 2 ton with cvt 1996 broad band connection or wi fi 1997 led tv 36 inch 1998 application software ( ms office ) educational version 1999 antivirus latest version 2000 shorthand pencil 2001 shorthand notebook 2002 eraser 2003 sharpner 2004 scale 12 2005 cutter 2006 white paper a4, a3, a2 2007 correcting fluid white 2008 cloth duster 2009 pilot pen 2010 file folder 2011 marker 2012 white board duster 2013 printer cartidge 2014 carbon paper plastic 2015 envelope different size 2016 colien 2017 box file 2018 allpin / jam clip 2019 scissor for paper cutting 2020 dustbin 2021 fevistick 2022 dvd 2023 cd dwr 2024 register 2025 pocker small and big 2026 heighlighter 2027 sketch pen colour 2028 cello tape / brown tape 2029 outward corrospending register 2030 inward corrospending register 2031 post and expenditure entry register 2032 paper weight 2033 drawing pins 2034 stapler pins 2035 pinking shears 2036 garment hangers 2037 blanket for padding of pressing table 2038 rubber mat size as per requirement 2039 sprayer 2040 waste bin big / small 2041 stand for hanging dresses 2042 bar tack machine 2043 feed off the arm double needle 2044 instructor table 2045 instructor chair 2046 steel almirah 195x 90 x 60 cm 2047 locks for above pigeon hole 2048 calculator desk type 2049 white board with accessories size as per requirement 2050 revolving chairs without arms 2051 thread cutter 2052 color plate 2053 color brush no. 00, 1, 2. 2054 scale plastic 12” 2055 compass 2056 hangers wooden hangers 2057 embroidery ring size 1, 2, 3, 4, 5, 6, 7 2058 stencil different shapes and design, numerical and alphabets, 2059 water colour 2060 eraser, pencil, sharpner 2061 computerized embroidery machine ( multi needle ) with necessary 2062 attachments / accessories 2063 trade related software 2064 coral draw software 2065 computer system with ups, operating system, antivirus and internet latest configuration 2066 printer 2067 automatic sewing machine 2068 round table with step for embroidery machines 2069 automatic electric press 2070 carpet size as per requirement 2071 frames / hoops 2072 pinking scissors 2073 appliqué scissors 2074 cutting scissors 2075 trainees lockers ( 10 lockers ) 2076 wall clock 2077 faculty table & chair set 2078 computer set with ups & multimedia projector 2079 white magnetic board with felt board & accessories 2080 a / c unit split type 2 tr capacity with stabilizer 2081 computer ( pc ) with latest configurations and internet connection with standard operating system and standard word processor and worksheet software. 2082 ups 500va 2083 scanner cum printer 2084 computer tables 2085 computer chairs 2086 lcd projector 2087 white board 1200mm x 900mm 2088 cotton cloth plain ( pink, black, mehroon, green ) 2089 cotton cloth printed ( blue, pink, green, yellow ) 2090 casement ( cream colour, mehroon, black, navy blue ) 2091 matty cloth ( pink, firozi ) 2092 net cloth ( pink, white, navy blue ) 2093 sotten cloth ( pink, firozi, white, red ) 2094 pant and shirt cloth 2095 thread 2096 thread for kadhai 2097 bakram 2098 hook 2099 show button 2100 machine needle 14, 16, 18 2101 hand needle 2102 milton chalk 2103 sharpener 2104 french curve set 2105 measuring tape tailor 2106 seam ripper 2107 card scale 2108 colour pencil 2109 water colour 2110 plastic scale 12 2111 l square plastic 2112 leg shaper plastic 2113 plastic tub big 2114 balty 2115 plastic jug 2116 elastic 1 / 2 2117 elastic 1 2118 elastic 2 2119 cello tape 2 2120 file cover 2121 file ( cobra ) 2122 gum stick 2123 ball pen ( rotomac ) 2124 correction pen 2125 non duster rubber 2126 pencil 2h 2127 pencil 2b 2128 pencil hb 2129 sketch pen 2130 white paper 2131 drawing sheet 2132 basi paper 2133 tracing paper a4 size 2134 cutter log 2135 tracing pen 2136 cello tape 1 / 2 2137 cello tape 1 2138 punch plier big size 2139 duster cotton cloth 2140 paper cutter 2141 dust bin 2142 cotton bundle 2143 cold cream 2144 shampoo 2145 nail decorative tube 2146 hair decorative pin 2147 hair massage oil 2148 nutrillizer ( white orange ) 2149 cleanser ( line and normal ) 2150 foundation 2151 dry cake 2152 pain cake 2153 makeup fixer 2154 shimer powder 2155 shimer cake 2156 eye shadow ( cream, powder base ) 2157 high lighter ( golden, silver yellow ) 2158 eye brow pencil 2159 eye liner 2160 eye liner sealer 2161 blusher 2162 mascara 2163 lip pencil ( different colour ) 2164 lipstick ( different colour ) 2165 makeup remover 2166 artificial oilseas 2167 rubber band 2168 back comb removing brush 2169 hair pin 2170 bun ( hair ) 2171 finishing brush 2172 curling rolls 2173 hair band 2174 hair back pin 2175 jura pin 2176 bob pin 2177 massage cream 2178 lotus hurble sunscream 2179 face wash 2180 body lotion 2181 vaselene 2182 rose water 2183 body spray 2184 boro plus 2185 hand wash 2186 nail polish removal 2187 nail polish ( different colour ) 2188 cleansing milk 2189 skin toner 2190 astrigent lotion 2191 threading thread 2192 anti wrinkle cream ( lotus ) 2193 massage oil 2194 massage cream 2195 nail cutter 2196 massager 2197 hair net 2198 gloves 2199 dye brush 2200 apron 2201 brush 1 no 2202 powder puf 2203 latix spunge 2204 scissor ( plastic handle ) 2205 pumic stone 2206 hydeogen paraoxide 2207 hair cutting sheet 2208 nail artificial 2209 spray bottle 2210 makeup brush 2211 under eye dark circle cream 2212 tail comb 2213 style comb 2214 hand mirror 2215 wall mirror 2216 soft brush 2217 manicure bowl 2218 pedicure bowl 2219 switch stand 2220 plain switch 2221 livon silk and shine 2222 facial band 2223 mehndi powder and tube 2224 setting clip 2225 hot wax 2226 ammonia 2227 nail filer plastic handle 2228 face dummy 2229 bleach brush 2230 iron scaper 2231 facial kit 2232 hair colour 2233 telcom powder 2234 bleach cream 2235 m.s square rod 30 mm 2236 m.s square rod 25 mm 2237 hacksaw blade 2238 mobil oil 2239 grease 2240 cotton jute 2241 cotton cloth 2242 chalk white 2243 carbon a4 2244 carbon a3 2245 black board duster 2246 photocopy paper a4 size 2247 photocopy paper a3 size 2248 file handle 2249 emery paper 80 no 2250 correction pen 2251 drawing sheet 2252 tracing paper a3 size 2253 cutter log apsara 2254 tracing pen 2255 gum bottle 2256 punch machine big size. 2257 duster cotton 2258 pen pilot 2259 scatch pen blue 2260 stepler ( big ) 2261 stepler ( small ) 2262 stepler medium 2263 paper pin 2264 stepler pin big 2265 note pad 2266 f.s paper 2267 type paper 2268 rise paper 2269 rulled paper 2270 drying sheet 2271 gum bottle 700 ml 2272 gum bottle 100 ml 2273 stamp pad big 2274 stamp pad medium 2275 stamp pad small 2276 pad ink 2277 tag ( dhaga ) thick and big 2278 coloured chalk 2279 white non dust chalk 2280 coloured pencil for scatch 2281 dot pen ( use and throw ) 2282 marker permanent 2283 marker non permanent 2284 tumbler 2285 towel big 2286 towel small 2287 old dhoti 2288 pen mix clour 2289 sofa three seater 2290 phenyl 2291 nepthaleen ball 2292 phool jhadhu 2293 nariyal jhadhu 2294 toilet brush 2295 pocha big size 2296 whyper 2297 harpic 2298 acid toilet 2299 cfl 15 watt 2300 cfl 18 watt 2301 cfl 23 watt 2302 cfl 35 watt 2303 cfl 65 watt 2304 cfl 85 watt 2305 street light 85 watt with danda complete 2306 choke electronic 40 watt 2307 choke copper 40 watt 2308 tube light 40 watt 2309 led patt fanti complete 2310 led 2 watt 2311 led 5 watt 2312 led 7 watt 2313 led 12 watt 2314 led 15 watt 2315 starter 40 watt 2316 side holder 2317 tube light fanti blank 2318 tube light fanti complete 2319 tape 1 / 2 2320 bulb 100 watt 2321 bulb 200 watt 2322 bulb 15 watt 2323 bulb holder 2324 pendent holder 2325 casing caping 1 / 2 2326 casing caping 3 / 4 2327 casing caping 1 2328 pvc copper wire .75 mm 2329 pvc copper wire 1 mm 2330 pvc copper wire 1.5 mm 2331 pvc copper wire 2.5 mm 2332 pvc copper wire 4 mm 2333 pvc copper wire 6 mm 2334 pvc copper wire 10 mm 2335 pvc copper wire 3 / 20 2336 pvc copper wire 3 / 22 2337 pvc copper wire 7 / 20 2338 pvc copper wire 7 / 22 2339 mcb 16 amp 2340 mcb 32 amp 2341 mcb 64 amp 2342 gun tape dispensor 2343 executive table for principal 2344 executive chair for principal 2345 side rack for principal table 2346 visitor chair 2347 office bag 2348 water purifier ro 2349 cool cage for water 2350 electric kettle 2351 bone china cup & plate set of 6 pcs 2352 pin cusion 2353 coaster 2354 paper weight 2355 plate full size bone china 2356 plate quater size bone china 2357 pen stand 2358 taper table stand 2359 fan ac 1200 mm 2360 wall fan 2361 switch 5 amp 2362 socket 5 amp 2363 switch socket combined 15 amp 2364 switch 15 amp 2365 socket 15 amp 2366 fan regulator 2367 indicator 5 amp 2368 board 4x4 2369 board 7x4 2370 board 8x10 2371 board 10x12 2372 sunmica sheet 4x4 2373 sunmica sheet 7x4 2374 sunmica sheet 8x10 2375 sunmica sheet 10x12 2376 tray fiber 2377 aluiminium round mixed sizes 2378 aluiminium block mixed sizes 2379 acrelic sheet 150x100x100 mm 2380 ms flat mixed sizes 2381 ms angle mixed sizes 2382 ms rod mixed sizes 2383 ms squire rod mixed sizes 2384 ms pipe 50 mm dia thickness 3 mm 2385 ms sheet 2386 c.i. round 100 mm dia x 25 mm 2387 c.i. plate 100 mm dia x 20 mm 2388 c.i. block mixed sizes 2389 gi pipe 50 mm dia 2 mm thickness 2390 gi sheet 25 gauge 2391 gi sheet 20 gauge 2392 glass coloured 108x82 mm for welding screen 2393 glass white 108x82 mm for welding screen 2394 grinding wheel 6x3 / 4x1 ¼ bore size with plastic bush 13x31.5 cm 2395 high speed steel 2396 cobalt bit ¾ x 6 2397 cobalt bit 5 / 8 x 6 2398 cobalt bit ½ x 6 2399 cobalt bit 3 / 8 x 6 2400 hexa blade 12x1 / 2x1 / 32 superior quality per pkt 2401 emery paper zero number 2402 emery cloth 80 number 2403 cutting compound 2404 transformer oil 2405 electrod ( 10 no. ) 3.15 mm 2406 electrod ( 12 no. ) 2.5 mm 2407 electrod 4 mm 2408 tungston electrod 2409 c.i. electrod 2410 spot welding electrod 2411 filler rod alumenium 1.5 mm 2412 filler rod stainless steel 2 mm 2413 mig welding wire 0.8 mm 2414 mig welding wire 1.0 mm 2415 mig welding wire 1.2 mm 2416 mig wire welding contact tip 0.8 mm 2417 mig wire welding contact tip 1.0 mm 2418 mig wire welding contact tip 1.2 mm 2419 oxygen gas filling without cylender 2420 acetylene gas filling without cylender 2421 co2 gas filling without cylender 2422 argon gas filling without cylender 2423 carbide tip tringular ¾ 2424 carbide tip squire ¾ 2425 cotton waste 2426 old cotton dhoti 2427 grease castrol a.p. 3 2428 mobil oil s.a.e. 40 2429 power saw blade 14 single teeth superior quality 2430 wire brush nylon with wooden handle for cleaning workshop machines big size superior quality 2431 welding nozle cap for mig welding 2432 welding tip size 0.8 mm 2433 welding tip size 1.00 mm 2434 welding tip size 1.2 mm 2435 welding gel 2436 welding liner standard size 2437 welding spray 2438 welding adaptor 2439 m.s. squire net 1 swg 10 no. width 4 feet 2440 m.s. barfee jali swg 12 no. 2441 m.s square net twisted 2 width 4 feet 2442 two pin top 5 amp. f / t 2443 three pin top 5 amp f / t 2444 three pin top 15 amp f / t 2445 three pin socket 5 amp f / t 2446 three pin socket 15 amp f / t 2447 single way switch 5 amp f / t 2448 single way switch 15 amp f / t 2449 two way switch 5 amp f / t 2450 switch with socbet 15 amp f / t 2451 intermediate switch 5 amp f / t 2452 bell push switch 2453 pendent holder 2454 baton holder 2455 casing capping pipe 1 ( 5 feet length ) 2456 casing tea 1 2457 casing nails 2458 casing corner 1 2459 casing straight 1 2460 casing box 2way, 3way, 4way 1 2461 p.v.c rawel plug 1, 1.5, 2 2462 pvc pipe 1 2463 pvc saddle 1 2464 pvc band 1 2465 pvc elbow 1 2466 junction box 4 way1 2467 junction box 3 way1 2468 bare aluminum wire 16 swg 2469 bare aluminum wire 8 swg 2470 pvc copper wire 3 / 20 swg 2471 pvc copper wire 7 / 20 swg 2472 pvc copper wire 1 / 18 swg 2473 pvc copper wire flexibe 30 / 76 swg 2474 multi strend copper wire 1.5mm 2475 multi strend copper wire 2.5mm 2476 multi strend copper wire 4.00mm 2477 pvc alluminim wire 2.5mm 2478 nicrome wire 20 swg 2479 super enamiled copper wire mixed sizes 2480 wooden board 8x10x2 open cancealed 2481 wooden board 7x4x2 open cancealed 2482 wooden board 4x4x2 open cancealed 2483 sunmaica sheet 8x10 ( 3mm thickness ) 2484 sunmaica sheet 7x4 ( 3mm thickness ) 2485 sunmaica sheet 4x4 ( 3mm thickness ) 2486 wooden screw 1 ( heavy head ) 2487 wooden screw 1 1 / 2 ( heavy head ) 2488 wooden screw 1 / 2 ( heavy head ) 2489 steel screw 3 / 4 2490 steel screw 1 2491 steel screw 1 1 / 2 2492 bulb 60 watt 2493 bulb 100 watt 2494 bulb 200 watt 2495 bulb coloured 15 watt 2496 cfl tube 14 watt 2497 cfl tube 18 watt 2498 cfl tube 23 watt spirell type 2499 cfl tube 27 watt spirell type 2500 cfl tube 65 watt u taube type 2501 cfl tube 5 watt 2502 tube light 40 watt 2503 tube light choke 40 watt electronic 2504 tube light choke 40 watt copper 2505 tube light starte 2506 tube light base / patti 4feet 2507 kit kat fuse 16 amp f / t 2508 pvc insulation tape roll 1 2509 cotton tape 3 / 4 ( for binding ) 2510 pvc insulation papper 0.05mm 2511 pvc insulation papper 0.07mm 2512 latherised sheet 2513 sleeve 1mm 2514 sleeve 3mm 2515 sleeve 4mm 2516 sleeve 5mm 2517 crample sheet 0.5 mm 2518 crample sheet 0.7 mm 2519 electric bell 2520 indicator 5amp f / t 2521 solder wire 60:40 2522 room heater blower type thermostaticaly controled 1500 watt 2523 two core cable 6mm 2524 mercury vapour lamp 80 watt pin type 2525 mercury vapour lamp choke 80 watt 2526 mercury vapour lamp condensor for 80 watt 2527 mercury vapour lamp holder three pin