Uttar Pradesh Power Transmission Corporation Limited - Uttar Pradesh

39849543 work electrical , work of carriage of materials from different substation to 132 kv s / s augasi for 33 kv amlikaur bay under etd banda 2 loading of 06 nos of 33 kv ct along with ct junction box at 220 kv s / s banda 3 loading of 01 no acsr panther drum ( 1.5 km ) at 220 kv s / s banda & different size of ms flat 4 safe carriage of 06 nos of 33 kv ct along with ct junction box, 1 no acsr panther conductor drum ( 1.5 km ) and different size of ms flat from 220 kv s / s banda to 132 kv s / s augasi. 5 unloading of 06 nos of 33 kv ct along with ct junction box at 132 kv s / s augasi 6 unloading of 01 no acsr panther drum ( 1.5 km ) at 220 kv s / s banda & different size of ms flat 7 loading of 04 nos of 33 kv isolator with post insulator at 132 kv s / s pailani 8 carriage of 04 nos of 33 kv isolator with post insulator from 132 kv s / s pailani to 132 kv s / s augasi 9 unloading of 04 nos of 33 kv isolator with post insulator at 132 kv s / s augasi 10 loading, safe carriage & unloading of 01 km 2 c control cable ( 2 drum ) from 132 kv s / s karvi to 132 kv s / s augasi. 11 rates qouted by the bidders shall be without taxes. taxes applicable if any to paid extra...

Purvanchal Vidyut Vitaran Nigam Limited - Uttar Pradesh

39847466 supply of de centralized material supply of de centralized materila under edc maharajganj , supply of de centralized materials , , supply of cross arm holding clamps with bolts & nuts as per speicification. , supply of f bracket of fitting top insulator with bolts & nuts as per speicification. , supply of clamps with nuts & bolts for top channel as per speicification. , supply of off size nuts & bolts with washer as per speicification. , supply of pg clamps dog to dog conductor as per speicification. , supply of lt clamp with nuts & bolts of pcc pole with neutral as per speicification. , supply of lt shackel insulator 100x115 mm as per speicification. , supply of lt shackel strip with bolt & nut for lt section pole as per speicification. , supply of neutral cum earth wire gi wire 7.16 mm or 6 swg as per speicification. , supply of aluminium jointing sleave for aaac conductor weasel / rabbit as per speicification. , supply of aluminium jointing sleave for acsr conductor weasel / rabbit as per speicification. , supply ofspacer lt pvc as per speicification. , supply of holding clamps for top channel tpmo & fuse set etc. with bolts & nuts as per speicification. , supply of silica gel blue colour as per speicification. , supply of fuse wire for 100 kvad / tas per speicification. , supply of fuse wire for 250 kva d / t as per speicification. , supply of fuse wire for 400 kva d / t as per speicification. , supply of fuse wire for 5 mva power transformer as per speicification. , supply of aluminium lug of 185 sqmm as per speicification. , supply of aluminium lug of 250 sqmm as per speicification. , supply of aluminium lug of 300 sqmm as per speicification. , supply of aluminium lug of 400 sqmm as per speicification. , supply of 11kv vcb spout as per speicification....

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39845156 various electrical work of electric supply in the area of eudsd iind, etah ( eudd, etah ) under additional business plan ( 339 cr. ) on semi turnkey basis. 2 danger board with barbed wire including jumpering 3 dead end clamp 4 holding clamp for top chanel 5 i hook 6 lt pin clamp for pcc 7 ms droper chanel 8 ms top chanel with clamp 9 nut and bolt with washer 10 stone pad 11 suspension clamp 12 lt incoming panel with metering equipment 13 copper l piece 14 alluminium lug 15 alluminium paint 16 red oxide paint 17 tf base angle 18 prc connector 19 t chanel clamp 20 t chanel 21 lt protection for dt ( mccb ) 22 lt protection of dt 23 dc converter with battery 24 tripping coil for vcb 25 erection work : 26 safe carriage of line material from store center etah to pit site in distance range 0 to 10 km including loading & unloading at both ends. 27 safe carriage of vcb from store center etah to pit site in distance range 0 to 10 km including loading & unloading at both ends. 28 ( a ) 11 kv vcb outgoing / incoming 29 ( b ) 33 kv vcb outgoing 30 safe carriage of33 kv / 11 kv ct from store center etah to pit site in distance range 0 to 10 km including loading & unloading at both ends. 31 safe carriage of 8.5 mtr long pcc pole from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 10 kms.including loading and unloading at both side 32 safe carriage of 11 mtr long st pole from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 10 kms.including loading and unloading at both side 33 safe carriage of following tf from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side. 34 ( a ) 63 / 100 kva tf 35 ( b ) 250 / 400 kva tf 36 erection of 8.5 mtr long pcc pole as single support including fixing of ht / lt accessories etc and other work complete as per respo norms. 37 erection of 11 mtr long st pole as single support including fixing of ht / lt accessories etc and other work complete as per respo norms. 38 erection of 8.5 mtr long pcc pole as double pole / section pole including fixing of ht / lt accessories etc and other work complete as per respo norms. 39 erection of 11 mtr long st pole as double pole including fixing of ht / lt accessories with tpmo etc and other work complete as per respo norms. 40 mounting of following tf on double pole / single pole including making of the connection etc. complete. 41 ( a ) 63 / 100 kva tf 42 ( b ) 250 / 400 kva tf 43 laying, sagging stringing, binding, jumpering & fixing of all accessories etc of following conductor on the newly / old erected pole as per respo manual and as per direction of supervising engineer. it includes the cost of labour, t & p, carrier etc required for proper completion of work. 44 ( a ) acsr weseal conductor 45 ( b ) acsr dog conductor 46 ( c ) lt abc cable 3x120 sqmm 47 ( d ) lt abc cable 3x95 sqmm 48 ( e ) lt pvc cable 1x400 sqmm 49 ( f ) lt pvc cable 1x240 sqmm 50 ( g ) lt pvccable 1x630 sqmm 51 ( h ) lt pvccable al 3.5x150 sqmm 52 earthing complete 53 11 kv vcb o / g ctr 200 / 100 / 5amp, 350 mva 54 11 kv vcb i / c ctr 600 / 300 / 5amp 55 3 phase distribution box 56 33 kv control panel i / c single tf 57 construction of 250 / 400 kva t / f plinth all cost of labour and t&p which required for completion of work 58 net fencing shall be 1150*1200 mm made of 35*35 mm ms angle covered by expended netal 14 swg up to full height 1200 mm duly steftened by ms flat by an 8 swg dia bolt & nut 59 pipe earthing of 250 / 400 kva medium power transformers 60 33 kv vcb outgoing ct 400 / 200 / 5a 61 33 kv ct, o / g 400 / 200 / 1amp 62 11 kv ct o / g 400 / 200 / 5amp 63 11 kv ct i / c 600 / 300 / 5amp 64 33 kv lighting arrestor 65 33 kv fuse set 66 danger board with barbed wire including jumpering 67 dead end clamp 68 stone pad 69 fixing / erection oflt incoming pannel with metering equiptment, grouting as per respoo manual all cost of labor, material and t&p which required for completion of work 70 tripping coil for vcb 71 lt production for dt ( mccb ) 72 lt production for dt 73 4 core lt mcb with box 74 alluminium paint 75 red oxide paint 76 33 kv cable jointing kit outdoor 3x300 sqmm 77 33 kv cable straight through outdoor 3x300 sqmm 78 erection and grouting of stays as per respo norms and as per direction of supervising engineer. grouting material i.e. cement, sand, brick ballast / stone ballast etc. shall be arranged by the contractor at his own cost. 79 any other material / consumable required to complete the work shall be arrange by the contractor at his own cost. 80 carriage of old line material from pit site to je store / store center etah in distance range 0 to 10 km. including loading & unloading and proper stacking. 81 ( a ) 11 kv vcb 82 ( b ) 33 kv control panel...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39844018 various electrical work of electric supply in the area of eudsd ist, etah ( eudd, etah ) under additional business plan ( 339 cr. ) on semi turnkey basis. 2 danger board with barbed wire including jumpering 3 dead end clamp 4 holding clamp for top chanel 5 i hook 6 lt pin clamp for pcc 7 ms droper chanel 8 ms top chanel with clamp 9 nut and bolt with washer 10 stone pad 11 suspension clamp 12 lt incoming panel with metering equipment 13 copper l piece 14 alluminium lug 15 alluminium paint 16 red oxide paint 17 tf base angle 18 prc connector 19 t chanel chanel clamp 20 t chanel 21 tripping coil for vcb ( areva ) 22 tripping coil for vcb ( stelmac ) 23 lt protection for dt ( mccb ) 24 lt protection for dt 25 dc converter with battery 26 erection work : 27 safe carriage of line material from store center etah to pit site in distance range 0 to 10 km including loading & unloading at both ends. 28 safe carriage of33 kv vcb from store center etah to pit site in distance range 0 to 10 km including loading & unloading at both ends. 29 ( a ) 11 kv vcb outgoing / incoming 30 ( b ) 33 kv vcb 31 safe carriage of33 kv / 11 kv ct from store center etah to pit site in distance range 0 to 10 km including loading & unloading at both ends. 32 safe carriage of 8.5 mtr long pcc pole from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 10 kms.including loading and unloading at both side 33 safe carriage of 11 mtr long st pole from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 10 kms.including loading and unloading at both side 34 safe carriage of following tf from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side. 35 ( a ) 250 / 400 kva tf 36 ( b ) 100 kva tf 37 ( c ) 16 kva tf 38 erection of 8.5 mtr long pcc pole as single support including fixing of ht / lt accessories etc and other work complete as per respo norms. 39 erection of 11 mtr long st pole as single support including fixing of ht / lt accessories etc and other work complete as per respo norms. 40 erection of 11 mtr long st pole as double pole including fixing of ht / lt accessories with tpmo etc and other work complete as per respo norms. 41 mounting of following tf on double pole / single pole including making of the connection etc. complete. 42 ( a ) 250 / 400 kva tf 43 ( b ) 100 kva tf 44 ( c ) 16 kva tf 45 laying sagging stringing, binding, jumpering & fixing of all accessories etc of following conductor on the newly / old erected pole as per respo manual and as per direction of supervising engineer. it includes the cost of labour, t & p, carrier etc required for proper completion of work. 46 ( a ) acsr weseal conductor 47 ( b ) lt abc cable 3x120 sqmm 48 ( c ) lt abc cable 3x95 sqmm 49 ( d ) lt pvc al cable 3.5x150 / 3.5x400 sqmm 50 ( e ) cable 4x2.5 sqmm 51 earthing complete 52 11 kv vcb o / g ctr 200 / 100 / 5amp, 350 mva 53 11 kv vcb i / c ctr 600 / 300 / 5amp 54 3 phase distribution box 55 33 kv control panel for double tf 56 construction of 250 / 400 kva t / f plinth all cost of all cost of labour and t&p which required for completion of work 57 net fencing shall be 1150*1200 mm made of 35*35 mm ms angle covered by expended netal 14 swg up to full height 1200 mm duly steftened by ms flat by an 8 swg dia bolt & nut 58 pipe earthing of 250 / 400 kva medium power transformers 59 33 kv vcb 800 amp, 750 mva 60 33 kv ct, 400 amp / 200 / 1 1 1 amp 61 11 kv ct i / c 600 / 300 / 5amp 62 11 kv ct o / g 400 / 200 / 5amp 63 33 kv lighting arrestor 64 33 kv fuse set 65 danger board with barbed wire including jumpering 66 dead end clamp 67 stone pad 68 fixing / erection oflt incoming pannel with metering equiptment, grouting as per respoo manual all cost of labor, material and t&p which required for completion of work 69 tripping coil for vcb ( areva ) 70 tripping coil for vcb ( stelmac ) 71 lt production for dt ( mccb ) 72 lt production for dt 73 4 core lt mcb with box 74 single core pvc cable 1x240 75 single core pvc cable 1x400 76 single core pvc cable 1x630 77 erection and grouting of stays as per respo norms and as per direction of supervising engineer. grouting material i.e. cement, sand, brick ballast / stone ballast etc. shall be arranged by the contractor at his own cost. 78 any other material / consumable required to complete the work shall be arrange by the contractor at his own cost. 79 carriage of line material ( scrap ) from pit site to je store / store center etah in distance range 0 to 10 km. including loading & unloading and proper stacking. 80 ( a ) 11 kv vcb outgoing 81 ( b ) 10 kva transformer ( old ) 82 ( c ) 100 kva transformer ( old ) ...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39841071 various electrical work of electric supply in the area of edsd ( jaithra ) , etah ( edd ist, etah ) under additional business plan ( 339 cr. ) on semi turnkey basis. 2 nut & bolt with washer 3 33 kv cable jointing kit o / d 4 ms droper chanel 5 stone pad 6 top chanel 7 holding clamp for top chanel 8 ms t off chanel 9 danger board 10 protection board for power tf 11 tripping coil for vcb 12 33 kv jointing kit straight thourgh 13 base angle 14 erection work : 15 safe carriage of line material from store center etah to pit site in distance range 0 to 60 km including loading & unloading at both ends. 16 safe carriage of 11 kv xlpe cable 3x120 sqmm from store center etah to pit site in distance range 0 to 60 km including loading & unloading at both ends. 17 safe carriage of 33 kv vcb from store center etah to pit site in distance range 0 to 60 km including loading & unloading at both ends. 18 safe carriage of 9 / 8.5 mtr long pcc pole from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side 19 safe carriage of following tf from electricty store center etah / nearest 33 / 11 kv s / s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side. 20 ( a ) 25 / 63 kva tf 21 ( b ) 100 kva tf 22 erection of 9 mtr long pcc pole as single support including fixing of ht / lt accessories etc and other work complete as per respo norms. 23 erection of 8.5 mtr long pcc pole as double pole / section pole including fixing of ht / lt accessories with tpmo etc and other work complete as per respo norms. 24 dismantling and removal of existing acsr dog conductor conductor from the various area, stacking and placement their coils and their in the safer place including cost of lobour t&p etc. required for proper completion of work. 25 laying sagging stringing, binding, jumpering & fixing of all accessories etc of following conductor on the newly / old erected pole as per respo manual and as per direction of supervising engineer. it includes the cost of labour, t & p, carrier etc required for proper completion of work. 26 ( a ) acsr dog conductor 27 ( b ) 11 kv xlpe cable 3x120 sqmm 28 re sagging of looseweseal / dog conductor as per direction of supervising engineer. it includes the cost of labour, t & p carrier etc required for proper completion of work. 29 stone pad 30 earthing complete 31 33 kv cable jonting kit o / d 32 33 kv cable jonting kit straight through 33 danger board with clamp 34 power board power tf 35 tripping coil for vcb 36 33 kv lighting arrestor 37 33 kv vcb 800 amp, 750 mva 38 erection and grouting of stays as per respo norms and as per direction of supervising engineer. grouting material i.e. cement, sand, brick ballast / stone ballast etc. shall be arranged by the contractor at his own cost. 39 mounting of following tf on double pole including making of the connection etc. complete. 40 ( a ) 25 / 63 kva tf 41 ( b ) 100 kva tf 42 any other material / consumable required to complete the work shall be arrange by the contractor at his own cost. 43 carriage of line material ( scrap ) from pit site to je store / store center etah in distance range 0 to 60 km. including loading & unloading and proper stacking. 44 ( a ) acsr dog conductor 45 ( b ) 100 kva transformer....

