Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39916173 work of replacement of damaged 33 kv power supply from 220 kv sub station under power distribution division d ii, orai to 33 / 11 kv power sub station near railway crossing village chamari and 33 / 11 kv power sub station feeding babina. work of replacement of old and dilapidated ( 1+2 ) vcb machine installed at parosa. 2 carriage offollowing line materials for 11 kv line from center store to thesite of work including measuring weiging loading unloading at both ends and proper stacking at safe site. 3 33 kv xlpe cable 3x300 mm 4 o / d cable jointing kit suitable for 33 kv xlpe cable 3x300 mm 5 hdpe pipe 6 dia 6 11 kv vcb, i / c ctr 600 / 300 / 5a 7 11 kv vcb, o / g ctr 200 / 100 / 5a 8 part b 9 erection of the following supports after making of pits as per resspo norms & filling of pits by concrete of ratio 1:4:8 ( cement brick balast & sand ) . fitting of all accessories as cross arm, top channel, bracing angle, pin insulator, disc insulator, danger board, number plate, barbed wire & clamps etc. plinthing of support above 300mm ground level by concrete of ratio 1:4:8 ( cement brick balast & sand ) will be done at the time of erection of pole. painting of st pole structure as per resspo norms also ( all type of paints, red oxide primer, nut, bolts & grouting material etc. will be provided by contractor ) . 10 33 kv xlpe cable 3x300 mm as per resspo norms 11 o / d cable jointing kit suitable for 33 kv xlpe cable 3x300 mm as per resspo norms 12 hdpe pipe 6 dia as per resspo norms 13 laying of cable under railway crossing by drill method as per resspo norms 14 laying of cable ( underground ) as per resspo norms 15 mouting of cable to poleas per resspo norms 16 making a cable box as per resspo norms 17 11 kv vcb, i / c ctr 600 / 300 / 5a as per resspo norms 18 11 kv vcb, o / g ctr 200 / 100 / 5a as per resspo norms 19 dismantling & carriage etc of old vcb to store 20 clearing of the line route by cutting of tree branches during erection of line and also upto the time of energisation of site incharge...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39916025 schedule of work / technical specification for misc construction of 33 kv line for feeding of 33 / 11 kv sub station sonta ( distt. muzaffarnagar ) from 220 kv sub station khatauli ( muzaffarnagar ) .; 1 1. supply of following materialg.iangle ( 65×65×6 ) mm 2 g.ichannel ( 125×65 ) mm 3 g.ichannel ( 100×50 ) mm 4 stay sets ( 20×1800 ) mm 5 stay wire g.i 7 / 8 swg 6 g.i wire no. 6 swg 7 g.i wire no. 8 swg 8 m.s. earthing rod 9 v type cross arm 33 kv 10 cross arm holding clamp for pcc pole 9 m + s.t. pole 11 m long & 13m long 11 top channel holding clamp for pcc pole 9 m + s.t. pole 11 m long & 13m long 12 stay clamp for pcc pole 9 m + s.t. pole 11 m long & 13m long 13 guarding clamp for s.t. pole 11 m & 13m long 14 f bracket for 33 kv 15 e bracket for 33 kv 16 danger board with clamp for pcc pole 9 m + s.t. pole 11 m long & 13m long 17 number plate with clamp for pcc pole 9 m + s.t. pole 11 m long & 13m long 18 braccing clamps clamp for pcc pole 9 m + s.t. pole 11 m long & 13m long ( upper & lower ) 19 aluminum binding wire 20 barbed wire 21 grouting of stay 22 read oxide paint 23 aluminium paint 24 m.s. bolts nuts & washers 25 earth wire clamp with nut & bolts 26 gi trimling 27 nozling of stay wire 28 eye bolt 29 cable rout marker 30 concreting of support 31 tree cutting compensation 32 stone pad ( 300×300×75 ) mm 33 p.g. clamp for dog to dog conductor 34 turn buckle 35 guarding angle 75×75×8 36 gi wire 16swg for binding 37 outdoor type cable jointing kit for 33 kv xlpe cable 38 laying of hdpe 80 pn 150mm pipe 39 g.i pipe 150mm dia 3 mtr long. 40 2. safe carriage of with loading & unloading at both ends respectively. ( under jurisdiction of pvvnl ) a ) acsr dog conductor 41 b ) 33 kv pin isulators ( polymer ) 42 c ) disc insulators b&s 7000 kg. ( polymer ) 43 d ) disc fittings b&s for dog 70 kn ( polymer ) 44 e ) pcc pole 9 m long 45 f ) steel tublar pole sp 55 11m ( bottom portiongalvanized ) 46 g ) steel tublar pole sp 72 13m ( bottom portiongalvanized ) 47 h ) 33 kv, 3×300mm² xlpe cable 48 a erection of support after excavation of foundation pit in mix soil / normal soil / soft & hard rock and its back filling and leveling etc. the size of the pit will be ( 900×600 ) mm and having depth of 1 / 6th of the full length of the support & erection of support. the work includes carriage and handling of supports from site store to pit site. ( i ) 9 mtr. p.c.c. poles 49 ( ii ) 11 m long stp, sp 55 round pole 50 ( iii ) 13 m long stp, sp 72 round pole 51 b fixing of all clamps, cross bracing sets 3.5 mtr. from m.s. angle 65×65×6mm / 50×50×6mm & other accessories on the supports as per drawing. work includes cutting of holes and providing m.s. bolts of 16×40mm size in the middle of cross bracing with 1 no. spring washer. the work also includes carriage & handling of accessories from sectional store to pit site as well as any fabrication work if required. ( i ) single pole ( a ) 9 mtr. p.c.c. poles 52 11 m long stp, sp 55 round pole 53 13 m long stp, sp 72 round pole 54 ( ii ) double pole structures ( a ) 9 mtr. p.c.c. poles 55 ( b ) 11 m long stp, sp 55 round pole 56 ( c ) 13 m long stp, sp 72 round pole 57 ( iii ) tri pole structures ( a ) 9 mtr. p.c.c. poles 58 ( b ) 11 m long stp, sp 55 round pole 59 ( c ) 13 m long stp, sp 72 round pole 60 ( iv ) four pole structures ( a ) 9 mtr. p.c.c. poles 61 ( b ) 11 m long stp, sp 55 round pole 62 ( c ) 13 m long stp, sp 72 round pole 63 stud pole on 9mtr pcc pole 64 stud pole on 11m st pole ( sp 55 ) 65 grouting of supports in cc 1:4:8 ( cement, sand & 40 mm brick ballast ) grouting will be done in the block of size ( 450×450 ) mm ×1 / 6th of full length of the support, up to ground level, 300 mm plinth above the ground level with c.c. 1:3:6 ( cement, course sand and stone grit ) with muffing as per drawing, work includes back filling and proper ramming. ( i ) 9 mtr. p.c.c. poles 66 ( ii ) 11 m long stp, sp 55 round pole 67 ( ii ) 13 m long stp, sp 72 round pole 68 grouting of stay rods ( 20×1800 ) mm including all work of excavation, cement concrete in size ( 0.60 × 0.60 × 0.30 ) m in ratio 1:4:8 cement, sand, 40mm brick ballast ) as per drg. including back filling, proper ramming etc and fixing tightening & nozzling of stay wire with stay rod with the poles of required tension as per drawing. 69 earthing of supports with ms earth rod of ( 20×2500 ) mm long including excavation of pit and driving m.s. rod 3.0 m apart from support and 0.5m below the ground level and connecting below the earth electrodes with the help of g.i. wire no. 8 swg and earthing lugs. 70 laying, spreading, lifting and final sagging of 3 phases of acsr dog conductor in accordance with profile and sag chart including binding, jumpering and fixing of p.g. clamp as per requirement in 03 nos. conductor in parallel. 71 guarding between two poles like single poles, double poles, four poles, etc. to guard lt, 11 kv line telephone and river crossing, road crossing etc. with g.i. wire no. 6 swg and g.i. wire no. 8 swg, including cutting with fabrication and fixing of guarding channel with clamps nut & bolts etc. as per drawing. 72 providing & fixing of danger board at each location as per specification of the drawing with clamps etc. 73 chopping of branches of trees of eucalyptus, neem, keekar and other kind of trees along the route of the line and disposal of the same at suitable place. 74 making h.t. connections of the proposed line, on to the existing 33 kv bay / line from where line is eminating and another at the end of line to the terminal gantry at proposed 33 kv sub station. the work consists of fixing of tension fitting, insulators, jumpering, clamping and binding etc. at the end as per site conditions. 75 painting of following supports / structures with 2 coats of synthetic enamel paint after one coat of ready mix primer including cost of all material, as well as rubbing / cleaning of surface as required for proper completion of work. painting will be done by post office red paint from top to cross arm and remaining by aluminium paint. ( a ) all channels, x arms and clamps of 9 mtr. pcc poles ( i ) single supports 76 ( ii ) double supports 77 ( iii ) tri support 78 ( iv ) four support 79 b ) 11 mtr, sp 55 poles including all channels / x arms / clamps etc ( i ) single supports 80 ( ii ) double supports 81 ( iii ) tri support 82 ( iv ) four support 83 c ) 13 mtr, sp 72 poles including all channels / x arms / clamps etc. ( i ) single supports 84 ( ii ) double supports 85 ( iii ) tri support 86 ( iv ) four support 87 wrapping of barbed wire on 33 kv pcc poles / sp 55 st & sp 72 st poles as anti climbing device for a length of 0.9 mtr., wire pitch / gap 13mm and fixing upper and lower end keeping lower end at a height of 2.75 mtr. from the ground complete with supply and fixing of lower end & upper end clamps made of m.s. flat 40×5mm complete with nuts & bolts & all other required material. 88 numbering of each supports by preparing background with dark yellow paint in the size of 150mm dia and writing support number 100mm high with black paint. 89 12.h.t. power cable laying :i ) digging of trench of size 900x1050 mm for laying of 33kv cable including loops. 90 ii ) safely laying of33kv 3x300mmsq xlpe cable in cable trench by laying 2 no. cables in each trench. ( single circuit laying ) 91 iii ) safe laying of 33kv xlpe cable in air on d / p / f / p. 92 iv ) laying of ist class bricks along the length on both sides and stone slab 650x450x40 as a top cover over the xlpe cable in trench. ( single circuit laying ) ( as per respo norms ) 93 v ) filling river sand in side beneath & around cable in the trench. 94 v ) back filling of excavated earth in the cable trench up to the ground level and remming properly. 95 v ) filling river sand in side beneath & around cable in the trench. 96 vi ) making of 33kv outdoor type heat shrink xlpe cable box of size 3x300mmsq and crimping of proper size aluminium lugs. work includes providing insulating tapes etc. 97 vii ) fixing 150mm dia 3 mtr long g.i pipe over 33kv 3x300 mm2 xlpe cable before mounting the cable on double pole structure. this work includes supply & fixing of clamps, nut bolt, sealing of top and bottom of pipe and one end of pipe is to be buried under earth about 500mm including laying of cable in pipe. 98 viii ) underground railway / highway cable crossinglaying of 01 nos. 33 kv 3×300mm² xlpe cable crossing railway / highway line between station muzaffarnagar to khatuli at dilhi railway line ( distt. muzaffarmagar ) . dfccil ( a ) boring of earth under the railway track of size 300mm dia tunnels ( 01 nos. ) for 33 kv, 3×300mm²xlpe cable. the tunnel will be excavated about 3 mtr. from the top of railway track matching with item no.a ) safely laying of hdpe 80 pn 150mm pipe by trienchlessmethode in double layertunnel under railway track for laying 33 kv xlpe cable 99 ( c ) safely laying of 01 nos. 33 kv, 3×300 mm² xlpe cable in hdpe 80 pn 150mm with minimum gap of 450mm between both cables from one double pole to other side of double pole. 100 d ) railway crossings 01 no. / highway crossing 02 no.documentation & survey work ( excluding bank gurantee and way leave charges ) 101 e ) making of 33 kv outdoor type heat shrinkable xlpe cable jointing boxes and crimping of proper size aluminum lugs. work includes providing insulating tapes etc. as per specifications.. 102 ( f ) laying of 3×300mm² xlpe cable in the air and mounting and clamping 33 kv xlpe boxes on double pole structure and making connection with 33 kv overhead lines at both ends. 103 ( g ) fixing 150mm dia 3mtr. long g.i. pipe over 33 kv 3×300mm² xlpe cable before mounting the cable on double pole. work includes fixing of clamp, sealing on top and bottom end of the g.i. pipe. one end of g.i. pipe is to be butied under earth about 500mm....

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39915510 construction / extension of h.t. & l.t. line and different capacity of 11 / 0.4 kv s / s in different places. work under the head of additional business plan 2023 24. under geographical area of electricity distribution division shrawasti. 1 loading, unloading and safe cartage of the following materials from electricity store centre, bahraich/ shrawasti to the work site/j.e dump store (distance up to 80 km) 2 st poles (11 mtr long) 3 pcc poles (9 mtr long) 4 pcc poles (8.5 mtr long) 5 acsr weasel conductor 6 acsr dog conductor 7 100 kva t/f 8 3x50+1x35+1x16 sq mm 9 3x95+1x70+1x16 sq mm 10 11 kv cable al. 3x300sq.mm.xlpe. 11 11 kv cable al. 3x185sq.mm.xlpe. 12 11 kv cable jointing kit 3x300sq.mm.xlpe.i/d 13 11 kv cable jointing kit 3x300sq.mm.xlpe.o/d 14 11 kv cable jointing kit 3x185sq.mm.xlpe.i/d 15 11 kv cable jointing kit 3x185sq.mm.xlpe.o/d 16 distribution box 17 structure for 33 kv isolator. 18 33 kv lightening arrester. 19 line isolator 800a,33kv 20 33 kv ct 400/200/1 1 1a 21 33 kv pt(outdoor) 22 33 kv vcb 23 33 kv control pannel for double transformer 24 33 kv control panel for single feeder 25 33 kv control panel for double feeder 26 33 kv control panel for single transformer. 27 control cable 6x2.5sq.mm. 28 control cable 4x2.5sq.mm. 29 control cable 2x2.5sq.mm. 30 structure for vcb & ct 31 other line materials(centralized items) 32 erection of single st poles (11 mtr long) for 11 kv/h.t. line alongwith fitting of all accessories on pole including dragging of pole from dump site to pit site. 33 erection of single pcc (9 mtr long) for 11 kv/h.t. line alongwith fitting of all accessories on pole including dragging of pole from dump site to pit site. 34 erection of single pcc (8.5 mtr long) for 11 kv/h.t. line alongwith fitting of all accessories on pole including dragging of pole from dump site to pit site. 35 erection of sectional double st poles (11 mtr long) for 11 kv/h.t. line alongwith fitting of all accessories on pole including dragging of pole from dump site to pit site. 36 erection of sectional double pcc poles (9 mtr long) for 11 kv/h.t. line alongwith fitting of all accessories on pole including dragging of pole from dump site to pit site. 37 erection of sectional double pcc poles (8.5 mtr long) for 11 kv/h.t. line alongwith fitting of all accessories on pole including dragging of pole from dump site to pit site. 38 erection of sectional four pole st poles (11 mtr long) for 11 kv/h.t. line alongwith fitting of all accessories on pole including dragging of pole from dump site to pit site. 39 laying, stringing, sagging & binding of acsr weasel conductorof 11 kv & 33 kv line in 3 phase, 3 wire line with jumpering (where as required) 40 laying, stringing, sagging & binding of acsr dog conductorof 11 kv & 33 kv line in 3 phase, 3 wire line with jumpering (where as required) 41 construction of 11/0.4 kv s/s for following capacity of t/f with mounting and fitting of t/f on plinth/double pole with proper fitting of all acessories and connecting with all circuit including earthing of t/f fitting with all accessories. 42 100 kva t/f 43 laying, stringing & sagging of 3x50+1x35+1x16 sq mm.up to proper sag 44 laying, stringing & sagging of 3x95+1x70+1x16 sq mm.up to proper sag. 45 laying of 11 kv cable al. 3x300sq.mm.xlpe. 46 laying of 11 kv cable al. 3x185sq.mm.xlpe. 47 installation & fixing of 11 kv cable jointing kit 3x300sq.mm.xlpe.i/d 48 installation & fixing of 11 kv cable jointing kit 3x300sq.mm.xlpe.o/d 49 installation & fixing of 11 kv cable jointing kit 3x185sq.mm.xlpe.i/d 50 installation & fixing of 11 kv cable jointing kit 3x185sq.mm.xlpe.o/d 51 earthing of pole as per resspo norms. 52 earthing of comolite(gi pipe, bore type 40 feet) as per resspo norms. 53 erection and grouting of stay sets alongwith complete fittings. cement, sand & brick ballast provided by the contractor at his own cost. 54 grouting of poles with 1:4:8cc ratio of cement, sand & brick ballast, backfilling of pits with mud completely. all required materials shall be provided by the contractor at his own cost. 55 mounting and fixing of l.t. distribution box alongwith fitting of all accessories. 56 fixing of 33 kv cable jointing kit. 57 installation of structure for 33 kv isolator. 58 installation of 33 kv lightening arrester. 59 installation of line isolator 800a,33kv 60 installation of33 kv ct 400/200/1 1 1a 61 installation of 33 kv pt(outdoor) 62 installation of 33 kv vcb 63 installation of 33 kv control pannel for double transformer. with fitting of all accessories for completion of work. (rest material will be provided by the contractor as per resspo norms.). 64 installation of 33 kv control panel for single feeder with fitting of all accessories for completion of work. (rest material will be provided by the contractor as per resspo norms.). 65 installation of 33 kv control panel for double feeder with fitting of all accessories for completion of work. (rest material will be provided by the contractor as per resspo norms.). 66 installation of 33 kv control panel for single transformer with fitting of all accessories for completion of work. (rest material will be provided by the contractor as per resspo norms.). 67 installation of control cable 6x2.5sq.mm. 68 installation of control cable 4x2.5sq.mm. 69 installation of control cable 2x2.5sq.mm. 70 installation of structure for vcb & ct 71 gaurding of 11 kv line with complete fittings. 72 decentralized items: providing and fixing offollowing materials sanctioned estimate/package as per resspo u.p.p.c.l. drawing/ norms.(where is required). 73 dead end clamp. 74 suspension clamp. 75 lt clamp. 76 ms nut and bolts. 77 clamp with nut and bolts. 78 aluminium binding wire 79 welding gi strip 80 x arm holding clamp 81 stone pad 82 piercing connector. 83 earth wire clamp with bolts & nuts. 84 f bracket for 11kv/33 kv 85 barbed wire gi 86 number plates with clamp and nut & bolts. 87 pg clamp 88 aluminium jointing sleeves 89 aluminum paint 90 red oxide paint 91 guarding clamp ...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39915125 increasing capacity ( 250 to 400 kva ) of 02 nos. transformer at pahadpur near gudamba thana & devi tali mandir in the work area of sub division engineering college under jurisdiction of edd rahim nagar, lesa, trans gomti, lucknow in the head ofadditional business plan 2023 24 loading, carriage & unloading of following materials from centre store daliganj to work site and its stacking. distance approx ( 0 35 ) kms. 2 line material 3 stp pole 9 / 11 mtr. long. 4 250 / 400 kva t / f 5 lt pvc cable 1x400 / 3.5x 240 / 1x 70sqmm 6 abc ( 3x120 / 95 / 70 / 25 / 16 ) sqmm. 7 11 kv xlpe cable ( 3x35 / 70 / 120 / 170 / 185 ) 8 11 kv cable jointing kit o / d ( 3*70 / 120 / 185 ) sq mm 9 fabrication, erection of sub station type double pole on 8.5 mtr long pcc / 11 mtr. long st pole along with fixing of necessary clamps. accessories required including supply & fixing of straight ms 100x50mm top channel ( 2240mm long ) one no. dropper channel / angle 100x50 mm 2 nos. with arrangement of fixing 3 nos. pin insulator as per respo specification and direction of e / i. only pole & insulator supplied by the deppt. 10 construction of t / f plinth of size 2x2x1.2 meters with help of 1st class bricks and massonary in the ratio 1:4 cement & sand coarse, filling the structure completely as per norms with rcc top 1:2:2 cement, sand coarse, stone grit with ms bar and ms channel for resting t / f. all material shall be arranged by the contractor. 11 wiremessfencing of 11 / 0.4 kvs / s shall be made of rectangular of size as per site requirement not exceeding 3 meter fabrication 45x45x5 mm angle the frame is also have 1 no. horizontal runner of ms flat 40x5 welded in middle to support of wire mess. rectangular welded type wire mess of size 50x25 made of 12 s.w.g. wire mess shall be welded all along the periphery of theframe as well as on horizontal runner to give extra strength of welding to wire mess welded on the frame. diagonal bracing of all the frame panel will be welded with ms flat of size 25x3mm to support as per respo specification & direction of e / i. 12 construction of masonry type distribution pillar box with first class brick ballast cement, coarse sand, local sand, brick ballast and ms round bar of 10 mm dia including supply and mounting of 02 nos. straight ms angle 50x50x6x750 mm 2 nos., henely type tailless fuse units 500 amps. 650 volts one no. for incoming and other for outgoing, copper bus bar 4 nos. 1000x50x6 mm with locking arrangement made of 18 swg bp sheet. 13 providing and fixing of 11 kv do fuse set along with clamps & nut bolts on existing of double pole. 14 providing and fixing of 11 kv tpmo along with clamps & nut bolts on existing of double pole. 15 ordinary earthing by ms earth rod 2500mm long as per respo schedule. only gi wire& earth rod shall be supplied by the department. 16 erection & commissioning of ( 3x120 / 95 / 70 / 25 / 16 sq.mm ) aerial bunched conductor. 17 laying oflt pvc cable 1x400 / 3.5x240 sqmmas respo specification & direction of e / i. 18 earthing of t / f pipe type with 60 fit deep borring and providing gi pipe 1.5 dia ( 60 fit gi pipe ) and gi strip 25x5 mmx6 meter long attached with clamps, l piece, nut & bolts and gi pipe cap. all material shall be supplied by the contractor. 19 safe installation of 250 / 400 kva t / fon double pole / plinth by providing and fixing of all accessories along with making ht / lt connection and its commissioning. 20 dismantling of 250 kva t / f on exsiting plinth along with dragging, loading cartage and unloading to work site j.e dump store / central store. 21 supply and fixing 22 aluminium lug 400 sq mm 23 lt clamp with i hook 24 lt bearer connector 25 lt connector b type 26 denger board wityth clamp 27 dead clamp 28 number plate 29 barbed wire 30 suspension clamp 31 copper l piece 32 gst will be paid extra as per rule....

