Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

34063681 tender for electrification of line under edd hamirpur 2 cartage of poles from store center hamirpurfrom any other place to the respective site of work through the kachha pacca road including the work of its loading & unloading at the respective ends also including the work of dragging etc. and also including the cost of labor, t & p carrier etc. required for proper completion of work. 3 8.5 m pcc pole 4 11 m stp pole 5 cartage ofline material viz. weasel conductor, gi earth wire, cross arm, angle, channel, insulator, clamps and other line material from store centerany other place to the respective site of work through the kachha pacca road includingthe work of its loading & unloading at the respective ends, including the work ofdragging etc. and also including the cost oflabor, t & p and carrier etc. required for proper completion of work. 6 erection of single support poles including complete h.t. / l.t. fittings as per resspo manual and as per direction of engineer inchargeincluding the cost oflabor, t&p and carrier etc. required for proper completion of work. 7 8.5 m pcc pole 8 11 m stp pole 9 erection of double pole on poles including the work of complete h.t. fittings as per resspo manual and as per direction ofengineer incharge including the cost oflabor, t&p and carrier etc. required for proper completion of work. 10 11 m stp pole 11 groutingof poleas per resspo manual and as per direction of engineer incharge includingthe cost oflabor, t&p and carrier etc. required for proper completion of work. 12 erection and grouting of stay set including the work of nuzzling etc. as per resspo manual. and also including the cost of all grouting material , labour t&p etc.required for proper completion of work. 13 fixing of ear thingrod as per resspo manual and as per direction of supervising engineer. 14 laying, sagging, stringing, binding and jumpring etc. of acsr weasel conductor new / oldon the newly erected pole as per resspo manual and as per direction of supervising engineer. 15 lying of stone pad 300x300x75 mm 16 laying of top channel 100x50x2240 mm 17 laying of ms angle 65x65x6 mm bracing with 4 clamps 18 laying of 11 kv disc insulator with pin 19 laying of e bracket 20 laying of 11 kv pin isulator with pin 21 laying of clamp of channel 22 laying of danger board with clamp for 11 kv 23 layin of pg clamp 24 laying of barbed wire 25 alluminium paint of pole painting 26 red oxide paint of pole painting 27 layin of t off channel 28 laying of ms angle 65x65x6 mm 29 laying of gaurding angle 30 laying of eye bolt 31 laying of g.i. wire 6 swg 32 laying of g.i. wire 8 swg 33 laying of v type cross cross arm 34 layinf of f bracket with bolt 35 dismantling of single support and all accessories 36 dismantling of old line, acsr weasel conductor...

Indian Oil Corporation Limited - Uttar Pradesh

34056592 supply and painting on criss cross pipelines with heat resistant aluminium paint including making of bands, arrows, letter writing etc inside the dyke area at kanpur terminal => limited...

Aligarh Muslim University - Uttar Pradesh

34044489 painting with acrylic exterior paint of boundary wall, distempering and aluminium paint at m.a. library and kennedy hall and inside mazhar jama masjid on the occasion of sir syed day. based on dsr2018 => limited...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

33994605 electric work work related to issuing the applied combination on the online portal under the complete deposit scheme item. 2 carriage of fallowings from esc. bsr to pit site on kachcha pacaa road including loading and unloading chagres at both ends, rcquricd for proper completion of work, distance about to 60 kms. 3 s.t pole 11 mtr. long 4 pcc pole 8.5 mtr long. 5 carriage of all line material from store center bsr to j.e store sub station as acsr weasel conductor, abc conductor gi wire, earth wire. m.s. chanel, angle, stay & earthig rods, barbed wire. disc insulator etc. 6 erection ofsingle pole support including complete 1 it fittings as per respo manual and as per direction of engineer in charge including the cost of labour, t&p and carrier etc. required for proper completion of work. 7 erection of double pole / scation pole support including complete 1 it fittings as per respo manual and as per direction of engineer in charge including the cost of labour, t&p and carrier etc. required for proper completion of work. 8 grouting of single support shall be grouted with cement, sand and birck ballast / stone ballast in ratio 1:4:8 =30x3030 cms. including the cost of cement, sand, birck ballast / stone ballast, etc. as per actual size requirement, as per respo manual and as per direction of engineer in charge including the cost of labour, t&p and carrier etc. required for proper completion of work. 9 grouting of double pole support shall be grouted with cement, sand and birck ballast / stone ballast in ratio 1:4:8 =30x3030 cms. including the cost of cement, sand, birck ballast / stone ballast, etc. as per actual size requirement, as per respo manual and as per direction of engineer in charge including the cost of labour, t&p and carrier etc. required for proper completion of work. 10 carriage of all line material from j.e store sub station to pit site acsr weasel conductor, abc conductor gi wire, earth wire. m.s. chanel, angle, stay & earthig rods, barbed wire. disc insulator etc. 11 cutting / drilling / welding of ms angle iron for making guarding angle size 65x65x6 / 50x50x6 mm including the work of fixing the bracket on pcc / st pole for construction of the line. 12 carriage of 11 kv ct / pt metering polemounted unit varius ratio 13 carriage and installation of 11 kv pilferresistant metering cubicle with out cable termination kit 14 mounting of 11 kv ct / pt unit varius ratio 15 making / filling of 11 kv cable jointing kit varius sizexlpe cable 16 carriage of t / ffrom esc. bsr to pit site on kachcha pacaa road including loading and unloading chagres at both ends, rcquricd for proper completion of work, distance about to 60 kms. 17 fixing of 11 kv stay rod with stay wire in proper way with nozelling 18 grouting of 11 kv stay rods 19 laying, sagging. stringing and binding and jumpering of 11 kv xlpe cable 3*70 square mm & outher size newly erected pole as per respo manual and as per direction of supervising engineer. it includes the cost of labour, t&p, carrier etc. requried for proper completion of work. 20 laying, sagging. stringing and binding and jumpering of acsr weisal , rabbit, dog newly erected pole as per respo manual and as per direction of supervising engineer. it includes the cost of labour, t&p, carrier etc. requried for proper completion of work. 21 acsr weisal conductor 22 abc cable 3x50sq.mm. 23 fixing of 11kv cross arm 24 fixing of earthing rod 25 fixing of pin insulator and pin with nut 26 fixing of g.i pipe 6 dia 27 fixing of g.i. wire 6 swg & 10 swg 28 fixing disc insulator and disc feeting 29 installation of 11 kv tvm 3p4w 30 the folloing material is required to be supplied by the contractor. 31 holding clamp 32 11kv cable jointing kit 3*70 square mm xlpe cable 33 pcc pole clamp 34 single phase lt box 35 dead & clamp 36 i hook 37 suspantion clamp 38 stone pad 300x300x75 39 barbed wire 40 danger board with nut and clamp 41 concrete pole and stay 42 clamp with nut and bolt 43 red oxide paint 44 aluminium paint 45 bolt & nut off size....

Nagar Panchayat - Uttar Pradesh

33990832 tender for led light automigation work 2 supply and laying aluminium conductor pvc inslulated armoured seved sheathed cable 1100 volts grade of pole, suitable size of as directed by the engineer incharge completer in all respect. 16mm 02 core. 3 supply and fixing of safety switch 10 kw complete in all respect. 4 supply and fixing of plain or pin type copper tin plated cable socket to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction engineer in charge. 5 suppy and erection of d clamps of 50mm x 6mm flat iron on steel tubular poles / steel rail poles with bolts, nuts etc. complete in all respect including painting with aluminium paint and all fitting 6 supply and fixing of wire fixer tape....

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

33934954 safely cartage of stpoles sp 55, 11 mtr.long fromesc, sreto the site of workincluding loading & unloading at both ends. ( distance upto 40 km. ) 3 safely cartage of complete line material ( except st poles, xlpe cable, vcb, ct&pt unit & mitringcubical ) from esc, sreto the site of work / dumping place / other place to local dumping ground or 33 kv s / s / other place of siteincluding loading & unloading at both ends. ( dist. upto 40 km. ) 4 safely cartage of11 kvxlpe of size 3x120 sq mm cable fromesc, sre to the site of work including loading & unloading at both ends. ( distance upto 40 km. ) 5 safe cartage of 11 kv ct / pt unit from esc sre to the site of work including loading & unloading at both ends. ( dist. upto 40 km. ) 6 safe cartage of11 kv metering cubicalfrom esc sre to the site of work including loading & unloading at both ends. ( dist. upto 40 km. ) 7 safe cartage of11 kv vcbfrom esc sre to the site of work including loading & unloading at both ends. ( dist. upto 40 km. ) 8 erection of single stpoles sp 55, 11 mtr. longwith complete fitting of all accessories of 33 kv line as per respo specifications. 9 fabrication and erection of double pole sp 55, 11 mtr. & sp 72, 13 mtr. long st poles with complete fittingofbracings & other accessories as per respo specifications. 10 fixing of 11 kv stay rods by digging of pits in block of 600x600x300 mm. &with new brick and nozzling of stay wire 7 / 10 swg and fitting the same on the pole 11 laying, lifting, stringing, sagging jumpering & binding of acsr rabbit conductor on st polefor 11 kv line as per respo specifications. 12 earthing of st poles by earthing rod 20x2500 mm as per respo specifications. 13 concreting of st poles sp 55, 11 mtr.long with cement concreting in bolck of 600x600x1500 mm. in ratio 1:4:8 with cement, sand and brick ballast size 1x1.5 with plinth. 14 providing and fixing x arm holding clamp, channel & angle clamp, & guarding clamp for st poles made of new ms flat size 50x6 mm. 15 providing and fixingf bracket / clamp, for st poles made of new ms flat size 50x6 mm. 16 providing and fixingstay clamp, for st poles made of new ms flat size 50x6 mm. 17 providing and fixingbracingclamp, for st poles made of new ms flat size 50x6 mm. 18 providing and fixinge clampfor st poles made of new ms flat size 50x6 mm. 19 providing and fixing t channelclampfor st poles made of new ms flat size 50x6 mm. 20 providing and fixing d / p clampfor st poles made of new ms flat size 50x6 mm. 21 providing and fixing guarding clamp for st poles made of new ms flat size 50x6 mm. 22 providing and fixing pg clamp for rbbit conductor. 23 providing and fixing of stone ped 300x300x75 24 providing and fixing ms nuts & bolts & washers off size 25 providing and fixing of gi barbed wire on the each pole. 26 providing and fixing of g.i. pipe 100 mm dia 3.5 mtr. long at the both side of double pole with clamps. 27 providing of hdpe pipe 100 mm dia 28 providing and fixing of number plate with clamp on the each pole. 29 providing and fixing 11 kv danger board withclamp for st poles made of new ms flat size 40x5 mm with nuts & bolts. 30 providingof alluminium paint ( british / asian / enamel paint ) 31 providing ofred oxide paints ( british / asian / enamel paint ) 32 painting ofst poles 11 mtr, sp 55with 2 coats of synthetic enamel paint after one coat of ready mix primer as well as rubbing / cleaning of surface as required for proper completion of work. and remaining by aluminium paint including all channels / clamps etc. 33 laying, lifting, stringing, saggingof 11 kv xlpe cable of size 3x120 sq mm on st polefor over hed line as per respo specifications. 34 digging of trench 1.5 mtr. deepand laying of 2 no. parreral hdpe pipe 100 mm dia on 1 meter distance by drill machine. 35 laying of11 kv xlpe cable 3x120sq mm in the hdpe pipe 100 mm dia on 1 meter distance. 36 providing of 11 kv heat shrinkable jointing kitoutdoor & indoor of size 3x120 sq mm. ( denson make, raychem make ) 37 fixing & making of 11 kv cable heat shrinkable terminationskits of size 120 sqmm ofoutdoor & indoor side. 38 guarding of span of 11 kv line on road crossing / river crossing and ht / lt line crossing with g.i. wire as per respo specifications. 39 off shooting of tree branches for clearence of proposed33 kv line. ( approx 5 km line ) 40 safe installation of11 kv ct / pt unit on the double pole with complete fittings including making connections and commissioning. 41 safe installation of11 kv metering cubical in the room with complete fittings including making connections and commissioning. 42 shifting and fixing and installation of new vcb out going panel in control room ats / s complete in all respect and fixing bus bar and cable connection with proper alignment. 43 fabrication charges of angle 44 earthing of11 kv vcb pannel by boring of 60 ft. deep& fixing of 60 ft.g.i. pipe 11 / 2” dia ( jindal class b ) and connecting with g.i. strip of size 40x5 mm and g.i. wire. at bottom of g.i. pipe to the t / f providing of required charcoal & salt in the pipe....

Uttar Pradesh Power Transmission Corporation Limited - Uttar Pradesh

33926927 providing and fixing of 160 watt led light fitting in switchyard at 132 kv substation malwan under electy. trans. division fatehpur. 1 providing and fixing of new generation energy saving and environment friendly long life versatile pressure die cast aluminium outdoor laminator with high power 160 watt leds as light source and along with electronic driver complete fitting suitable for 220 v input supply of isi make havells / philips / bajaj / hpl, in all respect including with its fixing with pole at 132 kv s / s malwan. 2 supply and fixing of bended pipe with its clamp for fixing one coat of red oxide primer and asian / berger / shalimar make aluminium paint in two coat after cleaning of rust, dust and surface including the cost of all material / t&p and labor cost. 3 laying of 2x2.5 mm2 cable from ltd to every light fitting in the ground ( 10cm below ) and over the gantry through the banded pipe and termination of same & checking of all fitting for proper lightening. 4 supply and fixing of junction box of size 100x200x15mm at the pole having suitable mcb of 6 / 10 / 20 amp inside the box with cut out for phase and neutral to provide single phase ac supply to the leds light....

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

33901838 balance work of 33 / 11kv substation sehud ( auraiya ) and related 33and11 kv lines 1 33kv lightning arrestor 2 33 kv vcb with ct 200 / 100 / 1a alongwith structure complete with plinth & foundation 3 33kv 1 ph pt 33kv / 110 v 4 33kv control panel for single t / f without differential relay 5 11 kv vcb switchgears with incoming ctr 600 / 300 / 5a, 350mva 6 11 kv vcb switchgears with outgoing ctr 200 / 100 / 5a, 350 mva 7 24 volt battery and battery charger with cabinet complete 8 11 kv 3 core al. xlpe insulated 3x300 mm sq. cable 9 11 kv 3 core al. xlpe insulated 3x120 mm sq. cable 10 control cable ( copper ) 4x2.5 mm sq. 11 control cable ( copper ) 2x2.5 mm sq. 12 90 lbs rail pieces for transformer 44.64 kg / m 13 barbed wire fencing with gate. 14 lighting of substation building including supply and fixing of fittings ( as per specification ) 15 t & p of sub station & switchgears ( as per specification ) 16 4.5 kg. co2 fire extinguisher, portable type 17 5 kg. dry chemical powder fire extinguisher, portable type 18 rubber matting 20 sq. mm. thick size ( 1 x 2 mtr. ) 19 s / s name board ( smc ) with stand as per rec specification. 20 chemical pipe earthing as additional earthing ( for t / f, la, ct & pt ) 21 11kv xlpe cable ( 3x300 sq.mm. ) heat shrinkable jointing kit boxes mounted with switchgears and transformers. 22 11kv xlpe cable ( 3x185 sq.mm. ) heat shrinkable jointing kit boxes mounted with switchgear indoor. 23 11kv xlpe cable ( 3x185 sq.mm. ) heat shrinkable jointing kit outdoor 24 laying of 3x300 & 3x120 sq. mm, 11 kv, xlpe cable ug includnig cost of sand and bricks 25 painting of s / s structure 26 9 meter long pcc pole 27 11 meter long stp ( sp 55 ) 28 acsr dog conductor 29 33 kv xlpe insulated al. cable of size 3x300 mm2 30 33 kv pin insulator 31 11 kv disc. insulators b&s type 70 kn 32 33 kvpin with nuts 33 33 kv disc fitting b & s type ( 70 kn ) 34 33 kv stay rod 20x1800 mm 35 33 kv steel x arm v type ( ms channel 100 x 50 x 6 mm ) 36 33 kv cross arm holding clamps with bolts & nuts 37 f bracket for 33 kv line 38 e bracket for 33 kv line 39 ms angle iron 65x65x6mm, 4300 mm long bracing with 4 clamps 40 m.s. top channel 125x65x6 mm, 3200 mm ( 10.7kg / mt ) with clamp, bolts, nuts and washers 41 pg clamps for raccoon / dog 42 33 kv stay clamp 43 m.s. guarding angle 75x75x6 mm, 2200 mm long with holding clamp, packing piece, nut & bolts etc. 44 g.i. pipe 6 dia. ( class b ) 45 stay wire 7 / 8 swg 46 g.i. wire no. 6 swg 47 g.i. wire no. 8 swg 48 alluminium jointing sleeves for acsr dog 49 33 kv number plate with clamp and nuts & bolts 50 33 kv danger board with clamp and nuts & bolts 51 alluminium paint for stp 52 red oxide paint for stp 53 turn buckle 54 eye bolt 55 heat shrinkable jointing kit outdoor for 33 kv 3x300 sq. mm xlpe cable 56 supply and laying of gi pipe class c ( 160 mm dia. ) for ug laying of 3x300 sqmm 33 kv xlpe cable ( pipe to be laid by hdd method ) 57 supply and laying of hdpe pipe ( 160 mm dia. ) for ug laying of 3x300 sqmm 33 kv xlpe cable ( pipe to be laid by hdd method ) 58 grouting of pcc 9.0 mtr pole ( 0.286 cum ) 59 concreting of supports ( 11 mtr. stp ) 60 concreting of 33 kv stay road 20x1800 mm 61 tree cutting compensation 62 digging of trench by excavation of earth, laying of cable, laying bricks to cover the cable and filling of sand & earth ramming and dressing properly with complete job for laying 33 kv xlpe cables of sizes 3x300 sq. mm including cost of bricks, sand, clamps etc. 63 laying of 33 kv 3x300 sqmm. xlpe cable underground in g.i. pipe 64 laying of 33 kv 3x300 sqmm. xlpe cable underground in hdpe pipe 65 laying of 33 kv 3x300 sq.mm xlpe cable in g.i. pipe on double pole 66 11kv / 0.433 kv, 3 phase, 63 kva transformer ( bee standard, 3 star rating self protected type ) , al. wound 67 8.5 mtr. long. pcc poles 68 acsr rabbit conductor 69 lt pvc cable3.5x70 sq.mm. 70 lt aluminium xlpe cable of size 1x50 sq.mm. 71 11kv tpmo ( as per specification ) 72 9 kv ligntening arrestor 73 11 kv pin with nuts & washers 74 11kv 45 kn disc fitting t&c type complete 75 g.i. stay rod 16x1800mm 76 11 kv pin insulators 77 11kv disc insulator t&c type 45 kn 78 m.s. top channel 100x50x6 mm., 2240 mmlong with clamp, nuts & bolts. 79 ms angle iron 50x50x6 mm bracing with 4 clamps 80 11kv v type cross arm ( angle 65x65x6mm ) 81 tee off channel 100x50x1300 mm with clamp, nut & bolt 82 guarding cross arm ( m.s.angle 65x65x6mm / 1.6 meter long ) , 5.8kg. / m=9.28kg. 83 f bracket for fitting top insulator with bolts & nuts 84 e brackets with nuts & bolts 85 clamp for fixing x arms with bolts and nuts 86 11 kv stay clamp 87 holding clamps for top channel tpmo & fuse set etc. with bolts & nuts 88 11 kv smc danger board with clamps and bolts 89 p.g. clamp for acsr rabbit / weasel 90 bolt, nuts & washer 91 stay wire 7 / 10 swg 92 g.i. wire no. 16 swg 93 g.i. barbed wire 94 stone pad ( 300x300x75mm ) 95 alluminium binding wire 6 swg 96 g.i. pipe 6 dia. ( class b ) 97 eye bolts for gaurd wires and lt cable catenary wires 98 painting number mark with paint ( quote in erection price only ) 99 aluminium jointing sleeves for acsr rabbit / weasel 100 11 kv xlpe cableheat shrinkable jointing kit outdoor for 11 kv 3x300 sq. mm xlpe cable 101 11 kv xlpe cableheat shrinkable jointing kit outdoor for 11 kv 3x120 sq. mm xlpe cable 102 earthing complete for t / f neutral and l.a. ( chemical pipe earthing ) 103 earthing of pole by ms earthing rod of 20x2500 mm. and 6 swg earthing wire etc. 104 grouting of 8.5 m long pcc poles ( 0.268 cum ) 105 concreting of stay rod ( 16x1800 mm. ) 106 road restoration charges for pucca road crossing 107 road restoration charges for kuchha road crossing 108 ac distribution box 109 dcdistribution box 110 sundry stores as per specification. 111 control room building, boundry, development of site, water sanitation etc. ( as per schedule 2 ) ...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

33901067 work for line shifting under eudd i and ii sre 1 a: schedule of work against under saharanpur smart city project installation of signal light and camera shifiting of high voltage line sadar tiraha, under eudd i sre.safe carriage of 13 mtr long st pole ( sp 70 ) from pvvnl, store / works place / dump store to site including loading & unloading both ends. 2 safe carriage of line material including 600 mtr. acsr dog conductor from pvvnl, store / work place / dump store to site including loading & unloading at both ends. 3 errection of 13 mtr. longst pole with proper alignment excavation of foundationpit in size of 75x45 cm. having depth of 1 / 6th of the full length of the support ( pole ) providing and laying of stone pad ( 300x300x75mm. ) in the bottom of the pit as per respo norms. 4 grouting of pole support in cc 1:4:6 ( cement, send, and 40 mm. brick ballast ) grouting will be done in the block of size 45 x45 cm x 1 / 6th of full length of support upto ground leavel as per respo norms. 5 fixing of channel / angle / x arm on st poles as per respo norms 6 providing & fixing of holding clamp with nut bolts for st poles made by new ms angle 50x6mm as per respo norms. 7 earthing of pole support with ms earth rod of ( 20x2500 ) mm long including excavation of pit and driving ms rod 3.0a part from support and 0.5 m below the ground level and connecting below the earth electrodes with the help of g.i. wire tighting with nuts and bolts as per respo norms. 8 laying and sagging of acsr dog conductor including binding with all accessories on pole as per respo norms. 9 grouting of stay rods ( 20x1800mm ) including all works of excavation. cement concrete in sizw of ( 0.60x0.60x0.3 ) m in the ratio of 1:4:6 ( cement, sand and 40mm crick ballast ) including back filling of soil and proper ramming etc. 10 fixing, tighteing and nozelling of stay wire with stay rod and saty insulators with the ploe of required tension by provinding stay clamps, nuts, bolts etc. 11 dismantling the old existing line and remove of acsr dog conductor from all phases on the line, making the bundle. 12 dismantling of existing st pole with all accessories 13 carriage of03 nos. pole and all dismantaled line material from site topvvnl, store including loading & unloading at both ends. 14 providingfirst class quality approved aluminium and red oxide paints and painting two coats aluminium paint, one coats red oxide paint of pole as per respo norms. 15 b : schedule of work against under saharanpur smart city project installation of signal light and camera shifiting of high voltage line diwani tiraha, under eudd i sre.safe carriage of 13 mtr long st pole ( sp 70 ) from pvvnl, store / works place / dump store to site including loading & unloading both ends. 16 safe carriage of line material including 200 mtr. acsr dog conductor from pvvnl, store / work place / dump store to site including loading & unloading at both ends. 17 errection of 13 mtr. longst pole with proper alignment excavation of foundationpit in size of 75x45 cm. having depth of 1 / 6th of the full length of the support ( pole ) providing and laying of stone pad ( 300x300x75mm. ) in the bottom of the pit as per respo norms. 18 grouting of pole support in cc 1:4:6 ( cement, send, and 40 mm. brick ballast ) grouting will be done in the block of size 45 x45 cm x 1 / 6th of full length of support upto ground leavel as per respo norms. 19 fixing of channel / angle / x arm on st poles as per respo norms 20 providing & fixing of holding clamp with nut bolts for st poles made by new ms angle 50x6mm as per respo norms. 21 earthing of pole support with ms earth rod of ( 20x2500 ) mm long including excavation of pit and driving ms rod 3.0a part from support and 0.5 m below the ground level and connecting below the earth electrodes with the help of g.i. wire tighting with nuts and bolts as per respo norms. 22 laying and sagging of acsr dog conductor including binding with all accessories on pole as per respo norms. 23 grouting of stay rods ( 20x1800mm ) including all works of excavation. cement concrete in sizw of ( 0.60x0.60x0.3 ) m in the ratio of 1:4:6 ( cement, sand and 40mm crick ballast ) including back filling of soil and proper ramming etc. 24 fixing, tighteing and nozelling of stay wire with stay rod and saty insulators with the ploe of required tension by provinding stay clamps, nuts, bolts etc. 25 providingfirst class quality approved aluminium and red oxide paints and painting two coats aluminium paint, one coats red oxide paint of pole as per respo norms. 26 dismantling the old existing line and remove of acsr dog conductor from all phases on the line, making the bundle. 27 dismantling of existing st pole with all accessories 28 carriage of 03 nos. pole and all dismantaled line material from site topvvnl, store including loading & unloading at both ends. 29 c : schedule of work against under saharanpur smart city project conversion of lt line in to abc in purani chungi near kissan dairy to road crossing causingh hinderance commisioning of pole for signal light and camera.under eudd ii sre.safe carriage of 11 mtr long st pole ( sp 55 ) from pvvnl, store / works place / dump store to site including loading & unloading both ends. 30 safe carriage of line materialfrom pvvnl, store / work place / dump store to site including loading & unloading at both ends. 31 safe carriage ofabc 3x95+1x70+1x16 sq. mmfrom pvvnl, store / work place / dump store to site including loading & unloading at both ends. 32 errection of 11 mtr. longst pole with proper alignment excavation of foundationpit in size of 75x45 cm. having depth of 1 / 6th of the full length of the support ( pole ) providing and laying of stone pad ( 300x300x75mm. ) in the bottom of the pit as per respo norms. 33 grouting of pole support in cc 1:4:6 ( cement, send, and 40 mm. brick ballast ) grouting will be done in the block of size 45 x45 cm x 1 / 6th of full length of support upto ground leavel as per respo norms. 34 fixing of channel / angle / x arm on st poles as per respo norms 35 earthing of pole support with ms earth rod of ( 20x2500 ) mm long including excavation of pit and driving ms rod 3.0a part from support and 0.5 m below the ground level and connecting below the earth electrodes with the help of g.i. wire tighting with nuts and bolts as per respo norms. 36 providing & fixing of holding clamp with nut bolts for st poles made by new ms angle 50x6mm as per respo norms. 37 providing & fixing of suspention clamp for abc as per respo norms. 38 providing & fixing of piercing clampas per respo norms. 39 providing & fixing of j hook as per respo norms. 40 laying and sagging of abc cable including binding with all accessories on pole as per respo norms. 41 providingfirst class quality approved aluminium and red oxide paints and painting two coats aluminium paint, one coats red oxide paint of pole as per respo norms. 42 fixing the 3 phase distribution box as per respo norms. 43 d : schedule of work against under saharanpur smart city project shifting of 33kv line at ambedkar chowk, srefor signal light and cameraunder eudd ii sre.safe carriage of 13 mtr long st pole ( sp 70 ) from pvvnl, store / works place / dump store to site including loading & unloading both ends. 44 safe carriage of line materialfrom pvvnl, store / work place / dump store to site including loading & unloading at both ends. 45 safe carriage ofxlpe cable 3x300 sq mm.from pvvnl, store / work place / dump store to site including loading & unloading at both ends. 46 errection of double pole with 13 mtr. longst poleproper alignment excavation of foundationpit in size of 75x45 cm. having depth of 1 / 6th of the full length of the support ( pole ) providing and laying of stone pad ( 300x300x75mm. ) in the bottom of the pit as per respo norms. 47 grouting ofpole support in cc 1:4:6 ( cement, send, and 40 mm. brick ballast ) grouting will be done in the block of size 45 x45 cm x 1 / 6th of full length of support upto ground leavel as per respo norms. 48 grouting of stay rods ( 20x1800mm ) including all works of excavation. cement concrete in sizw of ( 0.60x0.60x0.3 ) m in the ratio of 1:4:6 ( cement, sand and 40mm crick ballast ) including back filling of soil and proper ramming etc. 49 fixing, tighteing and nozelling of stay wire with stay rod and saty insulators with the ploe of required tension by provinding stay clamps, nuts, bolts etc. 50 providing & fixing of holding clamp with nut bolts for st poles made by new ms angle 50x6mm as per respo norms. 51 providing & fixing of branching clamp for sp 70 stp poles as per respo norms. 52 laying of 3x300 sq. mm 33kv cable as per respo norms. 53 filling of cable jointing kit out door 33 kv as per respo norms. 54 proper making ht connection as per respo norms. 55 providing & laying hdpe pipe for 33kv as per respo norms. 56 providingfirst class quality approved aluminium and red oxide paints and painting two coats aluminium paint, one coats red oxide paint of pole as per respo norms. 57 providing & fixing of danger board with clamp, nut and bolts. 58 providing & fixing of number plate with clamp, nut and bolts. 59 supply & fixing of barbed wire on the poles. 60 supply fixing and clamping of g.i pipe 150mm dia 02 mtr. height. 61 e : schedule of work against under saharanpur smart city project shifting of 11kv line at ambedkar chowk, srefor signal light and cameraunder eudd ii sre. safe carriage of 11 mtr long st pole ( sp 55 ) from pvvnl, store / works place / dump store to site including loading & unloading both ends. 62 safe carriage of line materialfrom pvvnl, store / work place / dump store to site including loading & unloading at both ends. 63 safe carriage ofxlpe cable 3x185 sq mm.from pvvnl, store / work place / dump store to site including loading & unloading at both ends. 64 errection of double pole with 11 mtr. longst poleproper alignment excavation of foundationpit in size of 75x45 cm. having depth of 1 / 6th of the full length of the support ( pole ) providing and laying of stone pad ( 300x300x75mm. ) in the bottom of the pit as per respo norms. 65 grouting of stay rods ( 20x1800mm ) including all works of excavation. cement concrete in sizw of ( 0.60x0.60x0.3 ) m in the ratio of 1:4:6 ( cement, sand and 40mm crick ballast ) including back filling of soil and proper ramming etc. 66 fixing, tighteing and nozelling of stay wire with stay rod and saty insulators with the ploe of required tension by provinding stay clamps, nuts, bolts etc. 67 grouting ofpole support in cc 1:4:6 ( cement, send, and 40 mm. brick ballast ) grouting will be done in the block of size 45 x45 cm x 1 / 6th of full length of support upto ground leavel as per respo norms. 68 providing & fixing of holding clamp with nut bolts for st poles made by new ms angle 50x6mm as per respo norms. 69 providing & fixing of branching clamp for sp 55 stp poles as per respo norms. 70 laying of 3x185 sq. mm 11kv cable as per respo norms. 71 filling of cable jointing kit out door 11 kv as per respo norms. 72 proper making ht connection as per respo norms. 73 providing & laying hdpe pipe for 11kv as per respo norms. 74 providingfirst class quality approved aluminium and red oxide paints and painting two coats aluminium paint, one coats red oxide paint of pole as per respo norms. 75 providing & fixing of danger board with clamp, nut and bolts. 76 providing & fixing of number plate with clamp, nut and bolts. 77 supply & fixing of barbed wire on the poles. 78 supply fixing and clamping of g.i pipe 150mm dia 02 mtr. height....

Military Engineer Services - Uttar Pradesh

33534756 preventive maintenance of street light including connected works under ge ( af ) bamrauli 1 excavation in trenches / pits in any type of soil ( soft / loose ) , n.exc. 1.5m wide and n.exc. 1.5m deep and getting out complete, all as specified & directed . 2 returning filling in with the earth obtained from item no 1here in before including spreading, leveling and well ramming in layers n.exc. 25cm thick complete all as specified & directed. 3 removal of surplus excavated material to a distance n.exc. 50 mtr and depositing where directed at a level n.exc. 1.5 mtr above starting point complete all as specified & directed 4 supply and laying sub class b bricks ( old size ) laid flat in trenches as cable covers complete all as specified and directed 5 supply and spreading clean and dry sand ( unwashed ) in trenches around the cable and in the cable ducts of ltpanels for cushioning all as specified & directed 6 site clearance in soft / loose soil and getting out complete all as specified and directed. 7 supply and lay in replacement of cable xlpe insulated screened pvc bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty ) 1100 volts grade with standard aluminium conductor of size 25 sqmm 3.5 core including taking down old u / s cable complete all as specified and directed. 8 all as oer item no.7 but of size 16 sqmm 4 core. 9 all as per item no. 7 of size 10 sqmm 4 core. 10 s & f in replacement of pvc insulated sheathed aluminium 2.5 sqmmtwin core cable, 1100 volt grade complete all as specified and directed. 11 ditto all as per item no 10 here in before but of size 4 sqmm twin core. 12 ditto all as per item no 10 here in beforebut of size 6 sqmm twin core. 13 ditto all as per item no 10 here in before but of size 10 sqmm twin core. 14 m&l for painting of 11 m steel polewith cross arms, clamp of any length and shape for ht overhead line / street light with two coat of aluminium paint including preparation of the existing surface including marking pole numbers in a 15 cm dia yellow circle & markingthree blue& two white bends width 30 cm by fluorescent paint, from bottom of pole to 1.5 mtr height, complete all as specified and directed. 15 m&l for painting of 9 m steel polewith cross arms, clamp of any length and shape for lt overhead line / street light with two coat of aluminium paint including preparation of the existing surface including marking pole numbers in a 15 cm dia yellow circle & markingthree blue& two white bends width 30 cm by fluorescent paint, from bottom of pole to 1.5 mtr height, complete all as specified and directed. 16 m&l for painting ofsteel pole hight up to 4 mtrwith clamp of any length and shapewith two coat of aluminium paint including preparation of the existing surface complete all as specified and directed. 17 s& f in replacement timer panel factory made cpri approved outdoor type 415 volts 3 phase 4 wire ac 50 hz cubical type weather & vermin proof 3.15 mm thick sheet crca sheet suitable size conopy roof extended on all four sides by not less than 10cm painting with powder coating including locking arrangement and mounted on wall / pole, frontopening with single shtter and one earth terminals suitable cable gland for all cbale incoming &out goining including testing complete all as specified and directed & directed by engineer in charge including the following accessories: ( i ) mccb 63 amp, 3 pol, 10 ka as incommer ( ii ) power connector 40 amp tp 3 phase 415 volts 01 no. ( iii ) digital timer 24 hours 01 no. ( iv ) auto / manual selector switch 01no. ( v ) ryb phase indicators for main supply. ( vi ) mcb 40 amp tpn 30 ka c seriese 03 no as outgoing. ( vii ) start / stop push button. ( viii ) internal wiring with pvc insulated copper conductor multistranded cable 10 volts grade is 694 marked of appropriate gauge including all cable copper lugs. 18 supply and laying in replacement of gi pipe “light grade” in trenches, under floors, roads, along poles for protection of cables, including sealing ends all asspecified & directed of following size : ( clamps to be measured and paid under appropriate item ) 19 ( a ) 40mm bore 20 ( b ) 50mm bore 21 taking down unserviceable street light fittings led / sodium / mercury vapour / metal halide / solar / high mast / post top lantern / torsio / down lighterof any wattage or size for repair / replacement of burn out / worn out / weak accessories and re fixing in position after repair / replacement of accessories and testing etc complete.note : 1. parts requierdfor replacement, shall be measured & paid separately under appropriate items. 22 supply only following parts for street lights: 23 electronic drive, 230 v, 50 hz, protection grade ip 66, with surge protection suitable for 100 / 90 watt street light and flood light fittings. 24 electronic drive, 230 v, 50 hz, protection grade ip 66, with surge protection suitable for 60 / 70 watt street light and flood light fittings. 25 electronic drive, 230 v, 50 hz, protection grade ip 66, with surge protection suitable for 45 / 50 watt street light and flood light fittings. 26 s&f in replacement led bulb 5 watt 27 s&f in replacement led bulb 7 watt 28 s&f in replacement led bulb 9 watt 29 s&f in repair wiring in street light pole from junction box to light fitting three core1.5 sq mmcopper conductorinsulatedwith standard copper conductor drawing through poles and lugs. 30 s & f insulation pvc tape roll of size 1.80 cm x 25 mtr 31 s&f in replacement of led street light fitting 45 watt, with surge protection 4kv inbuilt in driver and minimum 10 kv separate, ip66 having pressure dia cast aluminum housing with heat resistant toughened glass, individual led lenses complete making connection with suitable in size 3 core of wire and suitable for mounted on 40 / 50mm dia pole. ( i ) the driver should be potted ant vibration type, ip66 should be sustain 440 volt for 2 4 hrs ( ii ) lm 79 and lm 80 test report with 50000burning hrs led life from nabl lab shall be provided ( iii ) cri ( colour rendering index of fixture shall be greater then 70 ( iv ) cct ( colour correlated temperature ) of fixture shall be ± 300k ( v ) system lumen efficiency shall be > 100 lumen / watt complete all as specified and directed. 32 s&f in replacement of led street light fitting 60 watt, with surge protection 4kv inbuilt in driver and minimum 10 kv separate, ip66 having pressure dia cast aluminum housing with heat resistant toughened glass, individual led lenses complete making connection with suitable in size 3 core of wire and suitable for mounted on 40 / 50mm dia pole. ( i ) the driver should be potted ant vibration type, ip66 should be sustain 440 volt for 2 4 hrs ( ii ) lm 79 and lm 80 test report with 50000burning hrs led life from nabl lab shall be provided ( iii ) cri ( colour rendering index of fixture shall be greater then 70 ( iv ) cct ( colour correlated temperature ) of fixture shall be ± 300k ( v ) system lumen efficiency shall be > 100 lumen / watt complete all as specified and directed. 33 s & f in replacement of holder suitable for ptl / decorative fittings 34 s&f in replacement integral led aviation light comprising of aluminium housing with polycarbonate enclosureincluding provn of three core cable of copper conductor of size 2.5 sqmm 3 core of white coveringfor making connection, fixing the fitting on wall including all necessary fixing accessories complete all as directed. 35 m&l for attending and rectifying any type of street light, flood lights, perimeter lights fittings, high mast lights, gate light , post top lantern, garden lights, switches sockets, bulb, holders , pole box, power points , dbs , mcbs service connection by decarbonising neutrals , checking for any loose connections in the boardsall complaints by electrician and helper in north camp, tech area, happy home, 71 rmu, 820 su, begum bazar, 14 p&su, map, south camp, new project, veer path and other area as directed by engr in charge. note ( i ) the contractor will be responsible for safety, security as per mes standard. ( ii ) all tools and plants like plier, screw driver, tester, test lamp, clamp meter, bamboo ladder etc will be provided by contractor. ( iii ) each job contains minimum 5 complaints. ( iv ) each job ( minimum five complaints ) done by one electricin including helper. ( v ) complaint shall be attended round the clock without refusing as and when called for by engr in charge. 36 m & l for earthing complete with galvanized steel earth plate electrode60 cm x 60cm x 6.0mm thick buried directly in ground vertically to a depth not less than2.25 mtr below ground level with top edge of the earth plate not less less than 1.5 mtr below normal ground level and connectedto earth plate 32mm x 6mm thick by means of bolts, nuts etc surrounded by 15 cm thick packed layers of charcoal dust and common salt and protected by galvanized iron or steel pipe light grade 40mm bore and water pipe 20mm bore gi light grade with funel and connecting to test point including construction of chamber in cement concrete 1:3:6 type c 2 and rcc cover provn of test point and all as shown in electric plate no 3 of mes sch part i of 2009.including dismantling / taking out old earthing with all accessories complete. note: rcc pit cover shall be pre cast of rcc ( 1:2:4 ) type, b 1 80mm thick reinforced with xpm weighting not less than 4 kgs / sqm in lieu of ci cover. 37 m&l for cutting of tree branches touching / fallingon over head line upto 2 m distance from conductors including clearing the site complete.note : cutting of tree branches shall be done only at places / spans where thick / dense trees are existing around over head lines. 38 s&f in replacement of flexible led strip 25w, ip 65 ww uses high brightness , transparent , heat resistant with pvc covering duly visible in dark from far off distance fitted with suitable connectors for inter connection compl ete plug and socket arrangement suitable to be fitted on edges of buildings, pathways and outer periphery of boundary walls , maingates , hardstandings etc complete with clamping at suitabledistance to take the shape of required physical structure of warm whiteall as directed and specified. 39 m & l for painting of af color strip up to 1.5 mtr height on pcc / steel pole including junction box & marking of pole no by trained painter etc complete as specified and directed by engineer in charge. 40 supply and fixing in replacement of street light bracket ( with two set of clamp, nuts & bolts ) made out of 32 mm medium grade gi pipe bend to shape and with fixing arrangement duly welded all as directed, length of pipe should not be lessthan 1.2 mtrs complete all as directed. 41 s&f in replacement of led flood light fitting 150 watt, with surge protection 4kv inbuilt in driver and minimum 10 kv separate, ip66 having pressure dia cast aluminum housing with heat resistant toughened glass, individual led lenses complete making connection with suitable in size 3 core of wire and suitable for mounted on angle iron frame. ( i ) the driver should be potted ant vibration type, ip66 should be sustain 440 volt for 2 4 hrs ( ii ) lm 79 and lm 80 test report with 50000burning hrs led life from nabl lab shall be provided ( iii ) cri ( colour rendering index of fixture shall be greater then 70 ( iv ) cct ( colour correlated temperature ) of fixture shall be ± 300k ( v ) system lumen efficiency shall be > 100 lumen / watt complete all as specified and directed. 42 m&l for cutting of grass, roots touching / fallingon elect pole upto top of pole including clearing the site complete. note : cutting of grass, roots shall be done only at places / spans where all are existing around elect pole. 43 supply & fixing in replacement of contactor suitable for street light timer panel any type following size. 44 ( a ) mnx 32 45 ( b ) mnx 25 46 ( c ) mnx 50 47 ( d ) mnx 63 48 s&f in replacement of ledpost top lanterns 25w spherical shape polycarbonate diffuser & ip65 protection. led efficacy more then 100 lm / watt, 6500k, pf not less then 0.95 thd < 10 % suitable for mounting on 40 / 50 mm pole, necessary pre cast conector for connecting wire, complete. 49 supply & fixing in replacement of junction box [ frp ] of size 250 x 200 x 100 mm complete with bakelite connector100 apms capacity 4 way mcb sp 06 amps capacity with necessary fixing arrangements by providing ms clamps 2 nos made out of ms flat 25 x 5mm including nut bolts etc complete. 50 s&f in replacement of led bollards 8watt / 9watt in cylindrical shape with opal acrylic diffuser and ip 65 protection complete with all accessories including provn of three core cable of copper conductor of size 2.5 sqmm 3 core of white covering , for making connection including all necessary fixing accessories complete all as directed make : havells / philips / crompton / wipro. 51 s& f in replacement of digitel type timer switch, 415 volts 3 phase suitable for existing timer panel complete all as specified and directed by engineer in charge. 52 s& f in replacement of mcb tpn , 415 volts , 32 amps, c series, 10ka. make : legrand / l&t / schneider 53 s& f in replacement of mcb tpn , 415 volts , 63 amps, c series, 10ka.make : legrand / l&t / schneider 54 s& f in replacement of mcb spn, 240 volts, 5 to 32, amps c series, 10ka. make :legrand / l&t / schneider 55 s& f in replacement of mcb spn, 240 volts, 63, amps c series, 10ka. make :legrand / l&t / schneider 56 note : credit shown in credit schedule of tender document shall be considered by the tenderer while quoting the rates of various items. the same shall be recovered from various payment to contractor before handing over old material....