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39835516 tender for work for transformer earthing under edd i baraut 1 removing of damaged packing of h.v. / l.v. & neutral side bushing and replacement with new gaskets, its fixing after proper cleaning. 2 opening of radiators and repairing, fixing its with new gasket, packing 3 replacement of damaged oti, wti of 05 m.v.a. power transformer. 4 replacement of damaged oti, wti of 10 m.v.a. power transformer. 5 replacement of damaged 33 kv isolator jaw made of electrolyte copper strip for isolator bladefitted gi frame with connectiong plate of size 75*6 mm with holes for fitting and tightening of 33 kv isolator clamps for acsr panther conductor. all material shall be supplied by the contractor. 6 replacement of damaged islolator blade 1200 amp made of electrolyte copper flat 1.0 m long size 32*5 mm.all material will be supplied by contractor. 7 replacement of complete top cover gasket 8 centrifuging of tansformer oil of 10 m.v.a. power transformer installed at 33 / 11 k.v. sub station. 9 body and neutral earthng of 05 mva transformer ( 33 kv / 11 kv ) by making bores including providing of 1.5 dia a class pipe and g.i. strip 50x6 mm and other required materials and work to complete the work satisfactorily...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39835219 tender for providing transformer trolley under eudd ii sre 1 safely carriage of upto 400 kva t/f frompvvnl, store to site including loading and unloading at both ends. 2 mounting and safely installation of 400 kva t/f on trolly as per resspo norms. 3 safely carriage of lt xlpe cable 1x400sqmm from pvvnl, store to site of work including loading & unloading at both ends & fixing of 400kva t/f lt side. 4 safely carriage of acsr dog condutor from pvvnl, store to site of work including loading & unloading at both ends & fixing of 400kva t/f ht side. 5 providing & fixing of ms angle 65x65x6 as per resspo norms. 6 providing & fixing of ms channel 100x50x6 as per resspo norms. 7 providing & fixing of 11kv fuse set as per resspo norms. 8 providing & fixing holding clamp with nut & bolt as per resspo norms. 9 providing & fixing of aluminium lugs suitable for lt xlpe cableas per resspo norms. 10 providing & fixing of aluminium bolted lugs suitable for lt xlpe cableas per resspo norms. 11 providing & fixing different type nut & bolt as per site condition. 12 providing wheel base trollysuitable for 400kva transformer as per attached specification. ...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39834963 tender for increasing capacity of substation kaniyan ( shamli ) from ( 1×5 ) mva to ( 2×5 ) mva. 1 1. supply of following material33kv bus isolator 800 amp. 2 galvanized structure for 33 kv isolator with plinth & foundation 3 galvanized structure 33 kv single phase ct ( 3 nos. ) with plinth & foundation with junction box 4 galvanized structure for 33 kv vcb with plinth & foundation 5 pg clamp for dog to panther 6 33kv post insulator 7 galvanized structure for 33 kv post insulator ( 3 nos. ) with plinth & foundation 8 33 kv fuse set 9 galvanized structure for 33 kv fuse set 10 33kv lightning arrestor with surge counter. 11 galvanized structure for 33 kv lightning arrester ( 3 nos. ) with plinth & foundation 12 supply of 90 lbs rail pieces for t / f ( 44.64kg / mtrs. ) 13 supply for cable support galvanised structurei ) galvanised channel ( 100x50x6 ) mm 14 ii ) galvanised angle ( 50x50x6 ) mm 15 ii ) galvanised angle ( 65x65x6 ) mm 16 supply of copper bus bar of size ( 2500x50x6 ) mm 17 pvc control cable 2×2.5 mm² mtr. 18 pvc control cable 4×2.5 mm² mtr. 19 supply of g.i. strip size 50x6mm for earthing of outdoor & indoorequipment 20 2. m.s. round 32 mm dia 21 11 kv fuse set 22 rubber mat of size 1×2×.02m 23 100mm dia gi pipe 3mtr long 24 heat shrinkable outdoor type end termination cable jointing kit suitable for 11kv xlpe 3x300 sq.mm. cable 25 heat shrinkable indoor type end termination cable jointing kit suitable for 11kv xlpe 3x300sq.mm. cable 26 supply for water level earthing a ) g.i. pipe size 40 mm inner dia & thickness 2mm 27 b ) solid copper cone approx 225 mm long and 750 gm in weight 28 c ) copper wire 6 swg 29 d ) copper flexible earthing strip of size 50x6mm for neutral 30 safe carriage of following stock material from any stores centres under pvvnl, depending upon the availability of material at stores centres, with loading & unloading at both ends respectively.a ) 33 / 11 kv, 5mva transformer 31 b ) 11kv xlpe cable 3x300mm² 32 d ) 11kv incoming vcb ctr 600 / 300, 5amp 33 f ) 33 kv c.t 400 / 200 1a 34 g ) acsr dog conductor 35 h ) 33 kv vcb 800 amp, 750 mva with steel structure 36 i ) control panel i / c for 33 kv single t / f 37 miscellaneous civil works of increasing capacity of 33 / 11 kv substation kaniyan ( shamli ) from ( 1×5 ) mva to ( 2×5 ) mvaconstruction of plinth for 33 / 11kv t / f of ( 3.46x4.46x1.0 ) m 0.5 m above ground level ) as per details: a ) supply of 90 lbs rail pieces for t / f ( 44.64kg / mtrs. ) 38 b ) supply & erection of 1st class brick work for side walls size 0.23 m wide upto 0.35 m heightcm c.c. ratio of 1:4 ( cement & fine sand ) 39 c ) supply & filling of brick ballast in plinth in ratio 1:4:8 ( cement, coarse sand & brick ballast ) with proper ramming. size ( 3.0x4.0x0.65 ) m. 40 d ) supply & erection of r.c.c. work on the top of plinth in ratio 1:2:4 in ( 3.46x4.46 ) m size and 0.20m in thickness by using m.s. tor of 12 mm dia. 12 nos. in each direction across to each other & m.s.channel ( 125x65x6mm ) 52kgs. the work also includes cutting, bending of m.s. tor etc. 41 e ) supply & erection of quantity of m.s. tor of size 12 mm dia required for reinforcement of plinth in r.c.c. work, work also includes cutting, winding and laying etc. in the t / f plinth. 42 f ) grouting of 01 nos. 90 / 105 lb. rail pieces of 3.46m long and ( 50x50x6 ) mm m.s. angle in r.c.c. work at the top of plinth work also includes cutting of rail and angles pieces etc. 43 g ) supply & erection of 12mm thick plaster with cement mortar ratio 1:4 ( cement & fine sand ) of plinth of 0.4m upper side. 44 plinth for 33 kv v.c.b.construction of plinth for the structure of 33 kv vcb & c.t.s as per details for 01 no.: a ) excavation of earth of size ( 2.4x1.5x1.0 ) m pits for construction of plinth. 45 b ) brick ballast ratio ( 1:3:6 ) ( cement, sand & stone grift for foundation work ( 2.4x1.5x0.15 ) m plinth. 46 c ) r.c.c. work in ratio 1:2:4 ( cement, coarse sand & stone grit of 20mm size ) for making plinth of size ( 2.4x1.5x1.0 ) m and grouting of foundation bolts 04 nos. for 33 kv vcb. 47 d ) 12mm thick plaster with cement mortar in ratio 1:4 ( cement & fine sand ) of plinth of side size ( 2.4x1.5x0.4 ) m. 48 e ) laying of g.i.earth strip of size 50x6mm for connecting the earth mat with steel structure. the work also includes cutting, bending, straigthning, over lapping and welding the earth strip with earth mat and various steel structures by using high quality arc welding in already digged trenches. 49 f ) painting of earth strip of size ( 50x6 ) mm with one coat of ready mixed primer with two coats of isi mark synthetic oil enamal green paint. 50 construction of control cable trench as per details a ) excavation of earth in size 0.650×0.40×25m. 51 b ) c.c. work in foundation in ratio 1:4:8 ( cement, sand & brick ballast ) with proper ramming in size 0.650×0.15 mt. 52 c ) first class brick work in cement mortar in ratio 1:4 in size 0.23×0.32 mtr. 53 d ) 25 mm thick c.c. in floor of cable trench in ratio 1:2:4 ( cement, coursend and stone ballast ) 20mm gauge in size 0.3 mtr. width 54 e ) grouting of m.s. strip of size 450×25×6mm in cable trench 100mm above floor level and at equal space distance 300mm 55 f ) plastering of trench in cement, mortar in ration 1:4, 12mm thick in cable trench. 56 g ) fabrication and fixing cable trench cover of m.s. angle iron size 40×40×6mm of size 0.3m wide 0.5 to 1.0 mtr. length with proper welding of 8 mm size of bar 2 nos. in length and 6 nos. in width. 1.00 mtr. long 57 control cable laying a ) laying of different size of ( 2×2.5 ) mm2 control cables i.e. from buchholz realy to marshalling box marshalling box to switch gear room, 33 kv cts to cts ct 33 kv, v.c.b. control panel junction box to 33 kv vcb control panel and control panel to 33 kv vcb outdoor operating mechanism panel from t / f etc. in the cable trench including making proper connection at buchholz relay, marshalling box as per required for installed equipment. 58 b ) laying of different size of ( 4×2.5 ) mm2 control cables i.e. from buchholz realy to marshalling box marshalling box to switch gear room, 33 kv cts to cts ct 33 kv, v.c.b. control panel junction box to 33 kv vcb control panel and control panel to 33 kv vcb outdoor operating mechanism panel from t / f etc. in the cable trench including making proper connection at buchholz relay, marshalling box as per required for installed equipment. 59 10. miscellaneous electrical works of increasing capacity of 33 / 11 kv substation kaniyan ( shamli ) from ( 1×5 ) mva to ( 2×5 ) mva. installation of 33 / 11 kv, 5 mva transformer :i ) shifting of available 5 mva 33 / 11 kv, transformer to transformer plinth in switch yard. 60 ii ) erection of shifted transformer at plinth by fixing all accessories like radiators, conservator tank, filling the transformer oil to desired level and ensuring that there is no leakage, complete job in all respect. 61 water level earthing by boring and lowering of g.i. pipe size 40 mm dia & thickness 2mm into the ground at 20 mtr depth or upto the water level with the lower end of solid copper cone approx 225 mm long and 750 gm in weight shall be provided and screwed in pipe as well as bringing out a continuous copper wire 6 swg from the cone up to the ground surface where it will be bolted to the g.i. earth strip for transformer neutral connection, the earth strip will be welded to the g.i. pipe and neutral earthing support. 62 fabrication and erection of neutral earthing l type support made of g.i. channel size 100x50mm. structure shall be 4 mtr. long with 1 mtr. arms and 0.75mtr bracing. structure shall be grouted in ratio 1:3:6 in block size 300x300x1000mm including plinth and painted with one coat of ready mixed primer and two coat of enamel aluminium paint work includes connecting neutral bushing rod of power transformer and g.i. earthing strip with the help of flexible copper bond, m.s. bolt and washer with stone pad of size ( 300x300x75mm ) . 63 fabrication and erection of cable support made of two pieces of g.i. channel ( 100x50x6 ) mm, 2.75 meter long, joined to each other by means of 5 nos. g.i. angle ( 50x50x6 ) mm pieces of size 0.75mtr long each by welding at equal intervals and grouting in a block of size ( 300x1000x1000 ) mm in c.c. 1:3:6 complete with one coat of ready mixed primer and two coats of al. paint. work includes providing of three nos. g.i. clamps made of ( 50x6 ) mm g.i. flat for holding the cable including nuts and bolts with stone pad of size ( 300x300x75mm ) . 64 fixing 110mm dia 2mm thick 2m long g.i.pipe over 11kv, 3x300sq.mm xlpe cable before mounting the 2no. cable on cable support structure. work includes fixing of clamp, sealing of top and bottom end of the g.i.pipe. one end of g.i.pipe is to be buried under earth about 500mm. 65 fabrication of copper bus bar of size ( 2500×50×6 ) mm in l.v. side of 10 mva 33 / 11 kv, power transformer. work includes connection of outside bus bar in l.v. side busing rod of power transformer and other side with outdoor 11 kv cable box as well as providing empire tape and h.t. tape etc. for proper insulation work. 66 h.t. power cable laying :i ) laying 11 kv, ( 3x300 ) / ( 3×185 ) mm2 xlpe cable from power transformer to 11 kv incoming switch gear and11 kv incoming switch gear to double pole in the cable trench and 0.45 m wide, 0.90m depth. providing 150 mm local sand for cushion beneath and 150 mm above the cable ( quality of local sand required 0.375 cum / m in length ) . the cable shall be dully protected by brick. on both side of cable by laying brick vertically and bricks would also be laid bricks along the cable ( minimum 18 nos. of bricks are to be laid top and outer side along the single cable. the work includes digging of trenches, laying of cable in under ground trenches, joining of terminals, back filling of earth and testing and commissioning of power cable etc. spare cable shall be left over and laid in the trenches in shape of 6 m ring at both ends. 67 ii ) laying and dressing of 11 kv ( 3x300 ) / ( 3×185 ) mm2 power cable in air / trench. 68 installation of 33 kv vcbassembling and installation of 33 kv vcb on the vcb out door structure on the plinth. adjustment of operating mechanism in proper alignment for smooth operation of the same. the work also includes fabrication of addition arrangement for proper fixing, if required. 69 installation of 33 kv isolators with structure:assembling and installation of bus isolator on the isolator structure. adjusting of operating mechanism in proper alignment so as to ensure smooth operation of the same. in case of line isolator proper operation of earth links shall also be ensured. the work includes fabrication for proper fixing if required. 70 installation of 33 kv c.t.s with structure:installation of 3 nos. c.t.s . the work includes fabrication for proper fixing, if required to complete the work. 71 installation of 33 kv post insulators with structure:installation of 06 nos. post insulatorson structure. the work includes fabrication for proper fixing, if required. 72 installation of 33 kv fuse set with structure:assembling and installation of fuse set on the fuse set structure. the work includes fabrication for proper fixing, if required. 73 13. installation of 33 kv lightening arrestors with structure: assembling and installation / mounting of 3 nos. lighting arrestors on the l.a.s structure / terminal gantry, complete with earthing and line connections. the work includes fabrication for proper fixing, if required. 74 installation of 33 kv control panel of single t / fassembling and installation of 33 kv vcb control panel of single t / f adjustment of operating mechanism in proper alignment for smooth operation of the same. the work also includes fabrication of addition arrangement for proper fixing, if required. 75 33 kv bus bar jumpering :stringing of 33 kv bus bar by using and laying acsr dog / panther conductor including fixing of 33 kv disc insulators and tension fittings to complete work with proper sagging of bus bar etc. 76 installation of 11 kv switch gears in control rooma ) carefully & safely shifting of 11 kv switch gears ( i / c 1n0, ) from outside to inside the switch gear room grouting foundation of bolts in c.c. ratio of 1:2:4 ( including cutting of rcc floor and finishing of rcc floor ) as per requirement placing, aligning and fixing of 11 kv anchor gi bolts and nuts of proper size for completion of work. 77 b ) proper fixing and making bus bar connection in between two switch gears ( i / c 1n0 ) after proper cleaning. work also include proper insulation, taping by empire, pvc and h.t. tape etc. 78 3 hiring of d / g set including carriage, loading, unloading & operating charges ( with fuel ) at 33 / 11 kv substation under construction in case l.t. supply is not available near s / s within prescribed accessible limit.63 kva, three phase, d / g set for fabrication of different structure at substation. 79 erection of following materiala ) heat shrinkable outdoor type end termination cable jointing kit suitable for 11kv xlpe 3x300 sq.mm. cable 80 b ) heat shrinkable indoor type end termination cable jointing kit suitable for 11kv xlpe 3x300sq.mm. cable 81 e ) painting of s / s structur 82 earthing of outdoor equipment, details as given below: a ) cutting of 32mm.dia m.s. bar 3mtr.long and making one end in conical shape by forging process and driving it into the earth at each corner of bridge outside control room and proper welding with m.s.bars. 83 b ) digging of pits for making delta by laying 32mm. dia m.s.round in tringle shape. electric welding on cross joints by providing “u” clamp in size 25×6mm. of m.s.flat, with over lap joint by providing m.s.round 12mm dia, on both sides of over lap joints of m.s.round, by electric welding. all joints shall be painted with black bituminious paint. 84 c ) earthing of 33kv la, neutral link structure, power t / f body ( both side ) by providing g.i.strip in size 50×6mm. with 32mm. dia m.s.round laid in trench with proper electric welding. 85 construction of sso approach road ( as per specification ) ...

Uttar Pradesh Power Transmission Corporation Limited - Uttar Pradesh

39834955 replacement of existing 132 k.v main bus of single acsr zebra conductor with twin acsr moose conductor including supply of of fittings, connectors, pg clamp, spacers etc. and replacement of 132 k.v. transfer bus coupler bay of single acsr panther conductor with single acsr moose conductor, replacment of defective 132 kv main bus p.t, 132 kv bus isolator & 132 k.v c.ts at 132 kv s / s s.g.p.g.i under e.t.d i, lucknow...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39834825 tender for provide transformer trolley under eudd i sre 1 safely carriage of upto 400 kva t / f frompvvnl, store to site including loading and unloading at both ends. 2 mounting and safely installation of 400 kva t / f on trolly as per resspo norms. 3 safely carriage of lt xlpe cable 1x400sqmm from pvvnl, store to site of work including loading & unloading at both ends & fixing of 400kva t / f lt side. 4 safely carriage of acsr dog condutor from pvvnl, store to site of work including loading & unloading at both ends & fixing of 400kva t / f ht side. 5 providing & fixing of ms angle 65x65x6 as per resspo norms. 6 providing & fixing of ms channel 100x50x6 as per resspo norms. 7 providing & fixing of 11kv fuse set as per resspo norms. 8 providing & fixing holding clamp with nut & bolt as per resspo norms. 9 providing & fixing of aluminium lugs suitable for lt xlpe cableas per resspo norms. 10 providing & fixing of aluminium bolted lugs suitable for lt xlpe cableas per resspo norms. 11 providing & fixing different type nut & bolt as per site condition. 12 providing wheel base trollysuitable for 400kva transformer as per attached specification....

