Department of Higher Education - Uttar Pradesh
37667638 bids are invited for 1 student desk three seater material of desk top, seat & back: 18mm thick prelam particle board with all edges must be sealed with 2 mm pvc edge banding tape: edge banding must be trimmed on all edges & corners top size 1500w x 380d x 18mm , seat size 1550w x 300d x 18mm back size 1550w x 150h x 18mm , height of desk top in mm 760 mm type of desking desking configuration integrated desk cum seatings with shelf / storage under desk three seater material of support structure desk side frame structure made up of crca press formed section size 150mm x 25mm x 1mm thick welded to 25mm x 50mm x 1.2mm thick tube of 860mm length desk side frame structure made up of crca press formed section size 150mm x 25mm x 1mm thick welded to 25.4mm diameter x 1.2mm thickness welded to ms pipe. all 8 numbers of horizontol support shall be made up ms tube having dimension of 25mm x 25mm x 1.2mm thick understructure made up of rectangular ms tube of 50mm x 25mm x 1.2mm thick shall be closed with ppcp cap at both the ends pipe diameter 25.4mm x 1.2mm thick shall be closed with ppcp cap at back side & front upper modesty panel upper modesty panel shall be made of 0.8 mm thick crca sheet. the dimensions for upper modesty panel shall be 1000w x 25d x 130h. additional lower modesty panel lower modesty panel shall be made of 0.8 mm thick crca sheet. 240 2 executive table providing and placing executive table with side unit & back unit. the buildup of the main table is free standing structure strength up with the help of minifix dowels and pins. the complete table made of high quality prelaminated particle board with approved laminate and finish as per approved shade. the table top would be 1800mm ( ±10 ) long made with 25 mm prelaminated particle board and 900mm ( ±10 ) broad with two side gable ends with height of 750mm ( ±10 ) and width of 900mm ( ±10 ) made up with 18 mm prelaminated particle board. the 18 mm thick modesty of the table is giving more strength and look to the table. all the sharp edges of the table top and gable ends are lipped with 2mm thick edge binding tapes for the smooth finish. the side unit is added for the optimum storage with two sutters and open space duly covered with edge binding tape. the length of side unit is 900 mm ( ±10 ) with width of 400mm ( ±10 ) and height of 750mm ( ±10 ) . back storage unit is offered with three open shelfs on upper side and two either side openable door storage and four open box storage in between for the maximum and optimum utilasation. the overall diamensions of the back unit is l 1800mm ( ±10 ) x w 400mm ( ±10 ) x h 1800m ( ±10 ) . all the drawers, shutters, pedestals are provided with ss handles. each drawer is equiped with roller channel for smooth to&fro functioning. all wooden panels prime quality board with isi marked. 1 3 visitor chair providing and placing in position office chair. size h : 830 ±10, w : 560 ±10, d : 590 ±10. seat & back plywood made of 12mm hot pressed supported . understructure base of chair metal structure fixed type . seat & back are firmly connected to the base frame metal structure . chair max height 830mm . upholstery made of prime quality fabric . pha & machanism na . 480w x 450d base seat 70mm thick moulded with pu foam , d 45 kg / m3 , h 20 & 410w x 510h back seat 70mm thick moulded with pu foam , d 45 kg / m3 , h 20 . 485 / 560 arm rest fitted to the seat with armrest connecting brackets . base seat shell na . back seat shell na . l patta mild steel . beading finish with black pvc . arm rest height from seat 210mm . height from seat to ground 470mm . understructure all metal frame structure made of 25mm round metal pipe 2mm thick duly powder coated . all metal pieces shall be welded properly strongly and conformity with regulations . co2 welding shall be used . all metal shall be coated after being treated with at least three stages and cleaned from oil, grease, dust and other dirt using special thermal control coating for metal furniture 6 to form a layer of base coating of ( iron phosphating ) ( 0.4 – 0.8 ) gm / m² . automatic spray coating shall be applied to be followed by a drying process in a thermal furnace with suitable temperature and time for the process . thickness of coating ( 40 – 50 ) micron. 4 revolving chair providing and placing in position high back chair size h : 1160 ±10, w : 715 ±10, d : 715 ±10. seat plywood made of 12mm hot pressed supported . upholstery pvc structure moulded with prime quality high stretch fabric . pha ( gas lift ) 85mm ( tdc 152mm & bdc 67mm ) . understructure base revolving pedestal steel inserted pp base with pp hub cap . machanism torsion bar adjustment can be operated in seating position. seat & back are firmly connected to the base frame machanism. machanism provided upright position locking . chair max height 1160 & depth 715 . 