type 2528 condensor 3.15 mfd 2529 condensor 4.00 mfd 2530 ceilling rose 2531 air dry varnish 2532 double pole main switch 15amp f / t 2533 main switch icdp 15amp 500v size 8x7 2534 main switch ictp 32amp 500v 2535 main switch ictp 60amp 500v 2536 riversing switch 32amp 3phase 2537 push button starter 3phase 32amp 2538 cut out 16amp 450v 2539 cut out 60 amp 2540 electric extension box with lead & 3 pin top 2541 mcb 6 amp 2542 mcb 32 amp 2543 mcb 16 amp 2544 mcb box for one mcb 2545 mcb box for two mcb 2546 mcb box for three mcb 2547 mcb box with mcb for 1.5 ton ac 2548 plug top for 1.5 ton ac box 2549 stabliger 90 300v for 1.5 ton ac sarbal or inmag 2550 fan regulator electronic step type 2551 copper lugs 2552 sodium vapour lamp complete set with handle, complete fitting for street light 180 watt 2553 mercury vapour lamp complete set with handle complete fitting 125 watt for street light 2554 microtech inverter 850 va ( sine wave ) 2555 inva tubler it 500 exide battery 2556 solar light system with pannel & battery & cfl complete set with fitting & instalation 60 watt 2557 three pin multipoint plugtop 6amp 2558 three pin multipoint plugtop 16amp 2559 terminal for battery 12 volt ( brass ) 2560 battery terminal lead 12 mm dia 2561 flexible m.s pipe 25mm dia 2562 isolator 63 amp four way 2563 mcb 63 amp four way 2564 500va invetor assembeld complete accisorieses with cabinet 2565 l.e.d flud light 24 watt ( bajaj ) 2566 l.e.d flud light 60 watt ( bajaj ) 2567 l.e.d flud light 80 watt ( bajaj ) 2568 street pole single arm 3 mtr 2569 street pole single arm 15 mtr 2570 street pole double arm 15 mtr 2571 pole for high mast light with 8 way bracket height 60 feet 2572 pole for high mast light with 12 way bracket height 60 feet 2573 pole for high mast light with 4 way bracket height 30 feet 2574 l.e.d bulb 5 watt ( bajaj ) 2575 l.e.d bulb 7 watt ( bajaj ) 2576 l.e.d bulb 12 watt ( bajaj ) 2577 l.e.d bulb 25 watt ( bajaj ) 2578 l.e.d tube light fitting complete 18 watt 2579 l.e.d tube light fitting complete 9 watt 2580 stree light led 25 watt complete with all acc. 2581 stree light led 40 watt complete with all acc. 2582 kit kat fuse 32 amp f / t 2583 condensor 2.15 mfd 2584 condensor 60 / 70 mfd 2585 pvc gang box 4 way 2586 pvc gang box 6 way 2587 pvc gang box 8 way 2588 pvc gang box 10 way 2589 pvc gang box 12 way 2590 complete tube light fitting 40 watt 2591 condensor 100 / 120 mfd 2592 double element of 35 watt for soldering iron 2593 solder wire 80:20 2594 soldering paste ( 7 gm. ) 2595 hook up wire transisterised 24 swg 2596 ba type nut bolt 1 / 2 2597 diode in 4007 2598 speaker 4 ohm 2599 araldite 100 gm. 2600 quick fix 10 gm. tube 2601 fevi quick ( elfi ) 2602 multimedia speaker 2603 flair nut 1 / 4 2604 copper brazing rod s 2605 brazing flux 2606 thermostatic switch ( defrost type for fridge ) 2607 capillary tube 1 / 64 2608 capillary tube 1 / 32 2609 thermostatic switch for ac 2610 relay ( for refrigerator 1 / 6 hp ) 2611 relay ( for refrigerator 1 / 8 hp ) 2612 relay ( for ac ) 1 ton 2613 relay ( for ac ) 1.5 ton 2614 compressor oil 2615 refrigerant ( f 12 ) 2616 refrigerant ( f 22 ) 2617 gaskit for compressor 1 / 64 2618 black board ( wall hanging type folding cavas ) standard size 2619 mouse pad for computer 2620 gas kit 1 / 32 for air conditioner compressor packing paper 2621 narial seenk jhadu 2622 phool jhadu 2623 harpic 500 ml 2624 odonil 2625 phenyl 5 ltr pack dr. brand 2626 phenyl balls 2627 toilet cleaning brush iron handle 2628 wiper in steel handle 2629 jala brush with steel pipe 2630 finit 2631 finit pump 2632 detergent soap 250 grm rin 2633 detergent washing powder 1000 grm rin 2634 toilet soap lifebuoy 2635 torch cell eveready ( battery 1050 leak proof ) 2636 hand wash liquid lifebuoy 200 ml 2637 towel large size office use white 2638 towel medium size office use white 2639 bone china plate full size 2640 bone china plate half size 2641 bone china plate quarter size 2642 spoon steel for lunch 2643 bone china cup plate set ( set of 6 pieces ) 2644 tumbler glass for office use 2645 plastic bucket 15 ltr 2646 plastic jug 2 ltr 2647 balti gi sheet capacity 10 ltr 2648 executive office bag large size 2649 umbrella folding type superior quality 2650 scotch brite 2651 mortine liquid machine 2652 mortine liquid refill 2653 tape measuring 200 mtr in case 2654 white plastic container 10 ltr 2655 plastic container 50 ltr for diesel 2656 table glass 5x3 thickness 10mm 2657 tapastic cloth 2658 corten rod 1 ¼ steel 2659 plastic ring for corten rod 2660 cleanser 100 ml 2661 toner `100 ml 2662 scrub 100 ml 2663 massage cream 250 ml 2664 mask 2665 face pack 2666 rose water 200 ml 2667 gel 200 ml 2668 moisturizer 100 ml 2669 sunscreen 100 ml 2670 cotton bubs 2671 facial wiper 2672 cotton 2673 sanitizer 100 ml 2674 shampoo 200 ml 2675 conditioner 200 ml 2676 pre perm shampoo 100 ml 2677 perming lotion 100 ml 2678 neutralizing lotion 100 ml 2679 porosity fillers 2680 perm end paper / wraps 2681 rubber bands 2682 perming cap 2683 neck trays 2684 portal 2685 gloves 2686 hair per lighteners 2687 hair colours ( basic, fashion, highlight ) 2688 developer 200 ml 2689 post color shampoo 100 ml 2690 aluminum foils 2691 highlight caps with crochet needles 2692 protective cream 100 ml 2693 tail combs 2694 bob pin different size 2695 jura pin different size 2696 invisible pin 2697 decoretive pin 2698 wide comb 2699 styling comb 2700 wing 2701 hair switches 2702 hair stuffing round, small, oblong 2703 false hairs for different length 2704 sprays 100 ml 2705 mousse 2706 styling gels 200 ml 2707 styling serums 100 ml 2708 rebounding cream 200 ml 2709 rebounding board 2710 primer 200 ml 2711 base foundation as 200 ml 2712 supra normal 100 ml 2713 drema oily skin 100 ml 2714 liquid foundation 100 ml 2715 mousse foundation 100 ml 2716 pan cake 2717 pan stick 2718 loose powder 500 gm 2719 compact poweder 2720 eyeshadow pallete 2721 shimmer 2722 glitte 50ml 2723 eyeliner liquid, gel, water liner 2724 kajal / kohl 2725 eye brow pencils / powder 2726 eye pencils 2727 mascara 2728 blush palette 2729 lip palette 2730 lip pencil 2731 lip gloss 2732 make up sponge 2733 make up remover 2734 body paints 2735 accessories diamonds, studs 2736 bindis 2737 heena cone 2738 safety pins 2739 manicure pedicure shampoo 100 ml 2740 hydrogen peroxide 100 ml 2741 pedicure salt 2742 cuticle cream 100 ml 2743 manicure pedicure massage cream 200 ml 2744 manicure pedicure massage oil 200 ml 2745 paraffin wax 200 gm 2746 gauze 2747 cellophane sheet 2748 petrolium jelly 50 gm 2749 base coat 2750 nail varnish remover 2751 nail varnish remover 2752 top coat 2753 postal colors 2754 stone bindis 2755 nail art stickers 2756 nail art sealer 2757 studs 2758 hair oil 200 ml 2759 cold wax / hot wax 01 kg 2760 warm wax 1 kg 2761 thread ( 40 coat ) 2762 talcum powder 200 gm 2763 astringent lotion 100 ml 2764 dettol / savlon 100 ml 2765 waxing strips ( disposable ) 2766 depilatory cream 100 ml 2767 katori wax 200 gm 2768 boric acid 200 gm 2769 alcohol 200 ml 2770 formallin 200 ml 2771 scrub / exfoliators 200 ml 2772 manicure / pedicure pack 2773 borax powder 200 gm 2774 glycerin 200 ml 2775 national styling spray 200 ml 2776 hair rescue treatment mask 2777 deep cleansing shampoo 200 ml 2778 head band 2779 big towel 2780 face towel 2781 hand towel 2782 bed sheet 2783 bath robs 2784 aprons 2785 capes 2786 sewing machine niddle 14, 16 & 18 no. 2787 matching real 200 meter polyster 2788 rashmi real 2789 white real 1000 meter 2790 rubia cloth light colour 2791 popline cloth coloured 2792 tapastic cloth 2793 hand niddle 7, 9 no. 2794 stenner different colour 2795 oil bond 2796 distemper 2797 weather coat 2798 putty 2799 primer for wooden 2800 putty patta 2801 putty patty 2802 primer for iron 2803 primer for wall 2804 thinner 2805 tarpeen oil 2806 sand paper 2807 emery paper 2808 white cement 2809 plaster of paris 2810 synthetic paint 2811 oil paint 2812 lime stone 2813 roller flatter 2814 wall masta 2815 emery cloth 2816 paint brush flat 0 to 12 no. 2817 paint brush flat 1 2818 paint brush flat 2 2819 paint brush flat 3 2820 paint brush flat 4 2821 paint brush flat 5 2822 paint brush flat 6 2823 angle cock 2824 connection pipe 18” 2825 connection pipe 24” 2826 pipe 1” 2827 union 1” 2828 tee 1” 2829 1x9” nipple 2830 1x6” nipple 2831 1x4” nipple 2832 1x2” nipple 2833 1x1 / 2” bush 2834 sistern handle 2835 sistern 2836 basin toti 2837 waste pipe 2838 union pipe 2839 union cap 2840 safeda big 2841 dhaga 2842 sistern rubber 2843 long band 2844 connection washer 2845 acrylic sheet 10mm 2846 alluminium rods20 mm se 30 2847 alluminium rods 25mm se 30 2848 alluminium block 80x80x10 mm 2849 alluminium sheet 10 mm 2850 m.s flat 2851 m.s rod 2852 gi pipe b grade 1 / 2 dia 2853 gi pipe b grade 3 / 4 dia 2854 gi pipe b grade 1 dia 2855 gi socket 1 / 2 2856 gi tee 1 / 2 2857 gi bend 1 / 2 2858 gi union 1 / 2 2859 gi hex nipple 1 / 2 2860 gi socket 3 / 4 2861 gi tee 3 / 4 2862 gi bend 3 / 4 2863 gi union 3 / 4 2864 gi hex nipple 3 / 4 2865 gi socket 1 2866 gi tee 1 2867 gi bend 1 2868 gi union 1 2869 gi hex nipple 1 2870 wooden plank 50mm x 25 mm x 1 m 2871 wooden plank 100mm x 25 mm x 1 m 2872 ms gas welding filler rod 2873 wire cut clay bricks 2874 river sand afs no.100 ~ 40 2875 ston aggregate 2876 cement portland 2877 copper tubes 6 mm dia, 25 mm dia 2878 copper brazing filler rod 2879 pvc pipes heavy duty 1 / 2 2880 pvc pipes heavy duty 3 / 4 2881 pvc pipes heavy duty 1 2882 pvc pipes heavy duty 1 1 / 2 2883 pvc pipes heavy duty 2 2884 pvc pipes heavy duty 4 2885 pvc pipes heavy duty 6 2886 pvc pipe light duty 1 / 2 2887 pvc pipe light duty 3 / 4 2888 pvc pipe light duty 1 2889 pvc pipe light duty 1 1 / 2 2890 pvc pipe light duty 2 2891 pvc reducer 1 / 2 2892 pvc plain coupling 1 / 2 2893 pvc tee 1 / 2 2894 pvc bend 1 / 2 2895 pvc elbow 1 / 2 2896 pvc mta 1 / 2 2897 pvc fta 1 / 2 2898 pvc socket 1 / 2 2899 pvc reducer 3 / 4 2900 pvc plain coupling 3 / 4 2901 pvc tee 3 / 4 2902 pvc bend 3 / 4 2903 pvc elbow 3 / 4 2904 pvc mta 3 / 4 2905 pvc fta 3 / 4 2906 pvc socket 3 / 4 2907 pvc reducer 1 2908 pvc plain coupling 1 2909 pvc tee 1 2910 pvc bend 1 2911 pvc elbow 1 2912 pvc mta 1 2913 pvc fta 1 2914 pvc socket 1 2915 pvc reducer 1 1 / 2 2916 pvc plain coupling 1 1 / 2 2917 pvc tee 1 1 / 2 2918 pvc bend 1 1 / 2 2919 pvc elbow 1 1 / 2 2920 pvc mta 1 1 / 2 2921 pvc fta 1 1 / 2 2922 pvc socket 1 1 / 2 2923 pvc reducer 2 2924 pvc plain coupling 2 2925 pvc tee 2 2926 pvc bend 2 2927 pvc elbow 2 2928 pvc mta 2 2929 pvc fta 2 2930 pvc socket 2 2931 pvc reducer 4 2932 pvc plain coupling 4 2933 pvc tee 4 2934 pvc bend 4 2935 pvc elbow 4 2936 pvc mta 4 2937 pvc fta 4 2938 pvc socket 4 2939 pvc reducer 6 2940 pvc plain coupling 6 2941 pvc tee 6 2942 pvc bend 6 2943 pvc elbow 6 2944 pvc mta 6 2945 pvc fta 6 2946 pvc socket 6 2947 c.pvc pipe 20 mm dia 2948 ppr pipe 20mm dia 2949 g.i pad lock 65 mm 2950 g.i pad lock 80 mm 2951 exhaust fan 18 2952 inverter 5 kva 2953 battery tubular 150 ah 2954 inverter 3.5 kva 2955 battery stand 4 battery 2956 battery smf 7 ah 2957 ac sanitary pipe coupling 100 mm dia 2958 ac pressure pipe coupling 100 mm dia 2959 ci water supply pile bell and spigot end 2960 ci water supply pipe flanged end 2961 pvc ball valve 2962 lubricating oil 2963 oxygen gas 2964 acetylene gas 2965 water meter 2966 aqua fresh purifire 5 microns cap. 5 ltr. 2967 aqua fresh purifire 5 microns cap. 40 ltr. 2968 commercial purifier / ro cap. 400 ltr 2969 photocopy paper a4 size 2970 photocopy paper a3 size 2971 photocopy paper legal size 2972 toner cartage 2973 pen drive 8 gb 2974 pen drive 16 gb 2975 cat 5 / 5e cable 2976 cds 2977 cellotape / brown tape 2978 cloth duster 2979 colin 2980 correcting fluid ( white ) 2981 cutter 2982 dustbin 2983 duster cloth ( 2’ by 2’ ) 2984 dvds 2985 engine coolant 2986 engine oil 2987 eraser 2988 fevi stick 2989 key board ( usb / ps2 ) 2990 paper wet 2991 pilot pen 2992 dot pen 2993 scale 12 2994 scale plastic 24” 2995 scetch pen colour 2996 scissor paper cutting 2997 sharpner 2998 short hand note book 2999 short hand pencil 3000 smps 3001 stapler big 3002 stapler small 3003 stepler pin ( small size ) 3004 stepler pin ( big size ) 3005 wall clock 3006 full scape paper ( white ) 3007 drawing pencil ( hb, 2b, 4b, 6b ) 3008 poster color ( set of 12 colors ) 3009 rotary switch 16 a ( raw material ) 3010 curtain / blinds for lab 3011 water color ( set of 12 colors ) 3012 office bag 3013 gum bottle 3014 all pin 3015 pin cusion 3016 hand sanitizer 3017 dustbin commercial type 3018 file cover 3019 file folder 3020 calculator 12 digit 3021 white board marker 3022 permanent marker 3023 duster magnetic type 3024 chawk 3025 taper table stand 3026 electric kettle 3027 electric bell 3028 bin card 3029 room freshner 3030 pocha big size 3031 toilet brush 3032 tray set of 3 pcs 3033 indent book 3034 stock register 3035 register rulled 1 quire 3036 register rulled 2 quire 3037 register rulled 4 quire 3038 register rulled 6 quire 3039 exaust 250 mm 3040 exaust 200mm 3041 torch 3 cell eveready 3042 lathi 3043 visitor chair 3044 principal chair executive 3045 side table for principal chair 3046 center table 3047 office sofa 3 seater 3048 office sofa 1 seater 3049 3 seater sofa chrome type 3050 cctv for iti campus 3051 water cooler 80 / 120 3052 water cooler 60 / 80 3053 file rack with 3 drawer 3054 synages for diff lab & class rooms 3055 photocopy machine comercial type 3056 wall fan...