Purvanchal Vidyut Vitaran Nigam Limited - Uttar Pradesh

33488328 development of distribution infrastructure of package prayagraj 2 at kaushambi, fatehpur, and pratapgarh district of puvvnluttar pradeshunderrevamped reforms based and results linked, distribution sector scheme 1 conversion of existing lt lines on bare conductor to areal bunch xlpe cable 2 conversion of existing lt lines with bare conductor to ab xlpe cable using additional supports matching with length and type of existing support asper technical specifications, scope of works and approved drawings 3 supply of 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 4 galvanized stay set for lt line with anchor plate ( 200x200x6mm ) , 50x8mm stay clamp, 1 no. stay guy insulator, nut bolts, 1 nos turn buckles, 1.8 m long, 16 mm diameter solid gs stay rod & 7 / 3.15 mm dia gi stranded wire etc as required as per technical specification, approved drawings and scope of work. 5 conversion of existing lt lines using new earthing as per approved drawings, technical specifications and scope of work 6 supply of spike earthing made of 20mm x 2500 mm gi solid rod 7 supply of 8 swg gi wire for earthing and guarding 8 supply of following lt ab xlpe cable for conversion of existing lt bare conductor line with ab xlpe cable as required as per technical specification, approved drawings and scope of work: 9 supply of aerial bunchedxlpe cable 3 x 50 sqmm+1x35 sqmm. ( bare messenger wire ) +1x16 sqmm. 10 supply of aerial bunchedxlpe cable 3 x 70 sqmm.+1x50 sqmm. ( bare messenger wire ) +1x16 sqmm. 11 supply of aerial bunchedxlpe cable 3 x 95 sqmm.+1x70 sqmm. ( bare messenger wire ) + 1x16 sqmm. 12 supply of aerial bunchedxlpe cable 3 x 120 sqmm. + 1x95 sqmm. ( bare messenger wire ) +1x16 sqmm. 13 supply of pole mounted lt distribution box as per approved drawings, technical specifications and scope of work 14 supply of three phase smc distribution box with clamps 15 supply of single phase smc distribution box with clamps 16 supply of xlpe insulated al. cable for energisation of distribution box / kiosk as per approved drawings, technical specifications and scope of work 17 suppply of 2cx25 sqmm stranded unarmoured xlpe cable ( al conductor ) for chargingsingle phase db 18 suppply of 4cx35sqmm stranded unarmoured xlpe cable ( al conductor ) for chargingthreephase db 19 supply of stone pad ( 300x300x75 ) 20 supply of accessories for ab xlpe cable as per approved drawings, technical specifications and scope of work 21 stainless steel strap 22 hdg lt pole clamp with nut & bolt for laying abc 23 dead end clamp with i hook ( insulated ) 24 suspension clamp with i hook ( insulated ) 25 95 / 35 sqmm 70 / 25 sqmm pg clamps ( for line to line jumpering & energizing db neutral ) 26 120 / 50 sqmm 95 / 25 sqmm pg clamps ( for line to line jumpering & energizing db neutral ) 27 lt insulation piercing connector 120 50 sqmm 50 25 sqmm size ( for energizing distribution box ) 28 lt insulation piercing connector 120 50 sqmm 120 50 sqmm size ( for line to line jumpering ) 29 lt insulation piercing connector 16 25sqmmsize suitable for street light connection 30 pre insulated compression connectors size 16 sqmm suitable for ab xlpe cable 31 pre insulated compression connectors size 50 sqmm suitable for ab xlpe cable 32 pre insulated compression connectors size 70 sqmm suitable for ab xlpe cable 33 pre insulated compression connectors size 95 sqmm suitable for ab xlpe cable 34 pre insulated compression connectors size 120 sqmm suitable for ab xlpe cable 35 heat shrinkable type end cap for ab xlpe cable 36 supply of new 11 kv lines : feeder segregation ( agriculture feeder ) 37 supply of support for 11 kv overhead line as per technical specification, approved drawings and scope of work 38 supply of 8.5m / 180 kgs pcc poles ( pcc pole as per state practice ) 39 supply of 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 ( is 2713, pt i, ii, iii 1980 ) 40 supply for 3 phase 11 kv line using new pre fabricated hot dip galvanized steel items like v cross arm, top channel, top clamp, cross arm, bracket, clamps, cross bracings, bracings, strain plate, guarding channels, back clamp, ms angle, ms transformer base channel, ms flats pole extension channel with welded plate, anti climbing device clamp etc of given sizes for over head structures as per technical specification, approved drawings and scope of work. 41 supply of hot dip galvanized ms nuts, bolts with washers turn buckle for guarding as per technical specification, approved drawings and scope of work. 42 supply of pole accessories as per technical specification, approved drawing and scope of work 43 supply of 11 kv danger board 44 supply of stone pad 300x300x75 45 supply of barbed gi wire 12 swg 46 supply of stay set ( galvanized ) with 50x8 mm stay clamp, stay guy insulator ( 1 nos. ) , anchor plate ( 200x200x6 ) , nut bolts, 1 nos turn buckles, 1.8 m long, 16 mm diameter solid gs stay rod & 7 / 3.15 mm dia gi strandedwire complete as per technical specification, approved drawings and scope of work. 47 supply of insulator and hardware as per technical specification, approved drawings and scope of work. 48 supply of 11 kv45 kn polymer disc insulator along with suitable hardware fittings 49 supply of 11 kv 5 kn polymer pin insulators 50 supply of earthing arrangement as per technical specifications, approved drawings and scope of work. 51 supply of spike earthing 20mm x 2500 mmgi solid rod 52 supply of 8 swg gi wire for earthing and guarding 53 supply of 6 swg gi wire for earthing and guarding 54 supply of acsr conductors of following sizes with jointing sleeves, binding materials, pg clamps, bi metallic clamp, hardware etc for overhead line and jumpers as required as per technical specification, approved drawings and scope of work 55 supply of 6 / 2.59 + 1 / 2.59 mm ( 30 mm² al. area ) weasel 56 supply of 11 kv, 600a, 3 ph, 3 pin type, vertical mounting type, gang operated, ab switch along with support insulators, base channel down pipe, arcing horns etc. complete asper technical specifications, scope of works and approved drawings 57 supply of 11 kv lineunderground railway crossing ensuring statutory clearances as required as per technical specification, approved drawings and scope of work 58 supply for 11 kv lineunder ground railway crossing with 2 nos ( including one spare ) 3cx185 sqmm xlpe armored cable ( 0.3 km each ) using 150mm dia gi pipes ( grade a for underground laying and grade b for pole support ) , outdoor heat shrinkable cable jointing kit, 11 kv lightening arrestor station class 10ka ( 6 nos. ) , lugs, 4 nos gi 3 meters long pipe earthing, 6 swg gi wires, cable markers, bi metallick clamps and jumpering etc as required as per technical specifications, drawings and scope of the work. 59 supply of 11 lv line underground highway crossing ensuring statutory clearancesas required as per technical specification, approved drawings and scope of work 60 supply of 11 kv lineforunder ground highway crossing by 2 nos ( including one spare ) 3cx185 sqmm xlpe armored cable ( 0.3 km each ) using 160 mm hdpe pipe at road crossing and 150mm dia gi pipes ( gradeb for pole support ) , outdoor heat shrinkable cable jointing kits, 11 kv lightening arrestor station class 10ka ( 6 nos. ) , lugs, 4 nos gi 3 meters long pipe earthing, 6 swg gi wires, 7 / 20 gi wire, cable markers, bi metallick clamps and jumpering etc as required as per technical specifications, drawings and scope of the work. 61 supply of 12 kv 3ph indoor type switch gear and 11 kv xlpe cable as per technical specifications, approved drawings and scope of works: 62 supply of indoor type 12 kv 3 ph 1250 a vcb with control and protection system for out going feeder consisting ofct, a meter, volt meter, relays, energy meter ( tvm ) dlms compliant & accessories complete as per specifications for feeder breaker protection 63 11 kv 3x 185 sqmm xlpe armored power cable, aluminum stranded conductor, including their termination materials like indoor and outdoor termination kit, glands, lugs, tagging, cable path marker etc as required as per technical specifications, approved drawings and scope of the works. 64 supply for augmentation of lines 65 supply for augmentation of 33 kv line 66 supply for augmentation of 3 phase 33 kv line using additional supports matching with length and type of existing support asper technical specifications, scope of works and approved drawings 67 supply of 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 ( is 2713, pt i, ii, iii 1980 ) 68 supply new pre fabricated hot dip galvanized steel item, for augmentation of 33 kv line, like v cross arm, top channel, top clamp, cross arm, bracket, clamps, cross bracings, bracings, strain plate, guarding channels, back clamp, ms angle ( 65x65x6mm ) , ms flats ( 65x8mm ) anti climbing device clamp etc of given sizes for over head structures as per technical specification, approved drawings and scope of work. 69 supply of hot dip galvanized ms nuts, bolts with washers and turn buckle for guarding as per technical specification, approved drawings and scope of work. 70 supply of pole accessories as per technical specification, approved drawing and scope of work 71 supply of 33 kv danger board 72 supply of gi barbed wire 12 swg 73 supply for augmentation of 3 phase 33 kv line replacing existing conductor with following type of new acsr conductor including jointing sleeves, binding material, aluminum tape and helical preformed fittings etc as required as per technical specification, approved drawings and scope of work. 74 supply of 6 / 4.72 mm+7 / 1.57 mm ( 100 mm² al. area ) dog replacing existing racoon conductor 75 supply of 30 / 3.00 + 7 / 3.00 mm ( 200 mm² al. area ) panther replacing existing dog / racoon conductor 76 supply of 33 kv under ground cable as per technical specification, approved drawings and scope of work. 77 supply of 3cx300 sqmm 33 kv xlpe armored cable 78 supply of accessories for 33 kv3cx300 sqmm xlpe armored cable ( 2 nos including one spare ) like 160mm dia hdpe pipes for road crossing and 150 mm dia gi pipegrade b for pole support outdoor heat shrinkable cable jointing kits, lugs, cablepath markers, bi metallic clamps, and 7 / 20 gi wire as per technical specification, approved drawing and scope of work 79 supplyof new insulator and hardware for augmentation of33 kv line as per technical specification, approved drawings and scope of work 80 supply of 33 kv 70 kn polymer disc insulator along with suitable hardware fittings 81 supply of 33 kv 10 kn polymer pin insulators 82 supply of new earthing arrangement for augmentation of33 kv line as per technical specifications, approved drawings and scope of work. 83 8 swg gi coil 115 turns ( 1.85 kg ) 84 supply of new stay set ( galvanized ) for 33 kv line with 50x8 mm stay clamp, 2 nos. guy insulator, anchor plate ( 300x300x8mm ) , nut bolts, 1 no. turn buckles, 1.8 m long, 20 mm diameter solid gs stay rod & 7 / 4.00 mm dia gi strandedwire complete as per technical specification, approved drawings and scope of work. 85 supply of new gi wire for earthing and guarding for augmentation of33 kv line as per technical specification, approved drawings and scope of work. 86 supply of 6 swg gi wire 87 supply of 8 swg gi wire 88 supply of conductor accessories as per technical specification, approved drawing and scope of work 89 supply of pg clamp for dog to dog conductor 90 supply of pg clamp for panther to panther conductor 91 supply for augmentation of 11 kv lines 92 supply for augmentation of 3 phase 11 kv line using additional supports matching with length and type of existing support asper technical specifications, scope of works and approved drawings 93 supply of 8.5 meter long / 180 kg pcc poles ( pcc pole as per state practice ) 94 supply for augmentation of 3 phase 11 kv line using new pre fabricated hot dip galvanized steel items like v cross arm, top clamp, cross arm, bracket, clamps, cross bracings, bracings, strain plate, guarding channels, back clamp, ms angle, ms flats pole extension canal with welded plate, anti climbing device clamp etc of given sizes for over head structures as per technical specification, approved drawings and scope of work. 95 supply of hot dip galvanized ms nuts, bolts with washers and turn buckle for guarding as per technical specification, approved drawings and scope of work. 96 supply of pole accessories as per technical specification, approved drawing and scope of work 97 supply of 11 kv danger board 98 stone pad ( 300x300x75mm ) 99 supply of gi barbed wire 12 swg 100 supply for augmentation of 3 phase 11 kv line replacing existing conductor with following type of new acsr conductor including jointing sleeves, binding material and helicon formed fittings etc as required as per technical specification, approved drawings and scope of work. 101 supply of 6 / 2.59 + 1 / 2.59 mm ( 30 mm² al. area ) weasel by replacing existing weasel / squirrel conductor 102 supply of 6 / 3.35 + 1 / 3.35 mm ( 50 mm² al. area ) rabbit by replacing existing weasel / squirrel conductor 103 supply of 6 / 4.72 mm+7 / 1.57 mm ( 100 mm² al. area ) dog by replacing existing racoon / rabbit conductor 104 supply for augmentation of 3 phase 11 kv line using new insulator and hardware as per technical specification, approved drawings and scope of work 105 supply of 11 kv 45 kn polymer disc insulator along with suitable hardware fittings 106 supply of 11 kv 5 kn polymer pin insulators 107 supply for augmentation of 3 phase 11 kv line using new earthing arrangement as per technical specifications, approved drawings and scope of work. 108 supply of gi earthing spike made of 20x2500mm solid rod 109 supply for augmentation of 3 phase 11 kv line using new stay set ( galvanized ) with 50x8 mm stay clamp, guy insulator, anchor plate ( 200x200x6mm ) , nut bolts, 1 no turn buckles, 1.8 m long 16 mm diameter solid gi stay rod & 7 / 3.15 mm dia gi strandedwire complete as per technical specification, approved drawings and scope of work. 110 supply for augmentation of 3 phase 11 kv line using new gi wire for earthing and guarding as per technical specification, approved drawings and scope of work. 111 supply of 6 swg gi wire 112 supply of 8 swg gi wire 113 supply of conductor accessories as per technical specification, approved drawing and scope of work 114 supply of pg clamp for weasel to weasel conductor 115 supply of pg clamp for dog to dog conductor 116 supply of pg clamp for rabbit to rabbit conductor 117 installation of dt capacitor 118 supply of dt capacitor with fitting as per technical specification, approved drawing and scope of work 119 supply of lt shunt capacitor 440 volt 10 kvar 3phase 50hz ip65 120 supply of lt shunt capacitor 440 volt 16 kvar 3phase 50hz ip65 121 supply of lt shunt capacitor 440 volt 25 kvar 3phase 50hz ip65 122 supply of lt shunt capacitor 440 volt 40 kvar 3phase 50hz ip65 123 erection part 124 erection for conversion of existing lt lines on bare conductor to aerial bunch xlpe cable 125 excavation of additional pole pit ( of depth 1 / 6th of pole length ) in normal soil of following pole as per scope of work, approved drawings and specifications: 126 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 127 erection of following types of poles for lt overhead line with stone pad, pole numbering by paint with cement concrete foundation using 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) etc as per scope of work, approved drawings and specifications: 128 erection of 8.5 m / 180 kgs pcc poles with base stone pad as required ( state practices of pcc pole and stone pad to be used ) 129 excavation of lt stay pit in following type of soils, as per scope of work, approved drawings and specifications: 130 normal soil 131 erection of complete stay set with gi stay wire ( 7x3.15 mm dia ) , binding of stay wire, by providing guy stay insulator and 0.2 cmt concreting 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) as per technical specifications, approved drawings and scope of works. 132 removal of existing lt bare line conductor & fixtures, depositing to stores of employer and erection, testing & commissioning of new areal bunched xlpe cable, fixing tension clamps for dead end, suspension clamps, clamps for neutral, piercing connectors type i & type ii, pre insulated compression connectors, 16 mm dia ms nuts & bolts, pole clamps, stainless steel strap, single and three phase pole mounted distribution board, energisation of distribution box through 2cx25 sqmm and 4cx35 sq.mm xlpe cable fixing end cap etc. as required as per technical specification, approved drawings and scope of work: 133 erection of aerial bunched xlpe cable3 x 50 sqmm +1x35 sqmm ( bare messenger cum neutral ) +1x16 sqmm 134 erection of aerial bunched xlpe cable 3 x 70 sqmm +1x50 sqmm ( bare messenger cum neutral ) +1x16 sqmm 135 erection of aerial bunched xlpe cable 3 x 95 sqmm +1x70 sqmm ( bare messenger cum neutral ) + 1x16 sqmm 136 erection of aerial bunched xlpe cable 3 x 120 sqmm+ 1x95 sqmm ( bare messenger cum neutral ) +1x16 sqmm 137 erection, testing & commissioning of earthing by inserting gi earthing spike made of 20mm solid rod as per approved drawings, scope of work and technical specifications 138 erection of 8 swg gi wire for earthing by providing gi nut, bolts & washers, turn buckle etc as per approved drawings, scope of work and technical specifications 139 erection, testing and commissioning of new 11 kv lines: feeder segregation ( agriculture feeder ) 140 survey, route alignment & pole spotting, preparation of survey report and uploading in the web portal after approval of project manager 141 excavation of pole pit ( of depth 1 / 6th of pole length ) in normal soil for following type pole as per scope of work, approved drawings and specifications: 142 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 143 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 ( is 2713, pt i, ii, iii 1980 ) 144 erection of following types of poles for 11 kv overhead line by installing danger plate, anti climbing devices ( barbed wire ) , painting by red oxide & aluminum paint to stp poles including paint, numberingof poleby paint including cement concrete foundation using cement concreting foundation 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) etc as per scope of work, approved drawings and specifications: 145 erection of 8.5 m / 180 kgs pcc poles with base pad including cement concreting, ( state practices of pcc pole, stone to be used ) 146 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 ( is 2713, pt i, ii, iii 1980 ) cement concreting 0.5 cmt + 0.014 cmt ( muffing ) 147 erection, testing & commissioning of pre fabricated hdg steel items like v cross arm, top channel, top clamp, cross arm, bracket, clamps, cross bracings, bracings, strain plate, guarding channels, back clamp, etc made of ms channels, ms angle, ms flats of given sizes for over head structures and ms nuts, bolts & washersas per technical specification, approved drawings and scope of work. 148 earthing arrangement as per technical specifications, approved drawings and scope of work. 149 erection, testing & commissioning of spike earthing 20mm x 2500mm solid rod 150 excavation of stay pit in following type of soils, as per scope of work, approved drawings and specifications: 151 normal soil 152 erection of complete stay set with gi stay wire ( 7x3.15 mm dia ) , binding of stay wire, by providing guy stay insulator ( 1 nos. ) and 0.2 cmt concreting 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) as per technical specifications, approved drawings and scope of works. 153 erection, testing and commissioning of 11 kv insulator including their hardware fittings as per technical specification, approved drawings and scope of work. 154 erection of 5 kn 11 kv polymer pin insulator 155 erection of 45 kn 11 kv polymer disc insulator with strain hardware 156 laying out, tensioning, binding of conductor and tightening of stays and stringing, testing and commissioning of acsrconductor of following sizes including jointing sleeves, helical formed fittings, jumpering and by providing & erecting pg clamps etc as required as per approved drawings, scope of work and technical specifications 157 stringing of 6 / 2.59 + 1 / 2.59 mm ( 30 mm² al. area ) weasel 158 erection, testing and commissioning of vertical type 11 kvab switch along with support insulators, base channel, down pipe, arcing horns etc. complete asper technical specifications, scope of works and approved drawings 159 erection, testing & commissioning of 11 kv line for under ground railway crossing by2 nos ( including one spare ) 3cx185 sqmm xlpe armored cable ( 0.3 km each ) , using 150mm dia gi pipes, outdoor heat shrinkable cable jointing kits, lugs, 4 nosgi 3 meters long earthing pipe, 6 swg gi wires, cable markers, clamps, jumpering and 11 kv station type lightening arrestors ( 6 nos. ) , etc as required as per technical specifications, approved drawings and scope of he work. 160 erection, testing & commissioning of 11 kv line for under ground highway crossing by2 nos ( including one spare ) 3cx185 sqmm xlpe armored cable ( 0.3 km each ) , using 160 mm hdpe pipe at road crossing, 150mm dia gi pipes for cable support, outdoor heat shrinkable cable jointing kits, lugs, 4 nosgi 3 meters long earthing pipe, 6 swg gi wires, 7 / 20 gi wire, cable markers, clamps, jumpering, 11 kv station type lightening arrestors ( 6 nos. ) , etc as required as per technical specifications, approved drawings and scope of he work. 161 erection of 12 kv, 1250 a, 25ka for 3 seconds, 3 ph, indoor typevacuum circuit breaker with adopter panel for out going feeder by leveling, alignment and welding on existing cable trench in control room. testing & commissioning of indoor vcb panel including 3 nos indoor type current transformer, a meter, volt meter, relay & accessories protection as per approved drawings, technical specifications and scope of the work.: 162 providing and fixing of sign board includingmaterial and its fabrication , painting , writing , logo and scheme name etc as per rdss guidelines and t.s 163 laying, erection, termination using indoor & outdoor termination kit, 11kv 3x 185 sqmm xlpearmored power cablesas per technical specifications, approved drawings and scope of works. : 164 erection, testing & commissioning of new gi wire for earthing and guarding as per technical specification, approved drawings and scope of work. 165 erection of 6 swg gi wire 166 erection of 8 swg gi wire 167 extension of control room of 33 / 11 kv substation to accommodate vcb for new 11 kv feeders as per technical specification, approved drawing and scope of work. 168 design, engineering construction of control room building extension 300 sq feet including cost ofall materials, t&p and labour, etc. as per technical specification and approved drawing as per direction of employer 169 shifting of following distribution transformer along with fixture including dismantling , shifting and erection from one location to another location as per approved survey. 170 single phase transformer 171 three phase transformer 172 erection for augmentation of lines 173 erection for augmentation of 33 kv line 174 excavation of additional pole pit ( of depth 1 / 6th of pole length ) in normal soil as per scope of work, approved drawings and specifications: 175 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 ( is 2713, pt i, ii, iii 1980 ) 176 erection of following types of additional poles matching with existing line supports by installing danger plate, anti climbing devices ( barbed wire ) , painting with red oxide & aluminum paint including paint, pole numbering including cement concrete foundation using 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) etc as per scope of work, approved drawings and specifications: 177 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 ( is 2713, pt i, ii, iii 1980 ) cement concreting 0.5 cmt + 0.014 cmt ( muffing ) 178 excavation of stay pit for 33 kv stay in following type of soils, as per scope of work, approved drawings and specifications: 179 normal soil 180 erection of complete stay set with gi stay wire ( 7x4.00 mm dia ) , binding of stay wire, by providing guy stay insulator and 0.3 cmt concreting 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) as per technical specifications, approved drawings and scope of works. 181 erection, testing and commissioning of 33 kv insulator including their hardware fittings as per technical specification, approved drawings and scope of work. 182 erection of 33 kv 10 kn pin insulator with gi pin 183 erection of 33 kv 70 kn disc insulator with strain hardware ( set of 3, 11 kv disc insulators ) 184 erection, testing & commissioning of new pre fabricated hdg steel items like v cross arm, top clamp, cross arm, bracket, clamps, cross bracings, bracings, strain plate, guarding channels, back clamp, etc made of ms channels, ms angle, ms flats of given sizes for over head structures as per technical specification, approved drawings and scope of work. 185 dismantling of existing overhead line conductor and fittings, depositing the dismantled material to employers store and laying out & stringing of new acsr conductor of following sizes by providing jointing sleeves, binding wire & tape & helical formed fittings etc as required as per technical specification, approved drawings and scope of work. 186 stringing of 6 / 4.72 mm+7 / 1.57 mm ( 100 mm² al. area ) dog replacing existing racoon conductor 187 stringing of 30 / 3.00 + 7 / 3.00 mm ( 200 mm² al. area ) panther replacing existing dog / racoon conductor 188 erection, testing & commissioning of 33 kvunder ground cable by2 nos ( including one spare ) 3cx300 sqmm xlpe armored cable, using 160 mm hdpe pipe at road crossing, 150mm dia gi pipes for cable support, outdoor heat shrinkable cable jointing kits, lugs, cable markers, clamps, jumpering, etc as required as per technical specifications, approved drawings and scope of he work. 189 erection for augmentation of 3 phase 33 kv line using new insulator and hardware as per technical specification, approved drawings and scope of work 190 erection of 33 kv 70 kn polymer disc insulator along with suitable hardware fittings 191 erection of 33 kv 10 kn polymer pin insulators 192 erection, testing & commissioning of earthing as per technical specifications, approved drawings and scope of work. 193 8 swg gi coil 115 turns ( 1.85 kg ) 194 erection, testing & commissioning of new gi wire for earthing and guarding as per technical specification, approved drawings and scope of work. 195 erection of 6 swg gi wire 196 erection of 8 swg gi wire 197 erection for augmentation of 11 kv lines 198 excavation of additional pole pit ( of depth 1 / 6th of pole length ) in normal soil as per scope of work, approved drawings and specifications: 199 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 200 erection of following types of poles for 11 kv overhead line by installing danger plate, anti climbing devices ( barbed wire ) , pole numbering including cement concrete foundation using 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) etc as per scope of work, approved drawings and specifications: 201 erection of 8.5 m / 180 kgs pcc poles withbase stone pad ( state practices of pcc pole and base plate / stone to be used ) 202 excavation of stay pit in following type of soils, as per scope of work, approved drawings and specifications: 203 normal soil 204 erection of complete stay set with gi stay wire ( 7x3.15 mm dia ) , binding of stay wire, by providing guy stay insulator and 0.2 cmt concreting 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) as per technical specifications, approved drawings and scope of works. 205 erection, testing and commissioning of 11 kv insulator including their hardware fittings as per technical specification, approved drawings and scope of work. 206 erection of 11 kv pin insulator with gi pin 207 erection of 11 kv disc insulator with strain hardware 208 dismantling of existing overhead line conductor & fittings and depositing to employers store, laying out, tensioning, binding of new conductor and tightening of stays and stringing, testing and commissioning of acsrconductor of following sizes including jointing sleeves, helical formed fittings, jumpering and by providing & erecting pg clamps etc as required as per approved drawings, scope of work and technical specifications 209 stringing of 6 / 2.59 + 1 / 2.59 mm ( 30 mm² al. area ) weasel by replacing existing weasel / squirrel conductor 210 stringing of 6 / 3.35 + 1 / 3.35 mm ( 50 mm² al. area ) rabbit by replacing existing weasel / squirrel conductor 211 stringing of 6 / 4.72 mm+7 / 1.57 mm ( 100 mm² al. area ) dog by replacing existing racoon / rabbit conductor 212 erection, testing & commissioning of pre fabricated hdg steel items like v cross arm, top channel, top clamp, cross arm, bracket, clamps, cross bracings, bracings, strain plate, guarding channels, back clamp, etc made of ms channels, ms angle, ms flats of given sizes for over head structures and hdg ms nuts, bolts & washers as per technical specification, approved drawings and scope of work. 213 erection, testing and commissioning of 11 kv insulator including their hardware fittings as per technical specification, approved drawings and scope of work. 214 erection of 5 kn 11 kv polymer pin insulator 215 erection of 45 kn 11 kv polymer disc insulator with strain hardware 216 earthingand guarding arrangement as per technical specifications, approved drawings and scope of work. 217 erection, testing & commissioning of spike earthing 20mm solid rod 218 erection of 8 swg gi wire for earthing and guarding 219 erection of 6 swg gi wire for earthing and guarding 220 erection of dt capacitor 221 erection, testing & commissioning offollowing 440 volt lt shunt capacitor including mounting structure and accessories as required as per technical specifications, approved drawings and scope of work. 222 erection of lt shunt capacitor 440 volt 10 kvar 3phase 50hz ip65 223 erection of lt shunt capacitor 440 volt 16 kvar 3phase 50hz ip65 224 erection of lt shunt capacitor 440 volt 25 kvar 3phase 50hz ip65 225 erection of lt shunt capacitor 440 volt 40 kvar 3phase 50hz ip65 226 discount offered in % 227 words final quoted price after discount...