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39832363 installation of different capacity distribution transformer ( additional 08 nos. 25 kva, 06 nos. 63 kva & 02 nos. 250 kva t / f ) the head of business plan year 2023 24 under edd iind / jaisinghpur / lambhua / kadipur, sultanpur ( different location ) along with safe carriage and installation for different material and associated work. 2 following materials supplied by the contractor : 3 l clamp (copper) 4 stone pad 5 clamp for top/t off/droper 6 suspension clamp 7 dead end clamp 8 eye hook clamp 9 red oxide paint 10 alluminium paint 11 safe carriage/cartage of following items from store centre, sultanpur to work site including loading, unloading and proper stacking and return back of balance material form site to store at sultanpur (distance within0 50 km.) 12 safe carriage of pcc pole 8.5 mtr. long 13 safe carriage of stp 11 mtr. long 14 safe carriage of acsr weasel conductor 15 safe carriage of lt pvc cable 1x400 sq.mm. 16 safe carriage of ab cable (3x50+1x35+1x16) sq.mm. 17 safe carriage of ab cable (3x120+1x35+1x16)sq.mm. 18 safe carriage of other line materials 19 safe carriage of t/f 25 kva 20 safe carriage of t/f 63 kva 21 safe carriage of t/f 250 kva 22 dragging of pcc pole from site to pit point 23 dragging of stp from site to pit point 24 fabrication & erection of double pole support on pcc pole including digging of pit & fixing of all accessories and clamps including croncreting, grouting & earthing of pole as per respo norms. also return back of balance material to store (if any). 25 fabrication & erection of st pole 11 mtr. support on st pole including digging of pit & fixing of all accessories and clamps including croncreting, grouting & earthing of pole as per respo norms. also return back of balance material to store (if any). 26 mounting of additional 25 kva t/f on double pole. 27 mounting of additional 63 kva t/f on double pole. 28 installation of 250 kva t/f on plinth and associated works. 29 construction of new plinth as per approved drawing for 11/0.4 kv 250 kva t/f including all requred man and material along with construction of fencing round the transformer plint including man and material and earthing of fencing. 30 stringing and sagging of lt pvc cable 1x400 sq.mm. from dt to double pole including all associated work, 31 stringing and sagging of ab cable (3x50+1x35+1x16) sq.mm. from dt to double pole including all associated work, 32 stringing and sagging of ab cable (3x120+1x35+1x16) sq.mm. from dt to double pole including all associated work, 33 laying stringing & sagging of acsr weasel conductor etc. 34 stay complete 35 providing and installation of pipe type earthing as per approved drawing including all requred man and material. 36 earthing of transformer through earthing rod as per approved drawing including all requred manpower. 37 providing and fixing of al. lug required size 38 supply and installation of various size nuts, bolts & washer ...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39832287 under electricity distribution division hamirpur under hundredth of girpur ( 1 ) 33 / 11 k.b. work of replacement of long wires and buzzer wires of various conductors under the power sub station kurara ( 2 ) 33 / 11 k.b. 100 kba power sub station in kurara. the work of making pindh in. 1 supply & erection 2 pcc pole 8.5 m long ( provided by department ) 3 stone pad 300x300x75 mm 4 x arm ms angle 65x65x6 mm v type 5 cross arm holding clamps with bolt & nut ( provided by department ) 6 11 kv pin insulator with pin ( provided by department ) 7 11 kv disc fitting 45 kn t &t&c ( provided by department ) 8 11 kv disc insulator ( provided by department ) 9 t off channel 10 clamp for channel 11 11 kv f clamp 12 earthing complete 13 concreating of stay 14 construction of plinth 11 / 0.4 kv 100 kva transformer plinth size of size 6x6x5 above ground level and one fit below the ground level of 9 after excavation of 4 earth brick ballast shall be provided and remaining will be done properly after that aretaining wall of width by the first class bricks in ration 1:5 of cement and sand shall me made the earth shall be filled upto one fit below 15 acsr weasel conductor ( provided by department ) 16 straightening of tilled pole 33 kv line at various place as per direction of supervising engineer including the cost of labour and t&p etc required for proper completion of work 17 dismentling of old line 18 loading unloading & cartage of old conductor work site to store center 19 stay set 16x1800 20 grouting of pole...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39832239 carrying out the 08 nos. work system strengthening ( dts fencing / dts plinth / replacement of meter panel box / replacement of feeder panel / lt acb / replacement of pole / dts earthing in area of eudsd ii / xiii, noida under eudd vii, noida in the juridiction of eudc i, noida ( additional business plan rs. 30.00 crore for noida zone ) . 1 providing and installation oflt acb600 amp. with cabinet / structure (make l&t, schneider, abb, hevells) as per following specification with all relevant certificate : 2 600 amp. 03 pole fixed manual acb. 3 red/yellow/blue light indication 4 on & off indication 5 amp., voltmeter& energy meter digital 6 metering c.t 400/5a, 7 panel fabrication of size 1250mm x 900mm x 600 mmmade of m.s sheet 14 gauge with powder coating with panel lock and key arrangement.(two nos). and additional locking arrangement seprately including providing hut type shape as per drg. 8 fabrication ofaluminium bus bar for each phases 9 incoming size 425 mm x 50mmx12 mm (twin) 10 out going size 720 mm x 50mm x 12 mm(twin) 11 neutral size 900mmx50mmx12 mm. 12 fabrication of pannel stand made of m.s angle of size 900mm x 600mm x 500 mm as per drg. 13 assembly of above acb, indicators, meters, metering ct & bus bar arrangment in the panel, fitting the panel on stand with nut and boltswith wiringetc. & grouting inratio 1:4:8 with cement, coarse sand and brick blast. 14 providing and fixing of aluminium bus bar of size 300mmx60mmx12 mm on l.t side of t/f. 15 making all connections with acb & distribution t/f and commissioning the acb complete in all respect. 16 replacement of old & damaged lt feeder piller (branch distribution pannel) and meter pannel box of various sectors in area of eudsd ii/xiii, noida as per following : 17 supply of new l.t. meter pannel boxes (three phase) for 08 nos. meter as per following specification with all relevant certificate: 1) providing of new l.t. meter pannel box of size 1350x1200 sq.mm. + 450x900 sq.mm. = 2.025 sq. mtrs. (as per drawing) made of ms sheet of 1.6 mm (+ 0.2 mm)/16 swg thick which required into 4 columns contains & feeders as per drawings enclosed of size 450x450 sq.mm. each for fixing the consumers meters, 01 nos. busbar chamber of size 900x300 sq.mm. for fixing 04 nos. aluminium bus bar for r, y, b &n in box & 450x300 sq.mm. feeder for incoming mccb 250 amp. all 04 nos. aluminum bus barsinsulation coated fo size 1000x75x10mm. shall be provided r, y, b & n by insulators. the metallic covers will have to be provided on each columns of the box. the side wall of box will have suitable holes for service cables. for fixing the meter pannel box, necessary arrangement by providing clamps, nut & bolts etc. are to be made. wiring of meter pannel box has to 10mm copper wire & lugs. complete meter pannel box (inside & outside) should be painted with one coat of red oxide primer then 02 coats of light grey enamel paint of reputed brand make. before painting the sun faces shall be thoroughly cleaned from dust, grease of rust. locking arrangement with 01 no. pad lock shall be provided on each cover of the meter pannel box. complete the work in all respect.2) meter pannel box mounting by ms angel 40x40x5mm for meter pannel box mounted on wall.3) incoming mccb of 250 amp. tp l&t / havell’s / abb make to be installed in meter pannel box.4) fixing of consumers meters in meter pannel box (08 nos. three phase) in each box or as per site requirement) and reconnection of consumers connections with the meters and cable reconnections with the bus bars. complete the work in all respect. 18 supply of new l.t. meter pannel boxes (three phase) for 16 nos. meter as per following specification with all relevant certificate: 1) providing of new l.t. meter pannel box of size 1350x1200 sq.mm. + 450x900 sq.mm. = 2.025 sq. mtrs. (as per drawing) made of ms sheet of 1.6 mm (+ 0.2 mm)/16 swg thick which required into 4 columns contains & feeders as per drawings enclosed of size 450x450 sq.mm. each for fixing the consumers meters, 01 nos. busbar chamber of size 900x300 sq.mm. for fixing 04 nos. aluminium bus bar for r, y, b &n in box & 450x300 sq.mm. feeder for incoming mccb 250 amp. all 04 nos. aluminum bus barsinsulation coated fo size 1000x75x10mm. shall be provided r, y, b & n by insulators. the metallic covers will have to be provided on each columns of the box. the side wall of box will have suitable holes for service cables. for fixing the meter pannel box, necessary arrangement by providing clamps, nut & bolts etc. are to be made. wiring of meter pannel box has to 10mm copper wire & lugs. complete meter pannel box (inside & outside) should be painted with one coat of red oxide primer then 02 coats of light grey enamel paint of reputed brand make. before painting the sun faces shall be thoroughly cleaned from dust, grease of rust. locking arrangement with 01 no. pad lock shall be provided on each cover of the meter pannel box. complete the work in all respect.2) meter pannel box mounting by ms angel 40x40x5mm for meter pannel box mounted on wall.3) incoming mccb of 250 amp. tp l&t / havell’s / abb make to be installed in meter pannel box.4) fixing of consumers meters in meter pannel box (16 nos. three phase) in each box or as per site requirement) and reconnection of consumers connections with the meters and cable reconnections with the bus bars. complete the work in all respect. 19 supply of new l.t. feeder pillar (branch distribution pannel)as per following specification with all relevant certificate : 1) lt feeder pillar box (branch distribution pannel) shall be of 14 swg hr sheet, having (2) doors, 1 in front and 1 doors on back side of 14 swg hr sheet. doors should have proper locking arrangements with providing crome locks of standard make. it should have a canopy on top in order to prevent it from water ingress in rains. the doors of box should be welded with robust quality hinges and pvc gasket with provision of 3 hinges on each door and handle on each door with pvc gasket. the periphery of door of the lt feeder pillar box (branch distribution pannel) shall be provided with lining of rubber/ pvc to prevent entry of rain, insects, lizards, rats etc. so as to make it vermin proof.2) the dimension of feeder pillar box (branch distribution pannel) 4(height) x 2.5(width) x 2(depth) feet (with canopy).3) 04 nos. bus bar insulation coated fo size 600x75x10mm. made of aluminum for red, yellow, blue & neutral phases suitable for 400 amp.4)01 no. mccb of 250 amp. of l&t / havell’s / abb make for disconnecting of supply.5) 24 nos. kit kat fuse of 415v, 250 amp. each capacity tested as per is shall be provided with 8 nos. on each phase so as to cater to 8nos. 3 phase connections of conusmer.6) aluminum crimping lugs of size 400 / 240 / 120 / 95 / 70sq.mm. and proper size thimbles shall be provided for safe termination of incomer as well as individual service cable as per qty. requirement.7) bakelite sheet shall be provided on the base of channel meant for mounting the kit kats.8) all nuts, bolts & washers used shall be electro galvanized.9)the height of erected feeder pillar box (branch distribution pannel) approx. 2feet from the earth on powder coatingbase of angle iron size 40x40x5mm frame with 04 nos. legs of 3 feet each (1 feet grout of angle on earth bottam, 1.6 feet grout in plinth and 6 inch gap in pannel base and plinth)10) grouting & plinth of feeder pillar box(branch distribution pannel) as per site requirement complete in all respects.11)the panel case consisting of door and roof (canopy) shall be powder coated with chemical process (weather proof) of off white color (or as per direction) both inside and outside. before painting, the sun faces shall be thoroughly cleaned from dust, grease and rust. ientification no. shall be written as per direction.12) sundry item. 20 disconncetion of all consumer connection from pannel as per requirement. 21 reconncetion of all consumer connection from pannel after replacement as per requirement. 22 dismantling of iron scap from earth on work site as per requirement. 23 carriage of above dismantled iron scap from works site to je store / central store & proper stacking with loading & unloading. 24 installation of abovenew l.t. feeder pillar (branch distribution pannel) & meter pannel box in place of damaged l.t. feeder pillar (branch distribution pannel) & meter pannel box with grouting, plinth and required items complete in all respect. 25 providing and installation of chemical earthing for acb, feeder pannel, meter pannel, dts (with all material and labour) after installation resistance should be less than one ohm. as per following (the all material and labour shall be provided by the contractor with 12 month guarantee for resistance value less than one ohm.) : 26 providing of earth elctrode for chemical earthing pipe in pipe typeproper hot deep galvanization dia 50 mm length 3 mtr 32mm x 6mmterminal connection hole dia 8mm the cavity between the pipe & pipe is filled with conductive mixture for hermetically filling inside the cavity i.e. between secondary conductor & primary conductor, crystalline compound is to be injected in the electrode assembly. it is a combination of high conductivity metal alloys, copper & aluminum power, conductive carbon / cement and bonding material etc the electrode should be sealed from both the ends. the outer pipe of the elctrode should be galavanized the characteristics of this compound is highly cnductive, non magnetic & non corrosive in g.i. including providing of backfill compound each elctrode should be supplied with bags of 25 kg x 2 bfc compound (ground resistance enhancement powder 50 kgs each cpri tested for lt acb, feeder pannel, meter pannel, dts installed at different places / dts. 27 providing and fixing of gi strip of size 32 mm x 6 mm suitable for lt acb, feeder pannel, meter pannel, dts installed at different places / dts. 28 providing and fixing of pvc pit covers for above earthing electrode terminals. 29 providing & fixing of al. lug size 400mm. 30 work of providing and fixing of 45 nos. new wiremesh fencing of 11/0.4 kv l.t. sub station installed at various place as per following : 31 providing & fixing of new wiremesh fencing frames of size 12x15x6for each fencing of lt sub stations.) (all material provided by contractor for above work.) 32 construction of boundry / toe wall in bottom of fencing in brick work cement mortar 1:6 (1 cement : 6 coarse sand) for link in the size of 0.22mx0.60m (0.30m in earth, 0.30m above ground level) including plaster in cement mortar 1:4 and finishing with water proof cement paint. (approx construction 12 mtrs. boundry / toe wall for each fencing of lt sub stations.) (all material provided by contractor for above work) 33 work of making 38 nos. new plinths distribution t/f in place of fully damage plinth / cahair at various place as per following : 34 unmounting of t/f from plinth disconnecting all connection work including loading, carriage & unloading from work site. 35 construction of new distribution t/f plinth. the size of plinth shall be 2 mtrs. long, 2 mtrs. wide and height 1.5 mtrs. from ground level with 15 cm thick top cc slab and ms channel 125x65mm. the above work includes excavation of earth, laying of bring ballast pad for foundation brick work, cc and plastering and proper curing complete with all respects as per respo schedule. (all material provided by contractor for above work.) 36 mounting of t/f on plinth making all connection work including loading, carriage & unloading from work site. 37 work of replacement of damaged s.t. pole erected in various h.t./l.t. line as per following : 38 removal of acsr conductor from both side spans of damaged pole and removal of h.t/l.t. line accessories from damaged pole. 39 diggingof pit of damaged pole in pakka road (hard soil) with the help of road cutter/digging machine, tractor etc. for dismantling the pole. 40 dismantling of damaged s.t pole of size 9 mtr. (metable scrap) from pit and s.t pole carriage from work site to j.es store including loading & unloading at both ends. 41 carriage of s.t. pole 9 mtr. is 410 sp 33 from cetral store, shaibabad/sector 20, noida/j.e store to work site including safe loading and unloading at both ends. 42 erection & fabrication of s.t. pole 9 mtr. is 410 sp 33 including fitting of all reqired accessories of ht/lt line as per respo schedule. 43 grouting, concreting (0.268 cu.m.each) and plinthing of single support on st pole with cement, stone ballast & coarse sand in ration of 1:3:6 complete in all respect. 44 re laying and resagging of acsr conductor in both side spans of erected pole in h.t/l.t line. 45 providing and fixing of clamps for st pole with nut & bolts 46 providing and fixing of ms bolts with nuts. ...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39827815 work under system augmentation plan in sub division haidergarh under ee, edd, haidergarh. 1 safe loading carriage including unloading and proper stacking of following materials from central store barabanki / je store to site of work. 2 pcc pole 8.5 3 11kv pin insulator . 4 11kv disc insulator . 5 top channel 11 kv 6 t off channel 11 kv 7 sub station base angle 8 ms earthing rod 9 transformer 63 kva 10 transformer 100kva 11 transformer 250 kva 12 transformer 400kva 13 transformer 25 kva 14 11 kv xple cable 3x70 / 120 / 185 sq mm 15 33 kv xple cable 3x300 sq mm 16 ltcable al 1x400 sq mm 17 ltcable al 1x400 sq mm 18 acsr weasal conductor 19 11 kv vcb panel outgoing ctr 200 / 100 / 5 a, 350 mva 20 11 kv vcb incomming ctr 600 / 300 / 5 a, 350 mva 24 volt. 21 stay set complete 22 other line material 23 safe carriage inclunding unloading proper stacking from store center barabanki to dump store of work site for maximum uto 1 to 6 no . pcc / stp poleas senction estimate ( pole quantity less then full capacity of carriar vehicle bot carriage chargeses will be paid as per full capacity in a job. ) 24 dragging of pole from je dump store to site 25 concreating and pilinthing of st& pccpole 18x24 cm. 26 erection of stay set of 16x1800 mm rod duly painted with red oxide, anchor plate, thumble turn buckle andstay insulate etc. digging of pit of size of size 0.4x0.6x1.6 m for grouting 1:3:6 cement concrete, with stay of size 7 / 8 swg, nuzzling & grouting. 27 stringing and sagging of 11 kv line with acsr weasal conductor including nuzzling binding and jumpering ( weasal conductor will be provided by the department ) 28 errectionof substation type double pole with pcc pole 8.5 mtr. long including mounting of top channal dropper channel, base angle with clamps with nut & bolt 33 / 11 kv line including grouting of support and plinthing 300 mm above ground level, fitting of 33 / 11 kv pin & pin insulator. 1 / 6 of total lenght of poles will remain under the ground and planted on stone pad of size 300x300x75 mm. 29 earthing of pole with ms earthing. 30 stringing and sagging of lt 3x50 abc cable ( lt abc cable will be provided by the department ) 31 fabricate with hole suitable size in steel items, receive from central store lightas top channel / dropper channel sub station base angle etc. 32 installation of mounting of following capacityof transformer including its connection between 11 kv and lt line mounting of copper l pieces, provinding crimping type aluminium lugs of required size. ( all the material except transformer will be arranged by the contractor ) 33 mounting of 63 kva tranformer 34 mounting of 100 kva tranformer 35 mounting of 250 kva tranformer 36 mounting of 400 kva tranformer 37 mounting of 25 kva tranformer 38 providingof various type materials. all materials shall be supplied by the contractor. 39 nut & bolt 40 clamp for top / dropper and t off channel etc. 41 gi pipe 6 dia 42 different size of lug 43 fixing of various type materials. all t& p and labour will be provided by the contractor. 44 nut & bolt 45 clamp for top / dropper and t off channel etc. 46 gi pipe 6 dia 47 different size of lug 48 installation of 11 kv vcb panel outgoing ctr 200 / 100 / 5 a, 350 mva 49 installation of 11 kv vcb incomming ctr 600 / 300 / 5 a, 350 mva 24 volt. 50 ltcable al 1x400 sq mm 51 wiremessfencing of 11 / 0.4 kvs / s shall be made of rectangular of size as per site requirement not exceeding 3 meter fabrication 45x45x5 mm angle the frame is also have 1 no. horizontal runner of ms flat 40x5 welded in middle to support of wire mess. rectangular welded type wire mess of size 50x25 made of 12 s.w.g. wire mess shall be welded all along the periphery of theframe as well as on horizontal runner to give extra strength of welding to wire mess welded on the frame. diagonal bracing of all the frame panel will be welded with ms flat of size 25x3mm to support as per respo specification & direction of e / i 52 construction of t / f plinth of size 2x2x1.5 mtr with first class brick and massionary work in the ratio 1:4 cement and core sand with rcc top 20 mm 1:2:2cement sand & core sand stone grit with 20 mm ms bar and ms channel for resting of t / f. 53 earthing of t / f pipe type with 40 fit deep borring and providing gi pipe 1.5 dia ( 60 fit gi pipe ) and gi strip 25x5 mmx6 meter long attached with clamps, l piece, nut & bolts and gi pipe cap. all material shall be supplied by the contractor. 54 laying of 11kv xlpe cable 3x70, 120, 185 sq.by mm manually 55 looping of cable and mounting of pole. 56 laying of 33kv xlpe cable 3x300sq.by mm manually 57 testing ofxlpe cable all size. 58 hosting of cable all size. 59 testing of control pannel 60 dismentaling of 10 / 16 / 25 / 63 / 100 / 250 kva t / f & carriage site to store 61 dismentaling& shifting of 250 kvat / f 62 other line work...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39827778 work under system augmentation plan in sub division deviganj under ee, edd, haidergarh. 1 safe loading carriage including unloading and proper stacking of following materials from central store barabanki / je store to site of work. 2 pcc pole 8.5 3 11kv pin insulator . 4 11kv disc insulator . 5 top channel 11 kv 6 t off channel 11 kv 7 sub station base angle 8 ms earthing rod 9 transformer 63 kva 10 transformer 100kva 11 transformer 250 kva 12 transformer 25 kva 13 11 kv xple cable 3x70 / 120 / 185 sq mm 14 acsr weasal conductor 15 11 kv vcb panel outgoing ctr 200 / 100 / 5 a, 350 mva 16 stay set complete 17 other line material 18 safe carriage inclunding unloading proper stacking from store center barabanki to dump store of work site for maximum uto 1 to 6 no . pcc / stp poleas senction estimate ( pole quantity less then full capacity of carriar vehicle bot carriage chargeses will be paid as per full capacity in a job. ) 19 dragging of pole from je dump store to site 20 concreating and pilinthing of st& pccpole 18x24 cm. 21 erection of stay set of 16x1800 mm rod duly painted with red oxide, anchor plate, thumble turn buckle andstay insulate etc. digging of pit of size of size 0.4x0.6x1.6 m for grouting 1:3:6 cement concrete, with stay of size 7 / 8 swg, nuzzling & grouting. 22 stringing and sagging of 11 kv line with acsr weasal conductor including nuzzling binding and jumpering ( weasal conductor will be provided by the department ) 23 errectionof substation type double pole with pcc pole 8.5 mtr. long including mounting of top channal dropper channel, base angle with clamps with nut & bolt 33 / 11 kv line including grouting of support and plinthing 300 mm above ground level, fitting of 33 / 11 kv pin & pin insulator. 1 / 6 of total lenght of poles will remain under the ground and planted on stone pad of size 300x300x75 mm. 24 earthing of pole with ms earthing. 25 stringing and sagging of lt 3x50 abc cable ( lt abc cable will be provided by the department ) 26 fabricate with hole suitable size in steel items, receive from central store lightas top channel / dropper channel sub station base angle etc. 27 installation of mounting of following capacityof transformer including its connection between 11 kv and lt line mounting of copper l pieces, provinding crimping type aluminium lugs of required size. ( all the material except transformer will be arranged by the contractor ) 28 mounting of 63 kva tranformer 29 mounting of 100 kva tranformer 30 mounting of 250 kva tranformer 31 mounting of 25 kva tranformer 32 providingof various type materials. all materials shall be supplied by the contractor. 33 nut & bolt 34 clamp for top / dropper and t off channel etc. 35 gi pipe 6 dia 36 different size of lug 37 33 kv x arm holding clamp 38 fixing of various type materials. all t& p and labour will be provided by the contractor. 39 nut & bolt 40 clamp for top / dropper and t off channel etc. 41 gi pipe 6 dia 42 different size of lug 43 installation of 11 kv vcb panel outgoing ctr 200 / 100 / 5 a, 350 mva 44 33 kv x arm holding clamp 45 wiremessfencing of 11 / 0.4 kvs / s shall be made of rectangular of size as per site requirement not exceeding 3 meter fabrication 45x45x5 mm angle the frame is also have 1 no. horizontal runner of ms flat 40x5 welded in middle to support of wire mess. rectangular welded type wire mess of size 50x25 made of 12 s.w.g. wire mess shall be welded all along the periphery of theframe as well as on horizontal runner to give extra strength of welding to wire mess welded on the frame. diagonal bracing of all the frame panel will be welded with ms flat of size 25x3mm to support as per respo specification & direction of e / i 46 construction of t / f plinth of size 2x2x1.5 mtr with first class brick and massionary work in the ratio 1:4 cement and core sand with rcc top 20 mm 1:2:2cement sand & core sand stone grit with 20 mm ms bar and ms channel for resting of t / f. 47 earthing of t / f pipe type with 40 fit deep borring and providing gi pipe 1.5 dia ( 60 fit gi pipe ) and gi strip 25x5 mmx6 meter long attached with clamps, l piece, nut & bolts and gi pipe cap. all material shall be supplied by the contractor. 48 laying of 11kv xlpe cable 3x70, 120, 185 sq.by mm manually 49 looping of cable and mounting of pole. 50 testing ofxlpe cable all size. 51 hosting of cable all size. 52 testing of control pannel 53 dismentaling of 10 / 16 / 25 / 63 / 100 / 250 kva t / f & carriage site to store 54 other line work...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39827759 work under additional business plan in sub division deviganj under ee, edd, haidergarh. 1 safe loading carriage including unloading and proper stacking of following materials from central store barabanki / je store to site of work. 2 pcc pole 8.5 3 11kv pin insulator . 4 11kv disc insulator . 5 top channel 11 kv 6 t off channel 11 kv 7 sub station base angle 8 ms earthing rod 9 transformer 63 kva 10 transformer 100kva 11 transformer 250 kva 12 transformer 400kva 13 transformer 25 kva 14 abc cable 3x50 sq. mm. 15 acsr weasal conductor 16 stay set complete 17 other line material 18 safe carriage inclunding unloading proper stacking from store center barabanki to dump store of work site for maximum uto 1 to 6 no . pcc / stp poleas senction estimate ( pole quantity less then full capacity of carriar vehicle bot carriage chargeses will be paid as per full capacity in a job. ) 19 dragging of pole from je dump store to site 20 concreating and pilinthing of st& pccpole 18x24 cm. 21 erection of stay set of 16x1800 mm rod duly painted with red oxide, anchor plate, thumble turn buckle andstay insulate etc. digging of pit of size of size 0.4x0.6x1.6 m for grouting 1:3:6 cement concrete, with stay of size 7 / 8 swg, nuzzling & grouting. 22 stringing and sagging of 11 kv line with acsr weasal conductor including nuzzling binding and jumpering ( weasal conductor will be provided by the department ) 23 errectionof substation type double pole with pcc pole 8.5 mtr. long including mounting of top channal dropper channel, base angle with clamps with nut & bolt 33 / 11 kv line including grouting of support and plinthing 300 mm above ground level, fitting of 33 / 11 kv pin & pin insulator. 1 / 6 of total lenght of poles will remain under the ground and planted on stone pad of size 300x300x75 mm. 24 earthing of pole with ms earthing. 25 stringing and sagging of lt 3x50 abc cable ( lt abc cable will be provided by the department ) 26 fabricate with hole suitable size in steel items, receive from central store lightas top channel / dropper channel sub station base angle etc. 27 installation of mounting of following capacityof transformer including its connection between 11 kv and lt line mounting of copper l pieces, provinding crimping type aluminium lugs of required size. ( all the material except transformer will be arranged by the contractor ) 28 munting of 63 kva tranformer 29 munting of 100 kva tranformer 30 munting of 250 kva tranformer 31 munting of 400 kva tranformer 32 munting of 25 kva tranformer 33 providingof various type materials. all materials shall be supplied by the contractor. 34 nut & bolt 35 clamp for top / dropper and t off channel etc. 36 fixing of various type materials. all t& p and labour will be provided by the contractor. 37 nut & bolt 38 clamp for top / dropper and t off channel etc. 39 wiremessfencing of 11 / 0.4 kvs / s shall be made of rectangular of size as per site requirement not exceeding 3 meter fabrication 45x45x5 mm angle the frame is also have 1 no. horizontal runner of ms flat 40x5 welded in middle to support of wire mess. rectangular welded type wire mess of size 50x25 made of 12 s.w.g. wire mess shall be welded all along the periphery of theframe as well as on horizontal runner to give extra strength of welding to wire mess welded on the frame. diagonal bracing of all the frame panel will be welded with ms flat of size 25x3mm to support as per respo specification & direction of e / i 40 construction of t / f plinth of size 2x2x1.5 mtr with first class brick and massionary work in the ratio 1:4 cement and core sand with rcc top 20 mm 1:2:2cement sand & core sand stone grit with 20 mm ms bar and ms channel for resting of t / f. 41 earthing of t / f pipe type with 40 fit deep borring and providing gi pipe 1.5 dia ( 60 fit gi pipe ) and gi strip 25x5 mmx6 meter long attached with clamps, l piece, nut & bolts and gi pipe cap. all material shall be supplied by the contractor. 42 dismentaling of 10 / 16 / 25 / 63 / 100 / 250 kva t / f & carriage site to store 43 dismentaling& shifting of 250 kvat / f 44 other line work...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39827712 work under additional business plan in sub division haidergarh under ee, edd, haidergarh, safe loading carriage including unloading and proper stacking of following materials from central store barabanki / je store to site of work. 2 pcc pole 8.5 2 pcc pole 8.5 3 11kv pin insulator . 4 11kv disc insulator . 5 top channel 11 kv 6 t off channel 11 kv 7 sub station base angle 8 ms earthing rod 9 transformer 63 kva 10 transformer 100kva 11 transformer 250 kva 12 transformer 400kva 13 transformer 25 kva 14 abc cable 3x50 sq. mm. 15 acsr weasal conductor 16 stay set complete 17 other line material 18 safe carriage inclunding unloading proper stacking from store center barabanki to dump store of work site for maximum uto 1 to 6 no . pcc / stp poleas senction estimate ( pole quantity less then full capacity of carriar vehicle bot carriage chargeses will be paid as per full capacity in a job. ) 19 dragging of pole from je dump store to site 20 concreating and pilinthing of st& pccpole 18x24 cm. 21 erection of stay set of 16x1800 mm rod duly painted with red oxide, anchor plate, thumble turn buckle andstay insulate etc. digging of pit of size of size 0.4x0.6x1.6 m for grouting 1:3:6 cement concrete, with stay of size 7 / 8 swg, nuzzling & grouting. 22 stringing and sagging of 11 kv line with acsr weasal conductor including nuzzling binding and jumpering ( weasal conductor will be provided by the department ) 23 errectionof substation type double pole with pcc pole 8.5 mtr. long including mounting of top channal dropper channel, base angle with clamps with nut & bolt 33 / 11 kv line including grouting of support and plinthing 300 mm above ground level, fitting of 33 / 11 kv pin & pin insulator. 1 / 6 of total lenght of poles will remain under the ground and planted on stone pad of size 300x300x75 mm. 24 earthing of pole with ms earthing. 25 stringing and sagging of lt 3x50 abc cable ( lt abc cable will be provided by the department ) 26 fabricate with hole suitable size in steel items, receive from central store lightas top channel / dropper channel sub station base angle etc. 27 installation of mounting of following capacityof transformer including its connection between 11 kv and lt line mounting of copper l pieces, provinding crimping type aluminium lugs of required size. ( all the material except transformer will be arranged by the contractor ) 28 munting of 63 kva tranformer 29 munting of 100 kva tranformer 30 munting of 250 kva tranformer 31 munting of 400 kva tranformer 32 munting of 25 kva tranformer 33 providingof various type materials. all materials shall be supplied by the contractor. 34 nut & bolt 35 clamp for top / dropper and t off channel etc. 36 fixing of various type materials. all t& p and labour will be provided by the contractor. 37 nut & bolt 38 clamp for top / dropper and t off channel etc. 39 wiremessfencing of 11 / 0.4 kvs / s shall be made of rectangular of size as per site requirement not exceeding 3 meter fabrication 45x45x5 mm angle the frame is also have 1 no. horizontal runner of ms flat 40x5 welded in middle to support of wire mess. rectangular welded type wire mess of size 50x25 made of 12 s.w.g. wire mess shall be welded all along the periphery of theframe as well as on horizontal runner to give extra strength of welding to wire mess welded on the frame. diagonal bracing of all the frame panel will be welded with ms flat of size 25x3mm to support as per respo specification & direction of e / i 40 construction of t / f plinth of size 2x2x1.5 mtr with first class brick and massionary work in the ratio 1:4 cement and core sand with rcc top 20 mm 1:2:2cement sand & core sand stone grit with 20 mm ms bar and ms channel for resting of t / f. 41 earthing of t / f pipe type with 40 fit deep borring and providing gi pipe 1.5 dia ( 60 fit gi pipe ) and gi strip 25x5 mmx6 meter long attached with clamps, l piece, nut & bolts and gi pipe cap. all material shall be supplied by the contractor. 42 dismentaling of 10 / 16 / 25 / 63 / 100 / 250 kva t / f & carriage site to store 43 dismentaling& shifting of 250 kvat / f 44 other line work...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39813040 strengthening work of poles and lines & increasing capacity of overloaded transformers under business plan 2023 24.” 1.01 top channel with clamp ( 125×65×2240 ) mm 1.02 dropper channel with clamp ( 100×50×2028 ) mm 1.03 t off channel with clamp 1.04 sub station base angle ( 75×75×6×2028 ) mm 1.05 lt clamp with nut bolt 1.06 lt shackle insulator 1.07 nut bolt for shackel insulator 1.08 25 kva t / f 1.09 63 kva t / f 1.1 100 kva t / f 1.11 250 kva t / f 1.12 400 kva t / f 1.13 pcc pole 8.5 mtr. long 1.14 st pole 11 mtr. long 1.15 lt xlpe cable alluninium 1×240mm2 1.16 lt xlpe cable alluninium 1×400mm2 1.17 lt xlpe cable alluninium 3.5×240mm2 1.18 lt xlpe cable alluninium 3.5×400mm2 1.19 abc cable ( 3×50+1×70+1×16 ) mm2 1.2 lt cable ( 3×95+1×35+1×16 ) mm2 1.21 abc cable ( 3×120+1×95+1×16 ) mm2 1.22 lt pvc cable 3.5x70 sqmm 1.23 lt pvc cable 3.5x150 sqmm 1.24 lt pvc cable 3.5x400 sqmm 1.25 g.i. wire 6 swg 1.26 11 kv fuese set 1.27 stay set complete 1.28 earthing complete 1.29 acsr weasel conductor 1.3 disc. insulator with fitting 1.31 11 kv pin insulator with g.i. pin 1.32 battery set 24 volt 1.33 work 1.34 erection of pcc pole 8.5 meter long single pole with grouting & with all accessories. 1.35 erection of pcc pole 8.5 meter long double pole with grouting & with all accessories. 1.36 abc cable ( 3x50+1x70+1x16 ) sq mm stringing sagging binding and jumpering of abc with all accessories 1.37 stringing & sagging of lt xlpe cable aluminum 1×400 sqmm as per respo norm 1.38 stringing & sagging of lt xlpe cable aluminum 1×240sqmm as per respo norm 1.39 stringing & sagging of lt xlpe cable aluminum 3.5x400sqmm as per respo norm 1.4 stringing & sagging of lt xlpe cable aluminum 3.5x240sqmm as per respo norm 1.41 ordinary earthing by 11 kv ms earth rod 2500 mm long as per respo schedule. all material except earthing rod shall be supplied by the contractor. 1.42 grouting and nozzling of 11 kv stay set complete including fixing of necessary clamps. accessories required including its grouting by civil material ( sand, brick blast & cement ) . all material except stay wire shall be supplied by the contractor. 1.43 stringing & sagging of three phase 11 kv acsr weasel conductor as per respo norm 1.44 fabrication, installation and commissioning of 25 / 16 / 10 kva t / f on double / single pole with all accessories. all material except 25 / 16 / 10 kva t / f shall be supplied by the contractor. 1.45 fabrication, installation & commissioning of 63 kva t / f on double pole with all accessories. all material except 63 kva t / f shall be supplied by the contractor. 1.46 placement of 11 / 0.4 kv t / fs from dump place to newly constructed t / fs plinth & installation, commissioning of 100 kva t / fs of t / f plinth and including jumpering with the system ( all the required martial for above job shall be provided by contractor except t / fs ) 1.47 placement of 11 / 0.4 kv t / fs from dump place to newly constructed t / fs plinth & installation, commissioning of 250 kva t / fs of t / f plinth and including jumpering with the system ( all the required martial for above job shall be provided by contractor except t / fs ) 1.48 placement of 11 / 0.4 kv t / fs from dump place to newly constructed t / fs plinth & installation, commissioning of 400 kva t / fs of t / f plinth and including jumpering with the system ( all the required martial for above job shall be provided by contractor except t / fs ) 1.49 looping & chopping of tree branches for clearance of ht / lt line after clearance of line throughout pieces of tree branches of site 1.5 installation fixing of 11kv fuse set ( all material arranged by the contractor except fuse set ) 1.51 construction of t / f plinth of size 2x2x1.5 m on a padding 0.25m deep in ground 1:5:10 cement sand and brick ballast on the top of padding brick work ist class brick of 0.95 mtr height & 0.35 mtr wall will be constructed. rest wall should be 0.23 mtr thick. brick work in ratio 1:4 cement & cores sand in the hollow portion the sand should be filled from the ground level up to 15 centimetres below from the top of wall, cement, sand & brick ballasts should be filled up to 15 centimetre. two no. of channel 100x50 in length 1500mm will be grouded.0.35 cm.rcc will be done with cores sand, cement and stone ballast in the ratio of 1:2:4.the t / fs plinth should be plastered on all sides 12mm thick in ratio 1:6 by cement and cores sand. ( all the material to be arranged by the contractor ) . 1.52 construction of toe wall around the 11 / 0.4 kv s / s, fuse unit size 0.75 mt. at base and 0.23 mt. at top as per resspo norms by lst class bricks in the ratio 1:6, base concreting of the wall to be done in ratio 1:6:12 and plaster 12 mm thick in ratio 1:4.& fabrication of fencing with wire mesh 10swg ( 37mmx50mm ) ( all material to be arranged by contractor ) . 1.53 installation of battery set 24 volt 1.54 dismantling of old & used ( existing ) material and loading, carriage & unloading from site to je dump store / store centre, hardoi. 1.55 10&16 kva t / f 1.56 25 kva t / f 1.57 63 kva t / f 1.58 100 kva t / f 1.59 250 kva t / f...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39813008 replacement of dilapidated wire of 250 kva single transformer located in village rampur pawti, fed from 33 / 11 kv power substation baghpat road i, in the work area of ​​subdivision i, baghpat road under power distribution division i, meerut, with abc. and installation of new poles in dilapidated poles and long spans and work of replacing dilapidated wire with abc of 63 kva sardar transformer situated in village rampur pawti and installation of new poles in dilapidated poles and long spans. 1 cartage of following material from store center meerut to site of work including loading & unloading at both ends maximum distance up to 30 km. : 2 pcc pole 8.5 mtr long 3 lt ab cable 3x120+1x95+1x16 sq.mm 4 lt ab cable 3x95+1x70+1x16 sq.mm 5 lt ab cable 3x50+1x35+1x16 sq.mm 6 3 phase lt distribution box 7 errection pcc pole 8.5 mtr. long after digging a pit of size 1.6 mtr deep in all type of soil including grouting of the pole with proper ramming after completion of work. 8 laying, lifting oflt ab cable 3x120+1x95+1x16 sq.mm 9 laying, lifting of lt ab cable 3x95+1x70+1x16 sq.mm 10 laying, lifting of lt ab cable 3x50+1x35+1x16 sq.mm 11 fixing of 3 phase lt distribution box 12 grouting of pole 13 earthing of pole 14 providing and fixing of dead and clamp with eye hook 15 providing and fixing of suspension clamp with eye hook 16 providing and fixing of piercing clamp 17 providing and fixing of ms clamps 18 providing and fixing of nut & bolt off size 19 back cartage old and used acsr weasal conductor...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39812845 under the additional business plan 2023 24 work received from electricity distribution division ii mitouli, replacement of 11 kv bcb in sub centre kamhara and construction of 33 kv new line under sub centre kalakam ( semi turnkey based work / decentralized all material executing agency ) the work will be payable by ) . 1 safe loading carriage including unloading and proper stacking of following materials from store center / je store to site of work and old dismentling material to store center / je store. 2 11kv outgoing vcb 200 / 100 / 5a 3 11kv incoming vcb 600 / 300 / 5a 4 11kv jointing kit 3x185 sq. mm xlpe hs i / d 5 installation of vcb as per respo norms and dismentling of old 11kv vcb at 33 / 11kv sub station kaimahra. 6 making delta earthing 7 safe loading carriage including unloading and proper stacking of following materials from store center / je store to site of work and old dismentling material to store center / je store. 8 stay set gi 30x1800 mm 9 11kv disc insulator ( b&s ) 70kn 10 steel tubler pole11mrt. long. 11 acsr dog conductor. 12 earth wire 7 / 16 swg 13 disc fitting for dog. 14 barbed wire. 15 g.i. pin 33kv with nut & bolt. 16 stay wire gi ( 7 / 4 mm ) 7 / 8 swg 17 33 kv v type cross arm 18 earth rod 2540x20mm 19 stay clamp for 11mtr. long stp 20 pin insulator 33kv 21 construction of 33kv overhead new line with all accessries under work are of 33 / 11kv sub station kala aam. as per approved estimate. 22 supply of holding clampr for st pole. 23 supply of aluminium paint.with work of 24 supply of ms top channel ( 125x65mm ) 2240mm long. 25 suppy of f bracket for 33kv line size 75x10mm. 26 supply of 33kv bracing angle. 27 supply of danger borard with clamp for 33kv line. 28 supply of red oxide paint. 29 supply of p.g. clam [ for dog to dog conductor. 30 grouting of stay. 31 grouting of stp pole. 32 supply of stay loop insulator. 33 supply of stone pad. 34 supply of nut & bolt....