Directorate of Training and Employment - Uttar Pradesh

23599530 supply of tools and equipments 1 desktop computer cpu: 32 / 64 bit i3 / i5 / i7 or latest processor, speed: 3 ghz or higher. cache memory: minimum 3 mb or better. ram: 8 gb ddr iii or higher. hard disk drive: 500gb or higher, 7200 rpm ( minimum ) or higher, wi fi enabled. network card: integrated gigabit ethernet ( 10 / 100 / 1000 ) wi fi, usb mouse, usb keyboard and monitor ( min. 17 inch ) , standard ports and connectors. dvd writer, speakers and mic. licensed windows operating system / oem pack ( preloaded ) , antivirus / total security 2 laptop 4th gen ci5 or higher processor, 4gb ram, 1tb hard disk, win8 / latest preloaded licensed os, 2gb graphics card, dvd writer, standard ports and connectors. 3 wi–fi router with wireless connectivity 4 switch 24 port 5 structured cabling in lab to enable working with wired networks for practical 6 registered domain at least 100 mb web space 7 optical scanner flatbed a4 8 digital web cam high resolution ( 3.1 mp or higher ) 9 dvd or blu ray writer 24x or higher external ( usb ) 10 crimping tool rj 45 11 network rack 4u for 24 port 12 digital multimeters 3.5 digit handheld type. 13 external hard disk 1 tb 14 patch panel 24 port 15 lan tester utp cat5 cable tester ( rj 45 ) 16 punching tool for punching rj 45 socket with cat 5 cable 17 gimp / irfanview image editor or equivalent latest version 18 web authoring tool wysiwyg web authoring tool dreamweaver or open source tools like kompozer, frontpage or similar tools along with ftp tools for ex. filezilla etc. 19 e commerce simulation software latest version 20 vacuum cleaner hand held 21 chair and table for the instructor with armrest mounted on castor wheels, adjustable height / standard 22 computer table laminated top 150x650x750 mm with sliding tray for key board and one shelf of storage 23 air conditioner split type 1.5 tons 24 duster cloth 2’ / 2’ 25 full scape paper white 26 cartridges for printer colour / monochrome as per model of the printer 27 i / o box with socket rj 45 28 rj 45 connector for connecting utp cat 5 cable 29 smps 12v dc 30 cmos batteries 3.0 v 31 power chord 3 pin 32 cable cat 5 / 5e 33 power adapter for hub, switch, router 34 box drawing instrument containing one 15 cm compass with pin point, pin point & lengthening bar, one pair spring bows, rotating compass with interchangeable ink and pencil points, drawing pens with plain point & cross point, screw driver and box of leads. ( 0.2, 0.3, 0.4mm ) . 35 protractor celluloid 15 cm semi circular. 36 scale card board metric set of eight a to h in a box 1: 1, 1:2, 1:2:5, 1: 5, 1:10, 1:20, 1:50, 1:100, 1:200, 1:500, 1:1000, 1:2000, 1:1250, 1:6000, 1:381 / 3, 1:66 2 / 3 37 scales plotting box wood 6 metric scales 30 cms long withoffset scales. 38 set square transparent 20 cm, 2 mm thick with bevellededges 45 degree . 39 set square celluloid 25 cm, 2mm thick with bevelled edges60 degrees. 40 t square 750mm / mini drafter / parallel bar 41 template –architects and builders 42 geometrical models ( wooden / plastic ) i ) cube 08 cm sides. ii ) rectangular parallel piped 8cm x 15cm iii ) sphere 8cm dia. iv ) right circular cone 8 cm dia base and 15 cm vertical height v ) square pyramid 8cm side base and 15 cm vertical height vi ) cylinder 8 cm dia. 15 cm height.vii ) prisms triangular 8 cm sides triangle and 15 cm length. viii ) prism hexagonal 8 cm side’s hexagon and 15 lengths 43 templates – circle, ellipse, furniture, etc. 44 calculator scientific ( nonprogrammable ) 45 proportional dividers 15 cm 46 land measuring chain 30 metres with two handles 47 ranging rod wooden fitted iron shoe 2 mt. long 48 prismatic compass with stand 110 mm dia. 49 plane table with stand with accessories – alidade, trough compass, spirit level ( 6 ) , u – fork, plumb bob, etc 50 telescopic alidade 51 dumpy level with all accessories 52 auto level with all accessories 53 levelling staff 4 mt. leading to 5 mt. telescopic type 54 transit theodolite with stand with all accessories 55 digital theodolite latest model with all accessories ( features: based on laser technology, two large lcd panel with easy to read , automatically compensates tilt in two direction and compensates vertical angles. high integrated electronic board and ic elements ) 56 instrument for total station with latest model, with all accessories graphic lcd display on both side.multy function key board on both side. able to interchange data between gps and total station without any data conversion. minimum 8 hours rechargeable li ion battery .poles and prism 2nos each 57 hand held gps ( latest model ) with standard specification 58 cad software 59 broad band connection 60 ups 61 computer table 62 dlp projector 2000 lumens or higher 63 air conditioner 2.0 ton 64 document camera / visualiser 65 chair for trainer / instructor 66 class room chairs ( armless ) 67 class room table single / dual desk 68 drawing table with board 750mm x 550mm 69 measuring steel tape 5 meter 70 combination plier insulated 200 mm 71 screw driver insulated 4mm x 150 mm, diamond head 72 punch centre 9mm x 150 mm 73 neon tester 500 v 74 hammer, cross peen with handle 250 grams 75 pincer 150 mm 76 c clamp200 mm and 100 mm 77 spanner adjustable drop forged, ss 150 mm & 300mm 78 chisel cold 25 mm x 200 mm 79 chisel firmer with wooden handle 6 mm x 200 mm 80 allen key alloy steel 1.5 10 mm ( set of 9 ) 81 grease gun 0.5 ltr. capacity 82 bradawl 83 pully puller with 3 legs 150 mm & 300mm 84 bearing puller ( inside and outside ) 200 mm 85 pipe vice cast iron with hardened jaw open type 100 mm 86 scissors blade, ss 200mm 87 scissors blade, ss 150 mm 88 crimping tool 1.5 sq mm to 16 sq mm, 89 wire cutter and stripper150 mm 90 mallet hard wood 0.50 kg 91 hammer extractor type 250 grams 92 hacksaw frame adjustable 300 mm fixed 150 mm 93 try square 150 mm blade 94 divider 150 mm spring type 95 pliers long nose insulated 150 mm 96 pliers flat nose insulated 200 mm 97 pliers round nose insulated 100 mm 98 tweezers 150 mm 99 snip straight and bent heavy duty 250 mm 100 d.e. metric spanner double ended 6 32 mm 101 drill hand brace 0 100mm 102 drill s.s. twist block 2 mm, 5 mm and 6 mm set of 3 103 plane cutters 50 mm x 200mm 104 smoothing cutters 50 mm x 200mm 105 gauge, wire imperial stainlees steel marked in swg & mm wire gauge metric 106 file flat 200 mm 2nd cut with handle 107 file half round 200 mm 2nd cut with handle 108 file round 200 mm 2nd cut with handle 109 file flat rough 150 mm with handle 110 file flat bastard 250 mm with handle 111 file flat smooth 250 mm with handle 112 file rasp, half round 200 mm bastard with handle 113 de soldering gun heat proof nozzle, pvc type, 250mm 114 table vice 100 mm jaw 115 contactor & auxiliary contacts 3 phase, 415 volt, 25 amp with 2 no and 2 nc 116 rotary switch 16 a / 440v 117 pin type, shackle type, egg type & suspension type insulators including hardware fitting 118 hydrometer 119 hand drill machine 0 6 mm capacity 120 portable electric drill machine 0 12 mm capacity 750w, 240v with chuck and key 121 load bank ( lamp / heater type ) 6 kw, 3ph 122 brake test arrangement with two spring balance rating 0 to 25 kg 123 thermometer digital 0° c 150° c 124 series test lamp 230v, 60w 125 knife switch tpdt fitted with fuse terminals 16 amp / 440 v 126 mccb 100amps, triple pole 127 elcb and rccb 25amps, double pole and 25amps, double pole, iδn 30 ma 128 various lamps halogen incandescent lamp fluorescent tube hp mercury vapor lamp high pressure sodium lamp low pressure sodium lamp led 129 plug socket 230 v, 5 a 130 lamp holder 230 v, 5 a 131 cables : twisted pair non metallic sheathed cable underground feeder cable ribbon cable metallic sheathed cable multi conductor cable coaxial cable direct buried cable 1 mtr each 132 safety belt standard quality 133 ohm meter; series type & shunt type, portable box type 50 / 2000 ohm analog 134 tachometer analog type 10000 rpm 135 megger analog 500 v 136 3 point d.c. starter for 2.5 kw dc motor 137 4 point d.c. starter for 2.5 kw dc motor 138 phase sequence indicator 3 phase, 415 v 139 growler 230 v, 50 hz, single phase, adjustable jaws, testing armature with ampere meter and testing probes. 140 oscilloscope dual trace 20 mhz 141 soldering iron 65 watt 142 b. electric kettle b. 1500 watts, 240v 143 f. geyser ( storage type ) f. 10 litre 144 h. washing machine semi automatic h. 5 kg, 145 i. motor pump set i. 1 hp, 1 phase, 240 v 146 inverter with battery 1 kva with 12 v battery input 12 volt dc, output 220 volt ac 147 voltage stabilizer ac input 150 250 v, 600 va ac output 240 v, 10 a 148 solar panel with battery 18 watt 149 d.c. shunt generator with control panel d.c. shunt generator with control panel, 2.5 kw, 220v &3phase squirrel cage induction motor, 5hp, 440v with control panel & star delta starter 150 motor generator ( ac to dc ) squirrel cage induction motor with star delta starter and directly coupled to dc shunt generator and switch board mounted with regulator, air breaker, ammeter, voltmeter, knife blade switches and fuses, set complete with case iron and plate, fixing bolts, foundation bolts and flexible coupling. induction motor rating: 7.5 hp, 415v, 50 cycles, 3 phase. dc shunt generator rating: 5 kw, 440v ( output voltage varies 110 440v ) 151 d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker, 2.5 kw, 220v &3phase squirrel cage induction motor, 5hp, 440v, with control panel & star delta starter 152 dc series motor coupled with spring balance load 2.5 kw, 220 volts 153 dc shunt motor 2.5 kw, 220 v 154 dc compound motor with starter and switch 2.5 kw , 220 volts 155 ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse with mechanical load. 5 hp, 3 phase, 415 v, 50 hz 156 universal motor with starter / switch 240 v, 50 hz, 1 hp 157 thyristor / igbt controlled d.c. motor drive with tacho generator feedback arrangement 1 hp 158 electrical machine trainer – suitable for demonstrating the construction and functioning of different types of dc machines and ac machines ( single phase and three phase ) . should be fitted with friction brake arrangement, dynamo meter, instrument panel and power supply unit 159 diesel generator set with change over switch, over current breaker and water / air cooled with armature, star delta connections ac 3 phase 7.5 kva, 415 volt or higher rating 160 used dc generators series, shunt and compound type for overhauling practice 161 motorised bench grinder 1 hp. 3 phase, 440v with dol starter, double side with smooth and rough wheel with tool base 162 a.c. series type motor 1 hp, 240 v, 50 hz 163 single phase capacitor motor with starter switch 1 hp, 240 v, 50 hz 164 manual motor coil winding machine with step arbor 165 ceiling fan coil winding machine 250v, 50 hz, 1 ф, with speed control 166 primary current injection set 220v, 50 hz, 1 ф, output current 200 a ( min ) with timer 167 stepper motor with digital controller 168 shaded pole motor fractional hp, 240 v, 50 hz 169 working bench 2.5 m x 1.20 m x 0.75 m 170 different types of analog electronic components, digital ics, power electronic components, general purpose pcbs, bread board, mcb, elcb 171 dso ( colour ) 4 channel , 50mhz real time sampling 1g samples / sec, 12 mpts memory with pc interface usb, lan and math function includes +, , fft, differential, integral, abs, log etc. 172 soldering & de soldering station 173 smd soldering & de soldering station with necessary accessories 174 dol starter 175 ac motor trainer kit ¼ hp motor single phase contactors relays mcb dol starter 176 frequency modulator and demodulator trainer kit fm modulator type : reactance modulator, varactor modulator, vco based modulator fm demodulator type all 5 demodulation techniques detailed teaching and learning contents through software 177 microcontroller kits ( 8051 ) along with programming software ( assembly level programming ) core 8051, ready to run programmer for at89c51 / 52 & 55, programming modes key pad and pc circuits. detailed learning content through simulation software. 178 application kits for microcontrollers 6 different applications 1. input interface : 4x4 matrix keypad, ascii key pad, four input switch 2. display module 16x2 lcd, seven segment, led bar graph 3. adc / dac module with most popular dc / dac0808 4. pc interface: rs232 & usb 5. motor drive: dc, servo, stepper 6. daq: data acquisition to sense different sensors signals 179 sensor trainer kit containing following sensors 1. thermocouple 2. rtd 3. load cell / strain gauge 4. lvdt 5. smoke detector sensors 6. speed sensor 7. limit switch 8. photo sensors 9. optocouplor 10. proximity sensor graphical touch lcd with inbuilt processor for viewing the output waveforms, in built daq, and standard processing circuits like inverting , non – inverting , power, current , instrumentation differential amplifier, f / v, v / f, v / i, i / v converter, sensors :rtd, ntc thermistor, lm35 thermocouple, gas ( smoke ) sensor, load cell, lvdt sensor, speed sensor 180 various analog and digital ics useful for doing project works mentioned in the digital and analog ic applications modules 181 different types of electronic and electrical cables, connectors, sockets, terminations. 182 fiber optic communication trainer full duplex analog & digital trans receiver with 660nm & 950nm, noise generator with variable gain, four seven segment display ber counter, eye 183 seven segment dpm trainer 184 lcd based dpm 185 ups trainer pwm switching technology, test points to measures the voltages of different sections overall functioning of ups trainer, avr transformer, ups with load condition 186 lcd tv ( trainer kit ) 21 inch full hd lcd color television should support pal / ntsc video formats complete block diagram of a lcd tv system, study board indicating various sections of lcd tv along with the test points and switch faults 187 lcd tv ( 21” ) 188 led tv ( trainer kit ) 20 inch full hd led color television, pal / ntsc video formats, complete block diagram of a led tv system , study board indicating various sections of led tv along with the test points and switch faults trouble shooting in different sections. 189 home theatre system 190 solar training kit / simulator with built in meters for dcv, dca, ac multifunction meter ( for aci, acv, power, frequency ) , protection circuits, bs 10 terminals for making the connection, single / dual axis tracking system charge controller : pwm based mppt, charging stage : bulk, absorptions and float 191 led lighting system measurement of power, voltage, current, power factor and light output performance of different lighting products like led, cfl at variable input voltages 0 to 245v variable ac 192 connecting screwdriver 10 x 100 mm 193 screw driver set set of 7 194 insulated combination pliers 150 mm 195 electrician knife 100 mm 196 digital multimeter ( 3 3 / 4 digit ) , 4000 counts 197 de soldering pump electrical heated, manual operators 230 v, 40 w 198 plier flat nose 150 mm 199 battery charger 0 6 9 12 24 48 v, 30 amp 200 function generator ( dds technology ( sine, square, triangle, ramp, pulse, serial data, ttl and modulation. ) 1 mhz 10 mhz function pulse – modulation generator with built in 40mhz frequency counter 201 autotransformer 15 amps 202 op amp trainer 203 digital ic trainer breadboard for circuit design with necessary dc power supply, graphical lcd, clock frequency 4 different steps, data switches: 8 nos, led display: 8 nos. ( ttl ) , seven segment display, teaching simulation software 204 computers in the assembled form ( including cabinet, motherboards, hdd, dvd, smps, monitor, kb, mouse, lan card, blu ray drive and player ) , ms office education version 205 electronic circuit simulation software with 6 user licenses circuit design and simulation software with pcb design with gerber and g code generation, 3d view of pcb, breadboard view, fault creation and simulation. 206 steel rule with metric & british graduation 150 mm, stainless steel 207 caliper hermaphrodite spring type 150mm 208 centre punch 10 mm and length 120 mm 209 screw driver 150mm insulated flat type 210 chisel cold flat 20 mm x 150 mm high carboon steel 211 wing compass. 254 mm or 300 mm 212 hand hammer with handle. 1000 gm 213 torque wrench ( standard / ratchet type ) 14 to 68 nm 214 power tools for fastening capacity 10 18mm 215 different profile gauges ( plate type ) for demonstration metric standard 216 knurling tool ( diamond, straight & diagonal ) 217 indexable boring bar with inserts 1 shank 218 temperature gauge range 0 150°c 219 dowel pin ( straight ) dia. 1 length 4 ( mat: stainless steel ) 220 standard tap screws m3, m4, m5, m6, m8, m10, m12, m14, m16 221 lapping plate dia. 6 222 caps screws m6, m8, m10, m12 223 drill gauges letter drill gauge ( a to z ) , number drill gauge ( 1 to 60 ) , metric drill gauge ( 1.5mm to 12.5mm, 30 holes ) 224 cast iron globe valve ( flanged type ) 150nb, class# 150 flange:ansi125 b16.1 225 c.i. sluice / gate valve ( flanged type ) 150nb, class# 150 flange:ansi125 b16.1 226 stop cock 25nb ( 2 way, threaded end ) 227 hammer ball peen with handle. 220 grams ( 1 / 2 lb ) 228 slip on forged steel flange 150nb, ansi b16.5, class#150 229 bolt & nut with washer ( may be manufactured inhouse ) m20x2.5x90long ( part thread hex. head ) 230 pipe threading die with handle ratchet type die head of 1 / 2 , 3 / 4 and 1 231 jigs & fixture ( sample ) for demonstration ( may be manufactured in house ) 232 m. s. shaft ( may be manufactured in house ) bright m.s. round bar 80mm, 600mm long, stepped 0mm on 300mm one end 233 pulleys ( for v belt or flat belt ) to fit on 50mm dia.shaft with key slot 234 steel keys ( may be manufactured in house ) to fit with keyslot of shaft & pulley 235 damaged old spur gear to fit 50mm dia. shaft 236 v belt and flat belt to fit on pulley 237 packing gasket ptfe gasket roll small size 238 washer, clutch, keys, jib, cotter & circlip minimum 25mm size, carbon steel material 239 hollow punch straight shank hollow punch sets 5 12mm 240 drill drift ( may be manufactured in house ) 200mm hardened and black finish 241 bearing different types each type of diameter 25mm ( min. ) 242 lifting sling 8mm nominal dia. single leg sling 243 bearing extractor universal gear puller 2 or 3 jaws adjustable 244 pulley extractor universal gear puller 2 or 3 jaws adjustable 245 trammel 300mm 246 mallet. dia 100 mm x 150 mm 247 aviation snips straight cut 300mm 248 flat headed hammers with handle. 