450w x 470d base seat 80mm thick moulded with pu foam , d 45 kg / m3 , h 20 & 490w x 650h back seat 70mm thick moulded with pu foam , d 45 kg / m3 , h 20 . base seat shell na . back seat shell na . l patta mild steel . beading finish with black pvc . 450 / 530 arm rest fitted to the seat with armrest connecting brackets . arm rest height from seat 230mm . arm rest made of p.u . height from seat to ground 450mm . seating height can be adjusted with a pneumatic gas lift . pedestal pitch centre dia 715mm with casters . casters made of moulded black nylon metal bolt inserted & fitted with 5 nos . twin wheel casters 50mm dia . 1 5 almirah m.s sheet conforming to commercial quality cr 1, grade 340 of is 513:2008, number of doors ( nos ) =4, height of steel bookcase in mm ( ± 10 mm ) 1680 mm, width of steel bookcase in mm ( ±5 mm ) =910 mm, depth of steel bookcase in mm ( ± 3 mm ) =400 mm, stiffened pedestal height in mm ( ±2 mm ) =125, sheet thickness of shelves=1mm, sheet thickness of pedestal in mm=0.8mm, sheet thickness of door in mm=1mm, thickness of transparent glass in shutters in mm=4.0, type of lock= three way bolting device controlled by 6 lever lock, paint= powder coating 6 6 office table providing and placing office table with drawer unit. the buildup of the main table is free standing structure strength up with the help of minifix dowels and pins. the complete table made of high quality prelaminated particle board with approved laminate and finish as per approved shade. the table top would be 1200mm ( ±10 ) long made with 25 mm prelaminated particle board and 600mm / 750mm ( ±10 ) broad with two side gable ends with height of 750mm ( ±10 ) and width of 600mm / 750mm ( ±10 ) made up with 18 mm prelaminated particle board. the 18 mm thick modesty of the table is giving more strength and look to the table. all the sharp edges of the table top and gable ends are lipped with 2mm thick edge binding tapes for the smooth finish. the table is provided with attached one side pedestal. there is 3 no of drawers facility on single side attached pedestal.drawer pedestal is provided with central locking mechanism that allow all the drawers synchronized locked with one single key. each drawer is equiped with roller channel for smooth to&fro functioning. length of each drawer is 400mm ( ±10 ) and depth of 450mm ( ±10 ) and overall height is 675mm ( ±10 ) of the pdestal. all the drawers and storage is eqiped with ss handles to operate. all wooden panels prime quality board with isi marked. 2 7 chair providing and supplying mid back chair. the seat shall be made of 15mm thick hot pressed plywood upholstered with high resilience polyurethane foam 50mm thick having density 40kg / m³ with fabric tapestry 0.6mm thick and 235 gsm and the back shall be made of injection moulded polypropylene net cover upholstered with breathable mesh tapestry. the backrest of the chair shall be made by keeping the natural curvature of the spine and the armrest shall be used polypropylene arm completely joint with seat and back. for seating 4 durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal should have five legged injection moulded in 30% glass filled black nylon having pitch circle dia. 620 mm fitted with 5 nos. twin wheel castor. the castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ansi / bifma x5.1 2011 standard tested to perform 98, 000 cycles with 250lbs load. the seat size shall be 475±10 mm ( w ) x 490±10 mm ( d ) and back size shall be 450±10 mm ( w ) x 530±10 mm ( h ) from seat.overall height shall be = 885±10 mm & overall width / depth = 720±10 mm. 8 computer table overall size main table height width length material 750 mm 600 mm 1200 mm table top made from 18mm thick pre laminated isi mark mdf board & all materials details given in brief specification literature 1 leaping the edges of top and drawer front shall be sealed with tape 2mm and remaining with 0.8mm thick edge bands by hot process 2 storage fixed 1 drawer: overall size pedestal h675mm x w325mm x d585mmbody and drawer face made up of 18mm thick pre laminated isi mark mdf board with edges covered with 0.8mm and 2mm edge band. drawer inside unit made up of 11mm thick mdf board isi mark with edges covered with 0.8mm edge band running on good quality telescopic sliders 3 key board made up of 18mm thick pre laminated isi mark mdf board sliding on good quality 350 mm telescopic slider 4 handles high quality ss handles to be provided 5 shoes good quality levelling adjusters should be provided at the bottom 6 locking arrangement centre locking arrangement is to be provided for all drawers 3 9 computer revolving chair providing, supplying and placing of revolving