Purvanchal Vidyut Vitaran Nigam Limited - Uttar Pradesh

33488283 development of distribution infrastructure of packageprayagraj 1 at prayagraj district of puvvnluttar pradeshunderrevamped reforms based and results linked, distribution sector scheme 1 supply of consumer service cable 2 supply of armored service cable for consumer service connection with accessories as per technical specifications, scope of works and approved drawings 3 supply of single phase armored al cable size 2cx 6 sq mm 4 supply of three phase armored al cable size 4cx 16 sq mm 5 supply of 10 swg gi wire 6 supply of 8 swg gi wire 7 supply of gi pipe / m.s angle along with nails / clamps / proper binding e.t.c. as per rec std. 8 conversion of existing lt lines on bare conductor to areal bunch xlpe cable 9 conversion of existing lt lines with bare conductor to ab xlpe cable using additional supports matching with length and type of existing support asper technical specifications, scope of works and approved drawings 10 supply of 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 11 galvanized stay set for lt line with anchor plate ( 200x200x6mm ) , 50x8mm stay clamp, 1 no. stay guy insulator, nut bolts, 1 no. turn buckles, 1.8 m long, 16 mm diameter solid gs stay rod & 7 / 3.15 mm dia gi stranded wire etc as required as per technical specification, approved drawings and scope of work. 12 conversion of existing lt lines using new earthing as per approved drawings, technical specifications and scope of work 13 supply of spike earthing made of 20mm x 2500 mm gi solid rod 14 supply of 8 swg gi wire for earthing and guarding 15 supply of following lt ab xlpe cable for conversion of existing lt bare conductor line with ab xlpe cable as required as per technical specification, approved drawings and scope of work: 16 supply of aerial bunchedxlpe cable 3 x 50 sqmm+1x35 sqmm. ( bare messenger wire ) +1x16 sqmm. 17 supply of aerial bunchedxlpe cable 3 x 70 sqmm.+1x50 sqmm. ( bare messenger wire ) +1x16 sqmm. 18 supply of aerial bunchedxlpe cable 3 x 95 sqmm.+1x70 sqmm. ( bare messenger wire ) + 1x16 sqmm. 19 supply of aerial bunchedxlpe cable 3 x 120 sqmm. + 1x95 sqmm. ( bare messenger wire ) +1x16 sqmm. 20 supply of pole mounted lt distribution box as per approved drawings, technical specifications and scope of work 21 supply of three phase smc distribution box with clamps 22 supply of single phase smc distribution box with clamps 23 supply of xlpe insulated al. cable for energisation of distribution box / kiosk as per approved drawings, technical specifications and scope of work 24 suppply of 2cx25 sqmm stranded unarmoured cable ( al conductor ) for chargingsingle phase db 25 suppply of 4cx35sqmm stranded unarmoured cable ( al conductor ) for chargingthreephase db 26 supply of stone pad ( 300x300x75 ) 27 supply of accessories for ab xlpe cable as per approved drawings, technical specifications and scope of work 28 stainless steel strap 29 hdg lt pole clamp with nut & bolt for laying abc 30 dead end clamp with i hook ( insulated ) 31 suspension clamp with i hook ( insulated ) 32 95 / 35 sqmm 70 / 25 sqmm pg clamps ( for line to line jumpering & energizing db neutral ) 33 120 / 50 sqmm 95 / 25 sqmm pg clamps ( for line to line jumpering & energizing db neutral ) 34 lt insulation piercing connector 120 50 sqmm 50 25 sqmm size ( for energizing distribution box ) 35 lt insulation piercing connector 120 50 sqmm 120 50 sqmm size ( for line to line jumpering ) 36 lt insulation piercing connector 16 25sqmmsize suitable for street light connection 37 pre insulated compression connectors size 16 sqmm suitable for ab xlpe cable 38 pre insulated compression connectors size 50 sqmm suitable for ab xlpe cable 39 pre insulated compression connectors size 70 sqmm suitable for ab xlpe cable 40 pre insulated compression connectors size 95 sqmm suitable for ab xlpe cable 41 pre insulated compression connectors size 120 sqmm suitable for ab xlpe cable 42 heat shrinkable type end cap for ab xlpe cable 43 supply of new 11 kv lines : feeder segregation ( agriculture feeder ) 44 supply of support for 11 kv overhead line as per technical specification, approved drawings and scope of work 45 supply of 8.5m / 180 kgs pcc poles ( pcc pole as per state practice ) 46 supply of 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 ( is 2713, pt i, ii, iii 1980 ) 47 supply for 3 phase 11 kv line using new pre fabricated hot dip galvanized steel items like v cross arm, top channel, top clamp, cross arm, bracket, clamps, cross bracings, bracings, strain plate, guarding channels, back clamp, ms angle, ms transformer base channel, ms flats pole extension channel with welded plate, anti climbing device clamp etc of given sizes for over head structures as per technical specification, approved drawings and scope of work. 48 supply of hot dip galvanized ms nuts, bolts with washers and turn buckle for guarding as per technical specification, approved drawings and scope of work. 49 supply of pole accessories as per technical specification, approved drawing and scope of work 50 supply of 11 kv danger board 51 supply of stone pad 300x300x75 52 supply of barbed gi wire 12 swg 53 supply of stay set ( galvanized ) with 50x8 mm stay clamp, stay guy insulator ( 1 nos. ) , anchor plate ( 200x200x6 ) , nut bolts, 1 nos turn buckles, 1.8 m long, 16 mm diameter solid gs stay rod & 7 / 3.15 mm dia gi strandedwire complete as per technical specification, approved drawings and scope of work. 54 supply of insulator and hardware as per technical specification, approved drawings and scope of work. 55 supply of 11 kv45 kn polymer disc insulator along with suitable hardware fittings 56 supply of 11 kv 5 kn polymer with pin insulators 57 supply of earthing arrangement as per technical specifications, approved drawings and scope of work. 58 supply of spike earthing 20mm x 2500 mm gi solidrod 59 supply of 8 swg gi wire for earthing and guarding 60 supply of 6 swg gi wire for earthing and guarding 61 supply of acsr conductors of following sizes with jointing sleeves, binding materials, pg clamps, bi metallic clamp, hardware etc for overhead line and jumpers as required as per technical specification, approved drawings and scope of work 62 supply of 6 / 2.59 + 1 / 2.59 mm ( 30 mm² al. area ) weasel 63 supply of 11 kv, 600a, 3 ph, 3 pin type, vertical mounting type, gang operated, ab switch along with support insulators, base channel down pipe, arcing horns etc. complete asper technical specifications, scope of works and approved drawings 64 supply of 11 kv lineunderground railway crossing ensuring statutory clearances as required as per technical specification, approved drawings and scope of work 65 supply for 11 kv lineunder ground railway crossing with 2 nos ( including one spare ) 3cx185 sqmm xlpe armored cable ( 0.3 km each ) using 150mm dia gi pipes ( grade a for underground laying and grade b for pole support ) , outdoor heat shrinkable cable jointing kit, 11 kv lightening arrestor station class 10ka ( 6 nos. ) , lugs, 4 nos gi 3 meters long pipe earthing, 6 swg gi wires, cable markers, bi metallick clamps and jumpering etc as required as per technical specifications, drawings and scope of the work. 66 supply of 11 lv line underground highway crossing ensuring statutory clearancesas required as per technical specification, approved drawings and scope of work 67 supply of 11 kv lineforunder ground highway crossing by 2 nos ( including one spare ) 3cx185 sqmm xlpe armored cable ( 0.3 km each ) using 160 mm hdpe pipe at road crossing and 150mm dia gi pipes ( gradeb for pole support ) , outdoor heat shrinkable cable jointing kits, 11 kv lightening arrestor station class 10ka ( 6 nos. ) , lugs, 4 nos gi 3 meters long pipe earthing, 6 swg gi wires, 7 / 20 gi wire, cable markers, bi metallick clamps and jumpering etc as required as per technical specifications, drawings and scope of the work. 68 supply of 12 kv 3ph indoor type switch gear and 11 kv xlpe cable as per technical specifications, approved drawings and scope of works: 69 supply of indoor type 12 kv 3 ph 1250 a vcb with control and protection system for out going feeder consisting ofct, a meter, volt meter, relays, energy meter ( tvm ) dlms compliant & accessories complete as per specifications for feeder breaker 70 11 kv 3x 185 sqmm xlpe armored power cable, aluminum stranded conductor, including their termination materials like indoor and outdoor termination kit, glands, lugs, tagging, cable path marker etc as required as per technical specifications, approved drawings and scope of the works. 71 supply for augmentation of lines 72 supply for augmentation of 33 kv line 73 supply for augmentation of 3 phase 33 kv line using additional supports matching with length and type of existing support asper technical specifications, scope of works and approved drawings 74 supply of 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 ( is 2713, pt i, ii, iii 1980 ) 75 supply new pre fabricated hot dip galvanized steel item, for augmentation of 33 kv line, like v cross arm, top channel, top clamp, cross arm, bracket, clamps, cross bracings, bracings, strain plate, guarding channels, back clamp, ms angle ( 65x65x6mm ) , ms flats ( 65x8mm ) anti climbing device clamp etc of given sizes for over head structures as per technical specification, approved drawings and scope of work. 76 supply of hot dip galvanized ms nuts, bolts with washers and turn buckle for guarding as per technical specification, approved drawings and scope of work. 77 supply of pole accessories as per technical specification, approved drawing and scope of work 78 supply of 33 kv danger board 79 supply of gi barbed wire 12 swg 80 supply for augmentation of 3 phase 33 kv line replacing existing conductor with following type of new acsr conductor including jointing sleeves, binding material, aluminum tape and helical preformed fittings etc as required as per technical specification, approved drawings and scope of work. 81 supply of 6 / 4.72 mm+7 / 1.57 mm ( 100 mm² al. area ) dog replacing existing racoon conductor 82 supply of 30 / 3.00 + 7 / 3.00 mm ( 200 mm² al. area ) panther replacing existing dog / racoon conductor 83 supply of 33 kv under ground cable as per technical specification, approved drawings and scope of work. 84 supply of 3cx300 sqmm 33 kv xlpe armored cable 85 supply of 33 kv3cx300 sqmm xlpe armored cable ( 2 nos including one spare ) accessories like 160mm dia hdpe pipes for road crossing and 150 mm dia gi pipegrade b for pole support outdoor heat shrinkable cable jointing kits, lugs, cablepath markers, bi metallic clamps, 7 / 20 gi wire as per technical specification, approved drawing and scope of work 86 supplyof new insulator and hardware for augmentation of33 kv line as per technical specification, approved drawings and scope of work 87 supply of 33 kv 70 kn polymer disc insulator along with suitable hardware fittings 88 supply of 33 kv 10 kn polymer pin insulators 89 supply of new earthing arrangement for augmentation of33 kv line as per technical specifications, approved drawings and scope of work. 90 8 swg gi coil 115 turns ( 1.85 kg ) 91 supply of new stay set ( galvanized ) for 33 kv line with 50x8 mm stay clamp, 2 nos. guy insulator, anchor plate ( 300x300x8mm ) , nut bolts, 1 no. turn buckles, 1.8 m long, 20 mm diameter solid gs stay rod & 7 / 4.00 mm dia gi strandedwire complete as per technical specification, approved drawings and scope of work. 92 supply of new gi wire for earthing and guarding for augmentation of33 kv line as per technical specification, approved drawings and scope of work. 93 supply of 6 swg gi wire 94 supply of 8 swg gi wire 95 supply of conductor accessories as per technical specification, approved drawing and scope of work 96 supply of pg clamp for dog to dog conductor 97 supply of pg clamp for panther to panther conductor 98 supply for augmentation of 11 kv lines 99 supply for augmentation of 3 phase 11 kv line using additional supports matching with length and type of existing support asper technical specifications, scope of works and approved drawings 100 supply of 8.5 meter long / 180 kg pcc poles ( pcc pole as per state practice ) 101 supply for augmentation of 3 phase 11 kv line using new pre fabricated hot dip galvanized steel items like v cross arm, top channel, top clamp, cross arm, bracket, clamps, cross bracings, bracings, strain plate, guarding channels, back clamp, ms angle, ms flats pole extension canal with welded plate, anti climbing device clamp etc of given sizes for over head structures as per technical specification, approved drawings and scope of work. 102 supply of hot dip galvanized ms nuts, bolts with washers and turn buckle for guarding as per technical specification, approved drawings and scope of work. 103 supply of pole accessories as per technical specification, approved drawing and scope of work 104 supply of 11 kv danger board 105 stone pad ( 300x300x75mm ) 106 supply of gi barbed wire 12 swg 107 supply for augmentation of 3 phase 11 kv line replacing existing conductor with following type of new acsr conductor including jointing sleeves, binding material and helicon formed fittings etc as required as per technical specification, approved drawings and scope of work. 108 supply of 6 / 2.59 + 1 / 2.59 mm ( 30 mm² al. area ) weasel by replacing existing weasel / squirrel conductor 109 supply of 6 / 3.35 + 1 / 3.35 mm ( 50 mm² al. area ) rabbit by replacing existing weasel / squirrel conductor 110 supply of 6 / 4.72 mm+7 / 1.57 mm ( 100 mm² al. area ) dog by replacing existing racoon / rabbit conductor 111 supply for augmentation of 3 phase 11 kv line using new insulator and hardware as per technical specification, approved drawings and scope of work 112 supply of 11 kv 45 kn polymer disc insulator along with suitable hardware fittings 113 supply of 11 kv 5 kn polymer pin insulators 114 supply for augmentation of 3 phase 11 kv line using new earthing arrangement as per technical specifications, approved drawings and scope of work. 115 supply of gi earthing spike made of 20x2500mmsolid rod 116 supply for augmentation of 3 phase 11 kv line using new stay set ( galvanized ) with 50x8 mm stay clamp, 1 no. guy insulator, anchor plate ( 200x200x6mm ) , nut bolts, 1no. turn buckles, 1.8 m long 16 mm diameter solid gi stay rod & 7 / 3.15 mm dia gi strandedwire complete as per technical specification, approved drawings and scope of work. 117 supply for augmentation of 3 phase 11 kv line using new gi wire for earthing and guarding as per technical specification, approved drawings and scope of work. 118 supply of 6 swg gi wire 119 supply of 8 swg gi wire 120 supply of conductor accessories as per technical specification, approved drawing and scope of work 121 supply of pg clamp for weasel to weasel conductor 122 supply of pg clamp for dog to dog conductor 123 supply of pg clamp for rabbit to rabbit conductor 124 installation of dt capacitor 125 supply of dt capacitor with fitting as per technical specification, approved drawing and scope of work 126 supply of lt shunt capacitor 440 volt 10 kvar 3phase 50hz ip65 127 supply of lt shunt capacitor 440 volt 16 kvar 3phase 50hz ip65 128 supply of lt shunt capacitor 440 volt 25 kvar 3phase 50hz ip65 129 supply of lt shunt capacitor 440 volt 40 kvar 3phase 50hz ip65 130 supply of lt shunt capacitor 440 volt 63 kvar 3phase 50hz ip65 131 supply of lt shunt capacitor 440 volt 100 kvar 3phase 50hz ip65 132 erection part 133 installation of consumer service cable 134 installation of armored consumer service cable with accessories including dismantling of existing service cable as per technical specifications, scope of works and approved drawings 135 installation of single phase armored al cable size 2cx 6 sq mm 136 installation of three phase armored al cable size 4cx 16 sq mm 137 gi wire 8 swg 138 gi wire 10 swg 139 installation of gi pipe / m.s angle along with nails / clamps / proper binding e.t.c. as per r.e.c std. 140 erection for conversion of existing lt lines on bare conductor to aerial bunch xlpe cable 141 excavation of additional pole pit ( of depth 1 / 6th of pole length ) in normal soil of following pole as per scope of work, approved drawings and specifications: 142 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 143 erection of following types of poles for lt overhead line with stone pad, pole numbering by paint with cement concrete foundation using 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) etc as per scope of work, approved drawings and specifications: 144 erection of 8.5 m / 180 kgs pcc poles with base stone pad as required ( state practices of pcc pole and stone pad to be used ) 145 excavation of lt stay pit in following type of soils, as per scope of work, approved drawings and specifications: 146 normal soil 147 erection of complete stay set with gi stay wire ( 7x3.15 mm dia ) , binding of stay wire, by providing guy stay insulator ( 1 no. ) and 0.2 cmt concreting 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) as per technical specifications, approved drawings and scope of works. 148 removal of existing lt bare line conductor & fixtures, depositing to stores of employer and erection, testing & commissioning of new areal bunched xlpe cable, fixing tension clamps for dead end, suspension clamps, clamps for neutral, piercing connectors type i & type ii, pre insulated compression connectors, 16 mm dia ms nuts & bolts, pole clamps, stainless steel strap, single and three phase pole mounted distribution board, energisation of distribution box through 2cx25 sqmm and 4cx35 sq.mm xlpe cable fixing end cap etc. as required as per technical specification, approved drawings and scope of work: 149 erection of aerial bunched xlpe cable3 x 50 sqmm +1x35 sqmm ( bare messenger cum neutral ) +1x16 sqmm 150 erection of aerial bunched xlpe cable 3 x 70 sqmm +1x50 sqmm ( bare messenger cum neutral ) +1x16 sqmm 151 erection of aerial bunched xlpe cable 3 x 95 sqmm +1x70 sqmm ( bare messenger cum neutral ) + 1x16 sqmm 152 erection of aerial bunched xlpe cable 3 x 120 sqmm+ 1x95 sqmm ( bare messenger cum neutral ) +1x16 sqmm 153 erection, testing & commissioning of earthing by inserting gi earthing spike made of 20mm solid rod as per approved drawings, scope of work and technical specifications 154 erection of 8 swg gi wire for earthing by providing gi nut, bolts & washers, turn buckle etc as per approved drawings, scope of work and technical specifications 155 erection, testing and commissioning of new 11 kv lines: feeder segregation ( agriculture feeder ) 156 survey, route alignment & pole spotting, preparation of survey report and uploading in the web portal after approval of project manager 157 excavation of pole pit ( of depth 1 / 6th of pole length ) in normal soil for following type pole as per scope of work, approved drawings and specifications: 158 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 159 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 ( is 2713, pt i, ii, iii 1980 ) 160 erection of following types of poles for 11 kv overhead line by installing danger plate, anti climbing devices ( barbed wire ) , painting with red oxide & aluminum paint to stp poles including paint, numberingof poleby paint including cement concrete foundation using cement concreting foundation 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) etc as per scope of work, approved drawings and specifications: 161 erection of 8.5 m / 180 kgs pcc poles with base pad including cement concreting, ( state practices of pcc pole, stone to be used ) 162 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 ( is 2713, pt i, ii, iii 1980 ) cement concreting 0.5 cmt + 0.014 cmt ( muffing ) 163 erection, testing & commissioning of pre fabricated hdg steel items like v cross arm, top channel, top clamp, cross arm, bracket, clamps, cross bracings, bracings, strain plate, guarding channels, back clamp, etc made of ms channels, ms angle, ms flats of given sizes for over head structures and ms nuts, bolts & washersas per technical specification, approved drawings and scope of work. 164 earthing arrangement as per technical specifications, approved drawings and scope of work. 165 erection, testing & commissioning of spike earthing 20mm x 2500mm gi solid rod 166 excavation of stay pit in following type of soils, as per scope of work, approved drawings and specifications: 167 normal soil 168 erection of complete stay set with gi stay wire ( 7x3.15 mm dia ) , binding of stay wire, by providing guy stay insulator and 0.2 cmt concreting 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) as per technical specifications, approved drawings and scope of works. 169 erection, testing and commissioning of 11 kv insulator including their hardware fittings as per technical specification, approved drawings and scope of work. 170 erection of 5 kn 11 kv polymer with pin insulator 171 erection of 45 kn 11 kv polymer disc insulator with strain hardware 172 laying out, tensioning, binding of conductor and tightening of stays and stringing, testing and commissioning of acsrconductor of following sizes including jointing sleeves, helical formed fittings, jumpering and by providing & erecting pg clamps etc as required as per approved drawings, scope of work and technical specifications 173 stringing of 6 / 2.59 + 1 / 2.59 mm ( 30 mm² al. area ) weasel 174 erection, testing and commissioning of vertical type 11 kvab switch along with support insulators, base channel, down pipe, arcing horns etc. complete asper technical specifications, scope of works and approved drawings 175 erection, testing & commissioning of 11 kv line for under ground railway crossing by2 nos ( including one spare ) 3cx185 sqmm xlpe armored cable ( 0.3 km each ) , using 150mm dia gi pipes, outdoor heat shrinkable cable jointing kits, lugs, 4 nosgi 3 meters long earthing pipe, 6 swg gi wires, cable markers, clamps, jumpering and 11 kv station type lightening arrestors ( 6 nos. ) , etc as required as per technical specifications, approved drawings and scope of he work. 176 erection, testing & commissioning of 11 kv line for under ground highway crossing by2 nos ( including one spare ) 3cx185 sqmm xlpe armored cable ( 0.3 km each ) , using 160 mm hdpe pipe at road crossing, 150mm dia gi pipes for cable support, outdoor heat shrinkable cable jointing kits, lugs, 4 nosgi 3 meters long earthing pipe, 6 swg gi wires, 7 / 20 gi wire, cable markers, clamps, jumpering, 11 kv station type lightening arrestors ( 6 nos. ) , etc as required as per technical specifications, approved drawings and scope of he work. 177 erection of 12 kv, 1250 a, 25ka for 3 seconds, 3 ph, indoor typevacuum circuit breaker with adopter panel for out going feeder by leveling, alignment and welding on existing cable trench in control room. testing & commissioning of indoor vcb panel including 3 nos indoor type current transformer, a meter, volt meter, relay & accessories protection as per approved drawings, technical specifications and scope of the work.: 178 providing and fixing of sign board includingmaterial and its fabrication , painting , writing , logo and scheme etc as per rdss guidelines and t.s 179 laying, erection, termination using indoor & outdoor termination kit, 11kv 3x 185 sqmm xlpearmored power cablesas per technical specifications, approved drawings and scope of works. : 180 erection, testing & commissioning of new gi wire for earthing and guarding as per technical specification, approved drawings and scope of work. 181 erection of 6 swg gi wire 182 erection of 8 swg gi wire 183 extension of control room of 33 / 11 kv substation to accommodate vcb for new 11 kv feeders as per technical specification, approved drawing and scope of work. 184 design, engineering construction of control room building extension 300 sq feet including cost ofall materials, t&p and labour, etc. as per technical specification and approved drawing as per direction of employer 185 shifting of following distribution transformer along with fixture including dismantling , shifting and erection from one location to another location as per approved survey. 186 single phase transformer 187 three phase transformer 188 erection for augmentation of lines 189 erection for augmentation of 33 kv line 190 excavation of additional pole pit ( of depth 1 / 6th of pole length ) in normal soil as per scope of work, approved drawings and specifications: 191 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 ( is 2713, pt i, ii, iii 1980 ) 192 erection of following types of additional poles matching with existing line supports by installing danger plate, anti climbing devices ( barbed wire ) , painting with red oxide & aluminum paint including paint, pole numbering including cement concrete foundation using 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) etc as per scope of work, approved drawings and specifications: 193 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 ( is 2713, pt i, ii, iii 1980 ) cement concreting 0.5 cmt + 0.014 cmt ( muffing ) 194 excavation of stay pit for 33 kv stay in following type of soils, as per scope of work, approved drawings and specifications: 195 normal soil 196 erection of complete stay set with gi stay wire ( 7x4.00 mm dia ) , binding of stay wire, by providing guy stay insulator and 0.3 cmt concreting 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) as per technical specifications, approved drawings and scope of works. 197 erection, testing and commissioning of 33 kv insulator including their hardware fittings as per technical specification, approved drawings and scope of work. 198 erection of 33 kv 10 kn pin insulator with gi pin 199 erection of 33 kv 70 kn disc insulator with strain hardware ( set of 3, 11 kv disc insulators ) 200 erection, testing & commissioning of new pre fabricated hdg steel items like v cross arm, top clamp, cross arm, bracket, clamps, cross bracings, bracings, strain plate, guarding channels, back clamp, etc made of ms channels, ms angle, ms flats of given sizes for over head structures as per technical specification, approved drawings and scope of work. 201 dismantling of existing overhead line conductor and fittings, depositing the dismantled material to employers store and laying out & stringing of new acsr conductor of following sizes by providing jointing sleeves, binding wire & tape & helical formed fittings etc as required as per technical specification, approved drawings and scope of work. 202 stringing of 6 / 4.72 mm+7 / 1.57 mm ( 100 mm² al. area ) dog replacing existing racoon conductor 203 stringing of 30 / 3.00 + 7 / 3.00 mm ( 200 mm² al. area ) panther replacing existing dog / racoon conductor 204 erection, testing & commissioning of 33 kvunder ground cable by2 nos ( including one spare ) 3cx300 sqmm xlpe armored cable, using 160 mm hdpe pipe at road crossing, 150mm dia gi pipes for cable support, outdoor heat shrinkable cable jointing kits, lugs, cable markers, clamps, jumpering, 7 / 20 gi wire etc as required as per technical specifications, approved drawings and scope of he work. 205 erection for augmentation of 3 phase 33 kv line using new insulator and hardware as per technical specification, approved drawings and scope of work 206 erection of 33 kv 70 kn polymer disc insulator along with suitable hardware fittings 207 erection of 33 kv 10 kn polymer pin insulators 208 erection, testing & commissioning of earthing as per technical specifications, approved drawings and scope of work. 209 8 swg gi coil 115 turns ( 1.85 kg ) 210 erection, testing & commissioning of new gi wire for earthing and guarding as per technical specification, approved drawings and scope of work. 211 erection of 6 swg gi wire 212 erection of 8 swg gi wire 213 erection for augmentation of 11 kv lines 214 excavation of additional pole pit ( of depth 1 / 6th of pole length ) in normal soil as per scope of work, approved drawings and specifications: 215 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 216 erection of following types of poles for 11 kv overhead line by installing danger plate, anti climbing devices ( barbed wire ) , pole numbering including cement concrete foundation using 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) etc as per scope of work, approved drawings and specifications: 217 erection of 8.5 m / 180 kgs pcc poles withbase stone pad ( state practices of pcc pole and base plate / stone to be used ) 218 excavation of stay pit in following type of soils, as per scope of work, approved drawings and specifications: 219 normal soil 220 erection of complete stay set with gi stay wire ( 7x3.15 mm dia ) , binding of stay wire, by providing guy stay insulator and 0.2 cmt concreting 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips ( 1:2:4 ) as per technical specifications, approved drawings and scope of works. 221 erection, testing and commissioning of 11 kv insulator including their hardware fittings as per technical specification, approved drawings and scope of work. 222 erection of 11 kv pin insulator with gi pin 223 erection of 11 kv disc insulator with strain hardware 224 dismantling of existing overhead line conductor & fittings and depositing to employers store, laying out, tensioning, binding of new conductor and tightening of stays and stringing, testing and commissioning of acsrconductor of following sizes including jointing sleeves, helical formed fittings, jumpering and by providing & erecting pg clamps etc as required as per approved drawings, scope of work and technical specifications 225 stringing of 6 / 2.59 + 1 / 2.59 mm ( 30 mm² al. area ) weasel by replacing existing weasel / squirrel conductor 226 stringing of 6 / 3.35 + 1 / 3.35 mm ( 50 mm² al. area ) rabbit by replacing existing weasel / squirrel conductor 227 stringing of 6 / 4.72 mm+7 / 1.57 mm ( 100 mm² al. area ) dog by replacing existing racoon / rabbit conductor 228 erection, testing & commissioning of pre fabricated hdg steel items like v cross arm, top channel, top clamp, cross arm, bracket, clamps, cross bracings, bracings, strain plate, guarding channels, back clamp, etc made of ms channels, ms angle, ms flats of given sizes for over head structures and hdg ms nuts, bolts & washers as per technical specification, approved drawings and scope of work. 229 erection, testing and commissioning of 11 kv insulator including their hardware fittings as per technical specification, approved drawings and scope of work. 230 erection of 5 kn 11 kv polymer pin insulator 231 erection of 45 kn 11 kv polymer disc insulator with strain hardware 232 earthingand guarding arrangement as per technical specifications, approved drawings and scope of work. 233 erection, testing & commissioning of spike earthing 20mm solid rod 234 erection of 8 swg gi wire for earthing and guarding 235 erection of 6 swg gi wire for earthing and guarding 236 erection of dt capacitor 237 erection, testing & commissioning offollowing 440 volt lt shunt capacitor including mounting structure and accessories as required as per technical specifications, approved drawings and scope of work. 238 erection of lt shunt capacitor 440 volt 10 kvar 3phase 50hz ip65 239 erection of lt shunt capacitor 440 volt 16 kvar 3phase 50hz ip65 240 erection of lt shunt capacitor 440 volt 25 kvar 3phase 50hz ip65 241 erection of lt shunt capacitor 440 volt 40 kvar 3phase 50hz ip65 242 erection of lt shunt capacitor 440 volt 63 kvar 3phase 50hz ip65 243 erection of lt shunt capacitor 440 volt 100 kvar 3phase 50hz ip65 244 discount offered in % 245 words final quoted price after discount...

Kisan Sahkari Chini Mills Limited - Uttar Pradesh

33415901 supply of new i.d. fan for 20 tph boiler ice berg / aerotech / kamar baghsey make new i.d. fan for 20 tph boiler ice berg / aerotech / kamar baghsey make , new i.d. fanfor 20 tph boiler ice berg / c.b. doctor / aerotech / kamar baghsey make , fabrication & supply of new i.d. fan impeller with hub & shaft identical in all respect to our existing fan for m / si.j.t. make 20 tph capacity bagasse fired boiler having ventury type wet scrubber after i.d. fan, having following specification: fan rpm 900, no of blades 09 nos, blade length 730mm, blades must have hard faced wear pad. shaft moc en 08 for ged , shaft must be ultrasonically tested with test report impeller od 1875mm, impeller width at top 200mm, back plate 12mm thick with 10mm thick wear plate, shaft length 1550mm, keyway 90mm long x 25mm width x 06mm depth, fitted bearing 22222k, shaft od 100mm, pulley size 90mm, suction id 800mm, shroud 6mm, finishing heat resistance aluminium paint fan must be dynami cally balanced with report....