249 planishing hammer. 250 snip bent left cut 250 mm 251 stake hatchet with leg. 300 x 200 x 20 mm 252 stake grooving. 100 x 100 x 300 mm 253 slip gauge as johnson metric set. 87 pieces set 254 gauge snap go and not go 25 to 50 mm by 5 mm, set of 6 pieces 255 gauge plug single ended 5 to 55 by 5 mm. set of 11 pcs. 256 file half round second cut 150mm 257 gauge telescopic set. 8 150 mm 258 dial test indicator on stand 0.01 mm least count 259 sine bar 125 mm 260 dial verniercaliper. ( universal type ) 0 300 mm, lc 0.05 mm 261 screw thread micrometer with interchangeable. pitch anvils for checking metric threads 60. 0 25 mm lc 0.01 mm 262 depth micrometer. 0 25 mm accuracy 0.01 mm with standard set of extension rods upto 200 mm 263 vernier caliper. 0 150 mm with least count 0.02mm 264 digital micrometer outside. 0 25 mm l.c. 0.001 mm. 265 comparators gauge dial indication with stand and bracket. lc 0.01mm 266 engineers try square ( knife edge ) 150 mm blade 267 surface roughness comparison plates n1 n12 grade 268 digital vernier caliper 0 200 mm l.c. 0.01 mm ( optional ) 269 vernier bevel protector range 360deg, lc. : 5min ( 150mm blade ) 270 carbide wear block. 1 mm 2 mm 271 lathe tools h.s.s. tipped set. 272 lathe tools bit. 6 mm x 75 mm hss / carbide 273 lathe tools bit. 8 mm x 75 mm hss / carbide 274 lathe tools bit. 10 mm x 75 mm hss / carbide 275 arm strong type tool bit holder. right hand 276 arm strong type tool bit holder. left hand 277 arm strong type tool bit holder. straight 278 stillson wrenches 250 mm 279 pipe cutter wheel type. 6 mm to 25 mm 280 pipe bender machine spool type with stand manually operated. up to 25 mm cold bending 281 adjustable pipe chain tonge to take pipes up to 300 mm 282 adjustable spanner. 380 mm long 283 ss and sc centre lathe ( all geared ) with minimum specification centre height 150 mm and centre distance 1000 mm along with 3 & 4 jaw chucks, auto feed system, safety guard, taper turning attachment, motorized coolant system, lighting arrangement & standard accessories. 284 drilling machine bench. sensitive 0 12 mm cap motorized with chuck and key 285 d.e. pedestal grinding machine with wheels rough and smooth 2 h.p. 3phase 415v, 1500 rpm, 250 dia. wheel 286 dot punch 100mm 287 transformer welding set continuous welding current, with all accessories and electrode holder 60% duty cycle with standard accessories 300 a, ocv 60 100 v, 288 welder cable able to carry 300 amps. with flexible rubber cover 289 lugs for cable 290 arc welding table ( all metal top ) with positioner. 1200 x 1200 x 750 mm 291 oxy acetylene gas welding set equipment with hoses, oxygen & acetylene cylenders, regulator and other accessories. 292 gas welding table with positioner with fire bricks 900 x 600 x 750 mm 293 welding torch tips of different sizes for oxy acetylene gas welding to fit nozzel no. 1, 2, & 3 294 trolley for gas cylinders. 295 gloves ( leather ) 296 spindle key for cylinder valve. 297 welding torches. nozzles no. 1, 2, & 3 298 welding helmet with coloured flame retardent glass 299 compressor unit suitable for pressure: 8 bar, delivery: 50 lpm ( or more ) , reservoir capacity: 24 litres ( or more ) , 230v, 50 hz, with pressure regulator and water separator 300 pneumatic trainer kit, each consisting of the following matching components and accessories: i. single acting cylinder max. stroke length 50 mm, bore dia 20 mm 301 ii. double acting cylinder max. stroke length 100 mm, bore dia 20 mm, magnetic type 302 straight edge steel 300 mm or above 303 iii. 3 / 2 way valve manually actuated, normally closed 304 iv. 3 / 2 way valve pneumatically actuated, spring return 305 v. one way flow control valve 306 vi. 5 / 2 way valve with manually operated switch 307 vii. 5 / 2 way valve pneumatically actuated, spring return 308 viii. 5 / 2 way pneumatic actuated valve double pilot 309 ix. 3 / 2 way roller lever valve direct actuation normally closed 310 x. shuttle valve ( or ) 311 xi. two pressure valve ( and ) 312 xii. pressure gauge 0 16 bar 313 spirit level metal type 2 300 mm basic length accuracy 0.1mm / meter 314 xiii. manifold with self closing nrv, 6 way 315 xiv.pushbutton station for electrical signal input with 3 illuminated momentary contact switches ( 1 no + 1 nc ) and 1 illuminated maintainedcontact switch ( 1 no + 1 nc ) , contact load 2a 316 xv. relay station with 3 ralays each with 4 contact sets ( 3no+1nc or change over type ) , 5 a 317 xvi. 3 / 2 way single solenoid valve with led 318 xvii. 5 / 2 way single solenoid valve with manual override and led 319 xviii. 5 / 2 way double solenoid valve with manual override and led 320 xix. power supply unit, input voltage 85 – 265 v ac, output voltage: 24 v dc, output current: max. 4.5 a, short circuit proof. 321 xx. profile plate, anodised aluminium 1100x700 mm, with carriers, mounting frames and mounting accessories ( to be fitted onto the pneumatic workstation ) 322 pneumatic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: ( 1 ) work table – ize ( approx. ) l1200mmxw900mmxh90 0mm, with four castor wheels including two lockable wheels at the front side, ( 2 ) drawer –size ( approx. ) – 460mmxw495mm xh158mm each, and overall size of drawer unit ( approx. ) 470mmxw495mmxh825 mm and ( 3 ) drawer slide height ( approx. ) 85mm. 323 carrier for mounting components, such as pb & relay boxes. 324 stud extractor ezy out set of 8 325 cut section model for pneumatic components 326 hydraulic trainer kit, each consisting of the following matching components and accessories: i. hydraulic power pack with ( 1 ) external gear pump having a delivery rate of 2.5 lpm, ( approx. ) @ 1400 rpm operating pressure 60 bar, coupled to a single phase ac motor ( 230 v ac ) having start capacitor and on / off switch and overload protection, ( 2 ) pressure relief valve adjustable from 0 – 60 bar, ( 3 ) oil reservoir, ≥5 litres capacity having sight glass, drain screw, air filter, and p and t ports. 327 ii. pressure relief valve pilot operated 328 iii. drip tray, steel size 1160 mm x 760 mm. 329 iv. pressure gauge glycerin damped, indication range of: 0 – 100 bar 330 v. four way distributor with five ports, equipped with a pressure gauge 331 vi. double acting hydraulic cylinder with a control cam, piston diameter16 mm, piston rod diameter10 mm, stroke length 200 mm. 332 vii. suitable weight for vertical loading of hydraulic cylinder 333 viii. mounting kit for weight for realizing pulling and pushing load. 334 ix. 3 / 2 way directional control valve with hand lever actuation. 335 x. 4 / 2 way directional control valve with hand lever actuation. 336 xi. 4 / 3 way directional control valve closed centre position, with hand lever actuation. 337 xii. non return valve. 338 xiii. pilot operated check valve pilot to open. 339 xiv.one way flow control valve with integrated check valve. 340 t connector with self sealing coupling nipples nos. ) and quick coupling socket ( 1 no. ) . 341 xvi. profile plate, anodised aluminium, 1100x700 mm, with carriers, mounting frames and mounting accessories ( to be fitted onto the hydraulic workstation ) 342 hydraulic workstation with 40 square mm aluminium profile legs, wooden work surface, one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic panel drawer slide: ( 1 ) work table – size ( approx. ) l1200mmxw900mmxh90 0mm, with four castor wheels including two lockable wheels at the front side, ( 2 ) drawer – size ( approx. ) – l460mmxw495mm xh158mm each, and overall size of drawer unit ( approx. ) l470mmxw495mmxh825 mm and ( 3 ) drawer slide height ( approx. ) 85mm. 343 cut section models for hydraulic components 344 micrometer outside. 0 25 mm 345 lcd projector 346 white board 1200mm x 900mm 347 micrometer outside. 25 50 mm 348 micrometer outside. 50 75 mm 349 micrometer inside with extension rods. accuracy 0.01 mm with extension rods upto 150 mm 350 vernier caliper 150 mm 351 vernier bevel protractor blade with acute angle attachment 300 mm 352 screw pitch gauge metric 0.25 to 6 mm 353 surface plate c.i / granite with stand and cover 600 x 600 mm 354 marking table ( mild steel ) 900x900x900 mm 355 universal scribing block. 220 mm 356 v block pair with clamps 150 x 100 x 100 mm 357 angle plate 150 x 150 x 250 mm 358 punch letter set. 3 mm 359 punch number set. 3 mm 360 portable hand drill ( electric ) 0 to 13 mm capacity 361 drill twist straight shank 3 mm to 12 mm by 0.5 mm h.s.s. 362 drill twist taper shank 8 mm to 20 mm by 0.5 mm h.s.s. 363 taps and dies complete set in box. wit worth 364 taps and dies complete set 5, 6, 8, 10 & 12 mm set of 5 365 file knife edge smooth 150 mm 366 file feather edge smooth 150 mm 367 file triangular smooth 200 mm 368 file round second cut 200 mm 369 file square second cut 250 mm 370 feeler gauge gauge feeler / thickness 0.05 mm to 0.3 mm by 0.05 and 0.4 mm to 1 mm by 0.1 mm 13 leaves 371 file triangular second cut. 200 mm 372 file flat second cut safe edge. 300 mm 373 file flat bastard 200 mm 374 file flat bastard. 300 mm 375 file swiss type needle set of 12, length = 150 mm 376 file half round second cut. 250 mm 377 file half round bastard. 250 mm 378 file round bastard. 250 mm 379 file hand second cut. 150 mm 380 file card. 3x5 size, brass or steel wire 381 pliers combination insulated 150 mm 382 wooden handle forged soldering iron copper 230v, 250 w, 350 gm 383 spanner double ended 6x7, 8x9, 10x11, 12x13, 14x15, 16x17, 18x19, 20x22 384 spanner adjustable 150 mm 385 interchangeable ratchet socket set 12 mm driver, sized10 32 mm set of 18 socket & attachments. 386 double ended tubular box spanner set with tommy bar. a / f 6 25 mm set of 10 tommy bar dia 6, 8, 10, 12, 14, 16 387 glass magnifying 75 mm 388 clamp toolmaker 5 cm and 7.5 cm set of 2. 389 clamp c 100 mm 390 clamp c 200 mm 391 hand reamer set ( tapar pin straight flute ) nominal dia 6, 8, 10, 12, 16mm 392 machine reamer parallel ( helical flute ) 12 16mm set of 5. 393 scraper flat 150 mm 394 scraper triangular 150 mm 395 scraper half round 150 mm 396 chisel cold cross cut & diamond point. 9 mm 150 mm 397 chisel cold flat 9 mm x 100 mm 398 chisel cold round noze. 9 mm x 100 mm 399 pipe wrench 400 mm. 400 adjustable pipe die set bsp cover pipe size 1 or 3 / 4 401 wheel dresser ( one for 4 units ) star / dresser with holder length 150 mm, diamond point 402 machine vice swivel base 100 mm 403 machine vice swivel base 125 mm 404 sleeve drill morse no. 0 1, 1 2, 2 3, 3 4, 4 5 405 vice bench 150 mm 406 fire extinguisher ( for 4 units ) co2 type, 3 kg capacity 407 machine vice. 100mm 408 screw driver set set of 5 409 insulated side cutting pliers 150 mm 410 long nose pliers 150 mm 411 soldering iron 25 w. 240 v 412 tweezers 100 mm 413 soldering iron changeable bits 15 w 414 screw driver 150 mm 415 allen key set set of 9 416 tubular box spanner set of 6 417 continuity tester 418 soldering iron 10 w 419 cold chisel 20 mm 420 scissors 200 mm 421 steel rule 30 cm graduated both in english & metric units 422 hermaphrodite caliper 150 mm 423 centre punch 150 mm 424 cold chisel flat b.p. 0.5 kg 425 file flat 300 mm 426 file flat smooth 200 mm 427 combination plier 150 mm 428 surface plate 400 mm x 400mm grade 429 marking off table 1200 x 1200 x 600 mm high with stand 430 scribing block universal 300 mm 431 v block 100 / 7 – 80 – a 432 try square 300 mm 433 divider spring 200 mm 434 straight edge steel 1 meter 435 straight edge steel 500 mm 436 steel rule 60 cm graduated both in english & metric units 437 screw driver, heavy duty 300 mm with handle 438 hammer lead 1 kg. 439 spindle blade screw driver 100 mm 440 allen hexagonal keys 2.5 to 12 441 spanner d.e. series 2 ( set of 7 pieces ) 442 adjustable spanner 300 mm 443 reduction sleeve morse 1 1, 3 1, 4 1, 4 2, 5 1, 5 2, 6 1, 444 angle plate adjustable 250 x 150 x 175 mm 445 number drills h.s.s. ( parallel shank ) 446 twist drills 3 mm to 13 mm in step of 0.5 mm ( parallel shank ) 447 drill chuck 0 13 mm with taper shank 448 centre drill a 1 to 5 449 grinding wheel dresser ( diamond ) 450 grinding wheel dresser huntington type 451 tap and die set in box metric pitch ( 6 mm to 12 mm ) 452 drill h.s.s. taper shank ( 6 mm to 12 mm in step of 0.5 mm ) 453 needle file set 454 file square 2nd cut 250 mm 455 reamer adjustable 10 mm to 15 mm length 75 mm 456 tool bits h.s.s. 6 mm square 457 tool bits h.s.s. 10 mm square 458 tool bits holder ( armstrong ) l.h 459 tool bits holder ( armstrong ) r.h. 460 assorted tools and bit holders for lathe, shaper, slotter & planner in different shapes and sizes 461 table chuck 75 mm jaw swivel base 462 bench vice 100 mm jaw 463 machine vice 200 mm swivel base 464 machine vice swivel base 150 mm 465 hand vice 50 mm jaw 466 radius turning attachment 467 angle turning attachment 468 compound angle vice ( standard sine ) 469 universal machine vice 100mm 470 universal table angle plate 150 x 150 x 150 471 shaper tool holder turret type to suit the machine 472 base chuck for slotter to suit the machine 473 shaper indexing center to suit the machine 474 knurling tools ( set of 3 ) straight and diamond 475 plier cutting 200mm 476 digital multimeter 0 to 500 v 477 variable resistance box resistors with 220y, 150y, 1ky, 33y, 100y, 1.2y 478 dc battery with cap 9v 479 dual power supply ( 230v, 50hz, fuse 800ma ) 480 solder iron ( 350v ) , solder lead, pcb board ( groove board ) , solder wick 481 inductor ( 400 turns, 200 turns, 600 turns, 1200 turns ) , i core , e core, u core, laminated core 482 relay ( 5v ) , led ( 5v ) 483 function generator bread board ( 230v, 50hz, watts 12va, fuse 150ma ) 484 synchronous motor ( 240v, 60rpm ) , capacitor for synchronous motor ( 0.8mf ± 5% 450vac ) 485 power chord connecting probes, single strand &multi strand wires. 486 sensor kit i. mounting plate 487 ii. power distribution box ( 24v dc, 4a ) 488 iii. counter box ( 10 30v dc / 0.05a ) 489 iv. indication box ( 24v dc ) 490 v. material box 491 vi. inductive sensor ( 10 30 v dc, pnp, no, 5mm ( range ) 492 vii. capacitive sensor ( 10 30 v dc, pnp, no, 2 8mm ( range ) 493 viii. magnetic sensor ( 10 60 v dc , pnp, no, 60mm ( range ) 494 ix. ultrasonic sensor ( 20 30 v dc, pnp, no, 80 300mm ( range ) 495 x. connecting wires 496 xi. motor with control unit ( 24v dc, 1a ) 497 milling cutter cylindrical cutter ø 63 mm, 90 mm length and 27 mm bore diameter 498 milling cutter cylindrical cutter ø 80 mm, 90 mm length and 27 mm bore diameter 499 milling cutter side and face cutter dia 100 x 10 x 27 mm 500 milling cutterside and face cutter dia 100 x 12 x 27 mm 501 milling cutter side and face cutter dia 160 x 10 x 27 mm 502 milling cutter side and face cutter dia 160 x 16 x 27 mm 503 milling cutter side and face cutter dia 200 x 20 x 27 mm 504 milling cutter side and face cutter dia 80 x 8 x 27 mm 505 milling cutter equal angle cutter 45˚ / 100 mm x 27 mm bore dia 506 milling cutter equal angle cutter 60˚ / 100 mm x 27 mm bore dia 507 milling cutter equal angle cutter 90˚ / 100 mm 27 mm bore dia 508 milling cutter double angle unequal cutter 50 x 12 x 27 mm bore dia55˚ 509 milling cutter double angle cutter 50 x 12 x 27 mm bore dia 60˚ 510 milling cutter double angle unequal cutter 63 x 18 x 27 mm bore dia 70˚ 511 milling cutter double angle unequal milling cutter double angle unequal cutter 63 x 18 x 27 mm bore dia 75˚ 512 milling cutter single angle cutter 63 x 18 x 45˚ rh 27 mm bore dia 513 milling cutter single angle cutter 63 x 18 x 45˚lh 27 mm bore dia 514 milling cutter single angle cutter 63 x 18 x 60˚ lh 27 mm bore dia 515 milling cutter single angle cutter 63 x 18 x 60˚rh 27 mm bore dia 516 milling cutter slitting saw cutter ø 75 x 3 x ø 27 mm 517 milling cutter slitting saw cutter ø 100 x 6 x ø 27 mm 518 milling cutter shell end mill ø 50 x 36 x 27 mm, preferably inserted tip type 519 milling cutter shell end mill ø 75 mm x 50 x 27 mm, preferably inserted tip type 520 milling cutter parallel shank end mills ø 6, ø 10 and ø 16 are ( double fluted ) , ø 20 mm & ø 25mm ( four fluted ) 521 milling cutter t slot cutter with parallel shank ø 17.5 x 8 mm width x diameter of shank 8 mm 522 milling cutter convex ø 63 x 6 radius x 27 mm bore diameter 523 milling cutter disc type form ( involutes form 2 module, 20°pressure angle ) 524 micrometer outside 0 25 mm reading 0.01 mm with nabl accredited lab. certificate 525 micrometer outside 25 50 mm reading 0.01 mm with nabl accredited lab. certificate 526 micrometer outside 50 75 mm reading 0.01 mm with nabl accredited lab. certificate 527 micrometer outside 75 100 mm reading 0.01 mm with nabl accredited lab. certificate 528 micrometer depth gauge 0 200 mm reading 0.01 mm with nabl accredited lab. certificate 529 digital micrometer 0 25 mm reading 0.01 mm with nabl accredited lab. certificate 530 direct reading vernier caliper 0 300 ( direct reading with dial ) 531 digital vernier caliper 0 300 mm 532 vernier height gauge q 250 mm 533 vernier gear tooth caliper 534 vernier bevel protractor with 150 m blade 535 bevel gauge 200 mm 536 telescopic gauge 8 mm to 150 mm 537 universal dial test indicator plunger type range 0 10 mm, graduation 0.01 mm complete with clamping devices and magnetic stand 538 gauge slip box metric 87 pieces set 539 gauge screw pitch metric 0.25 to 6 mm 540 limit plug gauges 5 mm to 25 mm by 2.5 mm 541 ring gauges 5 mm to 25 m by 2.5 mm ( go & no go ) 542 taper gauge m.t. no. 1, 2, 3, 4 & 5 543 gauge feeler / thickness 0.05 mm to 0.3 mm by 0.05 and 0.4 mm to 1 mm by 0.1 mm 13 leaves 544 