Uttar Pradesh Jal Nigam - Uttar Pradesh

34223719 repair and renovation work for rashtriya raksha university, transit campus at dr. smnru university, lucknow repair and renovation work for rashtriya raksha university, transit campus at dr. smnru university, lucknow , dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead , demolishing r.c.c. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge , demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge.in cement mortar , demolishing rb work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge.in cement mortar , dismantling doors, windows and clerestory windows ( steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :of area beyond 3 sq. metres , dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. for thickness of tiles 10 mm to 25 mm , earth work in excavation by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by engineer incharge. , 1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources ) , providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth beam : , same as item no 5 above , 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources ) ( foundation ) , same as item no 5 above , 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources ) ( column ) , reinforced cement concrete work in walls ( any thickness ) , including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources ) , steel reinforcement for r.c.c. work including traightening, cutting, bending, placing in position and binding all complete upto plinth level. mild steel and medium tensile steel bars , brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in foundation below plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 ( 1 cement : 6 coarse sand ) , brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 ( 1 cement : 6 coarse sand ) , half brick masonry with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor v level. cement mortar 1:4 ( 1 cement :4 coarse sand ) , supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. , diluting and injecting chemical emulsion for post constructional anti termite treatment ( excluding the cost of chemical emulsion ) : treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 ( 1 cement : 2 coarse sand ) to match the existing floor:with chlorpyriphos / lindane e.c. 20% with 1% concentration , kota stone slab flooring over 20 mm ( average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand ) : 25 mm thick , kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm ( average ) thick cement mortar 1:3 ( 1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. , steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. hot finished seamless type tubes , providing corrugated g.s. sheet roofing including vertical / curved surface fixed with polymer coated j or l hooks, bolts and nuts 8 mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces ) , excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.80 mm thick with zinc coating not less than 275 gm / m² , providing ridges or hips of width 60 cm overall width plain g.s. sheet fixed with polymer coated j or l hooks, bolts and nuts 8 mm dia g.i. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gm / m² , providing and fixing 15 cm wide, 45 cm overall semi circular plain g.s. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 0.80 mm thick with zinc coating not less than 275 gm / m² , providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including isi marked stainless steel butt hinges with necessary screws , m.s.work in d / w hold fast , m.s.work in d / w m.s.grill , z section windows , providing and fixing angle iron frames for doors of mild steel angle sections , 15 mm cement plaster of mix : 1:6 ( 1 cement: 6 coarse sand ) , 12 mm cement plaster of mix : 1:6 ( 1 cement: 6 coarse sand ) , 12 mm cement plaster of mix : 1:6 ( 1 cement: 6 coarse sand ) , providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. , distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : new work ( two or more coats ) over and including water thinnable priming coat with cement primer , finishing walls with acrylic smooth exterior paint with silicone additives of required shade new work ( two or more coats applied @ 1.43 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm ) , ( d ) finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 ( 1 cement :4 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. ( e ) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“all above operations to be done in order and as directed and specified by the engineer in charge : 22.7.1 with average thickness of 120 mm and minimum thickness at khurra as 65 mm. , with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron / steel works , painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work , with ready mixed pink or grey primer of approved brand and manufacture on wood work ( hard and soft wood ) , painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work , providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes , providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm , providing and laying vitrified tiles in different sizes ( thickness to be specified by manufacturer ) , with water absorption less than 0.08 % and conforming to i.s. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 ( 1 cement: 3 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joint with white cement & matching pigments etc. complete. size of tile 600x600 mm , providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more ( thickness to be specified by the manufacturer ) , of 1st quality conforming to is : 15622, of approved make, in all colours, shades, except white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including pointing the joints with white cement and matching pigments etc., complete. , design supply & installation of suspended spider glazing system designed to withstand the wind pressure as per is 875 ( part iii ) . the suspended system held with spider fittings of ss 316 grade steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with ss 316 grade stainless steel spider & bolt assembly with laminated glass fins 21 mm thick. the glass fins and glass panel assembly shall be connected to slab / beams by means of ss 316 grade stainless steel brackets & anchor bolts and at the bottom using ss channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, teflon / nylon bushes and separators to prevent bi metallic contacts, all complete to perform as per specification and approved drawings. the complete system to be designed to accommodate thermal expansion & seismic movements etc. the joints between glass panels ( 6 to 8 mm ) and gaps at the perimeter & in u channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. the rate shall include all design, engineering