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39914166 carrying out various works on semi turn key basis for system augmentation, . strengthening in the area of ee, eudd i, mathura under the jurisdiction of se, eudc, mathura 1 cartage of following material from store centre, mathura to work site. 2 st pole ( 11 mtr. long ) ( bottom portion galvanized ) 3 st pole pole ( 13 mtr. long ) ( bottom portion galvanized ) 4 630 kva t / f 5 250 kva t / f. 6 100 kva t / f. 7 lt aerial bunch conductor. 8 lt xlpe / pvc cable 1cx630 sq.mm. 9 lt xlpe / pvc cable 1cx400 sq.mm. 10 lt xlpe cable of size 3.5x400 sq. mm. 11 lt xlpe cable of size 3.5x240 sq. mm. 12 lt xlpe cable of size 3.5x150 sq. mm. 13 lt xlpe cable of size 3.5x70 sq. mm. 14 33 kv xlpe cable 3x300 sq.mm. 15 11 kv xlpe cable 3x70 sq.mm. 16 11 kv xlpe cable 3x185 sq.mm. 17 11 kv xlpe cable 3x300 sq.mm. 18 33 kv vcb 800 a, 750 mva 19 33 kv control panel for single t / f 20 33 kv control panel for double t / f 21 33 kv 3x300 sq.mm. outdoor type cable jointing kit 22 11 kv 3x70 sq.mm. outdoor type cable jointing kit 23 lt h / s jointing kit 3.5x240 straight through 24 lt h / s jointing kit 3.5x150 straight through 25 lt h / s jointing kit 3.5x70 straight through 26 11 kv fuse set 27 11 kv tpmo 28 11 kv bus coupler 29 acsr dog / weasel / ins. weasel conductor 30 other line material such as cross arm, ms bracing set, ms top channel, bottom channel, tee channel with clamp , clamps, pin insulator, disc insulator nut & bolts, earth rod, earth wire, v type x arm, f bracket, guarding wire, etc. 31 cartage of above material from store center, mathura to work site ( cartage rates are acceptable for only those materials, which are to be carriage from store center, mathura to work site ) 32 grouting of st pole with cement, sand, concrete, ( cc will be of cement, coarse sand & brick balleast grouting will be done with the help of wooden / steel formers in a block of size 900mm x 450mm x 1 / 3 of the full of the support in the cc 1:4:8 as per relevant drawing including back filling & proper ramming. 33 digging of pit & erection of new single support st pole ( 13 / 11 mtr. long ) including grouting of pole and fixing of all clamps, cross arm, pin / disc insulator & other accessories with providing stone pad as per relevant drawings. any fabrication if required for above support. 34 digging of pit & erection of new four pole structure st pole ( 13 / 11 mtr. long ) including grouting of pole and fixing of all sturucture accessories, clamps, cross arm, pin / disc insulator & other accessories with providing stone pad as per relevant drawings. any fabrication if required for above support. 35 digging of pit & erection of new tri pole structure st pole ( 13 / 11 mtr. long ) including grouting of pole and fixing of all sturucture accessories, clamps, cross arm, pin / disc insulator & other accessories with providing stone pad as per relevant drawings. any fabrication if required for above support. 36 digging of pit & erection of new double pole structure st pole ( 13 / 11 mtr. long ) including grouting of pole and fixing of all sturucture accessories, clamps, cross arm, pin / disc insulator & other accessories with providing stone pad as per relevant drawings. any fabrication if required for above support. 37 provinding & fixing of 24 volt battery with battery charges 38 installing / fixing of delta earthing for i / c vcb 39 earthing of st / pcc pole / body earthing of t / f. by m.s earth rod. 40 providing & fixing of ms nut, bolt and washers 41 providing & painting of st pole. 42 digging of pit & erection of stay rod with grouting cement sand and brick ballast including nuzzling, binding complete. ( stay insulator providing by contractor ) 43 installation of 33 kv vcb 800 a, 750 mva 44 installation of control pannel for single t / f 45 installation of control pannel for double t / f 46 supply and laying of control cable 4x2.5 sq.mm. 47 supply and laying of control cable 2x2.5 sq.mm. 48 plinth & foundation of 33 kv vcb 49 pipe in pipe gel earthing for 33 kv vcb & control panel 50 sagging of 33 / 11kv / lt line on dog / weasel conductor on erected poles. 51 providing & sagging of 33 kv line on panther conductor on erected poles 52 laying of ab conductor for lt line on erected poles. 53 laying of lt pvc cable 1cx630 sq.mm. 54 laying of lt pvc cable 1cx400 sq.mm. 55 laying of u / g. lt xlpe cable of size 3.5x400 sq. mm. with complete job 56 laying of u / g. complete work of lt xlpe cable of size 3.5x240 sq. mm.with complete job 57 laying of u / g. complete work of lt xlpe cable of size 3.5x150 sq. mm.with complete job 58 laying of u / g. complete work of lt xlpe cable of size 3.5x70 sq. mm.with complete job 59 guarding of 33 / 11kv line. ( including g.i. wire and other related items ) 60 providing & fixing of guarding angle for 33 / 11 kv line 61 providing & fixing of i bolt for guarding 62 providing & fixing of aluminium biding wire for guarding 63 providing & fixing of clamp for guarding angle for 11 kv line 64 providing & fixing of earth wire clamp 65 providing & fixing of danger board 66 providing & fixing of barbed wire 67 providing & fixing of stone pad 68 providing & fixing of p.g. clamp 69 fixing of 33 / 11 kv v type steel cross arm 70 fixing of 11 kv pin insulator with pin 71 fixing of 33 kv pin insulator with pin 72 fixing of disc insulator 45 kn & 70 kn ( t&c / b&s ) 73 fixing of disc fitting 45 kn & 70 kn ( t&c / b&s ) 74 providing & fixing of 33 kv / 11 kv f bracket 75 providing & fixing of packing piece clamp for 33 kv / 11 kv with nut & bolts 76 providing & fixing of aluminium lug 150 / 240 / 400 / 630 77 providing & fixing of st pole clamp 78 providing & connecting earthing strip 79 fixing & filling of 33 kv 3x300 sq.mm. outdoor type cable jointing kit 80 fixing & filling of 11 kv 3x70 sq.mm. outdoor type cable jointing kit 81 fixing & filling of lt h / s jointing kit 3.5x240 straight through 82 fixing & fixing of lt h / s jointing kit 3.5x150 straight through 83 fixing & fixing of lt h / s jointing kit 3.5x70 straight through 84 installation of 11 / 0.4 kv, 630 kva t / f mobile trolley 85 trolley structure for 630 kva t / f with vehicle tyre, rim, coupling, trolly hook, earthing, painting and related accessories with complete job 86 providing & fixing / installation of a 2 type lt panelsupply &erracetionoffactory fabricated&wired metalcladdustandverminprooffloormounting double door type outdoor application, with m.s. channel base with bottom and top cable entreis shell be detachable type gland plateelectricalcontrolpanelwithtpnmccbs ( fourpole50kawith thermalmagnaticrelease with adjustable over current and short circuit protection, ics=100% icu, suitable for 415 v ac ) switchesandinstrument chamber etc.complete in all respects. the instrument chamber shallbeseparate and incomming section connecting with proper horizental / vertical busbar and outgoing section cable alley sectionandshall metering with digital multifuncation meter, with inbuilt selector switches, istrument fuses, red yellow band blue phase indicators in in comming section, currenttransormeretc.the boardshallhave suitablecapacity electrolyticaluminiumbusbarsas peris8623insulatedwithheatshrink color codesleevand mounted on non hygroscopic supports such as cmc / dmc support with deteachable side covers and shall be suitable for extension on the sides. the switches entryboxesshallbecompletewithsuitablecable end boxes.the jobincludesthe disconnecting anddismentling of existing b 1 type distribution panel including of complete replace old burn cables ends and joint new cable with cable jointers, luges, double compression glands, etc new cables will joint as per connected sizes in incoming and outgoing sectionsgrounting ofthe panel boardas per directionsofengineer incharge.incoming : 400 ampmccb1 noand outgoing 250 amp mccb 03 nos, 160 amp 03 nos. with extended rotary handel, spreder set , phase barrier etctheswitchboardshallbe fabicated with gelvnized primesheet with a minimum thickness of 1.6 mm / 2mm. with c 9 tank process powder coated other conditions also 87 providing & fixing / installation of a 3 type lt panelsupply &erracetionoffactory fabricated&wired metalcladdustandverminprooffloormounting double door type outdoor application, with m.s. channel base with bottom and top cable entreis shall be detachable type gland plateelectricalcontrolpanelwith tpnmccbs ( fourpole50kawith thermalmagnaticrelease with adjustable over current and short circuit protection, ics=100% icu, suitable for 415 v ac ) switchesandinstrument chamber etc.complete in all respects. the instrument chamber shallbeseparate and incomming section connecting with proper horizental / vertical busbar and outgoing section cable alley sectionandshall metering with digital multifuncation meter, with inbuilt selector switches, istrument fuses, red yellow band blue phase indicators in in comming section, currenttransormeretc.the boardshallhave suitablecapacity electrolyticaluminiumbusbarsas peris8623insulatedwithheatshrink color codesleevand mounted on non hygroscopic supports such as cmc / dmc support with deteachable side covers and shall be suitable for extension on the sides. the switches entryboxesshallbecompletewithsuitablecable end boxes. incoming : 630ampacb 1 noand outgoing 250 amp mccb 5 nos and 100 amp mccb 2 nos with extended rotary handel, spreder set , phase barrier etctheswitchboardshallbe fabicated with gelvnized primesheet with a minimum thickness of 1.6 mm / 2mm. with c 9 tank process powder coated.the jobincludesthe disconnecting anddismentling of existing a 3 type distribution panel including of complete replace old burn cables ends and joint new cable with cable jointers, luges, double compression glands, etc new cables will joint as per connected sizes in incoming and outgoing sectionsgrounting ofthe panel boardas per directionsofengineer incharge. 88 providing & fixing / installation of a 1 type lt panelsupply &erectionoffactory fabricated&wired metalcladdustandverminprooffloormounting double door type outdoor application, with m.s.channel base with bottom and top cable entries shall be detachable type gland plateelectricalcontrolpanelwithtpnacb ( 65 ka, 4pole elect draw out , micro processer release icu=icw=ics 1sec ) with short circuit protectionand tpnmccbs ( fourpole50kawith thermalmagneticrelease with adjustable over current and short circuit protection, ics=100% icu, suitable for 415 v ac ) switchesandinstrument chamber etc. complete in all respects. the instrument chamber shallbeseparate and incoming section connecting with proper horizontal / vertical busbar and outgoing section with cable alley sectionandshall metering with digital multifunction meter with inbuilt selector switches, instrument fuses, red yellow and blue phase indicators in incoming section, currenttransformeretc.the boardshallhave suitablecapacity electrolyticaluminumbusbarsas peris8623insulatedwithheatshrink color codesleeveand mounted on non hygroscopic supports such as cmc / dmc support with detachable side covers and shall be suitable for extension on the sides. the switches entryboxesshallbecompletewithsuitablecable end boxes. ( incoming : 1250ampacb1 noand outgoing 400 amp mccb 6 nos and 250 amp mccb 2 nos with extended rotary handel, spreder set , phase barrier etc ) theswitchboardshallbe fabricated with galvanized primesheet with a minimum thickness of 1.6 mm / 2mm. with seven tank process powder coated switchgear.the jobincludesthe disconnecting anddismantling of existing a 1 type distribution panel including of complete replace old burn cables ends and joint new cable with cable jointers, luges, double compression glands, etc new cables will joint as per connected sizes in incoming and outgoing sections, the grounding ofthe panel boardas per directionsofengineer incharge. 89 providing & fixing / installation of b 1 type lt panelsupply &erracetionoffactory fabricated&wired metalcladdustandverminprooffloormounting double door type outdoor application, with m.s. channel base with bottom and top cable entreis shell be detachable type gland plateelectricalcontrolpanelwithtpnmccbs ( fourpole50kawith thermalmagnaticrelease with adjustable over current and short circuit protection, ics=100% icu, suitable for 415 v ac ) switchesandinstrument chamber etc.complete in all respects. the instrument chamber shallbeseparate and incomming section connecting with proper horizental / vertical busbar and outgoing section cable alley sectionandshall metering with digital multifuncation meter, with inbuilt selector switches, istrument fuses, red yellow band blue phase indicators in in comming section, currenttransormeretc.the boardshallhave suitablecapacity electrolyticaluminiumbusbarsas peris8623insulatedwithheatshrink color codesleevand mounted on non hygroscopic supports such as cmc / dmc support with deteachable side covers and shall be suitable for extension on the sides. the switches entryboxesshallbecompletewithsuitablecable end boxes.the jobincludesthe disconnecting anddismentling of existing b 1 type distribution panel including of complete replace old burn cables ends and joint new cable with cable jointers, luges, double compression glands, etc new cables will joint as per connected sizes in incoming and outgoing sectionsgrounting ofthe panel boardas per directionsofengineer incharge.incoming : 400 ampmccb1 noand outgoing 250 amp mccb 03 nos, 160 amp 03 nos. with extended rotary handel, spreder set , phase barrier etctheswitchboardshallbe fabicated with gelvnized primesheet with a minimum thickness of 1.6 mm / 2mm. with c 9 tank process powder coated switchgear 90 providing & fixing / installation of b 2 type lt panelsupply &erracetionoffactory fabricated&wired metalcladdustandverminprooffloormounting double door type outdoor application, with m.s. channel base with bottom and top cable entreis shall be detachable type gland plateelectricalcontrolpanelwith tpnmccbs ( fourpole50kawith thermalmagnaticrelease with adjustable over current and short circuit protection, ics=100% icu, suitable for 415 v ac ) switchesandinstrument chamber etc.complete in all respects. the instrument chamber shallbeseparate and incomming section connecting with proper horizental / vertical busbar and outgoing section cable alley sectionandshall metering with digital multifuncation meter, with inbuilt selector switches, istrument fuses, red yellow band blue phase indicators in in comming section, currenttransormeretc.the boardshallhave suitablecapacity electrolyticaluminiumbusbarsas peris8623insulatedwithheatshrink color codesleevand mounted on non hygroscopic supports such as cmc / dmc support with deteachable side covers and shall be suitable for extension on the sides. the switches entryboxesshallbecompletewithsuitablecable end boxes. incoming : 200 ampmccb1 noand outgoing 125 amp mccb 6 nos with extended rotary handel, spreder set , phase barrier etctheswitchboardshallbe fabicated with gelvnized primesheet with a minimum thickness of 1.6 mm / 2mm. with c 9 tank process powder.the jobincludesthe disconnecting anddismentling of existing b 2 type distribution panel including of complete replace old burn cables ends and joint new cable with cable jointers, luges, double compression glands, etc new cables will joint as per connected sizes in incoming and outgoing sectionsgrounting ofthe panel boardas per directionsofengineer incharge. 91 providing & fixing / installation of c type lt paneldisconeccting and dismentlingof existing c panel and supply, installation testing commisioning offactory fabricated&wired metalcladdustandverminproof double door typeoutdoor application stand mounting, m.s. channel base incliding channel stand with bottom cable entreis the panel boardshall havesuitablecapacity electrolytic alumininum busbars asper is8623 or above istulated with heat shrink sleeving and mounted on nonhygroscopic supports such as cmc / bmc support. panel shall be completewithsuitablecableendboxes, double compression glands. panel comparment having special provision for internal locking system for stop the electricity theft the panelboard shall be fabricated with gelvnized prime sheet with a minimum thickness of 1.6mm / 2mm. with seven tank process powder coated. panel haveing proper space for connectingincomming and outgoing cable terminations. 92 providing & laying of hdpe pipe 160 mm od pn 4 pe 80 grade uv stabilized hdpe as per is: 4984 of 6 meter length with complete work of cable laying 93 horizontal drilling underground installation piping hdpe pipe 160mm dia with minimum depth of pipe 1.2 below surface for double circuit length of line 94 laying of 33 / 11 kv xlpe cable in double pole structure / loop etc. 95 digging of trench by excavation of earth 0.90 / 1.5 mtr. deep put brick on both side, filling of sand & brick on cable & earth ramming and dressing properly with complete job of laying 33 / 11 kv xlpe cable in trench 96 installation of d.o. fuse set of 11 kv 97 providing and installation of 11 kv r.m.u. ( as per elclosed technical specification ) 98 installation of tpmo of 11 kv 99 concreting of pole ( st 13 mtr. / 11 mtr. ) pcc pole 100 installation & fixing of bus coupler along with provding accessories & complete installation of 11 kv bus coupler 1250 amp. copper flat with nut & bolt others acc. for connection 02 different i / c 101 removal of old transformer ( 160 / 100 / 63 / 25 / 16 kva ) with all connected accessories from existing double pole. 102 the construction of new plinth of size 5’x5’x4’ aboveground level and one ft. below the ground level for 400 / 250 kva transformer 103 installation of following transformer on plinth / double pole with all connecting accessories jumering etc. including carriage of transformers from store centre, mathura to work site. 104 250 kva transformer on plinth 105 100 kva transformer on double pole structure 106 providing and installation of tail less unit complete with structure 107 construction of m.s angle fencing of size ( 3m x3m x2m ) around the plinth of 400 / 250 kva transformer and gap between the m.s angle should not be more than 65mm. 108 complete gel earthingof 11 / 0.4 kv 250 / 400 distribution transformer by digging pits 6” dia upto 3 mtr. deep including chemical filled pipe in between ( pipe in pipe ) isi mark b grade & connecting with g.i strip of size 50mm x 6mm with neutral / body of 11 / 0.4 kv distribution transformer to above pipe in pipe ( pip ) and filling of chemical crystalline conductive mixture containing highly conductive material around the ( pipe in pipe ) up to 3 mtr. including making of chamber at the top of the earthing. other details are as below: 1.earth pipe material – mild steel, galvanised.2 main electrode diameter – 42.4mm.3 auxiliary electrode pipe, diameter – 76mm.4 wall thickness of main electrode : 2.6mm.5 wall thickness of auxiliary ist whole: 3.2mm.6 length of earthing electrode ( pip ) : 3 meter. 109 complete job of road restoration as original 110 dismantling of single support st / rail pole ( 13 / 11 / 9mtr. ) with complete accessories and other dismantled as per site requirement and cartage of material from work site to store center, mathura. 111 dismantling of ht line and cartage of material from work site to store centre, mathura. 112 dismantling of ht line and cartage of material from work site to store centre, mathura....