planer gauge standard size 545 magnifying glass 75 mm 546 work bench 2400 x 1200 x 900 mm 547 first aid box 548 slotter 180 mm stroke ( motorized ) with all attachments, motor capacity 0.75 kw 549 ss and sc centre lathe ( all geared ) with specification as: centre height 150 mm and centre distance 1000 mm along with 4 jaw chuck, taper turning attachment, steadies, auto feed system, safety guard, motorized coolant system, with lighting arrangement and set of lathe tools, motor capacity 5.5 kw 550 tool and cutter grinder 250 mm to admit 450 m between center fully motorized work head supplied with tool rest of different types table clamps and other attachments, 3.0kw 551 drilling machine pillar 20 mm capacity with drill chuck & key, 0.75 kw 552 radial drill 1200 mm area motorized with tapping attachment, 3.6kw 553 silicon carbide grinder for carbide tipped tools 554 double ended pedestal grinder with 178 mm wheels ( one fine and one rough wheel ) , 0.75 kw 555 universal milling machine with minimum specification as: table length x width 1200 x 300 mm having motorized up & down movement along with auto feed arrangement and with motor capacity 7.5kw following attachments such as: a. vertical head b. slotting attachment c. rack cutting attachment d. rotary table e. dividing head f. adaptors, arbors and collects etc. for holding straight shank drills and cutters from 3 mm to 25 mm. 556 horizontal milling machine with minimum specification as: table length x width 1200 x 300 mm having motorized up & down movement along with auto feed arrangement and 150mm universal vice, motor capacity 7.5kw 557 vertical milling machine with minimum specification as: table length x width 1200 x 300 mm having motorized up & down movement along with auto feed arrangement along with 150mm universal vice, motor capacity 5.5kw 558 surface grinding machine with minimum specification as: grinding machine plain surface, wheel dia. 175 mm ( or near ) with reciprocating table having longitudinal table traverse 200 mm ( or near ) fully automatic and fitted with adjustable traverse stops, machine to be fully motorized and fitted with ace guards and pumps, tank and pump fittings and also to be supplied with magnetic chuck 250 x 112 mm. diamond tool holder, set of spanners, grease gun, oil can and spare grinding wheel for general purpose grinding, motor capacity 3.0 kw 559 cylindrical grinder max. grinding length – 300 mm height of centre – 130 mm max. distance between centers – 340 mm 560 a ) simulator 561 hammer ball peen 0.5 kg with handle 562 spanner d.e. set of 12 pieces 6mm to 32mm 563 spanner, ring set of 12 metric sizes 6 to 32 mm. 564 alternator for tractor different type 565 ammeter 300a / 60a dc with external shunt 566 anvil 50 kgs with stand 567 carburetor repair tool kit 568 chain pulley block 3 ton capacity with tripod stand 569 chaser hard w / v 9 to 40 t.p.i. set of 11 external. 570 circlip pliers expanding and contracting type 15cm and 20cm each 571 clamps c 150mm 572 clutches, different types such as cone type, disc type 573 compression testing gauge suitable for diesel engine 574 cut section model of fuel filter 575 cylinder liner dry & wet liner, press fit & slidefit liner 576 dc ohmmeter 0 to 300 ohms, mid scales at 20 ohms 577 different type of engine bearing model 578 different type of piston model 579 drill point angle gauge 580 drill twist 1.5 mm to 15 mm ( various sizes ) by 0.5 mm 4 581 engineers stethoscope 582 glow plug tester 583 grover 3, 4, 6mm. 584 hammer mallet 585 hand vice 37 mm 586 high rate discharge tester ( cell tester ) 587 hydraulic jack hi lift type 3 ton capacity 588 pipe flaring tool 589 poker 590 portable oil monitoring indicator 591 radiator cut section down flow 592 rear axle assembly gear box steering box assembly of the diesel engine 593 ridger. 594 right cut snips 250mm 595 rivet sets snap and dolly combined 3mm, 4mm, 6mm 596 scraper flat 25 cm 597 shear tin mans 450 mm x 600mm 598 shovel 599 soldering copper hatchet type 500gms 600 solid parallels in pairs ( different size ) in metric 601 spirit level 2 v 250, 05 metre 602 spring tension tester 603 starter motor for tractor different type 604 stone, carborandum 15 x 5 x 4 cm smooth and rough. 605 straight edge gauge 4 ft. 606 thermostat 607 torque wrenches 5 35 nm, 12 68 nm & 50 225 608 wire gauge ( metric ) 609 gas welding table 1220mm x760mm 610 grinding machine ( general purpose ) d.e. pedestal with 300 mm dia wheels rough and smooth 611 p.t.o. operated rotary lawn mower 612 pipe bending machine ( hydraulic type ) 12mm to 30mm 613 trolley type portable air compressor single cylinder with 45 liters capacity air tank, 614 welding plant oxy acetylene complete ( high pressure ) 615 automatic transmission oils 616 center punch 10 mm. dia. x 100 mm. 617 electrician screw driver 250mm 618 hands file, second cut flat 20 cm. 619 screw driver 20cm.x 9mm. blade 620 screw driver 30 cm. x 9 mm. blade 621 steel tool box with lock and key ( folding type ) 400x200x150 mm 622 adjustable spanner pipe wrench 350 mm 623 air blow gun with standard accessories 624 air impact wrench with standard accessories 625 air ratchet with standard accessories 626 allen key set of 12 pieces 2mm to 14mm 627 ammeter dc with external shunt 300a / 60a 628 angle plate size 200x100x200mm 629 auto electrical test bench 630 blow lamp 1 litre 631 chisels cross cut 200 mm x 6mm 632 cleaning tray 45x30 cm. 633 compression testing gauge suitable for petrol engine. with standard accessories 634 copper bit soldering iron 0.25 kg 635 cylinder bore gauge 20 to 160 mm capacity 636 dial gauge type 1 gr. a ( complete with clamping devices and stand ) 637 drift punch copper 15 cm 638 electric soldering iron 230 v 60 watts 230 v 25 watts 639 electric testing screw driver 640 engineer’s square blade 15 cm. 641 feeler gauge 20 blades ( metric ) 642 file, square second cut 20 cm 643 file, square round 30 cm 644 file, triangular second cut 15 cm 645 granite surface plate with stand and cover 1600 x 1000mm 646 hacksaw frame adjustable 20 30 cm 647 hammer ball peen 0.75 kg 648 hammer chipping 0.25 kg 649 hammer copper 1 kg with handle 650 hammer plastic 651 hand operated crimping tool ( i ) for crimping up to 4mm and ( ii ) for crimping up to 10mm 652 hand reamers adjustable 10.5 to 11.25 mm, 11.25 to 12.75 mm, 12.75 to 14.25 mm and 14.25 to 15.75 mm 653 hand shear universal 250mm 654 hollow punch set of seven pieces 6mm to 15mm 655 insulated screw driver 20 cm x 9mm blade 656 insulated screw driver 30 cm x 9mm blade 657 left cut snips 250mm 658 magneto spanner set with 8 spanners 659 marking out table 90x60x90 cm. 660 multimeter digital 661 oil can 0.5 / 0.25 liter capacity 662 philips screw driver set of 5 pieces ( 100 mm to 300 mm ) 663 pipe cutting tool 664 piston ring groove cleaner. 665 prick punch 15 cm 666 scooter / motor cycle repairing stand 667 set of stock and dies unc, unf and metric 668 sheet metal gauge 669 shear tinnman’s 300mm 670 spanner clyburn 15 cm 671 spanners socket with speed handle, t bar, ratchet and universal up to 32 mm set of 28 pieces with box 672 straight edge gauge 2 673 stud remover with socket handle 674 surface gauge with dial test indicator plunger type i.e. 0.01 mm 675 tachometer ( counting type ) 676 taps and dies complete sets bsf 677 taps and wrenches metric 678 temperature gauge 0 100 deg c 679 thread pitch gauge metric, bsw 680 tyre pressure gauge with holding nipple 681 universal puller for removing pulleys, bearings 682 vacuum gauge 0 to 760 mm of hg 683 vice grip pliers 684 voltmeter 50v / dc 685 work bench with 4 vices 12cm jaw 250 x 120 x 60 cm 686 arbor press hand operated 2 ton capacity 687 automotive exhaust 5 gas analyzer ( petrol & diesel ) or diesel smoke meter 688 battery tester to test 12v / 24v 689 bench lever shears 250mm blade x 3mm capacity 690 cut section working model of continuous variable transmission 691 cut section working model of rotary clutch assembly of two wheeler 692 demonstration board of magneto ignition system of a two wheeler 693 discrete component trainer / basic electronics trainer 694 drilling machine bench to drill up to 12mm dia along with accessories 695 dual magnetization yoke ac / hwdc, 230 vac, 50hz 696 ignition coil and cdi unit of four different make 697 layout of working model 12 v automobile electrical systems 698 liquid penetrant inspection kit 699 motor cycle ( four stroke engine ) with digital twin spark 700 motor cycle ( two stroke engine ) 701 motor vehicle ( 3 wheeler ) 702 pneumatic rivet gun 703 ridge cutter 704 scooter ( four stroke engine ) 705 scooter ( two stroke engine ) 706 shock absorber for two wheeler four different type 707 three wheeler chassis frame & power transmission system. 708 three wheeler engine for dismantling and assembling 709 three wheeler steering system for dismantling and assembling 710 tin smiths bench folder 600 x 1.6mm 711 capacity air tank, along with accessories & with working 712 welding transformer 150 300 amps 713 working model of electronic ignition system of three wheeler 714 gloves for welding ( leather and asbestos ) 715 steel wire brush 50mmx150mm 716 computer chair 717 discussion table 8’ x 4’ x 2½ ‘ 718 lcd projector with led tv 42” 719 tool cabinet 6½ ‘ x 3’ x 1½’ 720 ac alternator slip ring puller variable 721 air blow gun with standard accessories trigger operated with interchangeable nozzles 722 auto electrical test bench for checking dynamo, alternator & starter. with minimum2hp ac motor, digital voltmeter & ammeter. 723 grease gun heavy duty trolley type 10 kg capacity 724 radiator cut section cross flow radiator with sectioned side tanks, radiator core. 725 starter motor axial type, pre engagement type & co axial type 726 turbocharger cut sectional view latest wgt type to show turbine, impeller and compressor wheels. 727 alternator assembly used for lmv alternator ( >50 amp ) 728 cut section models of shock absorbers 729 cut section of cross ply and radial tyres 730 demonstration board of mpfi system with injectors, rail, inlet manifold, throttle body, distributor, ecu, purge valve, sensor, crank pulley, fuel tank module. 731 functional / experiment model of different type of sensors. with different type of sensors like throttle position sensor, manifold absolute pressure sensor, engine coolant temperature sensor, vehicle speed sensor, oxygen sensor, crankshaft position sensor, camshaft position sensor, intake air temperature sensor, mass air flow sensor, knocksensor with ecu. 732 steering assembly – 1.rack & pinion 2.worm & roller 3. recirculating ball 4.power steering 5. electric assisted power steering 1. rack & pinion with steering wheel, column, tie rod end. 2. worm & roller steering assembly with drop arm. 3. recirculating ballsteering with pitman shaft and drop arm. 4. hydraulic working power steering with steering wheel, column, flow pipe, hydraulic pump, oil reservoir. 5. electric assisted power steering with rack and pinion, electric motor and motor control module 733 tandem master cylinder with booster working model 734 working model of torque converter model of lmv 735 diesel engine ( running condition ) stationary type single cylinder single cylinder, oh valves, fuel tank with handle, fuel feed, water cooling, oil pump. 736 multi scan tool to scan engine, abs & ebd, at, srs, body control and immobilizer should perform automotive sensor simulation test specially designed to diagnose and simulate vehicle sensor faults for sensors like map sensor, intake air temperature sensor, tp sensor etc. 737 heavy commercial vehicle fitted with latest 06 cylinder crdi diesel engine with all parts and accessories. ( without body on frame ) 738 tube / tyre vulcanizing machine 220 v , heater capacity 400w x 2 with different types of die &mould 739 tyre changer machine motorized pneumatic type, rim clamping facility, and bead breaking facilitywith air inflating device. 740 measuring steel tape 15meter 741 screw driver insulated 6mm x 150 mm 742 electrician screw driver thin stem insulated handle 4mm x 100 mm 743 heavy duty screw driver insulated 5mm x 200 mm 744 electrician screw driver thin stem insulated handle 4mm x 250 mm 745 knife double bladed electrician 100mm 746 electrician helmet yellow colour 747 gum boot standard quality 748 crimping tool 16 sq mm to 95 sq mm 749 digital multi meter dc 200mv 1000v, 0 – 10a & ac 200mv 750v , 0 10a, resistance 0 20 m` and 3 1 / 2 digit 750 a.c. voltmeter m.i. analog, portable box type housed in bakelite case multi range 75 v 150v 300v 600v 751 milli voltmeter centre zero analog, portable box type housed in bakelite case 100 – 0 – 100 mv 752 ammeter mc analog, portable box type housed in bakelite case 0 500 ma, 0 5 a, 0 25 a 753 ac ammeter mi, analog, portable box type housed in bakelite case 0 1 a, 0 5 a, 0 25 a 754 kilo wattmeter analog 0 1.5 3kw, pressure coil rating 240v / 440v, current rating 5a / 10a analog, portable type housed in bakelite case 755 digital wattmeter 230 v, 1 kw, 50 hz 756 a.c. energy meter single phase, 10 a, 240 v induction type ( as per iec 61850 ) 757 a.c. energy meter three phase, 15 a , 440 v induction type ( as per iec 61850 ) 758 digital energy meter single phase, three phase ( as per iec 61850 ) 759 mri equipment 760 power factor meter digital 440 v, 20 a, three phase portable box type 440 v, 20 a, three phase portable box type 761 frequency meter 45 to 55 hz 762 magnetic flux meter 0 500 tesla 763 lux meter lux meter lcd read out 0.05 to 7000 lumens with battery. 764 tachometer digital photo sensor type 10000 rpm 765 hydrometer 766 tong tester / clamp meter 0 100 a ( digital type ) 767 earth resistivity tester 768 wheat stone bridge with galvanometer and battery 769 single phase variable auto transformer 0 270 v, 10amp ( air cooled ) 770 ac starters: a. resistance type starter b. direct on line starter c. star delta starter manual d. star delta starter – semi automatic e. star delta starter – fully automatic f. star delta starter soft starter for a.c motors of 2 to 5 h.p. 771 synchroscope 440v, 50 hz 772 function generator 2 to 200 khz, sine, square, triangular 220 v, 50 hz, single phase 773 digital multi function meter 3 phase 774 soldering iron 120 watt, 775 temperature controlled soldering iron 50 watt, 230 volt 776 discrete component trainer discrete component ( for diode and transistor circuit ) with regulated power supply +5, 0 5 v, +12 , 0 12 v 777 linear i.c. trainer linear i.c. trainer with regulated power supply 1.2v to 15v pic socket 16pin and 20 pin with bread board 778 digital i.c. trainer digital i.c. trainer 7 segment display and bread board 779 oil testing kit oil testing kit 230 v, single phase 50 hz 60 va output 0 60 kv variable 780 ni cd battery 1.2 amps 781 dc power supply 0 30 v, 5 a 782 110 v battery charger 783 current transformer 415 v, 50hz, ct ratio 25 / 5 a, 5va 784 potential transformer 415 v, 50hz, pt ratio, 440v / 110v, 10va 785 d.c. milli ammeter 0 500m a 786 limit switch limit switch, liver operated 2a 500v, 2 contacts 787 relay a. cut out relays b. reverse current c. over current under voltage a. 16a, 440v b. 16a, 440v c. 16a, 440v d. 360v 440v 788 static relay distance protection 789 laboratory type induction coil 1000 w 790 knife switch dpdt fitted with fuse terminals 16 amp 791 earth plate 60cm x 60cm x 3.15mm copper plate 60cm x 60cm x 6mm gi plate 792 earth electrode primary electrode 2100x28x3.25mm secondary cu strip 20x5mm 793 elcb 2 pole, 32 amps, 240v 794 earth discharge rod 33kv 795 capacitors electrolytic, ceramic, polyester film, variable, dual run 796 various electronic components resistors, diode, transistor, ujt, fet, scr, diac, traic, igbt, small transformer etc. 797 bus bar with brackets 1 mtr each 798 lt fuse set ( henley unit ) 799 11 kv do fuse set 800 lt shackle insulator 801 bucholtz relay 802 breather with silica gel & oil 803 standard wire gauge 804 acsr conductor weasel, rabbit, raccoon, dog, panther, zebra, moose 1 meter piece 805 ht xlpe cable ( 1 meter piece ) 3x70, 3x120, 3x185, 3x240, 3x300 sq. mm 806 lt pvc insulated cable ( 1 meter piece ) 3½x 120, 3½x150, 3½x 240, 3½x 400, 3½x 600 sq mm 807 twisted pair cable, non metallic sheathed cable, underground feeder 1 mtr cable, ribbon cable, metallic sheathed cable, multi conductor cable, direct buried cable. 808 aerial bunched cable ( abc ) 70, 120, 185 sq mm 809 11kv pin insulator 810 11 kv pin with nut 811 11 kv disk insulator 812 11 kv suspension fitting 813 33 kv tension fitting 814 pcc pole clamp 815 pg clamp panther to panther, panther to dog & dog to dog 816 stone pad 817 cross arm v type 818 motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. shunt motor rating : 5 hp, 440v ac generator rating : 3 phase, 4 wire, 3.5 kva, 400 / 230 volts, 0.8 pf, 50 cycles 819 ac phase wound slip ring motor with starter switch 5 hp, 440 v, 3 phase, 50 hz 820 synchronous motor with accessories like starter, excitation arrangements. 