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39812713 strengthening work of poles and lines & increasing capacity of overloaded transformers under business plan 2023 24 1 safe carriage, loading unloading with proper stacking of following materialfrom store centre hardoi to pit site / je dump store. 2 p.c.c. pole8.5mtr long 3 s.t. pole 11 mtr. long 4 11 kv pin insulator with pin 5 11 kv disc insulator with fitting 6 acsr weasel conductor 7 earthing complete 8 stay complete 9 g.i. wire 6 swg 10 abc cable ( 3×50+1×70+1×16 ) mm2 11 abc cable ( 3×95+1×70+1×16 ) mm2 12 lt xlpe cable aluminum 3.5×240mm2 13 lt xlpe cable aluminum 3.5×400mm2 14 lt xlpe cable aluminum 1×240mm2 15 lt xlpe cable aluminum 1×400mm2 16 lt xlpe cable aluminum 1×630mm2 17 25 kva t / f 18 63 kva t / f 19 100 kva t / f 20 250 kva t / f 21 400 kva t / f 22 630 kva t / f 23 stp pole 9mtr long 24 11 kv fuse set 25 line material 26 lt shackle insulator 27 aluminum lead 1x35 sqmm 28 lt shackle insulator ( 100x115 mm ) 29 1x630 mm* lt pvc cable 30 1x1000mm2ltpvccable ( lt stud to d / o fuse set ) 31 distribution box 3 phase 32 ix400 mm*lt pvc cable 33 work 34 erection of pcc 8.5 mtr long dingle pole with grouting & with all accessories 35 replacement of broken pcc single pole and erection of pcc pole 8.5 mtr long with grouting & with all accessories 36 erection of pcc 8.5 mtr long double pole with grouting & with all accessories 37 replacement of broken st single pole and erection of st pole 11 mtr long with grouting & with all accessories 38 erection of stp 11 mtr long double pole with grouting & with all accessories 39 grouting and nozzling of 11 kv stay set complete including fixing of necessary clamps. accessories required including its grouting by civil material ( sand, brick blast & cement ) . all material except stay wire shall be supplied by the contractor. 40 ordinary earthing by 11 kv ms earth rod 2500 mm long as per respo schedule. all material except earthing rod shall be supplied by the contractor. 41 stringing & sagging of lt xlpe cable aluminum 1×400mm2 42 stringing & sagging of lt xlpe cable aluminum 3.5×400mm2 43 stringing & sagging of lt xlpe cable ( 1×240 ) sq.mm. 44 stringing & sagging of lt xlpe cable ( 3.5×240 ) sq.mm. 45 stringing & sagging of lt xlpe cable ( 1×630 ) sq.mm. 46 earthling by way of boring and lowering the b class gi pipe ( jindal ) of 50mm dia from ground upto water level not less than 20mtr as per standard practice 47 placement of 11 / 0.4 kv t / fs from dump place to newly constructed t / fs plinth & installation, commissioning of 100 / 250 / 400 / 630 kva t / fs of t / fplinth and including jumpering with the system ( alltherequiredmartial for abovejob shall be provided by contractor except t / fs ) 48 fabrication erection & commissioning of 100 kva t / f on double pole with all accessories. all material except 100 kva t / f shall be supplied by the contractor. 49 fabrication erection & commissioning of 63 kva t / f on double pole with all accessories. all material except 63 kva t / f shall be supplied by the contractor. 50 fabrication erection and commissioning of 25 / 16 / 10 kva t / f on double / single pole with all accessories. all material except 25 / 16 / 10 kva t / f shall be supplied by the contractor. 51 stringing & sagging of three phase 11 kv line 52 stringing & sagging abc ( 3x50+1x35+1x16 ) sqmm 53 stringing & sagging abc ( 3x95+1x70+1x16 sqmm ) 54 installation & commissioning of distribution box for abc bunch conductor 55 looping & chopping of tree branches for clearance of ht / lt line after clearance of line throughout pieces of tree branches of site 56 supply & fixing of lt fuse unit for 250 & 400 with grout ( all material arrange by contractor at his own cost ) 57 supply & fixing of lt fuse unit for 630 with grout ( all material arrange by contractor at his own cost ) 58 fixing of ht fuse set 59 construction of t / f plinth of size 2x2x1.5 m on a padding 0.25m deep in ground 1:5:10 cement sand and brick ballast on the top of padding brick work ist class brick of 0.95 mtr height & 0.35 mtr wall will be constructed. rest wall should be 0.23 mtr thick. brick work in ratio 1:4 cement & cores sand in the hollow portion the sand should be filled from the ground level up to 15 centimeters below from the top of wall, cement, sand & brick ballasts should be filled up to 15 centimeter. two no. of channel 100x50 in length 1500mm will be grouded.0.35 cm.rcc will be done with cores sand, cement and stone ballast in the ratio of 1:2:4.the t / fs plinth should be plastered on all sides 12mm thick in ratio 1:6 by cement and cores sand. ( all the material to be arranged by the contractor ) . 60 construction of toe wall around the 11 / 0.4 kv s / s, fuse unit size 0.75 mt. at base and 0.23 mt. at top as per resspo normsby lst class bricks in the ratio 1:6, base concreting of the wall to be done in ratio 1:6:12 and plaster 12 mm thick in ratio 1:4.& fabrication of fencing with wire mesh 10swg ( 37mmx50mm ) ( all material to bearranged by contractor ) . 61 fixing of lt t / f mobile trolley at site 62 removal of lt t / f mobile trolley at site 63 dismantling of old & used ( existing ) material 64 dismantling of line ( scrap conductor ) 65 pcc 8.5 mtr long 66 stp pole 9 / 11 mtr long 67 100 / 250 kva t / f 68 63 / 25 / 16 kva t / f on double pole with all accessories. 69 loading & unloading from site to je dump store / store centre, hardoi. 70 dismantling of line ( scrap conductor ) 71 stp pole 9 / 11 mtr long 72 100 / 250 kva t / f 73 63 / 25 / 16 kva t / f on double pole with all accessories....