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

33384460 development of distribution infrastructure at [ raebareilly, sitapur, unnao ] district of uttar pradesh under revamped reforms based and results linked, distribution sector scheme 1 lt line with xlpe armoured cable in high loss area 2 route survey and pole spotting and mapping ( as per employer requirement of sbd ) 3 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 4 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 5 13 m long steel tubular poles with welded steel base plate of designation 410 sp 72 6 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 7 foundation of pcc supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.268 cmt for each support ) 8 stone pad for supports as per scope of works & drawing ( 300x300x75 mm ) 9 red oxide paint as per ts 10 aluminium paint as per ts 11 1.1 kv single core 25sqmm xlpe armoured cable ( 1cx25 sqmm ) 12 1.1 kv single core 50sqmm xlpe armoured cable ( 1cx50 sqmm ) 13 1.1 kv single core 95sqmm xlpe armoured cable ( 1cx95 sqmm ) 14 1.1 kv single core 120sqmm xlpe armoured cable ( 1cx120 sqmm ) 15 lt cross arm arrangement angel ( 50x50x6mm ) ( 50x8mm ) ( weight 9.41 kg ) with nuts and bolts 16 lt cross arm arrangement angel ( 75x75x8mm ) ( 65x8mm ) ( weight 18.6 kg ) with nuts and bolts 17 c clamp with nut & bolts 18 lt shakle insulator 19 distribution tie for shakle insulator 20 mid span joint 25sqmm 21 mid span joint 50sqmm 22 mid span joint 95sqmm 23 mid span joint 120sqmm 24 three phase 20swg crca ms sheet by deep drawn / sheet bending processpole top distribution box with calmps ( 50x6 mm ) and nut & bolts and lugs suitable for 25 sqmm armoured cable 25 three single phase 20swg crca ms sheet by deep drawn / sheet bending processpole top distribution box with calmps ( 50x6 mm ) and nut & bolts and lugs suitable for 50 sqmm armoured cable 26 three phase 20swg crca ms sheet by deep drawn / sheet bending processpole top distribution box with calmps ( 50x6 mm ) and nut & bolts and lugs suitable for 95 sqmm armoured cable 27 three phase 20swg crca ms sheet by deep drawn / sheet bending processpole top distribution box with calmps ( 50x6 mm ) and nut & bolts and lugs suitable for 120 sqmm armoured cable 28 1x2.5 sqmm pvc insulated aluminium cable for energising the street light. 29 5a, 240 v, isi marked piano type switch 30 earthing of pole by earthing coil ( with salt & charcoal ) 31 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 32 removal of existing material and shifting to mvvnl store 33 armoured cabling in consumer service connection 34 single phase ( 2cx4 sqmm ) pvc armoured service cable 35 single phase ( 2cx6 sqmm ) pvc armoured service cable 36 three phase ( 4cx16 sqmm ) pvc armoured service cable 37 supporting gi wire 10 swg ( as per site requirements ) 38 20 swg gi wire for binding 39 arrangement for holding the service cable at pole ( ms flat 50x8 mm, 3.0 kg ) with nuts and bolts 40 arrangement for holding the service cable at pole ( ms flat 75x8 mm, 4.6 kg ) with nuts and bolts 41 ms angle 50x50x5 mm for holding the service cable at consumer premises ( length 1000 mm ) 42 polycarbonated box for single phase consumer 43 polycarbonated box for three phase consumer 44 removal of existing material and shifting to mvvnl store 45 replacement of bare conductors / damage cable with ab cables 46 route survey and pole spotting and mapping ( as per employer requirement of sbd ) 47 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 48 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 49 13 m long steel tubular poles with welded steel base plate of designation 410 sp 72 50 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 51 foundation of pcc supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.268 cmt for each support ) 52 stone pad for supports as per scope of works & drawing ( 300x300x75 mm ) 53 red oxide paint as per ts 54 aluminium paint as per ts 55 single phase glass fiber reinforced polyester sheet moulding compound ( smc ) pole top distribution box with calmps ( 40x3 mm ) and nut & bolts 56 three phase glass fiber reinforced polyester sheet moulding compound ( smc ) pole top distribution box with calmps ( 40x3 mm ) and nut & bolts 57 2cx25 sqmm xlpe aluminium conductor cable for single phase db incomer 58 4cx35 sqmm xlpe aluminium conductor cable for three phase db incomer 59 earthing of pole by earthing coil ( with salt & charcoal ) 60 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 61 aerial bunched xlpe cable 1x25 ( ph ) + 1x25 ( bare messenger cum neutral ) + 1x16 ( insulated street lighting ) sqmm 62 aerial bunched xlpe cable 3x50 ( ph ) + 1x35 ( bare messenger cum neutral ) + 1x16 ( insulated street lighting ) sqmm 63 aerial bunched xlpe cable 3x95 ( ph ) + 1x70 ( bare messenger cum neutral ) + 1x16 ( insulated street lighting ) sqmm 64 aerial bunched xlpe cable 3x120 ( ph ) + 1x95 ( bare messenger cum neutral ) + 1x16 ( insulated street lighting ) sqmm 65 aerial bunched xlpe cable 3x150 ( ph ) + 1x120 ( bare messenger cum neutral ) + 1x16 ( insulated street lighting ) sqmm 66 lt pole clamp ( 50x8mm ) ( 2.56 kg ) with nut and bolts 67 lt eye hook 68 suspension clamp 69 dead end clamp 70 insulation piercing connectors / connector type i ( ab cable to ab cable ) 71 insulation piercing connectors type ii ( ab cable to service cable ) 72 removal of existing material and shifting to mvvnl store 73 1x2.5 sqmm pvc al cable for energising the street light 74 end cap for ab cable 25 sqmm 75 end cap for ab cable 50 sqmm 76 end cap for ab cable 95 sqmm 77 end cap for ab cable 120 sqmm 78 end cap for ab cable 150 sqmm 79 pg clamp for messanger wire 80 provision of ab cables for extra circuits at existing dtr 81 overhead lt for extra circuit at existing dtr 82 route survey and pole spotting and mapping ( as per employer requirement of sbd ) 83 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 84 foundation of pcc supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.268 cmt for each support ) 85 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 86 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 87 stone pad for supports as per scope of works & drawing ( 300x300x75 mm ) 88 red oxide paint as per ts 89 aluminium paint as per ts 90 single phase glass fiber reinforced polyester sheet moulding compound ( smc ) pole top distribution box with calmps ( 40x3 mm ) and nut & bolts 91 three phase glass fiber reinforced polyester sheet moulding compound ( smc ) pole top distribution box with calmps ( 40x3 mm ) and nut & bolts 92 2cx25 sqmm xlpe aluminium conductor cable for single phase db incomer 93 4cx35 sqmm xlpe aluminium conductor cable for three phase db incomer 94 earthing of pole by earthing coil ( with salt & charcoal ) 95 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 96 aerial bunched xlpe cable 1x25 ( ph ) + 1x25 ( bare messenger cum neutral ) + 1x16 ( insulated street lighting ) sqmm 97 aerial bunched xlpe cable 3x50 ( ph ) + 1x35 ( bare messenger cum neutral ) + 1x16 ( insulated street lighting ) sqmm 98 aerial bunched xlpe cable 3x95 ( ph ) + 1x70 ( bare messenger cum neutral ) + 1x16 ( insulated street lighting ) sqmm 99 aerial bunched xlpe cable 3x120 ( ph ) + 1x95 ( bare messenger cum neutral ) + 1x16 ( insulated street lighting ) sqmm 100 aerial bunched xlpe cable 3x150 ( ph ) + 1x120 ( bare messenger cum neutral ) + 1x16 ( insulated street lighting ) sqmm 101 lt pole clamp ( 50x8mm ) ( 2.56 kg ) with nut and bolts 102 lt eye hook 103 suspension clamp 104 dead end clamp 105 insulation piercing connectors / connector type i ( ab cable to ab cable ) 106 insulation piercing connectors type ii ( ab cable to service cable ) 107 1x2.5 sqmm pvc al cable for energising the street light 108 end cap for ab cable 25 sqmm 109 end cap for ab cable 50 sqmm 110 end cap for ab cable 95 sqmm 111 end cap for ab cable 120 sqmm 112 end cap for ab cable 150 sqmm 113 pg clamp for messanger wire 114 feeder segregation 115 overhead 11 kv new feeder 116 route survey and pole spotting and mapping ( as per employer requirement of sbd ) 117 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 118 9 meter long / 400 kg pcc poles ( pcc pole as per state practice ) 119 foundation of pcc supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.268 cmt for each support ) 120 stone pad for supports as per scope of works & drawing ( 300x300x75 mm ) 121 stone pad for supports as per scope of works & drawing ( 450x450x75 mm ) 122 11kv v type cross arm ( m.s channel 75x40x6mm ) welded with ms angel ( 50x50x6 ) ( weight 10.37 kg ) with bolts and nuts 123 cross arm holding clamps ( ms flat 50x8 mm ) ( weight 1.33 kg ) with bolts and nuts 124 f bracket ms flat ( 50x8 mm ) ( weight 1.56 kg ) with nut and bolts 125 cut point top channel ( 100x50x6 mm ) of length 230 mm along with nut & bolts 126 cut point bottom channel ( 100x50x6 mm ) of length 1150 mm along with nut & bolts 127 tapping horizontal cross arm ( 100x50x6 mm ) of length 1020 mm along with calmps ( 50x8 ) and nut and bolts 128 tapping top channel ( 100x50x6 mm ) of length 256 mm along with calmps ( 50x8 ) and nut and bolts 129 dp top channel ( channel 100x50x6mm ) 2240 mm longwith bolts and nuts 130 horizontal belting angle ( angle 50x50x6 mm ) 2240 mm long with bolts and nuts 131 cross bracing angle ( angle 50x50x6 mm ) 2500 mm long with bolts and nuts 132 belting clamp top clamp ( flat 50x8 mm ) ( weight 1.4 kg ) with bolts and nuts 133 belting clamp bottom clamp ( flat 50x8 mm ) ( weight 1.5 kg ) with bolts and nuts 134 fish plate for jumpering 135 6 / 2.59 + 1 / 2.59 mm ( 30 sqmm al. area ) acsr weasel conductors 136 6 / 3.35 + 1 / 3.35 mm ( 50 sqmm al. area ) acsr rabbit conductors 137 6 / 4.72 mm+7 / 1.57 mm ( 100 mm² al. area ) acsr dog conductor 138 pg clamp for weasel conductor 139 pg clamp for rabbit conductor 140 pg clamp for dog conductor 141 distribution tie for pin insulator 142 armoured rod with ferrule 143 jointing sleeves aluminium 144 aluminium binding wire and tape 145 11 kv polymer disc insulator 45 kn ( b&s type ) along with suitable hardware fittings 146 11 kv polymer pin insulators 5 kn with nuts 147 earthing of pole by earthing coil ( with salt & charcoal ) 148 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 149 ms danger board with back calmps & nuts and boltsas per technical specification 150 anti climbing device 3.5 kgs, 2.5mm dia ( 12 swg ) galvanized barbed wire on each 11 kv support as per scope of works &ts 151 numbering of pole of each support as per technical specification and scope of work 152 underground 11 kv new feeder 153 radar route survey for route profile of any utility cables, pipes etc. along the route as per ts and scope of work 154 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 155 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 156 red oxide paint as per ts 157 aluminium paint as per ts 158 dp top channel ( channel 100x50x6mm ) 2240 mm longwith bolts and nuts 159 horizontal belting angle ( angle 50x50x6 mm ) 2240 mm long with bolts and nuts 160 cross bracing angle ( angle 50x50x6 mm ) 2500 mm long with bolts and nuts 161 belting clamp top clamp ( flat 50x8 mm ) ( weight 1.4 kg ) with bolts and nuts 162 belting clamp bottom clamp ( flat 50x8 mm ) ( weight 1.5 kg ) with bolts and nuts 163 fish plate for jumpering 164 11 kv polymer pin insulators 5 kn with nuts 165 heat shrinkable jointing kit indoor for 11 kv 3c×185 sq.mm. xlpe cable 166 heat shrinkable jointing kit indoor for 11 kv 3c×120 sq.mm. xlpe cable 167 heat shrinkable jointing kit outdoor for 11 kv 3c×185 sq.mm. xlpe cable 168 heat shrinkable jointing kit outdoor for 11 kv 3c×120 sq.mm. xlpe cable 169 heat shrinkable cable jointing kit straight through for 11 kv 3c×185 sq.mm. xlpe cable 170 heat shrinkable cable jointing kit straight through for 11 kv 3c×120 sq.mm. xlpe cable 171 road restoration chages for pucca road crossing 172 road restoration chages for kucchha road crossing 173 supply and placing of pre cast concrete manhole chambers of size 900mm x 900mm internal dimension x 800mm height & 100mm wall thickness ( heavy duty ) with concrete cover of 100mm thickness in the specified locations in the trench. 174 supply & erection of 11 kv single core 95 sqmm xlpe aluminium cable for jumpering 175 supply & erection of aluminum lugs 185 sq.mm. 176 supply & erection of aluminum lugs 120 sq.mm. 177 supply & erection of cable warning tape 178 fixing of cable marker on cable route and inscription of feeder name and voltage on cable marker 179 supply of 11 kv 3c×120 sqmm xlpe cable 180 supply of 11 kv 3c×185 sqmm xlpe cable 181 earth digging, laying, termination / jointing, erection, testing & commissioning of 11 kv grade 3 core 120 / 185 sqmm xlpe power cable underground and backfilling with bricks, sands, excavated soil as per standard practise, levelling etc complete in all respect along with all accessories, earthing etc. and as per ts / approved drawing. 182 laying of 11 kv 3cx185 sq mm xlpe singlecableby digging of trench 1100 mm, deep, 750 mm wide its boxing with brick, sand, stone slabafter laying of cable separation of cable by brick wall up to stone slab filling and proper levelling& ramming. the ferruling of cable also include in this work ( all the material ) 183 laying of 11 kv 3x185 sq mm xlpe twin cableby digging of trench 1100 mm deep, 750 mm wide its boxing with brick, sand, stone slab after laying of cable separation of cable by brick wall up to stone slab filling and proper levelling & ramming. the ferruling of cable also include in this work ( all the material ) 184 laying of 11 kv 3cx120 sq mm xlpe singlecableby digging of trench 1100 mm, deep, 750 mm wide its boxing with brick, sand, stone slabafter laying of cable separation of cable by brick wall up to stone slab filling and proper levelling& ramming. the ferruling of cable also include in this work ( all the material 185 laying of 11 kv 3x120 sq mm xlpe twin cableby digging of trench 1100 mm deep, 750 mm wide its boxing with brick, sand, stone slab after laying of cable separation of cable by brick wall up to stone slab filling and proper levelling & ramming. the ferruling of cable also include in this work ( all the material ) 186 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection, testing & commissioning of 11 kv grade 3 core 120 / 185 sqmm xlpe power cable undergroundusing hdpe pipecomplete in all respect along with all accessories, earthing etc. and as per ts / approved drawing . 187 laying of 11 kv 3c×185 sqmm xlpe cable 188 laying of 11 kv 3×120 sqmm xlpe cable 189 pipe ( hdpe 160 mm dia ) for cable laying 190 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection, testing & commissioning of 11 kv grade 3 core 120 / 185 sqmm xlpe power cable undergroundwithout hdpe pipes in all respect along with all accessories, earthing etc. and as per ts / approved drawing . 191 laying of 11 kv 3c×185 sqmm xlpe cable 192 laying of 11 kv 3×120 sqmm xlpe cable 193 hoisting of following sizes of11 kv single cable on existing / erected double pole including gi pipe 3 mtr long 6 dia including jumpering, dressing of cable with required all necessary clamps and nut, bolts. ( all the material shall be arranged by contractor ) 194 testing & commissioning of 11 kv grade 3 core 185 sqmm xlpe power underground cable 195 testing & commissioning of 11 kv grade 3 core 120 sqmm xlpe power underground cable 196 earthing of pole by earthing coil ( with salt & charcoal ) 197 8 swg gi wire for pole, db earthing with gi nuts, bolts & washers 198 ms danger board with back calmps & nuts and boltsas per technical specification 199 anti climbing device 3.5 kgs, 2.5mm dia ( 12 swg ) galvanized barbed wire on each 11 kv support as per scope of works & ts 200 numbering of pole of each support as per technical specification and scope of work 201 railway crossing 202 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 203 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 204 red oxide paint as per ts 205 aluminium paint as per ts 206 dp top channel ( channel 100x50x6mm ) 2240 mm longwith bolts and nuts 207 horizontal belting angle ( angle 50x50x6 mm ) 2240 mm long with bolts and nuts 208 cross bracing angle ( angle 50x50x6 mm ) 2500 mm long with bolts and nuts 209 belting clamp top clamp ( flat 50x8 mm ) ( weight 1.4 kg ) with bolts and nuts 210 belting clamp bottom clamp ( flat 50x8 mm ) ( weight 1.5 kg ) with bolts and nuts 211 fish plate for jumpering 212 11 kv polymer pin insulators 5 kn with nuts 213 9 kv, 10 ka station class la 214 supply of 11 kv 3c×185 sqmm xlpe cable 215 supply of 33 kv 3c×300 sqmm xlpe cable 216 heat shrinkable jointing kit outdoor for 11 kv 3c×185 sq.mm. xlpe cable 217 heat shrinkable jointing kit outdoor for 33 kv 3c×300 sq.mm. xlpe cable 218 hoisting of following sizes of11 kv single cable on existing / erected double pole including gi pipe 3 mtr long 6 dia including jumpering, dressing of cable with required all necessary clamps and nut, bolts. ( all the material shall be arranged by contractor ) 219 11 kv or 33 kv lineforunder ground railway crossing by 2 nos ( including one spare ) 3cx185 or 3cx300 sqmm xlpe armoured cable using 150mm dia gi pipes ( grade a for underground laying and grade b for pole support ) , outdoor heat shrinkable cable jointing kits, lugs, 4 nos gi 3 meters long pipe, earthing, 8 swg gi wires, cable markers, bi metallick clamps, jumpering , as required as per technical specifications, drawings and scope of the work. 220 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection of 11 kv grade 3 core 185 sqmm xlpe power cable underground as per ts / approved drawing . 221 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection of 33 kv grade 3 core 300 sqmm xlpe power cable underground as per ts / approved drawing . 222 digging of trench by excavation of earth, laying of bricks to cover the cable and filling of sand & earth ramming and dressing properly with complete job for laying 11 kv xlpe cables including cost of bricks, sand, clamps etc. 223 digging of trench by excavation of earth, laying of bricks to cover the cable and filling of sand & earth ramming and dressing properly with complete job for laying 33 kv xlpe cables including cost of bricks, sand, clamps etc. 224 g.i. pipe ( 6 dia. ) forlaying ug below the railway track ( minimum 3 meter ) by hdd method. 225 supply & erection of 11 kv single core 95 sqmm xlpe aluminium cable for jumpering 226 supply & erection of 33 kv single core 120 sqmm xlpe aluminium cable for jumpering 227 supply & erection of aluminum lugs 185 sq.mm. 228 supply & erection of aluminum lugs 300 sq.mm. 229 railway crossing documentation and approval fee etc. 230 testing & commissioning of 11 kv grade 3 core 185 sqmm xlpe power underground cable 231 testing & commissioning of 33 kv 3 core 300 sqmm xlpe power underground cable 232 earthing of pole by earthing coil ( with salt & charcoal ) 233 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 234 ms danger board with back calmps & nuts and boltsas per technical specification 235 anti climbing device 3.5 kgs, 2.5mm dia ( 12 swg ) galvanized barbed wire on each 11 kv support as per scope of works &ts 236 numbering of pole of each support as per technical specification and scope of work 237 national highway crossing 238 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 239 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 240 red oxide paint as per ts 241 aluminium paint as per ts 242 dp top channel ( channel 100x50x6mm ) 2240 mm longwith bolts and nuts 243 horizontal belting angle ( angle 50x50x6 mm ) 2240 mm long with bolts and nuts 244 cross bracing angle ( angle 50x50x6 mm ) 2500 mm long with bolts and nuts 245 belting clamp top clamp ( flat 50x8 mm ) ( weight 1.4 kg ) with bolts and nuts 246 belting clamp bottom clamp ( flat 50x8 mm ) ( weight 1.5 kg ) with bolts and nuts 247 fish plate for jumpering 248 11 kv polymer pin insulators 5 kn with nuts 249 9 kv, 10 ka station class la 250 supply & erection of 11 kv single core 95 sqmm xlpe aluminium cable for jumpering 251 supply & erection of 33 kv single core 120 sqmm xlpe aluminium cable for jumpering 252 supply & erection of aluminum lugs 185 sq.mm. 253 supply & erection of aluminum lugs 300 sq.mm. 254 supply of 11 kv 3c×185 sqmm xlpe cable 255 supply of 33 kv 3c×300 sqmm xlpe cable 256 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection, testing & commissioning of 11 kv grade 3 core 185 or 300 sqmm xlpe power cable underground as per ts / approved drawing . 257 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection of 11 kv grade 3 core 185 sqmm xlpe power cable underground as per ts / approved drawing . 258 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection of 33 kv grade 3 core 300 sqmm xlpe power cable underground as per ts / approved drawing . 259 pipe ( hdpe 160 mm dia ) for cable laying at road crossings 260 heat shrinkable jointing kit outdoor for 11 kv 3c×185 sq.mm. xlpe cable 261 heat shrinkable jointing kit outdoor for 11 kv 3c×300 sq.mm. xlpe cable 262 hoisting of following sizes of11 kv single cable on existing / erected double pole including gi pipe 3 mtr long 6 dia including jumpering, dressing of cable with required all necessary clamps and nut, bolts. ( all the material shall be arranged by contractor ) 263 digging of trench by excavation of earth, laying of bricks to cover the cable and filling of sand & earth ramming and dressing properly with complete job for laying 11 kv xlpe cables including cost of bricks, sand, clamps etc. 264 digging of trench by excavation of earth, laying of bricks to cover the cable and filling of sand & earth ramming and dressing properly with complete job for laying 33 kv xlpe cables including cost of bricks, sand, clamps etc. 265 testing & commissioning of 11 kv grade 3 core 185 sqmm xlpe power underground cable 266 testing & commissioning of 33 kv 3 core 300 sqmm xlpe power underground cable 267 earthing of pole by earthing coil ( with salt & charcoal ) 268 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 269 ms danger board with back calmps & nuts and boltsas per technical specification 270 anti climbing device 3.5 kgs, 2.5mm dia ( 12 swg ) galvanized barbed wire on each 11 kv support as per scope of works &ts 271 numbering of pole of each support as per technical specification and scope of work 272 supply & installation of 11kv vcb switchgear panel outgoing for extra feeder under feeder segregation / bifurcartion works. 273 control room extension 274 excavation in foundation in ordinary soil ( loam day or sand ) including lift upto 1.5 mtr. and lead upto 30 m and including filling watering and ramming of excavated earth into the building and sides of the foundation trenches or in to the plinth and directed by the engineer in charge upto a distance of 30 m from the foundation 275 concrete with 4 cm.gauge 1st class brick ballast ( class 150 ) coarse sand ( f.m.1.8 to 2.5 ) and cement in proportion of 10:5:1 in foundation and under floors including supply of all materials labour and t&p etc. required for propoer complrtion of work. 276 1st class brick work in 1:6 cement & coarse sand ( f.m.1.8 to 2.5 ) morter in foundation & plinth including supply of all materials, labour and t&p etc. required for propoer complrtion of work. 277 1st class brick ( class 150 ) work in 1:6 cement & coarse sand ( fm 1.8 to 2.50 ) morter but in supper structure but for wall of one & half brick thick including supply of all materials , labour t&p etc required for propoer completion of work. 278 st class brick ( class 150 ) work in 1:6 cement & coarse sand ( fm1.8 to 2.50 ) morter but in supper structure but for wall of one brick thick including supply of all materials , labour t&p etc required for proper completion of work. 279 mild steel or iron in plain work such as reinforced concrete or reinforced brick work ( when not included in over all rate ) wrought to required shape as necessary i / c bending for proper completion of the work & i / c supply of steel its wastege shall be measured stee! shall not be supplied by the department. 280 mild steel or iron work in heavy sizes such as trusses built up gates, door frames, record racks roof work gates etc. wrought to required form including holes riveting or welding where necessary and also including supply of steel bolts nuts wastage etc.and their fixing required for proper completion of the work ( steel is not supplies by the department ) 281 r.c.c. work with cement approved coarse sand ( p.m. 1.8 to 2.5 ) and 2 cm gauge graded approved hard stone ballast in proportion 1:2:4 in lintels of doors & windows excluding supply of reinforcement and its bending but including its fixing & binding the same with 24 bwg g.i. binding wire and including necessary centring & shuttering etc. and also including cost of all materials, labour and t&p etc. required for proper completion of the work. 282 r.c.c. work with cement approved coarse sand ( p.m. 1.8 to 2.5 ) and 2 cm gauge graded approved hard stone ballast in proportion 1:1:5:3 for slab excluding supply of reinforcement and its bending but including its fixing & binding the same with 24 bwg g.i binding wire and i / c necessary centering & shuttering etc. and also i / c cost of all materials, labour and t&p etc. required for proper completion of the work. 283 12 mm thick plaster with cement morter consisting of 1 aart: sparts of approved coarse sand on fare surface ncluding supply of all materials, labour t&p etc. required for proper completion of work. 284 supply & fixing fan hooks 16 mm dia 200 mm long complete. 285 p / f glass strip of 40 mm depth in joints of floor and skirting at the time of laying, floors flush with floor level ncluding labour. tools and plants etc. complete. 286 40 mm thick 1:2:4 floor without base concrete floor with cement, approved coarse sand &2 cm. graded approved stone ballast ( shingle for bareily ) laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and giving them a uniform finish including supply of all labour and t&p etc required for proper completion of work. 287 white washing three coats of new surface including cost of all materials, labour and t&p etc. required for proper completion of the work exept cost of angle iron and flat. 288 one priming coat and two coats of dry distemper castle or equivalent make on new surface including cost of all materials, labour and t&p etc. required for proper completion of the work. 289 finishing walls with water proof cement paint of approved make and quality over new work with three coats to give an even shade including supply of all materials, labour and t&p etc.required for proper completion of the work. 290 writing point for light with 1.5 sq.mm. frpvc insulated multistrand single core copper conductor cable in surface conduit pipe, complete with copper earth continuity wire, piano type switch & ceiling rose / angle / button holder on 3mm thick phenolic aminated backelite sheet etc. complete in all respects, as directed including matching colour wash. 291 wiring point for fan / fresh air fan ( light duty exhaust fan ) n pvc conduit with 1.5 sq.mm. fr pvc insulted multistrand copper condctor cable as earth wire drawn nside the conduit. 292 s / f batten / angle holder of approved quality complete n all respect. 293 painting or varnishing on new iron work in small areas or new wood work with one coat of ready mixed priming paint and two coats of approved superior quality ready mixed paint ( luxol ) or equivalent brand or varnish i / c supply of all materials, labour t&p etc. required for proper completion of work.paint to be used should conform i.s.103 1950 294 dismantling brick work or stone work in time or cement mortar and including stacking of materials as directed by e / l within distance of 60mtr. 295 dismantling existing plaster including disposal of refuse as directed by e / l within a distance of 60 mtr. 296 dismantling c.c brick or brick or granolithic floors including base concrete and including stacking of dismantled material as directed by e / l within a distance of 60 mtr. 297 road crossings on 9 meter and 11 meter poles 298 9 meter long / 400 kg pcc poles ( pcc pole as per state practice ) 299 foundation of pcc supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.268 cmt for each support ) 300 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 301 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 302 stone pad for supports as per scope of works & drawing ( 450x450x75 mm ) 303 red oxide paint as per ts 304 aluminium paint as per ts 305 v cross arm supporting channel ( 100x50x6 mm ) , 3000mm long with holding clamps , bolts and nuts. 306 11kv v type cross arm ( m.s channel 75x40x6mm ) welded with ms angel ( 50x50x6 ) ( weight 10.37 kg ) with bolts and nuts 307 11kv bridling v type cross arm ( m.s channel 75x40x6mm ) welded with ms angel ( 50x50x6 ) ( weight 10.5 kg ) with bolts and nuts 308 guarding cross arm ( 75x40x6 mm ) 2210 mm long with eye bolts ( 16mm dia ) 309 back clamp for guarding cross arm ( 50x8 mm ) ( weight 1.15 kg ) with nut & bolts. 310 cross arm holding clamps ( ms flat 50x8 mm ) ( weight 1.33 kg ) with bolts and nuts 311 f bracket ms flat ( 50x8 mm ) ( weight 1.56 kg ) with nut and bolts 312 distribution tie for pin insulator 313 11 kv polymer pin insulators 5 kn with nuts 314 6 swg gi wire along the span 315 8 swg gi wire across the span 316 12 swg gi wire for binding 317 earthing of pole by earthing coil ( with salt & charcoal ) 318 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 319 ms danger board with back calmps & nuts and boltsas per technical specification 320 anti climbing device 3.5 kgs, 2.5mm dia ( 12 swg ) galvanized barbed wire on each 11 kv support as per scope of works &ts 321 numbering of pole of each support as per technical specification and scope of work 322 relocation of 11 / .433 kv 3ph distribution transformer 323 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 324 foundation of pcc supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.268 cmt for each support ) 325 stone pad for supports as per scope of works & drawing ( 300x300x75 mm ) 326 shifting of distribution transformer and all fabricated items and other allied materials 327 distribution transformer for segregated feeders 328 9 meter long / 400 kg pcc poles ( pcc pole as per state practice ) 329 foundation of pcc supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.268 cmt for each support ) 330 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 331 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 332 stone pad for supports as per scope of works & drawing ( 450x450x75 mm ) 333 red oxide paint as per ts 334 aluminium paint as per ts 335 transformer top channel ( 100x50x6mm ) 2800 mm long with nuts & bolts 336 ab switch mounting channel ( 100x50x6mm ) 2800 mm long with nuts & bolts 337 back clamp for ab switch mounting channel ( 50x8mm ) ( weight 1.8 kg ) with nuts & bolts 338 do fuse mounting channel ( 75x40x6mm ) 2800 mm long with nuts & bolts 339 back clamp for do fuse mounting channel ( 50x8mm ) ( weight 1.9 kg ) with nuts & bolts 340 transformer mounting channel ( 100x50x6mm ) 2800 mm with nuts & bolts 341 transformer mounting channel support ( 50x50x6mm ) 500 mm long with nuts & bolts. 342 transformer belting angle ( 50x50x6mm ) 2800 mm longwith nuts & bolts 343 transformer belting angle support ( 35x35x6 mm ) 500 mm long with nuts & bolts 344 11 kv polymer disc insulator 45 kn ( b&s type ) along with suitable hardware fittings 345 11 kv polymer pin insulators 5 kn with nuts 346 11 / 0.230 kv distribution transformer 16 kva single phase aluminum wound dtr 347 11 / 0.4 kv distribution transformer 25 kva three phase aluminum wound dtr 348 11 / 0.4 kv distribution transformer 63 kva three phase aluminum wound dtr 349 11 / 0.4 kv distribution transformer 100 kva three phase aluminum wound dtr 350 11 / 0.4 kv distribution transformer 250 kva three phase copper wound dtr 351 acsr weasel counductor for jumpering 352 bimetallic connector for ht & lt side of the transformer 353 t clamp & pg clamp for jumpering 354 lt distribution box polyester sheet moulding compound ( smc ) for 16 kva distribution transformer with arrangement of suitable bus bars and mccbs as per scope of works of sbd 355 lt distribution box polyester sheet moulding compound ( smc ) for 25 kva distribution transformer with arrangement of suitable bus bars & mccbs as per scope of works of sbd 356 lt distribution box polyester sheet moulding compound ( smc ) for 63 kva distribution transformer with arrangement of suitable bus bars & mccbs as per scope of works of sbd 357 lt distribution box polyester sheet moulding compound ( smc ) for 100 kva distribution transformer with arrangement of suitable bus bars & mccbs as per scope of works of sbd 358 lt distribution box polyester sheet moulding compound ( smc ) for 250 kva distribution transformer with arrangement of suitable bus bars & mccbs as per scope of works of sbd 359 back clamp support for ltdb ( 65x8 mm ) 360 whole current a.c. single phase smart energy meter 361 whole current a.c. three phase smart energy meter 362 1cx16 sqmm 1.1kv xlpe cable with suitable lugs and glands and cable ties 363 1cx35 sqmm 1.1kv xlpe cable with suitable lugs and glands and cable ties 364 1cx70 sqmm 1.1kv xlpe cable with suitable lugs and glands and cable ties 365 1cx150 sqmm 1.1kv xlpe cable with suitable lugs and glands and cable ties 366 clamps for lt service cable support 367 9 kv, 5 ka distribution class la 368 11 kv, 3 ph, 200 a, 3 pin type vertical mounting typeab switch along with support insulators, base channel, down pipe, operating handle and support, etc. complete asper technical specifications, scope of works and approved drawings 369 11 kv, 3 ph, drop out fuse set ( set of 3 units ) along with support insulators, base channel, fuse barrel etc. complete asper technical specifications, scope of works and approved drawings 370 gi earthing pipe of 40 mm dia & 3000 mm long as per is 1161 371 gi flat ( 50x6 mm ) 372 gi wire 8swg 373 gi flat ( 25x3 mm ) 374 ms danger board with back calmps & nuts and boltsas per technical specification 375 anti climbing device 3.5 kgs, 2.5mm dia ( 12 swg ) galvanized barbed wire on each 11 kv support as per scope of works &ts 376 numbering of pole of each support as per technical specification and scope of work 377 lt line for segregated feeders 378 route survey and pole spotting and mapping ( as per employer requirement of sbd ) 379 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 380 foundation of pcc supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.268 cmt for each support ) 381 stone pad for supports as per scope of works & drawing ( 300x300x75 mm ) 382 single phase glass fiber reinforced polyester sheet moulding compound ( smc ) pole top distribution box with calmps ( 40x3 mm ) and nut & bolts 383 three phase glass fiber reinforced polyester sheet moulding compound ( smc ) pole top distribution box with calmps ( 40x3 mm ) and nut & bolts 384 2cx25 sqmm xlpe aluminium conductor cable for single phase db incomer 385 4cx35 sqmm xlpe aluminium conductor cable for three phase db incomer 386 earthing of pole by earthing coil ( with salt & charcoal ) 387 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 388 aerial bunched xlpe cable 1x25 ( ph ) + 1x25 ( bare messenger cum neutral ) + 1x16 ( insulated street lighting ) sqmm 389 aerial bunched xlpe cable 3x50 ( ph ) + 1x35 ( bare messenger cum neutral ) + 1x16 ( insulated street lighting ) sqmm 390 aerial bunched xlpe cable 3x95 ( ph ) + 1x70 ( bare messenger cum neutral ) + 1x16 ( insulated street lighting ) sqmm 391 lt pole clamp ( 50x8mm ) ( 2.56 kg ) with nut and bolts 392 lt eye hook 393 suspension clamp 394 dead end clamp 395 insulation piercing connectors / connector type i ( ab cable to ab cable ) 396 insulation piercing connectors type ii ( ab cable to service cable ) 397 end cap for ab cable 25 sqmm 398 end cap for ab cable 50 sqmm 399 end cap for ab cable 95 sqmm 400 feeder bifurcation ( 33kv line ) 401 overhead 33 kv new feeder 402 route survey and pole spotting and mapping ( as per employer requirement of sbd ) 403 9 meter long / 400 kg pcc poles ( pcc pole as per state practice ) 404 foundation of pcc supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.268 cmt for each support ) 405 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 406 13 m long steel tubular poles with welded steel base plate of designation 410 sp 72 407 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 408 stone pad for supports as per scope of works & drawing ( 450x450x75 mm ) 409 red oxide paint as per ts 410 aluminium paint as per ts 411 v type cross arm ( ms channel 100x50x6 mm 1980 mm long ) welded with ms angel ( 65x65x6 mm 935 mm long ) with bolts and nuts 412 cross arm holding clamps ( ms flat 65x8 mm ) with bolts and nuts 413 f bracket ( ms channel 100x50x6 mm ( 475 mm long ) welded with ms angle 75x75x6 mm ( 75 mm long ) with bolts and nuts 414 dp top channel ( channel 100x50x6mm ) 2240 mm longwith bolts and nuts 415 horizontal belting angle ( angle 65x65x6 mm ) 2240 mm long with bolts and nuts 416 cross bracing angle ( angle 65x65x6 mm ) 2500 mm long with bolts and nuts 417 bracing clamp top clamp ( flat 65x8 mm ) with bolts and nuts 418 bracing clamp bottom clamp ( flat 65x8 mm ) with bolts and nuts 419 fish plate for jumpering 420 6 / 4.72 mm+7 / 1.57 mm ( 100 mm² al. area ) acsr dog conductor 421 30 / 3.00 + 7 / 3.00 mm ( 200 sqmm al.area ) acsr panther conductor 422 pg clamp for dog conductor 423 pg clamp for panther conductor 424 armoured rod with ferrule 425 jointing sleeves aluminium 426 aluminium binding wire and tape 427 33 kv polymer disc insulator 70 kn ( b&s type ) along with suitable hardware fittings 428 33 kv polymer pin insulators 10 kn with nuts 429 earthing of pole by earthing coil ( with salt & charcoal ) 430 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 431 ms danger board with back calmps & nuts and boltsas per technical specification 432 anti climbing device 3.5 kgs, 2.5mm dia ( 12 swg ) galvanized barbed wire on each 11 kv support as per scope of works &ts 433 numbering of pole of each support as per technical specification and scope of work 434 underground 33 kv new feeder 435 radar route survey for route profile of any utility cables, pipes etc. along the route as per ts and scope of work 436 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 437 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 438 red oxide paint as per ts 439 aluminium paint as per ts 440 dp top channel ( channel 100x50x6mm ) 2240 mm longwith bolts and nuts 441 horizontal belting angle ( angle 65x65x6 mm ) 2240 mm long with bolts and nuts 442 cross bracing angle ( angle 65x65x6 mm ) 2500 mm long with bolts and nuts 443 bracing clamp top clamp ( flat 65x8 mm ) with bolts and nuts 444 bracing clamp bottom clamp ( flat 65x8 mm ) with bolts and nuts 445 fish plate for jumpering 446 33 kv polymer pin insulators 10 kn with nuts 447 heat shrinkable jointing kit indoor for 33 kv 3×300 sq.mm. xlpe cable 448 heat shrinkable jointing kit outdoor for 33 kv 3×300 sq.mm. xlpe cable 449 heat shrinkable cable jointing kit straight through for 33 kv 3×300 sq.mm. xlpe cable 450 road restoration chages for pucca road crossing 451 road restoration chages for kucchha road crossing 452 supply and placing of pre cast concrete manhole chambers of size 900mm x 900mm internal dimension x 800mm height & 100mm wall thickness ( heavy duty ) with concrete cover of 100mm thickness in the specified locations in the trench. 453 supply & erection of 33 kv single core 120 sqmm xlpe aluminium cable for jumpering 454 supply & erection of aluminum lugs 300 sq.mm. 455 supply & erection of cable warning tape 456 fixing of cable marker on cable route and inscription of feeder name and voltage on cable marker 457 supply of 33 kv 3×300 sqmm xlpe cable 458 earth digging, laying, termination / jointing, erection, testing & commissioning of 33 kv grade 3 core 300 sqmm xlpe power cable underground and backfilling with bricks, sands, excavated soil as per standard practise, levelling etc complete in all respect along with all accessories, earthing etc. and as per ts / approved drawing. 459 laying of 3x300 sq mm xlpe singlecableby digging of trench 1100 mm, deep, 750 mm wide its boxing with brick, sand, stone slabafter laying of cable separation of cable by brick wall up to stone slab filling and proper levelling& ramming. the ferruling of cable also include in this work ( all the material 460 laying of 3x300 sq mm xlpe twin cableby digging of trench 1100 mm deep, 750 mm wide its boxing with brick, sand, stone slab after laying of cable separation of cable by brick wall up to stone slab filling and proper levelling & ramming. the ferruling of cable also include in this work ( all the material 461 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection, testing & commissioning of 33 kv grade 3 core 300 sqmm xlpe power cable undergroundusing hdpe pipecomplete in all respect along with all accessories, earthing etc. and as per ts / approved drawing . 462 cable laying charges 463 pipe ( hdpe 160 mm dia ) for cable laying 464 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection, testing & commissioning of 33 kv grade 3 core 300 sqmm xlpe power cable undergroundwithout hdpe pipes in all respect along with all accessories, earthing etc. and as per ts / approved drawing . 465 cable laying charges 466 hoisting of following sizes of33 kv single cable on existing / erected double pole including gi pipe 3 mtr long 6 dia including jumpering, dressing of cable with required all necessary clamps and nut, bolts. ( all the material shall be arranged by contractor ) 467 testing & commissioning of 33 kv 3 core 300 sqmm xlpe power underground cable 468 earthing of pole by earthing coil ( with salt & charcoal ) 469 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 470 ms danger board with back calmps & nuts and boltsas per technical specification 471 anti climbing device 3.5 kgs, 2.5mm dia ( 12 swg ) galvanized barbed wire on each 11 kv support as per scope of works &ts 472 numbering of pole of each support as per technical specification and scope of work 473 feeder bifurcation ( 11kv line ) 474 overhead 11 kv new feeder 475 route survey and pole spotting and mapping ( as per employer requirement of sbd ) 476 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 477 foundation of pcc supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.268 cmt for each support ) 478 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 479 13 m long steel tubular poles with welded steel base plate of designation 410 sp 72 480 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 481 stone pad for supports as per scope of works & drawing ( 300x300x75 mm ) 482 red oxide paint as per ts 483 aluminium paint as per ts 484 11kv v type cross arm ( m.s channel 75x40x6mm ) welded with ms angel ( 50x50x6 ) ( weight 10.37 kg ) with bolts and nuts 485 cross arm holding clamps ( ms flat 50x8 mm ) ( weight 1.33 kg ) with bolts and nuts 486 f bracket ms flat ( 50x8 mm ) ( weight 1.56 kg ) with nut and bolts 487 cut point top channel ( 100x50x6 mm ) of length 230 mm along with nut & bolts 488 cut point bottom channel ( 100x50x6 mm ) of length 1150 mm along with nut & bolts 489 tapping horizontal cross arm ( 100x50x6 mm ) of length 1020 mm along with calmps ( 50x8 ) and nut and bolts 490 tapping top channel ( 100x50x6 mm ) of length 256 mm along with calmps ( 50x8 ) and nut and bolts 491 dp top channel ( channel 100x50x6mm ) 2240 mm longwith bolts and nuts 492 horizontal belting angle ( angle 50x50x6 mm ) 2240 mm long with bolts and nuts 493 cross bracing angle ( angle 50x50x6 mm ) 2500 mm long with bolts and nuts 494 belting clamp top clamp ( flat 50x8 mm ) ( weight 1.4 kg ) with bolts and nuts 495 belting clamp bottom clamp ( flat 50x8 mm ) ( weight 1.5 kg ) with bolts and nuts 496 fish plate for jumpering 497 6 / 2.59 + 1 / 2.59 mm ( 30 sqmm al. area ) acsr weasel conductors 498 6 / 3.35 + 1 / 3.35 mm ( 50 sqmm al. area ) acsr rabbit conductors 499 6 / 4.72 mm+7 / 1.57 mm ( 100 mm² al. area ) acsr dog conductor 500 pg clamp for weasel conductor 501 pg clamp for rabbit conductor 502 pg clamp for dog conductor 503 distribution tie for pin insulator 504 armoured rod with ferrule 505 jointing sleeves aluminium 506 aluminium binding wire and tape 507 11 kv polymer disc insulator 45 kn ( b&s type ) along with suitable hardware fittings 508 11 kv polymer pin insulators 5 kn with nuts 509 11 kv 3c×185 sqmm xlpe cable 510 heat shrinkable jointing kit outdoor for 11 kv 3c×185 sq.mm. xlpe cable 511 heat shrinkable cable jointing kit straight through for 11 kv 3c×185 sq.mm. xlpe cable 512 hoisting of following sizes of11 kv single cable on existing / erected double pole including gi pipe 3 mtr long 6 dia including jumpering, dressing of cable with required all necessary clamps and nut, bolts. ( all the material shall be arranged by contractor ) 513 earthing of pole by earthing coil ( with salt & charcoal ) 514 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 515 ms danger board with back calmps & nuts and boltsas per technical specification 516 anti climbing device 3.5 kgs, 2.5mm dia ( 12 swg ) galvanized barbed wire on each 11 kv support as per scope of works &ts 517 numbering of pole of each support as per technical specification and scope of work 518 underground 11 kv new feeder 519 radar route survey for route profile of any utility cables, pipes etc. along the route as per ts and scope of work 520 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 521 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 522 red oxide paint as per ts 523 aluminium paint as per ts 524 dp top channel ( channel 100x50x6mm ) 2240 mm longwith bolts and nuts 525 horizontal belting angle ( angle 50x50x6 mm ) 2240 mm long with bolts and nuts 526 cross bracing angle ( angle 50x50x6 mm ) 2500 mm long with bolts and nuts 527 belting clamp top clamp ( flat 50x8 mm ) ( weight 1.4 kg ) with bolts and nuts 528 belting clamp bottom clamp ( flat 50x8 mm ) ( weight 1.5 kg ) with bolts and nuts 529 fish plate for jumpering 530 11 kv polymer pin insulators 5 kn with nuts 531 heat shrinkable jointing kit indoor for 11 kv 3c×185 sq.mm. xlpe cable 532 heat shrinkable jointing kit indoor for 11 kv 3×300 sq.mm. xlpe cable 533 heat shrinkable jointing kit outdoor for 11 kv 3c×185 sq.mm. xlpe cable 534 heat shrinkable jointing kit outdoor for 11 kv 3×300 sq.mm. xlpe cable 535 heat shrinkable cable jointing kit straight through for 11 kv 3c×185 sq.mm. xlpe cable 536 heat shrinkable cable jointing kit straight through for 11 kv 3×300 sq.mm. xlpe cable 537 road restoration chages for pucca road crossing 538 road restoration chages for kucchha road crossing 539 supply and placing of pre cast concrete manhole chambers of size 900mm x 900mm internal dimension x 800mm height & 100mm wall thickness ( heavy duty ) with concrete cover of 100mm thickness in the specified locations in the trench. 540 supply & erection of 11 kv single core 95 sqmm xlpe aluminium cable for jumpering 541 supply & erection of aluminum lugs 185 sq.mm. 542 supply & erection of aluminum lugs 300 sq.mm. 543 supply & erection of cable warning tape 544 fixing of cable marker on cable route and inscription of feeder name and voltage on cable marker 545 supply of 11 kv 3c×185 sqmm xlpe cable 546 supply of 11 kv 3×300 sqmm xlpe cable 547 earth digging, laying, termination / jointing, erection, testing & commissioning of 11 kv grade 3 core 185 / 300 sqmm xlpe power cable underground and backfilling with bricks, sands, excavated soil as per standard practise, levelling etc complete in all respect along with all accessories, earthing etc. and as per ts / approved drawing. 548 laying of 11 kv 3cx185 sq mm xlpe singlecableby digging of trench 1100 mm, deep, 750 mm wide its boxing with brick, sand, stone slabafter laying of cable separation of cable by brick wall up to stone slab filling and proper levelling& ramming. the ferruling of cable also include in this work ( all the material 549 laying of 11 kv 3x185 sq mm xlpe twin cableby digging of trench 1100 mm deep, 750 mm wide its boxing with brick, sand, stone slab after laying of cable separation of cable by brick wall up to stone slab filling and proper levelling & ramming. the ferruling of cable also include in this work ( all the material ) 550 laying of 3x300 sq mm xlpe singlecableby digging of trench 1100 mm, deep, 750 mm wide its boxing with brick, sand, stone slabafter laying of cable separation of cable by brick wall up to stone slab filling and proper levelling& ramming. the ferruling of cable also include in this work ( all the material 551 laying of 3x300 sq mm xlpe twin cableby digging of trench 1100 mm deep, 750 mm wide its boxing with brick, sand, stone slab after laying of cable separation of cable by brick wall up to stone slab filling and proper levelling & ramming. the ferruling of cable also include in this work ( all the material 552 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection, testing & commissioning of 11 kv grade 3 core 185 / 300 sqmm xlpe power cable undergroundusing hdpe pipecomplete in all respect along with all accessories, earthing etc. and as per ts / approved drawing . 553 laying of 11 kv 3c×185 sqmm xlpe cable 554 laying of 11 kv 3×300 sqmm xlpe cable 555 pipe ( hdpe 160 mm dia ) for cable laying 556 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection, testing & commissioning of 11 kv grade 3 core 185 / 300 sqmm xlpe power cable undergroundwithout hdpe pipes in all respect along with all accessories, earthing etc. and as per ts / approved drawing. 557 laying of 11 kv 3c×185 sqmm xlpe cable 558 laying of 11 kv 3×300 sqmm xlpe cable 559 hoisting of following sizes of11 kv single cable on existing / erected double pole including gi pipe 3 mtr long 6 dia including jumpering, dressing of cable with required all necessary clamps and nut, bolts. ( all the material shall be arranged by contractor ) 560 testing & commissioning of 11 kv grade 3 core 185 sqmm xlpe power underground cable 561 testing & commissioning of 11 kv 3 core 300 sqmm xlpe power underground cable 562 earthing of pole by earthing coil ( with salt & charcoal ) 563 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 564 ms danger board with back calmps & nuts and boltsas per technical specification 565 anti climbing device 3.5 kgs, 2.5mm dia ( 12 swg ) galvanized barbed wire on each 11 kv support as per scope of works &ts 566 numbering of pole of each support as per technical specification and scope of work 567 augumentation / reconductoring of 33kv line 568 overhead 33 kv augumentation / reconductoring 569 route survey and pole spotting and mapping ( as per employer requirement of sbd ) 570 9 meter long / 400 kg pcc poles ( pcc pole as per state practice ) 571 foundation of pcc supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.268 cmt for each support ) 572 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 573 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 574 stone pad for supports as per scope of works & drawing ( 450x450x75 mm ) 575 red oxide paint as per ts 576 aluminium paint as per ts 577 v type cross arm ( ms channel 100x50x6 mm 1980 mm long ) welded with ms angel ( 65x65x6 mm 935 mm long ) with bolts and nuts 578 cross arm holding clamps ( ms flat 65x8 mm ) with bolts and nuts 579 f bracket ( ms channel 100x50x6 mm ( 475 mm long ) welded with ms angle 75x75x6 mm ( 75 mm long ) with bolts and nuts 580 dp top channel ( channel 100x50x6mm ) 2240 mm longwith bolts and nuts 581 horizontal belting angle ( angle 65x65x6 mm ) 2240 mm long with bolts and nuts 582 cross bracing angle ( angle 65x65x6 mm ) 2500 mm long with bolts and nuts 583 bracing clamp top clamp ( flat 65x8 mm ) with bolts and nuts 584 bracing clamp bottom clamp ( flat 65x8 mm ) with bolts and nuts 585 fish plate for jumpering 586 6 / 4.72 mm+7 / 1.57 mm ( 100 mm² al. area ) acsr dog conductor 587 30 / 3.00 + 7 / 3.00 mm ( 200 sqmm al.area ) acsr panther conductor 588 pg clamp for dog conductor 589 pg clamp for panther conductor 590 armoured rod with ferrule 591 jointing sleeves aluminium 592 aluminium binding wire and tape 593 33 kv polymer disc insulator 70 kn ( b&s type ) along with suitable hardware fittings 594 33 kv polymer pin insulators 10 kn with nuts 595 earthing of pole by earthing coil ( with salt & charcoal ) 596 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 597 ms danger board with back calmps & nuts and boltsas per technical specification 598 anti climbing device 3.5 kgs, 2.5mm dia ( 12 swg ) galvanized barbed wire on each 11 kv support as per scope of works &ts 599 numbering of pole of each support as per technical specification and scope of work 600 removal of existing material and shifting to mvvnl store 601 underground 33 kv augumentation / reconductoring 602 radar route survey for route profile of any utility cables, pipes etc. along the route as per ts and scope of work 603 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 604 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 605 red oxide paint as per ts 606 aluminium paint as per ts 607 dp top channel ( channel 100x50x6mm ) 2240 mm longwith bolts and nuts 608 horizontal belting angle ( angle 65x65x6 mm ) 2240 mm long with bolts and nuts 609 cross bracing angle ( angle 65x65x6 mm ) 2500 mm long with bolts and nuts 610 bracing clamp top clamp ( flat 65x8 mm ) with bolts and nuts 611 bracing clamp bottom clamp ( flat 65x8 mm ) with bolts and nuts 612 fish plate for jumpering 613 33 kv polymer pin insulators 10 kn with nuts 614 heat shrinkable jointing kit indoor for 33 kv 3×300 sq.mm. xlpe cable 615 heat shrinkable jointing kit outdoor for 33 kv 3×300 sq.mm. xlpe cable 616 heat shrinkable cable jointing kit straight through for 33 kv 3×300 sq.mm. xlpe cable 617 road restoration chages for pucca road crossing 618 road restoration chages for kucchha road crossing 619 supply and placing of pre cast concrete manhole chambers of size 900mm x 900mm internal dimension x 800mm height & 100mm wall thickness ( heavy duty ) with concrete cover of 100mm thickness in the specified locations in the trench. 620 supply & erection of 33 kv single core 120 sqmm xlpe aluminium cable for jumpering 621 supply & erection of aluminum lugs 300 sq.mm. 622 supply & erection of cable warning tape 623 fixing of cable marker on cable route and inscription of feeder name and voltage on cable marker 624 supply 33 kv 3×300 sqmm xlpe cable 625 earth digging, laying, termination / jointing, erection, testing & commissioning of 33 kv grade 3 core 300 sqmm xlpe power cable underground and backfilling with bricks, sands, excavated soil as per standard practise, levelling etc complete in all respect along with all accessories, earthing etc. and as per ts / approved drawing. 626 laying of 3x300 sq mm xlpe singlecableby digging of trench 1100 mm, deep, 750 mm wide its boxing with brick, sand, stone slabafter laying of cable separation of cable by brick wall up to stone slab filling and proper levelling& ramming. the ferruling of cable also include in this work ( all the material 627 laying of 3x300 sq mm xlpe twin cableby digging of trench 1100 mm deep, 750 mm wide its boxing with brick, sand, stone slab after laying of cable separation of cable by brick wall up to stone slab filling and proper levelling & ramming. the ferruling of cable also include in this work ( all the material 628 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection, testing & commissioning of 33 kv grade 3 core 300 sqmm xlpe power cable undergroundusing hdpe pipecomplete in all respect along with all accessories, earthing etc. and as per ts / approved drawing . 629 laying of 33 kv 3×300 sqmm xlpe cable 630 pipe ( hdpe 160 mm dia ) for cable laying 631 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection, testing & commissioning of 33 kv grade 3 core 300 sqmm xlpe power cable undergroundwithout hdpe pipes in all respect along with all accessories, earthing etc. and as per ts / approved drawing. 632 laying of 33 kv 3×300 sqmm xlpe cable 633 hoisting of following sizes of33 kv single cable on existing / erected double pole including gi pipe 3 mtr long 6 dia including jumpering, dressing of cable with required all necessary clamps and nut, bolts. ( all the material shall be arranged by contractor ) 634 testing & commissioning of 33 kv 3 core 300 sqmm xlpe power underground cable 635 earthing of pole by earthing coil ( with salt & charcoal ) 636 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 637 ms danger board with back calmps & nuts and boltsas per technical specification 638 anti climbing device 3.5 kgs, 2.5mm dia ( 12 swg ) galvanized barbed wire on each 11 kv support as per scope of works &ts 639 numbering of pole of each support as per technical specification and scope of work 640 removal of existing material and shifting to mvvnl store 641 augumentation / reconductoring of 11kv line 642 overhead 11 kv augumentation / reconductoring 643 route survey and pole spotting and mapping ( as per employer requirement of sbd ) 644 8.5 m / 180 kgs pcc poles ( pcc pole as per state practice ) 645 foundation of pcc supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.268 cmt for each support ) 646 stone pad for supports as per scope of works & drawing ( 300x300x75 mm ) 647 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 648 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 649 red oxide paint as per ts 650 aluminium paint as per ts 651 11kv v type cross arm ( m.s channel 75x40x6mm ) welded with ms angel ( 50x50x6 ) ( weight 10.37 kg ) with bolts and nuts 652 cross arm holding clamps ( ms flat 50x8 mm ) ( weight 1.33 kg ) with bolts and nuts 653 f bracket ms flat ( 50x8 mm ) ( weight 1.56 kg ) with nut and bolts 654 cut point top channel ( 100x50x6 mm ) of length 230 mm along with nut & bolts 655 cut point bottom channel ( 100x50x6 mm ) of length 1150 mm along with nut & bolts 656 tapping horizontal cross arm ( 100x50x6 mm ) of length 1020 mm along with calmps ( 50x8 ) and nut and bolts 657 tapping top channel ( 100x50x6 mm ) of length 256 mm along with calmps ( 50x8 ) and nut and bolts 658 dp top channel ( channel 100x50x6mm ) 2240 mm longwith bolts and nuts 659 horizontal belting angle ( angle 50x50x6 mm ) 2240 mm long with bolts and nuts 660 cross bracing angle ( angle 50x50x6 mm ) 2500 mm long with bolts and nuts 661 belting clamp top clamp ( flat 50x8 mm ) ( weight 1.4 kg ) with bolts and nuts 662 belting clamp bottom clamp ( flat 50x8 mm ) ( weight 1.5 kg ) with bolts and nuts 663 fish plate for jumpering 664 6 / 2.59 + 1 / 2.59 mm ( 30 sqmm al. area ) acsr weasel conductors 665 6 / 3.35 + 1 / 3.35 mm ( 50 sqmm al. area ) acsr rabbit conductors 666 6 / 4.72 mm+7 / 1.57 mm ( 100 mm² al. area ) acsr dog conductor 667 pg clamp for weasel conductor 668 pg clamp for rabbit conductor 669 pg clamp for dog conductor 670 distribution tie for pin insulator 671 armoured rod with ferrule 672 jointing sleeves aluminium 673 aluminium binding wire and tape 674 11 kv polymer disc insulator 45 kn ( b&s type ) along with suitable hardware fittings 675 11 kv polymer pin insulators 5 kn with nuts 676 earthing of pole by earthing coil ( with salt & charcoal ) 677 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 678 ms danger board with back calmps & nuts and boltsas per technical specification 679 anti climbing device 3.5 kgs, 2.5mm dia ( 12 swg ) galvanized barbed wire on each 11 kv support as per scope of works &ts 680 numbering of pole of each support as per technical specification and scope of work 681 removal of existing material and shifting to mvvnl store 682 underground 11 kv augumentation / reconductoring 683 radar route survey for route profile of any utility cables, pipes etc. along the route as per ts and scope of work 684 11 m long steel tubular poles with welded steel base plate of designation 410 sp 55 685 foundation of stp supports as per scope of works, cement concreting ( 1:2:4 ) ( 0.5 cmt for each support & .014 cmt. for muffing ) 686 red oxide paint as per ts 687 aluminium paint as per ts 688 dp top channel ( channel 100x50x6mm ) 2240 mm longwith bolts and nuts 689 horizontal belting angle ( angle 50x50x6 mm ) 2240 mm long with bolts and nuts 690 cross bracing angle ( angle 50x50x6 mm ) 2500 mm long with bolts and nuts 691 belting clamp top clamp ( flat 50x8 mm ) ( weight 1.4 kg ) with bolts and nuts 692 belting clamp bottom clamp ( flat 50x8 mm ) ( weight 1.5 kg ) with bolts and nuts 693 fish plate for jumpering 694 11 kv polymer pin insulators 5 kn with nuts 695 heat shrinkable jointing kit indoor for 11 kv 3c×185 sq.mm. xlpe cable 696 heat shrinkable jointing kit indoor for 11 kv 3×300 sq.mm. xlpe cable 697 heat shrinkable jointing kit outdoor for 11 kv 3c×185 sq.mm. xlpe cable 698 heat shrinkable jointing kit outdoor for 11 kv 3×300 sq.mm. xlpe cable 699 heat shrinkable cable jointing kit straight through for 11 kv 3c×185 sq.mm. xlpe cable 700 heat shrinkable cable jointing kit straight through for 11 kv 3×300 sq.mm. xlpe cable 701 road restoration chages for pucca road crossing 702 road restoration chages for kucchha road crossing 703 supply and placing of pre cast concrete manhole chambers of size 900mm x 900mm internal dimension x 800mm height & 100mm wall thickness ( heavy duty ) with concrete cover of 100mm thickness in the specified locations in the trench. 704 supply & erection of 11 kv single core 95 sqmm xlpe aluminium cable for jumpering 705 supply & erection of aluminum lugs 185 sq.mm. 706 supply & erection of aluminum lugs 300 sq.mm. 707 supply & erection of cable warning tape 708 fixing of cable marker on cable route and inscription of feeder name and voltage on cable marker 709 supply of 11 kv 3c×185 sqmm xlpe cable 710 supply of 11 kv 3×300 sqmm xlpe cable 711 earth digging, laying, termination / jointing, erection, testing & commissioning of 11 kv grade 3 core 185 / 300 sqmm xlpe power cable underground and backfilling with bricks, sands, excavated soil as per standard practise, levelling etc complete in all respect along with all accessories, earthing etc. and as per ts / approved drawing. 712 laying of 11 kv 3cx185 sq mm xlpe singlecableby digging of trench 1100 mm, deep, 750 mm wide its boxing with brick, sand, stone slabafter laying of cable separation of cable by brick wall up to stone slab filling and proper levelling& ramming. the ferruling of cable also include in this work ( all the material 713 laying of 11 kv 3x185 sq mm xlpe twin cableby digging of trench 1100 mm deep, 750 mm wide its boxing with brick, sand, stone slab after laying of cable separation of cable by brick wall up to stone slab filling and proper levelling & ramming. the ferruling of cable also include in this work ( all the material ) 714 laying of 3x300 sq mm xlpe singlecableby digging of trench 1100 mm, deep, 750 mm wide its boxing with brick, sand, stone slabafter laying of cable separation of cable by brick wall up to stone slab filling and proper levelling& ramming. the ferruling of cable also include in this work ( all the material 715 laying of 3x300 sq mm xlpe twin cableby digging of trench 1100 mm deep, 750 mm wide its boxing with brick, sand, stone slab after laying of cable separation of cable by brick wall up to stone slab filling and proper levelling & ramming. the ferruling of cable also include in this work ( all the material 716 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection, testing & commissioning of 11 kv grade 3 core 185 / 300 sqmm xlpe power cable undergroundusing hdpe pipecomplete in all respect along with all accessories, earthing etc. and as per ts / approved drawing . 717 laying of 11 kv 3c×185 sqmm xlpe cable 718 laying of 11 kv 3×300 sqmm xlpe cable 719 pipe ( hdpe 160 mm dia ) for cable laying 720 earth digging by horizontal directional drilling ( hdd ) method, laying, termination / jointing, erection, testing & commissioning of 11 kv grade 3 core 185 / 300 sqmm xlpe power cable undergroundwithout hdpe pipes in all respect along with all accessories, earthing etc. and as per ts / approved drawing . 721 laying of 11 kv 3c×185 sqmm xlpe cable 722 laying of 11 kv 3×300 sqmm xlpe cable 723 hoisting of following sizes of11 kv single cable on existing / erected double pole including gi pipe 3 mtr long 6 dia including jumpering, dressing of cable with required all necessary clamps and nut, bolts. ( all the material shall be arranged by contractor ) 724 testing & commissioning of 11 kv grade 3 core 185 sqmm xlpe power underground cable 725 testing & commissioning of 11 kv 3 core 300 sqmm xlpe power underground cable 726 earthing of pole by earthing coil ( with salt & charcoal ) 727 8 swg gi wire for pole, db earthingwith gi nuts, bolts & washers 728 ms danger board with back calmps & nuts and boltsas per technical specification 729 anti climbing device 3.5 kgs, 2.5mm dia ( 12 swg ) galvanized barbed wire on each 11 kv support as per scope of works &ts 730 numbering of pole of each support as per technical specification and scope of work 731 removal of existing material and shifting to mvvnl store 732 lt line with underground cabling 733 radar route survey for route profile of any utility cables, pipes etc. along the route as per ts and scope of work 734 supply & laying of lt aluminium xlpe cable 1cx630 sq.mm. 735 supply & laying of lt aluminium xlpe cable 1cx400 sq.mm. 736 supply of 1100 v grade, pvc sheathed steel strip armoured, aluminum conductor lt xlpe insulated cable of 3.5cx70 sqmm 737 supply of 1100 v grade, pvc sheathed steel strip armoured, aluminum conductor lt xlpe insulated cable of 3.5cx150 sqmm 738 supply of 1100 v grade, pvc sheathed steel strip armoured, aluminum conductor lt xlpe insulated cable of 3.5cx240 sqmm 739 laying of 1100 v grade 3.5cx70 sqmm, pvc sheathed steel strip armoured, aluminum conductor lt xlpe insulated cable to be laid underground in trenches. 740 laying of 1100 v grade 3.5cx150 sqmm, pvc sheathed steel strip armoured, aluminum conductor lt xlpe insulated cable to be laid underground in trenches. 741 laying of 1100 v grade 3.5cx240 sqmm, pvc sheathed steel strip armoured, aluminum conductor lt xlpe insulated cable to be laid underground in trenches. 742 laying of 1100 v grade 3.5cx70 sqmm by horizontal directional drilling ( hdd ) method, pvc sheathed steel strip armoured, aluminum conductor lt xlpe insulated cable to be laid underground in hdpe pipe. 743 laying of 1100 v grade 3.5cx150 sqmm by horizontal directional drilling ( hdd ) method, pvc sheathed steel strip armoured, aluminum conductor lt xlpe insulated cable to be laid underground in hdpe pipe. 744 laying of 1100 v grade 3.5cx240 sqmm by horizontal directional drilling ( hdd ) method, pvc sheathed steel strip armoured, aluminum conductor lt xlpe insulated cable to be laid underground in hdpe pipe. 745 cable end termination using total double compression brass glands and crimping type aluminium thimbles for 3.5cx70 sqmm 746 cable end termination using total double compression brass glands and crimping type aluminium thimbles for 3.5cx150 sqmm 747 cable end termination using total double compression brass glands and crimping type aluminium thimbles for 3.5cx240 sqmm 748 digging of trench by excavation of earth, laying of bricks to cover the cable and filling of sand & earth ramming and dressing properly with complete job for laying of 1100 v grade, pvc sheathed steel strip armoured, aluminum conductor lt xlpe insulated cables. 749 back fillng & restoring the road to make it as original including supply of all material. 750 supply & laying of hdpe pipe of following size by horizontal drilling for underground piping ( trenchless ) for above cable at road crossings. min depth of pipe shall be 1.2 m below surface. 751 160 mm dia 752 110 mm dia 753 50 mm dia 754 supply and marking of manhole 750x600 mm with manhole cover for pullinglt cable in lanes by lanes 755 supply , installation and testing of 7x20 swg gi wire for earthing along cables. 756 supply and laying of pipe for service cable to houses. 757 gl pipe of 50 mm dia ( external area ) 758 gl pipe of 40 mm dia ( external area ) 759 pvc pipe heavy gauge 50 mm dia ( underground area ) 760 pvc pipe heavy gauge 40 mm dia ( underground area ) 761 supply and installation of rcc pipe of folloing size: 762 150 mm 763 200 mm 764 300 mm 765 supply and installation of 8 swg earthing gi wire 766 supply and making steel structure work and painting the same with two coats of primer and two coats of enamel paint. 767 supply and laying ( in gi pipe ) of 1100 v grade, pvc sheathed steel strip armoured, aluminum conductor lt xlpe insulated cable of size 2x10 sq.mm. xlpe ( for street light ) 768 supply & laying of gl pipe of 40 mm dia. underground 769 supply & installation of junction box on stp with 900 mm long gi pipe 25 mm dia. with clamps for street light connection. 770 supply and erection of earthing 40 mm dia 15 m. long g.i.pipe vertically for earthing having 12mm dia holes spaced 75 mm apart drilled up to 2m from the bottom all complete as per specification 771 fixing of gi strip of following sizes with hardware, mounting clamps etc.: 772 25 x 3 mm. gi strip 773 32 x 6 mm. gi strip 774 50 x 6 mm. gi strip 775 dismantling of lt overhead line and transportation of dismantled material to mvvnl stores. 776 supply of outdoor type lt distribution box with a rupturing capacity of 50 ka at 415 volt called for individual items ( cpri approved manufacturer ) openable in front & back suitable for 3 phase, four wire, 50 hz ac supply & an ambient temperature of 45 deg. c. the cubical should be weather proof, dust proof, vermin proof and in closer protection shall be ip 54 ( suitable for outdoor applications ) as per is 2147 1962 and is 8623 the panels & switches boards shall be fabricated out of 14 swg crca sheet steel & provided with 16swg hinged door including suitable foundation, main lt panel at substation 1000 & 630 kva ( type a 1 ) incomer 1 no. 1250 amp. tp mdo acb with inbuilt mpr released with ( on / off indicating light ) ( metering on incomer 1 set of digital ammeter with ass ) ( 1 set of digital voltmeter with vss ) ( 1 set of led type phase indication light ( 22.5 mm ) with control mcbs ) ( outgoing 4 sets of 400 amp. tp mccb with spreader & extended handle ) ( 2 sets of 250amp. tp mccb with spreader & extended handle ) ( 2 sets of 100 0amp. tp mccb with spreader & extended handle ) 777 supply of outdoor type lt distribution box with a rupturing capacity of 50 ka at 415 volt called for individual items ( cpri approved manufacturer ) openable in front & back suitable for 3 phase, four wire, 50 hz ac supply & an ambient temperature of 45 deg. c. the cubicle should be weather proof, dust proof, vermin proof and in closer protection shall be ip 54 ( suitable for outdoor applications ) as per is 2147 1962 and is 8623 the panels & switches boards shall be fabricated out of 14 swg crca sheet steel & provided with 16swg hinged door including suitable foundation, main lt panel at substation 400 kva ( type a 2 ) ( incomer 1 set of 800 amp.tp mdo acb with inbuilt mpr released with ( on / off indicating light ) ( metering on incomer 1 set of digital ammeter with ass ) ( 1 set of digital voltmeter with vss ) ( 1 set of led type phase indication light ( 22.5 mm ) with control mcbs ) ( outgoing 6 sets of 250 amp. tp mccb with spreader & extended handle ( 5no.+1no. capacitor panel ) ) ( 2 sets of 100 amp. tp mccb with spreader & extended handle ) 778 supply of outdoor type lt distribution box with a rupturing capacity of 50 ka at 415 volt called for individual items ( cpri approved manufacturer ) openable in front & back suitable for 3 phase, four wire, 50 hz ac supply & an ambient temperature of 45 deg. c. the cubical should be weather proof, dust proof, vermin proof and in closer protection shall be ip 54 ( suitable for outdoor applications ) as per is 2147 1962 and is 8623 the panels & switches boards shall be fabricated out of 14 swg crca sheet steel & provided with 16swg hinged door including suitable foundation, main lt panel at substation 250 kva ( type a 3 ) ( incomer 1 set of 630 amp. tp mdo acb with inbuilt mpr released with ( on / off indicating light ) ( metering on incomer 1 set of digital ammeter with ass ) ( 1 set of digital voltmeter with vss ) ( 1 set of led type phase indication light ( 22.5 mm ) with control mcbs ) ) ( outgoing 5 sets of 250 amp. tp mccb with spreader & extended handle ( 4no.+1no. capacitor panel ) ) ( 2 sets of 100 amp. tp mccb with spreader & extended handle ) 779 supply of outdoor type lt distribution box with a rupturing capacity of 50 ka at 415 volt called for individual items ( cpri approved manufacturer ) openable in front & back suitable for 3 phase, four wire, 50 hz ac supply & an ambient temperature of 45 deg. c. the cubical should be weather proof, dust proof, vermin proof and in closer protection shall be ip 54 ( suitable for outdoor applications ) as per is 2147 1962 and is 8623 the panels & switches boards shall be fabricated out of 14 swg crca sheet steel & provided with 16swg hinged door including suitable foundation, main lt panel at substation 160 kva ( type a 4 ) ( incomer 1 set of 400 amp. tp mdo acb with inbuilt mpr released with ( on / off indicating light ) ( metering on incomer 1 set of digital ammeter with ass ) ( 1 set of digital voltmeter with vss ) ( 1 set of led type phase indication light ( 22.5 mm ) with control mcbs ) ( outgoing 4 sets of 250 amp. tp mccb with spreader & extended handle ( 3no.+1no. capacitor panel ) ) ( 2 sets of 100 amp. tp mccb with spreader & extended handle ) 780 supply of outdoor type lt disribution boards with a rupturing capacity of 50ka at 415v or as called for individual items ( cpri approved manufacturer ) , openable in front and back suitable for 3 plase, 4 wire, 50hz ac supply and an ambient temperature of 45 deg. c. the cubicle should be weather proof, dust proof, vermin proof and enclosure protection shall be ip 54 ( suitable for outdoor applications ) as per is 2147 1962 and is: 8623. the panels / switches boards shall be fabricated out of 14 swg crca sheet steel and provided with 16 swg hinged doors including suitable foundation. main lt panel at sub station 100kva ( type a 5 ) incomer 1 set of 250 amp. tp mccb with spreader & extended handlemetering on incomer 1 set of digital ammeter with ass 1 set of digital voltmeter with vss 1 set of led type phase indicating light ( 22.5 mm. ) with control mcbsoutgoing 3 set of 63 amp. tp mccb with spreader & extended handle ( 2 nos. + 1 no. for capacitor panel ) 3 set of100 amp. tp mccb with spreader & extended handle 781 supply of outdoor type lt disribution boards with a rupturing capacity of 50ka at 415v or as called for individual items ( cpri approved manufacturer ) , openable in front and back suitable for 3 plase, 4 wire, 50hz ac supply and an ambient temperature of 45 deg. c. the cubicle should be weather proof, dust proof, vermin proof and enclosure protection shall be ip 54 ( suitable for outdoor applications ) as per is 2147 1962 and is: 8623. the panels / switches boards shall be fabricated out of 14 swg crca sheet steel and provided with 16 swg hinged doors including suitable foundation. main lt panel at sub station 63 & 25kva ( type a 6 ) incomer 1 set of 160 amp. tp mccb with spreader & extended handlemetering on incomer 1 set of digital ammeter with ass 1 set of digital voltmeter with vss 1 set of led type phase indicating light ( 22.5 mm. ) with control mcbsoutgoing 4 set of 63 amp. tp mccb with spreader & extended handle 1 set of32 amp. tp mccb with spreader & extended handle ( for capacitor panel ) 782 supply , installation, testing & commissioning of outdoor type feeder pillar panel to be made of 2 mm crca sheet and covers will be 1.6mm crca sheet duly powder coated paint with 400 amps al. busbar. ( type b1 ) incomer 250 amp. tp mccb 1 no.outgoing 63 amp. tp mccb 6 nos. the cubicle should be weather proof, dust proof, vermin proof and enclosure protection shall be ip 54 ( suitable for outdoor applications ) as per is 2147 1962 and is: 8623. 783 supply , installation, testing & commissioning of outdoor type feeder pillar panel to be made of 2 mm crca sheet and covers will be 1.6mm crca sheet duly powder coated paint with 300 amps al. busbar. ( type b2 ) incomer 250 amp. tp mccb 1 no.outgoing 63 amp. tp mccb 5 nos. the cubicle should be weather proof, dust proof, vermin proof and enclosure protection shall be ip 54 ( suitable for outdoor applications ) as per is 2147 1962 and is: 8623. 784 supply , installation, testing & commissioning of outdoor type feeder pillar panel to be made of 2 mm crca sheet and covers will be 1.6mm crca sheet duly powder coated paint with 300 amps al. busbar. ( type b3 ) incomer 100 amp. tp mccb 1 no.outgoing 63 amp. tp mccb 4 nos. the cubicle should be weather proof, dust proof, vermin proof and enclosure protection shall be ip 54 ( suitable for outdoor applications ) as per is 2147 1962 and is: 8623. 785 supply , installation, testing & commissioning of lockable distribution boxes of size 450x400mm with bus bar 100 amp. tpn to feed upto 10 houses ( type c ) . the cubicle should be weather proof, dust proof, vermin proof and enclosure protection shall be ip 54 ( suitable for outdoor applications ) as per is 2147 1962 and is: 8623.the panels / switches boards shall be fabricated out of 14 swg crca sheet steel and provided with 16 swg hinged doors including suitable foundation 786 supply of steel structure of size 65x65x6 mm ( m.s. angle ) including supply of nut bolt and washres. 787 supply and laying of single phase ( 2cx4 sqmm ) xlpe armoured service cable 788 supply and laying of single phase ( 2cx6 sqmm ) xlpe armoured service cable 789 supply and laying of three phase ( 4cx16 sqmm ) xlpe armoured service cable 790 supply & installation of single coil earthing at type a, b and double coil earthing at type c panels 791 supply & erection of plinth for outdoor type lt disribution boards ( a type ) and distribution feeder pillar box ( b type ) 792 supply & erection of plinth for outdoor type lt disribution sevice pillar ( c type ) 793 supply & erection of single phase poly carbonate meter box after removal of existing meter box and connections of meters with armoured cable laid along with resealing of meter with seals provided by mvvnl 794 supply & erection of three phase poly carbonate meter box after removal of existing meter box and connections of meters with armoured cable laid along with resealing of meter with seals provided by mvvnl 795 testing & commissioning of 3.5 core 240 sqmm xlpe power underground cable 796 testing & commissioning of 3.5 core 150 sqmm xlpe power underground cable 797 testing & commissioning of 3.5 core 70 sqmm xlpe power underground cable 798 installation of capacitor bank 799 installation of capacitor bank at 33 / 11 kv power transformer 800 12.65 kv, 1980 kvar, 3 phase, 50 c / s, outdoor type , capacitor bank having two variable step of 792 kvar & one variable steps of 396 kvar. bank shall be complete with capacitor units of 264 / 132 kvar, aluminium busbars, pin & post insulators, expulsion fuses etc. 801 12.65 kv, 3960 kvar, 3 phase, 50 c / s, outdoor type, capacitor bank having two variable step of 792 kvar & two variable steps of 1188 kvar. bank shall be complete with capacitor units of264 / 396 kvar, aluminimum busbars, pin & post insulators, expulsion fuses etc. 802 0.79 kvar for 1188 kvar step 803 0.52 kvar for 792 kvar step 804 0.25 kvar for 396 kvar step 805 11 kv, 3 phase oil cooled rvt 806 12 kv 3 phase outdoor type metal enclosed vacuum capacitor switches. 807 11 kv, 400 amp, off load isolator with earth switch and mounting structure. 808 9 kv, 10 ka, station class, lightning arrestors 809 indoor type automatic control unit 810 hot dip galvanised structures for complete system 811 control cables, lugs / thimble, junction box etc. 812 11 kv xlpe insulated 3x120 mm2armoured 813 indoor temination kit 814 outdoor temination kit 815 11 kv vcb switchgear with complete arangement for connection with existing 11 kv bus bar. 816 casting of civil foundation 817 cable trench for laying of power / control cables. 818 earthing for structure and las by pipe in pipe earthing ( gi earthing pipe of 40 mm dia & 3000 mm long as per is 1161 ) 819 gi strip of size 50x6 mm for connection of earthing with equipment 820 installation of capacitor bank at 11 / 0.415 kv distribution transformer 821 lt pole cap gas / resin filled mpp ( metalized polypropylene ) shunt capacitors 440v, 10 kvar, 3 phase 50 hz, ip65 with fault indication. 822 lt pole cap gas / resin filled mpp ( metalized polypropylene ) shunt capacitors 440v, 25 kvar, 3 phase 50 hz, ip65 with fault indication. 823 lt pole cap gas / resin filled mpp ( metalized polypropylene ) shunt capacitors 440v, 40 kvar, 3 phase 50 hz, ip65 with fault indication. 824 suitable pole clamps with nuts and bolts 825 1cx25 sqmm xlpe cable along with connecting clamps for connection of dtr with capacitor bank 826 earthing of existing substation and distribution transformer 827 pipe earthing for substation ( 3000 mm long ) 828 spike earthing for existing dtr ( 2500mm long ) 829 installation of 11 kv horizontal isolator, ab switch and lt distribution boxfor distribution transformer 830 supply and erection of 11 kv horizontal isolator with complete allied materials 831 supply and erection of 11kv ab switch with complete allied materials 832 supply and erection of ltdb made out of crca ms for 63 kva dtr with all allied materials 833 supply and erection of ltdb made out of crca ms for 100 kva dtr with all allied materials 834 supply and erection of ltdb made out of crca ms for 250 kva dtr with all allied materials 835 supply and erection of ltdb made out of crca ms for 400 kva dtr with all allied materials 836 supply and erection of ltdb made out of crca ms for 630 kva dtr with all allied materials 837 supply and erection of ltdb made out of crca ms for 1000 kva dtr with all allied materials 838 miscellaneous items 839 11 kv weasel covered conductor with accessories 840 11 kv rabbit covered conductor with accessories 841 33 kv dog covered conductor with accessories 842 shear bolted tusker terminal connector on ht side 843 shear bolted tusker terminal connector on lt side 844 shear head bolted lugs ( 630 sqmm ) 845 shear head bolted lugs ( 400 sqmm ) 846 aluminium lug long barrel off size 847 ms nut & bolts 848 plinth of distribution transformer ( 215 kva to 630 kva ) with frp fencing 849 sign board of size 6x4 sqfeet, mounting angels, excavation, cement concreting, foundation, painting etc. 850 sign board of size 1x1 sqfeet with pole mounting clamp, painting etc. 851 stay set ( galvanised ) with 50x8 mm stay clamps, guy insulator , anchor plate ( 200x200x6mm ) , nut bolts, 1 nos turn buckle, 1.8 m long, 16 mm diameter solid gs stay rod & 7 / 3.15 mm dia gi strandedwire complete as per technical specification, approved drawings and scope of work including foundation of stay support in each stay set as per scope of works 852 stay rod 16x1800 mm complete as per technical specification, scope of work and tender drawing 853 stay wire 7 / 10 swg 854 stay clamp ( flat 50x8 mm ) ( weight 1.5 kg ) with bolts and nuts 855 stay guy insulator lt 856 stay guy insulator ht ( 11 kv ) 857 stay thimble 858 hellically formed end fitting 859 concreting of stay road ( 0.2 cmt cement concreting in mixture ( 1:2:4 ) 860 stay set ( galvanised ) with 50x8 mm stay clamps, guy insulator , anchor plate ( 300x300x8mm ) , nut bolts, 1 nos turn buckle, 1.8 m long, 20 mm diameter solid gs stay rod & 7 / 4.00 mm dia gi strandedwire complete as per technical specification, approved drawings and scope of work including foundation of stay support in each stay set as per scope of works 861 stay rod 20x1800 mm complete as per technical specification, scope of work and tender drawing 862 stay wire 7 / 8 swg 863 stay clamp ( flat 50x8 mm ) ( weight 1.8 kg ) with bolts and nuts 864 stay guy insulator for 33kv line 865 stay thimble 866 hellically formed end fitting 867 concreting of stay road ( 0.3 cmt cement concreting in mixture ( 1:2:4 ) ...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