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39914073 tender for line guarding electricity distribution division 11 kv in rath town on the outskirts of rath. 1 supply & erection 2 stp pole 11 m long ( provided by department ) 3 11 kv pin insulator with pin ( provided by department ) 4 11 kv disc insulator with fitting ( provided by department ) 5 stone pad 300x300x75 mm 6 x arm holding clamp with n&b 7 f clamp with n&b 8 11 kv v type x arm 9 gaurding gi wire 10 gaurding angle with clamp 11 ms t off channel with clamp n&b 12 barbed wire 13 oxide paint 14 painting of mark on pole 15 danger plate with n&b 16 grouting of pole...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39911063 ext: tender for line guarding electricity distribution division 11 kv in rath town on the outskirts of rath. 2 stp pole 11 m long(provided by department) 3 11 kv pin insulator with pin (provided by department) 4 11 kv disc insulator with fitting (provided by department) 5 stone pad 300x300x75 mm 6 x arm holding clamp with n&b 7 f clamp with n&b 8 11 kv v type x arm 9 gaurding gi wire 10 gaurding angle with clamp 11 ms t off channel with clamp n&b 12 barbed wire 13 oxide paint 14 painting of mark on pole 15 danger plate with n&b 16 grouting of pole...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39902020 works at proposed replacement of damaged 33kv xlpe cable of existing 33kv line feeding for 33 / 0.4kv substation distt. court, bulandshahr. 1 supply of following materialstay set complete (g.i.stay rod 20x1800mm, stay wire 7/8swg 10kg, guy insulator, g.i.stay clamp, bolt, nut & wasther with concrete grouting) for 33kv line as per specification 2 g.i. wire 6 swg 3 g.i. wire 8 swg 4 g.i. wire 16 swg 5 v type cross arm 100x50x6 mm g.i channel for 33kv line with g.i.clamp 75x10mm size 6 g.i.top channel 125x65x6mm, 3200 mm long (13.10kg/mt) with g.i. clamp of 75x10mm size, bolts, nuts and washers for 33kv line double pole/ four pole 7 g.i. channel 100x50x6 mm, 2400 mm long (9.56kg/mt) with g.i.clamp of 65x8mm for dropper channel of 33kv line double pole/four pole 8 g.i guarding angle 75x75x6 mm, (6.80kg/mt) x 2200mm long. 9 heat shrinkable outdoor type end termination cable jointing kit suitable for 33kv xlpe 3x120 sq. mm.cable 10 carriage of following material from pvvnl store acsr rabbit conductor 11 acsr dog conductor 12 cable h.t.xlpe 33kv 3x120sq.m.m 13 steel tubler pole sp 72 13.00mtr 14 33kv composite polymeric pin insulator. 15 33kv polymer disc insulator b&s 70kn 16 33kv disc fitting b&s dog/racoon 70kn 17 erection of following material & miscellaneous electrical works.the excavation of foundation pit in mix soil/normal soil/soft soil & hard rock as per site condition and its back filling and leveling etc. the size of the pit will be (750x450)mm and having depth of 1/6th of the full length of the support. erection of support, complete with providing & fixing of all g.i.clamps size of 75x10mm, f bracket 75x10mm, g.i.nut bolt & washer, stone pad al. binding wire and other accessories as per drawing. the work includes carriage and handling of supports from sectional store to pit site as well as an fabrication work if required.single pole(a)13m long stp, sp 72 round pole 18 the excavation of foundation pit in mix soil/normal soil/soft soil & hard rock as per site condition and its back filling and leveling etc. the size of the pit will be (750x450)mm and having depth of 1/6th of the full length of the support. erection of support, complete with providing & fixing of all g.i.clamps size of 75x10mm, 65x8mm, g.i.nut bolt & washer, p.g.clamp, stone pad, al. binding wire, e bracket 75x10mm, and other accessories as per drawing. the work includes carriage and handling of supports from sectional store to pit site as well as any fabrication work if required & fixing of cross bracing sets 4.3mtr long, from g.i.angle 65x65x6mm. the work includes cutting holes and providing g.i.bolt of 16x40mm size, in the middle of the cross bracing with 01no. spring washer of proper size as per drawing/ as per schedule.end double pole structures(a)13m long stp, sp 72 round pole 19 grouting of supports in cc 1:3:6 (cement, sand & 20mm stone grift). grouting will be done in the block of size (450x450)mm x1/6th of full length of the support, upto ground level, 300mm plinth above the ground level with c.c. 1:3:6 (cement, course sand and stone grift) with muffing as per drawing. work includes back filling and proper ramming.single pole(a)13m long stp, sp 72 round pole 20 end double pole structures(a)13m long stp, sp 72 round pole 21 grouting of stay rods (20x1800)mm including all work of excavation, cement concrete in size (0.60x0.60x0.30)m in ratio 1:3:6 cement, sand, 20mm stone grift) as per drg. including back filling of soil and proper ramming etc. 22 fixing, tightening & nozzling of stay wire with stay rod with the poles of required tension as per drawing, including providing & fixing of stay insulators of 33kv and stay clamps. 23 providing & earthing of supports with m.s.earth rod of (20x2500)mm long including excavation of pit and driving m.s.rod 3.0m apart from suppor and 0.5m below the ground level and connecting belowl the earth electrodes with the help of g.i.wire no.8swg, g.i.nut bolt & washer and earthing lugs. 24 laying, spreading, lifting and final sagging of 3 phases acsr dog conductor in accordance with line chart includidng binding and fixing of all accessories in 03nos. conductor in parallel. 25 making jumpers on sectional pole, by providing & fixing of p.g.clamps of proper sizes, suitable for dog conductor/ 33kv, 3x300sq.mm xlpe cable.end double pole 26 guarding between two poles like single poles, double poles, four poles, etc. to guard l.t., 11kv line telephone line and river crossing, road crossing etc. with g.i.wire no.6swg, g.i.wire no.8swg and g.i.wire no.16swg includingcutting with fabrication and fixing of g.i.guarding angle 75x75x6mm with providing & fixing g.i.clamps size 75x10mm, g.i.turn buckle, g.i.eye bolt, nut bolts & washer, & bearer wire 04 nos. etc, as per drawing. 27 providing & fixing of smc danger board at each location as per specification of the drawing. size 200mmx250mm & 3mm thickness with g.i.clamp & nut & bolt for 33kv 28 providing & fixing of smc number plate at each location as per specification of the drawing.size 200mmx250mm & 3mm thickness with g.i.clamp & nut & bolt. 29 making h.t.connection of the proposed line from 33kv line. the work consists of fixing & fabrication of dropper channels, & fixing of disc insulators, pin insulators, jumpering withp.g.clamps, clamping and binding etc,as per site conditions. 30 providing & wrapping of barbed wire (2.0kg per pole) on 33kv st poles sp 55/sp 72 as anti climbing device for a length of 0.9mtr. wire pitch/gap 13mm and fixing upper and lower end keeping lower end at a height of 2.75mtr. from the ground, complete with providing and fixing of lower end & upper end clamps made of g.i.flat 40x5mm complete with nuts&bolts. 31 painting of following supports/structures of 33kvline, with two coats of synthetic enamel aluminium paint after one coat of ready mix primer, including cost of all material, as well as rubbing/cleaning of surface as required for proper completion of work: 13mtr sp 72 poles including all channels/x arms/clamps etc.:(i)single supports 32 (ii) end double pole structure 33 digging of trench by excavation of earth of 1050x750mm size for 33kv line 34 safe laying of 33kv, 3x120sq.mm. xlpe cable in cable trench to respective double pole. 35 providing & laying of ist class bricks, along the length on both side of 33kv xlpe cable in cable trench (minium 18no. bricks/mtr per cable) and stone slab of size 400x600x40mm on top of the cable, providing 75mm thickness river sand for cushion beneath and 75mm above the cable as per specification. 36 back filling of excavated earth in the cable trench upto the ground level and ramming properly. 37 supply & laying ofhdpe pipe pe 80, pn 6, dn 160mm dia by hdd trenchless method, as per site requirement. 38 laying of33kv, 3x120sq.mm xlpe cable in hdpe pipe pe 80, pn 6, dn 160mm dia by hdd trenchless method, as per site requirement. 39 laying of 33kv, 3x300sq.mm xlpe cable in the air on cable riser double pole, existing trench cable trench, nala x ing & g.i.pipe and making connection with 33kv over head line at both ends. 40 providing & fixing 150mm dia 2mm thick 3m long g.i.pipe over 33kv, 3x300sq.mm xlpe cable before mounting the 2no. cable on double pole / cable support structure. the work includes providing & fixing of clamp, sealing of top and bottom end of the g.i.pipe. one end of g.i.pipe is to be buried under earth about 500mm. 41 making of 33kv outdoor type cable end termination by heat shrinkable xlpe cable jointing kits and crimping with proper size aluminium lugs. work includes providing aluminum lugs, insulating tapes etc as per specifications. 42 supply & fixing of cable route marker along the route of 33kv cable with proper grouted with proper painting & marking pvvnl, 33kv ht cable. 43 road restoration charges for 1mtr wide kuccha road (inter locking tiles, bricks road & developed green belt only) or deposite charges to take the permission/approval/noc from any development authority/govt. body/forest deptt./and other concerned deptt. for restoration of damaged property like kuccha road, inter locking tiles and other utilities. 44 road restoration charges for 1mtr wide pucca road (cemented, concrete & black road only) or deposite charges to take the permission/approval/noc from any development authority/govt. body/forest deptt./and other concerned deptt. for restoration of damaged property like pucca road, inter locking tiles and other utilities. ...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39901997 works at proposed construction of new switchyard for shifting of 33 / 11kv substation pahasu, bulandshahr switchyard due to low land level & rain water logging problem in existing switchyard. under edd khurja, bulandshahr. 1 supply of following material terminal gantry galvanized structure as per specification 2 main bus bar complete with dog conductor with g.i.structure as per resspo drawing. 3 line isolator 800a, 33kv 4 bus isolator 800a, 33kv 5 galvanized structure for 33 kv isolator with plinth & foundation as per specification 6 33kv post insulator 7 galvanized structure for 33 kv post insulator with plinth & foundation as per specification 8 33kv lightening arrester with surge counter. 9 galvanized structure for 33 kv lightening arrester with plinth & foundation as per specification 10 33kv fuse set 11 galvanized structure for 33 kv fuse set with plinth & foundation as per specification 12 copper bus bar 2500x50x6mm 13 galvanized structure for cu bus bar 14 power transformer neutral g.i. l type stand of size 100x50x6mm channel with copper bound as per specification 15 g.i. cable support structure of size 65x65x6mm angle as per specification 16 90 lbs rail pieces for t / f ( 44.64kg / mtrs. ) 17 24 volt battery set 18 24 volt battery charger 19 11kv cable j / kit outdoor type for 3x300mm xlpe cable. 20 11kv cable j / kit indoor type for 3x300mm xlpe cable. 21 cable box o / d 33kv 3x300 xlpe 22 providing of armoured control cable4x2.5 mm sq. armoured control cable 23 2x2.5 mm sq. armoured control cable 24 earthing of substation outdoor equipment earthing ( earth mat ) ( m.s.round 32mm dia 4500 kgs ) 25 indoor equipment 26 fire fighting equipment of approved make4.5 kg co2 fire extinguisher portable type. 27 5 kg dry chemical power fire extinguisher portable type. 28 fire bucket stand with 6 nos. bucket 29 rubber mat 1mtrx2mtr thikness 20mm, 30 heat shrinkable outdoor type end termination cable jointing kit suitable for 11kv xlpe 3x185sq.mm. cable 31 heat shrinkable indoor type end termination cable jointing kit suitable for 11kv xlpe 3x185sq.mm. cable 32 g.i. channel 100x50x6 mm, 2400 mm long ( 9.56kg / mt ) with g.i.clamp of 65x8mm for dropper channel of 33kv line double pole / four pole 33 g.i.channel 100x50x6x2028mm ( 9.56kg / mt ) with 2 nos. g.i.clamp of 65x8mmfor dropper for fuse set & double pole 34 g.i. top channel 125x65x6 mm, 2240 mm long ( 13.10kg / mt ) with 2 nos. g.i.clamp of 65x8mm for s / s transformer double pole 35 copper l piece of size 400x50x6 mm for lt bushing rod of transformer 36 holding clamps for top channel tpmo & fuse set etc. with bolts & nuts 37 11kv tpmo ( as per specification ) 38 11kv fuse set 39 11 kv lightning arrestor 40 transformer earthing complete ( chemical pipe earthing as per specification ) 41 g.i. barbed wire 42 stay rod complete ( saty rod 16x1800mm, stay wire 5kg, stay clamp bolt & nut with grouting ) . 43 earthing of pole by ms earthing rod of 20x2500 mm. and 6 swg earthing wire etc. 44 al. crimping lugs 35 sq.mm. 45 al. crimping lugs 50 sq mm. 46 al. crimping lugs 70 sq.mm. 47 heat shrinkable jointing kit suitable for 11kv xlpe 3x35 sq.mm. cable sizeoutdoor termination kit 48 indoor termination kit 49 carriage of following material from pvvnl store 33kv vcb with double t / f control panel and ct 400 / 200 / 1a with structure.i ) 33kv vcbii ) control panel i / c for 33kv double t / fiii ) ct 400 / 200 / 1 1aiv ) steel structure 50 33kv pt ratio 33kv / 110v 51 11kv switchgear600 / 300 / 5a, 350mva, i / c 52 outgoing 200 / 100 / 5a 350mva 53 11kv bus couplar 350mva 54 11kv xlpe cable 3x300mm² 55 cable h.t.xlpe 33kv 3x300sq.m.m 56 acsr dog conductor for bay & jumpering. 57 11kv xlpe cable 3x185mm2 for feeders. 58 lt aluminium xlpe insulated cable of size 1x50 sq.mm. ( for ht jumpering ) 59 lt aluminium xlpe insulated armoured cable of size 3.5x70 sqmm. 60 11 kv aluminium xlpe cable 3x35 sq. mm. 61 stp sp 55 11m long 62 pcc poles, 9 m long 63 disc insulator polymeric type 70kn 64 disc fitting b&s type 70kn 65 11kv composite polymeric pin insulator. 66 erection of following material & miscellaneous electrical works.terminal gantry:fabrication with cutting, straightening & drilling of holes in joist / angle, fixing members of m.s.angle, by electric welding. 67 excavation of earth 2x ( 1.40x0.9x2.20 ) 68 erection of gantry in proper alignment, two pillers. 69 grouting in cc ratio 1:3:6, size 2x ( 1.40x0.9x2.20 ) +2x ( 1.40x0.75x0.30 ) 70 12mm thick plastering on plinth in ratio 1:4 of size 2x ( 1.40x0.30 ) x2+2x ( 0.75x0.30 ) x2+1x ( 1.40x0.75 ) x2 71 supply & fixing of stone pad 72 bus bar gantry:fabrication of bus bar gantry on m.s.rail 90lbs / 150x150mm r.s.joist including straightening, drilling of holes & fixing top droper and bracing of m.s.angle / channel, as per drawing. 73 excavation of earth 2x ( 0.75x0.75x1.20 ) x2 74 erection of bus bar gantry of m.s. rail 90lbs / 150x150mm r.s.joist in proper alignment. 75 grouting and making plinth in c.c. ratio 1:3:6 in size 2x ( 0.75x0.75x1.20 ) x2 + 2x ( 0.75x0.75x0.30 ) x2 76 12mm thick plastering on plinth in ratio 1:4 of size 4x ( 0.75x0.30 ) x4+2x ( 0.75x0.75 ) x2 77 supply & fixing of stone pad 78 line / bus isolator structure: ( 3nos. ) fabrication of structure, including cutting, straightening & drilling of holes in channel / angle. 79 excavation of earth 2x ( 1.10x0.60x1.0 ) x3 80 erection of line / bus isolator structure in proper alighment. 81 grouting of structure in c.c. ratio 1:4:8 in size 2x ( 1.10x0.60x1.00 ) x3 82 making plinth by c.c. ratio 1:3:6, in size 2x ( 1.10x0.60x0.30 ) x3 83 12mm thick plastering on plinth in ratio 1:4 of size 4x ( 1.10x0.30 ) x3+4x ( 0.60x0.30 ) x3+2x ( 1.10x0.60 ) x3 84 supply & fixing of stone pad. 85 fuse set / l.a. / p.t / post insulator structures ( 2+2+1+2 ) :fabrication of structure, including cutting, straightening & drilling of holes in channel / angle / joists. m.s.plate to be fixed on structure of required size. 86 excavation of earth in size 2x ( 0.90x0.50x1.00 ) x3+2x ( 0.45x0.45x1.00 ) x4 87 erection of above structure. 88 grouting by c.c. in ratio 1:4:8, 2x ( 0.90x0.50x1.00 ) x3+2x ( 0.45x0.45x1.00 ) x4 89 making plinth by c.c. ratio 1:3:6, in size 2x ( 0.90x0.45x0.30 ) x3+2x ( 0.45x0.45x0.30 ) x4 90 12mm thick plastering on plinth in ratio 1:4 of size 6x ( 0.90x0.30 ) x2+6x ( 0.50x0.30 ) x2+2x ( 0.90x0.50 ) x3+2x ( 0.45x0.30 ) x8 + 2x ( 0.45x0.30 ) x8+2x ( 0.45x0.45 ) x4 91 supply & fixing of stone pad. 92 plinth for 10 mva transformerconstruction of plinth for 10 mva, 33 / 11 kv transformer of ( 3.46x3.46x1.0 ) m ( 0.50m below ground level and 0.5 m above ground level ) as per details & drawing attached ( all required matrials provided / supply by the contractor own his cost ) : excavation of earth in foundation. 93 cement concrete in foundation in ratio 1:6:12, cement, sand & brick ballast. 94 first class brick work in ratio 1:4 with cement & coarse sand mortar. 95 cement concreting inner side of plinth in ratio 1:4:8, cement, coarse sand and stone shingle. 96 m.s.work for re inforcement 12mm. tor at a distance of 15cms. apart, including cutting, bending & binding by wire to each other for making jal in two layer, 12 to 15cms. apart. m.s.12mm tor bar provided by the contractor his own cost. 97 fixing of 4mtr.long, 2no. rail pices, 90lbs, on top of plinth at proper distance in alignment by c.c. 98 cement concrete in ratio 1:2:4, cement, coarse sand & stone shingle, on top of the plinth, including fixing of m.s.tor jal. 99 12mm.thick cement plaster in ratio 1:4, cement & sand mortar, on all side of plinth. 100 neat cement coating 3mm.thick on top surface of plinth. 101 plinth for 33 kv v.c.b.construction of plinth for the structure of 33 kv vcb & c.t.’s as per details for 02 no. ( all required materials provided / supply by the contractor own his cost ) : excavation of earth of size 2x ( 2.0x2.0x1.0 ) m pits for construction of plinth. 102 brick ballast ratio ( 1:4:8 ) ( cement, sand & brick ballast ) for foundation work 2x ( 2.0x2.0x0.5 ) m plinth. 103 r.c.c. work in ratio 1:2:4 ( cement, coarse sand & stone grit ) of 20m size for making plinth of size 2x ( 2.0x2.0x1.0 ) m and grouting of foundation bolts 04 nos. for 33 kv vcb. 104 12mm thick plaster with cement mortar in ratio 1:4 ( cement & fine sand ) of plinth of 0.4m upper side 105 earthing of outdoor equipments in switchyard, details as given below: digging of trench of size 0.50x0.75x330m., for laying of earth mat throughout in switchyard and re filling &ramming of the same earth in the to the trenches after completion of earth mat work. 106 laying of 32mm.dia m.s.bar in trench, properly in alignment along the length and width in switchyard. 107 cutting of 32mm.dia m.s.bar 3m.long and making one end in conical shape, by forging process and driving it into the earth, in trench at fixed distance as per drawing and properly welding with m.s.bar earthmat. 108 proper continuous electric welding of overlap joints of m.s.bar upto a length of 150mm. on both sides, along the length of m.s.bar and an extra piece of 12mm m.s.round 150mm.long, providing on both sides of overlap joints and continuous electric welding on both side, along the length of m.s.bar. all joints shall be painted with black bituminous paint. 109 proper electric welding at x joints of m.s.bar and welding by providing 25x6mm.”u” type clamp of m.s.flat, and proper continuous electric welding with m.s.electrode and m.s.bar at each x joints. all joints shall be painted with black bituminous paint. 110 providing & laying of g.i.strip of size 40x6mm for connecting the earthmat with each equipment ( terminal gantry, bus gantry, bus isolators, line isolator, 33kv c.t., 33kv v.c.b., l.as., fuse set, post insulators, t / f body & its neutral and m.s.frame of cable supporting structure ) , various steel structures. the work also includes cutting, bendidng, straightening, over laping and welding the earth strip with earth mat and by using high quality arc welding in already digged trenches. 111 painting of earth strip of size ( 50x6 ) mm with one coat of ready mixed primer with two coats of isi mark synthetic channel green paint. 112 earthing of indoor equipment, details as given below: cutting of 32mm.dia m.s. bar 3mtr.long and making one end in conical shape by forging process and driving it into the earth at each corner of bridge outside control room and proper welding with m.s.bars. 113 digging of pits for making bridge on both side of control room by laying 32mm. dia m.s.round in rectangular shape. electric welding on cross joints by providing “u” clamp in size 25x6mm. of m.s.flat and inter connecting both by m.s.round 32mm.dia through control room trench, with over lap joint by providing m.s.round 12mm dia, on both sides of over lap joints of m.s.round, by electric welding. all joints shall be painted with black bituminious paint. 114 water level earthing by boring and lowering of g.i. pipe size 40 mm dia & thickness 3mm into the ground at 20 mtr depth or upto the water level with the lower end of solid copper cone approx 225 mm long and 750 gm in weight shall be provided and screwed in pipe as well as bringing out a continuous copper wire 6 swg from the cone up to the ground surface where it will be bolted to the g.i. earth strip for transformer neutral connection, the g.i.earth strip size 50x6mm will be welded to the g.i. pipe and neutral earthing support & other installed equipment in switchyard. all required material provided / supply by the contractor own his cost. 115 construction of control cable trench in switchyard, as per details ( length 40mtr. ) :excavation of earth in size 0.750x0.40m. 116 c.c.work in foundation in ratio 1:4:8 ( cement, sand & brick ballast ) with proper ramming in size 0.750x0.15m. 117 ist class brick work in cement mortar in ratio 1:4 in size 0.23x0.35m. 118 25mm thick c.c. in floor of cable trench in ratio 1:2:4 ( cement, coursend and stone grift ) 20mm guage in size 0.3m width. 119 providing & grouting of m.s.strip of size 450x25x6mm in cable trench 100mm above floor level and at equal space distance 300mm 120 providing & grouting of m.s.angle iron of size 50x50x6mm in upper edge of trench. 121 c.c.work on the top in the ratio 1:2:4 in the grouting of edge of the trenches. 2x ( 40x0.23x0.06 ) 122 plastering of trench in cement, mortar in ratio 1:4, 12mm thick in cable trench. 123 fabrication and fixing cable trench cover of m.s.angle iron size 50x50x6mm of size 0.3m wide 0.5 to 1.0 mtr length with proper welding of 8mm size of bar 2nos. in length and 6nos. in width. work will be include providing of all required civil material & all fabrication material ( m.s.angle 50x50x6mm ) 0.5 mtr long 124 1.00 mtr long 125 removal of existing 10mva transformer and other accessories equipments.disconnecting ht cable connection from 33kv side &11kv side of 10mva power transformer for removing power transformer from plinth after proper shutdown. dismantling of 11kv cable support structure, copper bus bar structure, m.s.frame etc. 126 disconnecting copper flexible / earthing strip from power transformer neutral & dismantling neutral earthing systemto facilitate removal of power transformer from plinth. 127 disconnecting earthing strip from body of 10mva power transformer. 128 draining of transformer oil from conservator, radiators of existing 10 mva t / f, at 33 / 11 kv s / s pahasu, bsr into the dry & clean drums and stacking at the safe place in substation outside of switchyard. empty drums shall be provided bycontractor 129 removal of conservator, radiators and other accessories from existing 10 mva power transformer. 130 safe shifting of 10 mva power transformer main body and other accessories from the substation switchyard to outside the switchyard at new constructedplinth ofnew switchyard. 131 re assembling of conservator, radiators and other accessories to existing 10 mva power transformer. 132 re filling the transformer oil ( old & used in existing 10mva t / f ) 133 fabrication and erection of neutral earthing l type support made of g.i. channel size 100x50mm. structure shall be 4 mtr. long with 1 mtr. arms.structure shall be grouted in ratio 1:3:6 in block size 300x300x700mm and painted of welding joint with one coat of ready mixed primer and two coat of enamel aluminium paint work includes connecting neutral bushing rod of power transformer and g.i. earthing strip with the help of flexible copper bond, g.i. bolt and washer. 134 fabrication and erection of cable support made of two pieces of g.i. angle ( 65x65x6 ) mm, 2.75 meter long, joined to each other by means of 5 nos. g.i. flat ( 50x6 ) mm pieces of size 750 mm long each by welding at equal intervals and grouting in a block of size ( 300x300x700 ) mm in c.c. 1:3:6 ( cement, coarse sand and stone ballast ) complete and painted of welding joint with one coat of ready mixed primer and two coat of enamel aluminium paint. work includes providing of three nos. g.i. clamps made of ( 50x6 ) mm g.i. flat for holding the cable including nuts and bolts. 135 fabrication and grouting of g.i. frames 3.60 mt. long for support of copper bus bar. bus bar will be provided in l.v. side of power transformer. the g.i. frame shall be made of g.i. channel ( 100x50 ) mm in ‘t’ shape. providing 2 nos. support of g.i. angle iron ( 50x50x6 ) mm, 0.60mt. long below the top channel, drilling of 3 nos. hole on the top channel for fixing of 11 kv pin insulator and painted of welding joint with one coat of ready mixed primer and two coat of enamel aluminium paint and grouting the frame in c.c. ratio 1:3:6 ( cement, coarse sand and stone ballast ) in a block of size ( 300x300x700 ) mm. the work also includes the fixing of 3 nos. 11 kv pin insulator with pin and binding the copper bus bar with the pin insulator by aluminium binding wire in complete. 136 providing & fabrication of copper bus bar of size ( 2500x50x6 ) mm in l.v. side of 10mva 33 / 11 kv, power transformer, work includes connection of outside bus bar in l.v. side busing rod of power transformer and other side with outdoor 11 kv cable box as well as providing empire tape and h.t. tape etc. for proper insulation work. 137 installation of 11 kv switchgears in control room carefully & safely shifting of 11 kv switchgear panels from outside to inside the switch gear room grouting foundation of bolts in c.c. ratio of 1:2:4 ( including cutting of rcc floor and finishing of rcc floor ) as per requirement placing, aligning and fixing of 11 kv anchor gi bolts and nuts of proper size for completion of work in all respect. 138 safely mounting of 11 kv pt on 11 kv incoming switch gear filling of oil ( if required ) making all electrical connections and testing & commissioning of work. 139 proper fixing and making bus bar connection in between two switch gears after proper cleaning. work also include proper insulation, taping by empire, pvc and h.t. tape etc. 140 earthing of 11 kv switch gears:earthing of 11kv switchgears by means of g.i. earth strips ( 50x6 ) mm connecting to 4 nos. earthing electrodes of 32 mm dia. ( including fabrications of earthing electrodes ) 3m long on either side ( as per respo drg. res 40 ) .welding of g.i.earth strips ( 50x6 ) mm and also laying of the m.s.round 32mm dia in trench of control room and connecting to both sides squares including cost of g.i. earth strip ( 50x6 ) mm approx. 40m length and earthing of all indoor equipment by laying and providing g.i.earth strip ( 50x6 ) mm including cutting & welding etc. 141 h.t. power cable laying: laying 11 kv, ( 3x300 ) mm2 xlpe, cable from power transformer to 11 kv incoming switch gear in the cable trench 0.45 m wide, 0.90m depth. providing 150 mm local sand for cushion beneath and 150 mm above the cable ( quality of local sand required 0.375 cum / m in length ) . the cable shall be dully protected by brick. on both side of cable by laying brick vertically and bricks would also be laid bricks along the single cable ( minimum 18 nos. of bricks are to be laid top and outer side along the single cable. the work includes digging of trenches, laying of cable in under ground trenches, joining of terminal’s, back filling of earth and testing and commissioning of power cable etc. spare cable shall be left over and laid in the trenches in shape of 6 m ring at both ends. 142 laying and dressing of 11 kv 3x300 mm2 power cable in air / trench. 143 laying 11 kv, 3x185mm2 xlpe, power cable from outgoing switch gear to 11 kv double poles in the cable trench 0.50m wide, 0.90m depth. providing 150 thickness mm local sand for cushion beneath and 150mm above the cable ( quantity of local sand required 0.375 cubm / m in length ) . the cable shall be duly protected by brick. on both side of cable by laying bricks vertically and bricks would also be laid horizontally on top of vertically laid bricks along the single cable ( minimum 18 nos. of bricks are to be laid top and outer side along the single cable. the work includes digging of trenches, laying of cable in under ground trenches, joining of terminal’s, back filling of earth and testing and commissioning of power cables etc. spare cable shall be left over and laid in the trenches in shape of 6m rings at both ends. at the end of feeder cables, where the cable is to be laid across pucca / main road, 100 mm dia g.i. pipe will be weared over the cable in the cable trench for the protection of cable. 144 laying and dressing of 11kv 3x185mm² power cable in air. 145 supply and filling of sand in cable trench in the switch gear room. 146 preparation of 11 kv power cable ends:making of 11 kv xlpe heat shrinkable outdoor jointing kits 3x185sq.mm / 3x300sq.mm after duly plumbing and taping of cable, providing, fixing and crimping of proper size good quality lugs 147 making of 11 kv xlpe heat shrinkable indoor jointing kits 3x185sq.mm / 3x300sq.mm in switch gears after carefully removing the insulation of cable, providing and crimping of proper size of lugs, plumbing and taping of cable with good quality available insulation tape with j / kit boxes, fixing and insulating of lugs on cable with switch gear complete in all respect. 148 installation of 24v battery and battery charger:assembling and installation of the cabinet of 24v battery and battery charger in switch gear control room including grouting of foundation bolts as per drawing of manufacture, including providing the foundation nuts and bolts of proper size. the electrical connection between battery and battery charge with flexible copper lead of size 7 / 20 swg shall be done properly. the work includes installation, wiring upto control panel, testing and commissioning complete in all respect. 149 laying of different size of ( 2x2.5 ) mm2 / ( 4x2.5 ) mm2control cables i.e. from buchholz realy to marshalling box marshalling box to indication protection board in switch gear room, 33 kv ct’s to ct’s junction box, 33 kv ct, 33 kv pt, v.c.b. control panel junction box to 33 kv vcb control panel and control panel to 33 kv vcb outdoor operating mechanism panel from t / f etc. in the cable trench including making proper connection at buchholz relay, marshalling box and indication board as per required for installed equipment. 150 erection of 11 kv feeder double poles:erection and grouting of 2 nos. stp 55 11mtr long for making dp structure including fabrication fixing of g.i. channel, g.i.angle, tpmo, fuse set, disc, insulators, pin insulators no. plate, danger board, barbed wire ( 02 kg per pole ) etc. the work includes supply and fixing of necessary clamps size 75x10mm with g.i.nuts bolt & washer, bolts and washers. the work also includes grouting of double pole support in c.c. 1:3:6 ( cement, core sand & stone ballast ) in block of size ( 0.45m x 0.45 x 1 / 6 length of the pole ) including earthing of double pole with g.i. earthing rod complete in all respect. 151 erection and grouting of 2 nos. pcc 9.0mtr long for making dp structure including fabrication fixing of g.i. channel, g.i. angle, tpmo, fuse set, pin insulators no. plate, danger board, barbed wire ( 01 kg per pole ) etc. the work includes supply and fixing of necessary clamps with nuts, bolts and washers. the work also includes grouting of double pole support in c.c. 1:3:6 ( cement, sand & stone ballast ) in block of size ( 0.45m x 0.45 x 1 / 6 length of the pole ) including earthing of double pole with g.i. earthing rod complete in all respect. 152 providing & wearing of 110 mm dia 3.5 mm long g.i. pipe in the feeder cable of size of ( 3x185 / 3x300 ) mm2 xlpe 11kv power cable before making the outdoor cable boxes. the work includes the sealing of g.i. pipe, top end and lower end of the pipe is to be buried in to the ground about ½ m and proper dressing of cable etc. the work includes lifting, mounting and clamping of 11 kv feeder cable boxes on the feeder with double pole structure and making connections including supply of cable mounting clamps etc. 153 erection of acsr dog conductor for jumpering on double pole 154 providing & fixing of smc danger board at each location as per specification of the drawing. size 200mmx250mm & 3mm thickness with g.i.clamp & nut & bolt 155 grouting of stay rods ( 16x1800 ) mm including all work of excavation, cement concrete in size ( 0.60x0.60x0.30 ) m in ratio 1:3:6 cement, sand, 20mm stone grift ) as per drg. including back filling of soil and proper ramming etc. 156 fixing, tightening & nozzling of stay wire with stay rod with the poles of required tension as per drawing, including providing & fixing of stay insulators of 11kv and stay clamps. 157 painting of structurespainting of the following structure with one coat of ready mixed primer and two coats of isi mark aluminium paint after rubbing with sand paper to the surface of the structure including labour and t&p complete in all respect.double pole. 158 all welding joint of g.i.steel structure. 159 installation & mounting of 11kv / 0.433kv, 3 phase, existing 25kva, distribution transformer on 9 mtr pcc double pole and fittings. work complete in all respect. 160 installation of 33 kv isolators:assembling and installation of line / bus isolator on the isolator structure. adjusting of operating mechanism in proper alignment so as to ensure smooth operation of the same. in case of line isolator proper operation of earth links shall also be ensured. the work includes fabrication for proper fixing if required. 161 installation of 33 kv lightning arrestors: assembling and installation / mounting of 3 nos. lighting arrestors on the l.a.’s structure / terminal gentry, complete with earthing and line connections. the work includes fabrication for proper fixing, if required. 162 installation of 33 kv post insulators:installation of 3 nos. pi on structure. the work includes fabrication for proper fixing, if required. 163 installation of 33 kv fuse set:assembling and installation of fuse set on the fuse set structure. the work includes fabrication for proper fixing, if required. 164 installation of 33 kv vcbassembling and installation of 33 kv vcb on the vcb out door structure on the plinth. adjustment of operating mechanism in proper alignment for smooth operation of the same. the work also includes fabrication of addition arrangement for proper fixing, if required. 165 installation of 33 kv vcb control panel for single feeder & double t / f control panel.carefully and safely shifting of 33 kv vcb control panel from outside of the switch gear room to inside of the switch gear room, grouting with anchor bolts in the floor, work also includes cutting & proper finishing of floor if necessary for completion of work. placing and fixing of panel on foundation, bolts of proper size in proper position and alignment. 166 installation of 33 kv c.t.’s:installation of 3 nos. c.t.’s on the c.t’s structure. the work includes fabrication for proper fixing, if required to complete the work. 167 installation of 33 kv p.t.’s:installation of 3 nos. p.t.’s on the p.t’s structure. the work includes fabrication for proper fixing, if required to complete the work. 168 33 kv ct’s junction box:providing & fixing of junction box of size ( 400x400x150 ) mm made of g.i. sheet of 16 swg in between 33 kv ct’s & control panel. the work also include making proper connection on the junction box and making all connection in between ct’s and control panel complete as per manufacture’s panel drawing including testing and commissioning of work etc. complete the work. 169 33 kv bus bar jumpering:jumpering, including clamping / binding with acsr panther conductor / 33kv 3x300mm2 xlpe cable with providing p.g.clamp & other accessories.terminal gantry to 33kv p.t 170 33kv p.t to 33 kv p.i 171 33 kv p.i to 33kv l.a 172 33 kv l.a to 33 kv line isolator 173 33 kv line isolator to 33 kv vcb 174 33 kv vcb to 33 kv c.t 175 33 kv c.t to 33 kv p.i 176 33 kv post insulator to bus isolator. 177 33kv bus isolator to 33kv vcb 178 33kv vcb to 33kv ct 179 33kv ct to 33kv fuse set 180 33kv fuse set to 33kv l.a 181 33kv la to 33 / 11kv 10mva t / f 182 lighting arrangement of 33 / 11 kv s / s outdoor switch yard and its area:supply & installation and erection of 6 mtr. long street light supports with 2.4 feet long street light brackets including fixing and supply of junctions box, street light support shall be made and fabricated from g.i. pipe of 3.0 mtr. long 100mm dia. and 3.0 mtr. long 75mm dia with 2.4 mtr. long street light bracket in arc shape and made up of 40 mm dia g.i. pipe.grouting of support in c.c. ratio 1:3:6 ( cement, core sand and stone ballast ) in size ( 0.40x0.4x1.2 ) m, lightning poles shall also be earthed by connecting to earth mat. 183 supply and fixing of led light 120 w and of standard quality isi mark with water tight elbow fitting etc. complete in all respect and suitable for above street light supports ( acceptable make philips, bajaj, heawels or siska ) . 184 laying of 3½x70 mm2 pvc lt cable from 11 / 0.4 kv, 25 kva t / f to l.t. distribution board in switch gear room after digging trench for laying cable and refilling of trench including connections at both ends after providing and crimping of lugs of proper size for completion of work and laying brick over & both sides of l.t. cable after digging trench of 0.3 m wide & 0.5 m depth and providing and wearing 75 mm dia g.i. pipe of 2.5 m length over l.t. cable complete in all respect. 185 laying of 3x50mm2 11kv cable from 11kv outgoing vcb in control room to pcc double pole after digging trench for laying cable and refilling of trench including connections at both ends after providing and crimping of lugs of proper size for completion of work and laying brick over & both sides of 11kv cable after digging trench of 0.3 m wide & 0.5 m depth and providing and wearing 75 mm dia g.i. pipe of 2.5 m length over 11kv cable complete in all respect. 186 erection of l.t.aluminum xlpe insulated cable 1x50mm2 for jumpering ondouble pole. 187 providing and lightning arrangement of 33 / 11kv s / s control room ( 8 no. ceiling fans of preferable make havels, crompton & bajaj ) , ( 20 no. 12 watt led bulb with fitting if required preferable make philips, crompton, havels & bajaj ) 188 providing & fabrication of l.t. distribution board by using g.i. angle size ( 65x65x6 ) mm of size ( 2x0.75x1.4 ) m and grouting the stand in ground floor in switch gear room at proper place. 12 mm thick indian wooden ply with sunmica top will be fixed on the ply frame and frame will be painted by one coat of primer red oxide and two coats of smoke grey paint. 189 providing & fixing 100amp tpn mccb, 4 pole and 4 nos. 32amp single phase, mccb in box as per catalogue no. 607780 ligrant make or equivalent. 190 providing and laying ( 2x6 ) mm2 l.t. aluminium pvc cable from s.g. room to street light supports after digging of trench laying of ( 2x6 ) mm2 cable, providing brick on top of cable, refilling of trench, making connections of poles with street light fitting through junction box complete in all respect. 191 supply & fixing of aluminium clamps such as isolator, la, transformer end clamp, fuse set, post insulator, pg clamp etc. complete with nut, bolt & washer for dog / panther conductor 192 to provide required no. of technicians to work on power t / f, ht / lt panels & 33kv line during testing as assisting technical hands of test team during commissioning & energisation. 193 construction of sso’s approached road 1.2 mt wide in switch yard by laying dry brick ballast in 15 cm layer, 115 mm thick brick work 1:4 in both side of edge, providing 10 cm thick cc in ratio 1:2:4. the work include proper plastering top & side of road and making groove, leveling & dressing of earth beneath the brick work on edge. all required materials provived / supply by the contractor own his cost. 194 construction of fire protection wall size 5mtrx5mtr ( as per approved drawing ) . 195 digging of trench by excavation of earth of 1050x750mm size for 33kv line 196 safe laying of 33kv, 3x300sq.mm. xlpe cable in cable trench to respective double pole. 197 providing & laying of ist class bricks, along the length on both side of 33kv xlpe cable in cable trench ( minium 18no. bricks / mtr per cable ) and stone slab of size 450x600x50mm on top of the each cable, providing 150 thickness mm river sand for cushion beneath and 150mm above the cable as per specification. 198 back filling of excavated earth in the cable trench upto the ground level and ramming properly. 199 providing & fixing 150mm dia 2mm thick 3m long g.i.pipe over 33kv, 3x300sq.mm xlpe cable before mounting the 2no. cable on double pole. work includes fixing of clamp, sealing of top and bottom end of the g.i.pipe. one end of g.i.pipe is to be buried under earth about 500mm. 200 making of 33kv outdoor type cable end termination by heat shrinkable xlpe cable jointing kits and crimping with proper size aluminium lugs. work includes providing aluminum lugs, insulating tapes etc as per specifications. 201 dismentling of old 06 nos. 11kv vcb, 02 nos. 33kv vcb & transpotation topvvnl store...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39901863 tender for increasing capacity of following bangarmau grameen1x5+1x8 mva to 1x5+1x10 mva, ajgain1x10+2x5 mva to 1x5+2x10 mva, miyaganj 1x8+1x5 mva to 1x8+1x10 mva, hasanganj 1x8+1x5 mva to 1x8+1x10mva, pathakour 1x5 mva to 1x10 mva, bihar 1x5 mva to 1x10 mva, mawai 2x5 mva to 1x5+1x10 mva, gangaghat 1x5 mva to 1x10 mva, erabhetir2x5 mva to 1x5+1x10 mva, pd nagar 2x5 mva to 1x5+1x10 mva & industrial area 2x5 mva to 1x5+1x10 mva distt unnao 2 33 kv line isolator 3 33 kv lightening arrester 4 33 kv vcb 800 amp., 750 mva 5 33 kv ct 200 / 100 / 1 amp. 6 33 kv ct 400 / 200 / 1 amp. 7 11 kv vcb o / g ctr 200 / 100 / 5 amp, 350 mva 8 11 kv vcb bus coupler 9 11 kv 3x300 sq mm xlpe 10 11 kv 3x120 sq mm xlpe 11 ms angles 75x75x6mm 12 acsr panther conductor 13 pcc pole 8.5mtr long 14 st pole 11 mt long sp 55 15 11 kv v type cross arm 65x65x6 mm 16 polymeric 11 kv disc insulator b&s. type 70 kn. 17 disc fittingsdog / racoon 70 kn. 18 polymeric 33kv pin insulator 19 ms channel 125x65mm3.2 mtr. long 20 ms channel 100x50 mm 21 ms channel 100x50x2028 mm ( dropper for fuse set ) 22 ms channel 100x50x2240mm top channel 23 11 kv polymeric disc insulator t & c 24 11 kv disc fitting t & c type 4500 kg. 25 11 kv composite polymeric pin insulator 26 ms earthing rod 20x2500 mm 27 ms angle 65x65x6mm 2028 mm 28 guarding angle 65x65x6mm ( 2500 / 1600 ) mm 29 complete stay set ( gi stay rod 16x1800 mm ) 30 stay wire 7 / 10 swg ( 5 kg. / stay ) 31 11 kv 3x300 sq mm xlpe cable outdoor jointing kit 32 11 kv 3x300 sq mm xlpe cable indoor jointing kit 33 11 kv 3x120 sq mm xlpe cable outdoor jointing kit 34 11 kv 3x120 sq mm xlpe cable indoor jointing kit 35 gi wire 8 swg for guarding 36 gi wire 6 swg for earthing 37 acsr weasel conductor 38 single core pvc cable 1x240 sq.mm. 39 dismantling & safe shifting of existing old & non working 05 mva t / f from plinth to suitable storage place after opening jumper and cable connections as per required. 40 extension and repairing of existing power transformer plinth of 05 mva t / f as per required. 41 lightening arrestor, p.i. & ct structure : fabrication of lightening arrestor, p.i. & ct structure 3.5 mtr. in height as per drg. digging of two no pits of size 1.075x0.9x0.3 mtr. providing stone pad at the bottom of the pit and grouting of two legs of the structure in cc ( cement coarse sand and stone grit of 20mm gauge ) of the ratio 1:4:8 in block of 1.075x0.3 mtr. including all civil material, t&p complete in all respect. the work includes dragging, shifting up to 40 mtr., raising and erecting the two legs with runner on proper alignment and level and plumb. both plinths of the structure shall be properly finished with smoothing of edges. 42 plinth of vcb : construction of plinth of size 2.0 mtrx1.5mtrx0.9mtr. suitable for erection of upper structure of 33kv vcb including grouting of anchor bolts in proper alignment and level. scope of work includes excavation of foundation base and concreting in cc 1:3:6 ( cement, find sand & stone grit ) 1st class brick work in cement mortor ratio 1:4:8. 43 connection of 33 / 11kv 10 mva t / f at both side of ( ht / lt ) with proper & suitable connectors, lugs. this works also include jointing of earthing strip with body and neutral by proper welding and bolting. ( all decentralised materials are to be provided by contractor ) . 44 earthing for power t / fby way of boring and lowering of 40mm dia, 2.9 mm thick gi pipe b class from ground upto the water level ( minimum 60 feet deep ) as per standard practice as per respo / rec drg with making of earth pit of 300x300 mm & 1 feet deep with cover. ( all materials to be provided by contractor ) . 45 neutral standfabrication and grouting ( 1:4:8 ) of ms angle 75x75x6mm in l shape & in proper size and alignment to provide support through gi earthing strips ( 50x6 ) mm size for power transformer neutral including supply & fixing of flexible copper bonds for neutral earthing as per respo drg. ( all decentralised materials to be provided by contractor ) . 46 cable standfabrication and erection of cable support made of two pieces of ms channel 100x50mm, 3.0 mtr. long joined to each other by means of 5 no. ms flat 50x6mm pieces of size 150mm long each by welding at equal intervals as per drawing and grouting in block of size 300x300x700mm ( 1:4:8 ) complete. this includes providing of required ms clamp made of ms flat holding the cable including nuts & bolts and fixing of xlpe cable. 47 installation of isolators: assembling and installation of line / bus isolator on the isolator structure adjusting of opening mechanis in proper alignment so as to ensure smooth operation of the same. in case of line isolator proper operation of earth links shall also be ensured. the work includes fabrication & proper connection with earthmat / earthing by g.i. earth strip 50x6mm proper fixing if required ( all decentralised materials to be provided by contractor ) . 48 installation of p.i. & lightening arrestors : assembling, installation & mounting of 3 no. ( 1set ) l.a. & post insulator on the l.a & p.i. structure / complete with making earth connections ( separate ) with gi strip 50x6mm. the work includes fabrication for fixing if required. ( all decentralised materials to be provided by contractor ) . 49 installation of ct: installation of 3 no. ( 1 set ) ct on the ct structure along with ct junction box. the work includes fabrication, proper fixing of c.t. with making earth connections ( earth mat / earthing ) with gi strip 50x6mm and control wiring connection, proper commissioning & testing. ( all decentralised materials to be provided by contractor ) . 50 installation of vcb: installation of 33kv vcb complete work with making earth connections ( earth mat / earthing ) with gi strip 50x6mmincluding control wiring, commissioning & testing ( all decentralised materials to be provided by contractor ) . 51 installation of switchgears in control room:shifting carefully & installation safely 11kv i / c, o / g & bus couplar switchgears from outside the switchgear room placing and fixing of switchgear on foundation providing g.i. bolt & nuts of proper size in proper position and alignment. this includes checking, complete work with mounting of p.t. on incoming s / g with proper testing, connetion of earthing & commissioning of switchgears. 52 fixing and making bus bar connections in between all switchgears after cleaning and tapping with h.t. tape, empire tape and pvc tape properly, providing and fixing of 6 mm thick bakelite separators and plugging of all opening & holes with plastic compound complete work as per required. 53 earthing of 11 kv, 33 kv switchgears & equipment: earthing of 11 kv, 33 kv switchgears equpiment by lowaring and boring of chemical earthing outside of switchyard and connecting through g.i. strip 50x6mm with indoor / outdoor equipments with making of earth pit of 300x300 mm & 1 feet deep with cover. ( all the material provided by the contractor ) 54 painting of all structures and equipments with good quality isi mark one coat of red oxide primer & two coats of aluminium paint. 55 laying & dressing of 11kv 3x300 sq.mm xlpe cable from 10mva t / f to 11kv incoming switchgear by excavation of trench in the ground of size 450mm wide, 900mm deep providing 150mm fine sand cushion belowthe cable. the cable shall be duly protected by bricks, sand & stone slab and refilling & ramming of the left out soil. spare cable shall be left and buried in the trench in the shape of rings at both ends. cable laying work includes unrolling, cutting, making ring and sealing both ends of the cable. ( all decentralised materials to be provided by contractor ) . 56 laying & dressing of 11kv 3x120 sq.mm xlpe cable from11kv o / g switchgear by excavation of trench in the ground of size 450mm wide, 900 / 1200 mm deep providing 150mm fine sand cushion below & abovethe cable. the cable shall be duly protected by bricks, sand & stone slab and refilling & ramming of the left out soil. spare cable shall be left and buried in the trench in the shape of rings at both ends. cable laying work includes unrolling, cutting, making ring and sealing both ends of the cable. ( all decentralised materials to be provided by contractor ) . 57 hoisting of 11kv cable with 100 mm dia 3 mtr. long gi pipe on the feeder cable before mounting the cable on the double pole, lifting, mounting and clamping of 11kv feeder cable boxes on the feeder double pole structure and making connection including supply of cable mounting clamps. the work includes the sealing of gi pipes, lower end of the pipe is to be buried into the earth by about one foot. ( all decentralised materials to be provided by contractor ) . 58 connection of 11kv xlpe cable for 11 kv switchgears & 33 / 11kv t / f of requried size. 59 making vertical / horizontal jumper connections using panther / dog conductor with existing busbar gantry through pg clamps and connecting all equipments with each other through connecting clamps. the work includes all the jumpers from busbar tot / f ( 1no. t / f bay & all equipments ) ( all fitting clamps, pg connector etc. to be provided by contractor ) . 60 supply and laying of following size copper control cable through underground / cable trench / trenching sgr interlinking through proper connections to t / f control panel / protection board / battery and battery charger / bunch joints, relay 33 / 11kv t / f junction box / 33kv vcb, cts etc. as per site conditions: 61 4x2.5 sq.mm 62 6x2.5 sq.mm 63 fixing of single corepvc cable, 1x240 / 400 / 630 sq.mm. & fixing between transformer incoming 3x300 sq.mm xlpe cable and transformer 11 kv / lv side bushing connector for reducing of tension at lv side bushing. 64 construction of 11 kv feeders : ( a ) excavation of foundation pit in mix soil / normal soil, soft & hard rock and its back filling and levelling etc. the size of the pit will be 800x900 mm and having a depth of 1 / 6 of the full length of the support. erection of supports by providing stone pad, fixing all clamps and other accessories such as no. plate, danger board, barbed wire ( 2kg. ) , painting ( one coat red oxide primer & two coats of red& aluminium paint at required height ) . as per relevant respo / res. drawing . this includes any fabrication, if required. ( b ) grouting of above supports with cement, concrete ( cc will be of cement coarse sand & stone grit ) grouting will be done with the help of wooden / steel formers in a block of size 450 mm x 450 mm x 1 / 6 of the full length of the support in the cc 1:4:8 ratio as per respo / res. drawing including back filling and proper ramming. ( c ) making plinth of stp 300 mm, dia & 300 mm above ground level in cc of 1:4:8 & plastering of the same with 12 mm thick plaster of cement & sand in 1:4 ratio. ( d ) earthing of supports with earth electrode 2.5 mtr. length including excavation of pit and driving m.s. rod upto proper depth and connecting the earth electrode with the help of 6 / 8 swg g.i. wire and earthing lugs. respo / res. drawing. 65 double pole structure for outgoing feeder on 8.5 mtr pcc pole with complete accessories. 66 single support on 11mtr. stp : 67 single support on 8.5 mtr pcc pole : 68 ( a ) grouting of stay rods 1800x20 mm including all works of excavation grouting by, cement concrete in size 0.60x0.60x0.3 mtr. with ratio 1:4:8 as per relevant drawing including back filling of earth and proper ramming. ( b ) fixing, making of loop insulator, tightening & nuzzling of stay with the poles and required tension as per respo / res. drawing. 69 laying, spreading, lifting, stinging, jointing and final sagging of acsr dog / weasel conductor in accordance with profiles and sag chart including binding, jumpering and fixing of all accessories in 3 nos. conductor in parallel with pg clamp binding wire etc requested for job. 70 guarding between two poles like single / double / tri. / four poles etc. to guardlt / 11 kv / telephone lines, road / river crossing etc. with g.i. wire 6 swg and g.i. wire 8 swg including fixing of guarding channel of requested sitewith clamps and nuts and bolts as per respo / res. drawing 71 supply and installation of 24 volt battery and it charger with connections to existingcontrol circuit complete in all respects. 72 looping of branches of trees along the route of line and disposal of the same after obtaining permission of competant authority....