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39812638 tender for for different line maintenance works in full deposite head under edd powayan shahjahanpur under edc shahjahanpur ( mvvnl ) 1 safe loading carriage & unloading of following material from store centre to pit site / je dump store. 2 pcc pole 8.5 mtr long. 3 st pole 11 mtr. long. 4 11 kv xlpe cable of size 3x70 sq.mm. 5 11 kv xlpe cable of size ( 3x120, 3x185, 3x300 sqmm ) 6 33kv 3x120, 3x300sq mm xlpe cable 7 lt xlpe cable aluminum 3.5×240mm2 8 lt xlpe cable aluminum 3.5×400mm2 9 lt xlpe cable aluminum 1×240mm2 10 lt xlpe cable aluminum 1×400mm2 11 g.i wire 12 stay set complete 13 33, 11 kv pin with net 14 disc insulator with fitting ( b&s ) 70kn 15 ms earthing rod ( 2540x20 mm ) with fitting 16 11 kv indoor metering cubicle 17 11 / 0.4 kv t / f 250 / 400 / 630 kva 18 11 / 0.4 kv t / f 100 kva 19 11 / 0.4 kv t / f 63 kva 20 11 / 0.4 kv t / f 25 / 16 / 10 kva 21 11 kv outdoor, pole mounted ct / pt. unit. 22 acsr weasel conductor 23 dog / rabbit conductor 24 abc ( 1x16+1x25 ) sqmm 25 abc ( 3x50+1x35+1x16 ) sqmm 26 abc ( 3x95+1x70+1x16 sqmm ) 27 abc ( 3x120+1x95+1x16 sqmm ) 28 line meterial 29 cable box ( 3x70 / 3x120 / 3x185 / 3x300 ) indoor & outdoor 30 33 kv cable box 3x120, 3x300 sq mm cable straight through 31 work 32 erection of pcc 8.5 mtr long dingle pole with grouting & with all accessories 33 erection of pcc 8.5 mtr long double pole with grouting & with all accessories 34 erection of stp 11 mtr long single pole with grouting & with all accessories 35 erection of stp 11 mtr long double pole with grouting & with all accessories 36 fabrication & erection of cable stand made of two nos ms channel 100x50x3 mtr. long jointed to each other by means of 5nos ms strip 50x6mm of size 150mm long each by welding at equal distance interval as per norms and grouting in block of 300x300x700 completely providing two nos cable clamps also. all the materials i.e. clamps nut bolts will provide by contractor. 37 grouting and nozzling of 11 kv stay set complete including fixing of necessary clamps. accessories required including its grouting by civil material ( sand, brick blast & cement ) . all material except stay wire shall be supplied by the contractor. 38 ordinary earthing by 11 kv ms earth rod 2500 mm long as per respo schedule. all material except earthing rod shall be supplied by the contractor. 39 complete jumpering with help of gi pipe as per respo norms gi pipe and other required material shall be supplied by contractor. 40 laying of 11kv 3x70 sqmm single xlpe cable by digging of trench size 500 mm wide 900 mm after laying of brick, sand and stone slab. 41 laying of 11kv ( 3x120, 3x185, 3x300 sqmm ) single xlpe cable by digging of trench size 500 mm wide 900 mm after laying of brick, sand and stone slab. 42 stringing & sagging of lt xlpe cable aluminum 1×400mm2 43 stringing & sagging of lt xlpe cable aluminum 3.5×400mm2 44 stringing & sagging of lt xlpe cable ( 1×240 ) sq.mm. 45 stringing & sagging of lt xlpe cable ( 3.5×240 ) sq.mm. 46 digging of 33kv 3x120, 3x300sq mm xlpe cable, trench 1050 mm deep 500mm wide for laying of single xlpe cable in normal soil, supply and fixing of ist class bricks , stone slab , local sand filling of soil in trench , leveling and ramming of the same. 47 installation of 11 kv ct / pt double metering unit of constructed double pole structure as per respo norms. only 11 kv ct / pt unit shall be supplied by department. 48 fixing & commissioning of 11 kv pilfer resistance meter ( 25 / 5amp. ) all material except pilfer resistance metering cubical shall be supplied by the contractor. 49 earthling by way of boring and lowering the b class gi pipe ( gindal ) of 50mm dia from ground upto water level not less than 20mtr as per standard practice 50 construction of t / f plinth of size 2x2x1.5 m on a padding 0.25m deep in ground 1:5:10 cement sand and brick ballast on the top of padding brick work ist class brick of 0.95 mtr height & 0.35 mtr wall will be constructed. rest wall should be 0.23 mtr thick. brick work in ratio 1:4 cement & cores sand in the hollow portion the sand should be filled from the ground level up to 15 centimetres below from the top of wall, cement, sand & brick ballasts should be filled up to 15 centimetre. two no. of channel 100x50 in length 1500mm will be grouded.0.35 cm.rcc will be done with cores sand, cement and stone ballast in the ratio of 1:2:4.the t / fs plinth should be plastered on all sides 12mm thick in ratio 1:6 by cement and cores sand. ( all the material to be arranged by the contractor ) . 51 placement of 11 / 0.4 kv t / fs from dump place to newly constructed t / fs plinth & installation, commissioning of 100 / 250 / 400 / 630 kva t / fs of t / fplinth and including jumpering with the system ( alltherequiredmartial for abovejob shall be provided by contractor except t / fs ) 52 fabrication erection & commissioning of 100 kva t / f on double pole with all accessories. all material except 100 kva t / f shall be supplied by the contractor. 53 fabrication erection & commissioning of 63 kva t / f on double pole with all accessories. all material except 63 kva t / f shall be supplied by the contractor. 54 fabrication erection and commissioning of 25 / 16 / 10 kva t / f on double / single pole with all accessories. all material except 25 / 16 / 10 kva t / f shall be supplied by the contractor. 55 stringing & sagging of three phase 11 kv line 56 stringing & sagging of acsr dog / rabbit conductor 33 kvline 57 stringing & sagging abc ( 1x16+1x25 ) sqmm 58 stringing & sagging abc ( 3x50+1x35+1x16 ) sqmm 59 stringing & sagging abc ( 3x95+1x70+1x16 sqmm ) 60 stringing & sagging abc ( 3x120+1x95+1x16 sqmm ) 61 installation & commissioning of distribution box for abc bunch conductor 62 construction of toe wall around the 11 / 0.4 kv s / s, fuse unit size 0.75 mt. at base and 0.23 mt. at top as per resspo normsby lst class bricks in the ratio 1:6, base concreting of the wall to be done in ratio 1:6:12 and plaster 12 mm thick in ratio 1:4.& fabrication of fencing with wire mesh 10swg ( 37mmx50mm ) ( all material to bearranged by contractor ) . 63 instalation of cable box 11 kv indoor & outdoor 64 installation of 33kv 3x120, 3x300 sq mm out door end terminations ( provided by department ) 65 looping & chopping of tree branches for clearance of ht / lt line after clearance of line throughout pieces of tree branches of site ( approx 3 km ) . 66 dismantling of old & used ( existing ) material and loading, carriage & unloading from site to je dump store / store centre, shahjahanpur. 67 dismentling of line ( scrap conductor ) 68 pcc 8.5 mtr long single pole with all accessories 69 pcc8.5mtrlongdoublepolewith all accessories 70 stp 11 mtr long single pole with all accessories 71 stp 11 mtr long double polewith all accessories 72 transformer 250 / 400 / 630, kva 73 100 kva t / f on double pole with all accessories. 74 63 / 25 kva t / f on double pole with all accessories. 75 carriage of material pit site to shahajahanpur store je dump store / store center of shahjahanpur....