computer chair. the seat and back are made up of 1.2 cm thick hot pressed plywood, upholstered with fabric and moulded polyurethane foam with pvc lipping all around. the seat is provided with a pre moulded inserts at the bottom for fixing mechnism and armrests. the back foam is designed with contoured lumbar support for extra comfort. back ) size: 40.0cm. ( w ) x 47.0cm. ( h ) seat size: 45.0cm. ( w ) x 42.0cm. ( d ) . the hr polyurethane foam is moulded with density=45+ / 2 kg / m cube and hardness load 16+ / 2 kgf as per is:7888 for 25% compression. the one piece armrests are injection moulded from black nylon. the armrests are fitted to the seat with armrest connecting brackets made of 0.5cm. thk. hr steel. the permanent contact mechanism is designed with 360° revolving type. 14° maximum back tilt only.upright position locking. tilt tension adjustment. the pneumatic height adjustment has an adjustment stroke of 11.0 cm.the bellow is 3 piece telescopic type and injection moulded in black polypropylene. the pedestal is injection moulded in black 30% glassfilled nylon and fitted with 5 nos. twin wheel castors. the pedestal is 62.0cm. pitch center dia. ( 72.0 cm with castors ) .the twin wheel castors are injection moulded in black nylon. all the above items should be as per photo, sketch , specifications & direction of engineer in charge. 3 10 white board ( 4x8 ft ) purpose writing , mounting type wall mounts frame ( all round framing ) with , writing board placed on n.a top surface materials ( used for white board surface ) melamine top surface material thickness 0.3 mm to 0.4 mm frame material anodized extruded aluminum alloy hollow section designation 63400 conforming to is 1285 ( with latest amendment ) core material n.a 12 core material thickness n.a dimension ( mm x mm ) 1200 x 2400 11 chair chair mechanism multi function tilt mechanism type of locking upright locking , number of arm movement n.a pedestal base nylon base , armrest material polypropylene seat material pressed and moulded with pu foam backrest is made of one piece injection moulded frame density of pu foam used in seat kg per cu meter ( ± 3 ) 40 density of pu foam used in backrest in kg per cu meter ( ±3 ) n.a backrest upholstered with mesh fabric , seat upholstered with mesh fabrics gsm / thickness of fabric ±5% ( gram / square meter ) 220 gram overall width ( ±10 mm ) 550 mm, backrest height ±15 mm 570 mm backrest width ±10 mm 500 mm , seat height ±10 mm 440 mm seat width ±10 mm 460 mm , seat depth ±10 mm 430 mm thickness of ms plate joining the under structure with seat 0.9 mm thickness of plywood used in seat ±1 ( mm ) 12 mm thickness of plywood used in backrest ± 1 ( mm ) n.a pedestal size ( diameter in mm ) ±10 mm 620 mm thickness of polyurethane foam used in seat in mm ( ±2 mm ) 45 mm thickness of polyurethane foam used in backrest in mm ( ( ±2 mm ) 25 mm warranty period in number of years 1 years 12 12 table providing and placing office table with drawer unit. the buildup of the main table is free standing structure strength up with the help of minifix dowels and pins. the complete table made of high quality prelaminated particle board with approved laminate and finish as per approved shade. the table top would be 1200mm ( ±10 ) long made with 25 mm prelaminated particle board and 600mm / 750mm ( ±10 ) broad with two side gable ends with height of 750mm ( ±10 ) and width of 600mm / 750mm ( ±10 ) made up with 18 mm prelaminated particle board. the 18 mm thick modesty of the table is giving more strength and look to the table. all the sharp edges of the table top and gable ends are lipped with 2mm thick edge binding tapes for the smooth finish. the table is provided with attached one side pedestal. there is 3 no of drawers facility on single side attached pedestal.drawer pedestal is provided with central locking mechanism that allow all the drawers synchronized locked with one single key. each drawer is equiped with roller channel for smooth to&fro functioning. length of each drawer is 400mm ( ±10 ) and depth of 450mm ( ±10 ) and overall height is 675mm ( ±10 ) of the pdestal. all the drawers and storage is eqiped with ss handles to operate. all wooden panels prime quality board with isi marked. 