and shop drawing including approval from structural designer, labour, t&p, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, buffer plates, fastener, anchors, ss channel laminated glass etc. all complete. for the purpose of payment, actual elevation area of glazing including thickness of joints and the portion of glass panel inside the ss channel shall be measured. , steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. , p / f curtain rods of 1.25mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with c.p. brass screws and wooden plugs etc. wherever necessary complete ( a ) 25 mm dia. , providing & fixing fly proof wire gauze to windows, clerestory windows & doors with m.s. flat 15x3 mm and nuts & boltscomplete.stainless steel ( grade 304 ) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides. , providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of size 595x595 mm of approved texture, design and patterns having nrc ( noise reduction coefficient ) of 0.50 ( minimum ) as per is 8225:1987, light reflectance of 85% ( minimum ) . non combustible as per bs:476 ( part 4 ) , fire performance as per bs:476 ( part 6 &7 ) , humidity resistance of 100%, thermal conductivity < 0.043 w / m k as per astm 518:1991, in true horizontal level suspended on interlocking metal powder coated t grid of hot dipped galvanised iron section of 0.40 mm thick on silhouette profile, rotary stiched double webbed white with 6mm reveal profile ( white / black ) , comprising of main t runners of size 15x42mm of length 3000 mm, cross t of size 15x42 mm of length 1200 mm and secondary intermediate cross t of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items ( galvanizing @ 80 grams per sqm ) i.e. 50 mm long, 8 mm outer diameter m 6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and l shape level adjuster of size 85x25x2 mm. galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall s.s screws. the work shall be carried out as per specifications, drawing and as per directions of the engineer in charge. with 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles , applying priming coat: with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron / steel works , painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is:13592 type a, including jointingwithsealringconformingtois: 5382, leaving 10 mm gap for thermal expansion. single push fit coupler110 mm dia , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is:13592 type a, including jointingwithsealringconformingtois: 5382, leaving 10 mm gap for thermal expansion.shoe ( plain ) 110 mm shoe , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is:13592 type a, including jointingwithsealringconformingtois: 5382, leaving 10 mm gap for thermal expansion. plain bend 87.5 deg 110 mm dia , providing and fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with m.s. screws of required length, including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand ) and making good the wall etc. complete. 110 mm , fixing of door chaukhats , providing & fixing stainless steel sliding door bolts isi marked anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade with nuts and screws etc complete. ( a ) 250mm x 16mm . , providing and fixing stainless steel towerbolts ( barrel type ) with necessary screws etc. complete ( a ) 300 mm x 10mm , providing and fixing stainless steel handles with screws etc. complete ( a ) 125 mm , providing & supplying curtains. , cc flooring with 1:2:4 with 40 mm thick , cement plaster up 30 cm heght with 1:3 cement sand morter , providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, ( i ) single socketed pipes. 110 mm diameter , wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm frls pvc insulated copper conductor single core cable in surface / recessed medium class pvc conduit, with piano type switch, phenolic laminated sheet, suitable size m.s. box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc. as required. , wiring for light / power plug with 2x4 sq. mm frls pvc insulated copper conductor single core cable in surface / recessed steel conduit alongwith 1 no. 4 sq. mm frls pvc insulated copper conductor single core cable for loop earthing as required. , wiring for circuit / submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface / recessed medium class pvc conduit as required. 4 x 10 sq. mm + 2 x 6 sq. mm earth wire , wiring for circuit / submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface / recessed medium class pvc conduit as required.2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire , wiring for circuit / submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface / recessed medium class pvc conduit as required. 4 x 16 sq. mm + 2 x 6 sq. mm earth wire , supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15 / 16 a socket outlet 3 pin 5 / 6 a socket outlet , supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15 / 16 a socket outlet 15 / 16 a socket outlet , installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length ( upto 30 cm ) with 1.5 sq. mm frls pvc insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. , installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. upto 450 mm sweep , providing and fixing circular / hexagonal g.i. box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick g.i. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the g.i. box by means of 3.3 mm dia round headed screws, one lock at the corners. clamp shall be made of 12 mm dia m.s. bar bent to shape as per standard drawing. ( dsr civil 2014 item no. 10.18 ) , supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. , supply and fixing of1x22 watt led tube light ( surface ) complete in all respect. , supply and fixing of36 46 watt recess mounting led square light complete in all respect. , supply and fixing of15w 18w led down lighter complete in all respect. , supply and fixing of 17 watt led mirror light and complete in all respect. , supply and fixing of10w 15w led cealing light complete in all respect. , supply and fixing ofwall mounted light fixture complete in all respect. , supply and erection of ac 230 / 250 volts, 50 hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required.300mm sweep. , supply and erection of ac 1200mm sweep, 230 / 250 volts, 50 hz ceilling fan with down rod, blades including connection etc. complete as required , supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 6 way ( 4 + 18 ) , double door , supplying and fixing 5 a to 32 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , supplying and fixing following rating, double pole, ( single phase and neutral ) , 240 v, residual current circuit breaker ( rccb ) , having a sensitivity current 30 ma in the existing mcb db complete with connections, testing and commissioning etc. as required. 