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39812117 tender for running contract for deposit works under edd ii, bareilly 1 the work of safe carriage of the following material from cb ganj store center to work siteunder the jurisdiction of edd ii, bareilly. approx. distance upto 80 km. including safe loading and unloading. 2 pcc pole 8.5 meter long. 3 stp 9 mtr long 4 stp 11 mtr long 5 line material i.e., cross arm/ conductor/ pin insulator/stay/earthing rod/disc fitting/disc insulators/11 kv xlpe cable etc 6 11/0.4 kv 1 phase 10/16 kva t/f 7 11/0.4 kv 3 phase 25 kva t/f 8 11/0.4 kv 3 phase 63 kva t/f 9 11/0.4 kv 3 phase 100 kva t/f 10 11/0.4 kv 3 phase 250 kva t/f 11 11/0.4 kv 3 phase 400 kva t/f 12 11 kv pilfer proof metering cubical and ct pt unit 13 33 kv pilfer proof metering cubical and ct pt unit 14 erection of new pcc single/double pole in h.t/l.t lines including fitting of all accessories as per resspo norms 15 pcc pole 8.5 mtr long single pole 16 pcc pole 8.5 mtr long double pole 17 st pole 9 mtr long single pole. 18 st pole 9 mtr long double pole. 19 st pole 11 mtr long single pole. 20 st pole 11 mtr long double pole. 21 grouting with 1:4:8 mixture in size(450x450x1500mm.) including cost of cement/bb & sand required as per resspo norms 22 pcc pole 8.5 mtr long single pole 23 pcc pole 8.5 mtr long double pole 24 st pole 9 mtr long single pole. 25 st pole 9 mtr long double pole. 26 st pole 11 mtr long single pole. 27 st pole 11 mtr long double pole. 28 the work of driving the earthing electrode and making connections with 6 s.w.g. gi wire as per resspo norms 29 dismantling of old and damaged conductor complete in all respect 30 dismantling of pcc/st pole due to line shifting/damaged complete in all respect 31 dismantling of existing distribution transformer for increasing capacity/shifting complete in all respect 32 11/0.4 kv 3 phase 25 kva t/f 33 11/0.4 kv 3 phase 63 kva t/f 34 11/0.4 kv 3 phase 100 kva t/f 35 11/0.4 kv 3 phase 250 kva t/f 36 11/0.4 kv 3 phase 400 kva t/f 37 laying, stringing & sagging of following conductor complete in all respect 38 acsr weasal conductor 39 acsr rabbit conductor 40 acsr dog conductor 41 3 phase arial bunched conductor 42 1 phase arial bunched conductor 43 after mounting of ct pt unit on double pole, laying of 50 mtr 11 kv 3cx70 sq mm cable in single circuit on river sand formdouble pole to metering room complete in all respect. alongwith filling of 04 nos cable jointing kits 44 after mounting of ct pt unit on double pole, laying of 50 mtr 33 kv 3cx120 sq mm cable in single circuit on river sand formdouble pole to metering room complete in all respect. alongwith filling of 04 nos cable jointing kits 45 under ground laying of following cable in single circuit on river sand to double pole situated at both sides of road complete in all respect. minimum depth should be 0.75 mtr and cable should be covered by bricks from three sides. alongwith filling of 04 nos cable jointing kits 46 11 kv xlpe cable size 3x70 sqmm 47 11 kv xlpe cable size 3x120 sqmm 48 11 kv xlpe cable size 3x185 sqmm 49 33 kv xlpe cable size 3x120 sqmm 50 33 kv xlpe cable size 3x185 sqmm 51 33 kv xlpe cable size 3x300 sqmm 52 under ground laying of following cable in single circuit by drill method to double pole situated at both sides of nh/sh/railway crossing complete in all respect.alongwith filling of 04 nos cable jointing kits 53 11 kv xlpe cable size 3x70 sqmm 54 11 kv xlpe cable size 3x120 sqmm 55 11 kv xlpe cable size 3x185 sqmm 56 33 kv xlpe cable size 3x120 sqmm 57 33 kv xlpe cable size 3x185 sqmm 58 33 kv xlpe cable size 3x300 sqmm 59 hoisting of following size 11 kv & 33 kv xlpe cableon double pole with gi pipe of size 6 dia 4 mtr long including the jumpering complete with clamps , nut and bolts. 60 11 kv xlpe cable size 3x70 sqmm 61 11 kv xlpe cable size 3x120 sqmm 62 11 kv xlpe cable size 3x185 sqmm 63 33 kv xlpe cable size 3x120 sqmm 64 33 kv xlpe cable size 3x185 sqmm 65 33 kv xlpe cable size 3x300 sqmm 66 supply & laying of 6 dia g pipe at various places i.e road crossing & hoisting etc. complete in all respect ((iso certified gi pipe 150 nb 3 mm thick dia 6 would be provided by contractor at his own cost) 67 construction of t/f plinth 1.5x1.5x2 m3 for mounting 250/400 kva t/f including foundation work (below ground 0.5 m), brick work, rcc slab of 4” thickness and plastering in 1:6 ratio with 02 nos channel pieces of 1.5 mtr long of size 100x50x6 mm compete in all respect all manpower, material and t&p provided by the contractor to complete the work. 68 cage fencing of 250/400 kva plinth mounted transformer in town areas to avoid electrical human/cattle accidents by fabrication of cage (1 inch sq wiremesh) made of 10 no gauge in suitable size angle iron frame of size 7.5(l)x5(w)x8’(h) by strengthening of wire mesh 20x3 mm m.s. flat horizontally as well as vertically, grouting the panel with 1:2:4 cement/coorse send/brick ballast. the frame should be bolted on angles at the four corners so that frame may be un bolted/bolted at the time of replacement of the transformer. provision of 1 gate should be there for maintenance of the transformer. painting (1 coat of red oxide + 2 coat of bus green enamel paint). the wire mesh should be earthed with 50x6 mm ms earthing strip with existing earthing of transformer body. all manpower, material and t&p provided by the contractor to complete the fabrication, transportation and installation. 69 the work of digging of pits, erection of stay clamp, insulator etc. 70 grouting of stays, 1:4:8 cc ratio (600x600x300mm.) as per respo norms. 71 installation of 11 kv pilfer proof metering cubicle in metering room complete in all respect 72 installation of 33 kv pilfer proof metering cubicle in metering room complete in all respect 73 mounting of following capacity transformers as per norms complete in all respect 74 10/16 kva t/f 75 25 kva t/f 76 63 kva t/f 77 100 kva t/f 78 250 kva t/f 79 400 kva t/f 80 fixing of distribution box complete in all respect 81 guarding at road crossing complete in all respect 82 supply & fixing of following items to complete the work (if not available in stores) 83 lt clamps as per resspo norms for pcc/st pole 84 nut & bolt off size 85 f clampas per resspo norms 86 shackle insulatoras per resspo norms 87 holding clamp for x arm, top. t off etc.as per resspo norms 88 stay clampsas per resspo norms 89 11 kv composite polymer disc insulatoras per resspo norms 90 top channel of size 100x50x2240 mmas per resspo norms 91 t off channelas per resspo norms 92 11 kv polymer pin insulator as per resspo norms 93 safe back carriage of scrap (if any) from work siteto c.b. ganj store bareilly approx distance upto 80 km including safe loading & unloading. 94 safe back carriage of distribution transformer from work siteto c.b. ganj store bareilly approx distance upto 80 km including safe loading & unloading. 95 11/0.4 kv 3 phase 25 kva t/f 96 11/0.4 kv 3 phase 63 kva t/f 97 11/0.4 kv 3 phase 100 kva t/f 98 11/0.4 kv 3 phase 250 kva t/f 99 11/0.4 kv 3 phase 400 kva t/f ...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39812091 strengthening work of poles and lines & increasing capacity of overloaded transformers under additional 1 safe carriage, loading unloading with proper stacking of following materialfrom store centre hardoi to pit site / je dump store. 2 p.c.c. pole8.5mtr long 3 s.t. pole 11 mtr. long 4 11 kv pin insulator with pin 5 11 kv disc insulator with fitting 6 acsr weasel conductor 7 earthing complete 8 stay complete 9 g.i. wire 6 swg 10 abc cable ( 3×50+1×70+1×16 ) mm2 11 abc cable ( 3×95+1×70+1×16 ) mm2 12 lt xlpe cable aluminum 3.5×240mm2 13 lt xlpe cable aluminum 3.5×400mm2 14 lt xlpe cable aluminum 1×240mm2 15 lt xlpe cable aluminum 1×400mm2 16 11 kvxlpe 3x120 mm2 17 cable box ( 3x70 / 3x120 / 3x185 / 3x300 ) indoor & outdoor 18 63 kva t / f 19 100 kva t / f 20 250 kva t / f 21 400 kva t / f 22 11 kv fuse set 23 line material 24 lt shackle insulator 25 11 kv vcb 600 / 300 / 5 a, 350 mva i / c 26 11 kv vcb 400 / 200 / 5 a, 350 mva o / g 27 work 28 erection of pcc 8.5 mtr long double pole with grouting & with all accessories 29 erection of stp 11 mtr long single pole with grouting & with all accessories 30 erection of stp 11 mtr long double pole with grouting & with all accessories 31 grouting and nozzling of 11 kv stay set complete including fixing of necessary clamps. accessories required including its grouting by civil material ( sand, brick blast & cement ) . all material except stay wire shall be supplied by the contractor. 32 ordinary earthing by 11 kv ms earth rod 2500 mm long as per respo schedule. all material except earthing rod shall be supplied by the contractor. 33 stringing & sagging of lt xlpe cable aluminum 1×400mm2 34 stringing & sagging of lt xlpe cable aluminum 3.5×400mm2 35 stringing & sagging of lt xlpe cable ( 1×240 ) sq.mm. 36 stringing & sagging of lt xlpe cable ( 3.5×240 ) sq.mm. 37 earthling by way of boring and lowering the b class gi pipe ( jindal ) of 50mm dia from ground upto water level not less than 20mtr as per standard practice 38 placement of 11 / 0.4 kv t / fs from dump place to newly constructed t / fs plinth & installation, commissioning of 100 / 250 / 400 / 630 kva t / fs of t / fplinth and including jumpering with the system ( alltherequiredmartial for abovejob shall be provided by contractor except t / fs ) 39 fabrication erection & commissioning of 100 kva t / f on double pole with all accessories. all material except 100 kva t / f shall be supplied by the contractor. 40 fabrication erection & commissioning of 63 kva t / f on double pole with all accessories. all material except 63 kva t / f shall be supplied by the contractor. 41 stringing & sagging of three phase 11 kv line 42 stringing & sagging abc ( 3x50+1x35+1x16 ) sqmm 43 stringing & sagging abc ( 3x95+1x70+1x16 sqmm ) 44 11 kv vcb 600 / 300 / 5 a, 350 mva i / c 45 11 kv vcb 400 / 200 / 5 a, 350 mva o / g 46 supply of mobile trolley for 250 kva t / f 47 fixing of ht fuse set 48 dismantling of old & used ( existing ) material 49 dismantling of line ( scrap conductor ) 50 100 / 250 kva t / f 51 63 / 25 / 16 kva t / f on double pole with all accessories. 52 loading & unloading from site to je dump store / store centre, hardoi. 53 dismentling of line ( scrap conductor ) 54 100 / 250 kva t / f 55 63 / 25 / 16 kva t / f on double pole with all accessories....