Purvanchal Vidyut Vitaran Nigam Limited - Uttar Pradesh

39901807 supply of decentralized material in edd meja prj , vkiwfrz dk fooj.ka , cross arm holding clamp with nut &bolt , f bracket of fitting top insulator with nuts &bolt , barbed wire gi , clamp with nuts &bolts for top channel , e breacket with bolt&nuts , pg clamps for dog , earth wire clamps for pcc pole , loop guard complete 3 phase , lt pvc cable 3.5x70/35 sq mm , 11 kv ‘v’ typecross arm 100x50x6 mm , f bracket for 33 kv line , 33 kv pin with nuts , aluminimum paint , red oxide paint , al pg clamps weasel to weasel , al pg clamps dog to dog , stone pad 300x300x75 , gst extra as legally applicable...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39900993 tender for capacity increase / installation of approved transformers and related work at various places in the additional business plan year 2023 24 under electricity distribution division iii ( karnailganj ) , gonda area. 1 all these below items / materials at s.n. 1.01 to 1.16 will be given and errected by the contractor on his own cost. 2 clamp for top, dropper and t off etc. 3 stone pad 4 f bracket 5 barbed wire 6 d.b. box clamp 7 d.b. box 8 pearcing clamp 9 danzer board 10 alluminum lug 400 sqmm 11 alluminum lug 120 sqmm 12 lt clamp 13 suspension clamp 14 dead end clamp 15 m.s. nut and bolt 16 i hook with clamp 17 v type x arm holding clamp 18 loading, unloading and safe cartage of the following materials ( s.n. 2.01 to 2.30 ) from electricity store centre, gonda to the work site / dump site ( distance up to 60 km ) 19 st poles ( 11 mtr. long ) 20 pcc poles ( 8.5 mtr long ) 21 400 kva transformer 22 250 kva transformer 23 100 kva transformer 24 63 kva transformer 25 25 kva transformer 26 other line materials 27 lt abc cable 3.5x25 sqmm 28 abc cable 3x50 sqmm 29 abc cable 3x95 sqmm 30 lt cable 3.5x150 sqmm xlpe 31 lt cable 1x400 sqmm xlpe 32 lt cable 3.5x70 sqmm xlpe 33 acsr weasel conductor 34 cross basing angle 35 copper l piece 50x50x6 mm 36 11 kv v type x arm 37 top channel 38 droper channel 39 sub station base 40 11 kv pin insulater 41 11 kv pin with nut 42 disc insulater 43 disc fitting 44 earthing complete with 20 mm rod 45 stay set complete 46 stay wire 47 earthing off t off with material 48 bush set 49 erection of single st poles ( 11 mtr long ) for 11 kv / l.t. line alongwith fitting of all accessories on pole including dragging of pole from dump site to pit site 50 erection of single pcc poles ( 8.5 mtr long ) for 11 kv / l.t. line alongwith fitting of all accessories on pole including dragging of pole from dump site to pit site 51 erection of sectional double pole sectional pcc pole ( 8.5 mtr long pcc pole ) alongwith fitting of all accessories on pole including dragging of pole from dump site to pit site. 52 earthing of pole. 53 erection and grouting of stay sets alongwith complete fittings. cement, sand & brick ballast provided by the contractor at his own cost. 54 grouting of poles with 1:4:8cc ratio of cement, sand & brick ballast, backfilling of pits with mud completely.all required materials provided by the contractor at his own cost. 55 laying, sagging, stringing and binding of ab cable upto proper sag of following size 56 lt abc cable 3.5x25 sqmm 57 abc cable 3x50 sqmm 58 abc cable 3x95 sqmm 59 laying, sagging, stringing and binding of following size, where is required as per estimate ( u.g. / o.h. ) 60 lt cable 3.5x150 sqmm xlpe 61 lt cable 1x400 sqmm xlpe 62 lt cable 3.5x70 sqmm xlpe 63 laying, stringing, sagging & binding of conductors of 11 kv in 3 phase, 3 wire line with jumpering ( where as required ) 64 construction of 11 / 0.4 kv s / s for following capacity of t / f with mounting and fitting of t / f on plinth / double pole with proper fitting of all acessories and connecting with all circuit including earthing of t / f fitting with all accessories. 65 400 kva transformer 66 250 kva transformer 67 100 kva transformer 68 63 kva transformer 69 25 kva transformer 70 dismounting of following capacity t / f and loading, unloading and safe cartage of the following materials from the work site / dump site to electricity store centre, gonda ( distance up to 60 km ) 71 250 kva transformer 72 100 kva transformer 73 63 kva transformer 74 25 kva transformer 75 16 / 10 kva transformer 76 construction of plinth with fencing as per resspo norms / estimates. ( all the material required for work shall be provided by the contractor on his own cost ) ...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39900078 increasing capacity ( 250 to 400 kva ) of 01 no. transformer at pahadpur near gudamba thana in the work area of sub division engineering college under jurisdiction of edd rahim nagar, lesa, trans gomti, lucknow in the head ofadditional business plan 2023 24 1 loading, carriage & unloading of following materials from centre store daliganj to work site and its stacking. distance approx ( 0 35 ) kms. 2 line material 3 stp pole 9 / 11 mtr. long. 4 250 / 400 kva t / f 5 lt pvc cable 1x400 / 3.5x 240 / 1x 70sqmm 6 abc ( 3x120 / 95 / 70 / 25 / 16 ) sqmm. 7 11 kv xlpe cable ( 3x35 / 70 / 120 / 170 / 185 ) 8 11 kv cable jointing kit o / d ( 3*70 / 120 / 185 ) sq mm 9 fabrication, erection of sub station type double pole on 8.5 mtr long pcc / 11 mtr. long st pole along with fixing of necessary clamps. accessories required including supply & fixing of straight ms 100x50mm top channel ( 2240mm long ) one no. dropper channel / angle 100x50 mm 2 nos. with arrangement of fixing 3 nos. pin insulator as per respo specification and direction of e / i. only pole & insulator supplied by the deppt. 10 construction of t / f plinth of size 2x2x1.2 meters with help of 1st class bricks and massonary in the ratio 1:4 cement & sand coarse, filling the structure completely as per norms with rcc top 1:2:2 cement, sand coarse, stone grit with ms bar and ms channel for resting t / f. all material shall be arranged by the contractor. 11 wiremessfencing of 11 / 0.4 kvs / s shall be made of rectangular of size as per site requirement not exceeding 3 meter fabrication 45x45x5 mm angle the frame is also have 1 no. horizontal runner of ms flat 40x5 welded in middle to support of wire mess. rectangular welded type wire mess of size 50x25 made of 12 s.w.g. wire mess shall be welded all along the periphery of theframe as well as on horizontal runner to give extra strength of welding to wire mess welded on the frame. diagonal bracing of all the frame panel will be welded with ms flat of size 25x3mm to support as per respo specification & direction of e / i. 12 construction of masonry type distribution pillar box with first class brick ballast cement, coarse sand, local sand, brick ballast and ms round bar of 10 mm dia including supply and mounting of 02 nos. straight ms angle 50x50x6x750 mm 2 nos., henely type tailless fuse units 500 amps. 650 volts one no. for incoming and other for outgoing, copper bus bar 4 nos. 1000x50x6 mm with locking arrangement made of 18 swg bp sheet. 13 providing and fixing of 11 kv do fuse set along with clamps & nut bolts on existing of double pole. 14 providing and fixing of 11 kv tpmo along with clamps & nut bolts on existing of double pole. 15 ordinary earthing by ms earth rod 2500mm long as per respo schedule. only gi wire& earth rod shall be supplied by the department. 16 erection & commissioning of ( 3x120 / 95 / 70 / 25 / 16 sq.mm ) aerial bunched conductor. 17 laying oflt pvc cable 1x400 / 3.5x240 sqmmas respo specification & direction of e / i. 18 earthing of t / f pipe type with 60 fit deep borring and providing gi pipe 1.5 dia ( 60 fit gi pipe ) and gi strip 25x5 mmx6 meter long attached with clamps, l piece, nut & bolts and gi pipe cap. all material shall be supplied by the contractor. 19 safe installation of 250 / 400 kva t / fon double pole / plinth by providing and fixing of all accessories along with making ht / lt connection and its commissioning. 20 dismantling of 250 kva t / f on exsiting plinth along with dragging, loading cartage and unloading to work site j.e dump store / central store. 21 supply and fixing 22 aluminium lug 400 sq mm 23 lt clamp with i hook 24 lt bearer connector 25 lt connector b type 26 denger board wityth clamp 27 dead clamp 28 number plate 29 barbed wire 30 suspension clamp 31 copper l piece 32 gst will be paid extra as per rule....

Village Panchayat - Uttar Pradesh

39899449 tender for provide of construction material cement, balu, sand, bajri, brick, blast, interlocking tiles, wall tiles, fursh tiles, rod, iron jali, soil, wall painting, sanitary equipment, electric equipment, iron fencing wire, iron angle, furniture bench, cement concrete bench, dustbin, street led light, barbed wire, paint, primer, toilet sheet, handpump repairing equipment, rcc pillar, pvc pipe, water storage tank, ply board, running water supply equipment, iron gate, iron sheet, roof sheet, mike sheet....

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39898999 tender for execution of various work for shifting of line under the head full deposit under pmgsy in edd first under edc shahjahanpur. 1 safe carriage including loading / unloading & proper stacking of following store materials from store centre to site of work ( approx. distance 0 50 km. ) 2 s.t pole 11 mtr long 3 pcc pole 8.5 mtr long 4 top channel 11 kv 5 33 kv pin insulator 6 stay complete 7 earthing complete 8 earth wire complete with nut bolt 9 11 kv disc insulator 10 11 kv disc fitting 11 11 kv pin insulator 12 11 kv pin with nut 13 f clamp 14 11 kv x armholding clamp 15 11 kvv type x arm 16 m.s. t off channel 17 cable lt abc ( 3*50+1*35+1*16 ) sq. mm 18 acsr weasel conductor 19 errection work 20 fabrication, erection of single pole for 11 kv line on stp 11 mtr long pole with fixing of necessary clamps & other accessories like 1 no. 11kv v type cross arm, 1 no. f clamp. itsgroutinginratio1:4:8, plinthing300mmaboveground level, painting of pole with one coat of red oxide & two coats ofenamelpaint ( isimark ) &earthingofsupportasper ressponorms ( allgrouting&paintingmaterialshallbeprovided by the contractor. ) . 21 fabrication, erection of single pole for 11 kv line on pcc pole 8.50 mtr long pole with fixing of necessary clamps & other accessories like 1 no. 11kv v type cross arm, 1 no. f clamp. itsgroutinginratio1:4:8, plinthing300mmaboveground level, painting of pole with one coat of red oxide & two coats ofenamelpaint ( isimark ) &earthingofsupportasper ressponorms ( allgrouting&paintingmaterialshallbeprovided by the contractor. ) . 22 fabrication, erection of single pole for lt line on stp 11 mtr long pole with fixing of necessary clamps & other accessories like l.t. clamp, earth wire clamp etc. grouting in ratio 1:4:8, plinthing300mmabovegroundlevel, paintingofpolewith one coat of red oxide & two coats of enamel paint ( isi mark ) & earthing of support as per resspo norms ( all grouting & painting material shall be provided by the contractor. ) . 23 erection / fixingforstaysetwithstaywireandclampasper resspo drawing including binding. climbing, clamping, tightening and nozzeling etc. complete in all respect including its grouting in ratio 1:4:8 before back filling of the pits as per resspo, cement, brick, concrete ballast, sand and etc would beprovidedbythecontractorfor33 / 11kvsinglesupport, double pole and four pole structure. 24 stringingandsaggingof11kvoverheadlineonacsr weasel conductor as per resspo norms. 25 febrication work of x arm clamps vareios channel etc as per require ment for works completion ( nos ) 26 installation of v type cross arm , guardingangle & clamps etc. 27 recd. back of11kv line lenth appox. 2200 ckt mtr. 28 fixing of danger board and g.i barbed wire on each pole including proper clamping. ( all material would be provided by contractor ) . 29 painting ofst poles of the 33kv / 11 kv line with one coat of red oxide primer and two coats of aluminium white paint of isi mark and top danger portion of each support must be painted by providing two coat of post office red paint ( 1.5mtr upper portion of support. ) paint and material would be given by contractor to complete of work at his own cost....