33349587 construction of 33 kv line from 132 / 33 kv s / s awas vikasto 33 / 11 kv, s / s rajani khand, for providing independent 33 kv source to this substation 1 safe dragging, loading, carriage and unloading of following store materials with proper stacking from esc daliganj to je dump store and je dump store to work site within municipal areas. 2 33 kv 3x300sqmm xlpe cable 3 33 kv jointing kit 3x300 sq mm cable outdoor 4 33 kv jointing kit 3x300sq mm straight through 5 33 kv line isolator 6 33kvcurrent transformer 400 / 200 / 1 7 stp 11 m long 8 33 kv pin insulator 9 33 kv pin with nut 10 top / ms channel 100x50 mm10 kg / mtr 11 ms angle 65x65x6mm 5.8 kg / mtr 12 ms channel 125x65mm @13.1 kg. mtr. 13 ms angle 75x75x6 mm @6.8 kg. / mtr. 14 m s earthing rod 20x2500 mm 15 lt xlpe cable al.1x400 sq.mm. 16 digging of pit in kachcha / pakka land in depth upto 1 / 6 length of pole, dragging of stp from nearby place / dump, erection of single pole along with stone pad in bottom with proper alignment on 11 mtr long st pole and refilling with ramming of earth 17 grouting of pole in depth of 01 mtr. below ground level in ratio 1:4:8 in cement, sand and brick ballast as per respo norms. 18 construction of pole plinth 300mm x 450 mm above ground level in ratio 1:2:4 in cement, coarse sand and stone gritt as per respo norms. 19 painting of new erected st pole with two coat of red oxide paint, po red paint at top of pole 2 mtr and balance by two coats of best quality aluminium paint isi mark as per norms. 20 laying of d / c 33 kv 3x300 sqmm xlpe cable in parallel in normal soil bydigging of trench 1050 mm deep & 750 mm wide its boxing with bricks laying of cable & seperation of cable by brick wall, filling of sand upto top and covering with stone slab after laying of cable ( all material will be provided by contractor except 33 kv cable ) 21 laying of s / c 33 kv 3x300 sqmm xlpe cable in normal soil by digging of trench 1050 mm deep & 500 mm wide its boxing with bricks, laying of cable, filling of sand upto top and covering with stone slab after laying of cable ( all material will be provided by contractor except 33 kv cable ) 22 laying of 33 kv xlpe cable 3x300 sq mm s / c in ms pipe 150 mm dia by digging of trench in kachcha / pakka of suitable size at road crossing ( all material will be provided by contractor except 33 kv cable ) 23 laying of single 33 kv 3x300 sqmm xlpe cable by drill method 24 laying of single 33 kv 3x300 sqmm xlpe cable by drill method in hdpe pipe 150 mm dia ( all material will be provided by contractor except 33 kv cable ) . 25 laying of single 33 kv 3x300 sqmm xlpe cable by drill method in ms pipe 150 mm dia ( all material will be provided by contractor except 33 kv cable ) . 26 cable laying in already constructed trench / existing pipe s / c 27 fabrication & erection of 33 kv exposure type double polewith the provision of bus bar on 11 mtr. long st pole with fixing of necessary clamps & other accesories like 02 no. channel 100x50mm ( 1600 mm each ) , 02 no. bracing angle 65x65x6 mm ( 2800 mm each ) for supporting the hoisting of cable on pole, 09 no. pin insulator with pin, danger board, number platesand barbed wire etc. its jumpering by single core pvc al. cable with proper size of lug ( all required materials will be provided by contractor except st pole, steel parts, pin insulator with pin and pvc al. cable ) 28 hoisting of 33 kv 3x300 sqmm xlpe cable on d / p through gi pipe of size 6 dia 3 mtr long including its jumpering complete with holding clamps, pg clamps, nut & bolts ( all material will be provided by contractor ) 29 making of heat & shrinkables joints of following sizes and types in 33 kv xlpe cable ( jointing kit will be provided by deptt. ) 30 outdoor end termination kit for 33 kv 3x300 sqmm xlpe cable 31 straight through jointing kit for 33 kv 3x300 sqmm 32 digging of pit of size 3x2x1.2 mtr for making straight through joint of 33 kv cable size 3x300 sqmm work included boxing of pit by sand, brick and stone slab filling of soil levelling and ramming of the same. ( s / th provided by the deptt. ) 33 earthing of poles with ms earthing rod 20x2500 mm, earth wire with nut and bolts as per norms ( all material will be provided by contractor except ms earthing rods ) . 34 high pressure testing of 33 kv cable. testing equipment will be arranged by contractor. 35 fabrication & erection of cable stand made of two nos ms channel 100x50x3 mtr. long jointed to each other by means of 05 nos ms strip 50x6 mm of size 150 mm long each by welding at equal distance interval as per norms and grouting in block of 300x300x700 completely providing two nos cable clamp also. ( all materials will provide by contractor except ms channel ) . 36 isolator structure fabrication of isolator structure minimum 3.5 mtr overall height and 2.5 mtr above ground level as per resspo drawing, with help of m.s channel 125x65 mm two pieces of m.s channel joined to each other by m.s flat 50x6 mm, diagonally at the interval of 0.5 mtr and top & bottom of the structure. grouting of isolator structure in cc ( cement , coarse sand and stone grit of 20 mm gauge ) including supply of necessary t&p and painting of structure complete. ( only m.s channel and angle provided by the deptt ) 37 painting of all structures equipment ( new and existing ) . 38 mounting of accessories / equipment on fabricated structure complete work with making proper alignment and tightening the work including fabrication work if required for proper operation of equipment 39 33 kv current transformer 400 / 200 / 1 a 40 bus / line isolator 41 jumpering of complete line bay with acsr panther cond. with required clamp, nut & bolts from existing 33 kv bus bar & 33 kv cable complete work. ( required pg clamps will be provided by contractor ) . 42 laying of single circuit 33 kv 3x300 sq mm xlpe cable in normal soil in switch yard as per norms. cable trench should filled by fine sand. 43 hoisting, jumpering, clamping of 33 kv 3x300 sq mm xlpe cable on cable stand / structure with proper jumpering with help of pg clamps ( required pg clamps will be provided by contractor ) . 44 pipe boring type earthing minimum 20 mtr deepfrom ground level or upto water level with b class g.i. pipe 2 dia. connection of equipment with earthing included in the job as per specification / norms for ct / la and other. ( all materials will be provided by contractor ) 45 supply and fixing of cable route marker of 33 kv line 46 safe dragging, loading, carriage and unloading of balanced materials with proper stacking from site to je dump store / lesa store after completion of work....

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

33318522 edck 39 / 2022 23 edck 39 / 2022 23 , supply of material , s.t. pole 13 mtr. sp 55 , s.t. pole 11 mtr. sp 55 , stone pad 300×300×75 mm , 11kv pin insulator with pin & nut , 11 kv disc insulator with fitting ( b&s type 70 kn ) , acsr weasel conductor , x arm m.s. angel 65x65x6 mm v type , al. cable 3x120 sqmm 11 kv xlpe , 11 kv cable jointing kit 3x120 sqmm o / d xlpe , ms angle iron ( 65x65x6mm ) brassing with clamp , acsr dog conductor , stay set complete , earthing rod set complete , barbed wire , 11 kv cable jointing kit 3x120 sqmm i / d xlpe , t channel clamp , number plate with nut bolt , danger board & clamp with nut bolt , red oxide paint , aluminium paint , earth wire clamp with nut & bolt , pg clamp , f bracket with nut bolt , g.i. wire 6 swg ( for support 11 kv cable ) , g.i. wire 6 swg ( straight ) , x arm holding clamp with nut bolt , t channel , m.s. dropper channel , g.i wire 8 swg ( teeli ) , nut bolt off size , top m.s. channel ( 100x50x2240mm ) , g.i. pipe 6 dia , alluminium tape , ms. guarding angel ( 65x65x6x2100mm ) with clamp , irag bolt , xlpe al. cable 11 kv 3x70 sqmm. , id / od cable jointing kit ( 3x70 sqmm ) , clamp with nut bolt , erection of material , erection of single support including complete h.t / l.t fittings s.t. pole 13 mtr. sp 55 including earthing, grouting & muffing of pole. , erection of single support including complete h.t / l.t fittings s.t. pole 11 mtr. sp 55 including earthing, grouting & muffing of pole. , fixing of danger board , guarding of 11 kv line as per respo norms , installation of 11 kv pilfer proof metring cubical ( provided by the department ) , fixing & installation of 11 kv ct / pt metering pole mounted unit ( provided by the department ) , erection of stay set complete including the work of nuzzling etc. , laying sagging stringing, binding and jumpering acsr dog conductor , fixing ofbarbed wire , painting of st pole with red oxide & ailunimum paintas per respo norms , laying sagging stringing, binding and jumpering acsr weasel conductor , laying, sagging of al. cable 3x120 sqmm 11 kv xlpe , laying, sagging of al. cable 3x70 sqmm 11 kv xlpe , fixing & installation of 11 kv cable jointing kit ( id / od ) 3x120 ssqmm & 3x70 sqmm...