40 a , supplying and fixing following rating, double pole, ( single phase and neutral ) , 240 v, residual current circuit breaker ( rccb ) , having a sensitivity current 30 ma in the existing mcb db complete with connections, testing and commissioning etc. as required. 63 a , s&f of 100 a, 16 ka, tpmccb mccbthermal magnetic release , s&f of 125 a, 16 ka, tpmccb mccbthermal magnetic release , earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. ( but without charcoal / coke and salt ) as required. , supplying and laying 25 mm x 5 mm g.i strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with g.i. nut, bolt, spring, washer etc. as required. , providing and laying earth connection from earth electrode with 6 swg dia g.i. wire in 15 mm dia g.i. pipe from earth electrode including connection with g.i. thimble excavation and re filling as required. , supplying and fixingfollowing size / modules, gi box along with modular base& cover plate for modular switches in recess etc as required. 1 or 2 module ( 75mm x 75 mm ) , supplying and fixing following modular switch / socket on theexisting modular plate & switch box including connections but excluding modular plate etc as required. telephone socket outlet , supplying and drawing telephone wire following pair 0.5 sqmm fr pvc insulated annealed copper conductor, unarmoured telephone cable in the existing surface / recessed steel / pvc conduit as required. 2 pair , supply and fixing of36 watt led hanging light complete in all respect. , supply and erection of ac 1400mm sweep, 230 / 250 volts, 50 hz ceilling fan with down rod, blades including connection etc. complete as required , supplying and fixing extra conduit down rod of 60 cm length g.i. pipe 15 mm dia, heavy gauge including painting etc. as required. , numbering of ceiling fan / exhaust fan / fluorescent fittings as required. , providing and fixing water closet squatting pan ( indian type w.c. pan ) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests , providing and fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) , conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : w.c. pan with isi marked white solid plastic seat and lid , providing & fixing toilet paper holder c.p. brass , providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer in charge. , providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: white vitreous china wash basin size 630x450 mm with a single 15 mm c.p. brass pillar tap , providing and fixing cp brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge. , providing and fixing ptmt towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. , providing and fixing ptmt soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. , providing and fixing c.p.brass angle valve for basin mixer and geyser points of approved quality conforming to is 8931 ( including angle valve for wc flushing cistern, jet & kitchen sink ) 15 mm nominal bore , providing and fixing uplasticised pvc connection pipe with brass unions :45 cm length 15 mm nominal bore , providing and fixing stainless steel aisi 304 ( 18 / 8 ) kitchen sink as per is: 13983 with c.i. brackets and stainless steel plug 40 mm, including painting offittings and brackets, cuttingandmakinggoodthe walls wherever requiredkitchen sink with drain board 510x1040 mm bowl depth 200 mm , providing & fixing pvc waste pipe for sink including pvc waste fittings complete flexible pipe 32mm dia , providing and fixing 600x450 mm beveled edge mirror of superior glass ( of approved quality ) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. , providing and fixing c.p. brass bib cock of approved quality conforming to is:8931 : 15mm nominal bore , providing and fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms. 15mm nominal bore , providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption ) , having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of engineer in charge. , providing and fixing ptmt bottle trap for urinal. bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms , providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size ) as perdirection of engineer in charge and finished smooth.granite stone of approved shade , providing and fixing chlorinated polyvinyl chloride ( cpvc ) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i / c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia pipes , providing and fixing chlorinated polyvinyl chloride ( cpvc ) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i / c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia pipes , providing and fixing chlorinated polyvinyl chloride ( cpvc ) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i / c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.concealed work, including cutting chases and making good the walls etc. 32 mm nominal outer dia pipes , providing and fixing brass stop cock of approved quality : 15 mm nominal bore , providing and fixing brass stop cock of approved quality : 20 mm nominal bore , providing and fixing gun metal gate valve with c.i. wheel of approved quality ( screwed end ) :for vertical pipe connection with terrace ringmain 25mm nominal bore , providing and fixing gun metal gate valve with c.i. wheel of approved quality ( screwed end ) :for vertical pipe connection with terrace ringmain 32mm nominal bore , providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is :13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, ( i ) single socketed pipes.110 mm dia ( for rain water ) , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is:13592 type a, including jointingwithsealringconformingtois: 5382, leaving 10 mm gap for thermal expansion. single push fit coupler 110 mm dia , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is:13592 type a, including jointingwithsealringconformingtois: 5382, leaving 10 mm gap for thermal expansion. single tee with door 110x110x110 mm , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is:13592 type a, including jointingwithsealringconformingtois: 5382, leaving 10 mm gap for thermal expansion.plain bend 87.5 deg 110 mm dia , providing and fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with m.s. screws of required length, including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand ) and making good the wall etc. complete.110 mm dia , making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size ) over p.v.c. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 ( 1 cement : 3 coarse sand ) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. , providing and placing on terrace ( at all floor levels ) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. , providing, fixing, jointing and testing, upvclow noise swrhaving noise insulation less than 10db at 2lps flow rate pipeto wall, ceiling and floor, approved quality, complete, for soil, waste & rain water drain including pushfit jointing with seal ring. ( i ) single socketed pipes. internal toilet ( soil & waste pipe ) 75 mm , providing, fixing, jointing and testing, upvclow noise swrhaving noise insulation less than 10db at 2lps flow rate pipeto wall, ceiling and floor, approved quality, complete, for soil, waste & rain water drain including pushfit jointing with seal ring. ( i ) single socketed pipes. internal toilet ( soil & waste pipe ) 110 mm , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. bend without door ( 87.5° ) 110mm bend , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. bend without door ( 87.5° ) 75mm bend , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. bend without door ( 45° ) 100mm , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. bend without door ( 45° ) 75mm , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes including jointing with seal ring leaving 10 mm gap for thermal expansion.single tee without door 110mm , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. single tee without door75 mm , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. coupler 110mm , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. clean out plug ( cop 110mm , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. clean out plug ( cop 75 mm , providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. vent cow l110mm , providing, fixing, jointing and testing , oflow noise pvc multi floor trap without jali ofminimum 50 mm water seal, making necessarycuttingin slabor floors and making goodincluding supports with cement concrete 1:3:6complete as approved by engineer in charge.110mm x 75mm x 50mm / 40mm ( toilet ) , providing, fixing, jointing and testing , oflow noise pvc nahanitrap without jali ofminimum 50 mm water seal, making necessarycuttingin slabor floors and making goodincluding supports with cement concrete 1:3:6complete as approved by engineer in charge.110mm x 75mm ( toilet ) , providing and fixing ptmt grating of approved quality and colour.rectangular type with openable circular lid150 mm nominal size square 100 mm diameter of the inner hinged round grating ( including balcony ) , providing and fixing square mouth s.w. gully trap class sp 1 complete with c.i. grating brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size ( inside ) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :150 x 100mm size p typewith common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , supply and fixing of36 watt led hanging light complete in all respect. , supply and erection of ac 1400mm sweep, 230 / 250 volts, 50 hz ceilling fan with down rod, blades including connection etc. complete as required , supplying and fixing extra conduit down rod of 60 cm length g.i. pipe 15 mm dia, heavy gauge including painting etc. as required. , numbering of ceiling fan / exhaust fan / fluorescent fittings as required. , boring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in is: 2800 ( part i ) , including collecting samples from different strata, preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90 metre depth below ground level.300mm dia 300 mm dia , boring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in is: 2800 ( part i ) , including collecting samples from different strata, preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in harge, beyond 90 metre & upto 150 metre depth below round level.300 mm dia , supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer in charge. 150 mm nominal size dia , supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized pvc medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of engineer in charge. 200 mm nominal size dia , supplying, assembling, lowering and fixing in vertical position in bore well unplasticized pvc medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including hire & labour charges, fittings &accessories etc. all complete, for all depths, as per direction of engineer in charge.150 mm nominal size dia , supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of engineer incharge. 3.14* ( .150*.150 .075*.075 ) *150 , development of tube well in accordance with is : 2800 ( part i ) and is:11189, to establish maximum rate of usable water yield without sand content ( beyond permissible limit ) , with required capacity ai compressor, running the compressor for required time till well is fully developed, measuring yield of well by “v” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i / c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of engineer in charge. , providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore wellhousing / casing pipe, removable as per requirement, all complete for borewell of:200 mm dia , providing and fixing m.s. clamp of required dia to the top of casing / housing pipe of tubewell as per is: 2800 ( part i ) , including necessary bolts & nuts of required size complete.200 mm clamp. , providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tubewell as per is:2800 ( part i ) . 200 mm dia. , supply and fixing of tube well pump 10.0 h.p. cable and other necessary all materils.ksb make or equvilent , water supply of tanker 5000 litre capacity of boring , supply and fixing of nylon jali around the slotted pipes complete as required up to 10 mtr. , supply of 80mm dia m.s. column pipe of class c both and socketed with heavy sockets in 3 / 6 meter length and one end flanged complete with interlocking arrangements. , supply of 80mm dia m.s. column pipe clamps with nut bolts packing etc. , excavating trenches in all kinds ofsoil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. up to 1.50 m depth pipes 80 mm to 300 mmdiameter , excavating trenches in all kinds ofsoil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. 