12 13 notice board ( 3x4 ft ) width of board in mm 900 mm colour ( front / display layer ) red height of board in mm 1200mm front cover material of board acrylic ( minimum 2 mm thickness ) rear panel material of board laminated sheet overall pinability depth of board in mm 10 millimeter core material thickness in mm ( n >= 9 ) 9 millimeter orientation portrait / landscape type of front cover without front cover warranty in years 2 2 14 faculty chair chair with ergonomic design, comfortable & aesthetically appealing. ø the seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg / m³ in seat and 40mm thick having density 40kg / m³ in back. ø the same shall be upholstered with fabric tapestry 1mm thick and 300 gsm. ø the back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the 10 spine with lumbar support. ø the seat and back shall be arrested together with 50 60μ thick powder coated hr steel spine and the armrest shall be used black integral polyurethane arm with metal insert completely joint with seat and back. ø for seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. ø the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. ø the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. ø the pedestal should be five legged injection moulded in black 30% glass filled nylon having pitch circle dia 700±15 mm and fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ansi / bifma standards x5.1 2011 tested to perform 98, 000 cycles with 250lbs load. ø the seat size shall be 475±10 mm ( w ) x 460±10 mm ( d ) and back size shall be 460±10 mm ( w ) x 550±10 mm ( h ) from seat. ø overall height shall be 950±10 mm, overall width ( arm ) 545±10 mm, base width / depth 760±10 mm. 15 table big providing and placing in position office table. overall size of the table shall be 1800 w mm ( ±10 ) x 750 d mm ( ±10 ) x 750 h mm ( ±10 ) .office table top ducknose postform 25mm thick wooden board with 2mm thick pvc edgebanded finish with as per approved laminate shade . mobile pedestal size 400w ( ±10 ) x 450d ( ±10 ) x 680h ( ±10 ) . table top supported understructure of table gable end made of prime quality 18mm thick plpb board. mobile drawer top 18mm thick wooden board with 0.8mm thick edgebanded one side ducknose postform . mobile drawer used sliding telescopic channel with all fittings & shutter used c frame handles . mobile drawer move on twin wheel casters 50mm dia . casters made of moulded black nylon metal bolt inserted & fitted . all wooden panels cleaning corner knitted finish . all wooden panels , gables & modesty fix joints with minifix dowels & other fitting equipment. the side unit overall size is 1200mm ( ±10 ) x 400mm ( ±10 ) x 675mm ( ±10 ) . all wooden panels prime quality board with isi marked. 2 16 rack the complete structure is made of 18 mm prelaminated particle board. constructed with the help of minifix dowels and pins. all sharp edges of top and shelfs front are lipped with edge binding tape 2mm by hot process. the rack is designed to provide six shelves and 8 compartments. overall dimensions h1980x w 910x d 480mm. 10 17 three seater waiting sofa three seater sofa of size 1880 x 788 x 635 mm. 12mm ply used made of back & base . upholstery made of prime quality rexine black . base seat moulded with foam , ( 90mm + 21mm ) thick , d 28kg / m3 . back seat moulded with foam , 45 thick , d 28kg / m3 . arm rest moulded with foam , 45 thick , d 28kg / m3 . back inserted foam , 21 thick , d 28kg / m3 . ends sofa structure pvc caps . sofa l brakets & base frame made of prime quality ms . fastners nut bolt 4nos . size m8 x 38mm . sofa structure shall have ms spring base . understructure made of base frame 20 x 20 square ss pipe 1.2mm thick . support frame made of 12mm dia round ss pipe 1.2mm thick . side frame made of 25mm dia round ss pipe 1.6mm thick . pinewood 25w x 25mm thick . seat height from bottom to base 458mm . back height from base seat to top 356mm . hand rest width 150mm . all ss pipes shall be welded properly strongly and conformity with regulations . sofa structure stailness steel pipe shall be abrasive polished external finished . 3 18 study table providing and placing as office furniture office table constructed with metal frame and mdf board. the table top made of thick 25mm mdf board with length of 2400 mm ( ±10 ) and width of 1200 mm ( ±10 ) and height 750 mm ( ±10 ) . all sharp edges of top are lipped with edge binding tape 2mm. the table top is fitted with nuts and screws on the four leg metal frame made of ms square pipe of 38 x 38 x 1.2 mm thick. all the legs are fitted with high quality 10 rubber shoes. the overall dimensions of the table are l 2400mm ( ±10 ) x w 1200mm ( ±10 ) x h 750 mm ( ±10 ) . all wooden panels prime quality board with isi marked. 19 chair overall size 480w x 490d x 780h . base seat & back made of moulded pp structure supported ( single piece moulded seat & back shell ) . understructure base of chair round ss pipe structure fixed type. understructure base fixed type 19mm dia ss round pipe 1.2mm thick. machanism & pha ( gas lift ) na . seat & back are firmly connected to the base frame . chair max height 780 & depth 490mm. 440w x 410d base seat moulded with pp structure & 440w x 390h back seat moulded with pp structure. height from seat to ground 420mm . all ss round tube pieces shall be welded properly strong...