Military Engineer Services - Uttar Pradesh

33301934 provision of dental lab at 1 corps dental unit under ge ( east ) mathura as per tender documents 1 surface excavation n exc 30cm deep and averaging 15 cm deep and getting out soft / loose soil complete all as specified and directed. 2 grubbing up tree trunk including cutting of trunk portion protruding over ground, digging out roots, filling holes and leveling off ground, stacking of serviceable material and removing of unserviceable material to a distance n exc. 50 m and clearing site girth of tree exc 100 cm but n exc 150 cm complete all as specified and directed. 3 excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, laying cable etc. and getting out in soft / loose soil complete all as specified and directed. 4 m&l for pcc 1:4:8 type d2 ( using 40 mm graded stone aggregate ) as in foundation filling and mass concrete complete all as specified and directed. 5 returning, filling inincluding spreading, leveling, watering and well ramming in layers not exc 25 cm thick using excavated soil all complete all as directed. 6 removing excavated soil to a distance exc 250 m but n exc 500 m and depositing where directed at a level of n.exc 1.5 m above the starting point all complete all as directed. 7 removal of surplus soil to a distance not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr from starting point complete all as specified and directed. 8 use & waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, plinth beams and similar works for flat rough finished surface complete all as specified and directed. 9 m&l for rccdesign mix m 25 grade, ( using20 mm graded stone aggregate ) as in foundation, footings, plinth beam and similar works complete all as specified and directed. 10 use and waste of formwork to sides of pillars, posts and columns for rough finished surface square / rectangular of concrete complete all as specified and directed. 11 m&l for rccdesign mix m 25 grade, ( using20 mm graded stone aggregate ) as in columns, pillars, piers, posts and struts &similarworks complete all as specified and directed. 12 use and waste of formwork to sides and soffits of floor or roof beams, lintiles cantilever etc for flat rough finished surface complete all as specified directed. 13 m&l for rccdesign mix m 25 grade, ( using20 mm graded stone aggregate ) as in beams, cantilevers, bressummers, lintels& similar works complete all as specified and directed. 14 use & waste of form work to soffits of suspended slabs such as roof slabs floor slab landing and similar work for flat rough finished surface complete all as specified and directed. 15 m&l for rccdesign mix m 25 grade, ( using20 mm graded stone aggregate ) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like& similar rcc works complete all as specified and directed. 16 use & waste of form work to edges of suspended slabs n.exc 20 cm thickness for fair finished surface complete all as specified and directed. 17 demolition of brick work or stone boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed. 18 m&l for brick work with old size fly ash bricks straight or curved on plan exc 6mtr mean radius, built in cm ( 1:6 ) complete all as specified and directed. 19 m&l brick work with old size fly ash bricks straight or curved on plan to any radius in half brick thick walls built in cm ( 1:4 ) complete all as specified and directed. 20 m&l for ms tmt bars 10 mm dia and over cut to length and bent to shape required including cranking bending spirally for hooping for columns hooking end and binding with mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed. 21 m&l for ms tmt bars upto 8 mm dia as in stirrups, cut to length and bent to shape required including cranking bending spirally for hooping for columns hooking end and binding with mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed. 22 m&l for rendering 5 mm thick in cement mortar 1:3 on concrete surface of slab, beam & ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed. 23 m&l for rendering 15 mm thick on other than fair faces of brick wall or concrete surface in cement mortar 1:4 finished even & fair without using extra cementincluding mixing liquid water proofing compound @ 200ml / bag complete all as specified and directed.note: liquid water proofing compound shall be measured and paid separately. 24 supply only liquid water proofing compound complete all as specified and directed. 25 m&l for 15mm thick rendering in cement mortar ( 1:6 ) on fair face of brick wall / concrete surfaces andfinished even and smooth without using extra cement complete all as specified and directed. 26 m&l for preparation of new wall surfacesand applying two coats of exterior emulsion paint ( apex ) over and including a coat of primer complete all as specified and directed. make : asian paint ( apex ultima ) or equivalent item of other specified makes. 27 m&l for preparation of plastered surface of wallsand applying two coats of oil bound distemper of any colour over and including a coat of alkali resistant primer over and including a coat of cement base wall care putty applied as per manufacturers instruction complete all as specified and directed. 28 m&l for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. 29 m&l hardcore of broken stone or boulder gauge n exc 63mm, deposited, spread and levelled in layers n exc 15cm thick watered and rammed to true surface complete all as specified and directed. 30 m&l for 75 mm thick plain cement concrete 1:4:8 type b2, using 40 mm graded stone aggregate, as in sub base to floors and paving etc complete all as specified and directed. 31 s&f light shade coloured vitrified ceramic tiles 10mm thick, ( square / rectangular ) area of each tiles n.exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over and including 15mm thick screed bed in cm ( 1:4 ) complete all as specified and directed. 32 m&l for glazed ceramic tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick plaster incement mortar ( 1:3 ) complete all as specified and directed. 33 m&l for 75 mm thick plain cement concrete 1:3:6, type c1 ( using 20 mm graded stone aggregate ) as in plinth protection surfaces finished even and fair without using extra cement including filling the joints by bitumen and sand mixed in the ratio 1:4 by weight complete all as specified and directed. 34 m&l for 20mm thick black granite stone slab topping table rubbed and polished ( one piece ) in cooking platforms / staps, jambs, pillars, window cill laid over 15mm thick cement screed bed or bedding layer in cm ( 1:4 ) including pointing in white cement ( 1:2 ) using marble dust including rounded / half rounded edge and hole of gas pipe in pre cast slab as well as stone slab in cooking platform complete all as specified and directed. 35 s&f12 mm thick toughened glass shutters ( openable type ) , with clear glass including diamond polishingincluding all hardware fittings detailed as under, fixed in position as per manufacturer instruction complete all as specified and directed.note : ( i ) hardware fitting shall be measured and paid separately as supply only. ( ii ) cat part no of hardware fitting are of make enox. 36 stainless steel top patch ( cat no epf 701 ) 37 stainless steel top pivote ( cat no epf 712 ) 38 stainless steel bottom patch ( cat no epf 702 ) 39 glass to wall stainless steel lock ( cat no epf 799 ) 40 stainless steel floor door spring ( cat no fh eco 842 ) 41 stainless steel handle 300 mm size ( cat no esbh 011 ) 2 nos for each shutter 42 m&l for fixing collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets complete all as specified and directed. 43 m&l for providing and fixing inter locking metal grid ( snap grid for false ceiling ) of size 605 mm x 605 mm in true horizontal level, hot dipped galvanized steel sections ( galvanized @ 120 gram / sqm, both side inclusive ) consisting of main “t” runner with suitably spaced joints to get required length and size 24 mm x 38 mm made from 0.30 mm thick ( minimum ) sheet, spaced at 1200 mm center to center and cross “t” of size 24 mm x 28 mm made of 0.30 mm thick ( minimum ) sheet 1200 mm long spaced between main “t” at 600 mm center to center to from a grid of 1200 mm x 600 mm and secondary cross “t” of length 600 mm and size 24 mm x 28 mm made of 0.30 mm thick ( minimum ) sheet to be interlocked at middle of the 1200 mm x 600 mm panel to form grids of 600 mm x 600 mm and wall angle of size 24 mm x 24 mm x 0.4 mm. main “t” runners to be suspended from ceiling using gi slotted cleats of size 27 mm x 37 mm x 25 mm x 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm gi adjustable rods with galvanized butterfly level clips of size 85 mm x 30 mm x 0.8 mm spaced at 1200 mm center to center along main t, bottom exposed width of 24 mm of all t sections shall be pre painted with polyester paint, all complete for all heights as per specifications and directed. 44 s&f powder coated aluminium frame ( minimum thikness of powder coating 50 micron of approved tint / colour ) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. 45 supply and fixing factory made upvc white colour sliding window three track made of extruded profiles with wall thickness of 2.3mm ( 0.2 mm ) .windoow profile with hollow section with multi chamber.frame ( 88 mm x 52 mm ) , sliding sash ( 42 mm x 67 mm ) .sliding mesh sash ( 42 mm x 57 mm ) slide interlock ( one vertical length in each shutters ) ( 45.5 mmx 28 mm ) , glazing bead ( 24.5 mm x 16 mm ) will be mitered cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water etc. making arrangement for fising of hardware.epdm gasket1.2+ 0.2mm mm thick galvanized steel frame ( 30mmx18 mm ) 2 nos , sliding sash ( 30 mm x 18 mm ) , sliding mesh sash ( 26 mmx 10 mm ) profile to be inserted in required profile , frame will be fixed to wall with 8 mmx100 mm long fasteners. hardware touch lock of zinc alloyed ( white powder coated ) , steel roller system, stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and required accessories. ( note : the unit rate quoted by contractor excludes cost of glass and stainless steel wire cloth but includes all other connected accessories.net opening will be measured for payment purpose. ) area n exc 1.00 sqm each all as specified in td no cejz / td / 2021 / s 01 sheet. 1 / 1 dt 28 jan 2020 complete all as specified and directed. 46 s&f powder coated aluminium ( powder coating shall not be less than 50 microns of approved tint / colour ) door shutters, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and directed. 47 m&l double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty and fixed complete all as specified and directed. 48 supply only 5 mm sheet glass, ordinary quality and area n exc 0.5 sq. m in each pane complete all as specified and directed. 49 supply only 5.5 mm sheet glass, ordinary quality and area exc 0.5 sq. m in each pane complete all as specified and directed. 50 supply and fix stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 51 m&l for framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con forming to fe.290.gde e 165 complete all as specified and directed. 52 m&l for preparation of new steel surface of any description not otherwise described exc 10cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed. 53 m&l app based polymeric membrane not less than 3mm thick weighing not less then 3.5 kg / sqm, reinforced with polyster non woven fabric ( weighing ) not less than 150 gm / sqm ) and upper side of membrane thermally insulated with white mineral gravel finish, uniformly embedded during manufacturing process, shall be used it shall be laid by torch application. side overlaps shall be 75 mm and the ends shall be 100 mm and all overlaps and joint shall also be sealed by torch application. for parapets, membrane shall be taken to a height of minimum 60 cm and then inserted inside the parapet in a grooves. the same shall be finished by a membrane flashing over a coat of cold applied bituminous primer confirming to is : 3384 @ 0.40kg per sqm complete all as specified and directed 54 blank 55 s&f 15 mm bore gi tubing medium grade including all fittings & fixture fixed to walls and ceilings or laid in floors complete all as specified and directed.note : cutting chases for consealed tubing will be measured and paid separately in respective item of this schedule. 56 cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth of brick walls complete all as specified and directed. 57 s&f 20 mm bore gi tubing medium grade including all fittings & fixture fixed to walls and ceilings or laid in floors complete all as specified and directed. 58 s&f for stainless steel sink 1 mm thick for kitchen or laboratory with plug waste pipe, washers including cantilever cast iron brackets connecting union etc over all size 495 x 420 mm with bowl size 410 mm x 330 mm x 160 mm. complete all as specified and directed. 59 s&f15mm dia bore stop valves / angle cock chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. 60 s&f 15mm bore long body chromium plated cast copper alloy bib taps with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed.make : jaquar cat part no fus chr 29037 or equivalent item of other specified makes. 61 s&f towel rail 600 mm long complete all as specified and directed.make:jaquar cat no.acn 1111nm or equivalent item of other specified makes as given in appendix b to particular specification. 62 s&f 32 mm dia waste pipe of min 750 mm long fixed to waste coupling and to grating complete all as specified and directed. 63 s&f 75 mm dia of outlet pvc ( swr ) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. 64 s&f 75 mm pvc ( swr ) pipes type a single socketed, inanylength with rubber ring joints, laid in trenches or in floors complete all as specified and directed. 65 s&f 110 mm pvc ( swr ) pipes type a single socketed, inanylength with rubber ring joints, laid in trenches or in floors complete all as specified and directed. 66 supply and fix 1000 litre capacity white colour triple layer rotational moulded polyethylene water storage tank ( cylindrical vertical with closed top ) hoisted and fixed in position including making inlet / oulet connection and fitting tank connection complete all as specified and directed. 67 supply and fix 20 mm bore dia ball valves high pressure of ptmt with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete all as specified and directed. 68 s&f 20 mm gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixedcomplete all as specified and directed. 69 s&f welded steel wire fabric supplied and fixed to angle frame or steel members complete all as specified weight per square metre n exc 4 kg complete all as specified and directed. 70 s&f butt hinges 100mm medium weight cold rolled mild steel including necessary welding if required complete all as specified and directed. 71 s&f 100 mm hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed. 72 s&f factory made 18mm ± 0.7 mm thick rajshri brand celuka pvc ply one side prelam and one side plain sheet kitchen cabinet shutter of density 600 kg / cum bent at 90 degree and finish all edges at level for making edge lipping / bending or 0.5mm thick pvc sheet lipping at all four edges using bonding tape etc complete all as specified and directed. 73 s&ffactory made pvc board 12 mm thick pvc celuka ply fixed with each other using solvent cement adhesive and fixed with screw etc. complete as per manufacturer specifications including dismantling of old cabinet complete all as specified and directed. 74 ms&f 18mm ± 0.7 factory made pvc shelf / partition of required size consisting of panel of celuka pvc ply and for supporting the hold of shelf / partition and shall provided 3 edges in size 18mm x 18mm as per required lengh the front size of the edge visible in the front of the shelf / partition the edge lipped by 18mm width x 1mm thick pvc sheetof density 600 kg / cum complete all as specified and directed. 75 s&f 25 mm size magnetic catches for cupboards including fixing to frame and connected plate to shutter complete all as specified and directed. 76 s&f 100mm size brass handles, cast type, polished bright complete all as specified and directed. 77 s&f continous piano hinges mild steel bright finish or electro galvanised of 40mm width of flaps ( when open ) complete all as specified and directed. 78 m&l for 100 mm thick cement concrete 1:4:8 type d2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed. 79 m&l for machine pressed precast conctete coloured interlocking paver block any shape and size confirming to is 15658 2006 of 80 mm thickness m 40 grade made with grey cement and pigmentwith and including laid over 25mm thick sand chshioning and joint of pavor block to be filled with same sand complete all as specified and directed. 80 s&f coloured non skid endura ceramic tiles 10mm thick, ( square / rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cm ( 1:4 ) complete all as specified and directed. 81 m&l steel work in tubular trusses including special shaped washer etc complete using erw or including butt welded tubes conforming to is 1161 1979 grade st 240 complete all as specified and directed. 82 m&l for providing acrylic sheet 2 mm thick of any colour as directed fixed to steel frame work complete all as specified and directed. 83 cutting existing steel tubing of size 25 / 32mm bore for alterations or additions ( each cut measured ) done in position without taking down complete all as specified and directed. 84 screwing existing steel tubing 25mm bore for alterations or additions ( or lenghtening screw on pipe to form connector ) done in position without taking down complete all as specified and directed. 85 m&l for steel water tubes, medium grade, galvanised, with all fittings , laid in trenches fixed to wall of size 25mm dia and connecting with existing lines with suitable gi tee including testing complete all as specified and directed. 86 m&l for gun metal gate valve with iron wheel head, screwed both ends for iron pipe of size 25mm dia complete all as specified and directed. 87 m&l for 4mm thick non asbestos fiber cement building boards fixed or laid / inserted on frame work fixed in ceiling complete all as specified and directed. 88 m&l for antitermite treatment by treating the bottom and sides of excavation at the rate of 5 liters of emulsion per sqm of surface area complete all as specified and directed. 89 m&l for antitermite treatment by treating the top surface of filled earth at the rate of 5 liters of emulsion per sqm of surface area complete all as specified and directed. 90 m&l for antitermite treatment by treating the soil under plinth protection at the rate of 5 liters of emulsion per sqm of surface area complete all as specified and directed. 91 m & l for point wiring with 1.5 sqmm ( nominal area ) single core pvc insulated unsheathed ( frls ) cable, multi stranded, copper conductor, inuniversal colour code with & including suitable size of rigid non metallic pvc conduit ( not less then 20mm dia med gd ) and its all accessories complete concealed in wall / roofincl cutting & chases ( making good all to the disturbed surfaces as per existing ) and modular flush metal boxessuitable for modular fittings including modular cover plate with framefor mounting modular switches, sockets, etcincluding earth wire ofpvc insulated ( frls ) copper conductor multistrandedof 1.5sqmmsize in green colour complete all asspecified in current ssr part i & ii & directed by the engineer in charge , as described below: 92 one light point controlled by one way switch 6 amp complete. 93 oneceiling fan / exhaust fanpoint controlled by one way switch 6 amp complete. 94 one 3 pin 5 amps socket point controlled by one switch on independent board. 95 one 3 pin 5 amps socket point controlled by one switch on same board. 96 all as per item no. 85.00 butfor 3 pin / 5 pin 16 amps sockets outlet with 4 sqmm pvc insulated & unsheathed ( frls ) copper conductor cable independent complete all as specified and as directed . 97 supply and fixing ceiling rose surface bakelite 65mm x 50mm three terminals complete all as specified and directed. 98 supply and fixingmodular switch 6 amps single pole one way, 1 module complete all as specified and directed. 99 supply and fixingmodular switch16 amp single pole one way, 2 module with indicator complete all as specified and directed. 100 supply and fixing modularsocket2 in 1, 5 pins 6 amps , combined 2 modulecomplete all as specified and directed. 101 supply and fixingmodular socket 2 in 1, 3 and5 pins 6 / 16 amps, combined 2 module complete all as specified and directed. 102 supply & fixing modular fan regulator electronic step type 120watt, 2 module complete all as specified and directed. 103 supply & fixing indoor decorative ultra slim surface / wall mounted t5 ledbatten tube light complete fitting 1x 20 watt led tube fittingwith polycarbonate channel housing & integrated electronic driver, energy efficient, 140v 270 volts, complete all as specified and directed by enginee in charge.make:havells ( as per cat part no: lumilinebs20wled 865 spc wh ) or equivalent item of other specified makes as given in appendix b to particular specification. 104 s&f mcb distribution board, spn 8 way, double door, sheet steel, phosphatised, powder painted with copper bus bar 200amp, neutral link, earth bar and din rail , cable ties for cable management, 240 v, complete all as specified and directed. 105 supply & fixing mcb sp 6 32 amps, b series , bracking cap10ka complete all as specified and directed. make : havells or equivalent item of other specified makes as given in appendix b to particular specification. 106 supply & fix mcb dp 63 amps, c series , bracking cap10ka, 240v complete all as specified and directed.make : havells or equivalent item of other specified makes as given in appendix b to particular specification. 107 supply and install of 30w led building security light fitting with lens & driver, powder coated pressure die cast aluminium, top opening and maintainablewith heat resistance toughened glass, built in short circuit protection, over voltage protection and surge protection, ip 65 protection with luminaire efficiecy of greater than 80lumen / watt, colour rendering ( cri ) of = 70 and co relatedcolour temperature ( cct ) of 5700k ( ±500k ) . the luminaire should have 10 kv surg protection, pf= 0.9 and total harmonic distortion of thd = 10%, voltage range of 140 280vincluding all connections complete all as specified. make of fitting : havells cat part no : enduracityliteplat plussl30wled757sasybopc or equivalent item of other specified makes as given in appendix b to particular specification. 108 m&l for building securitylight bracket made out of 40mm dia light grade gi pipe of 1.2 m length bent to required shape suitable for fixing street light fitting on steel tubularpole including two nos clamps made out 40mm x 6mm flat with suitable nuts and bolts including two coats of aluminium paint over a coating of red oxide primer complete all as specified and directed . 109 m&l for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground not less than 2.25 mtrs deep below normal ground level with top edge of the plate not less than 1.5 mtrs below normal ground level, surrounded from all sides with mixture of charcoal and common salt, connected to galvanized earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel protected by galvanised iron light grade 15 mm dia pipe and20mm light grade for water filling including 15x20mm reducer socket funnel wire mesh, rcc cover with concrete 1:2:4 using 8 mm dia bar@100 mm c / c both ways, ms handle 12mm dia for pcc chamber pit with pcc ( 1:3:6 ) type c 2 and excavation and earth work in hard / disintegrated rock all as specified and shown on electrical plate no. 3 of 2009 ( part i ) and connected to earth test point including testing complete all as specified and directed.note : the unit rate includes for protection pipe and gi wire 4mm dia from top of earth plate up to 7.5 meter above ground level. 110 m&l for galvanized iron tubes 15mm bore light grade confiming to is 1239, laid in trenches or alongwall for protection earthing lead from mechanical injury or tapmpering complete all as spcified and directed. 111 m&l for gi earth lead 4mm burried in ground / fixed on walls complete with fixing screws, nut, bolts etc complete all as specified & directed. 112 s&f tp&n vertical loadline distribution board, 4 way, double door, sheet steel, phosphatised, powder painted with copper bus bar 200 amp, neutral link, earth bar and din rail, blanking plates, cable ties for cable management, 440 v, 4 way complete all as specified and directed including fitting with following mccb & mcbs with connections : ( i ) mccb 100 amps, 4 pole, 16ka 01 nos ( ii ) mcb sp 63 amps 04 nosnote : mccb, mcbs & mcb db shall be of the same make. mcb dbs shall be fixed on wall in flush pattern by cutting the wall and making good disturbed surfaces. 113 supply and fix ceiling fan 1200 mm sweep, energy saving models, pearl white / white in colour 350 rpm, 220 volt 50 hz complete with canopy, down rod. fan blade, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed by enginee in charge. make : havells ( model no es 40 ) or equivalent item of other specified makes as given in appendix b to particular specification. 114 supply and fix modular power socket 16 amp unit protected with 16 amp sp mcbincluding with sheet enclosuer complete all connection complete all as specified and directed. make : havellsas per cat part no dhdmcsn0251016or equivalent item of other specified makes as given in appendix b to particular specification. 115 m&l for submain wiring with 2 runs of single core 4 sqmm pvc insulated unsheathed multistranded 1100 volts grade with frls copper conductor drawn through and including isi marks pvc conduit concealed and conduit accessories of medium grade not less than 20mm dia including one run of single core 4 sqmm frls pvc insulated unsheathed multistranded 1100 volts grade with copper conductor cable as earth conductor along with wiring and connected from db to db / main board complete all as specified and directed.note : two run of 4 sqmm cable and one run of 4 sqmm earth cable and one run of 20mm pvc conduit shall be considered as a unit for measurements purpose. 116 m&l submain wiring with 2 runs of single core 6 sqmm pvc insulated unsheathed multistranded 1100 volts grade with frls copper conductor drawn through and including isi marks pvc conduit concealed and conduit accessories of medium grade not less than 20mm dia including one run of single core 6 sqmm frls pvc insulated unsheathed multistranded 1100 volts grade with copper conductor cable as earth conductor along with wiring and connected from db to db / main board including taking down old unserviceable submain wiring complete all as specified and directed.note : two run of 6 sqmm cable and one run of 6 sqmm earth cable and one run of 20mm pvc conduit shall be considered as a unit for measurements purpose. 117 supply and fix storage type water heater ( geyser ) of 15 litres capacity, 5 star rating, 2kw rated power, incoloy glass coated heating element, thermostat cutout temperature ( ºc ) , adjustable knob for temp setting , vertical type , to operate on single phase, 230 volts, 50 hz ac supply & complete with all safety controls including provision of suitable bolts, nuts, washers and grouting on walls and making good the disturbed surfaces to match with the existing sufaces and provision of suitable pvc flexible pipe for hot & cold connection, chromium plated brass check nuts for cold & hot water lines and one no. non return valve of suitable sizecomplete installation with testingall as specified and directed 118 supply, laying and testing cable xlpe insulated , screened, pvc bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty ) 1100 volts grade with stranded aluminium conductor of size 25 sq mm 4 core, laid in trenches / duct / fixing on walls / poles or passing through pipe including connecting with suitable lugs, glands, nuts and bolts and testingincluding connecting with suitable lugs, glands, nuts and bolts in existing panelfrom pole / main panel box and testing complete all as specified and directed. 119 m&l for hdpe double wall corrugated pipe of size 40mm outer dia and 32mm inner dia confirming to is:14930 part iiincluding necessary pipe fittings such as couplers, end caps, bend etc. laid in trenches / fixed to wall with suitable clamps for cable protection complete all as specified and directed. 120 supply, install & testing hi wall split air conditioning units of capacity 1.5 tr complete with indoor & outdoor unit with cordless remote control unit and with in built air ioniser and plasma filter for better indoor air quality with minimum bee 4 star rating and eer 3.2including outdoor mounting stand complete all as specified and directed. make daikin or equivalent item of other specified makes. 121 s&f wall mouunted indoor voltage stabilizer automatic operation single phase , naturally air cooledand disigned for input variation between 130 v to 300 volt with output voltage stabilized at 230 v with accuracy of + 2.5% and of capacity 3800va. make v guard as per model vgb 500 or equivalent item of other specified makes. 122 supply and fix dp enclosure with a two pin and earth plug and socket complete with dp mcb of rating 20 amps, 240 volts complete with all conction as directed....

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

33258083 06 no. work under edd jhansi and mauranipur under deposit scheme namami gange 1 supply and commissioning ofthe whole following work including carriage, commissioning with all required material. note: all required material to be supplied as per gtp approved by se mm dvvnl agra.do not quote supply item rates in errection column and errection part rate in suppy item column please read the boq carefully then quote the rates. 2 8.5 mtr long pcc pole 3 11 meter long stp ( sp 55 ) 4 13 meter long stp ( sp 72 ) 5 stone pad 300x300x75mm 6 v type cross arm for 11kv 7 x arm holding clamp with nut & bolt 8 f bracket for top insulator with nut & bolt 9 ms t off channel 10 ms angle t / fbase 75*75*2028mm 11 11 kv disc insulator ( b&s ) type 12 disc fittingfor weasel / rebbit ( b&s ) type 45 kn 13 11 kv pin insulator with pin 14 stay set complete for 11 kv 15 earthing complete ( ms earthing rod ) 16 acsr dog conductor 17 acsr weasel conductor 18 aluminium binding wire 19 ms angle guardingx arm 20 gi wire 6 swg for guarding 21 eye bolts for guard wire with nut 22 ms top channel 125x65 2240 mm 23 dropper channel 100x50x2028mm 24 ms bracing angle long 25 clamp with nut bolt top channel 26 dp clamp 27 pg clamp 28 clamp with nut bolt 29 alluminium paint 30 red oxide 31 11 kv 3x70sqmm jointing kiti / d and o / d 32 11 kv 3x120sqmm jointing kiti / d and o / d 33 11 kv 3x185sqmm jointing kiti / d and o / d 34 11 kv 3x300 sqmm jointing kiti / d and o / d 35 making of 11 kv cable boxmounted with switchgears and transformers 36 fixing of barbed wire 37 fixing of number plate 38 fixing of denger board 39 11 kv xlpe 3x70cable as per respo maual and including costof labour. 40 11 kv xlpe3x120 cable as per respo maual and including costof labour. 41 11 kv xlpe3x185 cable as per respo maual and including costof labour. 42 11 kv xlpe3x300 cable as per respo maual and including costof labour. 43 gi pipe 150mm ( 6 ) thickness 4.80mm as per gtp approved by se mm dvvnl agra. 44 errection and commissioning ofall required material forinstalation of meteringsystem on pcc pole / meter including the work requiredfor energising the line including carriage of material from store centre hansari to work site.11 kv pilfer metering cubical meter, 11 kv ct / pt, meter cubical andtvmprovided by the department. 45 fixing & installation, errection and commissioning ofthe following 11 / 0.4 kv s / s with material including the work requiredfor energising the line and work includes carriage to work site with earthing, grouting, laying, sagging, strenthing, binding of conductor.11kv vcb incoming & outgoing ctr provided by the department. 46 11kv vcb incomingctr 400 / 200 / 5a350mva ( material will be provided by department ) 47 11kv vcb outgoing ctr 200 / 100 / 5a 350mva ( material will be provided by department ) 48 33 kv vcb control panel for single t / f & 33kv vcb with ctr 200 / 100 / 1a alongwith structure without differential relay 49 33 kv bus isolator 50 33 kv post insulator 51 33 kv lightening arrester 52 bus coupler 350 mva 53 10 mva 33 / 11 kvpower t / fwith accessories including oltc ( material will be provided by department ) 54 strengthning of power t / f plinth 55 dismantling of 5mva t / f & cartage it to nearest store 56 11 kv tpmo 57 11 kv fuse set 58 alluminium lugs 59 copper l piece 50*225*10mm 60 4 core lt mcb box 61 control cable 4*2.5 sqmm 62 l.t. pvc cable 3.5*400sqmm 63 painting of indoor equipments 64 earthing of indoor equipments 65 chemical pipe earthing as additional earthing ( for t / f, la, ct & pt ) 66 lt incoming panel with metering equipments & fixing arrangement 67 base angle for ct / pt 68 11 kv ct pt unit ( material will be provided by department ) 69 stay insulator 70 laying 11 kv xlpe 3*70 cable 71 laying 11 kv xlpe 3*120 cable 72 laying 11 kv xlpe 3*185cable 73 laying 11 kv xlpe 3*300cable 74 11 kv pilfer proof metering cubical ( ( material will be provided by department ) ) 75 laying and fixing of gi pipe 150mm ( 6 ) thickness 4.80mm as per gtp approved by se mm dvvnl agra. 76 nut bolt with washer all size 77 concreating of support 78 concreating of stay...

Lucknow Development Authority - Uttar Pradesh

33234437 in gomti nagar extension scheme sector 5, the work of providing electricity supply for newly created land number 444 to 456 and plot number 5 / 366 1 supply & fixing steel tubular pole 9.50 metre long designated 410 sp 36 in 1:3:6 cement concrete foundation including excavation back filling etc. complete in all respect. as e / i si no 616 / 2018 2 s / e of over head with areal bunch conductor lt xlpe cable ( abc ) of size 3x95+1x70+1x16 approved quality ( pci approves ) on poles / service bracket including dinding etc all complete with labour t&p cost of material all as per direction of e / ic. 3 supply of dead end clamp complete in all respect. as per uppcl specification. 4 s / f of suspension clamp complete in all respect. as per uppcl specification. 5 s / f of eye hook for dead end clamp complete in all respect. as per uppcl specification. 6 s / f of 40 mm dia 1.5 mt long gi pipe street light bracket complete with 2 nos ms d clamp with required nut bolt as per direction of e / ic 7 supply and fixing ofled street light fittinghaving die cast aluminium body and diffuser with driver set suitable for 75 to 90 watt. confirming to ip 66 and aboveprotection complete in all respect. pwd 2018 / 1423 cat aaa 8 supply & erection of d clamps of 50 mm x 6mm flat iron on steel tubular poles / steel rail poles with bolts, nuts etc. complete in all respects including painting with aluminium paint . pwd 2018 / 623 9 supply & erection of stay set at least 3.5 metres away from the pole complete with galvanised 19 mm dia x1.80 metre long stay rod, 30 cm x 30 cm x 6.3 mm anchor plate, thimble stay clamps, stay insulator, 19 mm x 600 double screw tightener, 7 / 4.00 mm g.i stay wire etc. in 1:3:6 cement concrete complete in all respect.pwd 2018 / 630 10 painting of the electric pole with 2 coats of aluminium paint over red oxide primer complete in all respect.pwd 2018 / 634 11 s / b of earth rod20 mm dia 2.5 mt long including gi wire 7 / 16 sqg to connected earth rod and earth clamp on pole 3 mt long steel conduit to carry earth wire along the pole complete as per approved of e / ic 12 s / f of 3 phase 10 ways distribution consumer board for arial bnch conductor complete with fixed on pole all complete as per uppcl specification or as per direction of e / ic ( approved rate ) ...

Kisan Sahkari Chini Mills Limited - Uttar Pradesh

33182850 supply of paint and varnish items for season 2022 23 supply of paint and varnish items for season 2022 23 , supply of paint and varnishitems , zink chromate red oxide metal primer (heat alkali and temp. resistant.) , heat resistant anti sulphuric off white paint , g.p. aluminum paint (thiner +paste) , black bituminous heat resistant paint , g.p. bus green enamel paint , g.p. p.o red enamel paint , g.p. golden yellow enamel paint , g.p. sky blue enamel paint , g.p. smoke grey enamel paint , g.p. white enamel paint , g.p. black enamel paint , g.p. thiner , heat resistant black paint ferrotol no. 1 forinternal use suitable for 300c. , heat resistant black paint appoxior no.3 forexternal use suitable for 300c. , heat resistant aluminium paint for chimneyfor external use suitable for 200c. , painting brush size 1 , do 2 , do 3 , do 4...

Northern Railway - Uttar Pradesh

33125712 supply of aluminium paint for generalaluminium paint for general,aluminium paint for general purpose in dual container for coaching stock. spec. : is 2339/1963 rev.4...

Reserve Bank Of India - Uttar Pradesh

33088968 1 providing and applying a coat of approved quality water based exterior alkali & fungal resistance primer ( 1.1 of nit ) 10 ( ten ) building blocks of class iii indicative quantity / area of each building / block = 1674.00 sqm. ( each block has 16nos. class iii flats ) . please refer to price bid document and nit for details. 2 2 providing and applying a coat of approved quality ( 1.2 of nit ) 4 ( four ) building blocks of class iv, indicative quantity / area of each building / block = 1281.00 sqm. ( each block has 16 nos. class iv flats ) . please refer to price bid document and nit for details. 3 3 providing and applying a coat of approved quality ( 1.3 of nit ) community hall block which include hall, adjoining utility building, toilet wall etc. indicative quantity / area = 1388.00 sqm. please refer to price bid document and nit for details. 4 4 providing and applying a coat of approved quality ( 1.4 of nit ) compound wall which include three side of compound wall both side and adjoin wall with other colony wall single side. indicative quantity / area = 1733.00 sqm. please refer to price bid document and nit for details. 5 5 providing and applying a coat of approved quality ( 2.1 of nit ) 10 ( fourteen ) class iii block?s staircase upto mumty, indicative quantity / area of each staircase = 463.00 sqm. please refer to price bid document and nit for details. 6 6 providing and applying a coat of approved quality ( 2.2 of nit ) 4 ( fourteen ) class iv block?s staircase upto mumty, indicative quantity / area of each staircase = 393.00 sqm. please refer to price bid document and nit for details. 7 7 providing and applying two or more coats of approved 1st quality synthetic enamel paint ( 3 of nit ) indicative approximate quantity / area ( inclusive of all the co efficient ) for all type of buildings = 4861.00 sqm. please refer to price bid document and nit for details. 8 8 providing & applying two or more coats of approved quality ( 4 of nit ) providing & applying two or more coats of approved quality synthetic enamel paint / premium acrylic smooth exterior paint with silicone additive, high sheen / varnishing / polish / synthetic enamel paint / aluminum paint etc. of approved make & shade as per specifications with smooth finishes please refer to price bid document and nit for details....

Kisan Sahkari Chini Mills Limited - Uttar Pradesh

33075856 supply of paint and varnish items for season 2022 23 supply of paint and varnish items for season 2022 23 , supply of paint and varnishitems , zink chromate red oxide metal primer (heat alkali and temp. resistant.) , heat resistant anti sulphuric off white paint , g.p. aluminum paint (thiner +paste) , black bituminous heat resistant paint , g.p. bus green enamel paint , g.p. p.o red enamel paint , g.p. golden yellow enamel paint , g.p. sky blue enamel paint , g.p. smoke grey enamel paint , g.p. white enamel paint , g.p. black enamel paint , g.p. thiner , heat resistant black paint ferrotol no. 1 forinternal use suitable for 300c. , heat resistant black paint appoxior no.3 forexternal use suitable for 300c. , heat resistant aluminium paint for chimneyfor external use suitable for 200c. , painting brush size 1 , do 2 , do 3 , do 4...

Department Of Heavy Industry - Uttar Pradesh

33075024 bids are invited for chemical resistant epoxide red oxide zinc phosphate priming paint (spec: aa56105) (q3) , red oxide zinc phosphate (alkyd base) to is 12744 spec: aa56101 (q3) , thinner for alkyl based paint spec: aa56701 (q3) , heat resistant aluminium paint, as peris 13183 gr i, as per specs aa56149 (q3) , thinner forheat resistant aluminium paint gr i as per is 13183(q3) total quantity : 16700...

Kisan Sahkari Chini Mills Limited - Uttar Pradesh

33056250 supply of new i.d. fan for 20 tph boiler new i.d. fan for 20 tph boiler , new i.d. fanfor 20 tph boiler , fabrication & supply of new i.d. fan impeller with hub & shaft identical in all respect to our existing fan for m / si.j.t. make 20 tph capacity bagasse fired boiler having ventury type wet scrubber after i.d. fan, having following specification: fan rpm 900, no of blades 09 nos, blade length 730mm, blades must have hard faced wear pad. shaft moc en 08 for ged , shaft must be ultrasonically tested with test report impeller od 1875mm, impeller width at top 200mm, back plate 12mm thick with 10mm thick wear plate, shaft length 1550mm, keyway 90mm long x 25mm width x 06mm depth, fitted bearing 22222k, shaft od 100mm, pulley size 90mm, suction id 800mm, shroud 6mm, finishing heat resistance aluminium paint fan must be dynami cally balanced with report....

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

33052611 tender for semi turnkey work jal jeevan mishan 2 carriage offollowing line materials for 11 kv line from center store to thesite of work including measuring weiging loading unloading at both ends and proper stacking at safe site. 3 st pole 11 mtr long 4 pcc pole 8.5 mtr long 5 dog conductor 6 3x70 sqmm 11kv xlpe cable ( in mtr ) 7 wesel conductor 8 t / f 400 kva new 9 t / f 250kva new 10 11 kv t.p.m.o 11 11 kv fuse set 12 3x120 sqmm 11kv xlpe cable ( in mtr ) 13 11 kv metring pilfer of ctr 10 / 5 amp 14 11 kv double merting ct / pt unit of 10 / 5 amp. 15 11 kv vcb in coming ( 600 / 300 / 5a ) 16 11 kv vcb out going ( 200 / 100 / 5a ) 17 part b 18 supply of the following line item as per resspo drawing & dimension: 19 stone pad ( 300x300x75mm ) 20 11 kv v type cross arm with holding clamp and nut and bolts 21 stay set complete with stay clamp and nut bolts 22 11kv pin insulator with g i pin 23 11kv disc insulator 45 kn 24 11kv disc fitting for rabbit conductor 25 m.s. earthing complete ( 16mm dia, 3mtr long ) 26 f bracket for 11kv line with nut & bolts 27 gi pipe c class of 6 dia 28 i / d & o / d cable jointing kit make rychen / denson 29 barbed wire ( no of pole x1.5kg ) 30 danger board with clamp of size ( 250x200x2mm thick ) 31 number plate ( 250x200x2mm thick ) 32 t off channel of size ( 125x65x1300mm ) with clamp 33 m.s. dropper channel ( 100x50x2028mm ) with clamp 34 m.s. top channel ( 125x65x2240mm ) with clamp 35 m.s. top channel ( 125x65x3200mm ) for four pole with clamp 36 transformer base angle ( 75x75x6x2028 mm ) 37 m / s angle cross bracing of size ( 65x65x6x2700 mm long ) 38 red oxid paint 39 aluminium paint 40 aluminium binding wire 41 off size bolt nut & washer 42 gaurding angle 65x65x6 ( 1600mm long ) 43 g.i wire 7 swg 44 eye bolt 45 part c 46 erection of the following supports after making of pits as per resspo norms & filling of pits by concrete of ratio 1:4:8 ( cement brick balast & sand ) . fitting of all accessories as cross arm, top channel, bracing angle, pin insulator, disc insulator, danger board, number plate, barbed wire & clamps etc. plinthing of support above 300mm ground level by concrete of ratio 1:4:8 ( cement brick balast & sand ) will be done at the time of erection of pole. painting of st pole structure as per resspo norms also ( all type of paints, red oxide primer, nut, bolts & grouting material etc. will be provided by contractor ) . 47 single support of s.t pole 11 mtr long. 48 double pole structure on s.t. pole 11mtr long complete with bracing. 49 double pole structure on st pole 11 mtr long for sub station 50 four pole structure on st pole 11 mtr long complete with bracing. 51 single support of pcc pole 8.5 mtr long. 52 erection of stay set with stay wire, stay clamp & stay insulator including with grouting of stay set by concrete of ratio 1:4:8 as per resspo norms before back filling of the pits including binding, climbing, clamping, tightening and nozzeling of stay wire in all respect as per resspo norms. all clamps, nuts, bolts, stay insulator, cement. brick, ballast, sand etc would be provided by the contractor. 53 laying and sagging of 3 phase acsr rabbit / weasel conductor from double pole at 33 / 11 kv substation to double pole at tapping point of 11 kv feeder line including jumpering, hoisting fixing all type of insulators, binding jointing and its clamping etcin all respect. as per respo norms. 54 earthing of each st & pcc poles of the line is to be done by inserting the ms earth rod ( 1800x16mm ) into soil by hammering and properly fastning with gi wire to each support & its accessories by nut & bolt. earthing rod must be 0.15mtr.above from the plinth of the support. all type nut & bolt, earthing and gi wire will be suppliedby the contractor. 55 guarding of ht / lt line / road / river crossing etc. by providing g.i earth wire 7swg and making net with difference of 1.00 mtr. completely including fixing of channel / angle etc. with proper locking at each support as per resspo norms. all type nut &bolts, would be provided by the contractor. 56 laying ofdouble circuit 11 kv 3x120 / 3x70 sq. mm xlpecable in normal soil in g.i. pipe by digging of trench 1050 mm deep, 750 mm wide including supply of required material as hdpe pipe, fine sand, 1st class bricks, stone slab. interaxial spacing between the two cable should be in between 0.25 m to 0.40m. 57 laying ofsingle circuit 11 kv 3x120 / 3x70sq. mm xlpecable in normal soil in by digging of trench 1050 mm deep, 750 mm wide including supply of required material as , fine sand, 1st class bricks, stone slab. will be supplied by contractor. 58 fixing of 11 kv 3x120 / 3x70sqmm o / d and i / d sizes, makeraychem / denson. ( cable box will be supplied by the contractor ) . 59 termination of 11 kv 3x120 / 70 sq mm size xlpe cable by filling 11 kv heat shrinkable type cable boxes including proper connection with 11 kv line, double metring ct / pt unit, 11 kv metring pilfer and 11 kv switch gears and double poles by providing suitable connectors.all the 11 kv cable boxes of different sizes makeraychem / denson. ( cable box will be supplied by the contractor ) . 60 painting of following support of existing 11 kv line with one coat of red oxide primer and two of alluminium white paint of isi mark and top danger portion of each support must be painted by providing two coat of red paint. 61 hoisting of 11 kv 3x120 sq. mm. xlpe cable on double pole with c class gi pipe of size 6 dia 3 m longincluding its jumpering complete with clamps, nuts and bolts. 62 construction of t / f plinght and fencing for 250 / 400 kva t / f of size 2x2x1.5 mtr. 63 installation of 11 kv metring pilfer in meter room and making h.t connections. 64 installation of double metring ct / pt unit. 65 clearing of the line route by cutting of tree branches during erection of line and also upto the time of energisation completely as per direction of site incharge....