1.50 m to 3.00 m depth pipes 80 mm to 300 mmdiameter , opentimbering in trenches including shuttering and shoring complete. ( measurement to be taken of the face area timbered ) depth not exceeding 1.5 meter , opentimbering in trenches including shuttering and shoring complete. ( measurement to be taken of the face area timbered ) depth 1.5 to3.00meter , providing and laying nonpressurenp 2 class ( light duty ) rcc pipe with collars jointed withstiffmixtureofcement mortar in the proportion of 1:2 ( 1cement : 2 finesand ) includingtestingof joints etc. complete.150 mm.dia. rccpipes , providing and laying nonpressurenp 2 class ( light duty ) rcc pipe with collars jointed withstiffmixtureofcement mortar in the proportion of 1:2 ( 1cement : 2 finesand ) includingtestingof joints etc. complete.250 mm.dia. rccpipes , providing and laying cement concrete 1:5:10 ( 1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size ) upto the haunches of pipes including bed concrete as per standard design150 mm.dia. rccpipes , providing and laying cement concrete 1:5:10 ( 1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size ) upto the haunches of pipes including bed concrete as per standard design 250 mm.dia. rccpipes , constructing brick masonry manhole in cement mortar 1:4 ( 1 cement :4 coarse sand ) rcc top slab with 1:2:4 mix ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size ) , foundation concrete 1:4:8 mix ( 1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size ) inside plastering 12mm thick with cement mortar 1:3 ( 1 cement :3 coarse sand ) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size ) finished with a floating coat of neat cement complete as per standard design. , inside size 90x80cms and 45cms deep including ci cover with frame ( light duty ) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg ( weight of cover 23 kg and weight of frame 15kg ) .with common burnt clay fps ( non modular ) bricks of class designation 75 ( i ) for sewer line , extra for depth for manholes:size 90x80cm with with common burnt clay fps ( non modular ) bricks of class designation 7.5 , inside size 90x120cms and 90cms deep including ci cover with frame ( medium duty ) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58kg ) . with common burnt clay fps ( non modular ) bricks of class designation 75 ( i ) for sewer line , extra for depth for manholes: size 90x120cm with with common burnt clay fps ( non modular ) bricks of class designation 7.5 , providing orange colour safety footrests of minimum 6 mm thick plastic encapsulated as per is:10910 on 12 mm dia steel bar , p / laying of interlocking road , p / making storm water drain 300*450 mm , p / f of chain link fencing wall , p / making of gate , site clearing , surface drasing , cost of signage , cost of notice board , cost of biomatric , interactive board, interactive diagonal: 1975 mm, usb powered, infrared, multi touch ( 6 touch ) , supports windows xp, vista, windows 7, windows 8, window 10 and linux + ceramic steel board size: 120 x 180 cm make: romark / globus / brio.with resolution xga 1024x768 , 3200 ansi lumen, hdmi / vga inputs and inclusive of ceiling / wall mount kit, all cables connector and conduits etc. make: benq, globus, ricoh with digital / smart podium: the podium shall be wheel mounted capable of moving in all directions with a facility of lock them while the electronic podium is in use. the enclosure shall be made of polymer powder coated steel body with wooden top panels, designed to work in suitable environmental conditions. the wooden top shall have lock and key and should have a sliding cover for opening / closing easily. the podium should have housing and connectivity for visual presenter while the visualizer is in use and not in use. at the time of using the visualiser , drawer can be opened and visualiser can be used. the construction of the podium should be such that, while the podium is locked and not is use, there should not be any port exposed / visible on the outer body for breakage / mishandling.built in highly sensitive interactive panel with adjustable tilt ( power driven motorized system ) & a mechanism to make the panel stable so that it does not shake while writingwith following minimum features.led 53.0 cm ( 21 inches ) or higher 1920 x 1080 or higherone usb, one vga / dviport 4000 lpi ( lines per inch ) approximately 200 points per second 2048 levels display panel should have inbuilt speakerdigital teaching device, controller, i5 pc with wi fi card inbuilt amplifier, speaker and with basic visualizer, no windows make : globus, brio. wall mount 1 kva ups with casingcomplete installation of the entire unit , workstation table, panel based partition, particle board edge banded top , high back chair, pu chrome arm, gas lift, chrome base, fabric tapestry synchro tilt , executive table, particle board top w1650 x d1900 x h750 , medium back chair, chrome cushion arm, gas lift, chrome base, leatheritte tapestry , visitor chair, chrome cushion arm, chrome plated pipe stand, leatheritte tapestry , executive table, particle board top , high back chair, chrome cushion arm, gas lift, chrome base, leatheritte tapestry , single seater sofa, wooden frame, ss pipe leg, size in mm 830 ( l ) x 780 ( d ) x 755 ( h ) leatherette , three seater sofa, wooden frame, ss pipe leg, size in mm 1825 ( l ) x 780 ( d ) x 755 ( h ) leatherette , centre table, ss pipe frame, chrome finish, toughned black glass, top 12mm thick, lower glass 8mm thick , cafe chair, without arm, ss pipe frame chrome finish, leatherite tapestry , café table, ss pipe frame chrome finish, granite top, size in mm 900 x 900 , dual desk, plpb edge banded top, seat & back, powder coated pipe frame, top size 1050 x 400 x 18mm thick overall size 1050 x 980 x 750 two seater , workstation table, panel based partition, particle board edge banded top ( rs. 69500 / 4= rs.17375 ) , medium back chair, pipe chrome arm, gas lift, chrome base, leatherite tapestry swivel tilt , steel almirah, 2 glass doors, 4 adjustable shelf, thickness 0.8mm , student / traning room chair, pu arm, plpb folding writing pad, book trey under seat, powder coated pipe frame, fabric tapestry, marino 10002 top colour, writing pad size : 535 x 300 x 18 mm thick , single seater sofa, wooden frame, ss pipe leg, size in mm 830 ( l ) x 780 ( d ) x 755 ( h ) leatherette , three seater sofa, wooden frame, ss pipe leg, size in mm 1825 ( l ) x 780 ( d ) x 755 ( h ) leatherette , centre table, ss pipe frame, chrome finish, toughned black glass, top 12mm thick, lower glass 8mm thick , conference table, particle board edge banded top w3600 x d1200 x h750 , high back chair, chrome cushion arm, gas lift, chrome base, leatheritte tapestry , cost of podium , s / i / t / c of split ac 2 ton , s / i / t / c of split ac 1.50ton , s / i / t / c of i7 16 gb ram , 512ssd , 1tb hdd with windows 10 and microsoft preloaded wire opticalmouse and keyboard with spekar and webcam , canon image runner c3226 with dadf and toner , hp colour laser mfp 178nw printer , s / i / t / c of sony tv kd55x75k in5 , supply of 63kva , 415 volts dg set , s / i / t / c of water cooler with r o system , cat6 utp cable ( 300m ) , i / o box dlink , path cable cat6 ( 1m ) , path cable cat6 ( 2m ) , ethernate 24 port gigabite managed l3 switch , 24 port patch panel , network box 6u rack , instalation charges , cat6 utp cable ( 100m ) , ethernate 16 port gigabite managed l3 switch , 16 port patch panel , network box 4u rack , ip camera ( bullet / dome ) , 8 port poe switch , 8 channel nvr , survillance hdd 4tb , cat 6 utp wire ( 100m ) , 4 u rack , 16 port poe switch , 16 channel nvr , cat 6 utp wire ( 300m ) , instalation of cc tv , cost of maono au 100 condenser clip on lavalier microfone with 6 m audio cable , cost of fire ectinguisher...