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39812052 strengthening work of poles and lines & increasing capacity of overloaded transformers under business plan 2023 24.” 1 safe carriage, loading unloading with proper stacking of following materialfrom store centre hardoi to pit site / je dump store. 2 top channel with clamp ( 125×65×2240 ) mm 3 dropper channel with clamp ( 100×50×2028 ) mm 4 sub station base angle ( 75×75×6×2028 ) mm 5 lt clamp with nut bolt 6 lt shackle insulator 7 nut bolt for shackle insulator 8 25 kva t / f 9 63 kva t / f 10 100 kva t / f 11 250 kva t / f 12 400 kva t / f 13 pcc pole 8.5 mtr. long 14 lt xlpe cable aluminum 1×240mm2 15 lt xlpe cable aluminum 1×400mm2 16 lt xlpe cable aluminum 3.5×240mm2 17 lt xlpe cable aluminum 3.5×400mm2 18 abc cable ( 3×50+1×70+1×16 ) mm2 19 abc cable ( 3×95+1×70+1×16 ) mm2 20 g.i. wire 6 swg 21 11 kv fuse set 22 stay set complete 23 earthing complete 24 acsr weasel conductor 25 disc. insulator with fitting 26 11 kv pin insulator with g.i. pin 27 work 28 erection of pcc pole 8.5 meter long single pole with grouting & with all accessories. 29 erection of pcc pole 8.5 meter long double pole with grouting & with all accessories. 30 abc cable ( 3x50+1x70+1x16 ) sq mm stringing sagging binding and jumpering of abc with all accessories 31 stringing & sagging of lt xlpe cable aluminum 1×400 sqmm as per resspo norm 32 stringing & sagging of lt xlpe cable aluminum 1×240sqmm as per respo norm 33 stringing & sagging of lt xlpe cable aluminum 3.5x400sqmm as per resspo norm 34 stringing & sagging of lt xlpe cable aluminum 3.5x240sqmm as per resspo norm 35 ordinary earthing by 11 kv ms earth rod 2500 mm long as per respo schedule. all material except earthing rod shall be supplied by the contractor. 36 grouting and nozzling of 11 kv stay set complete including fixing of necessary clamps. accessories required including its grouting by civil material ( sand, brick blast & cement ) . all material except stay wire shall be supplied by the contractor. 37 stringing & sagging of three phase 11 kv acsr weasel conductor as per resspo norm 38 fabrication, installation and commissioning of 25 / 16 / 10 kva t / f on double / single pole with all accessories. all material except 25 / 16 / 10 kva t / f shall be supplied by the contractor. 39 fabrication, installation & commissioning of 63 kva t / f on double pole with all accessories. all material except 63 kva t / f shall be supplied by the contractor. 40 placement of 11 / 0.4 kv t / fs from dump place to newly constructed t / fs plinth & installation, commissioning of 100 kva t / fs of t / fplinth and including jumpering with the system ( alltherequiredmartial for abovejob shall be provided by contractor except t / fs ) 41 placement of 11 / 0.4 kv t / fs from dump place to newly constructed t / fs plinth & installation, commissioning of 250 kva t / fs of t / fplinth and including jumpering with the system ( alltherequiredmartial for abovejob shall be provided by contractor except t / fs ) 42 placement of 11 / 0.4 kv t / fs from dump place to newly constructed t / fs plinth & installation, commissioning of 400 kva t / fs of t / fplinth and including jumpering with the system ( alltherequiredmartial for abovejob shall be provided by contractor except t / fs ) 43 looping & chopping of tree branches for clearance of ht / lt line after clearance of line throughout pieces of tree branches of site 44 installation fixing of 11kv fuse set ( all material arranged by the contractor except fuse set ) 45 earthing by way of boring and lowering the b class gi pipe ( jindal ) of 50mm dia from ground upto water level not less than 20mtr as per standard practice 46 construction of t / f plinth of size 2x2x1.5 m on a padding 0.25m deep in ground 1:5:10 cement sand and brick ballast on the top of padding brick work ist class brick of 0.95 mtr height & 0.35 mtr wall will be constructed. rest wall should be 0.23 mtr thick. brick work in ratio 1:4 cement & cores sand in the hollow portion the sand should be filled from the ground level up to 15 centimeters below from the top of wall, cement, sand & brick ballasts should be filled up to 15 centimeter. two no. of channel 100x50 in length 1500mm will be grouded.0.35 cm.rcc will be done with cores sand, cement and stone ballast in the ratio of 1:2:4.the t / fs plinth should be plastered on all sides 12mm thick in ratio 1:6 by cement and cores sand. ( all the material to be arranged by the contractor ) . 47 construction of retaining wall, fabrication & erection of wire mesh fencing of size 3+3 & 2.0 m height around transformer and distribution pillar box with retaining wall & 1 no. gate with locking arrangement made of ms angle iron of size 50×50×6 mm jointed with nuts and bolts. the panel must be supported with ms flat of size 50×6mm wire mesh of size 10 swg rectangle type as per norms of respo. ( all the material will be arranged by by the contractor at his own cost ) . 48 dismantling of old & used ( existing ) infrastructure and safe loading, unloading from site to j.e. store / center store hardoi 49 10&16 kva t / f 50 25 kva t / f 51 63 kva t / f 52 100 kva t / f 53 250 kva t / f...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39811994 carrying out the 04 nos. work increasing capacity / 02 nos. work construction of 11 / 0.4 kv s / s under eudd v / vii, noida respectivly in the juridiction of eudc i, noida ( total 06 nos. work in additional business plan rs. 30.00 crore for noida zone ) . 1 following 04 nos. work increasing capacity/ 02 nos. work construction of 11/0.4 kv s/s at various places under eudd v/vii, noida respectivly : 2 cartage of st poles 11 mtr long from esc noida/sahibabad/ ghaziabad /any other esc of meerut discom to je store and from je store to site of work including loading and unloading at both ends. 3 cartage of other line material such as 11kv disc insulator t&c type 4500 kg. (36 nos.), 11kv disc fitting (36 nos.), 11 kv pin insulator (42 nos.), 11 kv pin with nut (42 nos.), acsr dog conductor (640 mtrs.) etc. from esc noida/sahibabad/ghaziabad /any other esc of meerut discom to je store and from je store to site of work including loading and unloading at both ends. 4 cartage of lt abc 3x120+1x95+1x16 sq.mm. from esc noida/sahibabad/ ghaziabad /any other esc of meerut discom to je store and from je store to site of work including loading and unloading at both ends. 5 the excavation of foundation pit in cc road/ mix soil/ normal soil/ soft & hard rack by using heavy duty compressor and its back filling and leveling etc. the size of the pit will be 600x600x1800 mm for each pole and having a depth of 1/6 of the full length of the support. 6 erection of double pole on 11 mtr. long st pole for lt line including fixing of all accessories of lt line as per respo schedule complete in all respects. 7 erection of pole on 11 mtr. long st pole for lt line including fixing of all accessories of lt line as per respo schedule complete in all respects. 8 grouting of each pole (in ratio of 1:4:8 in cement, sand and brick ballast) in size 450mmx450mmx1800 mm as per respo schedule complete in all respects. 9 construction of plinth in size 450x450x300 mm of each (0.880 cu.m.each) pole above the ground level(in ratio of 1:3:6 in cement, sand and brick ballast) as per respo schedule complete in all respects. 10 erection of pole on 11 mtr. long st pole for lt line including fixing of all accessories of lt line as per respo schedule complete in all respects. 11 laying, lifting and final binding, sagging of acsr dog conductor including fixing of all accessories as per respo schedule complete in all respects. 12 laying, lifting and final binding, sagging of lt abc 3x120+1x95+1x16 sq.mm. including fixing of all accessories as per respo schedule complete in all respects. 13 providing & fabrication / fixing of following material of best quality for completion of work as per site requirement : 14 11 kv tpmo 15 11 kv fuse set 16 lt pvc cable al. 3.5x240 sq.mm.(laying of cable including fixing of all accessories as per respo schedule complete in all respects.) 17 stay set 16x1800 mm(grouting & concreting of stay rod 1800x16 mm complete in all respect as per respo schedule complete in all respects.), (fixing, tighting and nozzling of stay wire 5 kg with the pole of required tension with clamps, bolt & nut as per respo schedule complete in all respects.) 18 ms earthing rod (2540x20 mm) complete(excavation of earth and driving of m.s. earthing rod of size 20x2540 mm in earth and jointing through g.i wire of 6 swg between support and earth electrode by providing proper size of bolts and nuts etc. as per respo schedule complete in all respects.) 19 ms dropper channel 100x50x2028mm 20 stone pad 300x300x75 mm 21 clamp for lt (t off) with bolt and nuts 22 ms top channel 125x65x2240 mm 23 ms channel 125x65x1300mm (t off) 24 al. lug long barrel, off size (ls) 25 holding clamp for top channel, tpmo and fuse set etc with bolt and nuts. 26 11 kv v type cross arm 27 lt pvc cable al. 1x400 sq.mm.(laying of cable including fixing of all accessories as per respo schedule complete in all respects.) 28 danger board, barbed wire including jumper 29 red oxide paint 30 aluminium paint 31 st pole clamp 32 f clamp for pin insulator with nut & bolt 33 3 phse distribution box 34 lt piercing connector for size 120/95 35 clamp for distribution box with nut & bolt 36 lt 1x70 sq.mm. lead(laying of cable including fixing of all accessories as per respo schedule complete in all respects.) 37 construction of new distribution 250 kva t/f plinth. the size of plinth shall be 2 mtrs. long, 2 mtrs. wide and height 1.5 mtrs. from ground level with 15 cm thick top cc slab. the above work includes excavation of earth, laying of bring ballast pad for foundation brick work, cc and plastering and proper curing complete with all respects as per respo schedule. 38 safe loading and carriage of 250 kva transformerfrom esc noida/sahibabad/ ghaziabad /any other esc of meerut discom to je store and from je store to site of work including loading and unloading at both ends 39 mounting, installation of 250 kva transformer on above plinth, alongwith double earthing of the same, complete in all respect as per respo schedule. 40 panel fabrication of size 1250mm x 900mm x 600 mmmade of m.s sheet 14 gauge with powder coating with panel lock and key arrangement.(two nos). and additional locking arrangement seprately including providing hut type shape as per drg. 41 providing and installation oflt acb600 amp. with cabinet / structure (make l&t, schneider, abb, hevells) as per following specification with all relevant certificate : 42 600 amp. 03 pole fixed manual acb. 43 red/yellow/blue light indication 44 on & off indication 45 amp., voltmeter& energy meter digital 46 metering c.t 600/5a, 47 panel fabrication of size 1250mm x 900mm x 600 mmmade of m.s sheet 14 gauge with powder coating with panel lock and key arrangement.(two nos). and additional locking arrangement seprately including providing hut type shape as per drg. 48 fabrication ofaluminium bus bar for each phases 49 incoming size 425 mm x 50mmx12 mm (twin) 50 out going size 720 mm x 50mm x 12 mm(twin) 51 neutral size 900mmx50mmx12 mm. 52 fabrication of pannel stand made of m.s angle of size 900mm x 600mm x 500 mm as per drg. 53 assembly of above acb, indicators, meters, metering ct & bus bar arrangment in the panel, fitting the panel on stand with nut and boltswith wiringetc. & grouting inratio 1:4:8 with cement, coarse sand and brick blast. 54 providing and fixing of aluminium bus bar of size 300mmx60mmx12 mm on l.t side of t/f. 55 making all connections with acb & distribution t/f and commissioning the acb complete in all respect. 56 providing and installation of chemical earthing for 250 kva transformers (body & neutral) and acb (with all material and labour) after installation resistance should be less than one ohm. as per following (the all material and labour shall be provided by the contractor with 12 month guarantee for resistance value less than one ohm.) : 57 providing of earth elctrode for chemical earthing pipe in pipe typeproper hot deep galvanization dia 50 mm length 3 mtr 32mm x 6mmterminal connection hole dia 8mm the cavity between the pipe & pipe is filled with conductive mixture for hermetically filling inside the cavity i.e. between secondary conductor & primary conductor, crystalline compound is to be injected in the electrode assembly. it is a combination of high conductivity metal alloys, copper & aluminum power, conductive carbon / cement and bonding material etc the electrode should be sealed from both the ends. the outer pipe of the elctrode should be galavanized the characteristics of this compound is highly cnductive, non magnetic & non corrosive in g.i. including providing of backfill compound each elctrode should be supplied with bags of 25 kg x 2 bfc compound (ground resistance enhancement powder 50 kgs each cpri tested for 250 kva distribution t/f & acb installed at above 11/0.4 kv l.t. substation. 58 providing and fixing of gi strip of size 32 mm x 6 mm suitable for 250 kva distribution t/f & acb installed at above 11/0.4 kv l.t. substation. 59 providing and fixing of pvc pit covers for above earthing electrode terminals. 60 work of providing and fixing of 06 nos. new wiremesh fencing of 11/0.4 kv l.t. sub station installed at above place as per following : 61 providing & fixing of new wiremesh fencing frames of size 12x15x6for each fencing of lt sub stations.) (all material provided by contractor for above work.) 62 construction of boundry / toe wall in bottom of fencing in brick work cement mortar 1:6 (1 cement : 6 coarse sand) for link in the size of 0.22mx0.60m (0.30m in earth, 0.30m above ground level) including plaster in cement mortar 1:4 and finishing with water proof cement paint. (approx construction 12 mtrs. boundry / toe wall for each fencing of lt sub stations.) (all material provided by contractor for above work) ...