Ganga Kisan Sahakari Sugar Mills Limited - Uttar Pradesh

33025235 supply of industrial paint industrial paint , berger / asian paint , hr aluminium / paste paint for boiler 250c , post office red paint , bus green paint , golden yellow paint , azure blue paint , smoke gray paint , red oxide metal primer , heat resistance zink chromate red oxide paint , off white paint , white paint , aluminium paint , heat resistance hr black paint , thiner...

Purvanchal Vidyut Vitaran Nigam Limited - Uttar Pradesh

33016045 1 supply of materials 2 stp 11mtr long 3 pcc pole 8.5 mtr long 4 acsr dog conductor 5 acsr weasel conductor ( 930x3+3% ) 6 11kv pin insulator 7 11kv pin with nut 8 11kv disc insulator t&c type 45kn 9 11 kv disc fitting t&c type 45kn 10 11 kv v type cross arm ( angle 65x65x6 ) 11 stay complete 1650x15mm 12 earthing complete 13 ms channel 125x65x1300 ( tee off ) 14 ms channel 125x65x2240 ( top ) 15 ms angle 75x75x6x2028 mm with clamp & bolt & nut ( t / f base ) 16 ms channel ( dropper ) 100x50x2028 mm for fuse set 17 guarding cross arm ( ms angle 65x65x6mm ) 18 gi wire 5mm 19 100kva t / f 20 3x120 sq.mm 11kv xlpe cable ( 90x2+20 ) 21 11kv xlpe c / j kit 3x120sq.mm outdoor 22 11kv xlpe c / j kit 3x120sq.mm indoor 23 stone pad 24 holding clamp for top channel 25 x arm holding clamp 26 f bracket 27 clamp for tee off with nut & bolt 28 danger plate with clamp 29 barbed wire 30 guarding clamp for guarding cross arm 31 alluminium paint 32 red oxide paint 33 eye bolt for guard wire 34 nut bolt of various size 35 gi pipe 6 dia 36 hdpe pipe 100mm 37 pipe holding clamp 38 cable holding clamp 39 alumium binding wire 40 erection of work 41 errection and complete fitting of st pole 11mtr long 42 errection and complete fitting of pcc pole 8.5mtr long 43 errection and complete fitting of double pcc8.5 mtr pole 11mtr long 44 sagging of 11 kv line ( 3 phase wire ) for pcc 8.5 mtr and st pole 11mtr long 45 errection of stay complete 46 earthing complete 47 grounting of pcc pole 8.5 mtr long 48 grounting of st pole 11mtr long 49 jointing of 11kv cable box 3x120 mm sq outdoor 50 errection of 11kv ct / pt unit by gi strip 51 cartage of 11kv pilfer unit ( from store to side ) 52 errection of 11kv pilfer unit by gi strip 53 earthing of 11kv ct / pt unit & 33 kv pilfer unit 54 connection of cable jointing kit for st pole, ct / pt unit & pilfer unit 55 laying of cable inter hdpg pipe charges 56 pole painting ( red oxide and alluminium paint ) 57 errection of gaurding 58 hoisting of cable for pole with gi pipe charges 59 pole painting ( red oxide and alluminium paint ) 60 errection of gaurding 61 t / f plinth 62 pale fencing 63 special earthing for t / f netrul & body 64 installation & energization of 100 kva t / f 65 tree branches cutting 66 cartage of all material...

Purvanchal Vidyut Vitaran Nigam Limited - Uttar Pradesh

33015862 o provide power connection under deposit plan of 70 kw to state iti college vill mahgaon, post garthama varanasi work will be done on turnkey basis 2 stp 11mtr long 3 pcc pole 8.5 mtr long 4 acsr dog conductor 5 acsr weasel conductor ( 930x3+3% ) 6 11kv pin insulator 7 11kv pin with nut 8 11kv disc insulator t&c type 45kn 9 11 kv disc fitting t&c type 45kn 10 11 kv v type cross arm ( angle 65x65x6 ) 11 stay complete 1650x15mm 12 earthing complete 13 ms channel 125x65x1300 ( tee off ) 14 ms channel 125x65x2240 ( top ) 15 ms angle 75x75x6x2028 mm with clamp & bolt & nut ( t / f base ) 16 ms channel ( dropper ) 100x50x2028 mm for fuse set 17 guarding cross arm ( ms angle 65x65x6mm ) 18 gi wire 5mm 19 100kva t / f 20 3x120 sq.mm 11kv xlpe cable ( 90x2+20 ) 21 11kv xlpe c / j kit 3x120sq.mm outdoor 22 11kv xlpe c / j kit 3x120sq.mm indoor 23 stone pad 24 holding clamp for top channel 25 x arm holding clamp 26 f bracket 27 clamp for tee off with nut & bolt 28 danger plate with clamp 29 barbed wire 30 guarding clamp for guarding cross arm 31 alluminium paint 32 red oxide paint 33 eye bolt for guard wire 34 nut bolt of various size 35 gi pipe 6 dia 36 hdpe pipe 100mm 37 pipe holding clamp 38 cable holding clamp 39 alumium binding wire 40 erection of work 41 errection and complete fitting of st pole 11mtr long 42 errection and complete fitting of pcc pole 8.5mtr long 43 errection and complete fitting of double pcc8.5 mtr pole 11mtr long 44 sagging of 11 kv line ( 3 phase wire ) for pcc 8.5 mtr and st pole 11mtr long 45 errection of stay complete 46 earthing complete 47 grounting of pcc pole 8.5 mtr long 48 grounting of st pole 11mtr long 49 jointing of 11kv cable box 3x120 mm sq outdoor 50 errection of 11kv ct / pt unit by gi strip 51 cartage of 11kv pilfer unit ( from store to side ) 52 errection of 11kv pilfer unit by gi strip 53 earthing of 11kv ct / pt unit & 33 kv pilfer unit 54 connection of cable jointing kit for st pole, ct / pt unit & pilfer unit 55 laying of cable inter hdpg pipe charges 56 pole painting ( red oxide and alluminium paint ) 57 errection of gaurding 58 hoisting of cable for pole with gi pipe charges 59 pole painting ( red oxide and alluminium paint ) 60 errection of gaurding 61 t / f plinth 62 pale fencing 63 special earthing for t / f netrul & body 64 installation & energization of 100 kva t / f 65 tree branches cutting 66 cartage of all material...

Kisan Sahkari Chini Mills Limited - Uttar Pradesh

32982280 ex godown. supply of berger make industrial paint from reputed suppliers / manufacturers ex godown. supply of berger make industrial paint from reputed suppliers / manufacturers , berger industrial paint , zink chromate red oxide paint , ferrotol no 1 for boiler internal paint , h.r. black chimney paint 700 f temp. stack black , anti corrosive heat resistance off white , black bitumenous paint , h.r. aluminium paint with paste , ferrotol no 3 for boiler external paint , golden yellow , p.o. red , smok greay , bus green , azure blue , enamlled white , g.p. thinner...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32982187 carrying out various deposit works for releasing of new electricity connection / load enhancement to the various consumers at different sites, under deposit scheme, under electricity urban distribution division i, meerut 1 cartage of line material from store to je store and je store to site of work including loading and unloading at both ends. 2 cartage of 09 no. 11 mtr. st pole from store to je store and je store to site of work including loading and unloading at both ends. 3 cartage of 25 / 63 / 100 / 250 kva transformer from store to je store je store to site of work including loading and unloading at both ends. 4 erection of double pole structure including fixing of top chanel dropper chanel, complete in all respect. 5 erection of st pole, complete in all respect. 6 laying, lagging and sagging of acsr weasel conductor. 7 concreting of poles. 8 laying of 11 kv xlpe cable 3x70 sqmm. 9 laying of lt pvc cable 3.5x70 sqmm. 10 fixing of cable jointing kit 3x70 sqmm. 11 water level earthing, complete in all respect. 12 earthing of poles, complete in all respect. 13 cartage of transformer from je to site of work including loading and unloading at both ends. 14 safely fixing of transformer on double pole structure, complete in all respect. 15 fixing of stay, complete in all respect. 16 lt tail less unit with double circuit. 17 lt bus bar box with mccb and meter fixing arrangement. 18 fixing of tpmo, complete in all respect. 19 fixing of fuse set, complete in all respect. 20 fixing of danger board with clamp. 21 stone pad. 22 aluminum paint. 23 red oxide paint. 24 fixing of all types of lugs. 25 fixing of all types of clamps. 26 providing and fixing nuts and bolts. 27 fixing of pin insulator with pin and disk insulator with fitting, complete in all respects. 28 fixing of ms channel all size, compelete in all respect....

Military Engineer Services - Uttar Pradesh

32853518 certain sanction works ( 05 nos ) in age br i and age em under ge babina 1 excavationin trenchesnot exe 1.5 mtrs wideand not exe 1.5 mtr in depth and getting outin any type of soiletc complete all as specified and directed . 2 excavation in post holes ( or similar holes ) each not exc 0.5 cum , getting out in any type of soilsandremoving surplus soil to a distance not exc 50m and as directed. 3 surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard / dense soil comlete all as specified and directed. 4 returning, filling in, including spreading, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified and as directed. 5 removing excavated soils / material to a distance n exc 50m and deposited where directed at a level n. exc 1.5m above the starting point complete all as specified and as directed. 6 m&l for moorum laid in layers n exc 15 cm thickness , spread , levelled , rammed and watering as in floorsetc complete and all as specified 7 m&l for hard core of broken boulders / stone of gauge n exc. 63 mm, deposited, spreading, leveling watering and well ramming to true surface in layers not exceeding 15 cm thick each layer complete all as specified and directed. 8 demolition of brick work / stone masonary built in cement mortar of nay description , any position and anylocation and as direcetd 9 m&l for brick work with fly ash bricks ( fasb ) straight or curved on plan exc 6 m radius built in cement mortar ( 1 : 4 ) etccomplete all as specified and as directed. 10 m&l for pcc 1:3:6 type c 2 using 40mm graded stone agg as in filling and mass concrete , sub base / flooring complete all as specified and directed. 11 m&l for pcc 1:4:8 type d2 using 40mm graded stone aggregatesas in foundation filling etccomplete all as specified and directed. 12 m&l for pcc 1:2:4 type b 2 using 40mm graded stone agg as in filling and mass concrete, sub base / flooring complete all as specified and directed. 13 m & l for pcc work of flexural strength of 40 kg / sqcm using cement 400kg / cumas in pavement , floors & hard standing, laid in panels not exceeding 30 sqm each , panel shall be formed using mild steel members of adequate size and thichness to create 10 mm wide joints , surfaces ofconcrete finished even and fair to desire level etc complete all as specified and as directed. note : ( i ) cost of sample testing for design mixto ensure flexural strength 40 kg / sqcm will be borne by the contractor . min cement content shall be 400 kg / cum of concrete . in case cement required more than 400 kg shall deemed to be included in the quoted rate and nothing extra shall be admissible on this account . ( ii ) joint shall be measured and paid seperately . 14 m&l for filling of contraction joints 10 mm wide x 30 mm deep and tfilled with sealing compound grade a etc complete as directed 15 m & l for precast rcc1:1.5: 3 type a 1 using 20 mm graded stone aggregate as in lintel upto 1.50 mtr span etc complete all as specified and as directed. note : reinforcement shallbe paid seperately 16 s&f, 2nd class hard wood ( sal ) as in scantling, wrought timber frame work as in members of trusses like rafter , purlins etc similar etc complete and as directed. note : the moisture and species test is manadatory prior to used timber and shall be got tested from govt lab or from nibl approved lab . no payment of timber shall be made unless got tested and test results thereof found satisfactory 17 m&l for mild steel tmtbars8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookingends and binding with and includingmild steel wire ( annealed ) not less than 0.9mm dia or securing with clips etc complete all as specified and directed .make : as specified in tender documents 18 s&f mild steel work as in tubular trusses including special shaped washer etc complete using erw or induction butt welded tubes conforming to is 1161 1979 grade st 240 with and including one shop coat of zinc chrominium primer paint complete all as specified and as directed. 19 s&f mild steel work as in roof trusses ( framed ) trussed , purlins , crane gentries rails and fastenings and heavy brackets framing ( beam, tee, angle, channel or flat sections ) incl distance pieces , cleats etc of 290gde e 165 etc complete all as specified and as directed. make : as specified in tender documents 20 s &f mild steel hold flat iron 40x5 mm thick as in wind tie over roof including securing bolts including driling holes etc complete and as directed make : as specified in tender documents 21 s&f mild steel ( plain ) plates , square cut or notched ( ordinary and counter sunk ) forming holes of suitable dia if requiredand fixed to pipe by electric welding alround the neck of pipe etc complete and as directed. 22 s&f mild steel screw bolts ( machine made ) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 10 cm length and 11 to 15 mm dia 23 dismantling of timber scantling 40 sqcm and over in section fixed in any position as framed work complete all as specified and directed 24 taking out / dismantlingof existing roof treatment of any description , any position over roof including taking out plain cement concrete of any description to the thckness as directedetc complete and including lowering down complete waste materials to the ground on a place where directed and includingremoval of the same to a distance exc 250 mtr but n exc 500 mtr as directed .note : the cost of lowering down and removal deemed included in unit rtae quoted by the tenderer. 25 m&l for cutting out cracks to v section in existing roof or terracing , cleaning out , wetting and sealed solidly with hot mixture of bitumen and dry sand in proportion of 1:1 by weight etccomplete and as directed. 26 m&l for cutting grooves in brick wall 75mm wide and 65mm deep and shaping horizontal face of groove sealed with cement mortar 1:3 complete and as directed. 27 m&l for p.c.c 1:2:4 type b 1 using 20 mm graded stone aggregate as in padding laid to slope over roof and surface finished even and fairetccomplete all as specified and as directed. note : the thickness of pcc shall not be exceeded more than75 mm at any place 28 m&l for p.c.c 1:2:4 type b 0 using 12.5 mm graded stone aggregate as incoping andon roof etccomplete all as specified and as directed. 29 supply only water roofing compound ( liquid ) isi marked etc complete and as directed 30 m&l for 10 mm thick rendering in cement mortar 1:4 on concretesurfaces of roof when concrete is stillgreen mixed withwater proofing compound ( liquid ) @ 200 ml perbag of cement of 50 kgs , surface finished even and fair enough to receive water proofing traetment etc complete all as specified and as directed. note : wpc shall be measured and paid seperately 31 m&l for providingwater proofing treatment over roof by applying the following operations : ( a ) preparation of plastered surface by cleaningwith water and leave the sufaces till to become surface total dry . ( b ) applyingfirst coat of bitumen primer conforming to is 3384 @ 0.4kg / sqm on plastered surface ( c ) applying app based polymeric membrane 3mm thick ( minimum thickness ) and weightnot less than 3kg / sqm , reinforced with polyester non woven fabric ( wt not less than 150 gms / sqm ) over on primed surfacelaid with 100mm side lap / end lap on prepared surfaces as per manufacturers instructions and under strict supervision of manufacturers tenchnical representativeetc and applying two coats of bituminous based aluminum paint @ 100 ml / sqm each coat etc complete and as directed. note : testing of app membrane is mandatory and contractor will not be allowed to carry out the work untill results are obtained and found satisfactory .cost of testing and samples ( 3nos ) deemed to be included in unit rate quoted by thetendrer and nothing extra on this account will be admissible . ( ii ) the cost of casting onecement plate of size 600 mm x 450 mm , 10 mm thick rendering in cm 1:3 in each building incl writing materials shall deemed to be included in the unit rate quoted by the tenderer. 32 m &l for plain concrete cement tiles ( cement ) 30cm x 30cm x 25mm set and jointed and pointedin neat cement slurry on roof over & including 15mm thick screed bed in cm ( 1: 4 ) and joint between the tiles to be filled with chemiucal like grout etc complete all as specified and directed. 33 dismantling wall / ceiling boards of any description any thickness incl exiting snap grid framework of any descriptionand as directed. 34 m&l for snap grid ( 600 x600 mm ) ceiling using aluminium anodised sectionsie main tee section of 36.5x25x1.4mm size ( wt not less than 0.24kg / rm ) , wall angle of size 40x25x2mm size ( wt not less than 0.36kg / rm ) , cross tee section 23.5x26.4x1.4mm size ( wt not less than 0.191kg / rm ) andsnap grid shall be fixed to ceiling by supporting hangers consisting of 6 mm dia mild steel bar made to shape including providing mild steel flat iron cleat with 40x3 mm and fixed with expansion dash fastener n exc 1.20 mtr both ways fixed to roof etccomplete all as directed. 35 m&l for for 4 mm thick high pressure steam cured non asbestos fiber cement designer board of size 600mm x 600mm as in ceiling complete all as specified and directed with and including aluminium anodised snap grid frame. 36 dismantling asbestos cement , galvalume , fibre sheet ( plain , corrugated , semi corrugated ) and as direcetd 37 s&f pre painted galvalume aluminium zinc coating gi based corrugated steel sheet 0.50mm thickcolouredhaving tensile strength of 550 mpa as in roof covering andfixed with self tapping screws and as directed . 38 s&f pre painted galvalume aluminium zinc coating gi basedplain steel sheet 0.50mm thickcolouredhaving tensile strength of 550 mpa as in cladding / wall fixed with self tapping screws and as directed . 39 m&l for 75 mm thick p.c.c 1:3:6 type c 1 using 20 mm graded stone aggregate as in plinth protection laid in alternate panels made of 10 mm thick plywood ( size of each panel shall not exceed 12 sqm ) and finish the surface even and smooth withoutusing extra cement including filling of jointwith bitumen mastic ( 1 part bitumen mixed with 3 part dry sand ) etc complete all as specified and as directed. note : cost of form work for forming joints and jointing materials deemed to be included in unit rate quoted by the tenderer. 40 m&l for non skid ceramic coloured tiles 7 to 8 mm thick ( square / rectengular ) dark ( premium quality ) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurryand pointed in white or coloured cement to match over 15 mm thick screed bed in cm 1:6 etccomplete all as specied and directed. 41 m&l glazed ceramic coloured tilesdark ( premium quality ) 7 to 8 mm thick size 300x600 mm joint free over 15 mm thick rendering in cement mortar 1:4 in skirting / dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed . 42 taking down cement plaster of any description built in cement mortar on brick or stone walls etc including racking out joints, hacking for key, scrubbingdown with water etc.complete all as specified. 43 m & l for 15 mm thick rendering in cement mortar 1: 6 on fair faces of brick work or concrete surfaces , surface finished even and smoothwithout using extra cement complete all as specified and as directed. 44 m & l for 15 mm thick rendering in cement mortar 1: 6 on other than fair faces of brick work or stone masonary , surface finished even and smoothwithout using extra cement complete all as specified and as directed. 45 m & l for prepration of newly plastered surfaces of walls appying two coat of cement base paint over a coat of primeretc complete all as specified and as directed . 46 m & l for complete removal of existing treatment from walls and appying two coat of cement base paint over a coat of alkali resistant primerincluding necessary prepration of surface complete all as specified and as directed. 47 m & l for applying two coat of white wash on wallsincludingnecessary preparation ofsurfaces all as specified and directed. 48 m&l for preparation of old decorated surfaces of wall including cornices, plastered or unplastered surfaces by brooming down or steel wire brushing to remove dust, dirt and loose scales of lime wash and other foreign material etc and applying two coat of white wash complete all as specifiedand directed. 49 m&l for preparing new surfaces of steel of any description, over 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paints over one coat of red oxide primer all as specified. 50 s&f 100 mm bore cast iron soil waste and vent pipe spun pipein any length with or without ear and jointed in cm 1:1 fixed to wallswith ms clamp made of flat iron 50x5 mm and bolt grouted in wall withpcc 1:2:4 type b 0 using 12.5 mm graded stone aggregates and taking out existing pipe of any description etc complete all asspecified and directed. 51 s&f cast iron bend any radius 100 mm bore etc compete and as directed 52 taking up or down existing steel tubing and connections including cleaning for refixing etc complete all as specified and as directed for 15 mm bore 53 taking up or down existing steel tubing and connections including cleaning for refixing etc complete all as specified and as directed for 20 mm bore 54 supplying, fixing, jointing and testing 15 mm dia galvanised iron tubing medium grade isi marked with all fitting such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete all as specified and as directed 55 supplying, fixing, jointing and testing 20 mm dia galvanised iron tubing medium grade isi marked with all fitting such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete all as specified and as directed 56 taking down old existing unserviceable tank pvc ( hdpe ) and of capacity exc250 ltrs but n exc 500ltrs complete as direcetd 57 s&f 500 ltr capacity or rotational moulded polyethylene water storage tank ( cylindrical vertical with closed top ) white , isi marked , triple layered construction hoisted and fixed in position including s&f 20mm dia gi pipe medium grade washout pipe 450mm long with plug and 20mm dia gi pipe medium grade overflow pipe 600mm long with fitting etc complete all as specified in ssr part i 2009 complete all as specified and as directed. 58 s & fball valve highpressure of ptmt with epoxy coated aluminium rod & highdensityplastic ball screwed for iron pipe 20 mm dia and fixed in new tank ( minimum weight 20mm 210 gm ) complete all as specified. 59 s & f in repairs ball valve highpressure of ptmt with epoxy coated aluminium rod & highdensityplastic ball screwed for iron pipe 20 mm dia and fixed in new tank ( minimum weight 20mm 210 gm ) complete all as specified. 60 s&f20 mm gun metal gate valve ( isi marked ) with iron wheel head screwed both ends for iron pipe etc complete as directed. 61 s&fin repair 20 mm gun metal gate valve ( isi marked ) with iron wheel head screwed both ends for iron pipe etc complete as directed. 62 demolition of cement concrete ( unreinforced ) inground floors and paving n. exc 15 cm thickness below or above ground level complete all as specified and as directed. 63 taking down carefully aluminium / copper point wiring on battenor in pvc conduit or in ms conduit with gi earth wire etc ( for light, fan, socket or power point ) complete , including taking out fixtures and fittings such as switches , ceiling roses, pendents, regulators , sockets, light fitting etcremoving materials to store for keeping in safe custudy or for taking credit ( as per schedule of credit for dismantled / taken out items ) and making goodthe disturbedsurfaces of walls, floors, ceilings etc and as directed . 64 taking down carefullyexisting wooden board , main switch, mcb db boxes, tpn boxes, cut out, etc of any size anycapacity fromboards completeall as specified and as directed. 65 taking down carefully sub main wiring with any cable / service connection twin core from wall / lt pole of any size of aluminum with wooden batten and or through rigid conduit including gi wire and making good the disturbed surfaces of walls, roofs, floors etc complete all as specified and as directed. 66 m & l for surfacepoint wiring ( inpvc conduit ) one light pointcontrolled by one switch with pvc insulated and unsheathed flame retardant low smoke ( frls ) cable of 1.5 sqmm ( nominal area ) with stranded copper conductor single core 1100 volts grade in and including non metelic rigid pvc conduit not less than 19 mm dia, clip, withms terminal boxes ( not less than 1.6mm thick ) including earth dollywithframe plates with matching cover plates all modules including 1.5 sqmmstranded copper conductor green as continuous earth wire with lugs complete all as specified and as directed . note : quoted rates shalldeemed to be inclusive for provision of covering sunken boards / terminal boxes / junction boxes of any shape and size with 3mm thickisi marked hylam sheet / backlite sheet cover fixed with suitable brass screws and cup washers. 67 all as per srl item no. 66 above but one fan / exhaust point controlled by oneswitch ®ulator. 68 all as per srl item no.66 above but one 3 / 5 pin5 amp socket outlet point controlled by oneswitch on independent board. 69 all as per srl item no.66 above but one 3 / 5 pin5 amp socket outlet point controlled by oneswitch on same board. 70 description all as per item no 66above but for power point wiring using 2.5 sqmm single core multi stranded copper conductor pvc insulated and unsheathed, flame retardant low smoke ( frls ) cable for 3 / 6 pin 15 amp socket outlet controlled by one switch on independent board with and including 1.5 sqmmstranded copper conductor green as continuous earth wire with lugs complete all as specified and as directed. 71 m & l for concealedpoint wiringone light pointcontrolled by one switch with pvc insulated and unsheathed flame retardant low smoke ( frls ) cable of 1.5 sqmm ( nominal area ) with stranded copper conductor single core 1100 volts grade in and including non metelic rigid pvc conduit not less than 19 mm dia, clip, withms terminal boxes ( not less than 1.6mm thick ) including earth dollywithframe plates with matching cover plates all modules including 1.5 sqmmstranded copper conductor green as continuous earth wire with lugs complete all as specified and as directed .note : ( i ) quoted rate shall be deemed to include the cost of cutting chases in walls / pillars / column etc. of any description for concealing the conduit to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. the portion of point wiring at ceiling shall be in surface pvc conduit / casing & caping of suitable size as directed fixed on ceiling surface with using pvc rawl plugs. ( ii ) fittings like switches, sockets, regulators, lamp holders, light fittings shall be measured and paid for separately under appropriate item of schedule `a. ( iii ) the quoted rates shall be deemed to be inclusive for provision of covering sunken boards / terminal boxes / junction boxes of any shape and size with 3mm thickisi marked hylam sheet / backlite sheet cover fixed with suitable brass screws and cup washers 72 all as per srl item no. 71 above but one fan point controlledby oneswitch ®ulator. 73 all as per srl item no.71 above but one 3 / 5 pin5 amp socket outlet point controlled by oneswitch on independent board. 74 all as per srl item no.71 above but one 3 / 5 pin5 amp socket outlet point controlled by oneswitch on same board. 75 description all as per item no 71above but for power point wiring using 2.5 sqmm single core multi stranded copper conductor pvc insulated and unsheathed, flame retardant low smoke ( frls ) cable for 3 / 6 pin 15 amp socket outlet controlled by one switch on independent board with and including 1.5 sqmmstranded copper conductor green as continuous earth wire with lugs complete all as specified and as directed. 76 s & f switch piano flush button type10 amp, single pole , one way , ac , 230 volts , 50 hz complete all as specified and asdirected. 77 s&fsocket outlet 2in 1 , 3 pin , 10 amp , ac , 230 volts , 50 hzcomplete all as specified and asdirected. 78 s & f switch piano flush button type 20 amp, single pole, one way , ac , 230 volts , 50 hz complete all as specified and asdirected. 79 s & fsocket outlet 2 in 1, 10 amp and 20 amp, ac , 230 volts , 50 hz complete all as specified and asdirected. 80 s & fdelux fanregulator rotary, step type , ac , 240 volts , 50 hz complete all as specified as directed. 81 s & flamp holder, pvc / urea type with back plate , ac , 230 volts , 50 hz , isi marked suitable for batten fittingscomplete all as specified as directed 82 s&f ceiling rose, surface bakelite 65 x50mm three brass terminals, ac , 230 volts , 50 hz isi marked completeall as specified and asdirected. 83 s & f9 / 10w led retrofit ball lamp holder base b 22, bipin type ac 230 volts 50 hz with pf not less than 0.95 with polycorbonate body and aluminium heat sink complete all as specified as directed. 84 s&f for sub main wiring with pvc insulated, unsheathedflame retardant low smoke ( frls ) 2 single core cable 1100 volts grade withcopperconductor of size 10 sq mm ( nominal area ) multi stranded drawn into new non rigid metellic pvc conduit with and including 6 sqmm green stranded copper conductor as contineous earthwire withlugs complete all as specified and as directed. note:two run of single core pvc cable with one run of earth conductor cable and conduit shall be measured as one unit. ( ii ) cost of new pvc conduit including conduit accossoriesshall be deemed to be included in unit rate quoted by the tenderer . 85 s&f for sub main wiring with pvc insulated, unsheathedflame retardant low smoke ( frls ) 2 single core cable 1100 volts grade withcopperconductor of size 6 sq mm ( nominal area ) multi stranded drawn into new non rigid metellic pvc conduitwith and including 4 sqmm green stranded copper conductor as contineous earthwire withlugs complete all as specified and as directed. note:two run of single core pvc cable with one run of earth conductor cable and conduit shall be measured as one unit. ( ii ) cost of new pvc conduit including conduit accossoriesshall be deemed to be included in unit rate quoted by the tenderer . 86 s&f tpn db dpx 125 mccb dbs 4 way double door with provision for dpx 125 mccb and as incomer and sp / tp mcbs as out going no of modules dpx 125 + 12 etc complete all as specified and directed. 87 s&f mccb , 200amps, 415 volts, 4 p , 50hz, having 36 ka rupturing capacitywith electronic trip arrangment and setting screw upto 70% including making connection with excisting cable with connection and materials like copper strips, lugs, nut & bolts etc. complete all as specified and as directed . 88 s&f mccb , 100amps, 415 volts, 4 p , 50hz, having 25 ka rupturing capacitywith electronic trip arrangment and setting screw upto 70% including making connection with excisting cable with connection and materials like copper strips, lugs, nut & bolts etc. complete all as specified and as directed . 89 s&f mccb , 63amps, 415volts, 3 phase, 50hz, having 35 ka rupturing capacity, 415 volts with electronic trip arrangment and setting screw upto 70% including making connection with excisting cable with connection and materials like copper strips, lugs, nut & bolts etc. complete all as specified and as directed . 90 s&f mccb , 63amps, 415volts, 3 phase, 50hz, having 16 ka rupturing capacity, 415 volts with electronic trip arrangment and setting screw upto 70% including making connection with excisting cable with connection and materials like copper strips, lugs, nut & bolts etc. complete all as specified and as directed . 91 s&f sheet metal enclosure box with hinges door suitable for mccb 63 amp to 100 amp with all necessary fixing arrangementetc for walletc. complete all as specified and as directed . 92 s&fsheet metal enclosure double door concealed suitable for distribution boards when mcbs to be used having 100amp rated bus bar 8 ways 240 v complete all as specified and as directed. 93 s&fmcb single pole and neutral 40 amp 240 v , 10ka , c series, isi marked complete all as specified and as directed with copper lugs. 94 s&fmcb single pole and neutral 63 amp 240 v , 10ka , c series, isi marked complete all as specified and as directed with copper lugs. 95 s&fmcb tpn 63 amp 240 v , 10ka , cseries, isi marked complete all as specified and as directed with copper lugs. 96 s&fmcb single pole 6 to 32amps 240 v, 10ka, c series, isi markedcomplete all as specified and as directed with copper lugs. 97 s&fin repairs 20 w led, 6000k decorative ultra slim linear fitting , extruded aluminium , environmental friendly, energy efficient incl 20 w lamp fitted incl wiring upto and terminating into existing ceiling rose complete all as specified and as directed. 98 s&f 36w 2x2 led fitting ultra mordern ceiling mounted luminaire suitable for armstrong / grid ceiling in ms housing with high brightness leds incl wiring upto and terminating into existing ceiling rose. 99 s&f wall mountedfan 600 mm sweep turbo force aerodynamic desined blade for high air deleivery complete incl all necessary fixing arrangements and as directed. 100 s&f ceiling fan 1200mm sweep bee ratedac single phase 230 volts etc connecting with flexible cable 3 core copper conductor of size 23.0 / 0076 of suitable length from celling rose complete all necessary arrangement of hanging of celling fan ( gi pipe hook etc ) as specified and as directed. 101 s & f exhaust fan, ac , singe phase , 230 / 240 volts , 300 mm sweep , noiseless light weight rust proof steel body self closing louvers and blades, speed1400complete with all arrangement of making hole complete all as specified and as directed. 102 s&f for replacement & testing commissioning of outdoor type bus bar panel padestel type weather proofms cubical panelboard made of3 mm crca ms sheet , size 110 cm x 80 cm x 40 cm, 4 nos of aluminium bus bar of 500 amp capacity including providing mccb , 4 pole , 320 amp , repturing capacity35 ka , adjustable type ( ics =icu=100% ) including one coat of redoxide and two coat of enamel paint powder coated, mounted on mild steel channel of suitable sizeand providing pcc work inpcc1:3:6 type c 2, 60 cm height above gl over 300 mm thick pcc 1:4:8 type d 2 ( using 40mm graded crushed stone aggregate ) in foundation for fixing panels & aluminium busbar chanel insulated with colour coated heat shrinkable sleaves and mounted on dmc / epoxy insulator all as specified & directed. 103 s&fnew generation energy saving and environmental friendly long life led flood light made up of innovative die cast aluminium housing high power led as lighting source with ip 66 power consumption 30 watt complete input voltage of 150 240 volt ( nominal rated voltage 240 volt ) completeall as specified and directed. 104 s&f in replacement new generation security light fitting 1 x 36 w led , envoirnmental friendly long life , made up of of innovative die cast aluminium housingwith high power led as light source withip 66 protection , power consumption 45 watt complete input voltage of 150 240 volt ( nominal rated voltage 240 volt ) includingelectric connection with1.5 sqmm 3 core pvc insulated and pvc sheathed cable stranded copper conductor from junction box to security light etc complete as specifiedand as directed. 105 supplying , laying & testing in replacement cablexlpe insulatedscreenedpvc bedded armoured with galvanised steel wire or tape, electric power cable heavy duty 1100 volt gradealuminium conductor of size 50x3.5coreincluding taking out acsr / ug cable from any location etc complete all as directed. etc complete all as directed. 106 supplying , laying & testing in replacement cablexlpe insulatedscreenedpvc bedded armoured with galvanised steel wire or tape, electric power cable heavy duty 1100 volt gradealuminium conductor of size25x3.5coreincluding taking out acsr / ug cable from any location etc complete all as directed. etc complete all as directed. 107 supplying , laying & testing in replacement cablexlpe insulatedscreenedpvc bedded armoured with galvanised steel wire or tape, electric power cable heavy duty 1100 volt gradealuminium conductor of size25x 4coreincluding taking out acsr / ug cable from any location etc complete all as directed. etc complete all as directed. 108 supplying , laying & testing in replacement cablexlpe insulatedscreenedpvc bedded armoured with galvanised steel wire or tape, electric power cable heavy duty 1100 volt gradealuminium conductor of size16 x 4 coreincluding taking out acsr / ug cable from any location etc complete all as directed. etc complete all as directed. 109 excavationin trenches in any type of soil not exe 1.5 mtrs wideand not exe 1.5 mtr in depth for laying of pipe / cables etc and getting out incl forming bottom surface to the required level / slope etc complete all as specified and directed . 110 m&l for dry clean sand free from sharp materialsfor cushioning laid in trenches in layers forunder ground electric cablecomplete all as specified and directed 111 supplying and laying precast concrete cable cover class lv type i flat size 250x150x40 mm laid parpendicular to the axis of cable in trenches etc complete as directed. 112 supplying and laying gi pipe 50 mm bore medium grade including providing fittings such as elbow, tee, socket etclaid on floors / trenches / walls with complete fixing arrangements and testing etccompleteall as specified and directed . 113 m&l for earthing completewith galvanisedsteelearth plateelectrode of size 600 mm x 600 mm x 6 mm thick weight n less than 17.25 kgs buried directly in ground ( earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by gi pipe 15 mm bore ( light grade ) and watering pipe 20 mm bore gi pipe ( light grade ) andchamber of pcc 1:4:8 type d2 using 40 mm graded stone aggregate and coping shall be in pcc 1:3:6 type c1 using 20mm graded stone agg.50 mm thick cover of rcc 1:2:4 type b1 using 20 mm graded stone agg. reinforced with 8 mm dia ms tor bar @ 80 mm c / c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of ssr pt i ( 2009 ) with charcoal dust and saltcomplete and earth leadconnected to earthing test point ( up to main switches, dbs ) completeall as specified &testing on completion. note: ( i ) item includes the cost of 7.5 mtr length gi pipe for protection for gi earth wire. ( ii ) item rates includes the cost of 7.5 mtr earth lead gi earth wire. ( iii ) pcc pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra costof additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate. 114 m&l for earthing completewith galvanisedsteelearth plateelectrode of size 600 mm x 600 mm x 6 mm thick weight n less than 17.25 kgs buried directly in ground ( earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead strip of size 32x6 mm thick by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by gi pipe 15 mm bore ( light grade ) and watering pipe 20 mm bore gi pipe ( light grade ) andchamber of pcc 1:4:8 type d2 using 40 mm graded stone aggregate and coping shall be in pcc 1:3:6 type c1 using 20mm graded stone agg.50 mm thick cover of rcc 1:2:4 type b1 using 20 mm graded stone agg. reinforced with 8 mm dia ms tor bar @ 80 mm c / c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of ssr pt i ( 2009 ) with charcoal dust and saltcomplete and earth leadconnected to earthing test point ( up to main switches, dbs ) completeall as specified &testing on completion. note: ( i ) item includes the cost of 7.5 mtr length gi pipe for protection for gi earth wire. ( ii ) item rates includes the cost of 7.5 mtr earth lead gi earth wire. ( iii ) pcc pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra costof additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate....