National Thermal Power Corporation Limited - Uttar Pradesh

34217824 procurement of spare parts for 03 nos screw air compressor for ntpc procurement of spare parts for 03 nos screw air compressor for ntpcsingrauli , kes 37 / 45 / 55:gasket , kes 37 / 45 / 55:service kit mpvl , kes 37 / 45 / 55:intake valve assly , kes 37 / 45 / 55:hose assly , kes 37 / 45 / 55:hose assly , kes 37 / 45 / 55:gasket air oil seperator , kes 37 / 45 / 55:air oil separator element , kes 37 / 45 / 55:hose assly , kes 37 / 45 / 55:oil filter element , kes 37 / 45 / 55:hose assly , kes 37 / 45 / 55:hose assly , kes 37 / 45 / 55:air filter element , kes 37 / 45 / 55:blow down valve assly , hose assy. 1 1 / 2x 750 l:273.02.558.50 , hose assembly:271.01.634.50 , k smart special fluid...

Uttar Pradesh Rajya Vidyut Utpadan Nigam Limited - Uttar Pradesh

34192105 repairing of various spare of diesel locomotive wds 4b, clw, mak 21 of coal handling plant, btps, obra 1 repairing of self starter 2 repairing of vulcan coupling 3 repairing of alternator 4 o / h & repairing of turbocharger 5 repairing of water pump 6 repairing of cam shaft 7 repairing of lub oil pump 8 repairing of small carden shaft 9 repair / calibration of injectors 10 repair / calibration of fuel injection 11 repairing of air compressor 12 repairing of cylinder head...

Uttar Pradesh Jal Nigam - Uttar Pradesh

34146613 tender for construction of 01 no. rebore tubewell 300x200 mm dia 180/200 mtr. deep 1300 lpm by rcidc rig machine including development by 350 psi air compressor and o.p unit at 26th pac residential colony gorakhpur under deposit work programme...

North Eastern Railways - Uttar Pradesh

34111706 auction sale of diesel driven rotary type air compressor, model no. : cps325, make : chicago with original paper. not fit for railway use. 01 no....

Indian Oil Corporation Limited - Uttar Pradesh

34109441 bids are invited for 75 lpm capacity spin on oil filter element for filter head part no. 271.01.329.50 , element of air suction filter kfa 02 1 7036 , air oil separator element , gasket for air oil seperator , gasket for air end delivery , gasket for air intake valve , o ring id 56 x 3.55 dia , o ring one fourth of inch , o ring three eighth supply of spares for kirlosksar screw air compressor of inch , o ring half inch , o ring three fourth of inch , oring one inch , o ring one and a half inch , air intakevalve kit service, refer 273.02.084.50, r3 , ventingvalve kit repair, refer 273.02.085.50 , mpvl kitservice 273.02.554.50, r3 , k smart premium screwcompressor fluid 20l bucket , freight for spares forthree compressors total quantity : 135...