Madhyanchal Vidut Vitran Nigam Limited - Uttar Pradesh

39811968 strengthening work of poles and lines & increasing capacity of overloaded transformers under business plan 2023 24.” 1 safe carriage, loading unloading with proper stacking of following materialfrom store centre hardoi to pit site / je dump store. 2 top channel with clamp ( 125×65×2240 ) mm 3 dropper channel with clamp ( 100×50×2028 ) mm 4 t off channel with clamp 5 sub station base angle ( 75×75×6×2028 ) mm 6 gaurding angel with clamp 7 11 kv f clamp 8 lt clamp with nut bolt 9 lt shackle insulator 10 nut bolt for shackel insulator 11 11 kv v type x arm with holidng clamp 12 25 kva t / f 13 63 kva t / f 14 100 kva t / f 15 250 kva t / f 16 400 kva t / f 17 pcc pole 8.5 mtr. long 18 st pole 11 mtr. long. 19 abc cable ( 3×50+1×70+1×16 ) mm2 20 g.i. wire 6 swg 21 stay set complete 22 earthing complete 23 acsr weasel conductor 24 disc. insulator with fitting 25 pin insulator with g.i. pin 26 11 kv i / c vcb panel ctr 600 / 300 / 5a 27 11 kv o / g vcb panel ctr 200 / 100 / 5a 28 work 29 fabrication & erection of pcc 8.5 mtr long single pole with grouting & with all accessories like fixing of necessary clamp, neutral clamp abc pressure clamp, f clamp, x arm, t offand other necessary accessories. its grouting in ratio & plinthing above ground as per resspo norm ( all material to be managed by contractor as required ) 30 fabrication & erection of pcc 8.5 mtr long double pole with grouting & with all accessories erection of pcc 8.5 mtr long dingle pole with grouting & with all accessories like fixing of necessary clamp, neutral clamp abc pressure clamp, f clamp, x arm, t offand other necessary accessories. its grouting in ratio & plinthing above ground as per resspo norm ( all material to be managed by contractor as required ) 31 erection of stp 11 mtr long single pole with grouting, pole plinth & with all accessorieslike fixing of necessary clamp , i hook, dead / suspension clamp neutral clamp abc pressure clamp, f clamp, x arm, t offand other necessary accessories. its grouting in ratio & plinthing above ground as per resspo norm ( all material to be managed by contractor as required ) 32 ordinary earthing by 11 kv ms earth rod 2500 mm long as per respo schedule. all material except earthing rod shall be supplied by the contractor. 33 stringing & sagging of three phase 11 kv acsr weasel conductor as per respo norm with all accessories like jumpering, binding, nut & bolt and other required material ( material to be managed by contractor except conductor ) 34 guarding of above 11 kv line one span & height should be maintain as per resspo norms 6swg earth / gi wire 35 grouting and nozzling of 11 kv stay set complete including fixing of necessary clamps. accessories required including its grouting by civil material ( sand, brick blast & cement ) . all material except stay wire shall be supplied by the contractor. 36 abc cable ( 3x50+1x70+1x16 ) sq mm stringing sagging binding and jumpering of abc with all accessories like s / p distribution box, suspension clamp, i hook, dead end clamp and other material ( all material to be managed by contractor as required ) 37 construction of t / f plinth of size 2x2x1.5 m on a padding 0.25m deep in ground 1:5:10 cement sand and brick ballast on the top of padding brick work ist class brick of 0.95 mtr height & 0.35 mtr wall will be constructed. rest wall should be 0.23 mtr thick. brick work in ratio 1:4 cement & cores sand in the hollow portion the sand should be filled from the ground level up to 15 centimeters below from the top of wall, cement, sand & brick ballasts should be filled up to 15 centimeter. two no. of channel 100x50 in length 1500mm will be grouded.0.35 cm.rcc will be done with cores sand, cement and stone ballast in the ratio of 1:2:4.the t / fs plinth should be plastered on all sides 12mm thick in ratio 1:6 by cement and cores sand. ( all the material to be arranged by the contractor ) . 38 construction of toe wall around the 11 / 0.4 kv s / s, fuse unit size 0.75 mt. at base and 0.23 mt. at top as per resspo normsby lst class bricks in the ratio 1:6, base concreting of the wall to be done in ratio 1:6:12 and plaster 12 mm thick in ratio 1:4.& fabrication of fencing ( 3+3 & 2.0m height ) with wire mesh 10swg ( all material to bearranged by contractor ) . 39 earthling by way of boring and lowering the b class gi pipe ( jindal ) of 50mm dia from ground upto water level not less than 20mtr as per standard practice 40 fabrication, installation and commissioning of 25 / 16 / 10 kva t / f onnewly constructed double / single pole with all accessories including lugs, leads. all material except 25 / 16 / 10 kva t / f shall be supplied by the contractor. 41 fabrication, installation & commissioning of 63 kva t / f on newly constructed double pole with all accessories including lugs, leads. all material except 63 kva t / f shall be supplied by the contractor. 42 placement of 11 / 0.4 kv t / fs from dump place to newly constructed t / fs plinth & installation, commissioning of 100 kva t / fs of t / fplinth and including lugs, lead & jumpering with the system ( alltherequiredmartial for abovejob shall be provided by contractor except t / fs ) 43 complete mobile trolly set with 250kva / 400kva transformer which include fencing, painting of trolley, rubber mat, fixing of protection switchyard, , leads, lugs, fuse unit, earthing leads and other as per resspo norm , dimension as per resspo norm ( allthe martial for shall be provided by contractor except t / fs ) 44 looping & chopping of tree branches for clearance of ht / lt line after clearance of line throughout pieces of tree branches of site 45 installation, fixing of 11kv i / c vcb panel ctr 600 / 300 / 5a ( all material like control cable, ht tape, lugs wiring, and other as required arranged by the contractor except vcb panel ) 46 installation, fixing of 11kv o / g vcb panel ctr 200 / 100 / 5a ( all material like control cable, ht tape, lugs wiring, and other as required arranged by the contractor except vcb panel ) 47 dismantling of old & used ( existing ) material and loading, carriage & unloading from site to je dump store / store centre, hardoi. 48 dismantling of vcb panel, scrap material, conductor and other material 49 carriage of allmaterials like panel, scrap material, conductor material pit site to hardoi store je dump store / store center of hardoi. ( receive back to store centre ) ...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39811304 tender for various electrical work of electric supply in the area of edsd vth, etah ( edd iind, etah ) under additional business plan ( 339 cr. ) on semi turnkey basis. 1 supply of the line material as per relevent iss : 2 holding clamp for tf 3 nut & bolt with washer 4 stone pad 5 danger board 6 barbed wire 7 top channel 8 ms angle with clamp 9 pg clamp 10 clamp with nut & bolt 11 33 kv cable jonting kit o/d 3x300 sqmm 12 33 kv cable jonting kit i/d 3x300 sqmm 13 erection work : 14 safe carriage of line material from store center etah to pit site in distance range 0 to 60 km including loading & unloading at both ends. 15 safe carriage of following vcb from store center etah to pit site in distance range 0 to 60 km including loading & unloading at both ends. 16 11 kvvcb 17 33 kvvcb 18 safe carriage of 33 kv xlpe cable 3x300 sqmm from store center etah to pit site in distance range 0 to 60 km including loading & unloading at both ends. 19 safe carriage of 8.5 mtr long pcc pole from electricty store center etah/nearest 33/11 kv s/s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side 20 safe carriage of 13 mtr long st pole from electricty store center etah/nearest 33/11 kv s/s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side 21 safe carriage of 10 kva tf from electricty store center etah/nearest 33/11 kv s/s to direect pit site in distance range 0 to 60 kms.including loading and unloading at both side. 22 erection of 8.5 mtr long pcc pole as single support including fixing of ht/lt accessories etc and other work complete as per respo norms. 23 erection of 13 mtr long st pole as double pole/section pole including fixing of ht/lt accessories etc and other work complete as per respo norms. 24 dismantling and removal of existing acsr weasel/dog conductor conductor from the various area, stacking and placement their coils and their in the safer place including cost of lobour t&p etc. required for proper completion of work. 25 laying sagging stringing, binding, jumpering & fixing of all accessories etc of following conductor on the newly/old erected pole as per respo manual and as per direction of supervising engineer. it includes the cost of labour, t & p, carrier etc required for proper completion of work. 26 (a) acsr weseal conductor 27 (b) acsr dog conductor 28 (c) 33 kv xlpe cable 3x300 sqmm 29 (d) lt ab cable 3x50 sqmm 30 re sagging of looseweseal/dog conductor as per direction of supervising engineer. it includes the cost of labour, t & p carrier etc required for proper completion of work. 31 stone pad 32 pg clamp 33 earthing complete 34 33 kv vcb 800a, 750 mva 35 making of 33 kv vcb double tf control panel nct 200/100 1amp with structure as per respo norms. 36 11 kvvcb o/g ctr 200/100/5a, 350 mva 37 33 kv cable jonting kit o/d 3x300 sqmm 38 33 kv cable jonting kit i/d 3x300 sqmm 39 danger board with clamp 40 erection and grouting of stays as per respo norms and as per direction of supervising engineer. grouting material i.e. cement, sand, brick ballast/stone ballast etc. shall be arranged by the contractor at his own cost. 41 mounting of 10 kva tfincluding making of the connection etc. complete. 42 any other material/consumable required to complete the work shall be arrange by the contractor at his own cost. 43 carriage of acsr dog/rabbit/weseal conductor (scrap) from pit site to je store/store center etah in distance range 0 to 60 km. including loading & unloading and proper stacking. ...

Purvanchal Vidyut Vitaran Nigam Limited - Uttar Pradesh

39811300 tender for replacement overloaded transformer and erection of new dt under edd harraiya basti under b.p. head 2023 24 on semi turnkey basti 1 new 11 / 0.4 kv substation 2 safe loading carrige & unloading of pcc pole 9 mtr. poles from store to different work site at substation purani basti, gandhi nagar, gidahi, malviya road, badewan 3 safe carriage 10 / 25 / 63 / 100 kv transformer from store to different work site 4 loading carrige & unloding of remaining ht line material, acsr dog / weasel conductor 2.89 km, lt xlpe 0.26 km., 11 kv xlpe cable 0.22 km. & abc cable 1.7 km. from store to different site at substation gidahi, purani basti, gandhi nagar, badewan, malviya road, polytechnic 5 errection of single pcc pole with all fitting at different site ofwork substation gandhi nagar, purani basti, malviya road, badewan, gidahi 6 errection of double pcc pole with all fitting at different site of work substation gandhi nagar, purani basti, malviya road, badewan, gidahi 7 safe mounting & charging of 25 / 63 / 100 kva tf double poler earthing connection under different substation 8 earthing of pcc pole satnderd specifications 9 grouting of pcc polewith cement bricks ballast & coarse sand as per satnderd specifications 10 earthing of 10kva t / f on single pole 11 earthing of t / f...

Paschimanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39811269 the work of capacity increasing of dis. transformer , installation of new dis. transformer , construction of new lt line, division of 11 kv line, new 11kv vcb etc. work related to strengthening of 11 kv and lt lines under system strengthening in bp 23 24 under edd 2 bijnor. 1 safe carriage of the following material from store centre, bijnor to work site including loading & unloading at both ends. 2 pcc pole 8.5 mtr. long 3 63 kv t / f 4 100 kv t / f 5 lt abc ( 3x95+1x70+1x16 ) 6 acsr weasal conductor 7 line material 8 discinsulator 9 pininsulator with pin 10 11 kv vcb incoming ctr 600 / 300 / 5a, 350 mva, 24 volt 11 11 kv vcb outgoing ctr 200 / 100 / 5a, 350 mva 12 control cable 4x2.5 sqmm 13 control cable 2x2.5 sqmm 14 supply of following material including freight and insurance charges as per resspo norms. 15 sub station angle 16 tee channel 17 top channel 18 dropper channel 19 complete stay 20 complete earthing 21 11 kv fuse set 22 3 phase d. box set 23 suspension clamp with 1 hook installed 24 clamp holding / guarding of top dropper 25 m / s nuts bolts 26 locks for distribution.box 27 stone pad 28 end caps for lt abc 29 transformer mobile trolly suitable for 400 kva with fencing as per elcosed drawing / gtp. 30 installation of the following material as per respo manual and direction of the engineer incharge ( complete in all respect ) 31 digging of pits of pcc pole as per resspo norm. 32 erection of pcc pole 8.5 mtr long lt line with all accessories as per resspo norms 33 erection of d / p 8.5 mtr long with all accessories as per resspo norms 34 laying of lifting sagging & binding properly of acsr weasal conductor suitable for 11 kv line 35 laying of lifting sagging & binding properly of ab conductor suitable for lt line 36 laying of control cable 4x2.5 sqmm with proper connection 37 laying of control cable 2x2.5 sqmm with proper connection 38 mounting of 100 / 63 kva t / f proper ht / lt connection 39 grouting of pcc pole cement & bricks ballast 40 grouting of stay set in 1:4:8 cement and brick ballast and nozzling of stay wire 41 erection of top & dropper channel 42 erection of ms substaion angle 65x65x6 mm with clamp 43 erection of ms t off channel 100x1250x50 mm with clamp 44 erection of pole earthing with grouting as per resspo norms 45 erection of disc fitting with insulator 46 erection of 11 kv composit polimer pin insulator with pin 47 erection of 11 kv incoming vcb panel with proper ht connection as per resspo norms 48 erection of 11 kv outgoing vcb panel with proper ht connection as per resspo norms 49 erection of 3 phase d. box set as per resspo norms 50 erection of11 fuse set as per resspo norms 51 dismentallingand back cartage of following materialfrom work site to store centre bijnor with loading & unloading at both ends. 52 oldvcb withcontrol panel...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39811204 work of extension of lt / lt lines for electricity connections to the proposed mrf centers under the power distribution division auraiya / dibiyapur under the electricity distribution board auraiya 1 supply and erection of following material against replacement / installation / laying of item / erection of material as per respo drawings / estimate. work includes all cartage / carriage ( store to site ) , t&p, commissioning and any other work which is required for completion of work. as per respo norms. 2 nut & bolt 3 acsr weasal conductor 4 stay complete 5 earthing complete 6 t off channel 7 t off channel clamp 8 11 kv disc insulator with fiting 9 11 kv pin insulator with nut 10 dp clamp 11 cross arm 12 cross arm holding clamp 13 f clamp for pcc 14 dropper channel 15 top channel 16 t / f base angle 17 danger board 18 concreting of pcc pole 19 25 kva 11 / .4 kv tf new 20 st pole 11 m 21 63 kva 11 / 0.4 kv t / f 22 pcc pole 8.5 m 23 dropper channel 24 top channel 25 top & droper channel clamp 26 disc insulator with fitting 27 t off channel 28 earthing complete 29 stay complete with stay wire 30 11 kv cross arm 31 11 kv cross arm holding clamp 32 gaurding angle 33 gaurding angle clamp 34 gi wire for guarding 6 swg 35 pin insulator with gi pin 36 grouting of pole 37 stay wire 7 / 10 swg 38 gi pin 11 kv with nut...

Dakshinanchal Vidyut Vitran Nigam Limited - Uttar Pradesh

39811184 work of replacement of dilapidated 33 kv line and installation of pole of 33 / 11 kv power sub station under power distribution division dibiyapur. x. l. p. work of changing cable, changing double circuit dog conductor etc. and work of adding 33 kv line isolator, double circuiting the cable, changing gt / pt decker etc. of 33 kv sub stations under power distribution division dibiyapur. 1 supply and erection of following material against replacement / installation / laying of item / erection of material as per respo drawings / estimate. work includes all cartage / carriage ( store to site ) , t&p, commissioning and any other work which is required for completion of work. as per respo norms. 2 cable box indoor3x300 sqmm 3 cable box out door 3x300 sqmm 4 outdoor jointing kit 3x300 sqmm 5 indoor jointing kit 3x300 sqmm 6 bolts, nut & washers 7 xlpe cable 3x300 sqmm 33kv 8 pcc pole 8.5 m 9 st pole for 33 kv 10 stay complete 11 cross arm 12 33 kv disc insulator 13 holding clamp 14 brasing angle 15 33 kv disc with fitting 16 33 kv pin insulator with gi pin 17 grouting of pole 18 9 m long pcc pole 19 33 kv pin insulator 20 33 kv pin with nut 21 pg clamp for dog conductor 22 f bracket for 33 kv 23 earthing complete 24 stay complete 25 33 kv v type cross arm 100x50x6 mm 26 cross arm holding clamp with bolt & nut 27 stone pad 28 concreting of support 29 11 m st pole sp 55 30 top channle 125x65 mm 3200 mm 31 disc insulator 7000 kg 32 disc fitting dog 7000 kg 33 danger borad with clamp for 33 kv 34 acsr dog conductor 35 gaurding angle 36 gaurding angle clamp 37 gi wire 8 / 10 swg 38 dp clamp 39 cross arm holding clamp for st pole 40 f bracket for st pole 41 11 kv xlpe cable 3x300 sqmm 42 33 kv line isolator 800 amp 33 kv 43 line isolater...