3 phase, 3 hp, 440v, 50hz, 4 pole 821 thyristor / igbt controlled a.c. motor drive with vvvf control 3 phase, 2 hp 822 single phase transformer, core type, air cooled kva , 240 / 415 v, 50 hz 823 three phase transformer, shell type oil cooled with delta / star 3 kva , 415 / 240 v, 50 hz 824 secondary injection set 825 fire extinguisher foam type, & dry power type 826 rule steel 300 mm both in inch and mm 827 hacksaw frame adjustable 250 to 300 mm 828 scriber 200 mm 829 chisel cold, flat 20 mm 830 hammer ball pein 800 grams 831 level spirit wooden 300 mm 832 trowel c 125 i s: 6013 833 screw driver 250 mm 834 cutting pliers 200mm i s : 3650 835 marking table 900x600x900mm high 836 file flat rasp 250 mm 837 brush steel wire 150x 50 mm 838 washer cutter 839 soil pot with brush 840 d. e. spanners 7x8, 10x11, 13x17, 19x22, 24x27 is:2028 841 bending spring 842 tool caulking set of s 843 pipe vice to grip up to 77 mm is 2587 844 chain :pipe wrench 90mm 650 is 4123 845 adjustable, spanner, a 375, is 6149 846 leg vice, 75mm jaw on stand is 2588 847 drill twist ( straight shank ) 3mm to 6mm 848 portable forge , 450mmwith hand blower 849 d.e. pedestal grinder with two wheels 175mm rough and smooth 850 hydraulic pressure machine for testing leakage in gi pipe fittings etc. 851 sight rail and bonning rod 852 dormat, pickaxe, spade, girmale 853 solar water heater system 854 ring guage 15 mm, 20mm, 25mm, 32mm 855 rule steel 24 856 brush round short hair ( consumable ) 0 to 12 no. 857 brush flat short hair ( consumable ) 0 to 12 no. 858 varnish brush soft hair ( consumable ) 25mm, 50mm, 75mm, 100mm 859 colour pallet for water colour ( consumable ) big size 860 t square imperial size 861 easel a type stand 862 square blade150mm 863 marking gauge 864 hand saw 450 mm 865 tendon saw 300mm 866 jack plane 867 mallet round 868 hammer ( crass pin ) 869 drill bits ( consumable ) 3 mm, 5mm, 8mm, 10mm, 12mm 870 chisel knife 5mm, 8mm, 10mm, 20mm, 30mm 871 hacking knife 872 palate knife set 873 diamond glazier knife 874 paint tin opener 875 scraper knife 876 shave huck knife 877 glider knife 878 paint burner ( acetylene gas ) 879 step ladder ( aluminum ) 6 feet 880 scaffolding ( movable ) h 2000mm x w 1400mm x l 2000mm. 881 weight per litter cup 100 ml capacity 882 ford cop for viscosity measurement with stand no.3 & no.4 883 mild steel panels 300 mm x 200 mm ( 18 x 22 swg ) 884 sink ( stainless steel ) h 250mm x w 450mm x l 600mm. 885 suction feed spray gun with accessories 1 ltr. capacity of cup 886 glosso meter 887 infra red lamp 888 digital dft meter 889 aerograph ( air brush / pen gun ) 890 pneumatic polishing machine with pads 891 gloves ( rubber ) ( consumable ) 892 pipe wranch 10& 16 893 flat file smooth finish 12 894 circuler cut file 12 895 raft cut 12 896 pipe dai set metric & inches find peach 897 gun spray with gravity feed cup with complete accessories with complete accessories ( capacity ¼ ltr. , 1 / 2 ltr. , 1 / 3ltr. , 1 ltr. ) 898 conventional spray gun for pressure feed with complete accessories 899 electric spray gun with complete accessories 900 comb gauge 901 pencil hardness tester 902 digital weight machine capacity 5 kg. weighing scale 903 air compressor 3 phase, 2 hp 904 air compressor single phase, 1 hp 905 pressure feed container with conventional 20 ltr. capacity with complete accessories 906 electrostatic spray gun unit with complete accessories 907 airless spray gun unit with complete accessories 908 side draught dry paint booth overall dimensions ( mm ) : 1580 ( w ) x 2250 ( d ) x 3200 ( h ) ; working dimensions ( mm ) : 1500 ( w ) x 1320 ( d ) x 2040 ( h ) 909 power coating set up with gun booth & oven 910 software card draw / page make / photo shop / shree lippi / ism / acee dcee viewer ( latest version ) 911 radium plotter and cutter with stand complete accessories 48 912 file flat rough double cut 200mm 913 file, half round, fine double cut, length 150mm 914 file, round, fine double cut length 150mm 915 file flat, fine double cutlength 150mm 916 file square, fine double cut, length 150mm 917 file triangular fine double cut length 150mm 918 caliper, odd leg, spring joint length 150mm 919 cold chisel flat and cross cut length 150mm 920 engineers rule 300mm long 921 tape measuring 10m graduation in mm 922 pliers combination insulated length 200mm 923 pliers long nose 200 mm 924 line tester 500 v heavy duty 925 bench vice 150 to 300mm jaw 926 hack saw tubular metal frame adjustable 300mm 927 snip sheet metal straight nose 200 mm 928 anvil 100x200mm 929 soldering iron exchangeable copper tip 65 watts 930 knife folded stainless steel 150mm 931 tong tester ( clamp on multi meter ) 0 10 30 amps 0 500 v 932 firmer chisel 6, 12, 25mm 933 fire buckets 10 litre with stand 934 quick couples, process tube adopter 935 welding table for gas / arc 1200x760 936 flaring tool set, single type for tube. 4.7mm to 16mm o.d 937 swaging tool, punch type, set of size for tube. 4.7mm to 16mm o.d 938 pipe cutter miniature for copper tube 3mm to 16mm dia 939 pinch of tool, for copper tube, 6mm to 18mm dia 940 ratchet spanner 6.4 sq.mm reversible 941 spanner double ended 4.7mm to 16mm 942 ring spanner off set 4.7mm to 16mm 943 wrench adjustable length 150mm 944 valve key handle [ treated as consumable ] 4.7mm & 6.4mm sq. 945 ( hollo ) punch hole for cutting gasket 4.7 16mm die 946 scissor, gasket cutting stainless steel length 25mm 947 t allen key set size 5 / 32 to 1 / 8 948 pipe cutter with built in reamer and space cutter, for copper tube 3mm to 32mm 949 pipe / tube bender lever type 3 16 mm 950 spanner double ended 19mm to 31.8 mm 951 pipe wrench size 50mm to 150mm 952 lapping plate 250mm x 200mm 953 hammer ball peen 450 gms 954 puller 3 legged with flexible arm 300mm 955 spirit level precision metallic 200mm 956 tap set with matching drills 3 mm to 16mm 957 tap set with matching drills v to 5 / 8 958 torque wrench 300mm 12.7mm 959 piercing valve ¼ inch 960 feeler gauge 0.05mm to 1mm 961 four way reversible valve 962 vernier hight gauge 300mm , lc 0.02 963 service oscillator 964 a.f.o oscillators 965 gas leak detector for halogengas 966 sling psychro meter mounted on aluminum back, scale 100 c to +1100 c 967 vernier caliper length 250mm 968 tachometer digital, multi range 0 r m p to 3000 r m p. portable small size in leather case 969 fin straightened / fin comb. with strong steel wire based combing on wood 970 split phase induction motor 1hp, 230 v 971 bldc motor with controller 15 – 30 watts, 315 volt dc 972 idu pulse generation type motor 15watt, 230volt a.c 973 star delta starter 2 hp 974 single door direct cool refrigerator, carrying with hfc and hc 185 l 975 frost free refrigerator 200l carrying with hc blend 976 three / four door refrigerator ( inverter type ) 300l carrying with hc r 600a 977 core drill machine. 978 grinding machine 200mm, 3000rpm, double ended1 / 2hp 979 window a.c 1 ton with r 22 blend reciprocating compressor 980 split a.c 1.5 ton with r134a or r 22 reciprocating compressor 981 duct able split a.c 1.5 ton 1.5 ton with r134a or r 22 reciprocating compressor 982 recovery unit with cylinders cfc, hfc&hcfc 983 decibel meter 30 100 db 984 cassette air conditioner 4500 kcal / hr 985 fan coil unit with water valves ( 2 & 3 way ) 986 refrigerant cylinder 10 kg capacity 987 gauge manifold with gauges 988 deep freezer 200 l carrying with hfc 134a& reciprocating compressor 989 display cabinet 2 ton capacity 990 water cooler storage type 200 l carrying with hfc 134a& reciprocating compressor 991 water dispenser bubble type ( hot and cold ) 2.5 to 3ltr. delivery capacity per hour 992 ice candy plant 2 ton with capacity to make 32 ice candy at a time with forma tray, stainless steel tank on trolley 993 air conditioning, direct system. complete with all controls including humidity control 994 air conditioning, indirect system. ( water cooled ) complete with all controls including humidity control 995 package a / c 5 ton capacity, air cooled type with open type compressor reciprocating type 996 bus ac tutorial model 997 automatic ice cube m / c 50 kg / hour 998 storage type water cooler ( hot and cold ) 999 vrf / vrv unit with two indoor units 2.5tr each and 5tr capacity out door unit complete with air cooled condenser, accessories and controls. 1000 split a / c ( inverter technology ) 1.5 tr 1001 walk in cooler puf insulated for cold room 6x4.5x8 cft. temperature 00 50 c 1002 absorption system small size 1003 class room table one table for each trainee size of 2.5 provisions with open rack. frame square conduit of1.top sun mica ply board 1004 work bench 2000 x1000 x 700 mm with 2 pipe frame. top with teak slab and fixing with3 / 4 good quality rubber sheet. 1005 lockers 195 x 90 x 48 cm set six locker in one structure 1006 glass board portable 2.5x4 with stand 1007 instructor table 4x2x2.5 with steel tubular frame & sun mica top 1008 instructor chair standard revolving with wheel 1009 computer chair revolving type metal based & metal wheel standard one 1010 chart stand 6x3 providing with hanging clip top & bottom plate 1011 computer with printer and scanner latest configuration 1012 copier machine. 1013 interactive board latest version 1014 book self with glass panel 6’ x 3’ 1015 caliper outside spring joint 150 mm 1016 caliper inside spring joint 150 mm 1017 caliper odd leg firm joint 150 mm 1018 steel rule 150 mm, graduated both in metric and english unit 1019 scriber 150 mm x 3 mm 1020 hammer ball peen 250 gm with handle 1021 prick punch 100 mm 1022 surface plate granite 1000 x 1000 mm with stand andcover 1023 bench vice 125 mm jaw 1024 v block 150x100x100 mm with clamp ( hardened & ground ) 1025 universal surface gauge 250 mm arm 1026 hammer ball peen 750 gm with handle 1027 hammer copper / brass 500 gm with handle 1028 hacksaw fixed 200 mm ( pistol grip ) 1029 file flat 300 mm rough 1030 file flat 250 mm 2nd cut 1031 file half round 250 mm 2nd cut 1032 file round 250 mm smooth 1033 file half round 150 mm smooth 1034 knurling tool revolving head ( rough, med, fine ) diamond and straight 1035 combination set 300 mm ( complete set ) 1036 screw driver 10 x 200 mm 1037 spanner double ended 6 mm to 21 mm 1038 spanner adjustable 200 mm 1039 pliers flat nose 150 mm side cutting 1040 caliper transfer inside 150 mm 1041 micrometer outside 0 to 25 mm, least count 0.01 mm with nabl accredated lab.certificate 1042 micrometer inside up to 25 mm, least count 0.01 mm with nabl accredated lab.certificate 1043 micrometer inside up to 25 to 50 mm, least count 0.01 mm with nabl accredated lab. certificate 1044 depth gauge micrometer 0 to 150 mm, least count 0.01 mm with nabl accredated lab. certificate 1045 vernier caliper outside, inside and depth200 mm / 8 inches with metric & inch scale ( l.c. = 0.02mm ) with nabl accredated lab. certificate 1046 dial vernier caliper with metric 200 mm, least count 0.05 mm with nabl accredated lab. certificate 1047 vernier bevel protractor 300 mm blade with nabl accredated lab. certificate 1048 vernier micrometer 0 25 mm o / s lc 0.001mm with nabl accredated lab. certificate 1049 vernier micrometer 25 50 mm, outside least count 0.001mm with nabl accredated lab. certificate 1050 vernier micrometer 0 inch to 1 inch.outside least count 0.001 inch with nabl accredated lab. certificate 1051 gauge radius set 1 mm to 25 mm by 0.5 mm 1052 centre gauge com. 60°, 55° and 29° 1053 screw pitch gauge whitworth ( 0.25 to 6mm ) 1054 drill angle gauge 1055 vernier height gauge 0 300 mm, lc = 0.02 mm with nabl accredated lab. certificate 1056 plain ring and plug gauge ( 12, 16, 20, 25, 30, 32, 36, 40, 45, 50 mm ) 1057 wheel dresser huntingon type with star cutter 1058 wheel dresser diamond ( inserted 0.75 or 1 carat ) 1059 morse taper plug & ring gauge no. 0 to 7 mt 1060 sine bar with centers 200 mm 1061 slip gauge metric set ( 87 pieces in a box ) with workshop grade 1062 morse taper sleeves no. 0 1, 1 2, 2 3, 3 4, 4 5. 1063 drill drift 1064 twist drill straight shank 3 to 12 mm by 1 mm 1065 drill twist set taper shank 14 mm to 20 mm by 1 mm 1066 drill chuck 12 mm cap with key 1067 tap & die b.a. no. 0 to 10 in a box 1068 tap and die set metric 3 to 24 mm 1069 tap & die b.s.f. up to 1 inch 1070 tap & die b.s.w. up to 1 inch 1071 reamer machine straight flute 6 to 25 mm 1072 reamer adjustable 10 to 20 mm 1073 tool holder rh & straight for mm square tool 1074 parting tool holder with h.s.s. blade 1075 tool bits 12 x 150 mm sq. assorted shaped 1076 boring tool holder 6 mm sq. tool bit 1077 oil can ½ pint ( pressure feed system ) 1078 angle plate adjustable 150 x 175 x 250 mm 1079 spirit level 0.05 mm / 200 mm 1080 tool maker’s button 1081 combination drill / centre drill a3, a4 & a5 1082 tap wrench ( adjustable ) 1083 die handle 1084 tool bit assorted sizes on holder 1085 spare grinding wheel ajax type for carbide tool 1086 almirah 1980x 910 x 480 mm 1087 stool revolving 1088 angle gauge for tool grinding 1089 hand chaser m 12 & m 16 ( external ) 1090 hand chaser m 12 & m 16 ( internal ) 1091 revolving center ( to suit lathe tailstock ) 1092 tool cemented carbide assorted shaped ( external ) for steel turning 1093 thread plug gauge m 20 & m 21 1094 thread ring gauge m 20 & m 21 1095 machine chaser m 12 to m 21 ( std. series ) to suit on 1096 coventry die head 1097 gauge drill grinding 1098 magnetic chuck 150 mm dia. ( circular type ) 1099 lathe mandrels ( diff. types ) 1100 coventry type die head ( self opening ) 1101 collapsible tap with attachment 1102 bore dial gauge stems 12 to 35 mm, 35 to 65 mm., dial gauge indicator of 0.01 accuracy. 1103 lathe s.s. & s.c. ( all geared head stock ) with minimum specification as: 750 mm between centers. machine to be motorized and supplied with coolant installation, 4 jaw independent chuck 150 mm, 3 jaw self centering chuck 150 mm, fixed steady, traveling steady, face plate, driving plate, 4 way tool post, quick change gear box for metric or british threads, live and dead centers with taper attachments, motor capacity 5.5 kw 1104 lathe s.s & s.c. ( all geared type ) with minimum specification as: 150 mm center height, 1000 mm between centers. machine to be motorized and supplied with coolant installation, 4 jaw independent chuck 250 mm, 3 jaw self centering chuck 150 mm fixed steady, traveling steady, face plate, driving plate, 1 way tool post, draw in type collets set up to 25 mm, 0.5 mm, relieving attachments, motor capacity 5.5kw 1105 grinding machine pedestal type d.e. 200 mm dia. wheel with wheel guard and vision, motor capacity 0.75 kw 1106 drill machine pillar type motorized up to 12 mm. cap, motor capacity 0.75 kw 1107 power saw machine – hydraulic feed system 400 mm. blade size, motor capacity 0.75 kw 1108 ( b ) desktop computers 1109 tool holders 1110 digimatic electronic vernier caliper inch and mm 8 / 200 mm. lcm 0.005 / 0.001 mm 1111 digimatic electronic outside micrometer ( 0 to 25 mm & 25 to 50 mm ) lc 0.001 mm. 1112 welding hand shield fiber 1113 chipping hammer with metal handle 250 grams 1114 chisel cold flat 19 mm x 150 mm 1115 centre punch 9 mm x 127 mm 1116 stainless steel rule 300mm 1117 scriber 150 mm double point 1118 flat tongs 350mm long 1119 hack saw frame fixed 300 mm 1120 file half round bastard 300 mm 1121 file flat 350 mm bastard 1122 hammer ball pane1 kg with handle 1123 tip cleaner 1124 try square 6” 1125 letter punch 6 mm 1126 magnifying glass 100 mm dia. 1127 universal weld measuring gauge 1128 earth clamp 600a 1129 spanner d.e. 6 mm to 32mm 1130 c clamps 10 cm and 15 cm 1131 hammer sledge double faced 4 kg 1132 electrode holder 600 amps 1133 h.p. welding torch with 5 nozzles 1134 oxygen gas pressure regulator double stage 1135 acetylene gas pressure regulator double stage 1136 co2 gas pressure regulator with flow meter 1137 argon gas pressure regulatorwith flow meter 1138 metal rack 182 cm x 152 cm x 45 cm 1139 flash back arrester ( torch mounted ) 1140 flash back arrester ( cylinder mounted ) 1141 welding transformer with all accessories ( 400a, ocv 60–100 v, 60% duty cycle ) 1142 welding transformer ( or ) inverter based welding machine with all accessories ( 300a, ocv 60 – 100 v, 60% duty cycle ) 1143 d.c arc welding rectifiers set with all accessories ( 400 a. ocv 60 – 100 v, 60% duty cycle ) 1144 gmaw welding machine 400a capacity with air cooled torch, regulator, gas pre heater, gas hose and standard accessories 1145 ac / dc gtaw welding machine with water cooled torch 300 a, argon regulator, gas hose, water circulating system and standard ccessories. 1146 air plasma cutting equipment with all accessories, capacity to cut 12 mm clear cut 1147 air compressor suitable for above air plasma cutting system. 1148 auto darkening welding helmet 1149 spot welding machine 15 kva with all accessories 1150 portable gas cutting machine capable of cutting straight &circular with all accessories 1151 pedestal grinder fitted with coarse and medium grain size grinding wheels 300 mm dia. 1152 bench grinder fitted with fine grain size silicon carbide green grinding wheel 150 mm dia. 1153 ag 4 grinder 1154 suitable gas welding table with fire bricks 1155 suitable arc welding table with positioner 1156 hand shearing machine capacity cut 6 mm sheets and flats 1157 power saw machine14’’ 1158 portable drilling machine ( cap. 6 mm ) 1159 oven, electrode drying 0 to 350°c, 10 kg capacity 1160 work bench 340x120x75 cm with 4 bench vices of 150 mm jaw opening 1161 oxy acetylene gas cutting blow pipe 1162 oxygen, acetylene cylinders ** 1163 co2 cylinder ** 1164 argon gas cylinder ** 1165 anvil 12 sq. inches working area with stand 1166 swage block 1167 die penetrant testing kit 1168 magnetic particle testing kit # 1169 portable abrasive cut off machine 1170 suitable gas cutting table 1171 welding simulators for smaw / gtaw / gmaw 1172 safety boots for welders 1173 arc welding cables multi cored copper 400 / 600 amp as per bis 1174 arc welding single coloured glasses 108 mm x 82 mm x 3 mm. din 11a &12 a 1175 arc welding plain glass 108 mm x 82 mm x 3 mm. 1176 gas welding goggleswith colour glass 3 or 4a din 1177 spark lighter 1178 ag 4 grinding wheels 1179 instructors lap top with latest configuration preloaded with operating system and ms office package. 1180 welding process, inspection & codes dvd / cds 1181 table for trainees 1182 cupboard ( big ) 1183 white board size: 8ft. x 4ft. 1184 computer ( pc ) with latest configurations and internet connection with standard operating system and standard word processor and worksheet software 1185 lead acid battery 75ah 12v 1186 transformer single phase 1 k.v.a. 250 / 100v 1187 transformer three phase ( oil cooled ) 5 k.v.a. 440 / 220 v 1188 autotransformer single phase 0 300v 1kva 1189 autotransformer three phase 0 500v 1kva 1190 current transformer 10 / 1, 20 / 1, 30 / 1, 50 / 5, 100 / and 300 / 5a 1191 potential transformer 220 / 110, 300 / 110, 440 / 110, 600 / 110 1192 earth leakage circuit breaker ( elcb ) 220v / 25ma 1193 metal clad circuit breaker ( mccb ) 220v / 1a...