Bharat Heavy Electricals Limited - Uttar Pradesh

34108059 e auction for thediesel hydraulic f 15 escort 14mt hydra chasis no: 1693003413, model : 2004 registration no: hr 67/4172, construction elevator set, make mekaster, h 483/2008, portable air compressor (sl.no.20807003), air compressor with accessories (indersoll rand make), steam blowing device for lpbp system, acid cleaning pump, induction heating machines, escorts pick & carry 14 mt hydra crane (sl no.1694010213, make 2006) etc available at different sites of bhel psnr...

Bharat Heavy Electricals Limited - Uttar Pradesh

34076148 supply of oem spares for air comprassor and air dryer make elgi oem spares for air comprassor and air dryer make elgi , spin on filter part no. b004800770001, for elgi make screw compressor, model:e 22 10 , air filter part no. b005700770005, for elgi make screw compressor, model:e 22 10 , separator element, part no. 010350060, for elgi make screw compressor, model:e 22 10 , solenoid valve rotex, part no. b738207, for elgi make screw compressor, model:e 22 10 , kit moisture sep., part no. 010442250, for elgi make screw compressor, model:e 22 10 , elgi air lube, ( in 20 litres container ) part no. 00099805a, for elgi make screw compressor, model:e 22 10 , air filter assembly part no.: b004700770008 for screw air compressor model:e04 10 make: elgi...

Department of Defence Production - Uttar Pradesh

34075382 bids are invited for bearing main[ pr] pt. no. 35110120 spare for k. g. khosla make air comp. model 2ha4ter sl. no. 7124 fre (q3) , bearing big end[ pr] pt. no. 35110100 sparefor k. g. khosla make air compressors model2ha4ter sl. no (q3) total quantity : 70...

Nagar Palika Parishad - Uttar Pradesh

34067721 supply and construction of new tubewell 225 mm pvc pipe housing and 100 mm ms delivery de deep by percussion ring machine and dovelopment of borting by air compressor and op unit to ger stand free discharge at site at moh tarai ward no 12...

Nagar Palika Parishad - Uttar Pradesh

34067369 supply and construction of new tubewell 225 mm pvc pipe housing and 100 mm ms delivery de deep by percussion ring machine and dovelopment of borting by air compressor and op unit to ger stand free discharge at site at moh tarai ward no 25...

North Eastern Railways - Uttar Pradesh

34062916 supply of mechanical ( c&w ) itemmechanical ( c&w ) item, inflatable air bag with hp air compressor as per attached technical specification make jyotech engineering, sava or similar...

Indian Army - Uttar Pradesh

34062145 bids are invited for air compressor , dental handpiece , air water tubing , air air compressor rotor coupling total quantity : 6...

Indian Oil Corporation Limited - Uttar Pradesh

34056682 amc of screw air compressor annual maintenance contract non comprehensive type for 3 nos of kpcl make screw compressors 2 nos of kes45 model and 1 nos of kes55 model installed at indane bottling plant lucknow....

Uttar Pradesh Jal Vidyut Nigam Limited - Uttar Pradesh

34048505 complete servicing of 07 nos. different make air compressors along with supply of compressor spares at ( 3x33 mw ) hydel obra power station. 1 complete servicing of 02 nos. k.g khosla make ( model no.ab 11 ) air compressors along with supply of spares as mentioned in tender documents 2 complete servicing of 04 nos. ingersoll rand make air compressors of model no. 1a231 along with supply of spares as mentioned in tender documents. 3 complete servicing of 01 nos. elgi make ( model no. elgi 37 / 7.5 ) air compressor along with supply of sparesas mentioned in tender documents....

Banaras Locomotive Works - Uttar Pradesh

34045540 supply of air compressor ( water cooled ) for hhp locomotiveair compressor ( water cooled ) for hhp locomotive, air compressor ( water cooled ) for hhp locomotive this is a safety item as per drg.no. 40017843 alt a as per specn. specification for claening, surface / rust preventive, i mark and packing conditions misc:458...

North Central Railway - Uttar Pradesh

34025016 fixing of seamless m.s. pipe line from diesel air compressor to yard of gmc wagon depot in pryj division and fabrication of heavy duty industrial storage rack at site i.e. sick line gmc roh depot in pryj division....

North Eastern Railways - Uttar Pradesh

34020542 supply of air compressor ( auxilliary ) . as per specn. as per clw spec no. clw / es / c 4.air compressor ( auxilliary ) . as per specn. as per clw spec no. clw / es / c 4., air compressor ( auxilliary ) . as per specn. as per clw spec no. clw / es / c 4....

Northern Railway - Uttar Pradesh

34005406 supply of set of accessories for air compressorset of accessories for air compressor, set of accessories for air compressor ( sullair make ) as below: ( a ) deluxe supervisor microprocessor controller 01nos ( one nos ) . ( b ) temperature transducer 01 nos ( one nos ) . input voltage 110vac %b1 15% ( 47 63hz ) , ambient operating temp. 0 to 55%bac with installation & commissioning. sr. section uttar pradesh 1.00 set...