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39898938 increasing capacity of 33 / 11 kv substation pakwara ( 10+5 to 2x10mva ) , choudharpur industrial ( 10+5 to 2x10mva ) , naanpur ( 2x5 to 10+5mva ) , kundarki ( 5+10 to 2x10mva ) , pipalsana ( 3x5 to 2x5+10mva ) , thakurdwara dehar ( 5+10 to 2x10mva ) , surjannagar ( 5+10 to 2x10mva ) and 33 / 11kv s / s ramganga vihar ii ( 2x5 to 10+5mva ) , district moradabad. 1 supply of following items : (by contractor)for item no. 1.01 to 1.261.01 33 kv bus isolator 800 amp/line isolator 2 33 kv fuse set 3 33 kv lightening arrestor 4 33kv post insualtor 5 structure 33 kv ct on 125x65x6 mm galvanised channel(as per respo norms) 6 2x2.5 mm2 control cable 7 4x2.5 mm2 control cable 8 11 kv 3×300mm2 xlpe cable jointing kit (outdoor) 9 11 kv 3×300mm2 xlpe cable jointing kit (indoor) 10 11 kv 3×185mm2 xlpe cable jointing kit (outdoor) /11 kv 3×50mm2 xlpe cable jointing kit (outdoor) 11 11 kv 3×185mm2 xlpe cable jointing kit (indoor) / 11 kv 3×50mm2 xlpe cable jointing kit (indoor) 12 stone pad (300×300×75mm) 13 number plate with clamp & nuts 14 danger board & clamps with bolts and nuts 15 ms nut & bolts 16 m.s. earthing rod of 20×2500mm and 6 swg wire 17 stay complete (stay rod 16×1800mm, stay wire 5 kg, stay insulators, sty clamps, bolts & nuts with grouting) 18 barbed wire gi 19 11 kv tpmo with fixing clamp (3 phase) 20 11 kv fuse set (drop out) with fixing clamp (3 phase) 21 holding clamp for gi pipe 22 holding clamp for channel and angle 23 g.i. channel 100×50×6mm, 2240mm 24 g.i. channel 100×50×6mm, 2028mm 25 g.i pipe 150 mm dia, 3 mtr long 26 33kv ct junction box 27 safe carriage of following with loading & unloading at both ends respectively. (under jurisdiction of pvvnl)for item no. 2.01 to 2.112.01 11 kv incoming switch gear 600/300/5a 350mva 28 11 kv outgoing switch gear 200/100/5a 350mva 29 33kv mocb/vcb 800a750mva 30 33kv control panel for double t/f without differential relay 31 33kv ct 200/100/1 1a 32 acsr dog conductor 33 11kv 3x300 mm2xlpe cable / 11kv 3x185mm2 xlpe cable / 11kv 3x50mm2 xlpe cable 34 11 mtr. st pole, sp 55 bottom galvanized 35 11 kv disc insulators t&c type 45 kn polymeric 36 11 kv disc fitting 45 kn 37 11 kv polymeric pin insulator 38 renovation/ repairing of old transformer plinth 39 disconnecting ht cable connection from 33kv side &11kv side of 05mva/8mva power transformer for removing power transformer from plinth after proper shutdown. dismantling of 11kv cable support structure, copper bus bar structure, m.s.frame etc. 40 disconnecting copper flexible/earthing strip from power transformer neutral & dismentling neutral earthing systemto facilitate removal of power transformer from plinth. 41 disconnecting earthing strip from body of 05mva/8mva power transformer. 42 draining of transformer oil from conservator, radiators of existing 05 mva/08mva t/f, at respective 33/11 kv s/s into the dry & clean drums and stacking at the safe place in substation outside of switchyard. empty drums shall be provided & arranged by contractor. 43 removal of conservator, radiators and other accessories from existing 05 mva/08mva power transformer. 44 safe shifting of 05 mva/08mva power transformer main body and other accessories from the substation switchyard to outside the switchyard at suitable place assigned by concern j.e/s.d.o 45 safe shifting of 10mva/05mva, 33/11 kv, power transformer from out side of switchyard to near power transformer plinth in switchyard. 46 erection & installation of 10mva/05mva power transformer on power transformer plinth by fixing all accessories like radiators, conservator tank, filling the transformer oil to desired level and ensuring that there is no leakage, complete job in all respect. reconnecting 2 nos. earthing strip to transformer body. 47 earthing of outdoor equipments in switchyard, as per site requirement/as per pvvnl guideline details as given below: for item no. 7.01 to 7.027.01 providing &laying of g.i.strip of size 50x6mm for connecting the earthmat with each equipment (bus isolators, 33kv c.t., 33kv v.c.b., l.as., fuse set, post insulators, t/f body & its neutral and m.s.frame of cabe supporting structure), various steel structures. the work also includes cutting, bending, straightening, over laping and welding the earth strip with earth mat and by using high quality arc welding in already digged trenches, as per pvvnl guidline and as per site requirement. 48 providing m.s round 32mm dia and making delta earthing for power t/f neutral/l.a as per respo norms. 49 making earthing of all 11kv switchgears, p.t. and other outdoor equipments on both earth terminal inside the control room by providing g.i.strip in size 50x6mm. with 32mm. dia m.s.round laid in trench with proper electric welding, as per pvvnl guidline. 50 supply & erection of water level earthing by boring and lowering by providing of g.i.pipe size 40mm dia, into the ground upto water level or minimum 20mtr, which ever is more, with the lower end of solid copper cone approx 224mm long and 750gm in weight shall be provided and screwed in pipe as well as bringing out a continuous copper wire 6 swg, from the cone upto the ground surface where it will be bolted to the g.i. strip for transformer neutral connection, the g.i.strip will be connected to star point through providing copper bond strip of size 35x6mm, as per pvvnl guidline. 51 excavation of earth in size, erection of structure by making plinth c.c ratio 1:3:6, 12mm thick plasting on plinth in ratio 1:4 : 10.01 – 33kv c.t strucure 52 installation & mounting of materials on erected structure (the work also includes safe removal of old items & height incrasing of existing structures by providing m.s channel/angle as per site requirement if applicable) : for item no. 11.01 to 11.0111.01 33kv c.t (200/100/1a, 400/100/1a) 53 mounting of 33kv fuse set 54 mounting of 33kv l.a 55 33kv bus isolator / line isolator 56 hight increasing of old structures by providing required size g.i/m.s channel/angle as per site requirement (mounted item safely remove, after hight increasing item safely mounted on structures) : for item no. 12.01 to 12.0812.01 33kv fuse set structure 57 33kv l.a structure 58 construction of plinth for the structure of 33 kv vcb as per details : for item no. 13.01 to 13.05.13.01 a) excavation of earth of size (2.4×1.5×1.0) m pits for construction of plinth. (3.6 cum) 59 b) brick ballast ratio (1:4:8) (cement, sand & brick ballast ) for foundation work (2.4×1.5×0.15)m plinth. (0.54 cum) 60 c) c.c. work in ratio 1:2:4 (cement, coarse sand &stone grit) of 20mm size for making plinth of size (2.4×1.5×1.00)m and grouting of foundation bolts 04 nos. for 33 kv vcb. (3.6 cum) 61 d) 12 mm thick plaster with cement mortar in ratio 1:4 (cement & fine sand) of plinth of 0.15 m above ground level size (2.4×1.5)m. (4.77 cum) 62 e) assembling and installation of 33 kv vcb on the vcb out door structure on the plinth.adjustment of operating mechanism in proper alignment for smooth operation of the same. the work also includes fabrication of addition arrangement for proper fixing, if required and also safe removal of old 33kv vcb if applicable. 63 laying, stringing & sagging of acsr dog conductor from main bus bar to power t/f, through post insulator, bus isolator, c.ts, vcb and l.as., byproviding & fixing p.g.clamp/connectors, suitable for dog/panther. 64 erection of i/c switchgear, bus coupler, o/g switchgears & double t/f control panel in alignment, in control room, including safe shifting, from dump place. the work also includes safe removal of old switch gears to safe place if applicable. making 4no. pockets for each and providing/fixing of reg bolt by cc in ratio 1:2:4, with tightening also. as per pvvnl guidline. 65 commissioning & fixing of bus bar (copper), between each switchgear, double t/f control panel control cable, by bolt, nut & washers and ht compound and providing & tapping ht tape, empire tape & pvc tape, on each joint & bus coupler connect which existing bus bar. ( if extra fitting/adjustment or suitable copper bus bar for fitment required then provided by the contractor) 66 construction of double pole structure : providing supply of complete materials & erection for double pole structure on stp 11m.long, with fabrication of all accessories, such as channel/angle, 11kv tpmo, fuse set, disc insulator & pin insulators etc & fixing of all accessories on double pole, by providing &fixing m.s.clamp withbolt,nut&washers. earthing to be provided on each supports by providing & driving m.s.earthing rod and connecting between rod &supports, by providing, g.i wire of 6 swg as per respo norms. 67 grouting of stp 11m. long, with cc in ratio 1:4:8, complete in all respect, as per respo norms. 68 providing of stay set 16x1800mm. on double pole, including digging of pits of size 0.75x0.75x1.5m. grouting in cc ratio 1:4:8 cement, sand & stone shingle. binding and nozelling of stay wire, complete in all respect, by providing & fixing of stay clamp, as per respo norms. 69 preparation of 11 kv power cable ends: as per respo specification of the following : for item no.20.01 to 20.0220.01 making ofcable end termination by heat shrinkable out door jointing kits suitable for 11kv, 3x300q.mm xlpe cable. providing, fixing and crimping of proper size good quality lugs complete in all respect. 70 making ofcable end termination by heat shrinkable indoor jointing kits suitable for 11kv, 3x300sq.mm xlpe cable.providing, fixing and crimping of proper size good quality lugs complete in all respect. 71 preparation of 11 kv power cable ends: as per respo specification of the following : for item no.21.01 to 21.0221.01 making ofcable end termination by heat shrinkable out door jointing kits suitable for 11kv, 3x185q.mm xlpe cable. providing, fixing and crimping of proper size good quality lugs complete in all respect. 72 making ofcable end termination by heat shrinkable indoor jointing kits suitable for 11kv, 3x185sq.mm xlpe cable.providing, fixing and crimping of proper size good quality lugs complete in all respect. 73 providing all required materials & fabrication and erection of neutral earthing l type support made of m.s. channel size 100×50mm. structure shall be 4 mtr. long with 1 mtr. arms. structure shall be grouted in ratio 1:3:6 in block size 300×300×700mm and painted with one coat of ready mixed primer and two coat of enamel aluminium paint work includes connecting neutral bushing rod of power transformer and m.s. earthing strip with the help of flexible copper bond size 35x6mm m.s. bolt and washer. 74 cable support : for item no. 23.01 to 23.0223.01 supply & fabrication and erection of cable support made of two pieces of m.s. channel (100x50x6)mm, 2.75 meter long, joined to each other by means of 5 nos. m.s. angle (50x50x6) mm pieces of size 0.75mtr long each by welding at equal intervals and grouting in a block of size (300x1000x1000)mm in c.c. 1:3:6 complete with one coat of ready mixed primer and two coats of al. paint. work includes providing of three nos. m.s. clamps made of (50x6)mm m.s. flat for holding the cable including nuts and bolts with stone pad of size (300x300x75mm). 75 providing & fixing 110mm dia 2mm thick 2m long g.i.pipe over 11kv, 3x300sq.mm xlpe cable before mounting the 2no. cable on cable support structure. work includes fixing of clamp, sealing of top and bottom end of the g.i.pipe. one end of g.i.pipe is to be buried under earth about 500mm. 76 copper bus bar support t type m.s.structure(as per site requirement) : for item no.24.01 to 24.0224.01 supply & fabrication and grouting of m.s. frames 3.60 mt. long for support of copper bus bar. bus bar will be provided in l.v. side of power transformer. the m.s. frame shall be made of m.s. channel (100x50)mm in t shape. providing 2 nos. support of m.s. angle iron (50x50x6)mm, 0.60mt. long below the top channel, drilling of 3 nos. hole on the top channel for fixing of 03no. 33 kv post insulator. the m.s. frame shall be painted with one coat of primer & two coat of aluminium paint and grouting the frame in c.c. ratio 1:3:6 in a block of size (300x300x700) mm with stone pad of size (300x300x75mm). the work also includes the fixing of 33kv post insulator by aluminium binding wire in complete with nut & bolts. 77 supply & fabrication of copper bus bar of size (2400x50x6)mm in l.v. side for 05mva and (3000x65x8)mm for 10mva t/f as per requirementfor power transformer, work includes connection of outside bus bar in l.v. side busing rod of power transformer and other side with outdoor 11 kv cable box as well as providing empire tape and h.t. tape etc. for proper insulation work covering copper bus bar in complete. 78 fixing of cable box on 5mva/10mva t/f, 11kv switchgears, by bolt & nuts and tapping the joints by providing ht/empire/pvc tape. 79 h.t. power cable laying : for item no.26.01 to 26.0226.01 laying and dressing of 11 kv 3×300 mm2/3×185 mm2 power cable in air/trench. 80 laying 11 kv, 3×300mm2/3×185mm2 xlpe, power cable from power t/f to incoming switchgear/outgoing switch gear to 11 kv double poles in the cable trench 0.45m wide, 0.90m depth. providing 150 mm thickness local sand for cushion beneath and 150 mm above the cable (quantity of local sand required 0.375 cubm/m in length). the cable shall be duly protected by brick. on both side of cable by laying bricks vertically and bricks would also be laid horizontally on top of vertically laid bricks along the cable (minimum 18 nos. per mtr. length are to be laid top and outer side along the cable. the work includes digging of trenches, laying of cable in under ground trenches, joining of terminals, back filling of earth and testing and commissioning of power cables etc. spare cable shall be left over and laid in the trenches in shape of 6m rings at both ends. at the end of feeder cables, where the cable is to be laid across pucca/main road,150 mm dia g.i. pipe will be weared over the cable in the cable trench for the protection of cable. g.i pipe 150mm dia will be provided by contractor. 81 laying of control cable in packka trench, from vcb/cts/t/f to 33kv control panel and making connection for operation & protection of equipments, by using ferrules including commissioning battery charger with battery by providing copper lead with lugs etc & dressing of control cable and making arrangement for testing in the equipments. 82 construction of control cable trench in switchyard : for item no. 28.01 to 28.05 (as per respo norms)28.01 – excavation of earth in size 0.80x0.40m., c.c.work in foundation in ratio 1:4:8 (cement, sand & brick ballast) with proper ramming in size 0.80x0.15m., ist class brick work in cement mortar in ratio 1:4. as per site requirement. 83 providing &grouting of m.s.strip of size 25x6mm in cable trench 100mm above floor level and at equal space distance 300mm 84 providing and grouting of m.s.angle iron of size 50x50x6mm in upper edge of trench. 85 c.c.work on the top in the ratio 1:2:4 in the grouting of edge of the trenches. & plastring of trench. 86 providing fabrication and fixing cable trench cover of providing m.s.angle iron size 40x40x6mm of size 0.3m wide 0.5 to 1.0 mtr length. as per site requirement. after construction of cable trench. 87 painting of the following structure with one coat of ready mixed primer and two coats of isi mark alumn. paint after rubbing with sand paper to the surface of the structure includidng labour and t&p complete in all respect.:for item no.29.01 to 29.0529.01 – line isolator structure 88 fuse set structure 89 post insulator, l.a.structure 90 v.c.b.structure, c.t.structure 91 m.s.frame for cable 92 hiring of d/g set, including carriage, loading, unloading & operating charges (with fuel) at 33/11kv substation, :for item no. 30.01 to 30.0230.01 – 20 kva, 3 phase d/g set for testing of power t/f & equipments installed at sub station. 93 5 kva, single phase d/g set for welding/testing of equipments installed at sub station. 94 providing required no. ofskilled technicians for testing & commisning to work on power t/f, ht/lt panels, during testing as assisting technical hands of test team during commissioning & energisation. after installation of new protection equipments (33kv vcb, c.t & double t/f, single t/f control panel) the contractor will ensure its testing on his own expences. 95 carriage of received back material from site to concerned electricity store center : for item no. 32.01 to 32.0432.01 – double transformer control panel (old & damage) 96 33kv vcb (old & damage) 97 33kv ct 200/100/1 1a (old & damage) 98 05/08mva transformer (old & used) ...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39898671 tender for carrying out various electric works on semi turn key basis for system strengthening in municipal area in the area of ee, eudd ii, mathura under the jurisdiction of se, eudc, mathura cartage of following material from store centre, mathura to work site. 2 st pole ( 11 mtr. long ) ( bottom portion galvanized ) 3 pcc pole ( 8.5 mtr. long ) 4 st pole pole ( 13 mtr. long ) ( bottom portion galvanized ) 5 11 / 0.43 kv 400 kva t / f 6 11 / 0.43 kv 250 kva t / f. 7 11 / 0.43 kv 100 kva t / f. 8 11 / 0.43 kv 63 kva t / f. 9 lt aerial bunch conductor. 3x120 sq.mm. 10 lt xlpe cable al 1x400 sq.mm. 11 lt pvc cable 1x630 sq.mm. 12 lt pvc cable 1x400 sq.mm. 13 al xlpe cable 1x630 sq.mm. 14 al. xlpe 1x400 sqmm. cable 15 al. xlpe 1x240 sqmm. cable 16 lt pvc cable 3.5x150sq.mm. 17 lt pvc cable 3.5x240sq.mm. 18 lt pvc cable 3.5x70sq.mm. 19 33 kv xlpe cable 3x300 sq.mm. 20 11 kv xlpe cable 3x185 sq.mm. 21 11 kv xlpe cable 3x70 sq.mm. 22 2cx10 sq.mm. armoured cable 23 4x10 sq.mm. armoured cable with catenary arrangement 24 indoor cable jointing kit i / d 11 kv 3x185 sq.mm. 25 outdoor cable jointing kit o / d 11 kv 3x185 sq.mm. 26 straight through for 11 kv 3x185 sq.mm. 27 outdoor cable jointing kit o / d 11 kv 3x70 sq.mm. 28 outdoor cable jointing kit o / d 33 kv 3x300 sq.mm. 29 acsr ins. weasel conductor 30 acsr weasel conductor 31 acsr dog conductor 32 d.o. fuse set for 11 kv 33 cartage of above material like various size 33 kv, 11 kv cable, dog / weasel conductor, jointing kit, vaccume interrupter, distribution transformers, st / pcc pole, vcb, insulator, disc. fitting, control panel, pin insulator, bus isolator, line isolator, bus coupler, brass glands, channel, clamps etc. from store center, mathura to work site and dismentled material from site to dvvnl store. 34 digging of pit & erection of new single support st pole ( 13 / 11 mtr. long ) including grouting of pole and fixing of all clamps, cross arm, pin / disc insulator & other accessories with providing stone pad as per relevant drawings. any fabrication if required for above support. 35 digging of pit & erection of new double pole structure st pole ( 13 / 11 mtr. long ) including grouting of pole and fixing of all sturucture accessories, clamps, cross arm, pin / disc insulator & other accessories with providing stone pad as per relevant drawings. any fabrication if required for above support. 36 earthing of st / pcc pole / body earthing of t / f. by m.s earth rod. 37 providing & fixing of ms nut, bolt and washers 38 providing & painting of st pole with aluminum paint and red oxide. 39 digging of pit & erection of stay rod with grouting cement sand and brick ballast including nuzzling, binding complete. ( stay insulator providing by contractor ) 40 filling & fixing of 11 kv indoor type cable jointing kit for 11 kv 3x185 sqmm.xlpe cable 41 filling & fixing of 11 kv outdoor type cable jointing kit for 11 kv 3x185 sqmm.xlpe cable 42 filling & fixing of 11 kv cable jointing kit ( straoght through ) for 11 kv 3x185 sqmm.xlpe cable 43 filling & fixing of 11 kv outdoor type cable jointing kit for 11 kv 3x70 sqmm.xlpe cable 44 filling & fixing of 33 kv indoor type cable jointing kit for 33 kv 3x300 sqmm.xlpe cable 45 sagging of weasel / dog conductor on erected poles. 46 sagging / jumpering of ins. weasel / dog conductor 47 digging of trenchby making pits / open trench method / hdd method after due survey with the help of utility detector of existing electrical / telephonic cable / and other utilites of public utilites departmentand laying , testing, commisiong & energization of cables of 33 kv / 11 kv xlpe double ckt. cable by manual drill ( by making moles ) / hdd method / open trench including all material like brick & sand and back filling and restoring the road to make as original. 48 sagging & laying of 33 / 11 kv xlpe cable in double pole structure / loop etc. 49 laying of laying of2c / 10 sq.mm. armoured cable 50 laying of 4x10 xlpe armoured cable with catenary arrange ment 51 digging of trenchby making pits / open trench method / hdd method after due survey with the help of utility detector of existing electrical / telephonic cable / and other utilites of public utilites departmentand laying , testing, commisiong & energization of cables of lt xlpe / pvc / al. double ckt. cable by manual drill ( by making moles ) / hdd method / open trench including all material like brick & sand and back filling and restoring the road to make as original. 52 sagging & laying of lt cable 3.5x150 / 240sq.mm. 53 laying of lt abc 3x120 sq.mm. cable 54 laying lt xlpe cable al 1x400 sq.mm. 55 laying lt pvc cable 1x630 sq.mm. 56 laying lt pvc cable 1x400 sq.mm. 57 laying al xlpe cable 1x630 sq.mm. 58 laying al. xlpe 1x400 sqmm. cable 59 laying al. xlpe 1x240 sqmm. cable 60 guarding of 33kv / 11 kv line. ( including g.i. wire and other related items ) 61 providing and fixing of 11 kv holding clamp for st pole 62 providing & fixing of g.i. pipe 4 / 6 dia 63 providing & fixing of clamp for g.i. pipe 64 providing & fixing of guarding angle for 33 / 11 kv 65 providing & fixing of i bolt for guarding 66 providing & fixing of aluminium biding wire for guarding 67 providing & fixing of clamp for guarding angle for 11 kv line 68 providing & fixing of cable end termination using total double compression brass glands for 3.5x70 sq.mm. xlpe cable 69 providing & fixing of cable end termination using total double compression brass glands for 3.5x150 sq.mm. xlpe cable 70 providing & fixing ofcable end termination using total double compression brass glands for 3.5x240 sq.mm. xlpe cable 71 a 1 type distribution panel with ats switch & controller 800 amp.supply &erectionoffactory fabricated&wired metalcladdustandverminprooffloormounting double door type outdoor application, with m.s.channel base with bottom and top cable entries shall be detachable type gland plateelectricalcontrolpanelwithtpnacb ( 65 ka, 4pole elect draw out , micro processer release icu=icw=ics 1sec ) with short circuit protectionand tpnmccbs ( fourpole50kawith thermalmagneticrelease with adjustable over current and short circuit protection, ics=100% icu, suitable for 415 v ac ) switchesandinstrument chamber etc. complete in all respects. the instrument chamber shallbeseparate and incoming section connecting with proper horizontal / vertical busbar and outgoing section with cable alley sectionandshall metering with digital multifunction meter with inbuilt selector switches, instrument fuses, red yellow and blue phase indicators in incoming section, currenttransformeretc.the boardshallhave suitablecapacity electrolyticaluminumbusbarsas peris8623insulatedwithheatshrink color codesleeveand mounted on non hygroscopic supports such as cmc / dmc support with detachable side covers and shall be suitable for extension on the sides. the switches entryboxesshallbecompletewithsuitablecable end boxes. ( incoming : 1250ampacb1 noand outgoing 400 amp mccb 6 nos and 250 amp mccb 2 nos with extended rotary handel, spreder set , phase barrier etc ) theswitchboardshallbe fabricated with galvanized primesheet with a minimum thickness of 1.6 mm / 2mm. with seven tank process powder coated switchgear.the jobincludesthe disconnecting anddismantling of existing a 1 type distribution panel including of complete replace old burn cables ends and joint new cable with cable jointers, luges, double compression glands, etc new cables will joint as per connected sizes in incoming and outgoing sections, the grounding ofthe panel boardas per directionsofengineer incharge. 72 a 2 type distribution panel with ats switch & controller 630 amp.supply &erracetionoffactory fabricated&wired metalcladdustandverminprooffloormounting double door type outdoor application, with m.s. channel base with bottom and top cable entreis shall be detachable type gland plateelectricalcontrolpanelwith tpnmccbs ( fourpole50kawith thermalmagnaticrelease with adjustable over current and short circuit protection, ics=100% icu, suitable for 415 v ac ) switchesandinstrument chamber etc.complete in all respects. the instrument chamber shallbeseparate and incomming section connecting with proper horizental / vertical busbar and outgoing section cable alley sectionandshall metering with digital multifuncation meter, with inbuilt selector switches, istrument fuses, red yellow band blue phase indicators in in comming section, currenttransormeretc.the boardshallhave suitablecapacity electrolyticaluminiumbusbarsas peris8623insulatedwithheatshrink color codesleevand mounted on non hygroscopic supports such as cmc / dmc support with deteachable side covers and shall be suitable for extension on the sides. the switches entryboxesshallbecompletewithsuitablecable end boxes. incoming : 800ampacb 1 noand outgoing 400 amp mccb 02 nos., 250 amp mccb 05 nos., 100 amp mccb 2 nos. with extended rotary handel, spreder set , phase barrier etctheswitchboardshallbe fabicated with gelvnized primesheet with a minimum thickness of 1.6 mm / 2mm. with seven tank process powder coated switchgear make : scheinder / abb / siemens / c&sthe jobincludesthe disconnecting anddismentling of existing a 2 type distribution panel including of complete replace old burn cables ends and joint new cable with cable jointers, luges, double compression glands, etc new cables will joint as per connected sizes in incoming and outgoing sectionsgrounting ofthe panel boardas per directionsofengineer incharge. 73 a 3 type distribution panel with ats switch & controller 400 amp.supply &erracetionoffactory fabricated&wired metalcladdustandverminprooffloormounting double door type outdoor application, with m.s. channel base with bottom and top cable entreis shall be detachable type gland plateelectricalcontrolpanelwith tpnmccbs ( fourpole50kawith thermalmagnaticrelease with adjustable over current and short circuit protection, ics=100% icu, suitable for 415 v ac ) switchesandinstrument chamber etc.complete in all respects. the instrument chamber shallbeseparate and incomming section connecting with proper horizental / vertical busbar and outgoing section cable alley sectionandshall metering with digital multifuncation meter, with inbuilt selector switches, istrument fuses, red yellow band blue phase indicators in in comming section, currenttransormeretc.the boardshallhave suitablecapacity electrolyticaluminiumbusbarsas peris8623insulatedwithheatshrink color codesleevand mounted on non hygroscopic supports such as cmc / dmc support with deteachable side covers and shall be suitable for extension on the sides. the switches entryboxesshallbecompletewithsuitablecable end boxes. incoming : 630ampacb 1 noand outgoing 250 amp mccb 5 nos and 100 amp mccb 2 nos with extended rotary handel, spreder set , phase barrier etctheswitchboardshallbe fabicated with gelvnized primesheet with a minimum thickness of 1.6 mm / 2mm. with seven tank process powder coated switchgear make : scheinder / abb / siemens / c&sthe jobincludesthe disconnecting anddismentling of existing a 3 type distribution panel including of complete replace old burn cables ends and joint new cable with cable jointers, luges, double compression glands, etc new cables will joint as per connected sizes in incoming and outgoing sectionsgrounting ofthe panel boardas per directionsofengineer incharge. 74 b 3 type distribution panel with ats switch & controller 250 amp.supply &erracetionoffactory fabricated&wired metalcladdustandverminprooffloormounting double door type outdoor application, with m.s. channel base with bottom and top cable entreis shall be detachable type gland plateelectricalcontrolpanelwith tpnmccbs ( fourpole50kawith thermalmagnaticrelease with adjustable over current and short circuit protection, ics=100% icu, suitable for 415 v ac ) switchesandinstrument chamber etc.complete in all respects. the instrument chamber shallbeseparate and incomming section connecting with proper horizental / vertical busbar and outgoing section cable alley sectionandshall metering with digital multifuncation meter, with inbuilt selector switches, istrument fuses, red yellow band blue phase indicators in in comming section, currenttransormeretc.the boardshallhave suitablecapacity electrolyticaluminiumbusbarsas peris8623insulatedwithheatshrink color codesleevand mounted on non hygroscopic supports such as cmc / dmc support with deteachable side covers and shall be suitable for extension on the sides. the switches entryboxesshallbecompletewithsuitablecable end boxes.incoming : 250 ampmccb1 noand outgoing 100 amp mccb 04 nos with extended rotary handel, spreder set , phase barrier etctheswitchboardshallbe fabicated with gelvnized primesheet with a minimum thickness of 1.6 mm / 2mm. with seven tank process powder coated switchgear switchgear make : scheinder / abb / siemens / c&sthe jobincludesthe disconnecting anddismentling of existing b 3 type distribution panel including of complete replace old burn cables ends and joint new cable with cable jointers, luges, double compression glands, etc new cables will joint as per connected sizes in incoming and outgoing sectionsgrounting ofthe panel boardas per directionsofengineer incharge. 75 c paneldisconeccting and dismentlingof existing c panel and supply, installation testing commisioning offactory fabricated&wired metalcladdustandverminproof double door typeoutdoor application stand mounting, m.s. channel base incliding channel stand with bottom cable entreis the panel boardshall havesuitablecapacity electrolytic alumininum busbars asper is8623 or above istulated with heat shrink sleeving and mounted on nonhygroscopic supports such as cmc / bmc support. panel shall be completewithsuitablecableendboxes, double compression glands. panel comparment having special provision for internal locking system for stop the electricity theft the panelboard shall be fabricated with gelvnized prime sheet with a minimum thickness of 1.6mm / 2mm. with seven tank process powder coated. panel haveing proper space for connectingincomming and outgoing cable terminations make: apc / scheinder / abb / siemens / c&s & complete with insulation of bakelite strip ( 08 mm / 10 mm ) thickness. 76 earthing complete for c type panels by earth rod 77 providing & fixing of lt acb 800 amp nos. 250 amp. output mccb and suitable covering & mounting strucuture 78 providing & fixing of lt acb 630 amp nos. 250 amp. output mccb and suitable covering & mounting strucuture 79 providing & fixing of foundation of rmu 3 cubic meter 80 pipe and pipe gel earthing for r.m.u 81 providing & fixing of danger board 82 providing & fixing of barbed wire 83 sagging of guarding g.i. wire 84 providing & fixing of stone pad 85 providing & fixing of boot protection for t / f monkey fault 86 providing & fixing 16 sqmm. alumimum thimble 87 providing & fixing of pvc pipe 3 of diameter 88 providing and instllation of 24 volt battery with charger. 89 providing & fixing of 33 kv v type steel cross arm 90 provoding & fixing of 11 kv v type steel cross arm 91 providing & fixing of 11 kv pin insulator with pin 92 providing & fixing of 33 kv v type steel cross arm holding clamp 93 providing & fixing of 11 kv v type steel cross arm holding clamp 94 providing & fixing of 33 kv pin insulator with pin 95 providing & fixing of disc insulator 45 kn & 70 kn ( t&c / b&s ) with fitting 96 providing & fixing of 33 kv f bracket 97 providing & fixing of 11 kv f bracket 98 providing & fixing of packing piece clamp for 33 kv / 11 kv with nut & bolts 99 providing & fixing of aluminium lug 25 sqmm. 100 providing & fixing of aluminium lug 70 sqmm. 101 providing & fixing of aluminium lug 150 sqmm. 102 providing & fixing of aluminium lug 240 sqmm. 103 providing & fixing of aluminium lug 400 sqmm. 104 providing & fixing of aluminium lug 630 sqmm. 105 providing & fixing of aluminium lug 1000 sqmm. 106 providing & sagging / fixing of al. xlpe 1x1000 sq.mm. cable 107 installation of 11 / 0.4 kv, 400 kva t / f mobile trolley 108 providng trolley structure for 400 kva t / f with vehicle tyre, rim, coupling, trolly hook, earthing, painting and related accessories with complete job 109 supply of g.i. pipe chemicalearthing electrode 3 mtr. long 80 mm inner dia along with chemical powder and 50x6 mm g.i. strip with nut, bolt and washer. 110 earthing of power transformer ( urban ) by digging of pit up to water level depth approx. 90 feet. into the boring 1 1 / 4 dia gi pipe of b grade, conforming to the requirement of is specification and then connecting the top of the inserted pipe and power transformer body earthing through m.s. strip of size 50x6mm with the help of electric welding lum sum rate. it includes the cost of all material, labour, carrier etc. required for proper completion of work. 111 installation of d.o. fuse set of 11 kv 112 supply, install, testing and commisioning of 11 kv 630 amps 21 ka for 3 sec. sf6 insulated, one side extesible, outdoor duty 3 way r.m.u. manual operate, in combination of 01 nos. vcb modules ( o / g ) & 2 nos. load breakerswitch modules ( i / c ) , consitiing of copper busbar in sf6 insulated 304 ( non ferrite non magnetic grade ) stainless steel enclosure of thickness 2.5 mm with manometer fixed on the tank. the breaker shall have mechanical on / off indicator with hand trip device and spring charging, spring relase coil, auxiliary switch of 02 no +2nc. the hv switchgerar and control gear should be confirming to iec 62271 100, iec 62271 200 2003 & iec 60694 1996. the rmu gas tank should be internal arc tested for 21 ka for 1second with iac afl classification for gas tank. the complete rmu should have ingress protection of minimum ip54. the rmu design should support site replaceable ht cable bushing. all the type test certified as per iec from third party lab to be submitted. rmu should have : 01 nos. micorprocessor based self powered numerical relay with over current / earth fault & short circuit protection wiht each vcb feeder. 3nos. protection ct shall be of burden 2.5 va, ratio 200 / 1a, class of accuracy class 5p10 for o / c and e / f protection for each vcb. ( ct ration is indicative and may vary during detailed engineering ) 1 no. manometer for each tank 1 nos. voltage passage indicator for each feeder. 1 nos. fault passage indicator for each lbs module. right angle boots for all the feeder modules basic insulation level of complete system shall be 28kv ( rms ) / 75kv ( peak ) vacuum interrupter & rmu should be of same make for better life cycle optimization. 113 supply, install, testing and commisioning of 11 kv 630 amps 21 ka for 3 sec. sf6 insulated, one side extesible, outdoor duty 4 way r.m.u. manual operate, in combination of 02 nos. vcb modules ( o / g ) & 2 nos. load breakerswitch modules ( i / c ) , consitiing of copper busbar in sf6 insulated 304 ( non ferrite non magnetic grade ) stainless steel enclosure of thickness 2.5 mm with manometer fixed on the tank. the breaker shall have mechanical on / off indicator with hand trip device and spring charging, spring relase coil, auxiliary switch of 02 no +2nc. the hv switchgerar and control gear should be confirming to iec 62271 100, iec 62271 200 2003 & iec 60694 1996. the rmu gas tank should be internal arc tested for 21 ka for 1second with iac afl classification for gas tank. the complete rmu should have ingress protection of minimum ip54. the rmu design should support site replaceable ht cable bushing. all the type test certified as per iec from third party lab to be submitted. rmu should have : 01 nos. micorprocessor based self powered numerical relay with over current / earth fault & short circuit protection wiht each vcb feeder. 3nos. protection ct shall be of burden 2.5 va, ratio 500 / 1a, class of accuracy class 5p10 for o / c and e / f protection for each vcb. ( ct ration is indicative and may vary during detailed engineering ) 1 no. manometer for each tank 1 nos. voltage passage indicator for each feeder. 1 nos. fault passage indicator for each lbs module. right angle boots for all the feeder modules basic insulation level of complete system shall be 28kv ( rms ) / 75kv ( peak ) vacuum interrupter & rmu should be of same make for better life cycle optimization. 114 supply, install, testing and commisioning of 11 kv 630 amps 21 ka for 3 sec. sf6 insulated, one side extesible, outdoor duty 5 way r.m.u. manual operate, in combination of 03 nos. vcb modules ( o / g ) & 2 nos. load breakerswitch modules ( i / c ) , consitiing of copper busbar in sf6 insulated 304 ( non ferrite non magnetic grade ) stainless steel enclosure of thickness 2.5 mm with manometer fixed on the tank. the breaker shall have mechanical on / off indicator with hand trip device and spring charging, spring relase coil, auxiliary switch of 02 no +2nc. the hv switchgerar and control gear should be confirming to iec 62271 100, iec 62271 200 2003 & iec 60694 1996. the rmu gas tank should be internal arc tested for 21 ka for 1second with iac afl classification for gas tank. the complete rmu should have ingress protection of minimum ip54. the rmu design should support site replaceable ht cable bushing. all the type test certified as per iec from third party lab to be submitted. rmu should have : 01 nos. micorprocessor based self powered numerical relay with over current / earth fault & short circuit protection wiht each vcb feeder. 3nos. protection ct shall be of burden 2.5 va, ratio 500 / 1a, class of accuracy class 5p10 for o / c and e / f protection for each vcb. ( ct ration is indicative and may vary during detailed engineering ) 1 no. manometer for each tank 1 nos. voltage passage indicator for each feeder. 1 nos. fault passage indicator for each lbs module. right angle boots for all the feeder modules basic insulation level of complete system shall be 28kv ( rms ) / 75kv ( peak ) vacuum interrupter & rmu should be of same make for better life cycle optimization. 115 supply &erection offactory fabricated&wired metalcladdustandverminprooffloormounting double door type outdoor application, with m.s. channel base with bottom and top cable entreis shall be detachable type gland plateelectricalcontrolpanelwith 01 no. 630 amp. acb& 03 no. 250 amp. mccb the instrument chambershallbeseparate and incomming section connecting with proper horizental / vertical busbar and outgoing section with cable alley sectionandshall metering with digital multifuncation meter with inbuilt selector switches, istrument fuses, red yellow and blue phase indicators in incomming section, currenttransormeretc.the boardshallhave suitablecapacity electrolyticaluminiumbusbarsinsulatedwithheatshrink color codesleevand mounted on non hygroscopic supports such as cmc / dmc support with deteachable side covers and shall be suitable for extension on the sides. the switches entryboxesshallbecompletewithsuitablecable end boxestheswitchboardshallbe fabicated with gelvnized primesheet with a minimum thickness of 1.6 mm / 2mm. with seven tank process powder coated 116 supply &erection offactory fabricated&wired metalcladdustandverminprooffloormounting double door type outdoor application, with m.s. channel base with bottom and top cable entreis shall be detachable type gland plateelectricalcontrolpanelwith 01 no. 800 amp. acb& 01 no. 400 amp. mccb & 02 no. 250 amp. mccbthe instrument chambershallbeseparate and incomming section connecting with proper horizental / vertical busbar and outgoing section with cable alley sectionandshall metering with digital multifuncation meter with inbuilt selector switches, istrument fuses, red yellow and blue phase indicators in incomming section, currenttransormeretc.the boardshallhave suitablecapacity electrolyticaluminiumbusbarsinsulatedwithheatshrink color codesleevand mounted on non hygroscopic supports such as cmc / dmc support with deteachable side covers and shall be suitable for extension on the sides. the switches entryboxesshallbecompletewithsuitablecable end boxestheswitchboardshallbe fabicated with gelvnized primesheet with a minimum thickness of 1.6 mm / 2mm. with seven tank process powder coated 117 supply &erection offactory fabricated&wired metalcladdustandverminprooffloormounting double door type outdoor application, with m.s. channel base with bottom and top cable entreis shall be detachable type gland plateelectricalcontrolpanelwith 01 no. 1250 amp. acb, 02 no. 400 amp. mccb & 02 no. 250 amp. mccbthe instrument chambershallbeseparate and incomming section connecting with proper horizental / vertical busbar and outgoing section with cable alley sectionandshall metering with digital multifuncation meter with inbuilt selector switches, istrument fuses, red yellow and blue phase indicators in incomming section, currenttransormeretc.the boardshallhave suitablecapacity electrolyticaluminiumbusbarsinsulatedwithheatshrink color codesleevand mounted on non hygroscopic supports such as cmc / dmc support with deteachable side covers and shall be suitable for extension on the sides. the switches entryboxesshallbecompletewithsuitablecable end boxestheswitchboardshallbe fabicated with gelvnized primesheet with a minimum thickness of 1.6 mm / 2mm. with seven tank process powder coated 118 providing & fixing of dead end clamp with i hook 119 providing & fixing of suspension clamp with i hook 120 providing & fixing of piercing clamp 121 installation of lt distribution box 122 providing & fixing of pvc pipe 2 of diameter 123 providing & fixing of clamp for distribution box 124 concreting of pole ( st 13 mtr. / 11 mtr. ) pcc pole 125 providing and fixing / installation of compact substation t / f of 400 kva including all relevant and required accessories. 126 removal of old transformer ( 250 kva ) with all connected accessories from existing double pole. 127 removal of old transformer ( 100 kva ) with all connected accessories from existing double pole. 128 removal of old transformer ( 63kva ) with all connected accessories from existing double pole. 129 removal of old transformer ( 25kva ) with all connected accessories from existing double pole. 130 construction of plinth 6x6x4 height from ground as per sc ( as per approved gtp ) 131 installation of following transformer on plinth / double pole with all connecting accessories jumering etc. including carriage of transformers from store centre, mathura to work site. 132 400 kva transformer on plinth 133 250 kva transformer on plinth 134 100 kva transformer on double pole 135 63 kva transformer on double pole 136 providing and installation of tail less unit complete 137 mash / frp fencing of sub station with civil works ( as per approved gtp ) 138 complete pipe in pipe gel earthing of 11 / 0.4 kv 250 / 400 distribution transformer by digging pits 6” dia upto 3 mtr. deep including chemical filled pipe in between ( pipe in pipe ) isi mark b grade & connecting with g.i strip of size 50mm x 6mm with neutral / body of 11 / 0.4 kv distribution transformer to above pipe in pipe ( pip ) and filling of chemical crystalline conductive mixture containing highly conductive material around the ( pipe in pipe ) up to 3 mtr. including making of chamber at the top of the earthing. other details are as below: 1.earth pipe material – mild steel, galvanised.2 main electrode diameter – 42.4mm.3 auxiliary electrode pipe, diameter – 76mm.4 wall thickness of main electrode : 2.6mm.5 wall thickness of auxiliary ist whole: 3.2mm.6 length of earthing electrode ( pip ) : 3 meter. 139 dismantling of damaged & used items i.e. distribution transformer, st / pcc pole, ht / lt cable, conductor ( scrap ) & other accessories at work site and carriage dismantled material from site to store center, mathura. 140 proper road restoration kaccha / pakka ( if required ) rates shall be acceptable, if not given above for the same work....

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39898660 tender for execution of various work for shifting of line under the head full deposit under pmgsy ( work t 01, work t 05, work t 09, work t 10, work mrl 14 ) ( sh 43 to dhaka gaon, mf road to budhayun gaon, hardoi to ashrafpur, budhwana road to nanhora gaon, spn road to guladiyag ) in edd jalalabad under edc shahjahanpur 1 safe carriage including loading / unloading & proper stacking of following store materials from store centre to site of work ( approx. distance 0 50 km. ) 2 s.t pole 13 mtr long 3 s.t pole 11 mtr long 4 pcc pole 9 mtr long 5 pcc pole 8.5 mtr long 6 stone pad 7 top channel 33 kv 8 top channel 11 kv 9 33 kv pin insulator 10 33 kv pin with nut 11 stay complete 12 earthing complete 13 top & dropper chanel clamp for stp ( provided by contractor ) 14 m.s. nut & bolt ( provided by contractor ) 15 m.s. angle bracing with nut & bolts ( 65x65x6 ) 16 bracing clamps 6.5 inch dia ( provided by contractor ) 17 earth wire complete with nut bolt 18 top channel 11 kv 19 11 kv disc insulator 20 11 kv disc fitting 21 11 kv pin insulator 22 11 kv pin with nut 23 f clamp 24 11 kv x armholding clamp 25 11 kvv type x arm 26 m.s. t off channel 27 cable lt abc ( 3*50+1*35+1*16 ) sq. mm 28 acsr weasel conductor 29 guarding angle 30 guarding angle clamp with nuts and bolts 31 g.i wire 10 swg 32 barbed wire gi 33 dog conductor 34 errection work 35 fabrication, erection of single pole for 11 kv line on stp 11 mtr long pole with fixing of necessary clamps & other accessories like 1 no. 11kv v type cross arm, 1 no. f clamp. itsgroutinginratio1:4:8, plinthing300mmaboveground level, painting of pole with one coat of red oxide & two coats ofenamelpaint ( isimark ) &earthingofsupportasper ressponorms ( allgrouting&paintingmaterialshallbeprovided by the contractor. ) . 36 fabrication, erection of single pole for 11 kv line on pcc pole 8.50 mtr long pole with fixing of necessary clamps & other accessories like 1 no. 11kv v type cross arm, 1 no. f clamp. itsgroutinginratio1:4:8, asper ressponorms ( allgroutingmaterialshallbe provided by the contractor. ) . 37 fabrication, erection of single pole for lt line on stp 11 mtr long pole with fixing of necessary clamps & other accessories like l.t. clamp, earth wire clamp etc. grouting in ratio 1:4:8, plinthing300mmabovegroundlevel, paintingofpolewith one coat of red oxide & two coats of enamel paint ( isi mark ) & earthing of support as per resspo norms ( all grouting & painting material shall be provided by the contractor. ) . 38 fabrication, erection of single pole for lt line on pcc 8.5mtr long pole with fixing of necessary clamps & other accessories like l.t. clamp, earth wire clamp etc. grouting in ratio 1:4:8, as per resspo norms ( all grouting material shall be provided by the contractor. ) . 39 fabrication, erection ofdouble pole for 11 kv line on pcc pole 9.00 mtr long pole with fixing of necessary clamps & other accessories like 1 no. 1no.topchannel 2240x100x50mm etc. itsgroutinginratio1:4:8, asper ressponorms ( allgrouting materialshallbeprovided by the contractor. ) . 40 fabrication, erection ofdouble pole for 11 kv line on pcc pole 8.5 mtr long pole with fixing of necessary clamps & other accessories like 1no.topchannel 2240x100x50mm etc. itsgroutinginratio1:4:8, asper ressponorms ( allgrouting materialshallbeprovided by the contractor. ) . 41 fabrication, erectionof33kvdoublepolestructureforend terminationson13mlongstpolewithfixingofnecessary clamps&otheraccessorieslike1no.topchannel 3200x125x65mm, msanglecrossbracing.itsgroutingin ratio 1:4:8, plinthing 300 mm above ground level, painting of pole with one coat of redoxide & twocoats of enamel paint ( isi mark ) , earthing of support as per resspo norms & one side cable expose for road crossing ( all grouting material shallbe provided by the contractor. ) . 42 fabrication, erectionof11kvdoublepolestructureforend terminationson11mlongstpolewithfixingofnecessary clamps&otheraccessorieslike1no.topchannel 3200x125x65mm, msanglecrossbracing.itsgroutingin ratio 1:4:8, plinthing 300 mm above ground level, painting of pole with one coat of redoxide & twocoats of enamel paint ( isi mark ) , earthing of support as per resspo norms & one side cable expose for road crossing ( all grouting material shallbe provided by the contractor. ) . 43 erection / fixingforstaysetwithstaywireandclampasper resspo drawing including binding. climbing, clamping, tightening and nozzeling etc. complete in all respect including its grouting in ratio 1:4:8 before back filling of the pits as per resspo, cement, brick, concrete ballast, sand and etc would beprovidedbythecontractorfor33 / 11kvsinglesupport, double pole and four pole structure. 44 stringingandsaggingof11kvoverheadlineonacsr weasel conductor as per resspo norms. 45 stringingandsaggingof33kvoverheadlineonacsr dog conductor as per resspo norms. 46 febrication work of x arm clamps vareios channel etc as per require ment for works completion ( nos ) 47 installation of v type cross arm , guardingangle & clamps etc. 48 stringing and sagging of l.t. line on cable lt abc ( 3*50+1*35+1*16 ) sq. mm as per resspo norms. 49 dismantlingandremovingoffollowinglinesaspernorms complete in all respect 50 dismentlingof11 kvlinecorrsinglenthappox. 950 ckt. mtr. along with accessories 51 dismentling of 33 kv line corrsing lenth appox.200 ckt. mtr. along with accessories 52 dismentling of lt line corrsing lenth appox. 200 ckt. mtr. along with accessories 53 guarding of 11 kv line 54 backcartageoffollowingused / scrap ( receivedby dismantling ) from site to store centre, including / unloading etc. 55 recd. back of 4 no 33 kv line lenth appox. 200 ckt. mtr. 56 recd. back of11kv line lenth appox. 950 ckt mtr. 57 recd. back of 01 no lt line lenth appox. 300 ckt. mtr. 58 fixing of danger board and g.i barbed wire on each pole including proper clamping. ( all material would be provided by contractor ) ....