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32837277 tender for electrification work 1 supply & erection 2 11 m long stp ( galvanized ) 3 pcc pole 8.5 m long 4 stone pad 300x300x75 mm 5 x arm m.s. angle 65x65x6 mm, v type 11 kv 6 clamp for channel & x arms holding clamp with bolts & nuts 7 11 kv pollymer pin insulator 8 f bracket with bolts & nuts 9 phase wire 30 sqmm acsr weasel 10 alluminium winding wire 6 swg 11 alluminium jointing sleeves for acsr weeasel 12 danger board with clamp for 11 kv 13 painting number mark with paint 14 barbed wire 15 red oxide 16 alluminium paint 17 stay rod 16x1800 mm 18 stay wire gi ( 7 / 3.15 mm ) 7 / 10 swg 19 11 kv stay insulator 20 11 kv stay clamp for stp pole 21 earthing of poles ms earthing rod of 20x2500 mm and 6 swg earthing wire etc 22 t off channel 23 clamps with bolt & nut for channel 24 11 kv disc insulator 25 11 kv disc fitting 26 e bracket 27 ms angle 65x65x6 mm, 2700 mm long bracing with clamp 28 top channel 100x50x2240 mm ( 10.70 kg / m ) 29 11 kv disc insulator 45 kn 30 e bricket 31 pg clamps 32 bolts, nuts & washers 33 gaurding angle 50x50x5x2250 mm 34 clamp for gaurding angle stp pole 35 eye bolt 12x100 mm2 36 g.i. wire no 6 swg 37 g.i. wire no 8 wg 38 3x120 mm2 11 kv xlpe cable 39 i / d & o / d cable jointing kit suitable for 11 kv 3x120 mm2 xlpe cable 40 m.s. channel dropper 100x50x2028 mm 41 11 kv tpmo 42 11 kv fuse set 43 lt pvc cable al. 3.5x400 sqmm 44 lt pvc cable al 1x240 sqmm 45 al. leg long barrel off size ( ls ) 46 4 core lt mcb with box ( ls ) 47 m.s. angle 75x75x6x2028 mm 48 cost of g.i. pipe 32 mm dia 49 cost of copper wire 6 swg 50 copper bond 51 make hold of size 18 mm dia in gi pipe 52 11 kv switchgear i / c 600 / 300 / 5a 350 mva 53 11 kv switchgear o / c 200 / 100 / 5a 350 mva 54 11 kv 3 core cable 185 mmsq xlpe 55 11 kv 3 core cable 120 mmsq xlpe 56 11 kv cable jointing kit 185 sqmm ( indoor & outdoor ) 57 11 kv cable jointing kit 120 sqmm ( indoor & outdoor ) 58 24 volt battery and battery charger with cabinet 59 control cable 4x2.5 mmsq 60 control cable 2x2.5 mmsq 61 grouting of pole...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32837274 tender for electrification work 1 supply & erection 2 11 m long stp ( galvanized ) 3 pcc pole 8.5 m long 4 stone pad 300x300x75 mm 5 x arm m.s. angle 65x65x6 mm, v type 11 kv 6 clamp for channel & x arms holding clamp with bolts & nuts 7 11 kv pollymer pin insulator 8 f bracket with bolts & nuts 9 phase wire 30 sqmm acsr weasel 10 alluminium winding wire 6 swg 11 alluminium jointing sleeves for acsr weasel 12 danger board with clamp for 11 kv 13 painting number mark with paint 14 barbed wire 15 red oxide 16 alluminum paint 17 stay rod 16x1800 mm 18 stay wire gi ( 7 / 3.15 mm ) 7 / 10 swg 19 11 kv stay insulator 20 11 kv stay clamp for stp pole 21 earthing of poles ms earthing rod of 20x2500 mm and 6 swg earthing wire etc 22 t off channel 23 clamps with bolt & nut for channel 24 11 kv disc insulator 25 11 kv disc fitting 26 e bracket 27 ms angle 65x65x6 mm, 2700 mm long bracing with clamp 28 top channel 100x50x2240 mm ( 10.70 kg / m ) 29 11 kv disc insulator 45 kn 30 e bricket 31 pg clamps 32 bolts, nuts & washers 33 gaurding angle 50x50x5x2500 mm 34 clamp for gaurding angle stp pole 35 eye bolt 12x100 mm2 36 g.i. wire no 6 swg 37 g.i. wire no 8 wg 38 3x120 mm2 11 kv xlpe cable 39 i / d & o / d cable jointing kit suitable for 11 kv 3x120 mm2 xlpe cable 40 m.s. channel dropper 100x50x2028 mm 41 11 kv tpmo 42 11 kv fuse set 43 lt pvc cable al. 3.5x400 sqmm 44 lt pvc cable al 1x240 sqmm 45 al. leg long barrel off size ( ls ) 46 4 core lt mcb with box ( ls ) 47 m.s. angle 75x75x6x2028 mm 48 cost of g.i. pipe 32 mm dia 49 cost of copper wire 6 swg 50 copper bond 51 make hold of size 18 mm dia in gi pipe 52 grouting of pole...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32837263 tender for electrification work 1 supply & erection 2 11 m long stp ( galvanized ) 3 pcc pole 8.5 m long 4 stone pad 300x300x75 mm 5 x arm m.s. angle 65x65x6 mm, v type 11 kv 6 clamp for channel & x arms holding clamp with bolts & nuts 7 11 kv pollymer pin insulator 8 f bracket with bolts & nuts 9 phase wire 30 sqmm acsr weasel 10 alluminium winding wire 6 swg 11 alluminium jointing sleeves for acsr weasel 12 danger board with clamp for 11 kv 13 painting number mark with paint 14 barbed wire 15 red oxide 16 alluminum paint 17 stay rod 16x1800 mm 18 stay wire gi ( 7 / 3.15 mm ) 7 / 10 swg 19 11 kv stay insulator 20 11 kv stay clamp for stp pole 21 earthing of poles ms earthing rod of 20x2500 mm and 6 swg earthing wire etc 22 t off channel 23 clamps with bolt & nut for channel 24 11 kv disc insulator 25 11 kv disc fitting 26 e bracket 27 ms angle 65x65x6 mm, 2700 mm long bracing with clamp 28 top channel 100x50x2240 mm ( 10.70 kg / m ) 29 11 kv disc insulator 45 kn 30 e bricket 31 pg clamps 32 bolts, nuts & washers 33 gaurding angle 50x50x5x2500 mm 34 clamp for gaurding angle stp pole 35 eye bolt 12x100 mm2 36 g.i. wire no 6 swg 37 g.i. wire no 8 wg 38 3x120 mm2 11 kv xlpe cable 39 i / d & o / d cable jointing kit suitable for 11 kv 3x120 mm2 xlpe cable 40 m.s. channel dropper 100x50x2028 mm 41 11 kv tpmo 42 11 kv fuse set 43 lt pvc cable al. 3.5x400 sqmm 44 lt pvc cable al 1x240 sqmm 45 al. leg long barrel off size ( ls ) 46 4 core lt mcb with box ( ls ) 47 m.s. angle 75x75x6x2028 mm 48 cost of g.i. pipe 32 mm dia 49 cost of copper wire 6 swg 50 copper bond 51 make hold of size 18 mm dia in gi pipe 52 33 kv v type cross arm 53 33 kv xarm holding clamp with bolts & nuts 54 33 kv f bracket with bolt & nuts 55 33 kv pin insulator 56 33 kv pin with nuts 57 armour rod with ferrule dog 58 alluminium binding wire 59 earth wire with bolt & nuts 60 11 kv switchgear i / c 600 / 300 / 5a 350 mva 61 11 kv switchgear o / c 200 / 100 / 5a 350 mva 62 11 kv 3 core cable 120 mm sq xlpe 63 11 kv cable jointing kit 185 sqmm ( indoor & outdoor ) 64 11 kv cable jointing kit 120 sqmm ( indoor & outdoor ) 65 24 volt battery and battey charger with cabinet 66 control cable 4x2.5 mmsq 67 control cable 2x2.5 mmsq 68 grouting of pole...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32829889 edck 32 / 2022 23 edck 32 / 2022 23 , erection of double pole on s.t. pole including the work of complete line s.t. pole 11 mtr. sp 55 including earthing, grouting & muffling on pole. , laying, sagging, stringing, binding, jointing & jumpering acsr dog conductor , providng & fixing danger board with clamp at vendors cost , providng & fixing number plate with clamp at vendors cost , providing & fixing of gi barbed wire at vendors cost , fixing of ms dropper channel ( 100x50x2028 mm ) , providing & fixing of stone pad 300x300x75mm at vendors cost , providing & fixing of clamp for double pole at vendors cost , providing red oxide paint at vendors cost , providing alluminiumpaint at vendors cost , painting of st pole with red oxide & alluminium paint as per respo noms , providing & fixing of 11 kv tpmo at vendors cost , providing & fixing of 11 kv fuse set at vendors cost , erection of stay rod complete ( g.i 16x1800mm ) , fixin of 11 kv cable j / k 3x185sqmm i / d , providing & laying gi pipe 6 dia at vendors cost , providing & fixing of pg clamp at vendors cost , providing & fixing of 11 kv cable j / k straight through 3x185sqmm o / d at vendors cost , fixing of 11 kv cable j / k 3x185 sqmm o / d , providing of nut bolt off size at vendors cost , cable trench 1 ( 115mx1.68x.5m ) and 2 ( 70mx1.02mx.5m ) at vendors cost , laying of 11 kv xlpe cable including sands and bricks at vendors cost , plinth of t / f for 100 kva ( 2mx2mx1.5m ) at vendors cost , ms strip ( 50x6mm ) fencing size 2.5mx2.5mx1.82m ( 6 feet height including civil work ) at vendors cost , interlocking tiles inside t / f fencing at vendors cost , earthing of t / f for body and neutral at vendors cost , providing & fixing of alluminium lug 185 sqmm at vendors cost , charges from dismantling work: work includes dismantling from site and cartage of same materials from site / location to central store / any other plcace as per instructions of je / sdo / ee concerned. , acsr conductor scrape , 11 kv xlpe 3x185 sqmm scrape , iron scrpae ( 12 no. pole and top dropper etc. ) ...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32749229 tender for electrification work 1 supply & erection 2 13 m long stp ( galvanized ) 3 11 m long stp ( galvanized ) 4 pcc pole 8.5 m long 5 stone pad 300x300x75 mm 6 x arm m.s. angle 65x65x6 mm, v type 11 kv 7 clamp for channel & x arm holding clamp with bolts & nuts 8 11 kv pollymer pin insulator 9 f bracket with bolts & nuts 10 phase wire 30 sqmm acsr weasel 11 alluminium winding wire 6 swg 12 alluminum jointing slleves for acsr weasel 13 danger board with clamp for 11 kv 14 painting number mark with paint 15 barbed wire 16 red oxide 17 alluminium paint 18 stay rod 16x1800 mm 19 stay wire gi ( 7 / 3.15 mm ) 7 / 10 swg 20 11 kv stay insulator 21 11 kv stay clamp for stp pole 22 earthing of pole ms earthing rod of 20x2500 mm and 6 swg earthing wire 23 t off channel 24 clamps with bolt & nut for channel 25 11 kv disc insulator 26 11 kv disc fitting 27 e bracket 28 m.s. angle 65x65x6 mm, 2700 mm long bracing with clamp 29 top channel 100x50x2240 mm ( 10.70 kg / m ) 30 11 kv disc insulator 45 kn 31 e bricket 32 pg clamps 33 bolts, nuts & washers 34 gaurding angle 50x50x5x2500 mm 35 clamps for gaurding angle stp 36 eye bolt 12x100 mm2 37 g.i. wire no 6 swg 38 g.i. wire no 8 swg 39 3x120 mm2 11 kv xlpe cable 40 i / d & o / d cable jointing kit suitable for 11 kv 3x120 mm2 xlpe cable 41 11 kv ct / pt pole mounted combined unit ( ct ration 20 / 5 amp & pt ration 11 kv / 110 v ) 42 meter box for installation 11 kv / 110 volt tvm 11 kv 43 3 phase 4 w static tvm 11 kv 44 11 kv pilfer proof mertering cubible with ct ration 20 / 5 amp & pt ration 11 kv / 110 volt 45 m.s. angle channel dropper 100x50x2028 mm 46 11 kv tpmo 47 11 kv fuse set 48 lt pvc cable al. 3.5x400 sqmm 49 lt pvc cable al 1x240 sqmm 50 al leg long barrel of size ( ls ) 51 4 core lt mcb with box ( ls ) 52 m.s. angle 75x75x6x2028 mm 53 cost of gi pipe 32 mm dia 54 cost of copper wire 6 swg 55 copper bond 56 make hold of size 18 mm dia in g.i. pipe 57 33 kv x arms holding clamp with bolts & nuts 58 33 kv f bracket with bolts & nuts 59 11 kv switchgear i / c 600 / 300 / 5a 350 mva 60 11 kv switchgear o / g 200 / 100 / 5a 350 mva 61 11 kv 3 core cable 185 mm sq xlpe 62 11 kv 3 core cable 120 mm sq xlpe 63 11 kv cable jointing kit 185 sqmm ( indoor & outdoor ) 64 11 kv cable jointing kit 120 sqmm ( indoor & outdoor ) 65 24 volt battery and battery charger with cabinet 66 control cable 4x2.5 mm sq 67 control cable 2x2.5 mm sq 68 grouting of pole...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32747207 tender for electrification work 1 supply & erection 2 13 m long stp ( galvanized ) 3 pcc pole 9.0 m 4 stone pad 300x300x75 mm 5 danger board with clmp for 11 kv 6 barbed wire 7 red oxide 8 alluminium paint 9 earthing of pole ms earthing rod of 20x2500 mm and 6 swg earthing wire 10 ms angle 65x65x6 mm, 2700 mm long bracing with clamp 11 11 kv disc insulator 45 kn 12 disc fitting for dog 13 bolts, nuts & washer 14 33 kv gaurding angle 65x65x6x3500 mm 15 clamp for gaurding angle stp pole 16 eye bolt 12x100 mm2 17 g.i. wire no. 6 swg 18 g.i. wire no. 8 swg 19 xlpe cable 3x300 sqmm for 33 kv line ( 3.25 km double ckt ) 20 staright through jointing kit for xlpe cable 3x300 sqmm 21 outdoor joint kit for xlpe cable 3x300 sqmm 22 gi pipr 6 dia 23 hdpe pipe 140 mm 24 ms channel dropper 125x65 mm, 3200 25 cost of gi pipe 32 mm dia 26 cost of copper wire 6 swg 27 copper bond 28 make hold of size 18 mm dia in gi pipe 29 33 kv v type cross arm 30 packing piece and clamps for above with bolt & nut 31 33 kv f bracket with bolts & nuts 32 33 kv pin insulators 33 33 kv pin with nuts 34 armour rod with ferrule dog 35 number plates with clamp for pcc pole 36 alluminium biding wire 37 earth wire clamp with bolt & nuts 38 e bracket for 33 kv 39 p.g. clamp for dog 40 stay set 20x1800 mm 41 top channel 125x65 mm, 3200 mm with clamp 42 m.s. angle 65x65x6 mm, x bracing with 4 clamp 43 p.p. clamp 44 terminal gantry 45 main bus bar complete with structire 46 33 kv pin insulators 47 33 kv pin with nuts 48 33 kv line isolator 49 33 kv bus isolator 50 structure for line & bus isolator 51 33 kv post insulator 52 structure for post insulators 53 33 kv lightening arrestor 54 structure for lightening arrestor 55 90 lbs rail picec for transformer ( 44.64 kg / m ) 56 lt bus chamber with 2 no. incomming lt vcb / acb, 02 no outgoing lt vcb / abc, 01 no bus cupler and lt cable from t / f to lt bus chamber with 33 kv t / f and its fixing arrangement. as per market rate 57 control cable 4x2.5 mm sq. 58 earthing of substation outdoor indoor 59 barbed wire fencing with gate ( switchyard ) 60 33 kv pt 33 kv / 110 vip 61 structure for pt 62 33 kv vcb with double t / f control panel ct 200 / 100 / 1a with ct structure 63 cable aluminium 1x1000 sqmm xlpe 64 alluminium lugs 1000 sqmm 65 33 kv ct / pt pole mounted combined unit ( ct ration 50 / 1 amp & pt ration 33 kv / 110 v ) 66 meter box for installation 33 kv / 110 volt tvm 33 kv 67 9 ph 4 w tvm 33 kv 68 33 kv pilfer proof metering cublicle with ct ration 50 / 1 amp & pt ration 33 kv / 110 volt 69 acsr dog conductor 70 grouting of pole...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32746778 tender for electrification work 1 supply & erection 2 13 m long stp ( galvanized ) 3 11 m long stp ( galvanized ) 4 pcc pole 8.5 m long 5 stone pad 300x300x75 mm 6 x arm m.s. angle 65x65x6 mm, v type 11 kv 7 clamp for channel & x arms holding clamp with bolts & nuts 8 11 kv pollymer pin insulator 9 f bracket with bolts & nuts 10 phase wire 30 sqmm acsr weasel 11 alluminium winding wire 6 swg 12 alluminium jointing sleeves for acsr weasel 13 danger board with clamp for 11 kv 14 painting number mark with paint 15 barbed wire 16 red oxide 17 alluminum paint 18 stay rod 16x1800 mm 19 stay wire gi ( 7 / 3.15 mm ) 7 / 10 swg 20 11 kv stay insulator 21 11 kv stay clamp for stp pole 22 earthing of poles ms earthing rod of 20x2500 mm and 6 swg earthing wire etc 23 t off channel 24 clamps with bolt & nut for channel 25 11 kv disc insulator 26 11 kv disc fitting 27 e bracket 28 ms angle 65x65x6 mm, 2700 mm long bracing with clamp 29 top channel 100x50x2240 mm ( 10.70 kg / m ) 30 11 kv disc insulator 45 kn 31 e bricket 32 pg clamps 33 bolts, nuts & washers 34 gaurding angle 50x50x5x2250 mm 35 clamp for gaurding angle stp pole 36 eye bolt 12x100 mm2 37 g.i. wire no 6 swg 38 g.i. wire no 8 wg 39 3x120 mm2 11 kv xlpe cable 40 i / d & o / d cable jointing kit suitable for 11 kv 3x120 mm2 xlpe cable 41 11 kv ct / pt pole mounted combined unit ( ct ration 20 / 5 amp & pt ration 11 kv / 110 v ) 42 meter box for installation 11 kv / 110 volt tvm 11 kv 43 3 phase 4 w static tvm 11 kv 44 11 kv pilfer proof metering cubicle with ct ration 20 / 5 amp & pt ration 11 kv / 110 volt 45 m.s. channel dropper 100x50x2028 mm 46 11 kv tpmo 47 11 kv fuse set 48 lt pvc cable al. 3.5x400 sqmm 49 lt pvc cable al 1x240 sqmm 50 al. leg long barrel off size ( ls ) 51 4 core lt mcb with box ( ls ) 52 m.s. angle 75x75x6x2028 mm 53 cost of g.i. pipe 32 mm dia 54 cost of copper wire 6 swg 55 copper bond 56 make hold of size 18 mm dia in gi pipe 57 33 kv x arms holding clamp with bolts & nuts 58 33 kv f bracket with bolts & nuts 59 11 kv switchgear i / c 600 / 300 / 5a 350 mva 60 11 kv switchgear o / c 200 / 100 / 5a 350 mva 61 11 kv 3 core cable 185 mmsq xlpe 62 11 kv 3 core cable 120 mmsq xlpe 63 11 kv cable jointing kit 185 sqmm ( indoor & outdoor ) 64 11 kv cable jointing kit 120 sqmm ( indoor & outdoor ) 65 24 volt battery and battery charger with cabinet 66 control cable 4x2.5 mmsq 67 control cable 2x2.5 mmsq 68 grouting of pole...

Ministry Of Labour And Employment - Uttar Pradesh

32687198 bids are invited for enamel paint , aluminium paint , exterior paint , wall putty , turpentine oil , obd , brush , emiry paper , stainer , iron primer , marking tape , lakha dana , spirit , thinner , white dhoti , touchwood , paint remover , turkey umber yellowcolor , raw sienna red color , clear , lacquer , cementobd , snowcem cement paint white , snowcem cementpaint red , veneer plywood , plywood , laminate , fevicolmse total quantity : 246...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32665997 1 supply and commissioning ofthe whole following work including carriage, commissioning with all required material. . 2 8.5 mtr long pcc pole 3 11 meter long stp ( sp 55 ) 4 13 meter long stp ( sp 72 ) 5 stone pad 300x300x75mm 6 v type cross arm for 11kv 7 x arm holding clamp with nut & bolt 8 f bracket for top insulator with nut & bolt 9 ms t off channel 10 11 kv disc insulator ( b&s ) type 11 disc fittingfor weasel / rebbit ( b&s ) type 45 kn 12 11 kv pin insulator with pin 13 stay set complete for 11 kv 14 earthing complete ( ms earthing rod ) 15 acsr dog conductor 16 acsr weasel conductor 17 aluminium binding wire 18 guardingx arm ( ms angle ) 19 gi wire 6 swg for guarding 20 gi wire 8 swg for guarding 21 eye bolts for guard wire with nut 22 ms top channel 125x65 2240 mm 23 dropper channel 100x50x2028mm 24 ms braciing angle long 25 clamp with nut bolt top channel 26 pg clamp 27 clamp with nut bolt guaring channel 28 alluminium paint 29 red oxide 30 e bracketfor fitting top insulator 31 abc cable ( 3x120+1x95+1x16 ) sqmm with sag 32 abc cable ( 3x95+1x70+1x16 ) sqmm with sag 33 11 kv 3x70sqmm jointing kiti / d and o / d 34 11 kv 3x120sqmm jointing kiti / d and o / d 35 fixing of barbed wire 36 fixing of number plate 37 fixing of denger board 38 11 kv xlpe 3x70cable as per respo maual and including costof labour. 39 11 kv xlpe3x120 cable as per respo maual and including costof labour. 40 100 kva t / f with accessories 41 25 kva t / f 42 gi pipe 150mm ( 6 ) thickness 4.80mm as per gtp approved by se mm dvvnl agra. 43 errection and commissioning ofall required material forinstalation of meteringsystem on pcc pole / meter including the work requiredfor energising the line including carriage of material from store centre hansari to work site.11 kv pilfer metering cubical meter, 11 kv ct / pt, meter cubical andtvmprovided by the department. 44 fixing & installation, errection and commissioning ofthe following 11 / 0.4 kv s / s with material including the work requiredfor energising the line and work includes carriage to work site with earthing, grouting, laying, sagging, strenthing, binding of conductor.11kv vcb incoming & outgoing ctr provided by the department. 45 holding clamp with nut & bolt 46 11kv vcb incoming & outgoing ctr 47 100 kva t / f with accessories 48 25 kva t / f 49 11 kv tpmo 50 11 kv fuse set 51 alluminium lugs 52 copper l piece 50*225*10mm 53 4 core lt mcb box 54 l.t. pvc cable 3.5*400sqmm 55 camical earthing 56 lt distribution box with clamp 57 base angle for ct / pt 58 holding clamp with nut & bolt for pcc pole 59 holding clamp with nut & bolt for stp pole 60 stay insulator 61 earth clamp 62 laying 11 kv xlpe 3*70 cable 63 laying 11 kv xlpe 3*120 cable 64 laying and fixing of gi pipe 150mm ( 6 ) thickness 4.80mm as per gtp approved by se mm dvvnl agra. 65 concreating of support...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32665354 supply and commissioning of the whole following work including carriage, commissioning with all required material. 2 8.5 mtr long pcc pole 3 11 meter long stp ( sp 55 ) 4 13 meter long stp ( sp 72 ) 5 stone pad 300x300x75mm 6 v type cross arm for 11kv 7 x arm holding clamp with nut & bolt 8 f bracket for top insulator with nut & bolt 9 ms t off channel 10 11 kv disc insulator ( b&s ) type 11 disc fittingfor weasel / rebbit ( b&s ) type 45 kn 12 11 kv pin insulator with pin 13 stay set complete for 11 kv 14 earthing complete ( ms earthing rod ) 15 acsr dog conductor 16 acsr weasel conductor 17 aluminium binding wire 18 guardingx arm ( ms angle ) 19 gi wire 6 swg for guarding 20 gi wire 8 swg for guarding 21 eye bolts for guard wire with nut 22 ms top channel 125x65 2240 mm 23 dropper channel 100x50x2028mm 24 ms braciing angle long 25 clamp with nut bolt top channel 26 pg clamp 27 clamp with nut bolt guaring channel 28 alluminium paint 29 red oxide 30 e bracketfor fitting top insulator 31 abc cable ( 3x120+1x95+1x16 ) sqmm with sag 32 abc cable ( 3x95+1x70+1x16 ) sqmm with sag 33 11 kv 3x70sqmm jointing kiti / d and o / d 34 11 kv 3x120sqmm jointing kiti / d and o / d 35 fixing of barbed wire 36 fixing of number plate 37 fixing of denger board 38 11 kv xlpe 3x70cable as per respo maual and including costof labour. 39 11 kv xlpe3x120 cable as per respo maual and including costof labour. 40 100 kva t / f with accessories 41 25 kva t / f 42 gi pipe 150mm ( 6 ) thickness 4.80mm as per gtp approved by se mm dvvnl agra. 43 errection and commissioning ofall required material forinstalation of meteringsystem on pcc pole / meter including the work requiredfor energising the line including carriage of material from store centre hansari to work site.11 kv pilfer metering cubical meter, 11 kv ct / pt, meter cubical andtvmprovided by the department. 44 fixing & installation, errection and commissioning ofthe following 11 / 0.4 kv s / s with material including the work requiredfor energising the line and work includes carriage to work site with earthing, grouting, laying, sagging, strenthing, binding of conductor. 45 holding clamp with nut & bolt 46 100 kva t / f with accessories 47 25 kva t / f 48 11 kv tpmo 49 11 kv fuse set 50 alluminium lugs 51 copper l piece 50*225*10mm 52 4 core lt mcb box 53 l.t. pvc cable 3.5*400sqmm 54 camical earthing 55 lt distribution box with clamp 56 base angle for ct / pt 57 holding clamp with nut & bolt for pcc pole 58 holding clamp with nut & bolt for stp pole 59 stay insulator 60 earth clamp 61 laying 11 kv xlpe 3*70 cable 62 laying 11 kv xlpe 3*120 cable 63 laying and fixing of gi pipe 150mm ( 6 ) thickness 4.80mm as per gtp approved by se mm dvvnl agra. 64 concreating of support...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32586636 tender for energizing electrical work 2 13 m long stp ( galvanized ) 3 11 m long stp ( galvanized ) 4 pcc pole 8.5 m long 5 stone pad 300x300x75 mm 6 x arm m.s. angle 65x65x6 mm, v type 11 kv 7 clamp for channel & x arms holding clamp with bolts & nuts 8 11 kv pollymer pin insulator 9 f bracket with bolts & nuts 10 phase wire 30 sqmm acsr weasel 11 alluminium winding wire 6 swg 12 alluminium jointing sleeves for acsr weasel 13 danger board with clamp for 11 kv 14 painting number mark with paint 15 barbed wire 16 red oxide 17 alluminum paint 18 stay rod 16x1800 mm 19 stay wire gi ( 7 / 3.15 mm ) 7 / 10 swg 20 11 kv stay insulator 21 11 kv stay clamp for stp pole 22 earthing of poles ms earthing rod of 20x2500 mm and 6 swg earthing wire etc 23 t off channel 24 clamps with bolt & nut for channel 25 11 kv disc insulator 26 11 kv disc fitting 27 e bracket 28 ms angle 65x65x6 mm, 2700 mm long bracing with clamp 29 top channel 100x50x2240 mm ( 10.70 kg / m ) 30 11 kv disc insulator 45 kn 31 e bricket 32 pg clamps 33 bolts, nuts & washers 34 gaurding angle 50x50x5x2250 mm 35 clamp for gaurding angle stp pole 36 eye bolt 12x100 mm2 37 g.i. wire no 6 swg 38 g.i. wire no 8 wg 39 3x120 mm2 11 kv xlpe cable 40 i / d & o / d cable jointing kit suitable for 11 kv 3x120 mm2 xlpe cable 41 11 kv ct / pt pole mounted combined unit ( ct ration 20 / 5 amp & pt ration 11 kv / 110 v ) 42 meter box for installation 11 kv / 110 volt tvm 11 kv 43 3 phase 4 w static tvm 11 kv 44 11 kv pilfer proof metering cubicle with ct ration 20 / 5 amp & pt ration 11 kv / 110 volt 45 m.s. channel dropper 100x50x2028 mm 46 11 kv tpmo 47 11 kv fuse set 48 lt pvc cable al. 3.5x400 sqmm 49 lt pvc cable al 1x240 sqmm 50 al. leg long barrel off size ( ls ) 51 4 core lt mcb with box ( ls ) 52 m.s. angle 75x75x6x2028 mm 53 cost of g.i. pipe 32 mm dia 54 cost of copper wire 6 swg 55 copper bond 56 make hold of size 18 mm dia in gi pipe 57 33 kv x arms holding clamp with bolts & nuts 58 33 kv f bracket with bolts & nuts 59 11 kv switchgear i / c 600 / 300 / 5a 350 mva 60 11 kv switchgear o / c 200 / 100 / 5a 350 mva 61 11 kv 3 core cable 185 mmsq xlpe 62 11 kv 3 core cable 120 mmsq xlpe 63 11 kv cable jointing kit 185 sqmm ( indoor & outdoor ) 64 11 kv cable jointing kit 120 sqmm ( indoor & outdoor ) 65 24 volt battery and battery charger with cabinet 66 control cable 4x2.5 mmsq 67 control cable 2x2.5 mmsq 68 grouting of pole 69 33 kv gaurding angle 65x65x6x3500 mm 70 33 kv v type cross arm 71 33 kv pin insulator 72 33 kv pin with nut...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32586256 tender for energizing electrical work 2 13 m long stp ( galvanized ) 3 pcc pole 9.0 m 4 stone pad 300x300x75 mm 5 danger board with clmp for 11 kv 6 barbed wire 7 red oxide 8 alluminium paint 9 earthing of pole ms earthing rod of 20x2500 mm and 6 swg earthing wire 10 ms angle 65x65x6 mm, 2700 mm long bracing with clamp 11 11 kv disc insulator 45 kn 12 disc fitting for dog 13 bolts, nuts & washer 14 33 kv gaurding angle 65x65x6x3500 mm 15 clamp for gaurding angle stp pole 16 eye bolt 12x100 mm2 17 g.i. wire no. 6 swg 18 g.i. wire no. 8 swg 19 xlpe cable 3x300 sqmm for 33 kv line ( 3.25 km double ckt ) 20 staright through jointing kit for xlpe cable 3x300 sqmm 21 outdoor joint kit for xlpe cable 3x300 sqmm 22 gi pipr 6 dia 23 hdpe pipe 140 mm 24 ms channel dropper 125x65 mm, 3200 25 cost of gi pipe 32 mm dia 26 cost of copper wire 6 swg 27 copper bond 28 make hold of size 18 mm dia in gi pipe 29 33 kv v type cross arm 30 packing piece and clamps for above with bolt & nut 31 33 kv f bracket with bolts & nuts 32 33 kv pin insulators 33 33 kv pin with nuts 34 armour rod with ferrule dog 35 number plates with clamp for pcc pole 36 alluminium biding wire 37 earth wire clamp with bolt & nuts 38 e bracket for 33 kv 39 p.g. clamp for dog 40 stay set 20x1800 mm 41 top channel 125x65 mm, 3200 mm with clamp 42 m.s. angle 65x65x6 mm, x bracing with 4 clamp 43 p.p. clamp 44 terminal gantry 45 main bus bar complete with structire 46 33 kv pin insulators 47 33 kv pin with nuts 48 33 kv line isolator 49 33 kv bus isolator 50 structure for line & bus isolator 51 33 kv post insulator 52 structure for post insulators 53 33 kv lightening arrestor 54 structure for lightening arrestor 55 90 lbs rail picec for transformer ( 44.64 kg / m ) 56 lt bus chamber with 2 no. incomming lt vcb / acb, 02 no outgoing lt vcb / abc, 01 no bus cupler and lt cable from t / f to lt bus chamber with 33 kv t / f and its fixing arrangement. as per market rate 57 control cable 4x2.5 mm sq. 58 earthing of substation outdoor indoor 59 barbed wire fencing with gate ( switchyard ) 60 33 kv pt 33 kv / 110 vip 61 structure for pt 62 33 kv vcb with double t / f control panel ct 200 / 100 / 1a with ct structure 63 cable aluminium 1x1000 sqmm xlpe 64 alluminium lugs 1000 sqmm 65 33 kv ct / pt pole mounted combined unit ( ct ration 50 / 1 amp & pt ration 33 kv / 110 v ) 66 meter box for installation 33 kv / 110 volt tvm 33 kv 67 9 ph 4 w tvm 33 kv 68 33 kv pilfer proof metering cublicle with ct ration 50 / 1 amp & pt ration 33 kv / 110 volt 69 acsr dog conductor 70 grouting of pole...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32585111 tender for energizing electrical work 2 11 m long stp ( galvanized ) 3 pcc pole 8.5 m long 4 stone pad 300x300x75 mm 5 x arms m.s. angle 65x65x6 mm, v type 11 kv 6 clamp for channel & x arms holding clamp with bolts & nuts 7 11 kv pollymer pin insulator 8 f bracket with bolts & nut 9 phase wire 30 sqmm acsr weasel 10 alluminium winding wire 6 swg 11 alluminium jointing sleaves for acsr weasel 12 danger board with clamp for 11 kv 13 painting number mark with paint 14 barbed wire 15 red oxide 16 alluminium paint 17 stay rod 16x1800 mm 18 stay wire gi ( 7 / 3.15 mm ) 7 / 10 swg 19 11 kv stay insulator 20 11 kv stay clamp for stp pole 21 earthing of pole ms earthing rod of 20x2500 mm and 6 swg earthing wire 22 t off channel 23 clamps with bolt & nut for channel 24 11 kv disc insulator 25 11 kv disc fitting 26 e bracket 27 m.s. angle 65x65x6 mm, 2700 mm long bracing with clamp 28 top channel 100x50x2240 mm ( 10.70 kg / m ) 29 11 kv disc insulator 45 kn 30 e bracket 31 pg clamps 32 bolts, nuts & washers 33 gaurding angle 50x50x5x2500 mm 34 clamp for gaurding angle stp pole 35 eye bolt 12x100 mm2 36 gi wire no 6 swg 37 gi wire no 8 swg 38 3x120 mm2 11 kv xlpe cable 39 i / d & o / d cable jointing kit suitable for 11 kv 3x120 mm2 xlpe cable 40 11 kv ct / pt pole mounted combined unit ( ct ration 20 / 5 amp & pt ration 11 kv / 110 v ) 41 meter box for installation 11 kv / 110 volt tvm 11 kv 42 3 phase 4 w static tvm 11 kv 43 11 kv pilfer proof metering cubicle with ct ration 20 / 5 amp & pt ration 11 kv / 110 volt 44 m.s. channel dropper 100x50x2028 mm 45 11 kv tpmo 46 11 kv fuse set 47 lt pvc cable al. 3.5x400 sqmm 48 lt pvc cable al. 1x240 sqmm 49 al. leg long barrel off size ( ls ) 50 4 core lt mcb with box ( ls ) 51 m.s. angle 75x75x6x2028 mm 52 cost of g.i. pipe 32 mm dia 53 cost of copper wire 6 swg 54 copper bond 55 make hold of size 18 mm dia in gi pipe 56 grouting of pole...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

32584902 tender for energizing electrical work 2 13 m long stp ( galvanized ) 3 11 m long stp ( galvanized ) 4 pcc pole 8.5 m long 5 stone pad 300x300x75 mm 6 x arm m.s. angle 65x65x6 mm, v type 11 kv 7 clamp for channel & x arms holding clamp with bolts & nuts 8 11 kv pollymer pin insulator 9 f bracket with bolts & nuts 10 phase wire 30 sqmm acsr weasel 11 alluminium winding wire 6 swg 12 alluminium jointing sleeves for acsr weasel 13 danger board with clamp for 11 kv 14 painting number mark with paint 15 barbed wire 16 red oxide 17 alluminum paint 18 stay rod 16x1800 mm 19 stay wire gi ( 7 / 3.15 mm ) 7 / 10 swg 20 11 kv stay insulator 21 11 kv stay clamp for stp pole 22 earthing of poles ms earthing rod of 20x2500 mm and 6 swg earthing wire etc 23 t off channel 24 clamps with bolt & nut for channel 25 11 kv disc insulator 26 11 kv disc fitting 27 e bracket 28 ms angle 65x65x6 mm, 2700 mm long bracing with clamp 29 top channel 100x50x2240 mm ( 10.70 kg / m ) 30 11 kv disc insulator 45 kn 31 e bricket 32 pg clamps 33 bolts, nuts & washers 34 gaurding angle 50x50x5x2250 mm 35 clamp for gaurding angle stp pole 36 eye bolt 12x100 mm2 37 g.i. wire no 6 swg 38 g.i. wire no 8 wg 39 3x120 mm2 11 kv xlpe cable 40 i / d & o / d cable jointing kit suitable for 11 kv 3x120 mm2 xlpe cable 41 11 kv ct / pt pole mounted combined unit ( ct ration 20 / 5 amp & pt ration 11 kv / 110 v ) 42 meter box for installation 11 kv / 110 volt tvm 11 kv 43 3 phase 4 w static tvm 11 kv 44 11 kv pilfer proof metering cubicle with ct ration 20 / 5 amp & pt ration 11 kv / 110 volt 45 m.s. channel dropper 100x50x2028 mm 46 11 kv tpmo 47 11 kv fuse set 48 lt pvc cable al. 3.5x400 sqmm 49 lt pvc cable al 1x240 sqmm 50 al. leg long barrel off size ( ls ) 51 4 core lt mcb with box ( ls ) 52 m.s. angle 75x75x6x2028 mm 53 cost of g.i. pipe 32 mm dia 54 cost of copper wire 6 swg 55 copper bond 56 make hold of size 18 mm dia in gi pipe 57 33 kv x arms holding clamp with bolts & nuts 58 33 kv f bracket with bolts & nuts 59 11 kv switchgear i / c 600 / 300 / 5a 350 mva 60 11 kv switchgear o / c 200 / 100 / 5a 350 mva 61 11 kv 3 core cable 185 mmsq xlpe 62 11 kv 3 core cable 120 mmsq xlpe 63 11 kv cable jointing kit 185 sqmm ( indoor & outdoor ) 64 11 kv cable jointing kit 120 sqmm ( indoor & outdoor ) 65 24 volt battery and battery charger with cabinet 66 control cable 4x2.5 mmsq 67 control cable 2x2.5 mmsq 68 grouting of pole...