Military Engineer Services - Uttar Pradesh

20096929 tender for maintenance of e / m installation=> 106.00 m&l cement concrete type b1, 1:2:4 using 20mm graded aggregate in lintels upto 1.5m clear span, cills, seismic and other similar bands, copings, bond stones, bed plates for hold fast , benching, suacer drain and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete allas specified 107.00 s&f of mild steel work such as framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, , riveting, etc.. n exc 10 kg each brackets, conforming to fe.290.gde e 165 complete all as spd 108.00 s&f of mild steel work such as bands, straps, supports or stays for rainwater including bolts, if required: hooks ( stay ) , heavy, for large gates; hook and pintle hinges: large hasps and staples; ; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; , plate washers and similar small articles conforming to fe 290 gde e 165 complete all as spd 109.00 extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement incl form, moulds metered / stopped ends etc complete all as spd and as directed by engr in charge 110.00 m&l for sand filling in floor or paving laid a layer of n exe 15cm thich spread, levelled and rammed including watering complete all as spd 111.00 m&l broken stone aggregate 40 to 80mm graded including spreading , levelling etc in the ht switch yard / sub station yard complete all as spd 112.00 m&l for 50micron polythene sheet laid below sand / broken aggregate complete all as spd 113.00 m&l in repair sythetic insulation mat of size 2mx 1mx19mm complete all as spd 114.00 s & f in repairs 20 mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. 115.00 taking down shutters of any description exc 1.0 sqm each....