Uttar Pradesh State Agro Industrial Corporation Limited - Uttar Pradesh

39879710 miscellaneous items , a. supply of , m.s. circular tree guard in one pc. 2100 mm height, 450 mm dia, angle 25x25x3mm, flat 25x3mm, wriemesh 75x75x2.5mm, logo plate 200x100mm, 16g with painting , m.s. cricular tree guard in two pc. 2100 mm height, 450 mm dia, angle 25x25x3mm, flat 25x3mm, wriemesh 75x37.5x2.5mm, logo plate 100x75mm, 22g logo with painting and nut bolts , m.s. square tree guard 500 x500mm, height 1950mm, angle 25x25x3mm, flat 25x3mm, wriemesh 30x30x2.5mm, logo plate 150x100mm, 20g logo with painting , m.s. square tree guard with four crowns 600x600mm, height 1950mm, wt 54.00 kg, made of m.s. pipe 25x25mm, m.s. sqaure bar 8.0mm logo plat 600x300mm, 16g, logo with painting , m.s. square tree guard with four crowns 600x600mm, height 2850mm, wt 54.00 kg made of m.s. pipe 30x30mm, m.s. wiremsh 30x30x12mm, logo plat 600x300mm, 20g, logo with painting , a. r.c.c. fencing pole height 1800mm top 100x100mm, bottom 150x100mm, made of m.s. bar 4.0mm 6 ring, c.c. mix 1:2:4 with painting , b. r.c.c. fencing pole height 1800mm top 100x100mm, bottom 150x100mm, made of m.s. bar 5.0mm, 6 ring, c.c. mix 1:2:4 with painting , c. r.c.c. fencing pole height 1800mm top 100x100mm, bottom 150x100mm, made of m.s. bar 6.0mm, 6 ring, c.c. mix 1:2:4 with painting , a. r.c.c. jali : panel made of 5.0mm, bar size 1800x500x42mm, c.c. mix 1:2:4 with painting and logo writing , b. r.c.c. jali : panel made of 6.0mm, bar size 1800x500x42mm, c.c. mix 1:2:4 with painting and logo writing , hdpe mesh support iront.g. 1800mm (h) 450mm (d) 3ring made of plate (half circle) 25x3mm leg x (25x3mm) , wormi compost in 40.0 kg packed in h.d.p.e. bag , wormi wash in 5 ltr packing , neem ki khali , agriculture grade gypsum powder in 50.0 kg packed in h.d.p.e. bag (inclusive insurance, testing and transportation charges) , barbed wire galvanised hot dip size 12x12g/14x14g , g.i. chain link jali , a. wire size 10g, size 50x50mm, 65x65mm, 75x75mm, 100x100mm , b. wire size 12g, size 50x50mm, 65x65mm, 75x75mm, 100x100mm , iron ghuriya – chhalana , size 7x 3 , size 5x 3 , fencing angle iron with hole & paint size 50x50x5mm height 1800/2100/2400mm...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39845156 various electrical work of electric supply in the area of eudsd iind, etah ( eudd, etah ) under additional business plan ( 339 cr. ) on semi turnkey basis. 2 danger board with barbed wire including jumpering 3 dead end clamp 4 holding clamp for top chanel 5 i hook 6 lt pin clamp for pcc 7 ms droper chanel 8 ms top chanel with clamp 9 nut and bolt with washer 10 stone pad 11 suspension clamp 12 lt incoming panel with metering equipment 13 copper l piece 14 alluminium lug 15 alluminium paint 16 red oxide paint 17 tf base angle 18 prc connector 19 t chanel clamp 20 t chanel 21 lt protection for dt ( mccb ) 22 lt protection of dt 23 dc converter with battery 24 tripping coil for vcb 25 erection work : 26 safe carriage of line material from store center etah to pit site in distance range 0 to 10 km including loading & unloading at both ends. 27 safe carriage of vcb from store center etah to pit site in distance range 0 to 10 km including loading & unloading at both ends. 28 ( a ) 11 kv vcb outgoing / incoming 29 ( b ) 33 kv vcb outgoing 30 safe carriage of33 kv / 11 kv ct from store center etah to pit site in distance range 0 to 10 km including loading & unloading at both ends. 31 safe carriage of 8.5 mtr long pcc pole from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 10 kms.including loading and unloading at both side 32 safe carriage of 11 mtr long st pole from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 10 kms.including loading and unloading at both side 33 safe carriage of following tf from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side. 34 ( a ) 63 / 100 kva tf 35 ( b ) 250 / 400 kva tf 36 erection of 8.5 mtr long pcc pole as single support including fixing of ht / lt accessories etc and other work complete as per respo norms. 37 erection of 11 mtr long st pole as single support including fixing of ht / lt accessories etc and other work complete as per respo norms. 38 erection of 8.5 mtr long pcc pole as double pole / section pole including fixing of ht / lt accessories etc and other work complete as per respo norms. 39 erection of 11 mtr long st pole as double pole including fixing of ht / lt accessories with tpmo etc and other work complete as per respo norms. 40 mounting of following tf on double pole / single pole including making of the connection etc. complete. 41 ( a ) 63 / 100 kva tf 42 ( b ) 250 / 400 kva tf 43 laying, sagging stringing, binding, jumpering & fixing of all accessories etc of following conductor on the newly / old erected pole as per respo manual and as per direction of supervising engineer. it includes the cost of labour, t & p, carrier etc required for proper completion of work. 44 ( a ) acsr weseal conductor 45 ( b ) acsr dog conductor 46 ( c ) lt abc cable 3x120 sqmm 47 ( d ) lt abc cable 3x95 sqmm 48 ( e ) lt pvc cable 1x400 sqmm 49 ( f ) lt pvc cable 1x240 sqmm 50 ( g ) lt pvccable 1x630 sqmm 51 ( h ) lt pvccable al 3.5x150 sqmm 52 earthing complete 53 11 kv vcb o / g ctr 200 / 100 / 5amp, 350 mva 54 11 kv vcb i / c ctr 600 / 300 / 5amp 55 3 phase distribution box 56 33 kv control panel i / c single tf 57 construction of 250 / 400 kva t / f plinth all cost of labour and t&p which required for completion of work 58 net fencing shall be 1150*1200 mm made of 35*35 mm ms angle covered by expended netal 14 swg up to full height 1200 mm duly steftened by ms flat by an 8 swg dia bolt & nut 59 pipe earthing of 250 / 400 kva medium power transformers 60 33 kv vcb outgoing ct 400 / 200 / 5a 61 33 kv ct, o / g 400 / 200 / 1amp 62 11 kv ct o / g 400 / 200 / 5amp 63 11 kv ct i / c 600 / 300 / 5amp 64 33 kv lighting arrestor 65 33 kv fuse set 66 danger board with barbed wire including jumpering 67 dead end clamp 68 stone pad 69 fixing / erection oflt incoming pannel with metering equiptment, grouting as per respoo manual all cost of labor, material and t&p which required for completion of work 70 tripping coil for vcb 71 lt production for dt ( mccb ) 72 lt production for dt 73 4 core lt mcb with box 74 alluminium paint 75 red oxide paint 76 33 kv cable jointing kit outdoor 3x300 sqmm 77 33 kv cable straight through outdoor 3x300 sqmm 78 erection and grouting of stays as per respo norms and as per direction of supervising engineer. grouting material i.e. cement, sand, brick ballast / stone ballast etc. shall be arranged by the contractor at his own cost. 79 any other material / consumable required to complete the work shall be arrange by the contractor at his own cost. 80 carriage of old line material from pit site to je store / store center etah in distance range 0 to 10 km. including loading & unloading and proper stacking. 81 ( a ) 11 kv vcb 82 ( b ) 33 kv control panel...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39844018 various electrical work of electric supply in the area of eudsd ist, etah ( eudd, etah ) under additional business plan ( 339 cr. ) on semi turnkey basis. 2 danger board with barbed wire including jumpering 3 dead end clamp 4 holding clamp for top chanel 5 i hook 6 lt pin clamp for pcc 7 ms droper chanel 8 ms top chanel with clamp 9 nut and bolt with washer 10 stone pad 11 suspension clamp 12 lt incoming panel with metering equipment 13 copper l piece 14 alluminium lug 15 alluminium paint 16 red oxide paint 17 tf base angle 18 prc connector 19 t chanel chanel clamp 20 t chanel 21 tripping coil for vcb ( areva ) 22 tripping coil for vcb ( stelmac ) 23 lt protection for dt ( mccb ) 24 lt protection for dt 25 dc converter with battery 26 erection work : 27 safe carriage of line material from store center etah to pit site in distance range 0 to 10 km including loading & unloading at both ends. 28 safe carriage of33 kv vcb from store center etah to pit site in distance range 0 to 10 km including loading & unloading at both ends. 29 ( a ) 11 kv vcb outgoing / incoming 30 ( b ) 33 kv vcb 31 safe carriage of33 kv / 11 kv ct from store center etah to pit site in distance range 0 to 10 km including loading & unloading at both ends. 32 safe carriage of 8.5 mtr long pcc pole from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 10 kms.including loading and unloading at both side 33 safe carriage of 11 mtr long st pole from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 10 kms.including loading and unloading at both side 34 safe carriage of following tf from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side. 35 ( a ) 250 / 400 kva tf 36 ( b ) 100 kva tf 37 ( c ) 16 kva tf 38 erection of 8.5 mtr long pcc pole as single support including fixing of ht / lt accessories etc and other work complete as per respo norms. 39 erection of 11 mtr long st pole as single support including fixing of ht / lt accessories etc and other work complete as per respo norms. 40 erection of 11 mtr long st pole as double pole including fixing of ht / lt accessories with tpmo etc and other work complete as per respo norms. 41 mounting of following tf on double pole / single pole including making of the connection etc. complete. 42 ( a ) 250 / 400 kva tf 43 ( b ) 100 kva tf 44 ( c ) 16 kva tf 45 laying sagging stringing, binding, jumpering & fixing of all accessories etc of following conductor on the newly / old erected pole as per respo manual and as per direction of supervising engineer. it includes the cost of labour, t & p, carrier etc required for proper completion of work. 46 ( a ) acsr weseal conductor 47 ( b ) lt abc cable 3x120 sqmm 48 ( c ) lt abc cable 3x95 sqmm 49 ( d ) lt pvc al cable 3.5x150 / 3.5x400 sqmm 50 ( e ) cable 4x2.5 sqmm 51 earthing complete 52 11 kv vcb o / g ctr 200 / 100 / 5amp, 350 mva 53 11 kv vcb i / c ctr 600 / 300 / 5amp 54 3 phase distribution box 55 33 kv control panel for double tf 56 construction of 250 / 400 kva t / f plinth all cost of all cost of labour and t&p which required for completion of work 57 net fencing shall be 1150*1200 mm made of 35*35 mm ms angle covered by expended netal 14 swg up to full height 1200 mm duly steftened by ms flat by an 8 swg dia bolt & nut 58 pipe earthing of 250 / 400 kva medium power transformers 59 33 kv vcb 800 amp, 750 mva 60 33 kv ct, 400 amp / 200 / 1 1 1 amp 61 11 kv ct i / c 600 / 300 / 5amp 62 11 kv ct o / g 400 / 200 / 5amp 63 33 kv lighting arrestor 64 33 kv fuse set 65 danger board with barbed wire including jumpering 66 dead end clamp 67 stone pad 68 fixing / erection oflt incoming pannel with metering equiptment, grouting as per respoo manual all cost of labor, material and t&p which required for completion of work 69 tripping coil for vcb ( areva ) 70 tripping coil for vcb ( stelmac ) 71 lt production for dt ( mccb ) 72 lt production for dt 73 4 core lt mcb with box 74 single core pvc cable 1x240 75 single core pvc cable 1x400 76 single core pvc cable 1x630 77 erection and grouting of stays as per respo norms and as per direction of supervising engineer. grouting material i.e. cement, sand, brick ballast / stone ballast etc. shall be arranged by the contractor at his own cost. 78 any other material / consumable required to complete the work shall be arrange by the contractor at his own cost. 79 carriage of line material ( scrap ) from pit site to je store / store center etah in distance range 0 to 10 km. including loading & unloading and proper stacking. 80 ( a ) 11 kv vcb outgoing 81 ( b ) 10 kva transformer ( old ) 82 ( c ) 100 kva transformer ( old ) ...

Yamuna Expressway Industrial Development Authority - Uttar Pradesh

39831997 tender for repairing of kerb stone & painting of 60mtr wide road ch.7.10 to 22.300km along yamuna expressway, yea wc 01: tender for construction of balance boundary wall of primary school in viiage bagmabad yea wc 06: tender for construction of classrom varandah toilet and pathways of primary school in village wailana yea wc 06: tender for pond rejuvention in village dankaur year wc 06: tender for r.c.c pipe drain laying work pond 01 to 02 & 03 drain in village ahmadpur choroli yea wc 06: tender for construction boundary wall of parks near plot no 304 & 139 pocket 3d sector 18 yea wc horti: tender for construction boundary wall of parks near plot no 307 & 105 pocket 3a sector 18 yea wc horti: tender for maintenance & repair work of 30mtr and 45mtr wide road in sector 22d yea wc 02: tender for p/o trees shrubs and lawn including barbed wire fancing of 50mtr wide green belt & 30mtr road central verge parallel to expressway infront of ats allure society sec 22d with two year maintenance for yea. wc horti: tender for jungle cleaning work at moto gp parking no 2 in sector 17a & p&f direction board in different locatin in yeida wc 06: tender for providing and laying retro reflective thermoplastic paint at 60mtr wide road from ch.7.10km to 12.500km yea wc 01: tender for jungle cleaning work at moto gp parking no 1 & barricading work in sector 17ayea wc 01: tender for providing & fixing stone (repair & new work) road (ch.10.65km to 12.87km) along yamuna expressway yea wc 03: tender for jungle cleaning work of hollage roade for all gate entry & garbage cleaning work at 60.0mtr wide road yea wc 01: tender for laevlling & dressing of moto plot parking no 1 & 2 in sector yea wc 01: tender for road marking at 30.00mtr wide road (ch.14.35km to 16.10km) along yamuna expressway yea wc 03: tender for road marking at 30.00mtr wide road (ch.16.10km to 17.45km) along yamuna expressway yea wc 03: tender for providing & fixing kerd stone (repair & new work) road (ch.12.87 km to 17.45km) along yamuna expressway yea wc 03: tender for kerb stone painting and maintence of 30mtr wide road ch.7.10km to 10.30km along yamuna expressway yea wc 04: tender for bituminious work (bc) on 30mtr wide road (under eastern peripheral) along yamuna expressway yea wc 04: tender for providing & fixing and repairing kerb stone and maintenance of patri of 30mtr wide road ch.7.10km to 10.30km along the first expressway is wc 0: tender for road marking at 30.00mtr wide road (ch.12.55km to 14.30km) along yamuna expressway yea wc 03: tender for patch repair of 30.00mtr wide road (ch.17.00km to 17.45km) along yamuna expressway yea wc 03: tender for supply & laying of good earth at 30..00mtr wide road (ch.10.65km to 17.45km) along yamuna expressway yea wc 03...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39812845 under the additional business plan 2023 24 work received from electricity distribution division ii mitouli, replacement of 11 kv bcb in sub centre kamhara and construction of 33 kv new line under sub centre kalakam ( semi turnkey based work / decentralized all material executing agency ) the work will be payable by ) . 1 safe loading carriage including unloading and proper stacking of following materials from store center / je store to site of work and old dismentling material to store center / je store. 2 11kv outgoing vcb 200 / 100 / 5a 3 11kv incoming vcb 600 / 300 / 5a 4 11kv jointing kit 3x185 sq. mm xlpe hs i / d 5 installation of vcb as per respo norms and dismentling of old 11kv vcb at 33 / 11kv sub station kaimahra. 6 making delta earthing 7 safe loading carriage including unloading and proper stacking of following materials from store center / je store to site of work and old dismentling material to store center / je store. 8 stay set gi 30x1800 mm 9 11kv disc insulator ( b&s ) 70kn 10 steel tubler pole11mrt. long. 11 acsr dog conductor. 12 earth wire 7 / 16 swg 13 disc fitting for dog. 14 barbed wire. 15 g.i. pin 33kv with nut & bolt. 16 stay wire gi ( 7 / 4 mm ) 7 / 8 swg 17 33 kv v type cross arm 18 earth rod 2540x20mm 19 stay clamp for 11mtr. long stp 20 pin insulator 33kv 21 construction of 33kv overhead new line with all accessries under work are of 33 / 11kv sub station kala aam. as per approved estimate. 22 supply of holding clampr for st pole. 23 supply of aluminium paint.with work of 24 supply of ms top channel ( 125x65mm ) 2240mm long. 25 suppy of f bracket for 33kv line size 75x10mm. 26 supply of 33kv bracing angle. 27 supply of danger borard with clamp for 33kv line. 28 supply of red oxide paint. 29 supply of p.g. clam [ for dog to dog conductor. 30 grouting of stay. 31 grouting of stp pole. 32 supply of stay loop insulator. 33 supply of stone pad. 34 supply of nut & bolt....

Village Panchayat - Uttar Pradesh

39812069 tender for provide of construction material cement, balu, sand, bajri, brick, blast, interlocking tiles, wall tiles, fursh tiles, rod, iron jali, soil, wall painting, sanitary equipment, electric equipment, iron fencing wire, iron angle, furniture bench, cement concrete bench, dustbin, street led light, barbed wire, paint, primer, toilet sheet, handpump repairing equipment, rcc pillar, pvc pipe, water storage tank, ply board, running water supply equipment, iron gate, iron sheet, mike sheet....

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39811994 carrying out the 04 nos. work increasing capacity / 02 nos. work construction of 11 / 0.4 kv s / s under eudd v / vii, noida respectivly in the juridiction of eudc i, noida ( total 06 nos. work in additional business plan rs. 30.00 crore for noida zone ) . 1 following 04 nos. work increasing capacity/ 02 nos. work construction of 11/0.4 kv s/s at various places under eudd v/vii, noida respectivly : 2 cartage of st poles 11 mtr long from esc noida/sahibabad/ ghaziabad /any other esc of meerut discom to je store and from je store to site of work including loading and unloading at both ends. 3 cartage of other line material such as 11kv disc insulator t&c type 4500 kg. (36 nos.), 11kv disc fitting (36 nos.), 11 kv pin insulator (42 nos.), 11 kv pin with nut (42 nos.), acsr dog conductor (640 mtrs.) etc. from esc noida/sahibabad/ghaziabad /any other esc of meerut discom to je store and from je store to site of work including loading and unloading at both ends. 4 cartage of lt abc 3x120+1x95+1x16 sq.mm. from esc noida/sahibabad/ ghaziabad /any other esc of meerut discom to je store and from je store to site of work including loading and unloading at both ends. 5 the excavation of foundation pit in cc road/ mix soil/ normal soil/ soft & hard rack by using heavy duty compressor and its back filling and leveling etc. the size of the pit will be 600x600x1800 mm for each pole and having a depth of 1/6 of the full length of the support. 6 erection of double pole on 11 mtr. long st pole for lt line including fixing of all accessories of lt line as per respo schedule complete in all respects. 7 erection of pole on 11 mtr. long st pole for lt line including fixing of all accessories of lt line as per respo schedule complete in all respects. 8 grouting of each pole (in ratio of 1:4:8 in cement, sand and brick ballast) in size 450mmx450mmx1800 mm as per respo schedule complete in all respects. 9 construction of plinth in size 450x450x300 mm of each (0.880 cu.m.each) pole above the ground level(in ratio of 1:3:6 in cement, sand and brick ballast) as per respo schedule complete in all respects. 10 erection of pole on 11 mtr. long st pole for lt line including fixing of all accessories of lt line as per respo schedule complete in all respects. 11 laying, lifting and final binding, sagging of acsr dog conductor including fixing of all accessories as per respo schedule complete in all respects. 12 laying, lifting and final binding, sagging of lt abc 3x120+1x95+1x16 sq.mm. including fixing of all accessories as per respo schedule complete in all respects. 13 providing & fabrication / fixing of following material of best quality for completion of work as per site requirement : 14 11 kv tpmo 15 11 kv fuse set 16 lt pvc cable al. 3.5x240 sq.mm.(laying of cable including fixing of all accessories as per respo schedule complete in all respects.) 17 stay set 16x1800 mm(grouting & concreting of stay rod 1800x16 mm complete in all respect as per respo schedule complete in all respects.), (fixing, tighting and nozzling of stay wire 5 kg with the pole of required tension with clamps, bolt & nut as per respo schedule complete in all respects.) 18 ms earthing rod (2540x20 mm) complete(excavation of earth and driving of m.s. earthing rod of size 20x2540 mm in earth and jointing through g.i wire of 6 swg between support and earth electrode by providing proper size of bolts and nuts etc. as per respo schedule complete in all respects.) 19 ms dropper channel 100x50x2028mm 20 stone pad 300x300x75 mm 21 clamp for lt (t off) with bolt and nuts 22 ms top channel 125x65x2240 mm 23 ms channel 125x65x1300mm (t off) 24 al. lug long barrel, off size (ls) 25 holding clamp for top channel, tpmo and fuse set etc with bolt and nuts. 26 11 kv v type cross arm 27 lt pvc cable al. 1x400 sq.mm.(laying of cable including fixing of all accessories as per respo schedule complete in all respects.) 28 danger board, barbed wire including jumper 29 red oxide paint 30 aluminium paint 31 st pole clamp 32 f clamp for pin insulator with nut & bolt 33 3 phse distribution box 34 lt piercing connector for size 120/95 35 clamp for distribution box with nut & bolt 36 lt 1x70 sq.mm. lead(laying of cable including fixing of all accessories as per respo schedule complete in all respects.) 37 construction of new distribution 250 kva t/f plinth. the size of plinth shall be 2 mtrs. long, 2 mtrs. wide and height 1.5 mtrs. from ground level with 15 cm thick top cc slab. the above work includes excavation of earth, laying of bring ballast pad for foundation brick work, cc and plastering and proper curing complete with all respects as per respo schedule. 38 safe loading and carriage of 250 kva transformerfrom esc noida/sahibabad/ ghaziabad /any other esc of meerut discom to je store and from je store to site of work including loading and unloading at both ends 39 mounting, installation of 250 kva transformer on above plinth, alongwith double earthing of the same, complete in all respect as per respo schedule. 40 panel fabrication of size 1250mm x 900mm x 600 mmmade of m.s sheet 14 gauge with powder coating with panel lock and key arrangement.(two nos). and additional locking arrangement seprately including providing hut type shape as per drg. 41 providing and installation oflt acb600 amp. with cabinet / structure (make l&t, schneider, abb, hevells) as per following specification with all relevant certificate : 42 600 amp. 03 pole fixed manual acb. 43 red/yellow/blue light indication 44 on & off indication 45 amp., voltmeter& energy meter digital 46 metering c.t 600/5a, 47 panel fabrication of size 1250mm x 900mm x 600 mmmade of m.s sheet 14 gauge with powder coating with panel lock and key arrangement.(two nos). and additional locking arrangement seprately including providing hut type shape as per drg. 48 fabrication ofaluminium bus bar for each phases 49 incoming size 425 mm x 50mmx12 mm (twin) 50 out going size 720 mm x 50mm x 12 mm(twin) 51 neutral size 900mmx50mmx12 mm. 52 fabrication of pannel stand made of m.s angle of size 900mm x 600mm x 500 mm as per drg. 53 assembly of above acb, indicators, meters, metering ct & bus bar arrangment in the panel, fitting the panel on stand with nut and boltswith wiringetc. & grouting inratio 1:4:8 with cement, coarse sand and brick blast. 54 providing and fixing of aluminium bus bar of size 300mmx60mmx12 mm on l.t side of t/f. 55 making all connections with acb & distribution t/f and commissioning the acb complete in all respect. 56 providing and installation of chemical earthing for 250 kva transformers (body & neutral) and acb (with all material and labour) after installation resistance should be less than one ohm. as per following (the all material and labour shall be provided by the contractor with 12 month guarantee for resistance value less than one ohm.) : 57 providing of earth elctrode for chemical earthing pipe in pipe typeproper hot deep galvanization dia 50 mm length 3 mtr 32mm x 6mmterminal connection hole dia 8mm the cavity between the pipe & pipe is filled with conductive mixture for hermetically filling inside the cavity i.e. between secondary conductor & primary conductor, crystalline compound is to be injected in the electrode assembly. it is a combination of high conductivity metal alloys, copper & aluminum power, conductive carbon / cement and bonding material etc the electrode should be sealed from both the ends. the outer pipe of the elctrode should be galavanized the characteristics of this compound is highly cnductive, non magnetic & non corrosive in g.i. including providing of backfill compound each elctrode should be supplied with bags of 25 kg x 2 bfc compound (ground resistance enhancement powder 50 kgs each cpri tested for 250 kva distribution t/f & acb installed at above 11/0.4 kv l.t. substation. 58 providing and fixing of gi strip of size 32 mm x 6 mm suitable for 250 kva distribution t/f & acb installed at above 11/0.4 kv l.t. substation. 59 providing and fixing of pvc pit covers for above earthing electrode terminals. 60 work of providing and fixing of 06 nos. new wiremesh fencing of 11/0.4 kv l.t. sub station installed at above place as per following : 61 providing & fixing of new wiremesh fencing frames of size 12x15x6for each fencing of lt sub stations.) (all material provided by contractor for above work.) 62 construction of boundry / toe wall in bottom of fencing in brick work cement mortar 1:6 (1 cement : 6 coarse sand) for link in the size of 0.22mx0.60m (0.30m in earth, 0.30m above ground level) including plaster in cement mortar 1:4 and finishing with water proof cement paint. (approx construction 12 mtrs. boundry / toe wall for each fencing of lt sub stations.) (all material provided by contractor for above work) ...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39811304 tender for various electrical work of electric supply in the area of edsd vth, etah ( edd iind, etah ) under additional business plan ( 339 cr. ) on semi turnkey basis. 1 supply of the line material as per relevent iss : 2 holding clamp for tf 3 nut & bolt with washer 4 stone pad 5 danger board 6 barbed wire 7 top channel 8 ms angle with clamp 9 pg clamp 10 clamp with nut & bolt 11 33 kv cable jonting kit o/d 3x300 sqmm 12 33 kv cable jonting kit i/d 3x300 sqmm 13 erection work : 14 safe carriage of line material from store center etah to pit site in distance range 0 to 60 km including loading & unloading at both ends. 15 safe carriage of following vcb from store center etah to pit site in distance range 0 to 60 km including loading & unloading at both ends. 16 11 kvvcb 17 33 kvvcb 18 safe carriage of 33 kv xlpe cable 3x300 sqmm from store center etah to pit site in distance range 0 to 60 km including loading & unloading at both ends. 19 safe carriage of 8.5 mtr long pcc pole from electricty store center etah/nearest 33/11 kv s/s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side 20 safe carriage of 13 mtr long st pole from electricty store center etah/nearest 33/11 kv s/s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side 21 safe carriage of 10 kva tf from electricty store center etah/nearest 33/11 kv s/s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side. 22 erection of 8.5 mtr long pcc pole as single support including fixing of ht/lt accessories etc and other work complete as per respo norms. 23 erection of 13 mtr long st pole as double pole/section pole including fixing of ht/lt accessories etc and other work complete as per respo norms. 24 dismantling and removal of existing acsr weasel/dog conductor conductor from the various area, stacking and placement their coils and their in the safer place including cost of lobour t&p etc. required for proper completion of work. 25 laying sagging stringing, binding, jumpering & fixing of all accessories etc of following conductor on the newly/old erected pole as per respo manual and as per direction of supervising engineer. it includes the cost of labour, t & p, carrier etc required for proper completion of work. 26 (a) acsr weseal conductor 27 (b) acsr dog conductor 28 (c) 33 kv xlpe cable 3x300 sqmm 29 (d) lt ab cable 3x50 sqmm 30 re sagging of looseweseal/dog conductor as per direction of supervising engineer. it includes the cost of labour, t & p carrier etc required for proper completion of work. 31 stone pad 32 pg clamp 33 earthing complete 34 33 kv vcb 800a, 750 mva 35 making of 33 kv vcb double tf control panel nct 200/100 1amp with structure as per respo norms. 36 11 kvvcb o/g ctr 200/100/5a, 350 mva 37 33 kv cable jonting kit o/d 3x300 sqmm 38 33 kv cable jonting kit i/d 3x300 sqmm 39 danger board with clamp 40 erection and grouting of stays as per respo norms and as per direction of supervising engineer. grouting material i.e. cement, sand, brick ballast/stone ballast etc. shall be arranged by the contractor at his own cost. 41 mounting of 10 kva tfincluding making of the connection etc. complete. 42 any other material/consumable required to complete the work shall be arrange by the contractor at his own cost. 43 carriage of acsr dog/rabbit/weseal conductor (scrap) from pit site to je store/store center etah in distance range 0 to 60 km. including loading & unloading and proper stacking. ...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39811207 various system strengthening works under the jurisdiction of e.e, eudd residency, lesa cis gomti lucknow. 1 safe carriage, loading unloading with proper stacking of following materialfrom esc daliganjto work site/je dump store 2 11kv3x70/185 sq mm xlpe cable 3 11kvend termination o/door & i/door 3x70/185 sq mm 4 11/0.4 kv 400/630 kva t/f 5 lt xlpe cable 1x400/630/3.5x400 sqmm 6 st pole 9 mtr long 7 abc (3x120+1x95+1x16) sqmm 8 polymeric pin insulator 9 fabrication & erection of s/s type double pole for 11kv line on 11 m long st pole with fixing of necessary clamps & other accessories like 1 no. top channel 100×50 mm,2 no.ms angle 65x65x6mm,danger board, number plate, barbed wire, tpmo set & d.o. fuse set. 10 construction of t/f plinth of size 2x2x1.5 m on a padding 0.25m deep in ground 1:5:10 cement sand and brick ballast on the top of padding brick work ist class brick of 0.95 mtr height & 0.35 mtr wall will be constructed. rest wall should be 0.23 mtr thick. brick work in ratio 1:4 cement & cores sand in the hollow portion the sand should be filled from the ground level up to 15 centimeter below from the top of wall, cement, sand & brick ballasts should be filled up to 15 centimeter. two no. of channel 100x50 in length 1500mm will be grouded.0.35 cm.rcc will be done with cores sand, cement and stone ballast in the ratio of 1:2:4.the t/fs plinth should be plastered on all sides 12mm thick in ratio 1:6 by cement and cores sand. (all the material will be arranged by the contractor .) 11 construction of retaining wall, fabrication & erection of wire mesh fencing around transformer and distribution pillar box with retaining wall & 1 no. gate with locking arrangement made of ms angle iron of size 50x50x6 mm jointed with nuts and bolts. the panel must be supported with ms flat of size 50x6 mm.wiremesh of size 10 swg rectangle type, its painting as per norms of resspo.(all the material will be arranged by the contractor at his own cost). 12 construction of massonary type distribution pillar box with first class brick ballast cement, coarse sand, local sand, brick ballast and ms round bar of 10 mm dia including straight ms angle 50x50x6x750 mm (all the material will be arranged by the contractor). 13 supply & fixing of henless fuse unit 500 amp 650 volts 14 s/c cable laying in normal soil by digging of trench 900 mm deep, 500 mm wide including supply of required material as fine sand, 1st class bricks, stone slab. (all the material required for laying will be supplied by the contractor except 11 kv xlpe cable) 15 d/c cable laying in normal soil by digging of trench 900 mm deep, 500 mm wide including supply of required material as fine sand, 1st class bricks, stone slab. (all the material required for laying will be supplied by the contractor except 11 kv xlpe cable) 16 supply & fixing of cu l piece for 400/630 kva t/f 17 supply & installation of d.o fuse set 18 hoisting, winding and jumpering of lt cable size 1x400/630/3.5x400 sqmm between lt distribution box/fuse unit & constructed overhead line with proper lugging and clamping 19 stringing, sagging, winding and jumpering of lt line with ab cable (3x120+1x95+1x16) conductor as per resspo norms. (ab cable provided by deptt and balance material like holding clamp,eye hook, suspension clamp and dead end clamp arranged by contractor .) 20 supply of 11 kv rmu (three way rmu (2lbs + 1cb) as per t.s/ approvedmvvnl gtp) 21 hoisting of 11kv xlpe cable/rmu of 3x70/185 sq mm cable 22 chemicalearthingsystemwithouterpipe diameter50mm,innerstrip40x6,length3000 mm. galvanization up to 200 micro, earthing pipe withcrystallineconductivemixturefilledinside thepipewithanti corrosion&highconductive alongwith50kg(as perrequired) ofbfc which should be capable to reducing the soil resistively with good moisture retaining capacity.(specificationofchemicalearthingand drawing is hereby enclosed). all material shall by supply by the contractor. 23 providing earthing strip size 50x6mm and connecting from earthing pipe/m.s.earting rod to fuse unit/transformer body/ neutral earthing (earthing rod & earthing strip arranged by contractor). 24 installation of 11/0.4 kv 400/630 kva t/f (by crane) 25 installation of rmu including grouting & plinthing 26 wiremesh fencing for rmu 27 removal of connections from the system, safe loading carriage unloading of damaged t/f from site to store centre daliganj/ transformer repair workshop, aliganj 28 400 kva transformer by tractor trolley/crane) 29 groutingofpoleindepthof1/6thelengthof poleinratio 1:4:8incementsandandbrick balast as per respo norms. 30 construction of pole plinth 300mm x 450 mm above ground level in 1:2:4 in cement, coarse sand and stone gritt as per respo norms. 31 painting of new erected st pole with two coat of red oxide paint,po red paint at top of pole 2 m & balance by two coats of best quality aluminium paint isi of burger/nerolac/asian mark as per norms. 32 taping of line 33 supply and fixing of copper strip of size 1000x50x6 mm 34 fixing of earth rod (2500x20mm) as per norms. for earthing support ofold existing poles of lt lines including 6 swg gi/earth wire . (all materials provided by contractor) ...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39811123 various system strengthening works under the jurisdiction of e.e, eudd residency, lesa cis gomti lucknow 1 safe carriage, loading unloading with proper stacking of following materialfrom esc daliganjto work site/je dump store 2 11kv3x70/185 sq mm xlpe cable 3 11kvend termination o/door & i/door 3x70/185 sq mm 4 11/0.4 kv 400 kva t/f 5 lt xlpe cable 1x400/3.5x400 sqmm 6 st pole 9 mtr long 7 polymeric pin insulator 8 abc (3x120+1x95+1x16) sqmm 9 supply of 11 kv rmu (three way rmu (2 lbs + 1cb) as per t.s/ approvedmvvnl gtp) 10 hoisting of 11kv xlpe cable/rmu of 3x70/185 sq mm cable 11 fabrication & erection of s/s type double pole for 11kv line on 11 m long st pole with fixing of necessary clamps & other accessories like 1 no. top channel 100×50 mm,2 no.ms angle 65x65x6mm,danger board, number plate, barbed wire, tpmo set & d.o. fuse set. 12 s/c cable laying in normal soil by digging of trench 900 mm deep, 500 mm wide including supply of required material as fine sand, 1st class bricks, stone slab. (all the material required for laying will be supplied by the contractor except 11 kv xlpe cable) 13 construction of t/f plinth of size 2x2x1.5 m on a padding 0.25m deep in ground 1:5:10 cement sand and brick ballast on the top of padding brick work ist class brick of 0.95 mtr height & 0.35 mtr wall will be constructed. rest wall should be 0.23 mtr thick. brick work in ratio 1:4 cement & cores sand in the hollow portion the sand should be filled from the ground level up to 15 centimeter below from the top of wall, cement, sand & brick ballasts should be filled up to 15 centimeter. two no. of channel 100x50 in length 1500mm will be grouded.0.35 cm.rcc will be done with cores sand, cement and stone ballast in the ratio of 1:2:4.the t/fs plinth should be plastered on all sides 12mm thick in ratio 1:6 by cement and cores sand. (all the material will be arranged by the contractor .) 14 construction of retaining wall, fabrication & erection of wire mesh fencing around transformer and distribution pillar box with retaining wall & 1 no. gate with locking arrangement made of ms angle iron of size 50x50x6 mm jointed with nuts and bolts. the panel must be supported with ms flat of size 50x6 mm.wiremesh of size 10 swg rectangle type, its painting as per norms of resspo.(all the material will be arranged by the contractor at his own cost). 15 construction of massonary type distribution pillar box with first class brick ballast cement, coarse sand, local sand, brick ballast and ms round bar of 10 mm dia including straight ms angle 50x50x6x750 mm (all the material will be arranged by the contractor). 16 supply & fixing of henless fuse unit 500 amp 650 volts 17 chemicalearthingsystemwithouterpipe diameter50mm,innerstrip40x6,length3000 mm. galvanization up to 200 micro, earthing pipe withcrystallineconductivemixturefilledinside thepipewithanti corrosion&highconductive alongwith50kg(as perrequired) of bfc which should be capable to reducing the soil resistively with good moisture retaining capacity.(specificationofchemicalearthingand drawing is hereby enclosed). all material shall by supply by the contractor. 18 supply & fixing of cu l piece for 400/630 kva t/f 19 supply & installation of d.o fuse set 20 hoisting, winding and jumpering of of lt cable size 1x400/3.5x400 sqmm between lt distribution box/fuse unit & constructed overhead line with proper lugging and clamping 21 stringing, sagging, winding and jumpering of lt line with ab cable (3x120+1x95+1x16) conductor as per resspo norms. (ab cable provided by deptt. and balance material like holding clamp,eye hook, suspension clamp and dead end clamp arranged by contractor .) 22 providing earthing strip size 50x6mm and connecting from earthing pipe/m.s.earting rod to fuse unit/transformer body/ neutral earthing(earthing rod & earthing strip arranged by contractor). 23 installation of rmu including grouting & plinthing 24 wiremesh fencing for rmu 25 installation of 11/0.4 kv 400 kva t/f (by crane) ...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39810761 boq for increasing of different distribution transformers at different places, installation of new transformer and guarding / construction of new line in the area of e.u.d.d. aishbagh under jurisdiction of e.u.d.c.iii, lesa cis gomti, lucknow against additional business plan 2023 24 1.00 safe carriage, loading and unloading of following material from esc daliganj, lucknow to work site/j.e. dump store. 1.01 11/0.4 k.v. 400 k.v.a. transformer. 1.02 11/0.4 k.v. 630 k.v.a. transformer. 1.03 s.t. pole 11 mtr. long. 1.04 11 k.v. 3x120 sq.mm. xlpe cable. 1.05 o/d jointing kit for 11 k.v. 3x120 sq.mm. cable. 1.06 abc (3x120+1x95+1x16 sq.mm.) 1.07 11 k.v. g.i. pin with pin insulator & nuts. 1.08 m s angle 65x65x6 mm. (9.8 kg.) 1.09 m s channel 100x50 mm. 1.10 acsr weasel conductor. 1.11 g.i. wire (8 swg) 2.00 fabrication, erection of double pole structure on 11 mtr. long stp with necessary clamps, accessories required including fixing of top channel 125x65x6 mm. (2240 mm long) 01 nos., dropper channel 100x50 mm. (2028 mm long) 01 nos. with arrangment of fixing of 06 nos. 11 k.v. pin insulators. cross bracing set of ms angle 01 nos. grouting of 02 nos of stp with cement, sand and brick ballast in ratio 1:4:8 (2x0.9 cu.mtr) and making plinth upto the height of 300 mm from ground. painting of poles with primer and enamel paint as per respo specification complete in all respect. providing danger board, name plate & barbed wire. earthing of both the poles. 3.00 construction of masonary plinth suitable for 400 k.v.a. transformer of size 2x2x1.2 mtrs with complete civil material & 02 nos.,100x50 mm, m.s channel 2.0 mtr. long and m.s bar 8/10 swg complete in all respect as per respo norms. 4.00 repairing of masonary type plinth of various distribution transformers installed in the area, along with all the material required. shifting of the various distribution transformers and after completion of repairing work, replacing the distribution transformers with the help of crane. 5.00 fabrication and erection of wire mesh fencing 02 mtr. height with a gate and with retaining wall including grouting of fabricated m.s. angle 65x65x6 mm. support (05 nos. in a sub station). painting of fencing/support with all material as per specification/drawing complete in all respect. 6.00 repairing and painting of the damaged wiremesh fencing of l.t. sub stations in the area, along with all the required materials. 7.00 construction of masonry type d.p. box with 02 nos. 500/300 amp. tabular fuse unit and m.s. angle iron support of size 50x50x6 mm. all the civil and other material required shall be arranged and provided by contractor for completion of job as per respo norms along with necessary laying of cable and its cartage & necessary connections. 8.00 disconnection of existing 250 kva transformer from system shifted upto safe place to the nearest 33/11 k.v. sub station of division or required place. 9.00 disconnection of existing 400 kva transformer from system shifted upto safe place to the nearest 33/11 k.v. sub station of division or required place. 10.00 placing of 400 k.v.a. healthy transformer from out side of yard to plinth with the help of crain and t & p. 11.00 placing of 630 k.v.a. healthy transformer from out side of yard to plinth with the help of crain and t & p. 12.00 ab conductor stringing & sagging of 3 phase with necessary clamps, eye hook, suspension clamp, a b type connector etc. on abc new line as per respo specification and direction on e/i. abc shall be supplied by department. 13.00 laying of 11 k.v. xlpe cable 3x120 mm2 in underground as per digging of earth pit of size 0.60x0.90 with provision of sand filling and cover with side brick and top with stone pad. (11 k.v. xlpe cable will be provided by deptt. only) 14.00 hoisting of 11 k.v. xlpe cable 3x120 mm2. along with 5 dia g.i. pipe 03 meter long with required clamp etc. 15.00 stringing & sagging of 3 phase 3 wire 11 k.v. new line on acsr weasel conductor as per respo specification and direction on e/i. conductor shall be supplied by department. 16.00 stringing and sagging of g.i. wire for guarding and earthing under existed 11 kv o/h line with clamps, nuts & bolt existing under various feeder under consirning s/s. (only g.i. wire 6 swg will be provided by deptt) 17.00 earthing of 11/0.4 k.v distribution transformer body/neutral by way of boring and lowering of isi marked two nos. g.i pipe 1.5 dia 20 m deep from the ground level with solid cone at the lower end of g.i pipe. one end of g.i strip of size 50x6 mm. will be connected with neutral and body of the transformer & other end will be clamped & welded with g.i pipe as per uppcl norms (all the material will be arranged by contractor at their own cost.) ...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39810410 work of full deposit scheme in mla fund at various places under subdivision i / ii, medical / kithor in the jurisdiction of university of secondary education iv, meerut. 1 cartage of following material from store center to site of work including loading & unloading at both ends maximum distance up to 40 km. : 2 st pole 11 mtr.long. 3 pcc pole 8.5 mtr. long. 4 acsr weasal conductor. 5 ab conductor ( 3x95+1x70+1x16 ) sq.mm. 6 ab conductor ( 3x120+1x95+1x16 ) sq.mm. 7 11 kv xlpe cable 3x120 ( 170x1 ) +15 mtr 4 sag. 8 11 kv jointing kit 3x120 sq.mm. 9 lt xlpe cable 1x240 sq.mm. 10 distribution box 3 phase. 11 pvc lead. 12 63 kva t / f. 13 250 kva t / f 14 line material such as 11 kv cross arms 11 kv pin, 11 kv pin insulator, 11 kv disc, stay rod, stay wire, gi wire, top channel, fuse set, dropper channel, ms angle iron & ms channel etc. 15 erection of pcc pole 8.5 mtr long / stp pole 11 mtr long after digging a pit of size 1.20x0.60x1.6 mtr in all type of soil including back filling of the pole with proper ramming after completion of work. 16 fabrication and fixing of all 11 kv ht / lt line. 17 making a section pole to exist pole jumpring of ht side and all 11 kv accessories. 18 erection of stay rod complete after digging a pit of size 1.20x0.60x1.6 mtr and grouting the same in block of size 0.60x0.60x0.30 mtr and nuzzling at the both ends and filling the pit with excavated earth soil with proper ramming. 19 laying lifting stringing of proper sagging of acsr weasal conductor for 3 phase, 3 wire 33 kv line including binding & jumpering properly. 20 11 kv xlpe cable 3x120 ( 170x1 ) +15 mtr 4 sag. 21 lt xlpe cable 1x240 sq.mm. 22 installation of distribution box 3 phase. 23 dissmentling of rail pole by digging the pits & removel of complete ht / lt line accessories for double pole. 24 dissmentling of acsr weasal conductor removal of complete ht / lt line accessories. 25 mounting of 63 kva t / f on double pole. 26 making of plinth 250 kva t / f of size 6x6x3 ( feet ) . 27 wiremesh fencing for 250 kva t / f. 28 water level earthing for 250 kva t / f. 29 mounting of 250 kva t / f on plinth with help of hydra. 30 making of double pole 63 / 250 kva t / f 31 grouting pcc 8.5 mtr. long / stp pole 11 mtr long as per respo. 32 providing and fixing of stone pad. 33 providing and fixingstay clamps. 34 providing and fixing holding clamps. 35 providing stay insulator. 36 providing and fixing bolts and nuts. 37 concreting with stay set. 38 providing danger board with clamp. 39 providing of number plate. 40 providing of barbed wire. 41 earthing set complete....