Department of Defence Production - Uttar Pradesh

33955349 bids are invited for spare for air compressor lubricator s/a 4element part no. 35020080. (q3) , spare for air compressor intermediate plate dia 310mm for cylinder, pt. no.35337110 (q3) , spare for air compressor ringpacking gland pt. no. 35296041 (q3) total quantity : 82...

Indian Army - Uttar Pradesh

33936979 bids are invited for lv7tmb 2786 1399 9916 gasket kit cyl head air compressor , lv7tata 3120 104492 bushing sleeve , lv7tmb 6222 030012 lamp 12v 2w black out lamp rear ts 29201 , lv7tmb 6212 3055 093 fuse 20a yellow , lv7tmb 2751 1540 8701 brush earth , lv7tmb 3501 0308 109 spanner de 8 x10 , lv7tmb 2698 5470 0108 assy switch ac on off , lv7tata 5306 056693 bolt 4 , lv7tmb 4710 000164 rubber elebow water line to thermostat , lv7tmb 2702 8240 9972 wiper blade front driver co driver , lv7tmb 2540 001963 piston , lv7tmb 2782 4660 0103 assy steering oil reservoir , lv7tmb 5330 019226 spacer ring swivel head , lv7tata 2614 6250 0105 assy face side rh , lv7tmb 2520 012585 assy clutch pressure plate 330 dia , lv7tmb 06000 50761 80750 sliding glass , lv7tmb 2698 8340 0187 thermostat...

North Central Railway - Uttar Pradesh

33916076 fixing of seamless m.s. pipe line from diesel air compressor to yard of gmc wagon depot in pryj division and fabrication of heavy duty industrial storage rack at site i.e. sick line gmc roh depot in pryj division....

North Central Railway - Uttar Pradesh

33890701 supply, installation and commissioning of portable air compressor with dryer & receiversupply, installation and commissioning of portable air compressor with dryer & receiver, supply, installation and commissioning of portable air compressor with dryer & receiver 500 ltrs. capacity 100 cfm @ 12.5 kg / cm2 . make elgi, atlas copco, kirloshkar, veekers, ingersoll rand or the international brand with prior approval of railway. technical specifications, warranty & spares as per annexure a. => limited...

Indian Army - Uttar Pradesh

33854190 bids are invited for lv7stln vf 5680 72 0000268 weather strip w strip back window side , lv7stln vf 24631000023 uc bearing pin , lv7stln vf b 7762007 sa of pipe inj no 4 , lv7stln vf 4730 72 0001009 elbow pipe to hose , lv7stln 2910 001746 hand primer , lv7stln vf 2530 017945 parts kit drag link tie rod , lv7stln p 3700752 9030 1391 stator assy , lv7stln vf 4720 72 0000428 hose non metalic , lv7stln 2530 018123 p 1007451 air compressor repair kit , lv7stln f 7413200 graduated flick valve , lv7stln x 7478300 boost pressure sensor 152 kw , lv7stln vf f 0254910 needle roller bearing , lv7stln f 3923600 sa of hose m22uxm22u 600 long , lv7stln f 7490200 ammeter , lv7stln vf b4381364 sa of hose , lv7stln p1605751 kit slave cylinder , lv7tmb 2614 3210 0106 assy front sprg...

North Central Railway - Uttar Pradesh

33845265 supply of air filter element suitable for electric air compressor make kirloskar model kes 75 7.5.air filter element suitable for electric air compressor make kirloskar model kes 75 7.5.,air filter element suitable for electric air compressor make kirloskar model kes 75 7.5. => limited...

North Central Railway - Uttar Pradesh

33845263 supply of air oil seperator element with gaskets suitable for electric air compressor make kirloskar model kes 75.7.5.air oil seperator element with gaskets suitable for electric air compressor make kirloskar model kes 75.7.5., air oil seperator element with gaskets suitable for electric air compressor make kirloskar model kes 75.7.5. => limited...

North Central Railway - Uttar Pradesh

33845092 supply of oil filter element suitable for air compressor make kirloskar model kes 75 7.5.oil filter element suitable for air compressor make kirloskar model kes 75 7.5.,oil filter element suitable for air compressor make kirloskar model kes 75 7.5. => limited...

North Central Railway - Uttar Pradesh

33844147 supply of k smart premium screw compressor fluid,(in 20.litre pack) suitable for electric air compressor make kirloskar model kes 75 7.5 as per attached detailsk smart premium screw compressor fluid,(in 20.litre pack) suitable for electric air compressor make kirloskar model kes 75 7.5 as per attached details,k smart premium screw compressor fluid,(in 20.litre pack) suitable for electric air compressor make kirloskar model kes 75 7.5 as per attached details => limited...

Indian Oil Corporation Limited - Uttar Pradesh

33803415 annual electrical maintenance contract for amc of pmcc annual electrical maintenance contract for amc of pmcc dg sets air compressor house fire water pump house entire lighting system other miscellaneous electrical maintenance jobs at indane bottling plant etawah => limited...