Military Engineer Services - Uttar Pradesh

20096928 tender for maintenance of e / m installation=> 99.00 m&l for 40mm plain cement concrete type b 1, 1:2:4 ( 20mm graded aggregate ) as in floor and finished even and smooth without using extra cement with pannels by using 4mm glass dividing strips of 38mm width complete all as spd and directed by eic ( 3mm thick glass dividing strips will be measured and paid seperate item ) 100.00 m&l for pcc 1:3:6 type c 1 using 20mm graded stone aggregate as in plinth protection and path laid in alternate panels not more than 3 mtr in length, laid to slope 1:30 including forming joints 10 mm wide and upto full depth of pcc and filled with bitumen mastic ( 1:3 ) 1 part bitumen 85 / 25 and 3 parts of sand complete all as specified and directed. { note: rate is deemed to be inclusive of materials against forming & filling of joints } 101.00 excavating in trenches, n exc 1.5 m wide for foundation exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard / dense soil complete all as spd 102.00 returning, filling in, including spreading, levelling, wateringand well ramming in layers not exc 25 cm in hard / dense soil complete all as spd 103.00 removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as spd 104.00 m&l hardcore ( broken stone ) of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled / rammed to a true surface complete all as spd 105.00 m&l cement concrete in foundations, filling and mass concrete, type d2 1:4:8 ( 40 mm graded aggregate ) complete all as spd 106.00 m&l cement concrete type b1, 1:2:4 using 20mm graded aggregate in lintels upto 1.5m clear span, cills, seismic and other similar bands, copings, bond stones, bed plates for hold fast , benching, suacer drain and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete allas specified 107.00 s&f of mild steel work such as fra...

Military Engineer Services - Uttar Pradesh

20096914 tender for maintenance of e / m installation=> 37.00 s & f 75 mm bore pvc ( swr ) bends of any radius complete all as specified and directed. 38.00 s & f 110 mm bore pvc ( swr ) junction single ( single `t ) equal or unequal. 39.00 s & f 75 mm bore pvc ( swr ) junction single ( single `t ) equal or unequal. 40.00 s & f pvc floor trap of 75 mm outlet with grating including jointing to waste pipe in run lead. 41.00 plain cement concrete type c1 ( 1:2:4 ) ( using 20 mm graded stone aggregate ) cast in situ in lintels up to 1.5 m span, cills and other similar bands, plinth courses, parapets, copings, bed plates, hold fast and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work. 42.00 taking down chowkats or frames exceeding 1.5 sq. m but not exceeding 4 sq. m each ( without taking off shutters from the frame ) 43.00 taking down chowkats or frames not exceeding 1.5 sq. m each ( without taking off shutters from the frame ) 44.00 taking down shutters of any description exc 1.0 sqm but not exceeding 2.00 sq. m each. 45.00 s & f mild steel angles, bars, flats etc., as in supports for stiffening of fencing, wall ties, hold fasts, clamps, plain angle cleats for securing purlins and similar small articles confirming to fe 290. gdee 165 46.00 s & f 35 mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., ( without sash bars ) , edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. 47.00 s&f 35 mm thick factory made flush shutters solid core construction with block board core and plywood face panels, commercial type on both side complete all as specified and directed....

Directorate of Training and Employment - Uttar Pradesh

19170929 purchase tool and equipment : 129 motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. shunt motor rating : 5 hp, 440v ac generator rating : 3 phase, 4 wire, 3.5 kva, 400 / 230 volts, 0.8 pf, 50cycles 130 ac phase wound slip ring motor with starter and switch 5 hp, 400 volts, 3 phase, 50 cycles 131 single phase capacitor motor with starter switch 1 hp 230 volt 50 cycles 132 universal motor with starter / switch 230 volt, 50 cycles ¼ hp 133 stepper motor with digital controller 134 shaded pole motor 135 synchronous motor 3 phase, 3 hp, 415v, 50hz, 4 pole, with accessories. 136 lux meter 137 domestic appliances – mixture & grinder 138 thyristor / igbt controlled d.c. motor drive with tachogenerator feedback arrangement 1 hp 139 thyristor / igbt controlled a.c. motor drive with variable voltage variable frequency drive control 3 phase, 2 hp 140 pentium iv computer or latest ( server linux ) , 2.8 ghz & above, ͳ gb ram, ͺͳ gb hdd, dvd combo drive, ͳ5 / ͳͳdz monitor, optical scroll mouse, multimedia key board, 32 bit lan card with upp port, necessary drivers, etc. 141 ink jet / laser printer 142 washing machine 143 motor pump set 1 hp, 1 phase, 240 v 144 pin type, shackle type & suspension type insulators ( raw material ) 145 pentium iv computer or latest ( server linux ) , 2.8 ghz & above, ͳ gb ram, ͺͳ gb hdd, dvd combo drive, ͳ5 / ͳͳdz monitor, optical scroll mouse, multimedia key board, 32 bit lan card with upp port, necessary drivers, etc. 146 machinist...

Directorate of Training and Employment - Uttar Pradesh

18908448 supply of tools and equipments 4 motor generator(dc to ac) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. shunt motor rating : 5 hp, 440v ac generator rating : 3 phase, 4 wire, 3.5 kva, 400/230 volts, 0.8 pf, 50cycles 5 ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse. 2 to 3 hp, 3 phase ,400 volts, 50 cycles 6 ac phase wound slip ring motor with starter and switch 5 hp, 400 volts, 3 phase, 50 cycles 7 a.c. series type motor with mechanical load ¼ hp, 230v, 50 hz 8 single phase capacitor motor with starter switch 1 hp 230 volt 50 cycles 9 universal motor with starter/switch 230 volt, 50 cycles ¼ hp 10 stepper motor with digital controller make any repuated/isi/iso certified co 11 shaded pole motor make any repuated/isi/iso certified co 12 bath impregnating make any repuated/isi/iso certified co 13 oven stove sl. no. name of the items 1 synchronous motor 3 phase, 3 hp, 415v, 50hz, 4 pole, with accessories. 2 lux meter make any repuated/isi/iso certified co sl. no. name of the items 1 inverter 1 kva with 12 v battery c. electric iron 1500 watts make any repuated/isi/iso certified co d. immersion heater 1500 watt make any repuated/isi/iso certified co e. a.c. fan 1200mm polar/khaitan/usha f. geyser (storage type) 15 ltr minimum g. mixture & grinder 3 thyristor /igbt controlled d.c. motor drive with tachogenerator feedback arrangement 1 hp 4 thyristor/igbt controlled a.c. motor drive with variable voltage variable frequency drive control 3 phase, 2 hp pentium iv computer 2 ink jet printer / laser printer ...

Directorate of Training and Employment - Uttar Pradesh

18639277 purchase tool and equipment : 125 discrete component trainer item 124 1.00 nos 126 linear i.c. trainer item 125 1.00 nos 127 digital i.c. trainer item 126 1.00 nos 128 oil testing kit item 127 1.00 nos 129 a. cut out relays b. reverse current c. over current d. under voltage item 128 1.00 set 130 starters for 2 to 5 h.p. a.c motors a. resistance type starter b. direct on line starter c. star delta starter manual, semi automatic and automatic d. auto transforme type item 129 1.00 set 131 motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. shunt motor rating : 5 hp, 440v ac generator rating : 3 phase, 4 wire, 3.5 kva, 400 / 230 volts, 0.8 pf, 50cycles item 130 1.00 set 132 ac phase wound slip ring motor with starter and switch 5 hp, 400 volts, 3 phase, 50 cycles item 131 1.00 nos 133 single phase capacitor motor with starter switch 1 hp 230 volt 50 cycles...

Directorate of Training and Employment - Uttar Pradesh

18639265 purchase tool and equipment : 119 motor generator ( ac to dc ) consisting of : squirrel cage induction motor with star delta starter and directly coupled to dc shunt generator and switch board mounted with regulator, air breaker, ammeter, voltmeter, knife blade switches and fuses, set complete with case iron and plate, fixing bolts, foundation bolts and flexible coupling. item 118 1.00 set 120 used dc generators series, shunt and compound type for overhauling practice item 119 1.00 set 121 diesel generator set with change over switch, over current breaker and water cooled with armature, star delta connections ac 3 phase, 5 kva, 240 volt item 120 1.00 nos 122 three phase transformer, shell type oil cooled with all mounting 3 kva , 415 / 240 v, 50 hz , item 121 1.00 nos 123 oscilloscope dual trace, 30 mhz item 122 1.00 nos 124 function generator 125 discrete component trainer item 124 1.00 nos 126 linear i.c. trainer item 125 1.00 nos 127 digital i.c. trainer item 126 1.00 nos 128 oil testing kit item 127 1.00 nos 129 a. cut out relays b. reverse current c. over current d. under voltage item 128 1.00 set 130 starters for 2 to 5 h.p. a.c motors a. resistance type starter b. direct on line starter c. star delta starter manual, semi automatic and automatic d. auto transforme type item 129 1.00 set 131 motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. shunt motor rating : 5 hp, 440v ac generator rating : 3 phase, 4 wire, 3.5 kva, 400 / 230 volts, 0.8 pf, 50cycles item 130 1.00 set 132 ac phase wound slip ring motor with starter and switch 5 hp, 400 volts, 3 phase, 50 cycles item 131 1.00 nos...

Directorate of Training and Employment - Uttar Pradesh

18621983 purchase tool and equipment : 121 diesel generator set with change over switch, over current breaker and water cooled with armature, star delta connections ac 3 phase, 5 kva, 240 volt 122 three phase transformer, shell type oil cooled with all mounting 3 kva , 415 / 240 v, 50 hz , 123 oscilloscope dual trace, 30 mhz 124 function generator125 discrete component trainer 126 linear i.c. trainer 127 digital i.c. trainer 128 oil testing kit 129 a. cut out relays b. reverse current c. over current d. under voltage 130 starters for 2 to 5 h.p. a.c motors a. resistance type starter b. direct on line starter c. star delta starter manual, semi automatic and automatic d. auto transforme type 131 motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. shunt motor rating : 5 hp, 440v ac generator rating : 3 phase, 4 wire, 3.5 kva, 400 / 230 volts, 0.8 pf, 50cycles 132 ac phase wound slip ring motor with starter and switch 5 hp, 400 volts, 3 phase, 50 cycles 133 single phase capacitor motor with starter switch 1 hp 230 volt 50 cycles...

Department Of Training - Uttar Pradesh

18047305 tender for purchase of tools and equipments 2027 dc compound motor with starter and switch 2 to 2.5 kw ,220 volts 2028 single phase transformer, core type, air cooled 1 kva , 240/415 v, 50 hz 2029 three phase transformer, shell type oil cooled with all mounting 3 kva , 415/240 v, 50 hz , (delta/star) 2030 oscilloscope dual trace, 30 mhz 2031 function generator 2032 discrete component trainer 2033 linear i.c. trainer 2034 digital i.c. trainer 2035 oil testing kit 2036 hygrometer 2037 a. cut out relays b. reverse current c. over current d. under voltage 2038 starters for 2 to 5 h.p. a.c motors a. resistance type starter b. direct on line starter c. star delta starter manual, semi automatic and automatic d. auto transformer type 2039 motor generator(dc to ac) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. shunt motor rating : 5 hp, 440v ac generator rating : 3 phase, 4 wire, 3.5 kva, 400/230 volts, 0.8 pf, 50cycles 2040 ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse. 2 to 3 hp, 3 phase ,400 volts, 50 cycles 2041 ac phase wound slip ring motor with starter and switch 5 hp, 400 volts, 3 phase, 50 cycles 2042 a.c. series type motor with mechanical load ¼ hp, 230v, 50 hz 2043 single phase capacitor motor with starter switch 1 hp 230 volt 50 cycles 2044 universal motor with starter/switch 230 volt, 50 cycles ¼ hp 2045 stepper motor with digital controller 2046 shaded pole motor 2047 bath impregnating 2048 oven stove 2049 synchronous motor 3 phase, 3 hp, 415v, 50hz, 4 pole, with accessories. 2050 lux meter 2051 inverter 1 kva with 12 v battery input 12 volt dc, output 220 volt ac ...

Ministry Of Railways - Uttar Pradesh

14265949 tender for erection of open web through girders of br no 108 & 109 including lowering of existing bridge girders between lko cnb, assembling & erection of plate girder of br. no 796 a including lowering of existing bridge girders at lucknow yard, assembling & launching of girder of r.o.b at lc no. 27, replacing of bed plates of existing bridge girder at br no 441 including miscellaneous repair of bridges over lucknow division."...

Northern Railway - Uttar Pradesh

14264545 tender for assembling & erection of open web through girders of br no 108 & 109 including lowering of existing bridge girders between lko cnb, assembling & erection of plate girder of br. no 796 a including lowering of existing bridge girders at lucknow yard, assembling & launching of girder of r.o.b at lc no. 27, replacing of bed plates of existing bridge girder at br no 441 including miscellaneous repair of bridges over lucknow division...

Research Designs And Standards Organisation - Uttar Pradesh

3108452 supply installation and commissioning of bed plate of size 4000mm length x2500mm width x350 mm thickness in finish machined condition with t slots of 36h 12 confirm to is:10602 1983 along with foundation bolt and accessories unit weight 10 tone...

Research Designs And Standards Organisation - Uttar Pradesh

3030053 supply installation and commissioning of bed plate of size 4000 mm length x 2500 mm width x 350 mm thickness in finish machined condition with t slots of 36 h12 confirm to is: 10602 1983 along with foundation bolt and accessories unit weight 10 tone approximate as per attached drawing and specification....

Research Designs And Standards Organisation - Uttar Pradesh

2612242 supply, installation & commissioning of bed plate of size 4000 mm length x 2500 mm widh x350 mm thickness in finish machined condition with t slots of 36 h12 confirm to is:10602 1983 along with foundation bolt and accessories unit weight 10 tone3 approximate as per attached drawing & specification....