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39810349 electricity distribution division nataki marginal electricity details sub rad ( 1 ) 33 / 11 k.b. work of installing dog conductor in place of dilapidated fan duct in the power substation ( 2 ) 33 / 11 work of installing new dog conductor in place of the bad life conductor in the line of cabin feeder coming out of kb power substation ( 3 ) 33 / work of replacing damaged balls in 11 kv power station rath pratham ( 4 ) of jal nigam feeder coming out from 35 / 11 kv power station sad. g.n. rbval conductor replacement work ( 5 ) 33 / 11 kv power station ramseshit nami breeders llb. e. coral replacement work. 1 supply & erection 2 11 m stp pole (provided by department) 3 pcc pole 8.5 m long (provided by department) 4 stone pad 300x300x75 mm 5 x arm ms angle 65x65x6 mm v type 6 cross arm holding clamp with bolt & nuts(providing by department) 7 11 kv pin insulator with pin (provided by department) 8 11 kv disc fitting (45 kn & t&c) provided by department 9 11 kv disc insulator (provided by department) 10 f bracket with bolt & nut 11 barbed wire 12 t off channel 13 top channel 125x65x2240 mm 14 clamp for channel 15 clamp for gaurding angle 16 11 kv f clamp 17 red oxide paint 18 alluminium paint 19 bolts nuts & washers 20 danger board with clamps 21 acsr dog conductor (provided by department) 22 stay wire gi (7/3.15) 7/10 swg 23 stay set 16x1800 24 11 kv stay insulator 25 11 kv stay clamp for pcc pole 8.5 m 26 earthing complete 27 gi pipe 6 dia 28 laying of 11 kv cable including cost of sand & bricks 29 11 kv 3 core 185 mm xlpe cable(provided by department) 30 11 kv cable jointing kit 185 sqmm (indoor & outdoor)(provided by department) 31 conducting binding wire 32 grouting of pole 33 concreating of stay ...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39791068 various electrical work of electric supply in the area of edsd iiird ( jalesar ) etah ( edd iind, etah ) under additional business plan ( 339 cr. ) on semi turnkey basis. 2 holding clamp 3 ms angle 75x75x682028 mm with clamp 4 ms droper channel 5 ms top channel 6 mst off channel wit clamp 7 nut & bolt with washer 8 stone pad 9 danger boardwith clamp 10 gaurding angle with clamp 11 barbed wire 12 earthing wire with clamp 13 lt shackle insulator 14 lt clamp 15 alliminum lug barrel off size ( ls ) 16 erection work : 17 safe carriage of line material from store center etah to pit site in distance range 0 to 60 km including loading & unloading at both ends. 18 safe carriage of 33 kvxlpe cabel 3x300 sqmm from store center etah to pit site in distance range 0 to 60 km including loading & unloading at both ends. 19 safe carriage of following vcb from store center etah to pit site in distance range 0 to 60 km including loading & unloading at both ends. 20 33 kv vcb 21 11 kv vcb 22 safe carriage of 8.5 mtr long pcc pole from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side 23 safe carriage of 11 mtr long st pole from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side 24 safe carriage of 100 kva tf from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side. 25 erection of 8.5 mtr long pcc pole as single support including fixing of ht / lt accessories etc and other work complete as per respo norms. 26 erection of 11 mtr long st pole as single support including fixing of ht / lt accessories etc and other work complete as per respo norms. 27 erection of 8.5 mtr long pcc pole as double pole / section pole including fixing of ht / lt accessories with tpmo etc. and other work complete as per respo norms. 28 dismantling and removal of existing acsr weasel / dog conductor / rabbit conductor from the various area, stacking and placement their coils and their in the safer place including cost of lobour t&p etc. required for proper completion of work. 29 laying sagging stringing, binding, jumpering & fixing of all accessories etc of following conductor on the newly / old erected pole as per respo manual and as per direction of supervising engineer. it includes the cost of labour, t & p, carrier etc required for proper completion of work. 30 ( a ) acsr weseal conductor 31 ( b ) acsr dog conductor 32 ( c ) rabbit conductor 33 ( d ) 33 kv xlpe cable 3x300 sqmm 34 ( e ) lt pvc cable al. 1x400 sqmm 35 ( f ) lt pvc cable al. 1x240 sqmm 36 ( g ) lt pvc cable 4x16 sqmm 37 re sagging of looseweseal / rabbit / dog conductor as per direction of supervising engineer. it includes the cost of labour, t & p carrier etc required for proper completion of work. 38 stone pad 39 erection and grouting of stays as per respo norms and as per direction of supervising engineer. grouting material i.e. cement, sand, brick ballast / stone ballast etc. shall be arranged by the contractor at his own cost. 40 earthing complete 41 11 kv vcb o / g ctr 200 / 100 / 5a 350 mva 42 33 kv cable jointing kit o / d 3x300 sq mm 43 33 kv cable jointing kit i / d 3x300 sq mm 44 making of 33 kv vcb double tf control panel nct 200 / 100 1amp with structure as per respo norms. 45 danger boardwith clamp 46 barbed wire 47 mounting of 100 kva tf on d / p including making of the connection etc. complete. 48 repairing / resagging / new guardingof ht line with gi wire 6 swg as per respo norms. 49 any other material / consumable required to complete the work shall be arrange by the contractor at his own cost. 50 carriage of acsr dog / rabbit / weseal conductor ( scrap ) from pit site to je store / store center etah in distance range 0 to 60 km. including loading & unloading and proper stacking....

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39789838 tender for essential and very important work due to summer season under additional business plan 2023 24 on semi turnkey basisin the area of edc i, mathura 1 8.5 mtr long pcc pole 2 11 mtr long st pole 3 13 mtr long st pole 4 11 / 0.4 kv 25 kva transformer 5 11 / 0.4 kv 10 kva transformer 6 acsr weasel conductor 7 arial bunch conductor 3x50 sqmm 8 arial bunch conductor 3x95 sqmm 9 11 kv xlpe cable 3x70 sqmm 10 distribution box with clamp 11 cross arm clamp 12 11 kv tpmo 13 11 kv cross arm with clamp 14 11 kv pin insulator with pin 15 11 kv disk insulator with fitting 16 11 kv f bracket with clamp 17 11 kv stay complete 18 11 kv fuse set 19 earthing rod 20 g.i. wire 8 swg 21 dp clamp 22 stone pad 23 m.s. top channel for 11 kv line 24 dropper channel for 11 kv line 25 m.s. angle t / f base 26 danger board with clamp 27 barbed wire 28 holding clamp 29 t channel with clamp 30 lt clamp 31 guarding angle with clamp 32 nut bolt with washer 33 transformer plinth for 250 kva t / f 34 concreating of pole as per respo norms 35 concreating of stay as per respo norms...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39788690 additional business plan work under ee eudd i and ii jhs 2 local / de centralised items all items will be supplied and errected by firm. 3 al lug 35 sq mm 4 al lug 120 sq mm 5 al lug 150 sqmm 6 al lug 240 sq mm 7 al. lug 400 sqmm 8 hs 11 kv cable jointing kit ( 3x120 ) sqmm 0 / d 9 hs 11 kv cable jointing kit ( 3x185 ) sqmm o / d 10 hs 33 kv cable jointing kit ( 3x300 ) sqmm o / d 11 bolt nut and washer all size 12 alluminium tape 13 pg clamps 16 sqmm 50 sqmm ( for line to line jumpering ) 14 supply of lt pvc cable ( armoured ) 4*16 sqmm 15 stone pad 16 alluminium binding wire 6 swg 17 pg clamp for acsr dog 18 m.s. angle iron 65*65*6 mm, 4300 mm long bracing with clamp 19 nut & bolts with washers all size 20 cu. l clamp 21 11 kv ct metering / dlms unit complete 22 barbed wire fencing with gate etc ( switchyard ) 23 11 kv danger board with clamps & bolts 24 barbed wire gi 25 aqua check lt energy meter test kit 26 aqua check 11kv energy meter test kit 27 primary current injection testing set 400a 28 primary current injection testing set 600a 29 ct polarty tester test kit ac / dc 30 testing board for power transformer 31 earth registance tester 32 megger ( 5000v 10000moh ) 33 clamp meter ( tong tester ) 34 t&p set complete 35 earthing of transformer ( chemical / pipe / plate etc ) complete for cable 36 11 kv lightning arrester 37 4 core lt mcb with box lt incoming protection panel with metering equipment ( type a 100 to 500 amp 4pole mcb with box / lt protection panel ) 38 33 kv lightning arrestor 39 33 kv vcb with single t / f control pannel and ct 200 / 100 / 1 a with structure 40 structure for above 41 structure for above 42 service contractor quote their errection rate only. 43 giving the genuine consumer service connection through installed lt distribution box including disconnection & reconnection 44 repairing of 9 / 11 m st / rsj pole by muffing and breaking cc / hard surface of rusted and tilted st pole and digging about 4 feet to prevent, grout and muffing with the help of stones etc in well made pits 45 number / dt code etc marking on pole by paint, yellow base will be prepared and number shall be written by black paint ( paint provided by contractor ) 46 plinth complete 47 laying of 11 kv cable including cost of sand and bricks 48 painting of s / s structure 49 extra r&m works on existing netwrok for strengthing 50 road restoration charges for pucca road 51 road restoration charges for kachha footpath side 52 dismentalling of old and used line material as per nature of work 53 back carriage of receive back material from concerne site to esc hansari or as per direction by inchareg 54 concreting of poles 55 painting of pole with red oxide / silver oxide paint of two coat ( paint provided by contraction ) 56 number marking on pole by paint, yellow base will be prepared and number shall be written by black paint ( paint provided by contractor ) , etc....

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39750546 tender for increasing capacity of substation bangarmau gramin ajgain miyaganj hasanganj pathakauk bihar mawai gangaghat airabhadiyar p.d. nagar and industrial area unnao at distt unnao under business plan 2023 24 1 safe loading, carriage and unloading of following store material with proper stacking from any esc of lucknow zone to jes dump store / store to work site: ( approx.30 km ) 2 33 kv line isolator 3 33 kv lightening arrester 4 33 kv vcb 800 amp., 750 mva 5 33 kv ct 200 / 100 / 1 amp. 6 33 kv ct 400 / 200 / 1 amp. 7 11 kv vcb o / g ctr 200 / 100 / 5 amp, 350 mva 8 11 kv vcb bus coupler 9 11 kv 3x300 sq mm xlpe 10 11 kv 3x120 sq mm xlpe 11 ms angles 75x75x6mm 12 acsr panther conductor 13 pcc pole 8.5mtr long 14 st pole 11 mt long sp 55 15 11 kv v type cross arm 65x65x6 mm 16 polymeric 11 kv disc insulator b&s. type 70 kn. 17 disc fittingsdog / racoon 70 kn. 18 polymeric 33kv pin insulator 19 ms channel 125x65mm3.2 mtr. long 20 ms channel 100x50 mm 21 ms channel 100x50x2028 mm ( dropper for fuse set ) 22 ms channel 100x50x2240mm top channel 23 11 kv polymeric disc insulator t & c 24 11 kv disc fitting t & c type 4500 kg. 25 11 kv composite polymeric pin insulator 26 ms earthing rod 20x2500 mm 27 ms angle 65x65x6mm 2028 mm 28 guarding angle 65x65x6mm ( 2500 / 1600 ) mm 29 complete stay set ( gi stay rod 16x1800 mm ) 30 stay wire 7 / 10 swg ( 5 kg. / stay ) 31 11 kv 3x300 sq mm xlpe cable outdoor jointing kit 32 11 kv 3x300 sq mm xlpe cable indoor jointing kit 33 11 kv 3x120 sq mm xlpe cable outdoor jointing kit 34 11 kv 3x120 sq mm xlpe cable indoor jointing kit 35 gi wire 8 swg for guarding 36 gi wire 6 swg for earthing 37 acsr weasel conductor 38 single core pvc cable 1x240 sq.mm. 39 dismantling & safe shifting of existing old & non working 05 mva t / f from plinth to suitable storage place after opening jumper and cable connections as per required. 40 extension and repairing of existing power transformer plinth of 05 mva t / f as per required. 41 lightening arrestor, p.i. & ct structure : fabrication of lightening arrestor, p.i. & ct structure 3.5 mtr. in height as per drg. digging of two no pits of size 1.075x0.9x0.3 mtr. providing stone pad at the bottom of the pit and grouting of two legs of the structure in cc ( cement coarse sand and stone grit of 20mm gauge ) of the ratio 1:4:8 in block of 1.075x0.3 mtr. including all civil material, t&p complete in all respect. the work includes dragging, shifting up to 40 mtr., raising and erecting the two legs with runner on proper alignment and level and plumb. both plinths of the structure shall be properly finished with smoothing of edges. 42 plinth of vcb : construction of plinth of size 2.0 mtrx1.5mtrx0.9mtr. suitable for erection of upper structure of 33kv vcb including grouting of anchor bolts in proper alignment and level. scope of work includes excavation of foundation base and concreting in cc 1:3:6 ( cement, find sand & stone grit ) 1st class brick work in cement mortor ratio 1:4:8. 43 connection of 33 / 11kv 10 mva t / f at both side of ( ht / lt ) with proper & suitable connectors, lugs. this works also include jointing of earthing strip with body and neutral by proper welding and bolting. ( all decentralised materials are to be provided by contractor ) . 44 earthing for power t / fby way of boring and lowering of 40mm dia, 2.9 mm thick gi pipe b class from ground upto the water level ( minimum 60 feet deep ) as per standard practice as per respo / rec drg with making of earth pit of 300x300 mm & 1 feet deep with cover. ( all materials to be provided by contractor ) . 45 neutral standfabrication and grouting ( 1:4:8 ) of ms angle 75x75x6mm in l shape & in proper size and alignment to provide support through gi earthing strips ( 50x6 ) mm size for power transformer neutral including supply & fixing of flexible copper bonds for neutral earthing as per respo drg. ( all decentralised materials to be provided by contractor ) . 46 cable standfabrication and erection of cable support made of two pieces of ms channel 100x50mm, 3.0 mtr. long joined to each other by means of 5 no. ms flat 50x6mm pieces of size 150mm long each by welding at equal intervals as per drawing and grouting in block of size 300x300x700mm ( 1:4:8 ) complete. this includes providing of required ms clamp made of ms flat holding the cable including nuts & bolts and fixing of xlpe cable. 47 installation of isolators: assembling and installation of line / bus isolator on the isolator structure adjusting of opening mechanis in proper alignment so as to ensure smooth operation of the same. in case of line isolator proper operation of earth links shall also be ensured. the work includes fabrication & proper connection with earthmat / earthing by g.i. earth strip 50x6mm proper fixing if required ( all decentralised materials to be provided by contractor ) . 48 installation of p.i. & lightening arrestors : assembling, installation & mounting of 3 no. ( 1set ) l.a. & post insulator on the l.a & p.i. structure / complete with making earth connections ( separate ) with gi strip 50x6mm. the work includes fabrication for fixing if required. ( all decentralised materials to be provided by contractor ) . 49 installation of ct: installation of 3 no. ( 1 set ) ct on the ct structure along with ct junction box. the work includes fabrication, proper fixing of c.t. with making earth connections ( earth mat / earthing ) with gi strip 50x6mm and control wiring connection, proper commissioning & testing. ( all decentralised materials to be provided by contractor ) . 50 installation of vcb: installation of 33kv vcb complete work with making earth connections ( earth mat / earthing ) with gi strip 50x6mmincluding control wiring, commissioning & testing ( all decentralised materials to be provided by contractor ) . 51 installation of switchgears in control room:shifting carefully & installation safely 11kv i / c, o / g & bus couplar switchgears from outside the switchgear room placing and fixing of switchgear on foundation providing g.i. bolt & nuts of proper size in proper position and alignment. this includes checking, complete work with mounting of p.t. on incoming s / g with proper testing, connetion of earthing & commissioning of switchgears. 52 fixing and making bus bar connections in between all switchgears after cleaning and tapping with h.t. tape, empire tape and pvc tape properly, providing and fixing of 6 mm thick bakelite separators and plugging of all opening & holes with plastic compound complete work as per required. 53 earthing of 11 kv, 33 kv switchgears & equipment: earthing of 11 kv, 33 kv switchgears equpiment by lowaring and boring of chemical earthing outside of switchyard and connecting through g.i. strip 50x6mm with indoor / outdoor equipments with making of earth pit of 300x300 mm & 1 feet deep with cover. ( all the material provided by the contractor ) 54 painting of all structures and equipments with good quality isi mark one coat of red oxide primer & two coats of aluminium paint. 55 laying & dressing of 11kv 3x300 sq.mm xlpe cable from 10mva t / f to 11kv incoming switchgear by excavation of trench in the ground of size 450mm wide, 900mm deep providing 150mm fine sand cushion belowthe cable. the cable shall be duly protected by bricks, sand & stone slab and refilling & ramming of the left out soil. spare cable shall be left and buried in the trench in the shape of rings at both ends. cable laying work includes unrolling, cutting, making ring and sealing both ends of the cable. ( all decentralised materials to be provided by contractor ) . 56 laying & dressing of 11kv 3x120 sq.mm xlpe cable from11kv o / g switchgear by excavation of trench in the ground of size 450mm wide, 900 / 1200 mm deep providing 150mm fine sand cushion below & abovethe cable. the cable shall be duly protected by bricks, sand & stone slab and refilling & ramming of the left out soil. spare cable shall be left and buried in the trench in the shape of rings at both ends. cable laying work includes unrolling, cutting, making ring and sealing both ends of the cable. ( all decentralised materials to be provided by contractor ) . 57 hoisting of 11kv cable with 100 mm dia 3 mtr. long gi pipe on the feeder cable before mounting the cable on the double pole, lifting, mounting and clamping of 11kv feeder cable boxes on the feeder double pole structure and making connection including supply of cable mounting clamps. the work includes the sealing of gi pipes, lower end of the pipe is to be buried into the earth by about one foot. ( all decentralised materials to be provided by contractor ) . 58 connection of 11kv xlpe cable for 11 kv switchgears & 33 / 11kv t / f of requried size. 59 making vertical / horizontal jumper connections using panther / dog conductor with existing busbar gantry through pg clamps and connecting all equipments with each other through connecting clamps. the work includes all the jumpers from busbar tot / f ( 1no. t / f bay & all equipments ) ( all fitting clamps, pg connector etc. to be provided by contractor ) . 60 supply and laying of following size copper control cable through underground / cable trench / trenching sgr interlinking through proper connections to t / f control panel / protection board / battery and battery charger / bunch joints, relay 33 / 11kv t / f junction box / 33kv vcb, cts etc. as per site conditions: 61 4x2.5 sq.mm 62 6x2.5 sq.mm 63 fixing of single corepvc cable, 1x240 / 400 / 630 sq.mm. & fixing between transformer incoming 3x300 sq.mm xlpe cable and transformer 11 kv / lv side bushing connector for reducing of tension at lv side bushing. 64 construction of 11 kv feeders : ( a ) excavation of foundation pit in mix soil / normal soil, soft & hard rock and its back filling and levelling etc. the size of the pit will be 800x900 mm and having a depth of 1 / 6 of the full length of the support. erection of supports by providing stone pad, fixing all clamps and other accessories such as no. plate, danger board, barbed wire ( 2kg. ) , painting ( one coat red oxide primer & two coats of red& aluminium paint at required height ) . as per relevant respo / res. drawing . this includes any fabrication, if required. ( b ) grouting of above supports with cement, concrete ( cc will be of cement coarse sand & stone grit ) grouting will be done with the help of wooden / steel formers in a block of size 450 mm x 450 mm x 1 / 6 of the full length of the support in the cc 1:4:8 ratio as per respo / res. drawing including back filling and proper ramming. ( c ) making plinth of stp 300 mm, dia & 300 mm above ground level in cc of 1:4:8 & plastering of the same with 12 mm thick plaster of cement & sand in 1:4 ratio. ( d ) earthing of supports with earth electrode 2.5 mtr. length including excavation of pit and driving m.s. rod upto proper depth and connecting the earth electrode with the help of 6 / 8 swg g.i. wire and earthing lugs. respo / res. drawing. 65 double pole structure for outgoing feeder on 8.5 mtr pcc pole with complete accessories. 66 single support on 11mtr. stp : 67 single support on 8.5 mtr pcc pole : 68 ( a ) grouting of stay rods 1800x20 mm including all works of excavation grouting by, cement concrete in size 0.60x0.60x0.3 mtr. with ratio 1:4:8 as per relevant drawing including back filling of earth and proper ramming. ( b ) fixing, making of loop insulator, tightening & nuzzling of stay with the poles and required tension as per respo / res. drawing. 69 laying, spreading, lifting, stinging, jointing and final sagging of acsr dog / weasel conductor in accordance with profiles and sag chart including binding, jumpering and fixing of all accessories in 3 nos. conductor in parallel with pg clamp binding wire etc requested for job. 70 guarding between two poles like single / double / tri. / four poles etc. to guardlt / 11 kv / telephone lines, road / river crossing etc. with g.i. wire 6 swg and g.i. wire 8 swg including fixing of guarding channel of requested sitewith clamps and nuts and bolts as per respo / res. drawing 71 supply and installation of 24 volt battery and it charger with connections to existingcontrol circuit complete in all respects. 72 looping of branches of trees along the route of line and disposal of the same after obtaining permission of competant authority....

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39749464 tender for increasing capacity offollowing 33 / 11 kv sub stationsranapur from 2x5 to 1x5+1x10 mva t / f, khero 2x10+1x5 to 3x10 mva, uchahar ( tehsil ) 2x5 mva to 1x5+1x10 mva, gadaganj 1x5+1x10 mva to 2x10 mva & deeh 3x5 mva to 2x5+1x10 mva distt raebareli; 1 safe loading, carriage and unloading of following store material with proper stacking from any esc of lucknow zone to jes dump store / store to work site: ( approx.0 30 km ) 2 33 kv bus isolator 3 33 kv post insulator 4 33 kv lightening arrester 5 33 kv vcb 800 amp., 750 mva 6 33 kv ct 200 / 100 / 1 amp. 7 33 kv double t / f control pannel 8 11 kv vcb o / g ctr 200 / 100 / 5 amp, 350 mva 9 11 kv 3x300 sq mm xlpe 10 11 kv 3x120 sq mm xlpe 11 ms angles 75x75x6mm 12 acsr panther conductor 13 pcc pole 8.5mtr long 14 st pole 11 mt long sp 55 15 11 kv v type cross arm 65x65x6 mm 16 polymeric 11 kv disc insulator b&s. type 70 kn. 17 disc fittingsdog / racoon 70 kn. 18 polymeric 33kv pin insulator 19 ms channel 125x65mm3.2 mtr. long 20 ms channel 100x50 mm 21 ms channel 100x50x2028 mm ( dropper for fuse set ) 22 ms channel 100x50x2240mm top channel 23 11 kv polymeric disc insulator t & c 24 11 kv disc fitting t & c type 4500 kg. 25 11 kv composite polymeric pin insulator 26 ms earthing rod 20x2500 mm 27 ms angle 65x65x6mm 2028 mm 28 guarding angle 65x65x6mm ( 2500 / 1600 ) mm 29 complete stay set ( gi stay rod 16x1800 mm ) 30 stay wire 7 / 10 swg ( 5 kg. / stay ) 31 11 kv 3x300 sq mm xlpe cable outdoor jointing kit 32 11 kv 3x300 sq mm xlpe cable indoor jointing kit 33 11 kv 3x120 sq mm xlpe cable outdoor jointing kit 34 11 kv 3x120 sq mm xlpe cable indoor jointing kit 35 gi wire 8 swg for guarding 36 gi wire 6 swg for earthing 37 acsr weasel conductor 38 single core pvc cable 1x240 sq.mm. 39 dismantling & safe shifting of existing old & non working 05 mva t / f from plinth to suitable storage place after opening jumper and cable connections as per required. 40 extension and repairing of existing power transformer plinth of 05 mva t / f as per required. 41 lightening arrestor, p.i. & ct structure : fabrication of lightening arrestor, p.i. & ct structure 3.5 mtr. in height as per drg. digging of two no pits of size 1.075x0.9x0.3 mtr. providing stone pad at the bottom of the pit and grouting of two legs of the structure in cc ( cement coarse sand and stone grit of 20mm gauge ) of the ratio 1:4:8 in block of 1.075x0.3 mtr. including all civil material, t&p complete in all respect. the work includes dragging, shifting up to 40 mtr., raising and erecting the two legs with runner on proper alignment and level and plumb. both plinths of the structure shall be properly finished with smoothing of edges. 42 plinth of vcb : construction of plinth of size 2.0 mtrx1.5mtrx0.9mtr. suitable for erection of upper structure of 33kv vcb including grouting of anchor bolts in proper alignment and level. scope of work includes excavation of foundation base and concreting in cc 1:3:6 ( cement, find sand & stone grit ) 1st class brick work in cement mortor ratio 1:4:8. 43 33 / 11kv 10 mva t / f connection of 33 / 11kv 10 mva t / f at both side of ( ht / lt ) with proper & suitable connectors, lugs. this works also include jointing of earthing strip with body and neutral by proper welding and bolting. ( all decentralised materials are to be provided by contractor ) . 44 earthing for power t / fby way of boring and lowering of 40mm dia, 2.9 mm thick gi pipe b class from ground upto the water level ( minimum 60 feet deep ) as per standard practice as per respo / rec drg with making of earth pit of 300x300 mm & 1 feet deep with cover. ( all materials to be provided by contractor ) . 45 neutral standfabrication and grouting ( 1:4:8 ) of ms angle 75x75x6mm in l shape & in proper size and alignment to provide support through gi earthing strips ( 50x6 ) mm size for power transformer neutral including supply & fixing of flexible copper bonds for neutral earthing as per respo drg. ( all decentralised materials to be provided by contractor ) . 46 cable standfabrication and erection of cable support made of two pieces of ms channel 100x50mm, 3.0 mtr. long joined to each other by means of 5 no. ms flat 50x6mm pieces of size 150mm long each by welding at equal intervals as per drawing and grouting in block of size 300x300x700mm ( 1:4:8 ) complete. this includes providing of required ms clamp made of ms flat holding the cable including nuts & bolts and fixing of xlpe cable. 47 installation of isolators: assembling and installation of line / bus isolator on the isolator structure adjusting of opening mechanis in proper alignment so as to ensure smooth operation of the same. in case of line isolator proper operation of earth links shall also be ensured. the work includes fabrication & proper connection with earthmat / earthing by g.i. earth strip 50x6mm proper fixing if required ( all decentralised materials to be provided by contractor ) . 48 installation of p.i. & lightening arrestors : assembling, installation & mounting of 3 no. ( 1set ) l.a. & post insulator on the l.a & p.i. structure / complete with making earth connections ( separate ) with gi strip 50x6mm. the work includes fabrication for fixing if required. ( all decentralised materials to be provided by contractor ) . 49 installation of ct: installation of 3 no. ( 1 set ) ct on the ct structure along with ct junction box. the work includes fabrication, proper fixing of c.t. with making earth connections ( earth mat / earthing ) with gi strip 50x6mm and control wiring connection, proper commissioning & testing. ( all decentralised materials to be provided by contractor ) . 50 installation of vcb: installation of 33kv vcb complete work with making earth connections ( earth mat / earthing ) with gi strip 50x6mmincluding control wiring, commissioning & testing ( all decentralised materials to be provided by contractor ) . 51 installation of switchgears in control room:shifting carefully & installation safely 11kv i / c & o / g switchgears from outside the switchgear room placing and fixing of switchgear on foundation providing g.i. bolt & nuts of proper size in proper position and alignment. this includes checking, complete work with mounting of p.t. on incoming s / g with proper testing, connetion of earthing & commissioning of switchgears. 52 fixing and making bus bar connections in between all switchgears after cleaning and tapping with h.t. tape, empire tape and pvc tape properly, providing and fixing of 6 mm thick bakelite separators and plugging of all opening & holes with plastic compound complete work as per required. 53 shifting carefully and installation of 33kv single / double transformer control panel in control room including fixing, bolting & grouting of above as per required and testing, commisioning complete work as per required. 54 earthing of 11 kv, 33 kv switchgears & equipment: earthing of 11 kv, 33 kv switchgears equpiment by lowaring and boring of chemical earthing outside of switchyard and connecting through g.i. strip 50x6mm with indoor / outdoor equipments with making of earth pit of 300x300 mm & 1 feet deep with cover. ( all the material provided by the contractor ) 55 painting of all structures and equipments with good quality isi mark one coat of red oxide primer & two coats of aluminium paint. 56 ht cable laying :laying & dressing of 11kv 3x300 sq.mm xlpe cable from 10mva t / f to 11kv incoming switchgear by excavation of trench in the ground of size 450mm wide, 900mm deep providing 150mm fine sand cushion belowthe cable. the cable shall be duly protected by bricks, sand & stone slab and refilling & ramming of the left out soil. spare cable shall be left and buried in the trench in the shape of rings at both ends. cable laying work includes unrolling, cutting, making ring and sealing both ends of the cable. ( all decentralised materials to be provided by contractor ) . 57 laying & dressing of 11kv 3x120 sq.mm xlpe cable from11kv o / g switchgear by excavation of trench in the ground of size 450mm wide, 900 / 1200 mm deep providing 150mm fine sand cushion below & abovethe cable. the cable shall be duly protected by bricks, sand & stone slab and refilling & ramming of the left out soil. spare cable shall be left and buried in the trench in the shape of rings at both ends. cable laying work includes unrolling, cutting, making ring and sealing both ends of the cable. ( all decentralised materials to be provided by contractor ) . 58 hoisting of 11kv cable with 100 mm dia 3 mtr. long gi pipe on the feeder cable before mounting the cable on the double pole, lifting, mounting and clamping of 11kv feeder cable boxes on the feeder double pole structure and making connection including supply of cable mounting clamps. the work includes the sealing of gi pipes, lower end of the pipe is to be buried into the earth by about one foot. ( all decentralised materials to be provided by contractor ) . 59 connection of 11kv xlpe cable for 11 kv switchgears & 33 / 11kv t / f of requried size. 60 making vertical / horizontal jumper connections using panther / dog conductor with existing busbar gantry through pg clamps and connecting all equipments with each other through connecting clamps. the work includes all the jumpers from busbar tot / f ( 1no. t / f bay & all equipments ) ( all fitting clamps, pg connector etc. to be provided by contractor ) . 61 supply and laying of following size copper control cable through underground / cable trench / trenching sgr interlinking through proper connections to t / f control panel / protection board / battery and battery charger / bunch joints, relay 33 / 11kv t / f junction box / 33kv vcb, cts etc. as per site conditions: 62 4x2.5 sq.mm 63 6x2.5 sq.mm 64 fixing of single corepvc cable, 1x240 / 400 / 630 sq.mm. & fixing between transformer incoming 3x300 sq.mm xlpe cable and transformer 11 kv / lv side bushing connector for reducing of tension at lv side bushing. 65 construction of 11 kv feeders : ( a ) excavation of foundation pit in mix soil / normal soil, soft & hard rock and its back filling and levelling etc. the size of the pit will be 800x900 mm and having a depth of 1 / 6 of the full length of the support. erection of supports by providing stone pad, fixing all clamps and other accessories such as no. plate, danger board, barbed wire ( 2kg. ) , painting ( one coat red oxide primer & two coats of red& aluminium paint at required height ) . as per relevant respo / res. drawing . this includes any fabrication, if required. ( b ) grouting of above supports with cement, concrete ( cc will be of cement coarse sand & stone grit ) grouting will be done with the help of wooden / steel formers in a block of size 450 mm x 450 mm x 1 / 6 of the full length of the support in the cc 1:4:8 ratio as per respo / res. drawing including back filling and proper ramming. ( c ) making plinth of stp 300 mm, dia & 300 mm above ground level in cc of 1:4:8 & plastering of the same with 12 mm thick plaster of cement & sand in 1:4 ratio. ( d ) earthing of supports with earth electrode 2.5 mtr. length including excavation of pit and driving m.s. rod upto proper depth and connecting the earth electrode with the help of 6 / 8 swg g.i. wire and earthing lugs. respo / res. drawing. 66 double pole structure for outgoing feeder on 8.5 mtr pcc pole with complete accessories. 67 single support on 11mtr. stp : 68 single support on 8.5 mtr pcc pole : 69 ( a ) grouting of stay rods 1800x20 mm including all works of excavation grouting by, cement concrete in size 0.60x0.60x0.3 mtr. with ratio 1:4:8 as per relevant drawing including back filling of earth and proper ramming. ( b ) fixing, making of loop insulator, tightening & nuzzling of stay with the poles and required tension as per respo / res. drawing. 70 laying, spreading, lifting, stinging, jointing and final sagging of acsr dog / weasel conductor in accordance with profiles and sag chart including binding, jumpering and fixing of all accessories in 3 nos. conductor in parallel with pg clamp binding wire etc requested for job. 71 guarding between two poles like single / double / tri. / four poles etc. to guardlt / 11 kv / telephone lines, road / river crossing etc. with g.i. wire 6 swg and g.i. wire 8 swg including fixing of guarding channel of requested sitewith clamps and nuts and bolts as per respo / res. drawing 72 looping of branches of trees along the route of line and disposal of the same after obtaining permission of competant authority. 73 gst will be paid extra as applicable....

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39748855 various electrical work for strengthening of electric supply in the area of eusd iindetah ( eudd, etah ) under additional business plan on semi turnkey basis. 2 danger board with clamp 3 stone pad 4 tee off channal 125x65x1300 mm 5 tee chanel clamp 6 top channal 7 top channal clamp 8 nut bolt with washer 9 holding clamp 10 dropper channal 11 dropper channal clamp 12 11 kv fuse set 13 dead end clamp 14 copper l piece 62x225x12 mm 15 lt incoming pannel with metering qubical 16 suspension clamp 17 i hook 18 allumunium lug 400 sqmm 19 lt pin clamp for pcc 20 lt pin clamp for stp 21 meger ( reputed make ) 22 earth tester ( reputed make ) 23 multimeter cum tong tester ( reputed make ) 24 pearcing connector 25 tripping coil for vcb 26 lt pvc 3.5x400 sqmm 27 erection work : 28 safe carriage of following material from electricty store center etah to pit site of work through the kacha and pakka road includingloading and unloading at the respective ends including the cost of arrangement of labour, t&p, etc. which required for proper completion of work. ( distance 00 10 kms. ) 29 ( a ) 8.5 mtr long pcc poles. 30 ( b ) 11 mtr long st poles. 31 ( c. ) 13 mtr long st poles. 32 ( d ) 11 kv x arms, weasal conductor, g.i wire, dog conductor, disc insulators, pin insulators, clamps abc bunch and otherrequired line material, if any. 33 ( e. ) 33 kv xlpe cable ( 3*185 sqmm ) 34 ( f ) 33 kv xlpe cable ( 3*300 sqmm ) 35 ( g ) 11 kv xlpe cable ( 3*95 sqmm ) 36 safe carriage of following from electricty store center etah to pit site of work through the kacha and pakka roadloading and unloading at the respective ends including the cost of arrangement of labour, t&p, etc. which required for proper completion of work. ( distance 00 10 kms. ) 37 ( a ) 63 / 100 kva t / f 38 ( b ) 250 / 400 kva 39 erection of following poles with grouting including cutting of kharanja / mettalic road / concrete portion while digging pit & complete h.t. / l.t. fittings as per respo manual and as per direction of engineer incharge including the cost of labour, t&p and carrier etc. required for proper completion of work. 40 ( a ) 8.5 mtr long pcc pole 41 ( b ) 11 mtr long st pole 42 ( c ) 13 mtr long st pole 43 erection of d / p or section pole including drilling, cutting of material etc. andfixing of all accessories etc. complete. 44 ( a ) 8.5 mtr long pcc pole 45 ( b ) 11 mtr long st pole 46 shifting of power transformer having capacity 5 mva from yard to the safer place with help of crain after disconnecting neutral / body earthing properly as per uppcl / dvvnl norms. 47 ereection and installation of 33 / 11 kv, power transformer in a leveled position on the plinth. the work include shifting of transformer to the site of the installation within the sub station premises, assembling, fixing and fitting of all accessories and filling of transformer oil to the desired level and ensuring that there is no leakage. 48 fixing / erection oflt incoming pannel with metering equiptment, grouting as per respoo manual all cost of labor, material and t&p which required for completion of work 49 erection and grouting of stays as per respo norms and as per direction of supervising engineer. grouting material i.e. cement, sand, brick ballast / stone ballast etc. shall be arranged by the contractor at his own cost. 50 fixing of earthing rod as per respo norms and as per direction of supervising engineer. 51 dismantling and removal of existing acsr weasel / dog / ab cable from the various area, stacking and placement their coils and their in the safer place including cost of lobour t&p etc. required for proper completion of work. 52 laying, sagging and stringing and jumpering / binding etc. ofnew &old acsr weasal conductor / giin 11 kv / lt lines as per respo manual and as per direction of supervising engineer. 53 ( a ) acsr weasel conductor 54 ( b ) acsr dog conductor 55 ( c. ) 33 kv xlpe cable 3*185 sqmm 56 ( d ) ab cable 50 / 95 / 120 sqmm 57 ( e. ) lt pvc cable 3.5x150 / 3.5x400 sqmm 58 ( f ) lt cable 3x120 sqmm 59 installation of 250 / 400 kva t / f on newly / old constructed plinth in proper alignment direction & making ht / lt connection all cost of labour and t&p which required for completion of work 60 11 kv pt 61 11 kv tpmo with polymer insulator 62 11 kv fuse set 63 danger board barbed wire including jumper 64 33 kv cable joiting kit i / d 3x185 sqmm 65 33 kv cable joiting kit o / d and 3x185 sqmm 66 11 kv cable joiting kit i / d 3x185 sqmm 67 11 kv cable joiting kit o / d and 3x185 sqmm 68 cable joiting kit o / d and 3x300 sqmm 69 11 kv ct o / g 400 / 5a 70 11 kv ct i / c 600 / 300 / 5a 71 3 phase distribution box 72 meter box 73 pvc armoud cable 2x6 sqmm 74 single core pvc cable 1x1000 sqmm 75 single core pvc cable 1x630 sqmm 76 single core pvc cable 1x400 sqmm 77 single core pvc cable 1x240 sqmm 78 lt pvc cable al 3.5x150 sqmm 79 lt protection of dt ( mccb ) 80 vaccume intruptor ( off make ) 81 tripping coil for vcb ( stelmec ) 82 pipe earthing of 250 / 400 kva medium power transformers 83 net fencing shall be 1150*1200 mm made of 35*35 mm ms angle covered by expended netal 14 swg up to full height 1200 mm duly steftened by ms flat by an 8 swg dia bolt & nut 84 gi wire 6 swg 85 red oxide paint 86 alluminum paint 87 any other material / consumable required to complete the work shall be arrange by the contractor at his own cost. 88 carriage of following old material from pit site to je store / store center etah in distance range 0 to 10 km. including loading & unloading and proper stacking. 89 1 100 kva tf ( old ) 90 2 scrap ( all line material ) ...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39748840 electric work under the full deposit scheme, the work of issuing combination as per application on nivesh mitra / jhatpat portal and creation of line etc. 2 carriage of fallowings from esc. bsr to pit site on kachcha pacaa road including loading and unloading chagres at both ends, rcquricd for proper completion of work, distance about to 60 kms. 3 s.t pole 13 mtr. long 4 s.t pole 11 mtr. long 5 pcc pole 8.5 mtr long. 6 carriage of all line material from store center bsr to j.e store sub station as acsr weasel conductor, abc conductor gi wire, earth wire. m.s. chanel, angle, stay & earthig rods, barbed wire. disc insulator etc. 7 erection ofsingle pole support including complete 1 it fittings as per respo manual and as per direction of engineer in charge including the cost of labour, t&p and carrier etc. required for proper completion of work. 8 erection of double pole / scation pole support including complete 1 it fittings as per respo manual and as per direction of engineer in charge including the cost of labour, t&p and carrier etc. required for proper completion of work. 9 grouting of single support shall be grouted with cement, sand and birck ballast / stone ballast in ratio 1:4:8 =30x3030 cms. including the cost of cement, sand, birck ballast / stone ballast, etc. as per actual size requirement, as per respo manual and as per direction of engineer in charge including the cost of labour, t&p and carrier etc. required for proper completion of work. 10 grouting of double pole support shall be grouted with cement, sand and birck ballast / stone ballast in ratio 1:4:8 =30x3030 cms. including the cost of cement, sand, birck ballast / stone ballast, etc. as per actual size requirement, as per respo manual and as per direction of engineer in charge including the cost of labour, t&p and carrier etc. required for proper completion of work. 11 carriage of all line material from j.e store sub station to pit site acsr weasel conductor, abc conductor gi wire, earth wire. m.s. chanel, angle, stay & earthig rods, barbed wire. disc insulator etc. 12 cutting / drilling / welding of ms angle iron for making guarding angle size 65x65x6 / 50x50x6 mm including the work of fixing the bracket on pcc / st pole for construction of the line. 13 carriage of 11 kv ct / pt metering polemounted unit varius ratio 14 carriage and installation of 11 kv pilferresistant metering cubicle with out cable termination kit 15 mounting of 11 kv ct / pt unit varius ratio 16 making / filling of 11 kv cable jointing kit varius sizexlpe cable 17 loading / unloading & carriage of t / ffrom esc. bsr to pit site on kachcha pacaa road including loading and unloading chagres at both ends, rcquricd for proper completion of work, distance about to 60 kms. 18 25 kva t / f 19 63 kva t / f 20 fixing of 11 kv stay rod with stay wire in proper way with nozelling 21 grouting of 11 kv stay rods 22 guarding of 11 k v line at road crossing by laying 3 nos. gl wire of size 6 / 10 swg parallel and fixing of lacings ( tilli ) at a distance at 1.5 mlrs as per direction of supervising engineer / respo mannual it. includes the cost of labour, t&p carrier etc. required lor proper completing of work 23 laying, sagging. stringing and binding and jumpering of 11 kv xlpe cable 3*70 square mm & outher size newly erected pole as per respo manual and as per direction of supervising engineer. it includes the cost of labour, t&p, carrier etc. requried for proper completion of work. 24 laying, sagging. stringing and binding and jumpering of acsr weisal , rabbit, dog newly erected pole as per respo manual and as per direction of supervising engineer. it includes the cost of labour, t&p, carrier etc. requried for proper completion of work. 25 acsr weisal conductor 26 acsr rabbit / dog conductor 27 abc cable 3*50 square mm 28 abc cable 3*95 square mm 29 abc cable 3*120 square mm 30 fixing of earthing rod 31 fixing of pin insulator 32 fixing of side bracket 33 fixing disc insulator 34 fixing ofv type x rm / toff channel 35 fixing ofdistrubution box. 36 fixing oftop / drop channel 37 fixing of sub station angle. 38 mounting & installation of t / f from d / p 39 25 kva t / f 40 63 kva t / f 41 the folloing material is required to be supplied by the contractor. 42 holding clamp. 43 11 kv cable jointing kit 3*70 square mm xlpe cable 44 double pole clamp 45 side bracket 46 f clamp 47 e clamp 48 lt clamp 49 pg clamp 50 i bolt with nut & bolt. 51 j hook 52 earth clamp 53 stay clamp 54 dead & clamps 55 stay insulator for 11 kv 56 suspension clamps 57 piercing connector. 58 lt insulator 59 bolt & nut off size....

Purvanchal Vidyut Vitaran Nigam Limited - Uttar Pradesh

39719167 work of electric pole utility shifting from the road for widening and strengthening of various roads in the deposit scheme year 2023 24 under executive engineer electricity distribution division siddharthnagar. 2 eye hook clamp 3 stay clamp 4 lt clamp 5 distribution box clamp 6 concreting of stay 7 concreting of pole 8 nutes and bolts of various size 9 11 kv x arm holding clamp 10 stay clamp with nut bolt 11 clamp with nut bolts 12 t off channel clamp 13 gurding angle clamp 14 top channel clamp 15 dropper angle clamps with nut bolts 16 lt eye hook 17 stay wire ( 3.15 mm ) 7 / 10swg ( gss wire ) 18 gi wire 5 mm 65 swg 19 ms earthing rod 20 stay set 16x1800 mm 21 11 kv v type x arm 22 stone pad 23 f bracket 24 11 kv pin insulator 25 11 pin with nut 26 danger board 27 barbed wire 28 top channel 29 11 kv disc fitting 30 gaurding angle 31 gi wire 4 mm 85 swg 32 t off channel 33 sub station base angle 34 dropper angle / channel 35 number plate 36 cross bracing m.s. angle 37 pg clamp 38 work portion work portion ( excluding gst ) 58 lt abc cable ( 1x16+1x25 ) 59 lt abc cable ( 3x50+1x35+1x16 ) 60 lt abc cable ( 3x95+1x70+1x16 ) 61 lt abc cable ( 3x120+1x95+1x16 ) ...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39717397 work of 33 kv, 11 kv line construction / strengthening , increasing capacity of power t / fs, feeder bifrecation, replacement / repairing of damaged vcbs and other associated works under system augmentation / strengthening work head on semi turn key basis under edd, kheragarh, agra. battery set 24 volt standard make 3 pg clamp 4 f bracket for fixing tap insulator nut & bolt 5 stone pad 6 number plate 7 barbed wire 8 danger board with clamp 9 part b (work/ erection)carriage of st pole 11 mtr long. from store center agra to work of site through kacha and pakka road including the work of its loading and unloading at the respective ends including the cost of arrangement of labour, t&p, carrier etc. required for proper completion of work.(distance 00 70kms.) 10 carriage of 11 kv i/c & o/g vcbs of various sizes from store center agra to work of site through kacha and pakka road including the work of its loading and unloading at the respective ends including the cost of arrangement of labour, t&p, carrier etc. required for proper completion of work.(distance 00 70kms.) 11 carriage of pcc pole 8.5 mtr. long. from store center agra to work of site through kacha and pakka road including the work of its loading and unloading at the respective ends including the cost of arrangement of labour, t&p, carrier etc. required for proper completion of work.(distance 00 70kms.) 12 carriage of 250 kva t/f from store center agra to work of site through kacha and pakka road including the work of its loading and unloading at the respective ends including the cost of arrangement of labour, t&p, carrier etc. required for proper completion of work.(distance 00 70kms.) 13 carriage of line material from store center agra to work of site through the kacha and pakka road including the work of its loading and unloading at the respective ends including the cost of arrangement of labour, t&p, carrier etc. required for proper completion of work.(distance 00 70kms.)line material viz. aerial bunch conductor/weasal conductor/dog/ rabbit, g.i. earth wire, cross arm, angle, channel, insulators,clamps, dist. box and other line material, if required in estimate/package. 14 erection and grouting in 1:2:4 ratio (cement, sand and bricks balast) on single pole 11 mtr. long st poles including fixing ofall accessories for 33 kv line as per respo norms.labour, t &p and carrier, grouting material etc. required for proper completion of work shall be done by the contractor at his own cost. 15 erection and grouting in 1:2:4 ratio (cement, sand and bricks balast) single pole on 8.5 mtr. longpcc poles including fixing ofall accessories, barbed wire for 11 kv/lt line as per respo norms labour, t &p and carrier, grouting material etc. required for proper completion of work shall be done by the contractor at his own cost. 16 erection and grouting in 1:2:4 ratio (cement, sand and bricks balast) double pole on 8.5 mtr. longpcc poles including fixing ofall accessories, barbed wire for 11 kv/lt line as per respo norms labour, t &p and carrier, grouting material etc. required for proper completion of work shall be done by the contractor at his own cost. 17 laying sagging stringing and binding and jumperingofacsr weasel conductor at 11 kv/lt lineas per respo norms it includes the cost of labour, t & p carrier etc required for proper completion of work. 18 laying sagging stringing and binding and jumperingofacsrdog conductor at 11 kv/lt lineas per respo norms it includes the cost of labour, t & p carrier etc required for proper completion of work. 19 bore earthing of 5 mva & 10 mva power t/f by digging machine depth of 250 ft. below as per respo norms. 20 erection and grouting stay of ratio 1:2:4 (cement, sand and bricks balast) as per respo norms including the costof arrangement of labour, t&p, carrier etc. required for proper completion of work. grouting material i.e. cement, sand, brick ballast/stone ballast etc. shall be arranged by the contractor at his own cost. 21 fixing of earthing rod as per respo norms including the cost of arrangement of labour, t&p, carrier etc. required for proper completion of work. 22 installation of 11 kv i/c & o/g vcb of various size in proper alignment and direction and jointing of earthing strips with help of gas welding and making cable connection including shifting dragging with all other associated works. 23 fixing of number plates on poles as per respo norms. 24 fixing ofaluminium p.g. clamps as per respo norms 25 fixing of danger boards with clamps (shock proof, rust proofs) on poles as per respo norms. 26 for the work construction of plinth, fencing of 250 kva t/f including the earthing (body/neturtal seperately) for above 250 kva t/f as per respo manual.(all material provided by the contractor at his own cost) 27 mounting of 250 kva t/f on plinth & making ht/lt connection. 28 installation & energization of battery set & charger of standard make and as per respo norms 29 removal & carriage of old / damaged 11 kv incoming/outgoing vcb from 33/11 kv s/s to 132 kv taj store agra including loading & unloading at respective ends. 30 removal & carriage of 100 kva t/f from existing double pole after opening ht/lt connections and their carriage to 132 kv taj store agra including laodiing and unloading at both end. ...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39717368 under the additional business plan 2023 24 ( 339 crore ) , for construction / strengthening / capacity increase / transformers of 33 kv / 11 kv line from a category experienced contractors on semi turnkey basis under the power distribution division firozabad and tundla works related to installation / worn wire / replacement of damaged cable / substation construction etc 1 33 kv jointing kit 3x300 sq.mm. 2 11 kv v type cross arm 3 11 kv v type cross arm holding clamp 4 do fuse set 11 kv 5 11 kv jointing kit 3x300 sq.mm. 6 11 kv jointing kit 3x185 sq.mm. i/d 7 11 kv jointing kit 3x185 sq.mm. o/d 8 11 kv straight through 3x185 sq.mm. 9 earthing complete 10 polymeric 11 kv pin insulator 11 dropper channel (100x50x2028 mm) 12 stone pad 13 holding clamp for top channel. tpmo & fuse set etc with bolts and nuts 14 base angle (75x75x6x2028 mm) with clamp & bolts and nuts 15 top channel (125x65x2240 mm) 16 stay set complete 17 concreting of pole 18 t off channel (125x65x1300 mm) 19 11 kv fuse set 20 gaurding angle with clamp 21 gi wire for gaurding 6/8 swg 22 chemical earthing complete 23 danger board with clamp 24 barbed wire gi 25 f bracket with n & b 26 supporting clamp for t/f with fixing clamp n & b 27 brassing 28 alluminium tap 29 road restoration charge 30 g.i. pipe 6 dia with laying charge 1475+725 31 cable laying charge along with digging 32 control cable 4*2.5 sq mm 33 control cable 2*2.5 sq mm 34 33kv pinwith nut 35 pg clamp dor jumpring 36 33kv fuse set 37 earth wire clamp with bolts & nuts 38 danger board with clamps 39 bolts nuts & washers 40 aluminium paints 41 red oxide paints 42 aluminium binding wire 6 swg 43 earthing of pole by ms earthing rod of 20x2500mm and 6 swg earthing wire etc. 44 ms angle iron 65x65x6mm, 4300mm long bracing with clamp 45 25 feet folding ledder 46 batterycharger 24 volt 47 batteryset 24 volt 48 tail less unit 49 received back material from site 50 11/0.4 kv 25 kva transformer 51 11/0.4 kv 63 kva transformer 52 acsr gi wire scrap 53 acsr weasel conductor (scrap) 54 5mva t/f 55 old used 11 kv xlpe cable 3x185 sqmm ( not damage ) 56 reccon/dog condutor 57 stp 11 mtr per pole 180 kg 58 33 kv xlpe cable 3x300 sqmm 59 11 kv xlpe cable 3x300 sqmm 60 11 kv xlpe cable 3x185 sqmm ...